{
  "model_key": "claude_fable_51",
  "display_name": "Claude Fable 5.1",
  "provider": "anthropic",
  "evaluation_model_ids": [],
  "thinking_effort": "max",
  "configuration_note": "Claude Fable 5.1 answered the 50 tasks in three rollouts through OpenRouter's chat completions route (anthropic/claude-fable-5.1) at maximum reasoning effort. Requests set max_tokens to 128,000, the model's output limit. Each request was one user message holding only the question text and its figure: no title, headings or system prompt. Answers cut off at the output limit were re-run; every attempt is counted in tokens and cost. Answers were graded by GPT-6 Luna at maximum reasoning effort. Cost uses OpenRouter's list price for Claude Fable 5.1 on 2026-11-10 ($10.00 input, $0.25 cached input, $50.00 output per 1M tokens).",
  "mode": "direct_qa",
  "summary": {
    "rollout_count": 3,
    "answer_count": 150,
    "scores": {
      "overall": {
        "gpt_6_luna_max": {
          "response_count": 150,
          "correct_count": 131,
          "incorrect_count": 19,
          "partial_credit_count": 19,
          "zero_count": 0,
          "mean_score_0_to_4": 3.7466666666666666,
          "score_percent": 93.66666666666667,
          "score_distribution": {
            "1": 5,
            "2": 9,
            "3": 5,
            "4": 131
          }
        },
        "active": {
          "response_count": 150,
          "correct_count": 131,
          "incorrect_count": 19,
          "partial_credit_count": 19,
          "zero_count": 0,
          "mean_score_0_to_4": 3.7466666666666666,
          "score_percent": 93.66666666666667,
          "score_distribution": {
            "1": 5,
            "2": 9,
            "3": 5,
            "4": 131
          }
        }
      },
      "part1": {
        "gpt_6_luna_max": {
          "response_count": 90,
          "correct_count": 89,
          "incorrect_count": 1,
          "partial_credit_count": 1,
          "zero_count": 0,
          "mean_score_0_to_4": 3.988888888888889,
          "score_percent": 99.72222222222223,
          "score_distribution": {
            "3": 1,
            "4": 89
          }
        },
        "active": {
          "response_count": 90,
          "correct_count": 89,
          "incorrect_count": 1,
          "partial_credit_count": 1,
          "zero_count": 0,
          "mean_score_0_to_4": 3.988888888888889,
          "score_percent": 99.72222222222223,
          "score_distribution": {
            "3": 1,
            "4": 89
          }
        }
      },
      "part2": {
        "gpt_6_luna_max": {
          "response_count": 60,
          "correct_count": 42,
          "incorrect_count": 18,
          "partial_credit_count": 18,
          "zero_count": 0,
          "mean_score_0_to_4": 3.3833333333333333,
          "score_percent": 84.58333333333333,
          "score_distribution": {
            "1": 5,
            "2": 9,
            "3": 4,
            "4": 42
          }
        },
        "active": {
          "response_count": 60,
          "correct_count": 42,
          "incorrect_count": 18,
          "partial_credit_count": 18,
          "zero_count": 0,
          "mean_score_0_to_4": 3.3833333333333333,
          "score_percent": 84.58333333333333,
          "score_distribution": {
            "1": 5,
            "2": 9,
            "3": 4,
            "4": 42
          }
        }
      }
    },
    "by_rollout": {
      "1": {
        "response_count": 50,
        "correct_count": 43,
        "incorrect_count": 7,
        "partial_credit_count": 7,
        "zero_count": 0,
        "mean_score_0_to_4": 3.74,
        "score_percent": 93.5,
        "score_distribution": {
          "1": 2,
          "2": 2,
          "3": 3,
          "4": 43
        }
      },
      "2": {
        "response_count": 50,
        "correct_count": 46,
        "incorrect_count": 4,
        "partial_credit_count": 4,
        "zero_count": 0,
        "mean_score_0_to_4": 3.8,
        "score_percent": 95.0,
        "score_distribution": {
          "1": 2,
          "2": 2,
          "4": 46
        }
      },
      "3": {
        "response_count": 50,
        "correct_count": 42,
        "incorrect_count": 8,
        "partial_credit_count": 8,
        "zero_count": 0,
        "mean_score_0_to_4": 3.7,
        "score_percent": 92.5,
        "score_distribution": {
          "1": 1,
          "2": 5,
          "3": 2,
          "4": 42
        }
      }
    },
    "tokens": {
      "response_count": 150,
      "usage_record_count": 150,
      "complete_usage_count": 150,
      "missing_usage_count": 0,
      "missing_cached_input_count": 0,
      "complete": true,
      "totals": {
        "cached_input_tokens": 0,
        "input_tokens": 293850,
        "output_tokens": 1795004,
        "total_tokens": 2088854
      },
      "known_totals": {
        "cached_input_tokens": 0,
        "input_tokens": 293850,
        "output_tokens": 1795004,
        "total_tokens": 2088854
      }
    },
    "by_rollout_part": {
      "part1": {
        "1": {
          "response_count": 30,
          "correct_count": 30,
          "incorrect_count": 0,
          "partial_credit_count": 0,
          "zero_count": 0,
          "mean_score_0_to_4": 4.0,
          "score_percent": 100.0,
          "score_distribution": {
            "4": 30
          }
        },
        "2": {
          "response_count": 30,
          "correct_count": 30,
          "incorrect_count": 0,
          "partial_credit_count": 0,
          "zero_count": 0,
          "mean_score_0_to_4": 4.0,
          "score_percent": 100.0,
          "score_distribution": {
            "4": 30
          }
        },
        "3": {
          "response_count": 30,
          "correct_count": 29,
          "incorrect_count": 1,
          "partial_credit_count": 1,
          "zero_count": 0,
          "mean_score_0_to_4": 3.966666666666667,
          "score_percent": 99.16666666666667,
          "score_distribution": {
            "3": 1,
            "4": 29
          }
        }
      },
      "part2": {
        "1": {
          "response_count": 20,
          "correct_count": 13,
          "incorrect_count": 7,
          "partial_credit_count": 7,
          "zero_count": 0,
          "mean_score_0_to_4": 3.35,
          "score_percent": 83.75,
          "score_distribution": {
            "1": 2,
            "2": 2,
            "3": 3,
            "4": 13
          }
        },
        "2": {
          "response_count": 20,
          "correct_count": 16,
          "incorrect_count": 4,
          "partial_credit_count": 4,
          "zero_count": 0,
          "mean_score_0_to_4": 3.5,
          "score_percent": 87.5,
          "score_distribution": {
            "1": 2,
            "2": 2,
            "4": 16
          }
        },
        "3": {
          "response_count": 20,
          "correct_count": 13,
          "incorrect_count": 7,
          "partial_credit_count": 7,
          "zero_count": 0,
          "mean_score_0_to_4": 3.3,
          "score_percent": 82.5,
          "score_distribution": {
            "1": 1,
            "2": 5,
            "3": 1,
            "4": 13
          }
        }
      }
    }
  },
  "answers": [
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It (approximately) doubles.**\n\nIntrinsic gain is \n\n$$A_v = g_m r_o$$\n\nConsider the two pieces when both W and L are doubled (so W/L stays the same) at the same bias current:\n\n- **g_m is unchanged.** Since $g_m = \\sqrt{2\\mu C_{ox}(W/L)I_D} = 2I_D/V_{ov}$, and W/L and I_D are the same, the overdrive and hence g_m don't change.\n\n- **r_o doubles.** Channel-length modulation gets weaker with longer channels: $\\lambda \\propto 1/L$ (equivalently, the Early voltage $V_A = V_A' \\cdot L$ scales with L). So $r_o = 1/(\\lambda I_D) = V_A/I_D$ doubles.\n\nPutting it together:\n\n$$A_v = g_m r_o = \\frac{2I_D}{V_{ov}}\\cdot\\frac{V_A' L}{I_D} = \\frac{2V_A' L}{V_{ov}} \\;\\;\\rightarrow\\;\\; \\text{doubles when } L \\text{ doubles}$$\n\nNote that the width doubling by itself does nothing for intrinsic gain—it only serves to keep W/L (and therefore V_ov, g_m, and I_D) the same. The gain improvement comes entirely from the longer channel.\n\n**The price you pay:** gate area quadruples, so C_gs (∝ WL) is ~4× larger while g_m is unchanged, meaning f_T = g_m/(2πC_gs) drops by roughly 4×. This is the classic gain-vs-speed trade-off in choosing channel length.",
        "format": "markdown",
        "sha256": "69184eb2214acd755899d90ffa1cf9bd2c22f897bdf11f5b63ea4f6deb130707"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that intrinsic gain approximately doubles: with W/L and bias current unchanged, gm stays about the same while the longer channel roughly doubles ro. The additional speed trade-off is consistent with the stated scaling.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1367,
        "total_tokens": 1403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 811,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1367,
        "total_tokens": 1403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 811,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It approximately doubles.**\n\nIntrinsic gain is\n\n$$A_v = g_m r_o = \\frac{g_m}{g_{ds}}$$\n\nLook at the two factors separately (assuming the bias current I_D is kept the same):\n\n- **g_m stays the same.** Doubling both W and L leaves the aspect ratio W/L unchanged, so for the same I_D the overdrive voltage is unchanged and\n $g_m = \\sqrt{2\\mu C_{ox}(W/L)I_D} = 2I_D/V_{ov}$ is unchanged.\n\n- **r_o doubles.** The channel‑length‑modulation parameter scales roughly as $\\lambda \\propto 1/L$ (equivalently, Early voltage $V_A \\propto L$). Doubling L halves λ, so\n $r_o = \\dfrac{1}{\\lambda I_D} = \\dfrac{V_A}{I_D}$ doubles.\n\nPutting it together:\n\n$$A_v = g_m r_o = \\frac{2I_D}{V_{ov}}\\cdot\\frac{V_A}{I_D} = \\frac{2V_A}{V_{ov}} \\;\\;\\propto\\; L$$\n\nso the intrinsic gain goes up by a factor of ~2.\n\n**Caveats / trade-offs:**\n- This is the first-order (square-law) picture. In short-channel devices, effects like DIBL and velocity saturation make the dependence on L less clean, but the trend (longer L → higher gain) still holds.\n- The price: gate area (W·L) quadruples, so C_gs quadruples while g_m is unchanged, meaning f_T = g_m/(2πC_gs) drops by ~4×. You trade speed for gain — the classic analog design trade-off.",
        "format": "markdown",
        "sha256": "9c1354c0a3eb8c82e8fc28e7f9039c9a26b5859afbd9ca59beb0fb27cb64d9c8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that intrinsic gain approximately doubles: with W/L and drain current unchanged, gm stays approximately constant while ro doubles as channel length increases. The stated bias assumption and first-order caveat are appropriate.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1499,
        "total_tokens": 1535,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 911,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1499,
        "total_tokens": 1535,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 911,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It roughly doubles.**\n\nIntrinsic gain is \n\n$$A_v = g_m r_o$$\n\n- **$g_m$ stays the same.** The aspect ratio $W/L$ is unchanged, so for the same bias current the overdrive $V_{ov}$ is the same and $g_m = 2I_D/V_{ov} = \\sqrt{2\\mu C_{ox}(W/L)I_D}$ is unchanged.\n\n- **$r_o$ doubles.** Channel‑length modulation scales as $\\lambda \\propto 1/L$ (equivalently, the Early voltage $V_A \\propto L$). Doubling $L$ halves $\\lambda$, so $r_o = 1/(\\lambda I_D)$ doubles.\n\nPutting it together:\n\n$$A_v = g_m r_o = \\frac{2I_D}{V_{ov}}\\cdot\\frac{1}{\\lambda I_D} = \\frac{2V_A}{V_{ov}} \\propto L$$\n\nso the intrinsic gain goes up by about 2×.\n\n**Caveats / trade‑offs:**\n- The $V_A \\propto L$ relationship is only approximate, especially for short‑channel devices, so \"about 2×\" rather than exactly 2×.\n- The gate area ($W \\cdot L$) quadruples, so $C_{gs}$ (and other capacitances) rise ~4×. With $g_m$ unchanged, $f_T = g_m/(2\\pi C_{gs})$ drops by ~4×. You've traded speed for gain — the classic analog design trade‑off that is why long‑channel devices are used in high‑gain, low‑frequency stages.",
        "format": "markdown",
        "sha256": "7cb6e8476df291e756f22f9e9f32fc6bc42e3ae0c1ec0d6b18b0de4636ec9e2a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that intrinsic gain approximately doubles: unchanged W/L and bias conditions keep gm and ID roughly constant, while doubling L approximately doubles ro. The additional speed trade-off is secondary and does not undermine the answer.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1457,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 36,
        "output_tokens": 1457,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Both can be right — it depends on what is held constant.** The disagreement comes from the fact that transconductance in saturation can be written three equivalent ways:\n\n$$g_m = \\mu_n C_{ox}\\frac{W}{L}V_{ov} \\;=\\; \\sqrt{2\\mu_n C_{ox}\\frac{W}{L}I_D} \\;=\\; \\frac{2I_D}{V_{ov}}$$\n\nwhere $V_{ov} = V_{GS} - V_{TH}$.\n\n**Student A is correct** in the most common situation: a given transistor (fixed W/L) whose gate voltage is raised. Then $V_{ov}$ increases, the drain current increases as $V_{ov}^2$, and $g_m = \\mu_n C_{ox}(W/L)V_{ov}$ rises linearly with the overdrive. This is the usual textbook statement.\n\n**Student B is correct** if the drain current is held fixed (e.g., the device is biased by a current source) and the overdrive is increased by making W/L smaller. Then $g_m = 2I_D/V_{ov}$ falls as $V_{ov}$ grows. This is the trade-off analog designers care about: for a given bias current, a small overdrive (large W/L) gives large $g_m$, which is why low-$V_{ov}$ operation is favored for gain and efficiency.\n\nSo the statement \"g_m goes up (or down) with overdrive\" is incomplete on its own. If you assume a fixed device with a swept gate voltage — the default interpretation — Student A wins. (In real short-channel devices, velocity saturation also makes $g_m$ flatten out at large overdrive, but that's a second-order effect beyond the square-law model.)",
        "format": "markdown",
        "sha256": "3e948ed7309482555fffcbce8546044d002c1a5b45564ab35841ab7243bed6e2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed device size and explains that raising overdrive raises current and gm. It also correctly notes that Student B's conclusion applies at fixed drain current when W/L is reduced; the short-channel caveat is secondary.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1525,
        "total_tokens": 1579,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 955,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1525,
        "total_tokens": 1579,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 955,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Both can be right — the question is incomplete until you say what is being held constant.**\n\nIn saturation (square‑law model), the drain current is\n\nI_D = ½ μₙC_ox (W/L) V_ov²  with V_ov = V_GS − V_T,\n\nso the transconductance g_m = ∂I_D/∂V_GS can be written three equivalent ways:\n\ng_m = μₙC_ox (W/L) V_ov = 2I_D / V_ov = √(2 μₙC_ox (W/L) I_D)\n\n**Student A is correct if W/L is fixed.**\nTake a given transistor and raise V_GS. V_ov goes up, I_D goes up as V_ov², and g_m = μₙC_ox(W/L)·V_ov rises linearly. Graphically: the I_D–V_GS parabola gets steeper as you move up it.\n\n**Student B is correct if I_D is fixed.**\nSuppose a current source forces the same I_D, and you choose a device that operates at higher V_ov (i.e., a smaller W/L). Then g_m = 2I_D / V_ov falls as 1/V_ov. For the same current, a wider device with small overdrive has more transconductance. This is why analog designers talk about \"transconductance efficiency,\" g_m/I_D = 2/V_ov — it is highest at low overdrive (and highest of all in subthreshold).\n\nSo: g_m increases with V_ov at constant size, decreases with V_ov at constant current. Neither student is wrong; each has silently fixed a different variable.\n\n(One extra wrinkle: in short‑channel devices with velocity saturation, g_m tends toward W·C_ox·v_sat, nearly independent of V_ov, so at high overdrive neither trend is strong.)",
        "format": "markdown",
        "sha256": "70239feae3ab155fb3fa8dd19d2a33e99512b9a029327878e85883f9b3f576c4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed transistor size and explains that increasing overdrive raises current and gm. The fixed-current qualification for Student B is also correct; the additional short-channel note does not undermine the central answer.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1740,
        "total_tokens": 1794,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1161,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1740,
        "total_tokens": 1794,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1161,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Both can be right — they're implicitly holding different things constant.** The square-law model gives three equivalent expressions for the saturation-region transconductance:\n\n$$g_m = \\mu_n C_{ox}\\frac{W}{L}V_{OV} \\;=\\; \\frac{2I_D}{V_{OV}} \\;=\\; \\sqrt{2\\mu_n C_{ox}\\frac{W}{L}I_D}$$\n\nwhere $V_{OV} = V_{GS} - V_{TH}$.\n\n**Student A's case – W/L fixed:** If you take a given transistor and simply raise $V_{GS}$, the overdrive increases, the drain current increases quadratically, and $g_m = \\mu_n C_{ox}(W/L)V_{OV}$ increases linearly. Transconductance goes *up*.\n\n**Student B's case – $I_D$ fixed:** In real analog circuits the bias current is usually set by a current source. If you then increase $V_{OV}$ (by using a narrower device, i.e., smaller $W/L$, to force the same current through a smaller transistor), then $g_m = 2I_D/V_{OV}$ *decreases*. For a fixed current, a small overdrive gives more transconductance per amp — which is why designers often bias with modest $V_{OV}$ (a couple hundred mV) to get good $g_m/I_D$ efficiency.\n\nSo the question \"does $g_m$ increase or decrease with $V_{OV}$?\" is incomplete until you say what else is being held constant. The apparent contradiction between the first two formulas disappears once you notice that $I_D$ itself depends on $V_{OV}$ in the first case, while $W/L$ depends on it in the second.\n\n(One footnote: in short-channel devices, velocity saturation and mobility degradation make $g_m$ eventually level off with $V_{OV}$ even at fixed $W/L$, so Student A's trend weakens at large overdrives.)",
        "format": "markdown",
        "sha256": "c415c0036318d9148102df4f3e13cd12ea02624b54209325e27743663cfb9132"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed device size and explains that increasing overdrive raises current and gm. It also accurately states Student B’s fixed-current condition; the short-channel note is secondary.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1572,
        "total_tokens": 1626,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 54,
        "output_tokens": 1572,
        "total_tokens": 1626,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes.** The small‑signal model of a PMOS transistor is identical to that of an NMOS transistor – same topology, same orientation of the dependent sources (g<sub>m</sub>v<sub>gs</sub> and g<sub>mb</sub>v<sub>bs</sub> pointing from drain to source), same r<sub>o</sub> between drain and source, and the same capacitances (C<sub>GS</sub>, C<sub>GD</sub>, C<sub>SB</sub>, C<sub>DB</sub>, C<sub>GB</sub>). Only the *numerical values* of the parameters differ (e.g., g<sub>m</sub> is smaller for the same W/L and current because μ<sub>p</sub> < μ<sub>n</sub>, and λ, γ, and the capacitances have different values).\n\n**Why it works:** the small-signal model does not represent the DC currents and voltages; it represents the *derivatives* of the terminal currents with respect to the terminal voltages at the bias point. If we keep the NMOS sign conventions for the PMOS (I<sub>D</sub> defined from drain to source, V<sub>GS</sub> = V<sub>G</sub> − V<sub>S</sub>, etc.):\n\n- For a PMOS, I<sub>D</sub> and V<sub>GS</sub> are both negative. If V<sub>GS</sub> is made less negative (a positive increment v<sub>gs</sub>), the device turns off slightly, |I<sub>D</sub>| decreases, so I<sub>D</sub> (a negative number) *increases*. Hence ∂I<sub>D</sub>/∂V<sub>GS</sub> = g<sub>m</sub> > 0 – the same sign as for NMOS.\n- Likewise, making V<sub>DS</sub> less negative lowers |I<sub>D</sub>| through channel-length modulation, so ∂I<sub>D</sub>/∂V<sub>DS</sub> > 0 and r<sub>o</sub> is positive, just as in NMOS.\n- Raising V<sub>BS</sub> increases |V<sub>THP</sub>|, reducing |I<sub>D</sub>|, so ∂I<sub>D</sub>/∂V<sub>BS</sub> = g<sub>mb</sub> > 0, again the same polarity.\n\nIntuitive check: a negative v<sub>gs</sub> (gate pulled down, PMOS driven harder) gives g<sub>m</sub>v<sub>gs</sub> < 0 in the drain‑to‑source direction, i.e., *more* current from source to drain – exactly what a PMOS does.\n\nSo in small-signal analysis you can draw the same equivalent circuit for both device types and just insert the appropriate parameter values. It is only the *large-signal* models that differ (current direction, voltage polarities, the \"upside‑down\" orientation of the PMOS).",
        "format": "markdown",
        "sha256": "f8711c62afcf25f2c754d2feac347f2360e99f3b008ac5ef08724d68c4c2c0c4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form as the NMOS model. Its added polarity discussion is consistent with the stated source-referenced voltage and drain-to-source current conventions.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 5373,
        "total_tokens": 5408,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4392,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 5373,
        "total_tokens": 5408,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4392,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes — the small‑signal model (its topology and the sign conventions) is identical for PMOS and NMOS.** Only the numerical values of the parameters differ.\n\n**Why the model is the same**\n\nIn a PMOS, two things are reversed relative to an NMOS: the direction of the drain current (source → drain instead of drain → source) and the polarity of the controlling voltage (the device turns on with negative V_GS). These two reversals cancel in the linearized model.\n\n- NMOS: current flowing D→S increases with V_GS, so the small‑signal current source is i_d = g_m·v_gs directed from drain to source.\n- PMOS: current flowing S→D increases with V_SG, so i_sd = g_m·v_sg = −g_m·v_gs. A current of −g_m·v_gs from S to D is exactly the same thing as a current of +g_m·v_gs from D to S.\n\nSo the same voltage‑controlled current source g_m·v_gs (from drain to source) describes both devices. The same argument holds for the other elements:\n\n- r_o: ∂I_SD/∂V_SD > 0 for PMOS is equivalent to ∂I_DS/∂V_DS > 0, so r_o is just a positive resistor between D and S, as in NMOS.\n- g_mb·v_bs: raising V_BS increases |V_TH| in a PMOS, reducing I_SD, which is the same as increasing I_DS — the same sign as the NMOS body‑effect source.\n- Capacitances C_GS, C_GD, C_GB, C_SB, C_DB appear in the same places.\n\n**What does differ**\n\n- Parameter values: μ_p is typically 2–4× smaller than μ_n, so for the same W/L and I_D a PMOS has lower g_m (and higher f_T limits); λ, γ, V_TH magnitude and the junction capacitances also differ.\n- Practical details: in an n‑well process the PMOS body is a separate n‑well node (often tied to the source, eliminating g_mb, but adding an n‑well–to‑substrate capacitance), whereas all NMOS devices share the common substrate.\n\nIn short: same model, same signs — just plug in different numbers.",
        "format": "markdown",
        "sha256": "0b3126f1886683ebb7eea6879e994f5d2f56841598b21060448cac73fcaa0c85"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form as the NMOS model, satisfying the golden solution’s explicit full-credit rule.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 2891,
        "total_tokens": 2926,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2168,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 2891,
        "total_tokens": 2926,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2168,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes.** The small‑signal (incremental) model of a PMOS transistor is identical to that of an NMOS transistor – same topology, same element orientations – even though the large‑signal currents and voltages have opposite polarities.\n\n**Why the polarities don't flip the model**\n\nTake the dependent current source g_m·v_gs, which in the NMOS model points from drain to source:\n\n- **NMOS:** I_D flows drain → source. Raising V_GS by Δv increases I_D by g_m·Δv, i.e., extra current g_m·Δv flows drain → source.\n- **PMOS:** |I_D| flows source → drain. Raising V_GS by Δv (making it *less negative*, so |V_GS| shrinks) *reduces* the source → drain current by g_m·Δv. A decrease of g_m·Δv in the source → drain direction is exactly the same as an increment of g_m·Δv flowing drain → source.\n\nSo in both cases a positive v_gs produces an incremental current g_m·v_gs from drain to source – the controlled source has the same direction. The same argument holds for the body‑effect source g_mb·v_bs, and r_o (between drain and source) and the capacitances (C_GS, C_GD, C_SB, C_DB, C_GB) are unaffected by polarity.\n\n**What does differ**\n\nOnly the numerical values: g_m, g_mb, r_o, V_TH, μC_ox, etc. For example, g_m = μ_p C_ox (W/L)(|V_GS| − |V_TH|) is typically smaller for a PMOS of the same size because μ_p < μ_n. The bias point is set with reversed polarities (V_GS, V_DS negative, body at the highest potential), but once the operating point is established, the same small‑signal circuit is used for both devices.",
        "format": "markdown",
        "sha256": "fb3a61d07bc862c54c755432bdc94dad936342a66d621534ec437f0db0f33de0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form as the NMOS model and explains how consistent source-referenced voltage and current polarities give the same controlled-source direction.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 1840,
        "total_tokens": 1875,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1245,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 35,
        "output_tokens": 1840,
        "total_tokens": 1875,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1245,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the circuit**\n\nM1 is \"diode‑connected\": gate and drain are tied together, source is grounded. Therefore\n\nV_GS = V_DS = V_X\n\n**Region of operation**\n\n- For V_X < V_TH: V_GS < V_TH → M1 is off, I_X = 0.\n- For V_X > V_TH: since V_DS = V_GS > V_GS − V_TH always, the transistor can **never** enter the triode region. It is always in **saturation** as soon as it turns on.\n\n**I_X – V_X relationship**\n\n$$\nI_X =\n\\begin{cases}\n0, & V_X < V_{TH}\\\\[2mm]\n\\dfrac{1}{2}\\mu_n C_{ox}\\dfrac{W}{L}\\,(V_X - V_{TH})^2, & V_X \\ge V_{TH}\n\\end{cases}\n$$\n\n(If channel‑length modulation is included, multiply by (1 + λV_X), which only bends the curve slightly upward.)\n\n**Sketch**\n\n```\n I_X\n  |                                   .\n  |                                 .\n  |                               .\n  |                             .\n  |                          .\n  |                       .\n  |                   .\n  |              .  \n  |_________._______________________________ V_X\n  0        V_TH\n```\n\n- I_X = 0 (flat along the axis) up to V_X = V_TH.\n- At V_X = V_TH the current starts from zero with zero slope and then rises as a **parabola** (square law) in V_X − V_TH — exactly like the I_D–V_GS characteristic of a MOSFET in saturation, which is why the diode‑connected device behaves like a (square‑law) \"diode.\"\n- The small-signal slope at any point is g_m = μ_nC_ox(W/L)(V_X − V_TH), i.e., the device looks like a resistance 1/g_m.",
        "format": "markdown",
        "sha256": "337be5a8ec606603ef6031856f92256dc59d68693a2983d68aee228efd654e12"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, its saturation operation above threshold, and the zero-below-threshold, quadratic-above-threshold current. The optional channel-length-modulation and small-signal comments do not affect the result.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1540,
        "total_tokens": 2846,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 928,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1540,
        "total_tokens": 2846,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 928,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the circuit**\n\nM1 is \"diode‑connected\": its gate is tied to its drain, and its source is grounded. Therefore\n\n- V_GS = V_DS = V_X \n- I_X = I_D (the current entering the drain)\n\n**Region of operation**\n\n- **V_X < V_TH:** V_GS < V_TH, so the transistor is off → I_X = 0. \n (For V_X < 0 the device is still off: the V_X terminal would become the \"source,\" giving V_GS = 0.)\n\n- **V_X > V_TH:** Since V_DS = V_GS, we always have V_DS > V_GS − V_TH, so the device is **always in saturation** (never in the triode region). Hence\n\n I_X = ½ μₙC_ox (W/L) (V_X − V_TH)²\n\n (or ½ μₙC_ox (W/L)(V_X − V_TH)²(1 + λV_X) if channel‑length modulation is included).\n\n**Sketch**\n\n```\n I_X\n  ^\n  |                               /\n  |                              /\n  |                             /\n  |                           /        I_X = ½ μnCox(W/L)(V_X − V_TH)²\n  |                         /\n  |                      _/\n  |                   _-'\n  |     I_X = 0  __--'\n  |_____________/\n  +------------+---------------------------> V_X\n  0           V_TH\n```\n\n- The curve is zero up to V_X = V_TH.\n- Beyond V_TH it rises as a parabola (a square‑law curve) starting with zero slope at V_TH.\n- The slope at any point is dI_X/dV_X = μₙC_ox(W/L)(V_X − V_TH) = g_m, i.e., the diode‑connected device behaves as a small‑signal resistance of 1/g_m.\n- With λ ≠ 0 the curve bends up slightly more steeply, but the shape is essentially the same.",
        "format": "markdown",
        "sha256": "569045e04578365c1748f533283847adf6cecd8befe33eaf794b1a007bad6af7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, its off region and saturation above threshold, and the resulting quadratic rise in IX. The negative-VX body-junction behavior is secondary and does not affect the essential answer.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1673,
        "total_tokens": 2979,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1043,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1673,
        "total_tokens": 2979,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1043,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the circuit**\n\nM1 is an NMOS device with its gate tied to its drain (\"diode‑connected\"), source grounded, and the test source VX applied at the drain/gate node. Therefore\n\nVGS = VDS = VX\n\n**Region of operation**\n\n- **VX < VTH:** VGS < VTH, so the channel is not formed → IX = 0. (For VX < 0 the terminal at ground becomes the drain and the terminal at VX becomes the source, giving VGS = 0 < VTH, so the device is still off → IX = 0.)\n\n- **VX > VTH:** The device turns on. Since VDS = VGS, we always have VDS > VGS − VTH, so M1 is **in saturation** for every VX > VTH (it can never enter the triode region). Hence\n\n$$I_X=\\frac{1}{2}\\mu_nC_{ox}\\frac{W}{L}\\,(V_X-V_{TH})^2$$\n\nor, with channel‑length modulation,\n\n$$I_X=\\frac{1}{2}\\mu_nC_{ox}\\frac{W}{L}(V_X-V_{TH})^2(1+\\lambda V_X)$$\n\n**Sketch**\n\n```\n IX\n  |                              .\n  |                            .\n  |                          .\n  |                        .\n  |                      .\n  |                    .\n  |                  .\n  |               .\n  |            .\n  |       . .\n  |_______________________________ VX\n  0      VTH\n```\n\nIX is zero (flat along the axis) for all VX below VTH, and then rises as a parabola with its vertex at VX = VTH. The result looks like a diode characteristic, except the turn‑on is quadratic rather than exponential – which is exactly why this configuration is called a \"diode‑connected\" MOSFET.",
        "format": "markdown",
        "sha256": "414158067427f0d4d39906af8ad5bf7d08cfe7c6e94df434184b5f84c060ccb7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "The essential sketch is correct: IX is approximately zero below threshold and rises quadratically above it, with the diode-connected NMOS in saturation. The extra claim of zero current for all negative VX overlooks body-junction conduction at sufficiently negative voltages, but that topic is secondary to the required result.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1460,
        "total_tokens": 2766,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 877,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1306,
        "output_tokens": 1460,
        "total_tokens": 2766,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 877,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the circuit**\n\n- Source of M1 is grounded, gate is at VX → VGS = VX  \n- Drain is tied to the 1 V battery → VDS = 1 V (fixed)  \n- IX is simply the drain current ID.\n\nBecause VDS is fixed, sweeping VX moves the transistor through three regions:\n\n**1. VX < VTH (cutoff)**\n\nIX = 0\n\n**2. VTH < VX < VTH + 1 V (saturation)**\n\nHere VDS = 1 V > VGS − VTH = VX − VTH, so M1 is saturated:\n\nIX = ½ μnCox (W/L)(VX − VTH)²\n\n→ IX rises as a parabola starting from zero at VX = VTH.\n\n**3. VX > VTH + 1 V (triode)**\n\nNow VGS − VTH > VDS = 1 V, so M1 enters the triode region:\n\nIX = μnCox (W/L)[(VX − VTH)(1 V) − ½(1 V)²]\n  = μnCox (W/L)(1 V)·(VX − VTH − 0.5 V)\n\n→ IX becomes a straight line with constant slope μnCox(W/L)(1 V).\n\n**Transition point**\n\nAt VX = VTH + 1 V both expressions give IX = ½ μnCox (W/L)(1 V)², and the slopes also match (the derivative of the saturation parabola there is μnCox(W/L)(1 V)), so the curve is smooth.\n\n**Sketch**\n\n```\n IX\n  ^\n  |                                   /\n  |                                  /   triode (straight line,\n  |                                 /    slope = μnCox(W/L)·1V)\n  |                                /\n  |                              .'\n  |                            .'\n  |  ½μnCox(W/L)(1V)² - - - -.'\n  |                        .'  saturation (parabola)\n  |                      .'\n  |                   .'\n  |   IX = 0      _.-'\n  +-----------==='--------+-----------------> VX\n  0           VTH      VTH + 1 V\n```\n\nZero until VX reaches VTH, a quadratic rise while the device is saturated, and then a linear rise (constant slope) once VX exceeds VTH + 1 V and the device enters the triode region. (If channel-length modulation is included, the saturation portion is scaled by the constant factor (1 + λ·1 V), which does not change the shape.)",
        "format": "markdown",
        "sha256": "8361cc4e87641ee61fca2d357aa97c101215af06cebbf25b3119844b7a7f997e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the cutoff, quadratic saturation rise, and transition to a roughly linear triode-region rise at VX = VTH + 1 V, with appropriate current expressions.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 2024,
        "total_tokens": 3485,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1230,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 2024,
        "total_tokens": 3485,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1230,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the circuit**\n\nM1 has its source grounded, its gate at V_X, and its drain held at a constant V_DS = 1 V. I_X is simply the drain current of M1 as a function of V_GS = V_X.\n\n**Region 1 – Cutoff (V_X < V_TH)**\n\nNo channel exists, so\n\n  I_X = 0\n\n**Region 2 – Saturation (V_TH < V_X < V_TH + 1 V)**\n\nThe device is saturated as long as V_DS ≥ V_GS − V_TH, i.e. V_X − V_TH ≤ 1 V. Then\n\n  I_X = ½ μnCox (W/L)(V_X − V_TH)²  [× (1 + λ·1 V) if channel‑length modulation is included]\n\nI_X rises *parabolically* (square‑law) with V_X.\n\n**Region 3 – Triode (V_X > V_TH + 1 V)**\n\nOnce V_X − V_TH exceeds V_DS = 1 V, M1 enters the triode region:\n\n  I_X = μnCox (W/L)[(V_X − V_TH)(1 V) − ½(1 V)²]\n    = μnCox (W/L)[(V_X − V_TH) − 0.5] (volts)\n\nThis is a *straight line* in V_X with constant slope μnCox(W/L)·(1 V).\n\nCheck at the boundary V_X = V_TH + 1 V: both expressions give I_X = ½ μnCox(W/L)·(1 V²), and both slopes equal μnCox(W/L)·(1 V), so the curve and its slope are continuous.\n\n**Sketch**\n\n```\n I_X\n  ^\n  |                                   /  ← linear (triode), slope = μnCox(W/L)(1 V)\n  |                                 /\n  |                               /\n  |                             /\n  |                          _/\n  |                       _-'\n½μnCox(W/L)(1V²) ·······_-'           ← transition point (slope continuous)\n  |                 _.-'\n  |            _..-'      ← parabola (saturation), ½μnCox(W/L)(V_X−V_TH)²\n  |________..-'\n  +-------------+-----------+------------------------> V_X\n  0           V_TH      V_TH + 1 V\n```\n\n- Zero current up to V_TH,\n- quadratic increase between V_TH and V_TH + 1 V (saturation),\n- linear increase (constant slope) beyond V_TH + 1 V (triode).",
        "format": "markdown",
        "sha256": "09c12e555d112100f1ea1bf038db546dcbd9eafd5509e22f049ad7940af9a14b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the cutoff, saturation, and triode regions and gives the required quadratic rise up to V_TH + 1 V followed by a roughly linear rise. The optional channel-length-modulation note does not affect the main result.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 1654,
        "total_tokens": 3115,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 836,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 1654,
        "total_tokens": 3115,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 836,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the problem**\n\nFor M1: the source is grounded, the gate is at V_X, and the drain is held at 1 V. Hence\n\n- V_GS = V_X\n- V_DS = 1 V (constant)\n- I_X = I_D\n\nBecause V_DS is fixed, the operating region is decided by V_X alone:\n\n| Region | Condition | I_X |\n|---|---|---|\n| Off | V_X < V_TH | I_X = 0 |\n| Saturation | V_TH < V_X < V_TH + 1 V (i.e. V_DS ≥ V_GS − V_TH) | I_X = ½ μ_nC_ox (W/L)(V_X − V_TH)² |\n| Triode | V_X > V_TH + 1 V (i.e. V_DS < V_GS − V_TH) | I_X = μ_nC_ox (W/L)[(V_X − V_TH)(1 V) − ½(1 V)²] = μ_nC_ox (W/L)(1 V)(V_X − V_TH − 0.5 V) |\n\n**Checking the boundary (V_X = V_TH + 1 V)**\n\n- Saturation: I_X = ½ μ_nC_ox (W/L)(1 V)²\n- Triode: I_X = μ_nC_ox (W/L)(1 V)(0.5 V) = ½ μ_nC_ox (W/L)(1 V)²  ✓\n\nSlopes also match there: dI_X/dV_X = μ_nC_ox(W/L)(1 V) in both regions, so the curve is smooth.\n\n**Sketch**\n\n```\n I_X\n  ^\n  |                                   /   <- triode: straight line,\n  |                                 /        slope = μnCox(W/L)·(1 V)\n  |                               /\n  |  ½μnCox(W/L)(1V)² - - - - - •\n  |                           /  \n  |                         /   <- saturation: parabola\n  |                       /        ½μnCox(W/L)(Vx−VTH)²\n  |                    _/\n  |     I_X = 0   ___-\n  +-------------•-------------•------------------> V_X\n  0            VTH         VTH + 1 V\n```\n\n- For V_X < V_TH the device is off and I_X = 0.\n- From V_TH to V_TH + 1 V the current rises **quadratically** (saturation).\n- Beyond V_TH + 1 V the drain-source voltage (1 V) is less than the overdrive, the device goes into the **triode** region, and I_X increases only **linearly** with V_X, with slope μ_nC_ox(W/L)·(1 V); the extrapolated straight line crosses the V_X axis at V_TH + 0.5 V.\n\n(If channel-length modulation is included, the saturation portion is simply scaled by the constant factor (1 + λ·1 V); the shape of the plot is unchanged.)",
        "format": "markdown",
        "sha256": "10d3f01323ae31f72c2b0fdef25415f25abf24f9a93a9edbc1e6018647d95f5d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the off, saturation, and triode regions, with the required quadratic rise up to V_TH + 1 V and roughly linear rise beyond. The boundary values and slopes are also consistent.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 2056,
        "total_tokens": 3517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1103,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1461,
        "output_tokens": 2056,
        "total_tokens": 3517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1103,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.**\n\n**Identify the terminals.** The arrow points *into* the device, so this is a PMOS transistor whose source is the top terminal (the node where I_X enters, call its voltage V_X). The gate and the drain are both tied to ground.\n\n**Analyze.** Because gate and drain are shorted (both at 0 V), the transistor is \"diode‑connected\":\n\n- V_SG = V_X − 0 = V_X  \n- V_SD = V_X − 0 = V_X  \n\nFor V_X > |V_THP| the device conducts, and since V_SD = V_SG > V_SG − |V_THP| it is in saturation. However, the gate‑source voltage is *not* fixed – it is the very voltage across the two‑terminal device. Thus\n\nI_X = ½ μ_p C_ox (W/L)(V_X − |V_THP|)² (1 + λV_X)\n\nwhich depends strongly (quadratically) on V_X.\n\n**Conclusion.** A current source must deliver a current essentially independent of the voltage across it, which for a MOSFET requires a *constant* V_GS (the source at a fixed potential and the gate at a fixed bias), with the drain as the output terminal. Here the floating terminal is the source, so V_SG changes with V_X and the current follows V_X. The circuit therefore behaves as a nonlinear resistor/diode (small‑signal impedance ≈ 1/g_m), not as a (high‑impedance) current source.\n\nTo obtain a PMOS current source, tie the source to V_DD, apply a constant bias V_b to the gate, and take the current from the drain: I_D ≈ ½ μ_p C_ox (W/L)(V_DD − V_b − |V_THP|)², roughly independent of the drain voltage while the device stays in saturation.",
        "format": "markdown",
        "sha256": "83a8ec321a842a64c5a629619cfaedcb3025918b3ba1b5448483b4974ef5e72d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS with source at the top and gate and drain grounded, and explains that its diode-connected low impedance (about 1/gm) makes it a nonlinear resistor rather than a current source.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 7520,
        "total_tokens": 8098,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6930,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 7520,
        "total_tokens": 8098,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6930,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.**\n\nLook at how the terminals are connected. The device is a PMOS whose source is the top node (where I_X enters) and whose gate and drain are both grounded. Call the voltage of the top node V_X. Then\n\n- V_SG = V_X − 0 = V_X  \n- V_SD = V_X − 0 = V_X  \n\nSince V_SD = V_SG > V_SG − |V_TH|, M1 is in saturation (as long as V_X > |V_TH|; otherwise it is simply off), and\n\nI_X = ½ μ_p C_ox (W/L)(V_X − |V_TH|)² (×(1+λV_X) if channel‑length modulation is included).\n\nA current source must deliver a current that is (nearly) independent of the voltage across it, i.e., it must present a very high impedance at its output node. Here the current is a strong (quadratic) function of V_X, and the impedance seen looking into the top node is only about 1/g_m (in parallel with r_O). In fact, with the gate tied to the drain this is just a diode‑connected PMOS – it behaves like a diode/nonlinear resistor, not a current source.\n\nThe general point: a MOSFET acts as a current source only when the output is taken from the *drain* with a fixed V_GS. The source cannot be the output node, because the source potential sets V_GS and therefore the current itself.",
        "format": "markdown",
        "sha256": "fe155ce5046bd43fc3a3120241c9a7fdbda10ae3a867174beb74d516bbc23fc9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a diode-connected PMOS with its source at the top node and gate/drain grounded, and explains that its low output impedance (about 1/gm) means it cannot act as a current source.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 5639,
        "total_tokens": 6217,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5195,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 5639,
        "total_tokens": 6217,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5195,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.**\n\nLook at which terminal is which. The arrow is on the top terminal and points into the device, so this is a **PMOS** whose **source** is the node that carries *I_X*, while the **gate and drain are both tied to ground**. Gate and drain shorted together means the transistor is *diode‑connected*.\n\nConsequences:\n\n- The voltage across the device is the source voltage V_X, so  \n  V_SG = V_SD = V_X.  \n  The device is in saturation whenever it conducts (V_SD = V_SG > V_SG − |V_TH|), but\n\n  I_X = ½ μ_p C_ox (W/L) (V_X − |V_TH|)² (1 + λV_X)\n\n- The current is therefore a strong (square‑law) function of the voltage across the two terminals.\n\nFor a MOSFET to behave as a current source, its gate–source voltage must be held constant while the drain voltage swings; then I_D is almost independent of V_DS (output impedance ≈ r_O). Here the terminal whose voltage changes is the *source*, so V_SG changes directly with V_X and the current follows it. The structure is simply a two‑terminal nonlinear resistor (\"MOS diode\") with small‑signal impedance ≈ 1/g_m (‖ r_O), far too low to be considered a current source.",
        "format": "markdown",
        "sha256": "ce524fba1387312bc513c01b115b180a58aea7b6541950eb778c611c26266df3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS with source at the input and gate tied to drain at ground. It explains that the diode-connected device’s current varies with VX and its low small-signal impedance (about 1/gm) prevents it from acting as a current source.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 6159,
        "total_tokens": 6737,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5726,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 578,
        "output_tokens": 6159,
        "total_tokens": 6737,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5726,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Circuit identification**\n\nM₁ is a PMOS transistor with its source tied to V_DD through R_S, its gate driven by V_in, and its drain loaded by R_D to ground; the output is taken at the drain. This is a **PMOS common‑source (CS) stage with source degeneration** – the \"upside‑down\" counterpart of the familiar NMOS degenerated CS stage. (Razavi deliberately labels the resistors so that R_S is at the source and R_D at the drain.)\n\n---\n\n**1. DC (bias) analysis** (assume saturation, λ = 0)\n\nLet I_D flow from V_DD through R_S, M₁ and R_D to ground.\n\n- V_S = V_DD − I_D R_S  \n- V_SG = V_DD − I_D R_S − V_in  \n- I_D = ½ μ_pC_ox (W/L)(V_DD − I_D R_S − V_in − |V_TH|)²  → solve this quadratic for I_D  \n- V_out = I_D R_D  \n\nSaturation requires V_SD ≥ V_SG − |V_TH|, i.e. the drain may not go more than |V_TH| above the gate:\n\n V_DD − I_D(R_S+R_D) ≥ V_DD − I_DR_S − V_in − |V_TH| ⟹ **I_D R_D ≤ V_in + |V_TH|**\n\nTransconductance at this bias: g_m = μ_pC_ox(W/L)(V_SG − |V_TH|) = 2I_D /(V_SG − |V_TH|).\n\n---\n\n**2. Small‑signal analysis**\n\nThe small‑signal model of a PMOS is identical to that of an NMOS, and V_DD is an ac ground, so R_S appears between source and ground and R_D between drain and ground.\n\n- Source node: v_s = g_m(v_in − v_s)R_S ⟹ v_s = v_in · g_mR_S/(1+g_mR_S)  \n- Drain node: v_out = −g_m(v_in − v_s)R_D  \n\n$$\nA_v=\\frac{v_{out}}{v_{in}}=-\\frac{g_mR_D}{1+g_mR_S}=-\\frac{R_D}{\\dfrac{1}{g_m}+R_S}\n$$\n\nIncluding channel‑length modulation (r_O):\n\n$$\nA_v=-\\frac{g_m r_O R_D}{r_O+R_D+R_S+g_m r_O R_S}\n$$\n\n(If the n‑well is tied to V_DD rather than to the source, replace g_m R_S by (g_m+g_mb)R_S in the denominator – body effect lowers the gain slightly.)\n\n**Input impedance:** R_in = ∞ (gate, low frequency).\n\n**Output impedance:** R_out = R_D ∥ [r_O(1+g_mR_S)+R_S] ≈ R_D for λ = 0.\n\n---\n\n**3. Remarks**\n\n- The gain is **inverting**: a rise in V_in reduces V_SG, reduces I_D, and therefore reduces V_out = I_D R_D.\n- R_S trades gain for linearity and bias stability (I_D less sensitive to V_TH, μ_p, W/L). For g_mR_S ≫ 1, A_v → −R_D/R_S, independent of the transistor.\n- Without degeneration (R_S = 0) the circuit reduces to the ordinary PMOS CS stage with A_v = −g_mR_D (or −g_m(R_D ∥ r_O)).\n- The output swing is limited on the high side by the saturation condition above (V_out ≤ V_in + |V_TH|) and on the low side by V_out ≥ 0 (I_D → 0).",
        "format": "markdown",
        "sha256": "cec4ea58a6b9ff111feadafe78e1819f203b65cabbb17bd83e1eee0f3b2f2bcb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M₁ as a PMOS common-source stage with source degeneration and gives the inverting gain −gₘR_D/(1+gₘR_S), satisfying the full-credit rule.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 5006,
        "total_tokens": 6568,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3764,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 5006,
        "total_tokens": 6568,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3764,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nM1 is a **PMOS** transistor:\n\n- gate → input `Vin`\n- source → VDD through `RS`\n- drain → ground through `RD`, and this node is the output\n\nInput at the gate, output at the drain, source \"common\" (tied to the AC‑ground VDD through a resistor): this is a **common‑source (CS) stage with source degeneration**, simply the PMOS mirror image of the familiar NMOS degenerated CS stage (VDD and ground swapped, device flipped). Since the small‑signal model of a PMOS is identical to that of an NMOS, all NMOS results carry over directly.\n\nSign of the gain (intuition): if `Vin` rises, `VSG = VS − Vin` falls, `ID` falls, the drop `ID·RD` falls, so `Vout = ID·RD` falls → **inverting** amplifier.\n\n## 2. DC (large‑signal) operation\n\nKVL from VDD to the gate:\n\n$$V_{SG}=V_{DD}-I_D R_S-V_{in}$$\n\n- **Off:** `Vin > VDD − |VTH|` → `ID = 0`, `Vout = 0`.\n- **Saturation** (the useful region), with λ = 0:\n\n$$I_D=\\tfrac12\\mu_pC_{ox}\\tfrac{W}{L}\\big(V_{DD}-V_{in}-I_DR_S-|V_{TH}|\\big)^2 ,\\qquad V_{out}=I_DR_D$$\n\n  (a quadratic in `ID`; take the root that gives `VSG > |VTH|`).\n\n- **Saturation condition:** `VSD ≥ VSG − |VTH|`, i.e. `VD ≤ VG + |VTH|`:\n\n$$V_{out}=I_DR_D\\;\\le\\;V_{in}+|V_{TH}|$$\n\n  Headroom budget: `VDD = ID RS + VSD + ID RD`; both resistors eat supply voltage.\n\n- **Triode:** when `Vout` exceeds `Vin + |VTH|` (large `RD` or low `Vin`); eventually `Vout → VDD·RD/(RD+RS+Ron)`.\n\n`RS` also stabilizes the bias: if `ID` tries to increase, the drop across `RS` grows, `VSG` shrinks, and `ID` is pushed back (negative feedback).\n\n## 3. Small‑signal analysis\n\nSet VDD to AC ground. Then: gate = `vin`, source node has `RS` to ground, drain node has `RD` to ground — exactly the NMOS degenerated CS stage.\n\n**λ = 0:**\n\nLet `id = gm·vgs = gm(vin − vs)`, with `vs = id·RS` and `vout = −id·RD`:\n\n$$i_d=\\frac{g_m v_{in}}{1+g_mR_S}\\quad\\Rightarrow\\quad \n\\boxed{A_v=\\frac{v_{out}}{v_{in}}=-\\frac{g_mR_D}{1+g_mR_S}=-\\frac{R_D}{\\dfrac1{g_m}+R_S}}$$\n\ni.e. −(resistance at the drain)/(resistance in the source path). Stage transconductance `Gm = gm/(1+gm RS)`.\n\n- `Rin = ∞` (MOS gate, low frequency)\n- `Rout = RD` (with ro = ∞ the drain looks like an open circuit)\n\n**λ ≠ 0 (include ro):**\n\n$$A_v=-\\frac{g_m r_o R_D}{r_o+R_D+R_S+g_m r_oR_S},\\qquad\nR_{out}=R_D\\,\\big\\|\\,\\big[(1+g_mR_S)r_o+R_S\\big]$$\n\n(degeneration *raises* the resistance seen looking into the drain by the factor ≈ `1+gmRS`).\n\n**Body effect** (if the n‑well is tied to VDD rather than to the source): replace `gm RS` in the denominator by `(gm+gmb)RS`:  `Av = −gm RD / [1+(gm+gmb)RS]`. If the well is tied to the source, there is no body effect.\n\n## 4. Key observations\n\n| Quantity | λ = 0 result |\n|---|---|\n| Voltage gain | `−gm RD/(1+gm RS)` |\n| Input resistance | ∞ |\n| Output resistance | `RD` |\n| Saturation requirement | `ID RD ≤ Vin + |VTH|` |\n\n- Degeneration trades gain for linearity and robustness: for `gm RS ≫ 1`, `Av → −RD/RS`, nearly independent of the transistor (process, temperature, bias).\n- Without `RS` (RS = 0) the circuit reduces to a plain PMOS CS stage with `Av = −gm RD` (or `−gm (RD‖ro)`).\n- Both `RS` and `RD` consume headroom, so increasing them for gain/linearity eventually pushes M1 into triode (`Vout > Vin + |VTH|`).",
        "format": "markdown",
        "sha256": "65a856c71e06c57b974f1a158e740420e3a717d0cd87e319d8b7d9fc1b0e2da9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS common-source stage with source degeneration and gives the inverting gain −gmRD/(1 + gmRS). The additional body-effect and finite-ro discussion is consistent with the essential answer.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 11391,
        "total_tokens": 12953,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9681,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 11391,
        "total_tokens": 12953,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9681,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Circuit identification\n\nM₁ is a **PMOS** device whose source goes to V_DD through R_S, whose gate is driven by V_in, and whose drain (the output node) is loaded by R_D to ground. Because the input is at the gate and the output is at the drain, this is a **common‑source (CS) amplifier with source degeneration** – it is simply the \"upside‑down\" (PMOS) version of the degenerated NMOS CS stage. (It is *not* a source follower: the output is taken at the drain, not at R_S.)\n\n---\n\n## 1. DC (bias) analysis\n\nLet the input have a dc component V_IN. One current I_D flows from V_DD through R_S, through M₁ (source→drain), and through R_D to ground:\n\n- Source voltage: V_S = V_DD − I_D R_S  \n- Gate–source overdrive: V_SG = V_DD − I_D R_S − V_IN  \n- In saturation (λ ≈ 0):\n\n$$I_D=\\tfrac12\\mu_pC_{ox}\\frac{W}{L}\\bigl(V_{DD}-I_DR_S-V_{IN}-|V_{TH}|\\bigr)^2$$\n\n(solve the quadratic; keep the root with V_SG > |V_TH|.)\n\n- Output dc level: V_out,DC = I_D R_D  \n- Saturation requirement: V_SD ≥ V_SG − |V_TH| ⟺ V_D ≤ V_G + |V_TH| ⟺ **I_D R_D ≤ V_IN + |V_TH|**  \n- Headroom: V_DD = I_D R_S + V_SD + I_D R_D\n\nR_S provides negative feedback on the bias point: if I_D tends to rise, V_S drops, V_SG shrinks, and I_D is pulled back, so the bias is less sensitive to V_TH, μ_pC_ox, and temperature.\n\n---\n\n## 2. Small‑signal analysis\n\nSet V_DD to ac ground. The PMOS small‑signal model is identical to that of an NMOS, so the ac circuit is exactly a degenerated CS stage: R_S from source to ac ground, R_D from drain to ac ground.\n\n### Voltage gain with λ = 0\n\nWith v_s = −i_d R_S (current from the V_DD node into the source) and i_d = g_m(v_s − v_in):\n\n$$i_d=\\frac{-g_m}{1+g_mR_S}\\,v_{in},\\qquad v_{out}=i_dR_D$$\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=-\\frac{g_mR_D}{1+g_mR_S}=-\\frac{R_D}{\\dfrac1{g_m}+R_S}}$$\n\n- Inverting amplifier.  \n- Degeneration lowers the gain from −g_mR_D toward −R_D/R_S (for g_mR_S ≫ 1), but linearizes the stage and desensitizes the gain to g_m.\n\n(Equivalently, A_v = −G_m R_out with G_m = g_m/(1+g_mR_S) and R_out = R_D.)\n\n### Voltage gain with λ ≠ 0 (include r_O)\n\n$$A_v=-\\frac{g_mr_OR_D}{r_O+R_D+R_S+g_mr_OR_S}\n=-\\frac{R_D}{\\dfrac1{g_m}+R_S+\\dfrac{R_D+R_S}{g_mr_O}}$$\n\nwhich reduces to the λ = 0 result as r_O → ∞.\n\n---\n\n## 3. Input and output impedances\n\n- **Input impedance:** R_in = ∞ (gate of the MOSFET, low frequency).  \n- **Output impedance:**  \n  - λ = 0: R_out = R_D  \n  - λ ≠ 0: R_out = R_D ∥ [ (1 + g_mR_S) r_O + R_S ]  \n  (degeneration \"boosts\" the transistor's own output resistance by the factor 1 + g_mR_S).\n\n---\n\n## 4. Remarks / design trade‑offs\n\n- Larger R_D → larger |A_v|, but V_out,DC = I_D R_D rises; M₁ leaves saturation when I_D R_D > V_IN + |V_TH|.  \n- Larger R_S → more stable bias and better linearity, but lower gain (|A_v| → R_D/R_S).  \n- If the bulk is tied to V_DD (usual n‑well PMOS), the source is not at the bulk potential, so body effect exists; including it, A_v ≈ −g_mR_D / [1 + (g_m + g_mb)R_S].  \n- Output signal is 180° out of phase with the input, as in any CS stage.",
        "format": "markdown",
        "sha256": "0006cea60883279b095a54582e3082ad4352d4f1bd10bd406f8621bea67b751d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the required inverting gain, −gₘR_D/(1+gₘR_S). The additional body-effect and finite-rₒ refinements are consistent.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 7423,
        "total_tokens": 8985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5834,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1562,
        "output_tokens": 7423,
        "total_tokens": 8985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5834,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis: NMOS Source Follower (Common‑Drain Stage)\n\n## 1. Topology identification\n- **Gate** = input $V_{in}$  \n- **Drain** = tied directly to $V_{DD}$ → at small‑signal (AC) ground  \n- **Source** = output node $V_{out}$, returned to ground through $R_S$\n\nBecause the drain is the terminal common to input and output (AC ground), this is a **common‑drain amplifier**, universally called a **source follower**. The output \"follows\" the input, shifted down by $V_{GS}$:\n\n$$V_{out} = V_{in} - V_{GS}$$\n\n## 2. Large‑signal (DC) behavior\n\n**Cut‑off:** For $V_{in} < V_{TH}$, $M_1$ is off, $I_D = 0$, so $V_{out} = 0$.\n\n**Conduction:** For $V_{in} > V_{TH}$, $M_1$ turns on and the drain current flows through $R_S$:\n\n$$I_D = \\frac{V_{out}}{R_S} = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}\\,(V_{in}-V_{out}-V_{TH})^2$$\n\nThis (quadratic) equation gives $V_{out}$ for any $V_{in}$; take the root for which $V_{GS} > V_{TH}$.\n\n**Operating region:** $V_{DS} = V_{DD}-V_{out}$ and $V_{GS}-V_{TH} = V_{in}-V_{out}-V_{TH}$. Saturation requires $V_{DS}\\ge V_{GS}-V_{TH}$, i.e.\n\n$$V_{DD} \\ge V_{in} - V_{TH}$$\n\nwhich holds for any $V_{in} \\le V_{DD}+V_{TH}$. So, unlike a common‑source stage, **$M_1$ never enters triode** for inputs within the supply range.\n\n**Transfer characteristic:** $V_{out}$ stays at 0 until $V_{in}=V_{TH}$, then rises almost linearly with slope slightly less than 1. The slope is below unity because as $V_{in}$ rises, $I_D$ rises, so $V_{GS}$ must grow (∝ $\\sqrt{I_D}$); additionally, body effect raises $V_{TH}$ as $V_{SB}=V_{out}$ increases:\n\n$$V_{TH} = V_{TH0} + \\gamma\\left(\\sqrt{2\\Phi_F + V_{out}} - \\sqrt{2\\Phi_F}\\right)$$\n\nBoth effects make the level shift $V_{GS}$ signal‑dependent → nonlinearity.\n\n## 3. Small‑signal voltage gain\n\nSmall‑signal model: $v_{gs} = v_{in} - v_{out}$; the controlled source $g_m v_{gs}$ flows from the drain (ground) into the source node; $R_S$ ties the source node to ground.\n\nKCL at the output:\n\n$$g_m (v_{in}-v_{out}) = \\frac{v_{out}}{R_S}\n\\;\\;\\Rightarrow\\;\\;\nA_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m R_S}{1+g_m R_S} = \\frac{R_S}{R_S + 1/g_m}$$\n\n**Intuition:** looking into the source of a MOSFET you see a resistance $1/g_m$, so the stage is a voltage divider between $1/g_m$ and $R_S$. The gain is positive (non‑inverting) and **always less than 1**, approaching 1 when $g_m R_S \\gg 1$.\n\n**Including body effect** ($g_{mb}v_{bs}$, with $v_{bs} = -v_{out}$):\n\n$$A_v = \\frac{g_m}{g_m + g_{mb} + 1/R_S}\n= \\frac{R_S \\,\\|\\, \\tfrac{1}{g_{mb}}}{\\left(R_S \\,\\|\\, \\tfrac{1}{g_{mb}}\\right) + \\tfrac{1}{g_m}}$$\n\nEven with $R_S\\to\\infty$ the gain is limited to $g_m/(g_m+g_{mb}) = 1/(1+\\eta)\\approx 0.8$–$0.9$.\n\n**Including channel‑length modulation:** $r_o$ sits between drain (AC ground) and source, i.e., in parallel with $R_S$:\n\n$$A_v = \\frac{g_m}{g_m + g_{mb} + 1/R_S + 1/r_o}$$\n\nBecause $g_m = \\mu_n C_{ox}\\frac{W}{L}(V_{GS}-V_{TH})$ varies with the signal, the gain itself varies with $V_{in}$ → distortion for large swings.\n\n## 4. Input and output impedance\n- **Input impedance:** infinite at low frequency (gate). At high frequency the input capacitance is only $C_{GD} + C_{GS}(1-A_v)$ — $C_{GS}$ is \"bootstrapped\" because both its terminals move together.\n- **Output impedance** (looking into the source, $v_{in}=0$):\n\n$$R_{out} = \\frac{1}{g_m}\\,\\Big\\|\\,\\frac{1}{g_{mb}}\\,\\Big\\|\\, r_o \\,\\Big\\|\\, R_S \\;\\approx\\; \\frac{1}{g_m}$$\n\nThis low output resistance is the main reason the circuit is used.\n\n## 5. Quick numerical example\nLet $V_{DD}=1.8$ V, $V_{in}=1.2$ V, $R_S=10$ kΩ, $\\mu_nC_{ox}W/L = 2$ mA/V², $V_{TH}=0.5$ V (ignore $\\gamma,\\lambda$):\n\n$$\\frac{V_{out}}{10\\text{k}} = (1\\text{ mA/V}^2)(0.7-V_{out})^2 \\;\\Rightarrow\\; 10V_{out}^2 - 15V_{out} + 4.9 = 0 \\;\\Rightarrow\\; V_{out}\\approx 0.48\\text{ V}$$\n\n$I_D \\approx 48\\ \\mu$A, $V_{GS}-V_{TH}\\approx 0.22$ V, $g_m \\approx 0.44$ mS, so $g_mR_S\\approx 4.4$:\n\n$$A_v \\approx \\frac{4.4}{5.4}\\approx 0.81,\\qquad R_{out}\\approx 2.3\\text{ k}\\Omega\\,\\|\\,10\\text{ k}\\Omega \\approx 1.9\\text{ k}\\Omega$$\n\n(Check: $V_{DS}=1.32$ V $> 0.22$ V → saturation ✓.)\n\n## 6. Summary of properties\n| Property | Source follower |\n|---|---|\n| Voltage gain | $\\approx g_mR_S/(1+g_mR_S) < 1$, non‑inverting |\n| Input resistance | very high |\n| Output resistance | low, $\\approx 1/g_m$ |\n| DC function | level shifter: $V_{out} = V_{in} - V_{GS}$ |\n| Output swing | $0$ to $\\approx V_{DD}-V_{GS}$ |\n| Operating region | saturation for all $V_{in}\\le V_{DD}+V_{TH}$ |\n\n**Uses:** voltage buffer / output stage (drives low‑impedance or capacitive loads), DC level shifting between stages.\n\n**Limitations:** gain < 1 and signal‑dependent (body effect + $g_m$ variation → nonlinearity), loses $V_{GS}$ of headroom, and driving a small $R_S$ with gain near unity requires large $g_m$ (large bias current). Replacing $R_S$ with a current source raises the gain toward $g_m/(g_m+g_{mb})$ and improves linearity.",
        "format": "markdown",
        "sha256": "a14ad2a0c875cbcca3d923a022d92ac8d980fc7cf24fc93950e90b432e017ed0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, gmRS/(1+gmRS), as required for full credit.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 8443,
        "total_tokens": 9709,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5769,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 8443,
        "total_tokens": 9709,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5769,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit identification\n\nThe drain of M₁ is tied directly to V_DD (an ac ground), the input drives the gate, and the output is taken from the source across R_S. This is a **common‑drain stage, better known as a source follower**. Its job is not to provide voltage gain but to act as a **voltage buffer / level shifter**: high input impedance, low output impedance, gain close to (but below) unity.\n\n---\n\n## 1. Large‑signal (DC) behavior\n\n**Region of operation.** Because V_D = V_DD ≥ V_G, we have V_DS ≥ V_GS > V_GS − V_TH. Hence whenever M₁ conducts it is automatically in **saturation** (as long as V_in ≤ V_DD + V_TH).\n\n**Input–output characteristic.**\n\n- For V_in < V_TH: M₁ is off, I_D = 0, so V_out = 0.\n- For V_in > V_TH: M₁ turns on and its current flows through R_S:\n\n$$\n\\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}\\,(V_{in}-V_{out}-V_{TH})^2\\,R_S = V_{out}\n$$\n\nWriting β = μₙC_ox(W/L), the solution is\n\n$$\nV_{out}=V_{in}-V_{TH}+\\frac{1}{\\beta R_S}-\\frac{\\sqrt{1+2\\beta R_S\\,(V_{in}-V_{TH})}}{\\beta R_S}\n$$\n\nInterpretation: the output \"follows\" the input with a level shift equal to V_GS,\n\n$$\nV_{out}=V_{in}-V_{GS},\\qquad V_{GS}=V_{TH}+\\sqrt{\\frac{2I_D}{\\beta}},\\quad I_D=\\frac{V_{out}}{R_S}\n$$\n\nSince I_D (and therefore the overdrive) grows with V_in, V_GS is not constant, so the characteristic starts at V_in = V_TH with zero slope and bends up toward a slope slightly less than 1. If the body is grounded, V_TH also rises with V_out (body effect, V_SB = V_out), which increases the level shift further and lowers the slope.\n\n---\n\n## 2. Small‑signal voltage gain\n\nSmall‑signal model: g_m v_gs and g_mb v_bs current sources plus r_o, all between drain (ac ground) and source. With v_gs = v_in − v_out and v_bs = −v_out, KCL at the output node gives\n\n$$\ng_m(v_{in}-v_{out})-g_{mb}v_{out}-\\frac{v_{out}}{r_o}=\\frac{v_{out}}{R_S}\n$$\n\n$$\n\\boxed{A_v=\\frac{v_{out}}{v_{in}}=\\frac{g_m}{g_m+g_{mb}+\\dfrac{1}{r_o}+\\dfrac{1}{R_S}}\n=\\frac{g_m\\,(R_S\\,\\|\\,r_o\\,\\|\\,1/g_{mb})}{1+g_m\\,(R_S\\,\\|\\,r_o\\,\\|\\,1/g_{mb})}}\n$$\n\nUseful special cases:\n\n- Neglecting channel‑length modulation (r_o → ∞):  \n  A_v = g_mR_S / [1 + (g_m + g_mb)R_S]\n- Also neglecting body effect:  \n  A_v = g_mR_S / (1 + g_mR_S) = R_S / (R_S + 1/g_m) < 1\n- Even with an ideal load (R_S → ∞):  \n  A_v → g_m/(g_m + g_mb) = 1/(1 + η), η = g_mb/g_m ≈ 0.1–0.3, so the gain tops out around 0.8–0.9 with a grounded body.\n\nThe same result follows from differentiating the large‑signal equation, noting that ∂V_TH/∂V_in = η·∂V_out/∂V_in, which is how the g_mb term appears.\n\nBecause g_m = β(V_in − V_out − V_TH) depends on the bias current, which itself varies with the signal, **the gain is signal‑dependent** — the source of the follower's nonlinearity. (With β R_S large, A_v = 1 − 1/√(1 + 2βR_S(V_in − V_TH)) when body effect is ignored.)\n\n---\n\n## 3. Input and output impedance\n\n- **Input impedance:** the gate draws no dc current, so R_in → ∞ at low frequencies (only C_GS, C_GD load the source at high frequency; C_GS is largely bootstrapped since v_gs ≈ (1 − A_v)v_in is small).\n\n- **Output impedance:** setting v_in = 0 and applying a test voltage v_x at the output:\n\n$$\n\\boxed{R_{out}=\\frac{1}{g_m}\\,\\Big\\|\\,\\frac{1}{g_{mb}}\\,\\Big\\|\\,r_o\\,\\Big\\|\\,R_S\\;\\approx\\;\\frac{1}{g_m}}\n$$\n\nLooking into the source of M₁ alone (without R_S): 1/(g_m + g_mb) ‖ r_o. This low (moderate) output resistance is the follower's main attraction.\n\n---\n\n## 4. Summary of properties and trade‑offs\n\n| Quantity | Result |\n|---|---|\n| Configuration | Common‑drain (source follower) |\n| M₁ operating region | Saturation whenever on |\n| DC relation | V_out = V_in − V_GS (level shift of one V_GS) |\n| Voltage gain | g_mR_S / [1 + (g_m + g_mb)R_S + R_S/r_o] < 1 |\n| Input resistance | ∞ |\n| Output resistance | 1/g_m ‖ 1/g_mb ‖ r_o ‖ R_S ≈ 1/g_m |\n| Phase | Non‑inverting |\n\n**Advantages:** high input impedance, low output impedance, no voltage inversion, wide bandwidth (little Miller multiplication of C_GS, left‑half‑plane zero at −g_m/C_GS).\n\n**Drawbacks:**\n1. **Nonlinearity** – I_D, hence g_m and V_GS, change with the signal; the body effect adds a V_out‑dependent V_TH. Replacing R_S with a current source keeps I_D constant and removes the first effect; using a PMOS follower with the body tied to the source (or a triple‑well NMOS) removes the body effect.\n2. **Voltage headroom** – the output is shifted down by V_GS and the drain‑source voltage V_DD − V_out must stay above the overdrive, limiting swing.\n3. **Gain < 1** and power consumption – it buffers but never amplifies.\n\nIn practice this stage is used as a buffer between a high‑impedance (high‑gain) stage and a low‑impedance load, or as a dc level shifter.",
        "format": "markdown",
        "sha256": "015c30f8af2ab5b591a2b8eecc6139925bc6ebbf194d3d5004982fb6a4d59265"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, including the required gm·RS/(1 + gm·RS) form under the stated ideal assumptions. The body-effect and output-resistance refinements are compatible with the analysis.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 6972,
        "total_tokens": 8238,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4652,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 6972,
        "total_tokens": 8238,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4652,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Source Follower (Common‑Drain Stage)\n\n## 1. Identifying the topology\n- Input is applied to the **gate**, the **drain is tied directly to V_DD** (an AC ground), and the output is taken from the **source**, which is loaded by R_S to ground.\n- Because the drain is common to input and output (in the small‑signal sense), this is a **common‑drain amplifier**, usually called a **source follower**: V_out \"follows\" V_in.\n\n## 2. Large‑signal (DC) behavior\n- M₁ is off for V_in < V_TH, so V_out = 0.\n- For V_in > V_TH, the output simply equals the input shifted down by one gate‑source voltage:\n\n  V_out = V_in − V_GS\n\n- The drain current must also flow through R_S, so V_out = I_D R_S with (saturation, λ = 0)\n\n  I_D = ½ μₙC_ox (W/L)(V_in − V_out − V_TH)²\n\n  Solving this quadratic (K = ½ μₙC_ox W/L):\n\n  V_out = V_in − V_TH − [√(1 + 4KR_S(V_in − V_TH)) − 1] / (2KR_S)\n\n- **Region of operation:** V_DS = V_DD − V_out and V_GS − V_TH = V_in − V_out − V_TH. Since V_in ≤ V_DD, we always have V_DS > V_GS − V_TH, so **M₁ can never enter the triode region** – it is either off or in saturation.\n- As V_in rises, I_D rises, so V_GS rises slightly; hence V_out rises a little *less* than V_in (gain < 1). The output is **non‑inverting**.\n\n## 3. Small‑signal analysis\nReplace V_DD by AC ground. Then r_o (drain‑to‑source) appears in parallel with R_S, and v_gs = v_in − v_out. KCL at the output (source) node:\n\ng_m(v_in − v_out) − v_out/r_o = v_out/R_S\n\n**Voltage gain**\n\nA_v = v_out/v_in = g_m(R_S‖r_o) / [1 + g_m(R_S‖r_o)] = (R_S‖r_o) / [(R_S‖r_o) + 1/g_m]\n\nWith λ = 0: **A_v = R_S / (R_S + 1/g_m) = g_mR_S/(1 + g_mR_S)**\n\n- Always **less than 1**, positive, and approaches unity when g_mR_S ≫ 1.\n- Intuitive view: a voltage divider between the resistance seen looking into the source (1/g_m) and the load R_S.\n- Including body effect (bulk grounded, so v_bs = −v_out) adds a g_mb term, equivalent to a resistor 1/g_mb from source to ground:\n\n  A_v = g_m / (g_m + g_mb + 1/r_o + 1/R_S) = g_m(R_S‖r_o‖1/g_mb) / [1 + g_m(R_S‖r_o‖1/g_mb)]\n\n**Input impedance:** R_in = ∞ (gate, at low frequency).\n\n**Output impedance** (set v_in = 0, apply v_x at the output): i_x = g_m v_x + v_x/r_o + v_x/R_S, so\n\nR_out = (1/g_m) ‖ r_o ‖ R_S   (‖ 1/g_mb with body effect) ≈ **1/g_m** — low.\n\n## 4. Illustrative numbers\nTake K = 1 mA/V² (e.g. μₙC_ox = 100 µA/V², W/L = 20), V_TH = 0.5 V, R_S = 1 kΩ, V_in = 1.5 V, λ = 0:\n- Overdrive = [√(1+4·1·1) − 1]/2 = 0.618 V → I_D = 0.382 mA → V_out = 0.382 V (= 1.5 − 0.5 − 0.618 ✓)\n- g_m = 2K·V_ov = 1.24 mA/V → 1/g_m ≈ 809 Ω\n- A_v = 1000/(1000 + 809) ≈ 0.55, R_out ≈ 809‖1000 ≈ 450 Ω\n\n## 5. Key properties and drawbacks\n- **Function:** a voltage buffer / level shifter — very high input impedance, low output impedance (~1/g_m), gain ≈ 1. Used to drive low‑impedance loads or to shift the DC level by V_GS.\n- **Nonlinearity:** with a resistive load, I_D (and therefore g_m) changes with the signal, so the gain depends on the input level (dA_v/dV_in > 0: gain = 1 − 1/√(1+4KR_S(V_in−V_TH))). Replacing R_S with a current source keeps I_D nearly constant, making the gain closer to 1 and more linear (though body effect still limits it to g_m/(g_m+g_mb)).\n- **Swing:** V_out ranges from 0 (M₁ off) up to about V_DD − V_GS.\n- **Speed:** C_gs sits between input and output with nearly equal voltages on both plates (\"bootstrapped\"), so the input capacitance is small and the output pole ≈ g_m/C_L is at high frequency — source followers are fast.\n- **Power/gain cost:** no voltage gain, and the DC level drop of V_GS consumes headroom; the gain is degraded by finite g_mR_S, r_o, and the body effect.",
        "format": "markdown",
        "sha256": "a93cc6cef6ad1651b332383b8806e4ba0fcf1d5f2b2dceaf2ae0880197cbb67d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, gmRS/(1 + gmRS). The added output-resistance and body-effect analysis is also consistent with the circuit.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 6042,
        "total_tokens": 7308,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4190,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1266,
        "output_tokens": 6042,
        "total_tokens": 7308,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4190,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Identifying the topology\n\n- The gate of M₁ is tied directly to V_DD → it sits at a fixed potential, i.e. it is an **AC ground**.\n- The input V_in drives the **source** (the terminal carrying the arrow – M₁ is an NMOS).\n- The output is taken at the **drain**, which is loaded by R_D to V_DD.\n\nInput at the source, output at the drain, gate grounded for signals ⇒ this is a **common‑gate (CG) stage** with the gate bias V_b = V_DD.\n\n## 2. DC (bias) analysis (λ = 0)\n\nWith V_G = V_DD and V_S = V_in:\n\n- V_GS = V_DD − V_in → M₁ is on only if V_in < V_DD − V_TH.\n- In saturation \n\n  I_D = ½ μₙC_ox (W/L)(V_DD − V_in − V_TH)²\n\n  V_out = V_DD − I_D R_D\n\n- Saturation condition: V_DS ≥ V_GS − V_TH ⇔ V_D ≥ V_G − V_TH ⇔ V_DD − I_D R_D ≥ V_DD − V_TH\n\n  **⇒ I_D R_D ≤ V_TH**\n\n  Because the gate is at V_DD, the drain can fall at most V_TH below V_DD before M₁ enters the triode region. This is the main limitation of this bias choice.\n\n- Large‑signal characteristic: V_in > V_DD − V_TH → M₁ off, V_out = V_DD. As V_in decreases, I_D rises and V_out drops (V_out moves in the *same* direction as V_in). At V_out = V_DD − V_TH, i.e. at V_in = V_DD − V_TH − √(2V_TH /(μₙC_ox(W/L)R_D)), M₁ enters triode.\n- Note the input source must sink the dc bias current I_D, and since V_S = V_in ≠ V_B, body effect is present in general.\n\n## 3. Small‑signal analysis\n\nGate grounded: v_gs = −v_in. The current entering the drain is g_m v_gs = −g_m v_in, so\n\nv_out = −R_D·(−g_m v_in)  ⇒  **A_v = v_out/v_in = +g_m R_D**\n\n(non‑inverting), with g_m = √(2μₙC_ox(W/L)I_D) = 2I_D/(V_GS − V_TH).\n\nCombining with the saturation limit: A_v = 2(I_D R_D)/(V_GS − V_TH) ≤ 2V_TH/(V_DD − V_in − V_TH), so the gain is capped by tying the gate to V_DD.\n\nRefinements:\n- With channel‑length modulation: A_v = (1 + g_m r_O)R_D /(R_D + r_O) ≈ g_m(R_D‖r_O)\n- With body effect: replace g_m by (g_m + g_mb)\n- With a source resistance R_S driving the input: A_v = R_D /(R_S + 1/g_m)\n\n## 4. Input and output impedances\n\n- **Input impedance** (looking into the source): R_in = 1/g_m (λ = 0), or 1/(g_m + g_mb); with r_O: R_in = (R_D + r_O)/(1 + g_m r_O). Low, as expected for a CG stage.\n- **Output impedance**: R_out = R_D (λ = 0); with r_O and source resistance R_S: R_out = R_D ‖ [r_O + (1 + g_m r_O)R_S].\n\n## Summary\n\nThe circuit is an NMOS common‑gate amplifier biased with V_G = V_DD: non‑inverting gain A_v ≈ g_m R_D, low input impedance ≈ 1/g_m, output impedance ≈ R_D, requires V_in < V_DD − V_TH to conduct, and stays in saturation only while the drop across R_D is ≤ V_TH.",
        "format": "markdown",
        "sha256": "78587966cc86bc3e6aedb741e75b4dbafc7eb620524734b4b5366c6536cd4902"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven NMOS common-gate stage and gives the non-inverting gain and low input resistance. The additional bias and impedance analysis is consistent with the stated assumptions.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 10227,
        "total_tokens": 11462,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8897,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 10227,
        "total_tokens": 11462,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8897,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Identifying the topology\n\n- M1 is an NMOS device (the arrow on the lower lead marks the source, pointing out of the device).\n- **Source** → V_in (input)\n- **Gate** → V_DD (a constant voltage ⇒ ac ground)\n- **Drain** → V_out, with load resistor R_D to V_DD\n\nInput applied at the source, output taken at the drain, gate held at a fixed potential: this is a **common‑gate (CG) stage** whose gate bias voltage V_b happens to be V_DD.\n\n## 2. DC operating point\n\nWith a dc input level V_IN:\n\n- V_GS = V_DD − V_IN, so M1 conducts only if V_IN < V_DD − V_TH.\n- I_D = ½ μ_nC_ox (W/L)(V_DD − V_IN − V_TH)²  (λ = 0)\n- V_OUT = V_DD − I_D R_D\n\nSaturation requires V_DS ≥ V_GS − V_TH, i.e. V_D ≥ V_G − V_TH:\n\n  V_DD − I_D R_D ≥ V_DD − V_TH  ⟹  **I_D R_D ≤ V_TH**\n\nSo the dc drop across R_D can never exceed one threshold voltage; the drain (output) is confined to V_DD − V_TH ≤ V_OUT ≤ V_DD. Note also that the bias current I_D flows *out* of the source into the input network, so whatever drives V_in must be able to sink I_D.\n\n## 3. Small‑signal analysis (λ = 0, no body effect)\n\nV_DD is ac ground, so v_g = 0 and v_gs = −v_in.\nThe small‑signal drain current (drain→source) is i_d = g_m v_gs = −g_m v_in. This same current flows through R_D, so\n\n  v_out = −i_d R_D = g_m R_D v_in\n\n  **A_v = v_out / v_in = +g_m R_D** (non‑inverting, as expected for a CG stage)\n\nRefinements:\n- Channel‑length modulation: A_v = (1 + g_m r_O) R_D /(R_D + r_O) ≈ g_m (R_D ‖ r_O)\n- Body effect (bulk at ground, so v_bs = −v_in): g_m → g_m + g_mb, A_v = (g_m + g_mb) R_D\n- Finite source resistance R_S driving the input: A_v = R_D /(R_S + 1/g_m)\n\n## 4. Impedances\n\n- **Input impedance** (looking into the source): R_in = 1/g_m  (or 1/(g_m + g_mb); with r_O: (R_D + r_O)/(1 + g_m r_O)) — low.\n- **Output impedance**: R_out = R_D (λ = 0); R_D ‖ r_O for an ideal voltage input; R_D ‖ [r_O(1 + g_m R_S) + R_S] with source resistance R_S.\n- Current gain ≈ 1: the stage acts as a current buffer with low input and high(er) output impedance.\n\n## 5. Key observations\n\n- Because the gate sits at V_DD, the saturation constraint I_D R_D ≤ V_TH caps the achievable gain:\n  A_v = g_m R_D = 2 I_D R_D /(V_GS − V_TH) ≤ 2V_TH / V_OV.\n  For example, with V_TH = 0.4 V and V_OV = 0.2 V the gain cannot exceed ≈ 4, and the output swing is limited to about V_TH.\n- The stage is non‑inverting, has R_in ≈ 1/g_m (useful for matching to low‑impedance sources such as 50 Ω lines), and R_out ≈ R_D.\n- If more gain/headroom is needed, the gate should be biased at V_b < V_DD (with V_IN lowered correspondingly) so that the drain can drop further before M1 enters the triode region.",
        "format": "markdown",
        "sha256": "f55f8e80ebe2c92b08eb3b22d6ca6c9dc71b694b2705da02d337d6391d04cf2e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven common-gate topology and gives the essential results: Rin ≈ 1/gm and a non-inverting gain ≈ gmRD, with an appropriate ro refinement. The additional operating-point and impedance discussion is consistent with the stated assumptions.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 25297,
        "total_tokens": 26532,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23973,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 25297,
        "total_tokens": 26532,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23973,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Circuit identification**\n\n- M1 is an NMOS device (arrow on the lower terminal = source).  \n- The input is applied to the **source**, the output is taken from the **drain**, and the **gate is tied to V_DD**, which is a small‑signal (ac) ground.  \n→ This is a **common‑gate (CG) amplifier** whose gate bias is simply V_DD, with a resistive drain load R_D.\n\n---\n\n**1. Large‑signal / bias analysis**\n\nWith V_G = V_DD:\n\n- V_GS = V_DD − V_in  \n- M1 is **off** if V_in ≥ V_DD − V_TH (then V_out = V_DD).  \n- For V_in < V_DD − V_TH, with λ = 0 and M1 in saturation:\n\n  I_D = ½ μ_nC_ox (W/L)(V_DD − V_in − V_TH)²  \n  V_out = V_DD − I_D R_D\n\n  As V_in decreases, V_GS grows, I_D grows and V_out falls – the characteristic V_out(V_in) has a **positive slope** (non‑inverting).\n\n- **Saturation condition:** V_DS ≥ V_GS − V_TH  \n  ⇒ V_out − V_in ≥ V_DD − V_in − V_TH  \n  ⇒ **V_out ≥ V_DD − V_TH**, i.e. **I_D R_D ≤ V_TH**\n\n  So the dc drop across R_D may not exceed one threshold voltage; if it does, M1 enters the triode region (and eventually behaves as a resistor R_on in series with R_D).  \n  The edge of saturation is reached at  \n  V_in = V_DD − V_TH − √(2V_TH /[μ_nC_ox(W/L)R_D]).\n\n- Note also that the signal source must **sink the entire bias current I_D** (there is no other dc path from the source terminal); in practice a current source or resistor would be placed at the source with capacitive coupling.\n\n---\n\n**2. Small‑signal analysis (gate at ac ground)**\n\nv_gs = 0 − v_in = −v_in, so the dependent current g_m v_gs = −g_m v_in flows drain→source, i.e. g_m v_in flows into the drain node. KCL at the drain:\n\n−v_out/R_D + g_m v_in = 0 ⇒ **A_v = v_out / v_in = + g_m R_D** (λ = 0)\n\nIncluding channel‑length modulation (r_O):\n\nA_v = (1 + g_m r_O) R_D / (R_D + r_O) ≈ g_m (R_D ∥ r_O)\n\nImpedances:\n\n- Input impedance (looking into the source): **R_in = 1/g_m** (with r_O: (R_D + r_O)/(1 + g_m r_O) ≈ 1/g_m + R_D/(g_m r_O)) – low.  \n- Output impedance: **R_out = R_D** (with r_O and an ideal input source: R_D ∥ r_O).  \n- If the signal source has resistance R_S: A_v = g_m R_D /(1 + g_m R_S).  \n- With body effect (bulk grounded, source not at ground): g_m → g_m + g_mb, so A_v = (g_m + g_mb)R_D and R_in = 1/(g_m + g_mb); V_TH also rises with V_SB = V_in.\n\n---\n\n**3. Key observations / limitations**\n\n- Same gain magnitude as a CS stage but **non‑inverting**, with **low input impedance** (useful for 50 Ω matching) and no Miller effect (good high‑frequency behaviour).\n- Because the gate is at V_DD, the drain can swing only between **V_DD − V_TH and V_DD**: output swing ≤ V_TH.\n- Gain is therefore bounded:  \n  A_v = g_m R_D = 2 I_D R_D /(V_GS − V_TH) ≤ **2V_TH / V_ov**, where V_ov = V_DD − V_in,dc − V_TH.  \n  (e.g. V_TH = 0.4 V, V_ov = 0.2 V ⇒ A_v ≤ 4; allowing swing room, only ≈ 2.)  \n- Tying the gate to V_DD saves a bias voltage but costs headroom; a gate bias V_b < V_DD (ordinary CG stage) would allow V_out ≥ V_b − V_TH and larger I_D R_D, hence larger gain.",
        "format": "markdown",
        "sha256": "acdc4b9c346973cb09a855321384d9511b7b3c5fdf1557e0b4598cafb7962734"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven, gate-grounded common-gate stage and gives the positive gain and low input resistance. The added bias, saturation, and output-resistance analysis is consistent with the stated assumptions.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 13414,
        "total_tokens": 14649,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11914,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1235,
        "output_tokens": 13414,
        "total_tokens": 14649,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11914,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## What the circuit is supposed to be\n\nThe topology has the gate of M₁ held at a constant voltage V_b, the input applied (through coupling capacitor C₁) to the **source**, and the output taken at the **drain** through R_D. That is the signature of a **common‑gate (CG) amplifier**. However, the way it is biased makes it fail completely.\n\n## DC operating point\n\nAt DC, C₁ is an open circuit, so the input has no effect on the bias. The source is wired directly to ground, so\n\n$$V_{GS}=V_b,\\qquad I_D=\\tfrac12\\mu_nC_{ox}\\frac{W}{L}(V_b-V_{TH})^2\\quad(\\lambda=0)$$\n\n$$V_{out,DC}=V_{DD}-R_D I_D ,$$\n\nwith saturation requiring $V_{DD}-R_DI_D \\ge V_b-V_{TH}$.\n\nNote that I_D is set by (V_b − V_TH)² alone – there is no degeneration, so the bias is very sensitive to V_TH, temperature and process. But that is the lesser problem.\n\n## Small‑signal analysis\n\nFor the signal, the gate is at ac ground (V_b is constant). The source is **hard‑wired to ground**, so its ac voltage is forced to zero no matter what V_in does:\n\n$$v_S = 0 \\;\\Rightarrow\\; v_{GS}=v_G-v_S=0 \\;\\Rightarrow\\; i_d=g_m v_{GS}=0 \\;\\Rightarrow\\; v_{out}=-i_dR_D=0$$\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=0}$$\n\nEquivalently: the input resistance of a CG stage looking into the source is 1/g_m, but here it is shunted by a 0 Ω wire. All of the signal current $i_{in}=j\\omega C_1 v_{in}$ flows through C₁ straight into ground; none of it enters M₁. V_in simply sees a capacitor to ground, and M₁ acts as a fixed current source $I_D$ loading $R_D$, producing a constant $V_{out}$.\n\nSo the student remembered the CG *topology* (gate grounded, input at source, output at drain) but not its *biasing*: the source must not be shorted to ground, otherwise the input signal is shorted to ground as well.\n\n## How to fix it\n\nThe source needs a path that carries the DC bias current but presents a finite (ideally large) impedance to the signal—a resistor R_S or a current source between source and ground:\n\n- **Bias:** $I_D=\\dfrac{V_b-V_{GS}}{R_S}$ (now stabilized by R_S), with $V_b - I_DR_S > V_{TH}$ and drain still in saturation.\n- **Gain:** the signal now reaches the source: $v_S=v_{in}$ (ideal source), $i_d=-g_m v_{in}$,\n\n$$A_v=+g_mR_D$$\n\n(non‑inverting). With a signal‑source resistance $R_{sig}$: $A_v=\\dfrac{R_D}{R_{sig}+1/g_m}$ (for $R_S\\gg 1/g_m$).\n- **Input impedance:** $R_{in}=\\dfrac{1}{g_m}\\parallel R_S$ (low, as expected for a CG stage); **output impedance** ≈ $R_D$.\n\n**Summary:** as drawn, the circuit is a properly biased transistor but a useless amplifier—because the source is tied to ground, the capacitively coupled input is shorted to ground, V_GS cannot vary, and the voltage gain is exactly zero. Inserting R_S (or a current source) in the source lead restores proper CG operation with A_v ≈ g_mR_D.",
        "format": "markdown",
        "sha256": "37f8dbbf30c643eb317a45c003872a430d9df11437667af470852371d87d7a84"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly notices that the source is hard-shorted to ground, so the input signal cannot modulate the transistor and the ideal voltage gain is zero, as required by the full-credit rule.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 7852,
        "total_tokens": 9758,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6585,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 7852,
        "total_tokens": 9758,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6585,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is supposed to be**\n\nThe gate of M₁ is held at a constant voltage V_b, the input is capacitively coupled (C₁) to the source, and the output is taken at the drain across R_D. This is the *intended* common‑gate (CG) topology: gate = AC ground, signal in at the source, signal out at the drain.\n\n**DC (bias) conditions**\n\n- Source is tied directly to ground → V_S = 0  \n- Gate at V_b → V_GS = V_b (fixed)  \n- I_D = ½ µₙC_ox (W/L)(V_b − V_TH)² (λ = 0)  \n- V_out(DC) = V_DD − I_D R_D, and M₁ is in saturation if V_DD − I_D R_D > V_b − V_TH.\n\nSo the bias point is well defined – nothing wrong so far.\n\n**Small‑signal behavior – the problem**\n\nC₁ delivers v_in to the source node, but that node is a hard short to ground. Therefore\n\n- v_s = 0 regardless of v_in (the input signal is simply shorted to ground through C₁; the source V_in only pushes a current i = C₁·dv_in/dt into ground and, at high frequencies, is effectively short‑circuited).\n- v_g = 0 (V_b is constant) → v_gs = v_g − v_s = 0\n- i_d = g_m·v_gs = 0 → v_out = −i_d R_D = 0\n\nHence\n\n  A_v = v_out / v_in = 0.\n\nThe transistor behaves as a constant current source (I_D set by V_b) feeding R_D; V_out contains only the DC value V_DD − I_D R_D and no signal. The circuit does not amplify at all, because both terminals that define V_GS (gate and source) are pinned to fixed potentials, so the input can never modulate the drain current.\n\n**How to fix it**\n\nThe short between source and ground must be replaced by a finite impedance so the source can move with the signal: insert a resistor R_S (or a current source) from source to ground. Then\n\n- Bias: V_b − V_GS = I_D R_S (sets I_D), V_out(DC) = V_DD − I_D R_D.\n- At signal frequencies where 1/(ωC₁) ≪ R_S ∥ (1/g_m), v_s ≈ v_in, and the stage works as a proper CG amplifier:\n A_v = g_m R_D (λ = 0), R_in = (1/g_m) ∥ R_S, R_out = R_D, non‑inverting gain.\n\nIn short: as drawn, the grounded source shorts out the input, V_GS is constant, and the voltage gain is zero; a source resistor (or current source) is required for the common‑gate stage to function.",
        "format": "markdown",
        "sha256": "8615857e6d3eaa28c4f3611a00ed0aa710c85a53a8616e87309e3dc9319f8269"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It recognizes that the source is hard-shorted to ground, so the input cannot modulate the transistor and the ideal voltage gain is zero, as required for full credit.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 5139,
        "total_tokens": 7045,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4235,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 5139,
        "total_tokens": 7045,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4235,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is supposed to be**\n\nGate at a fixed bias V_b (an ac ground), input applied to the source through a coupling capacitor C₁, output taken at the drain across R_D → this is meant to be a **common‑gate (CG) stage**, with the capacitor added so that the dc level of the signal source does not disturb the bias of M₁.\n\n**1. DC (bias) analysis – this part is fine**\n\nC₁ is open at dc, so\n\n- V_GS = V_b (source is at 0 V)\n- I_D = ½ μₙC_ox (W/L)(V_b − V_TH)²  (λ neglected)\n- V_out,DC = V_DD − I_D R_D\n\nM₁ is in saturation as long as V_DD − I_D R_D ≥ V_b − V_TH. There *is* a dc path for the drain current (V_DD → R_D → M₁ → ground), so g_m = 2I_D/(V_b − V_TH) ≠ 0. Unlike the version with only a capacitor at the source, this circuit does have a bias current.\n\n**2. Small‑signal analysis – the circuit does not work**\n\nReplace V_DD and V_b by ac grounds. The source terminal of M₁ is tied by a *wire* to ground, so its small‑signal voltage is\n\n  v_s = 0, regardless of v_in.\n\n- v_gs = v_g − v_s = 0 − 0 = 0\n- i_d = g_m v_gs = 0\n- v_out = −i_d R_D = 0\n\n  **A_v = v_out / v_in = 0**\n\nPhysically, the input signal is short‑circuited: V_in simply pushes a current i = C₁·dV_in/dt through C₁ straight into ground. The transistor's 1/g_m input resistance is shorted out, so none of the signal current enters M₁, and V_out just sits at V_DD − I_D R_D. The impedance seen by the source is only Z_in = 1/(jωC₁) in series with a short.\n\n**3. Why it fails and how to fix it**\n\nThe source node needs two things at once:\n- a **dc path** to ground to carry the bias current, and\n- a **high ac impedance** to ground so the signal is not shorted.\n\nA wire provides the first but destroys the second (this circuit); a capacitor alone provides the second but destroys the first (zero I_D). The remedy is to connect the source to ground through a **resistor R_S or, better, a current source I_S** (e.g., a current‑mirror transistor), with the gate biased from a divider R₁/R₂.\n\nWith R_S (λ neglected, C₁ large):\n- Bias: I_D = (V_b − V_GS)/R_S\n- R_in = (1/g_m) ∥ R_S ≈ 1/g_m  (low – a CG property)\n- A_v = v_out/v_in = +g_m R_D  (non‑inverting; reduced by R_in/(R_in + R_sig) if the signal source has resistance R_sig)\n- R_out = R_D\n\n**Conclusion:** the circuit as drawn is properly biased but has zero voltage gain, because grounding the source shorts the ac‑coupled input to ground. It must be modified by inserting R_S or a current source between the source of M₁ and ground.",
        "format": "markdown",
        "sha256": "98af7d344424c22df461b832ff982183a1bbaf99185dc731e50a89ac95aaac67"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that the source is hard-shorted to ground, so the input is shunted and the ideal small-signal voltage gain is zero. The additional bias and repair discussion does not undermine the essential conclusion.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 7450,
        "total_tokens": 9356,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6376,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1906,
        "output_tokens": 7450,
        "total_tokens": 9356,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6376,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- The source of M₁ is grounded, so C_SB has both terminals at ground and is shorted out – it plays no role.\n- That leaves C_GS (gate–ground), C_GD (gate–drain) and C_DB (drain–ground). Although there are three capacitors, they form a closed loop (ground → gate → drain → ground), so only two of their voltages are independent (V_GD = V_G – V_D). Hence the circuit has only two independent energy‑storage elements.\n\nDirect nodal analysis confirms this: the transfer function is\n\nV_out/V_in = (C_GD s − g_m)R_D / [ R_S R_D ξ s² + ((1+g_mR_D)C_GD R_S + R_S C_GS + R_D(C_GD + C_DB)) s + 1 ],\n\nwith ξ = C_GS C_GD + C_GS C_DB + C_GD C_DB — a second‑order denominator, i.e., two poles (one associated with the input/gate node and one with the output/drain node), plus one zero at s = g_m/C_GD.",
        "format": "markdown",
        "sha256": "3daf7bf03eed0ff7552ea21b0814616d3899e77e89c446a2d15f7b34f5d4d39a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that C_SB is shorted out and that the remaining capacitors have only two independent voltages. The stated transfer function also has a second-order denominator, confirming two poles.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 1808,
        "total_tokens": 3936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1441,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 1808,
        "total_tokens": 3936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1441,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- The source of M₁ is grounded, so C_SB has both terminals at ground and is shorted out – it has no effect.\n- That leaves three capacitors: C_GS (gate–ground), C_GD (gate–drain), and C_DB (drain–ground). However, these three form a closed loop (gate → ground → drain → gate), so their voltages are not independent: only two independent state variables (e.g., V_G and V_out) exist.\n\nHence the denominator of the transfer function is second‑order. Indeed, writing KCL at the gate and drain nodes gives\n\n$$\n\\frac{V_{out}}{V_{in}}(s)=\\frac{(C_{GD}s-g_m)R_D}{R_SR_D\\xi\\,s^2+\\big[R_S(1+g_mR_D)C_{GD}+R_SC_{GS}+R_D(C_{GD}+C_{DB})\\big]s+1}\n$$\n\nwith ξ = C_GS C_GD + C_GS C_DB + C_GD C_DB, which has two poles (and one right‑half‑plane zero at s = g_m/C_GD).",
        "format": "markdown",
        "sha256": "be44eaa2dc7de57ff2772412e28cf7d72dca5ff26593ba974f95fee8f03d54f5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the count by noting that C_SB is shorted and the remaining capacitor voltages have only two independent states. The transfer function also has a second-order denominator.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 780,
        "total_tokens": 2908,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 780,
        "total_tokens": 2908,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- C_SB has both terminals at ground, so it is shorted out and plays no role.\n- The remaining capacitors C_GS (gate–ground), C_DB (drain–ground) and C_GD (gate–drain) form a closed loop, so only two of their voltages are independent. The circuit therefore has only two independent state variables (the gate‑node and drain‑node voltages), giving a second‑order system.\n\nWriting KCL at the gate and drain nodes (with R_S driving the gate and R_D at the drain) yields\n\nV_out/V_in = (C_GD·s − g_m)·R_D / [ R_S R_D ξ s² + ( R_S(1+g_mR_D)C_GD + R_S C_GS + R_D(C_GD+C_DB) ) s + 1 ],\n\nwith ξ = C_GS C_GD + C_GS C_DB + C_GD C_DB.\n\nThe denominator is quadratic in s → **2 poles** (plus one zero at s = +g_m/C_GD from the feedforward path through C_GD).",
        "format": "markdown",
        "sha256": "3ba65e43618e4ad82407976a4310bea073304719b9a400e821ff33866d1401b0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the capacitor count: C_SB is grounded at both ends, while C_GS, C_GD, and C_DB form a loop with only two independent capacitor voltages.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 1097,
        "total_tokens": 3225,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 737,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2128,
        "output_tokens": 1097,
        "total_tokens": 3225,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 737,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n- **M₁** is an NMOS device used as a **common‑gate (CG) stage**: the input V_in drives the *source*, the output is taken at the *drain* (load R_D to V_DD).\n- **R₁–R₂** form a resistive divider across the output. The tap voltage  \n  V_F = V_out·R₂/(R₁+R₂) is fed back to the *gate* of M₁.\n\nSmall‑signal (neglecting λ and, for now, body effect):\n\n I_d = g_m V_gs = g_m (V_F − V_in)\n\nSo the transistor itself performs the subtraction of the feedback voltage from the input: the source acts like a \"non‑inverting input\" and the gate like an \"inverting input.\"\n\n## 2. Feedback topology and polarity\n\n- **Sensing:** R₁+R₂ is connected *in parallel* with the output → the **output voltage** is sensed.\n- **Returning:** V_F is placed *in series* with V_in through the gate–source port (V_gs = V_F − V_in) → a **voltage** is returned.\n\n⇒ **Voltage‑voltage (series–shunt) feedback.**\n\nPolarity: V_out ↑ → V_F ↑ → V_gs ↑ → I_d ↑ → larger drop across R_D → V_out ↓. The loop opposes the change → **negative feedback**.\n\n## 3. Loop gain (break the loop at the gate)\n\nThe gate draws no low‑frequency current, so breaking the loop there introduces no loading error. Ground V_in, inject V_t at the gate (M₁ now acts as a CS stage):\n\n V_out = −g_m R_L V_t, R_L ≜ R_D ∥ (R₁+R₂)\n\n V_F = −g_m R_L · R₂/(R₁+R₂) · V_t\n\n **Loop gain:** T = βA = g_m R_L · R₂/(R₁+R₂) (positive → negative feedback)\n\nwith open‑loop gain A = g_m R_L (CG stage, feedback network loading included) and feedback factor β = R₂/(R₁+R₂). (If R₁+R₂ ≫ R_D, R_L ≈ R_D.)\n\n## 4. Closed‑loop gain\n\nDirect KCL at the output node: V_out/R_L = g_m(V_in − V_F) = g_m(V_in − βV_out), hence\n\n **V_out/V_in = g_m R_L / [1 + g_m R_L·R₂/(R₁+R₂)]** = A/(1+βA)\n\nFor large loop gain:\n\n V_out/V_in → 1/β = **1 + R₁/R₂**\n\n—exactly the non‑inverting op‑amp configuration, with M₁ playing the role of the op amp (source = +, gate = −).\n\n## 5. Terminal impedances\n\n**Input impedance** (looking into the source):\n\n- open loop: 1/g_m\n- closed loop (series mixing raises it):\n R_in = (1/g_m)(1 + βA) = 1/g_m + β R_L\n\n(check: I_x = g_m(V_x − V_F), V_F = β R_L I_x → V_x/I_x = (1 + g_mβR_L)/g_m)\n\n**Output impedance** (V_in = 0):\n\n- open loop: R_L = R_D ∥ (R₁+R₂)\n- closed loop (shunt sensing lowers it):\n R_out = R_L/(1 + βA) = 1 / [1/R_D + 1/(R₁+R₂) + g_m R₂/(R₁+R₂)]\n\n(check: I_x = V_x/R_L + g_m βV_x)\n\n## 6. Remarks\n\n- **Loading of the feedback network:** at the output it appears as R₁+R₂ in parallel with R_D (included in R_L); at the input its Thevenin resistance R₁∥R₂ sits in series with the gate and has no effect at low frequency (gate current = 0).\n- **Biasing:** the same divider sets the DC gate voltage, V_GS = V_out,DC·R₂/(R₁+R₂) − V_in,DC, which must exceed V_TH.\n- **Body effect** (bulk grounded): I_d = g_m(V_F − V_in) − g_mb V_in. The loop gain is unchanged (g_mβR_L), but the forward gain becomes (g_m+g_mb)R_L, so\n V_out/V_in = (g_m+g_mb)R_L / (1 + g_mβR_L) → (1 + g_mb/g_m)(1 + R₁/R₂).\n\n**Summary:** a CG stage with voltage–voltage negative feedback; loop gain g_m R_L R₂/(R₁+R₂); closed‑loop gain g_m R_L /(1+ g_m R_L R₂/(R₁+R₂)) ≈ 1 + R₁/R₂; input impedance increased and output impedance decreased by the factor (1 + loop gain).",
        "format": "markdown",
        "sha256": "0513248673a5962867003befbd844ea3dac3d7cc5962b67435c741e5ba96d71d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-divider feedback to the gate, and negative-feedback polarity. The closed-loop gain matches the golden solution; the additional impedance and body-effect discussion does not contradict the essential analysis.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 14783,
        "total_tokens": 16557,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13121,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 14783,
        "total_tokens": 16557,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13121,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n- **M1 + R_D** form a **common‑gate (CG) amplifier**: the signal enters at the source, leaves at the drain. A CG stage is non‑inverting (V_in ↑ ⇒ I_D ↓ ⇒ V_out ↑).\n- **R1–R2** form a **feedback network**. They are connected *across* the output node (they sense V_out as a voltage) and deliver\n\n  V_F = V_out · R2/(R1+R2)\n\n  to the gate. The gate draws no current, so this is an ideal voltage return.\n- The transistor itself performs the subtraction: what controls I_D is V_GS = V_F − V_in. The input and the fed‑back voltage are therefore combined *in series* (as voltages).\n\n⇒ This is **voltage–voltage (series–shunt) feedback**. The source behaves like the \"+\" input and the gate like the \"−\" input of an op amp, so the circuit is the transistor‑level version of the non‑inverting op‑amp amplifier.\n\n## 2. Polarity of the feedback\n\nAssume V_in rises:\nV_in ↑ → V_GS = V_F − V_in ↓ → I_D ↓ → V_out = V_DD − I_D R_D ↑ → V_F ↑ → V_GS ↑ (opposes the original drop in V_GS).\n\nThe returned signal opposes the effect of the input ⇒ **negative feedback**. (Equivalently, breaking the loop at the gate and injecting v_t gives v_F = −g_m R_D′·R2/(R1+R2)·v_t < 0.)\n\n## 3. Open‑loop amplifier, feedback factor, loop gain\n\n(λ = 0, body effect neglected.)\n\nLoading of the feedback network:\n- At the output: the return port (gate) is open, so the divider loads the drain with R1+R2 ⇒ R_D′ = R_D ∥ (R1+R2).\n- At the input: shorting the sense port leaves R1∥R2 from gate to ground – irrelevant because I_G = 0.\n\nOpen‑loop CG stage:\n\n- A₀ = g_m R_D′\n- R_in,open = 1/g_m\n- R_out,open = R_D′\n\nFeedback factor: K = R2/(R1+R2)\n\nLoop gain: K·A₀ = g_m R_D′ · R2/(R1+R2)\n\n## 4. Closed‑loop results\n\n| Quantity | Result |\n|---|---|\n| Gain | A_v = A₀/(1+KA₀) = g_m R_D′ / [1 + g_m R_D′ R2/(R1+R2)] |\n| Input impedance | R_in = (1/g_m)(1+KA₀) = 1/g_m + R_D′ R2/(R1+R2)  (raised – series mixing) |\n| Output impedance | R_out = R_D′/(1+KA₀) = R_D′ / [1 + g_m R_D′ R2/(R1+R2)]  (lowered – voltage sensing) |\n\nIf R1+R2 ≫ R_D, simply replace R_D′ by R_D.\n\n## 5. Direct check by KCL\n\nNode V_F: v_F = β v_out, β = R2/(R1+R2).\nNode V_out: v_out/R_D + (v_out−v_F)/R1 + g_m(v_F − v_in) = 0, and (v_out−v_F)/R1 = v_out/(R1+R2), so\n\nv_out(1/R_D′ + g_m β) = g_m v_in ⇒ v_out/v_in = g_m R_D′/(1+β g_m R_D′) ✓\n\nInput current: i_in = g_m(v_in − v_F) = g_m v_in(1 − βA_v) ⇒ R_in = (1+βg_m R_D′)/g_m ✓\nOutput (v_in = 0, test v_x): i_x = v_x/R_D′ + g_m β v_x ⇒ R_out = R_D′/(1+βg_m R_D′) ✓\n\nThe feedback formulas are exact here because the gate draws no current.\n\n## 6. Interpretation\n\n- For large loop gain: A_v → 1/K = **1 + R1/R2**, set by a resistor ratio and insensitive to g_m, R_D, temperature, process (gain desensitization); R_in becomes large (≈ R_D′R2/(R1+R2) ≫ 1/g_m), R_out becomes small (≈ (1/g_m)(1+R1/R2)); bandwidth extended and linearity improved by the factor 1+KA₀.\n- Being a single‑transistor loop, the loop gain g_m R_D′R2/(R1+R2) is modest, so the ideal 1+R1/R2 is only approached, not reached.\n- Remarks: with finite r_O, replace R_D′ by R_D′∥r_O (approximately); with body effect the forward transconductance becomes g_m+g_mb while the feedback path still uses g_m. At dc the same divider biases the gate and stabilizes the operating point (I_D ↑ ⇒ V_out ↓ ⇒ V_F ↓ ⇒ V_GS ↓).",
        "format": "markdown",
        "sha256": "30e80eb3c608268c3c4d64e03dd8488a80a4997e1ad632c9464ee0167da05189"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-divider feedback to the gate, and negative feedback; its closed-loop gain matches the golden result. The full-credit rule applies.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 18522,
        "total_tokens": 20296,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16790,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 18522,
        "total_tokens": 20296,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16790,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the circuit**\n\n- M₁ is a **common‑gate (CG) stage**: the input drives the source, the output is taken at the drain, and R_D is the load.\n- R₁–R₂ is a **feedback network**: it senses V_out as a *voltage* (connected in parallel/shunt with the output node), divides it, and returns\n\n V_F = K·V_out, K = R₂/(R₁+R₂)\n\n to the gate. The transistor itself does the subtraction, because its controlling voltage is\n\n V_GS = V_F − V_in.\n\n So the returned quantity is a voltage placed in *series* with the input → **voltage–voltage (series–shunt) feedback**. (The divider also sets the dc gate bias of M₁.)\n\n**Polarity check**\n\nV_in ↑ → V_GS ↓ → I_D ↓ → V_out = V_DD − I_D R_D ↑ → V_F ↑ → V_GS ↑ (opposes the original change) ⇒ **negative feedback**.\n\n**Open‑loop parameters** (λ = 0, body effect neglected, loading of the divider included)\n\nBreaking the loop (gate at ac ground) leaves a CG stage whose drain also sees R₁+R₂ to ground; the gate node draws no current so the divider does not load the input side:\n\n- A₀ = g_m R_D′ , R_D′ ≡ R_D ∥ (R₁+R₂)\n- R_in,open = 1/g_m\n- R_out,open = R_D′\n- K = R₂/(R₁+R₂)\n- Loop gain: T = K A₀ = g_m R_D′ · R₂/(R₁+R₂)\n\n**Closed‑loop results**\n\nGain:\n A_v = V_out/V_in = A₀/(1+T) = g_m R_D′ / [1 + g_m R_D′ R₂/(R₁+R₂)]\n (for T ≫ 1, A_v → 1/K = 1 + R₁/R₂, set only by the resistor ratio)\n\nInput impedance (series mixing raises it):\n R_in = (1/g_m)(1+T) = 1/g_m + R_D′·R₂/(R₁+R₂)\n\nOutput impedance (voltage sensing lowers it):\n R_out = R_D′/(1+T) = R_D ∥ (R₁+R₂) ∥ [(R₁+R₂)/(g_m R₂)]\n\nIf R₁+R₂ ≫ R_D, simply replace R_D′ by R_D.\n\n**Direct check by KCL** (confirms the feedback results exactly)\n\nAt the output node: V_out/R_D + V_out/(R₁+R₂) + g_m(V_F − V_in) = 0 with V_F = K V_out, giving\n\n V_out/V_in = g_m / [1/R_D + 1/(R₁+R₂) + g_m R₂/(R₁+R₂)],\n\nwhich is the same as A₀/(1+T) above. The input current is i_in = g_m(V_in − V_F) = g_m V_in/(1+T), confirming R_in, and with V_in = 0 a test voltage V_x at the output draws V_x[1/R_D + 1/(R₁+R₂) + g_m K], confirming R_out.\n\n**Summary**: a CG amplifier wrapped in negative voltage–voltage feedback. The loop gain g_m R_D′ R₂/(R₁+R₂) desensitizes the gain toward 1 + R₁/R₂, multiplies the (low) CG input impedance 1/g_m by (1+T), and divides the output impedance R_D′ by (1+T); the R₁–R₂ network simultaneously stabilizes the dc bias of M₁.",
        "format": "markdown",
        "sha256": "a0e691f0134774aa39ecdc607f9ac74aa6c01e4b6066655ce4ee7fad15cbe2ec"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven input, output-divider feedback to the gate, and negative feedback. Its closed-loop gain matches the expected expression; the additional impedance analysis is consistent with the stated assumptions.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 11252,
        "total_tokens": 13026,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10007,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1774,
        "output_tokens": 11252,
        "total_tokens": 13026,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10007,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nBoth devices are NMOS (arrows point out of the source terminals).\n\n- **M1**: gate = V_in, drain = V_DD, source = V_out → **common‑drain stage (source follower)**.\n- **M2**: gate = constant bias V_b, source = ground, drain = V_out → acts as a **current source** that sets the bias current of M1.\n\nSo the figure is an **NMOS source follower with an NMOS current‑source load** – a voltage buffer / level shifter.\n\n## 2. Large‑signal (DC) behaviour\n\nBias current (M2 in saturation, λ neglected):\n\nI_D = ½ μ_n C_ox (W/L)₂ (V_b − V_TH2)²\n\nBecause this current is (nearly) independent of V_out, M1 carries an almost constant current, so its V_GS is almost constant:\n\nV_out = V_in − V_GS1 = V_in − V_TH1 − √( 2I_D / [μ_n C_ox (W/L)₁] )\n\n- For V_in < V_TH1: M1 is off, I_D = 0, V_out ≈ 0.\n- For V_in > V_TH1: V_out follows V_in with a roughly constant downward level shift of V_GS1. The slope is slightly less than one because V_TH1 rises with V_out (body effect, V_SB1 = V_out):\n  V_TH1 = V_TH0 + γ(√(2Φ_F + V_out) − √(2Φ_F)).\n\nOperating limits:\n\n- M2 stays in saturation if V_out ≥ V_b − V_TH2 = V_OD2 → V_in,min ≈ V_GS1 + V_OD2.\n- M1 stays in saturation if V_DS1 ≥ V_GS1 − V_TH1 → V_in ≤ V_DD + V_TH1 (always true for V_in ≤ V_DD).\n- Output range ≈ V_OD2 … V_DD − V_GS1.\n\n## 3. Small‑signal analysis\n\nM1: g_m1, g_mb1, r_o1. M2: its gate is at AC ground, so it is just r_o2. The drain of M1 is at AC ground.\n\nKCL at the output node:\n\ng_m1(v_in − v_out) − g_mb1 v_out − v_out/r_o1 = v_out/r_o2\n\n**Voltage gain**\n\nA_v = v_out / v_in = g_m1 / ( g_m1 + g_mb1 + 1/r_o1 + 1/r_o2 )\n  = g_m1 (r_o1‖r_o2) / [ 1 + (g_m1 + g_mb1)(r_o1‖r_o2) ]\n\nIntuitive view: a resistive divider between 1/g_m1 (looking into the source of M1) and R_S,eff = r_o1 ‖ r_o2 ‖ 1/g_mb1.\n\nWith r_o → ∞:\n\nA_v ≈ g_m1 / (g_m1 + g_mb1) = 1 / (1 + η),  η = g_mb1/g_m1 ≈ 0.2–0.3 → A_v ≈ 0.8\n\n**Output resistance**\n\nR_out = 1/g_m1 ‖ 1/g_mb1 ‖ r_o1 ‖ r_o2 ≈ 1/(g_m1 + g_mb1)  (low)\n\n**Input resistance**: ≈ ∞ at low frequency (gate).\n\nIf a load R_L is connected to V_out, it simply appears in parallel: add 1/R_L to the denominator of A_v.\n\n## 4. Key observations\n\n- **Function**: unity‑gain‑like buffer with high input impedance, low output impedance, and a DC level shift of −V_GS1.\n- **Why a current source instead of a resistor**: with a resistor R_S the gain would be g_m1 R_S /(1 + (g_m1+g_mb1)R_S) and the current through M1 would change with V_in, making V_GS1 and the gain input‑dependent (nonlinear). With M2 as a current source, r_o2 ≫ R_S gives a gain closer to 1 and I_D is ~constant, so V_GS1 is ~constant → much better linearity.\n- **Remaining limitations**:\n  - Body effect of M1 keeps the gain below 1 and introduces nonlinearity (can be removed with a PMOS follower whose source is tied to its own n‑well, at the cost of lower g_m).\n  - Voltage headroom: output is at least V_GS1 below the input and cannot go below V_OD2.\n  - Driving a small R_L requires large g_m1 (large W/L and/or current).\n  - Adds noise and consumes static power (I_D).\n- **Speed**: output pole ≈ (g_m1 + g_mb1)/C_L, so the stage is fast; C_GS1 provides a direct feed‑forward path (zero) from input to output.",
        "format": "markdown",
        "sha256": "2eead3b3716038b0cc30f92c8cd6c8dab191c2a7b07ad5f403b91aa5ce8772d1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its NMOS current-source load, and gives the positive, sub-unity gain with an appropriate small-signal expression. The central answer satisfies the golden solution's full-credit rule.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 6123,
        "total_tokens": 7420,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4481,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 6123,
        "total_tokens": 7420,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4481,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Circuit identification\n\nBoth devices are NMOS transistors (arrow on the source pointing out). \n\n- **M1**: drain at V_DD, gate driven by V_in, source is the output node → it is connected as a **common‑drain stage (source follower)**.\n- **M2**: gate at a fixed bias V_b, source at ground, drain at the output node → it is in saturation with a constant V_GS, so it acts as a **current source (active load)** for M1.\n\nSo this is a **source follower with an NMOS current‑source load** – a voltage buffer / level shifter.\n\n---\n\n## Large‑signal (DC) behavior\n\n**Bias current** (set entirely by M2, if M2 is saturated):\n\n  I₁ = ½ μₙC_ox (W/L)₂ (V_b − V_TH2)²  (≈ constant, ignoring λ)\n\n**Transfer characteristic.** The same I₁ flows through M1, so V_GS1 is fixed:\n\n  V_GS1 = V_TH1 + √(2I₁ / (μₙC_ox(W/L)₁)) = V_TH1 + V_OD1\n\n  **V_out = V_in − V_GS1**\n\nThe output \"follows\" the input, shifted down by V_GS1. Because the current is constant (unlike a resistive‑load follower), V_GS1 is nearly constant, which gives good linearity. The remaining nonlinearity comes from the **body effect**: the bulk of M1 is at ground while its source is at V_out, so\n\n  V_TH1 = V_TH0 + γ(√(2Φ_F + V_out) − √(2Φ_F))\n\nincreases slowly with V_out, making the slope of V_out vs V_in slightly less than 1.\n\n**Operating regions / limits**\n\n- M1 is always saturated (or off): V_GD1 = V_in − V_DD ≤ 0 < V_TH.\n- V_in < V_TH0: M1 off, M2 pulls V_out to 0.\n- M2 stays in saturation only if V_out ≥ V_b − V_TH2 = V_OD2, i.e. V_in ≥ V_GS1 + V_OD2. Below this M2 enters triode and the stage stops following.\n- Maximum output: V_out,max = V_DD − V_GS1 (for V_in = V_DD).\n\nOutput swing ≈ from V_OD2 up to V_DD − V_GS1 — the V_GS1 level shift costs headroom.\n\n---\n\n## Small‑signal analysis\n\nSmall‑signal model: M1 → g_m1, g_mb1, r_o1; M2 (gate at AC ground) → just r_o2.\n\nKCL at the output node:\n\n  g_m1(v_in − v_out) − g_mb1·v_out − v_out/r_o1 − v_out/r_o2 = 0\n\n**Voltage gain:**\n\n  A_v = v_out/v_in = g_m1 / (g_m1 + g_mb1 + 1/r_o1 + 1/r_o2)\n    = g_m1·(r_o1‖r_o2) / [1 + (g_m1 + g_mb1)(r_o1‖r_o2)]\n\nWith λ = 0 (r_o → ∞): **A_v = g_m1/(g_m1 + g_mb1) = 1/(1 + η)**, typically ≈ 0.8–0.9. It never reaches unity because of the body effect (the gain is exactly 1 only if the bulk of M1 is tied to its source, e.g. in a triple‑well or using a PMOS version).\n\n**Input resistance:** R_in → ∞ (gate, at low frequency).\n\n**Output resistance** (looking into the source of M1):\n\n  R_out = (1/g_m1) ‖ (1/g_mb1) ‖ r_o1 ‖ r_o2 ≈ 1/(g_m1 + g_mb1)  — low.\n\n---\n\n## Summary / properties\n\n| Property | Result |\n|---|---|\n| Function | Voltage buffer / DC level shifter |\n| Gain | ≈ g_m1/(g_m1+g_mb1) < 1 (non‑inverting) |\n| R_in | very high |\n| R_out | ≈ 1/(g_m1+g_mb1), low |\n| Current | constant I₁ set by V_b and (W/L)₂ |\n\n**Advantages:** high input impedance, low output impedance, better linearity and gain closer to 1 than with a resistor load (r_o2 ≫ R_S, constant I₁), can drive low‑impedance/capacitive loads, provides a level shift.\n\n**Drawbacks:** gain < 1 and nonlinear due to body effect; V_GS1 level shift consumes voltage headroom (limited swing: V_OD2 … V_DD − V_GS1); asymmetric drive capability (M1 can source large current, but the sink current is limited to the fixed I₁ of M2, causing slewing with capacitive loads); nonlinearity from r_o1, r_o2 variation with V_DS.",
        "format": "markdown",
        "sha256": "0fcb6d0e4c8262819cefb94cca5978c18f5ca80569091f63a77cdd4bedd8883a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its NMOS current-source load, with a positive gain below unity and an appropriate small-signal expression. Minor ancillary imprecisions do not affect the essential answer.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 5251,
        "total_tokens": 6548,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3592,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 5251,
        "total_tokens": 6548,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3592,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nBoth devices are NMOS transistors (source arrows point outward).\n\n| Device | Gate | Drain | Source | Role |\n|---|---|---|---|---|\n| M1 | V_in | V_DD | V_out | Input (amplifying) device |\n| M2 | V_b (constant bias) | V_out | GND | Current‑source load |\n\nSince the drain of M1 is tied to V_DD (ac ground), the input is applied to the gate and the output is taken from the source, this is a **common‑drain stage, i.e. a source follower, with an active (current‑source) load**. M2, biased by a constant V_b, forces a nearly constant current\n\n$$I_{D2}\\approx\\tfrac12\\mu_nC_{ox}\\left(\\tfrac{W}{L}\\right)_2 (V_b-V_{TH2})^2$$\n\nthrough M1 and presents a high incremental resistance r_o2 at the output.\n\n## 2. Large‑signal (DC) behaviour\n\n- **V_in < V_TH1**: M1 is off, no current flows, V_out = 0 (M2 sits in triode with V_DS = 0).\n- **V_in slightly > V_TH1**: M1 turns on, current rises, M2 is still in triode (acts like a resistor ≈ 1/[μ_nC_ox(W/L)₂(V_b − V_TH2)]) and V_out starts to rise.\n- **Both in saturation** (V_out ≥ V_b − V_TH2): I_D1 = I_D2 = constant, so\n\n$$V_{GS1}=V_{TH1}+\\sqrt{\\frac{2I_{D2}}{\\mu_nC_{ox}(W/L)_1}}\\approx\\text{const}\\quad\\Rightarrow\\quad V_{out}\\approx V_{in}-V_{GS1}$$\n\n  The output *follows* the input with a level shift of −V_GS1. This is the useful operating region.\n- M1 stays in saturation as long as V_in ≤ V_DD + V_TH1 (drain is at V_DD), so for V_in ≤ V_DD it never enters triode.\n\n**Body effect:** the substrate of M1 is at ground while its source sits at V_out, so V_SB1 = V_out and\n\n$$V_{TH1}=V_{TH0}+\\gamma\\left(\\sqrt{2\\Phi_F+V_{out}}-\\sqrt{2\\Phi_F}\\right)$$\n\nThus V_GS1 is not perfectly constant; it grows slowly with V_out, making the slope of V_out vs V_in somewhat less than 1 and slightly nonlinear.\n\n**Why M2 instead of a resistor:** with a resistor R_S, I_D1 (and hence V_GS1 and g_m1) would change with V_out, causing strong nonlinearity. The current source fixes I_D1, so the only remaining nonlinearity is the body effect (and the finite r_o's).\n\n## 3. Small‑signal analysis\n\nM1: controlled sources g_m1·v_gs1 and g_mb1·v_bs1 (drain→source) plus r_o1, all between ac ground (V_DD) and v_out. M2 with its gate at ac ground is just r_o2 from v_out to ground.\n\nv_gs1 = v_in − v_out, v_bs1 = −v_out. KCL at the output node:\n\n$$g_{m1}(v_{in}-v_{out})-g_{mb1}v_{out}=\\frac{v_{out}}{r_{o1}}+\\frac{v_{out}}{r_{o2}}$$\n\n**Voltage gain**\n\n$$A_v=\\frac{v_{out}}{v_{in}}=\\frac{g_{m1}}{g_{m1}+g_{mb1}+\\dfrac{1}{r_{o1}}+\\dfrac{1}{r_{o2}}}\n=\\frac{g_{m1}\\,(r_{o1}\\parallel r_{o2})}{1+(g_{m1}+g_{mb1})(r_{o1}\\parallel r_{o2})}$$\n\nIf r_o1, r_o2 → ∞:\n\n$$A_v\\to\\frac{g_{m1}}{g_{m1}+g_{mb1}}=\\frac{1}{1+\\eta},\\qquad \\eta=\\frac{g_{mb1}}{g_{m1}}=\\frac{\\gamma}{2\\sqrt{2\\Phi_F+V_{SB}}}$$\n\nTypically η ≈ 0.1–0.3, giving A_v ≈ 0.75–0.9 — always less than unity, and equal to 1 only if the body effect could be eliminated (e.g., source tied to body, which is not possible here for NMOS in a p‑substrate process).\n\n**Output resistance** (set v_in = 0, apply v_x at the output):\n\n$$R_{out}=\\frac{1}{g_{m1}}\\;\\Big\\|\\;\\frac{1}{g_{mb1}}\\;\\Big\\|\\;r_{o1}\\;\\Big\\|\\;r_{o2}\\;\\approx\\;\\frac{1}{g_{m1}+g_{mb1}}$$\n\n(Note A_v = g_m1·R_out.) This is low — typically a few hundred ohms to a few kΩ.\n\n**Input resistance:** essentially infinite at low frequency (MOS gate).\n\nWith an external load R_L at the output, simply replace r_o1‖r_o2 by r_o1‖r_o2‖R_L in the gain expression.\n\n*Numerical example:* g_m1 = 1 mS, g_mb1 = 0.2 mS, r_o1 = r_o2 = 50 kΩ → A_v = 1/(1+0.2+0.02+0.02) ≈ 0.81, R_out ≈ 806 Ω.\n\n## 4. Voltage headroom and swing\n\n- Lowest output: M2 must stay saturated → V_out,min = V_b − V_TH2 = V_OD2.\n- Highest output: with V_in = V_DD, V_out,max = V_DD − V_GS1.\n- Useful input range: roughly V_OD2 + V_GS1 ≤ V_in ≤ V_DD.\n\nSo the stage \"eats\" one V_GS plus one overdrive voltage of headroom, and the output DC level is shifted down by V_GS1 relative to the input.\n\n## 5. Frequency behaviour (brief)\n\nBecause the gain is near unity, C_GS1 is largely bootstrapped; the input capacitance is ≈ C_GD1 + (1 − A_v)C_GS1, which is small — the follower is a good wideband buffer. The output pole is at roughly g_m1/C_L. When driven from a large source resistance R_S, the output impedance becomes inductive at high frequency (C_GS1 with R_S), which can cause ringing with capacitive loads.\n\n## 6. Summary\n\n**Function:** voltage buffer / level shifter — high input impedance, low output impedance (≈1/g_m), gain slightly below 1, output = input shifted down by V_GS1. Used e.g. to drive low‑impedance or capacitive loads, or to shift the DC level between stages.\n\n**Strengths:** near‑constant V_GS1 thanks to the current‑source load (better linearity and gain than a resistive load), small input capacitance, simple.\n\n**Limitations:**\n- Gain < 1 and mildly nonlinear because of the body effect of M1 (V_SB1 = V_out).\n- Consumes headroom (V_GS1 + V_OD2); output cannot reach V_DD or ground.\n- R_out ≈ 1/(g_m + g_mb) is not extremely low; gain degrades with heavy resistive loads.\n- Adds noise and poses potential stability issues with capacitive loads and large source resistance.\n- A PMOS follower (with source tied to its n‑well) would avoid the body effect at the cost of lower g_m.",
        "format": "markdown",
        "sha256": "f9b2c921d82387131affa69e90cb95b1a143ae4dcf05e71947517e968ac09dcd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its current-source load, and gives the correct positive, sub-unity gain expression. Minor issues in ancillary output-resistance wording do not affect the essential answer.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 7874,
        "total_tokens": 9171,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5228,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1297,
        "output_tokens": 7874,
        "total_tokens": 9171,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5228,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Recognizing the circuit\n\n| Device | Type | Source | Gate | Drain |\n|---|---|---|---|---|\n| M1 | NMOS | ground | Vin | Vout |\n| M2 | PMOS | VDD | Vin | Vout |\n\nBoth gates are driven by the same input and both drains form the output, so the two transistors are *complementary common‑source devices in parallel*. This is the **CMOS inverter** (or, viewed as an analog block, a push‑pull/complementary common‑source amplifier). Because the sources sit at the supply rails, there is no body effect.\n\n## 2. Large‑signal operation (voltage transfer characteristic)\n\nLet VTHN be the NMOS threshold and |VTHP| the PMOS threshold, βn = μnCox(W/L)1, βp = μpCox(W/L)2.\n\nM1 is saturated when Vout ≥ Vin − VTHN; M2 is saturated when Vout ≤ Vin + |VTHP|.\n\n| Input range | M1 | M2 | Output |\n|---|---|---|---|\n| Vin < VTHN | off | triode (no current) | Vout = VDD exactly |\n| VTHN < Vin < VM | saturation | triode | slightly below VDD |\n| Vin ≈ VM | saturation | saturation | steep transition |\n| VM < Vin < VDD − \\|VTHP\\| | triode | saturation | slightly above 0 |\n| Vin > VDD − \\|VTHP\\| | triode (no current) | off | Vout = 0 exactly |\n\nKey consequences:\n- **Rail‑to‑rail swing:** VOH = VDD, VOL = 0 (unlike a resistor‑loaded or NMOS‑loaded inverter).\n- **Zero static power:** in either logic state one transistor is cut off, so only leakage flows.\n- **Current flows only during the transition** (VTHN < Vin < VDD − |VTHP|), when both devices conduct (\"crowbar\" current). Its peak occurs at Vin = VM: I_peak = ½βn(VM − VTHN)².\n\n**Switching (trip) point VM**, defined by Vin = Vout with both devices saturated:\n\n½βn(VM − VTHN)² = ½βp(VDD − VM − |VTHP|)²\n\n⇒ VM = [VTHN + √(βp/βn)(VDD − |VTHP|)] / [1 + √(βp/βn)]\n\nFor VM = VDD/2 with VTHN = |VTHP| we need βn = βp, i.e. (W/L)2 ≈ (μn/μp)(W/L)1 ≈ 2–3 times the NMOS width. Increasing the PMOS size moves VM up; increasing the NMOS size moves it down.\n\nWith λ = 0 the VTC is vertical in the both‑saturated region; with channel‑length modulation it has the finite slope found below.\n\n## 3. Small‑signal analysis (both devices saturated)\n\nReplace each transistor by gm·vgs and rO. For M1: vgs1 = vin, current gm1·vin flows from Vout to ground. For M2: vsg2 = −vin, so a current gm2·vin also leaves the output node toward VDD. KCL at the output:\n\n(gm1 + gm2)·vin + vout/rO1 + vout/rO2 = 0\n\n**Av = vout/vin = −(gm1 + gm2)(rO1 ∥ rO2)**\n\n- Effective transconductance Gm = gm1 + gm2: the PMOS is not a passive load but an active amplifying device, so the stage gives roughly twice the gm of a CS stage with a current‑source load for the same bias current.\n- Output resistance Rout = rO1 ∥ rO2, so the gain is on the order of the intrinsic gain gm·rO (tens to a few hundred).\n- This high gain is what makes the logic transition sharp and gives good noise margins (VIL and VIH are the points where dVout/dVin = −1; NMH = VDD − VIH, NML = VIL).\n- Used as an amplifier (e.g., in Pierce crystal oscillators) it must be biased near VM, typically with a large feedback resistor from Vout to Vin.\n\n## 4. Dynamic behavior\n\n- **Input capacitance:** Cin ≈ CGS1 + CGS2 plus Miller‑multiplied CGD1, CGD2 during the transition.\n- **Output drive:** in each logic state the \"on\" transistor is in triode with Ron ≈ 1/[μCox(W/L)(VDD − VTH)], giving a low output impedance that charges/discharges CL.\n- **Delays:** tPHL ≈ 0.69·Ron,n·CL (M1 discharges), tPLH ≈ 0.69·Ron,p·CL (M2 charges). Equal delays again require the wider PMOS.\n- **Power:** P ≈ f·CL·VDD² (dynamic) + short‑circuit term during transitions + leakage; no DC term.\n\n## 5. Summary\n\nThe circuit is a CMOS inverter: a complementary pair in which exactly one transistor conducts at each logic level, yielding full‑swing outputs, zero static current, a sharp transition at VM set by the βp/βn ratio, and – when biased in the middle of its characteristic – an inverting amplifier with gain −(gm1 + gm2)(rO1 ∥ rO2).",
        "format": "markdown",
        "sha256": "e2fd8a2a4968d88b84f0700e77c9cfb924edf6d554f19b47520f710ee1b46c20"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, with an NMOS pull-down and PMOS pull-up, and describes its inverting operation. The optional analysis is largely consistent; minor terminology or modeling imprecision does not contradict inverter operation.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 6886,
        "total_tokens": 7212,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5069,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 6886,
        "total_tokens": 7212,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5069,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit identification\n\nThe figure shows a **CMOS inverter**: a complementary pair in which\n\n| Device | Type | Source | Gate | Drain |\n|---|---|---|---|---|\n| M₂ | PMOS | V_DD | V_in | V_out |\n| M₁ | NMOS | GND | V_in | V_out |\n\nBoth gates are driven by the same input and both drains share the output node. M₂ acts as the pull‑up device, M₁ as the pull‑down device. (Bulks are assumed tied to their own sources → no body effect.)\n\n---\n\n## 1. Large‑signal (logic) operation\n\nLet V_THN > 0 and V_THP < 0 be the threshold voltages.\n\n- **V_in = 0:** V_GS1 = 0 < V_THN → M₁ off. V_SG2 = V_DD > |V_THP| → M₂ on (triode) and pulls the output to **V_out = V_DD**.\n- **V_in = V_DD:** V_GS1 = V_DD → M₁ on (triode); V_SG2 = 0 → M₂ off, so **V_out = 0**.\n\nHence the logic function is V_out = NOT(V_in), with rail‑to‑rail output levels (V_OH = V_DD, V_OL = 0). In either steady state one transistor is cut off, so **no static current flows** between V_DD and ground (apart from leakage) – the defining advantage of CMOS logic.\n\n### Voltage‑transfer characteristic (VTC)\n\nSweeping V_in from 0 to V_DD takes the pair through five regions:\n\n| Region | Input range | M₁ | M₂ | Output |\n|---|---|---|---|---|\n| A | 0 ≤ V_in < V_THN | off | triode | V_DD |\n| B | V_THN ≤ V_in < V_M | saturation | triode | starts to fall |\n| C | V_in ≈ V_M | saturation | saturation | steep transition |\n| D | V_M < V_in ≤ V_DD − \\|V_THP\\| | triode | saturation | near 0 |\n| E | V_in > V_DD − \\|V_THP\\| | triode | off | 0 |\n\n(M₁ is saturated when V_out ≥ V_in − V_THN; M₂ is saturated when V_out ≤ V_in + |V_THP|.)\n\n### Switching threshold V_M (V_in = V_out)\n\nIn region C both devices are saturated. Equating drain currents (λ = 0), with β = μC_ox(W/L):\n\n$$\\tfrac12\\beta_n (V_M - V_{THN})^2 = \\tfrac12\\beta_p (V_{DD} - V_M - |V_{THP}|)^2$$\n\n$$\\boxed{V_M=\\frac{V_{THN}+\\sqrt{\\beta_p/\\beta_n}\\,\\bigl(V_{DD}-|V_{THP}|\\bigr)}{1+\\sqrt{\\beta_p/\\beta_n}}}$$\n\nFor a symmetric characteristic (V_M = V_DD/2) one needs β_n = β_p, i.e. (W/L)_p ≈ (μ_n/μ_p)(W/L)_n ≈ 2–3 × (W/L)_n. Increasing the PMOS strength moves V_M up; increasing the NMOS strength moves it down.\n\n### Noise margins\n\nSetting dV_out/dV_in = −1 gives V_IL and V_IH. For the symmetric case (β_n = β_p, V_THN = |V_THP| = V_T):\n\n$$V_{IL}=\\frac{3V_{DD}+2V_T}{8},\\qquad V_{IH}=\\frac{5V_{DD}-2V_T}{8}$$\n\n$$NM_L = V_{IL}-V_{OL}=\\frac{3V_{DD}+2V_T}{8},\\qquad NM_H = V_{OH}-V_{IH}=\\frac{3V_{DD}+2V_T}{8}$$\n\nBoth margins are a large fraction of V_DD (≈ 0.4–0.45 V_DD), which is why the CMOS inverter is so robust.\n\n---\n\n## 2. Power dissipation\n\n- **Static:** essentially zero (leakage only), because M₁ and M₂ are never both on at the logic levels.\n- **Short‑circuit (crowbar) current:** while V_THN < V_in < V_DD − |V_THP| during a transition, both devices conduct; the peak occurs at V_in = V_M, I_peak = ½β_n(V_M − V_THN)².\n- **Dynamic:** P ≈ α·C_L·V_DD²·f + P_short‑circuit + P_leak, where α is the activity factor and C_L the load capacitance.\n\n---\n\n## 3. Transient behaviour\n\nThe output falls by discharging C_L through M₁ and rises by charging C_L through M₂:\n\n$$t_{pHL}\\approx 0.69\\,R_{eq,n}C_L,\\qquad t_{pLH}\\approx 0.69\\,R_{eq,p}C_L$$\n\nBecause μ_p < μ_n, equal rise and fall delays require W_p ≈ (2–3)·W_n, the same condition that centres V_M. The input capacitance seen by the previous stage is C_gs1 + C_gs2 plus the Miller‑multiplied C_gd1 + C_gd2.\n\n---\n\n## 4. The same circuit as an analog amplifier\n\nIf the input is biased at V_in ≈ V_M (e.g. with a large feedback resistor from V_out to V_in plus an AC‑coupling capacitor), both devices sit in saturation and the inverter becomes a **push‑pull common‑source amplifier**.\n\nSmall‑signal KCL at the output node (M₁ sinks g_m1·v_in, M₂ injects −g_m2·v_in):\n\n$$-g_{m2}v_{in}=g_{m1}v_{in}+\\frac{v_{out}}{r_{o1}\\parallel r_{o2}}\\;\\;\\Rightarrow\\;\\;\n\\boxed{A_v=\\frac{v_{out}}{v_{in}}=-(g_{m1}+g_{m2})\\,(r_{o1}\\parallel r_{o2})}$$\n\n- **Output resistance:** R_out = r_o1 ∥ r_o2.\n- **Bandwidth / GBW:** dominant pole ≈ 1/[(r_o1∥r_o2)C_L], so GBW ≈ (g_m1+g_m2)/C_L.\n- **Efficiency:** both transistors contribute transconductance while sharing the same bias current, so for a given current the gain (and g_m/I_D) is roughly **twice** that of a CS stage with a current‑source load. This slope −(g_m1+g_m2)(r_o1∥r_o2) is also the steepness of the VTC in region C.\n- **Drawbacks:** the operating point (V_M) depends strongly on V_TH, mobility, temperature and V_DD (PVT‑sensitive, hence feedback biasing is needed); the supply is a direct signal path through M₂, giving poor PSRR (supply gain ≈ g_m2(r_o1∥r_o2), only ~6 dB below the signal gain); input capacitance is large (two gates plus Miller effect of two C_gd’s); and as an amplifier the stage draws a static current I_D(V_M), unlike in logic use.\n\nOutput swing with both devices in saturation (high‑gain region): V_in − V_THN ≤ V_out ≤ V_in + |V_THP|, but the output can go rail‑to‑rail if some gain loss is tolerated.\n\n---\n\n## Summary\n\nThe circuit is a CMOS inverter: a PMOS pull‑up (M₂) and NMOS pull‑down (M₁) sharing gate and drain nodes. As a logic gate it offers rail‑to‑rail output, near‑zero static power, large and symmetric noise margins (≈3V_DD/8 + V_T/4 when sized for β_n = β_p), and a switching threshold V_M set by the β_p/β_n ratio. Biased at V_M it doubles as a compact, current‑efficient push‑pull amplifier with gain −(g_m1+g_m2)(r_o1∥r_o2), at the cost of poor supply rejection and a PVT‑sensitive bias point.",
        "format": "markdown",
        "sha256": "75b2b6a16a0553e2abd9ccd9fcb8968a1f29362d3bd718f964639dacdbdd545a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, with a PMOS pull-up and NMOS pull-down, and describes its inverting logic operation. The golden solution grants full credit for this identification; the extra analysis does not contradict the essential answer.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 10011,
        "total_tokens": 10337,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7207,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 10011,
        "total_tokens": 10337,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7207,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Identification\n\nThe figure is the **CMOS inverter**, the basic building block of CMOS digital logic:\n\n- **M₁** – NMOS device (arrow pointing out of the source), source grounded\n- **M₂** – PMOS device (arrow pointing into the source), source tied to V_DD\n- Both gates are driven by V_in; both drains are tied together to form V_out.\n\nBecause the two devices are complementary, the same input voltage that turns one transistor *on* turns the other *off*. M₂ acts as the \"pull‑up\" (connects V_out to V_DD) and M₁ as the \"pull‑down\" (connects V_out to ground).\n\n---\n\n# Large-Signal Operation (Voltage Transfer Characteristic)\n\nDefine V_THN = threshold of M₁, |V_THP| = threshold magnitude of M₂, k_n = μ_nC_ox(W/L)₁, k_p = μ_pC_ox(W/L)₂. In steady state the same current flows through both devices (no DC load), so I_D1 = I_D2 at every point of the VTC.\n\n| Region | Input range | M₁ | M₂ | Output |\n|---|---|---|---|---|\n| A | V_in < V_THN | off | deep triode (V_SD ≈ 0) | V_out = V_DD |\n| B | V_THN < V_in < V_M | saturation | triode | V_out starts to fall |\n| C | V_in ≈ V_M | saturation | saturation | steep transition (very high gain) |\n| D | V_M < V_in < V_DD − |V_THP| | triode | saturation | V_out approaches 0 |\n| E | V_in > V_DD − |V_THP| | deep triode | off | V_out = 0 |\n\n**Region A:** V_GS1 = V_in < V_THN, so M₁ carries no current. M₂ has V_SG = V_DD − V_in > |V_THP|, is on, but with zero current its V_SD = 0 → **V_out = V_DD**.\n\n**Region B:** M₁ saturated, M₂ in triode:\n(k_n/2)(V_in − V_THN)² = k_p[(V_DD − V_in − |V_THP|)(V_DD − V_out) − (V_DD − V_out)²/2]\n\n**Region C (both saturated):** With λ = 0 the VTC is vertical; including channel-length modulation the slope is\ndV_out/dV_in = −(g_m1 + g_m2)(r_o1 ‖ r_o2)\nBoth devices remain saturated only while V_in − V_THN ≤ V_out ≤ V_in + |V_THP|, a narrow range of V_in.\n\n**Region D:** M₁ in triode, M₂ saturated:\nk_n[(V_in − V_THN)V_out − V_out²/2] = (k_p/2)(V_DD − V_in − |V_THP|)²\n\n**Region E:** V_SG2 = V_DD − V_in < |V_THP| → M₂ off, M₁ pulls **V_out = 0**.\n\nNote the *regenerative* nature: as V_in rises, M₁ conducts more **and** M₂ conducts less — both effects push V_out down, giving a far sharper transition than an NMOS inverter with a fixed (resistive or current-source) load.\n\n---\n\n# Switching Threshold (Trip Point)\n\nSetting V_in = V_out = V_M with both devices in saturation:\n\n(k_n/2)(V_M − V_THN)² = (k_p/2)(V_DD − V_M − |V_THP|)²\n\n$$V_M=\\frac{V_{THN}+r\\,(V_{DD}-|V_{THP}|)}{1+r},\\qquad r=\\sqrt{\\frac{\\mu_p (W/L)_2}{\\mu_n (W/L)_1}}$$\n\nFor a symmetric inverter (V_M = V_DD/2) with V_THN = |V_THP| we need r = 1, i.e. (W/L)₂/(W/L)₁ = μ_n/μ_p ≈ 2–3, so the PMOS is made wider to compensate for lower hole mobility.\n\n---\n\n# Noise Margins\n\nV_OH = V_DD and V_OL = 0 (full rail-to-rail swing, independent of device sizes — \"ratioless\" logic). V_IL and V_IH are found where the slope equals −1. For the symmetric case (k_n = k_p, V_THN = |V_THP| = V_TH):\n\n- V_IL = (3V_DD + 2V_TH)/8\n- V_IH = (5V_DD − 2V_TH)/8\n- NM_L = V_IL − V_OL = NM_H = V_OH − V_IH = (3V_DD + 2V_TH)/8\n\nNoise margins are large and equal, each well above V_DD/4.\n\n---\n\n# Power Dissipation\n\n- **Static power ≈ 0**: in either logic state one transistor is off, so no DC path exists from V_DD to ground (apart from leakage).\n- **Short-circuit (crowbar) current** flows only during a transition when V_THN < V_in < V_DD − |V_THP|, peaking at V_in = V_M: I_peak = (k_n/2)(V_M − V_THN)².\n- **Dynamic power** from charging/discharging a load C_L: P = C_L V_DD² f.\n\n---\n\n# Switching Speed\n\nWith a load capacitor C_L at the output:\n\n- **High-to-low**: M₁ discharges C_L; t_PHL ∝ C_L V_DD / [k_n (V_DD − V_THN)²]\n- **Low-to-high**: M₂ charges C_L; t_PLH ∝ C_L V_DD / [k_p (V_DD − |V_THP|)²]\n\nEqual rise and fall delays again require k_p = k_n, i.e. a wider PMOS.\n\n---\n\n# Small-Signal View (Inverter as an Amplifier)\n\nIf biased near V_M (e.g. with a feedback resistor from output to input), both devices are saturated and the circuit is a **push-pull common-source amplifier**: M₂ is not merely a load but also a transconductor driven by V_in.\n\n- Voltage gain: A_v = −(g_m1 + g_m2)(r_o1 ‖ r_o2)\n- Output resistance: R_out = r_o1 ‖ r_o2\n- Input resistance: ∞ (gate inputs)\n\nFor a given bias current, the gain is roughly double that of a CS stage with a current-source load, because both transconductances add.\n\n---\n\n# Summary of Key Properties\n\n1. Logic inverter: V_out = V_DD for low V_in, V_out = 0 for high V_in.\n2. Rail-to-rail output swing, independent of transistor ratios.\n3. Essentially zero static power; only dynamic and short-circuit power during switching.\n4. Very sharp VTC and large, symmetric noise margins when properly sized ((W/L)_p ≈ (μ_n/μ_p)(W/L)_n).\n5. Infinite DC input resistance, so it can drive and be driven by other CMOS gates without loading effects.",
        "format": "markdown",
        "sha256": "439fc4c943bf0522e00cbe1e8ae367daf665877caffe7594d9804f5f3c596391"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, with an NMOS pull-down and PMOS pull-up, and describes their shared input/output connections and rail-to-rail logic operation. The additional analysis does not undermine the essential answer.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 5481,
        "total_tokens": 5807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3110,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 5481,
        "total_tokens": 5807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3110,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**1. What the circuit actually is**\n\nLook at the symbols: both M1 and M2 are drawn with the arrow on the lower terminal pointing *away* from the device – that is the NMOS symbol in both cases. So this is **not** a CMOS inverter (that would need a PMOS on top). As drawn:\n\n- M1: drain = VDD, gate = Vin, source = Vout → an NMOS **source follower** (common‑drain).\n- M2: drain = Vout, gate = Vin, source = GND → an NMOS **common‑source** stage.\n- Both gates are driven by the same Vin, and the two devices \"fight\" at the output node.\n\n**2. DC (large‑signal) behaviour** (square law, equal VTH, λ = 0, k = μnCox W/L)\n\n*Case Vin < VTH:*  \nM2 is off (VGS2 = Vin < VTH). M1 is also off, because VGS1 = Vin − Vout ≤ Vin < VTH. There is no pull‑up device at all, so Vout is a **floating, high‑impedance node** – it simply holds whatever charge it had (until leakage moves it). There is no defined logic \"1\".\n\n*Case Vin > VTH:*  \nM2 turns on and pulls Vout down. As soon as Vout < Vin − VTH, M1 turns on and sources current. Equilibrium is reached when the two currents are equal. At that point:\n\n- M1 is in saturation: VDS1 = VDD − Vout ≥ Vin − Vout − VTH (always true since Vin ≤ VDD).\n- M2 is in triode: VDS2 = Vout < Vin − VTH (this is exactly the condition for M1 to be on).\n\nEquating currents, with Vov = Vin − VTH and r = k1/k2:\n\n½ k1 (Vov − Vout)² = k2 [Vov·Vout − ½ Vout²]\n\n⇒ (r+1)Vout² − 2(r+1)Vov·Vout + r·Vov² = 0\n\n⇒ **Vout = (Vin − VTH)·(1 − 1/√(1+r))**\n\nFor equal devices (r = 1): **Vout ≈ 0.29 (Vin − VTH)**.\n\nConsequences:\n- The transfer characteristic is **non‑inverting**, with a slope of only ≈0.29 and a threshold offset of VTH.\n- The output can never exceed Vin − VTH ≤ VDD − VTH, no matter how large M1 is made (r → ∞ only gives Vout → Vin − VTH).\n- Example: VDD = 1.8 V, VTH = 0.5 V → with Vin = 1.8 V, Vout ≈ 0.29 × 1.3 ≈ 0.38 V. The \"high\" input gives a lowish output, and the low input gives an undefined output.\n- **Static current** flows whenever Vin > VTH: ID = ½k1·Vov²/(1+r) = ¼k(Vin − VTH)² for equal devices – unlike a CMOS inverter, which draws no DC current in either state.\n- Body effect makes it worse: M1's source sits at Vout > 0, so VTH1 rises, and Vout drops further.\n\n**3. Small‑signal behaviour**\n\nKCL at the output: gm1(vin − vout) − gds1·vout = gm2·vin + gds2·vout\n\nAv = (gm1 − gm2) / (gm1 + gmb1 + gds1 + gds2)\n\nWith M2 in triode: gm2 = k2·VDS2 = k2·Vout, gds2 = k2(Vov − Vout); M1 saturated: gm1 = k1(Vov − Vout). For equal devices at the bias point above: gm1 = 0.707kVov, gm2 = 0.293kVov, gds2 = 0.707kVov, so\n\nAv ≈ (0.707 − 0.293)/(0.707 + 0.707) ≈ **+0.29**\n\n(consistent with the slope of the DC curve; in general Av = 1 − 1/√(1+r)). The output resistance is ≈ 1/(gm1 + gmb1 + gds2) – low, follower‑like. The sign is positive because the follower (M1) wins the small‑signal contest, while the large‑signal level is low because M2 (VGS2 = Vin) is biased much harder than M1 (VGS1 = Vin − Vout).\n\n**4. Verdict**\n\nAs drawn, the circuit is neither an inverter nor a useful buffer: it is a non‑inverting attenuator (gain ≈ 0.3), its output never rises above VDD − VTH (in practice only ≈0.3·(VDD − VTH)), it floats for Vin < VTH, and it burns static power for Vin > VTH.\n\nTo obtain the intended CMOS inverter, M1 must be a **PMOS** with its source at VDD. Then the two devices are complementary: Vin = 0 → M1 on, M2 off, Vout = VDD; Vin = VDD → M1 off, M2 on, Vout = 0; rail‑to‑rail swing, zero static current in either state, and a high‑gain transition region (Av ≈ −(gmn + gmp)(ron ∥ rop)) whose switching point is set by the βn/βp ratio. The figure is a good illustration that the complementary device type, not just the topology, is what makes the CMOS inverter work.",
        "format": "markdown",
        "sha256": "be52d3cb7b0ad414358a4666d7164f5ec1c155860b5e223ee5ae9b9bb82569a1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as NMOS, describes M1 as a source follower and M2 as a pull-down, and concludes the circuit is not a normal CMOS inverter. The additional analysis is consistent with the essential result.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 13720,
        "total_tokens": 14046,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11921,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 13720,
        "total_tokens": 14046,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11921,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nLook at the arrows: on **both** M1 and M2 the arrow sits on the lower terminal and points *out* of the device. Both transistors are therefore **NMOS**, with their sources at the bottom:\n\n| Device | Drain | Gate | Source | Configuration |\n|---|---|---|---|---|\n| M1 | V_DD | V_in | V_out | common‑drain (source follower) |\n| M2 | V_out | V_in | GND | common‑source |\n\nSo this is *not* a CMOS inverter (that would need M1 to be a PMOS with its source at V_DD). It is a source follower and a common‑source stage driven by the same input and sharing the same output node. Each transistor acts as the \"load\" of the other: M2 is an input‑controlled current sink for follower M1, and M1 is an input‑controlled pull‑up for CS stage M2.\n\n## 2. Qualitative operation – two actions that fight each other\n\nWhen V_in rises:\n- M1 (follower) tries to pull V_out **up** (non‑inverting, V_out → V_in − V_TH).\n- M2 (CS) tries to pull V_out **down** (inverting).\n\nThe output is the *difference* of the two effects, so the circuit has very little gain and the sign of the gain depends on the relative strength of M1 and M2.\n\n## 3. Small‑signal analysis\n\nKCL at the output node (no external load):\n\n- Current injected by M1: g_m1(v_in − v_out) − g_mb1·v_out − g_ds1·v_out\n- Current removed by M2: g_m2·v_in + g_ds2·v_out\n\nEquating:\n\n$$\nA_v=\\frac{v_{out}}{v_{in}}=\\frac{g_{m1}-g_{m2}}{g_{m1}+g_{mb1}+g_{ds1}+g_{ds2}}\\;\\approx\\;1-\\frac{g_{m2}}{g_{m1}}\n$$\n\n$$\nR_{out}=\\frac{1}{g_{m1}+g_{mb1}+g_{ds1}+g_{ds2}}\\approx\\frac{1}{g_{m1}}\n$$\n\nInterpretation (superposition): the follower path has gain ≈ +1, while the CS path is loaded by the follower's low output resistance 1/g_m1 and therefore has gain ≈ −g_m2/g_m1. Consequences:\n\n- |A_v| < 1 always – the circuit cannot amplify.\n- g_m1 > g_m2: weak non‑inverting buffer; g_m2 > g_m1: weak inverter; g_m1 = g_m2: output is (to first order) insensitive to the input.\n- Output impedance is low (≈ 1/g_m1), input is purely capacitive.\n\n## 4. Large‑signal (DC) transfer characteristic\n\nLet β_i = μ_nC_ox(W/L)_i, k = β_1/β_2, V_OV = V_in − V_TH (square law, λ = 0, body effect neglected).\n\n**V_in < V_TH:** M2 is off; M1 is also off because V_GS1 = V_in − V_out < V_TH for any V_out ≥ 0. The output node is essentially floating (high impedance) and is held within a few tens of mV of ground only by M2's larger sub‑threshold current. There is no strong \"pull‑down\" state.\n\n**V_in > V_TH:** both devices conduct and the same current flows through them.\n- M1 is always in **saturation** (V_DS1 = V_DD − V_out > V_in − V_out − V_TH).\n- M2 is always in **triode**: because V_GS2 = V_in > V_GS1 = V_in − V_out, M2 has the larger overdrive and must sit in triode to carry the same current (indeed M1 conducts only if V_out < V_OV, which is exactly M2's triode condition).\n\n$$\n\\tfrac{\\beta_1}{2}(V_{OV}-V_{out})^2=\\beta_2\\!\\left(V_{OV}V_{out}-\\tfrac{V_{out}^2}{2}\\right)\n\\;\\Rightarrow\\;(k+1)V_{out}^2-2(k+1)V_{OV}V_{out}+kV_{OV}^2=0\n$$\n\n$$\n\\boxed{V_{out}=\\Bigl(1-\\frac{1}{\\sqrt{k+1}}\\Bigr)(V_{in}-V_{TH})}\n$$\n\nSo above threshold the characteristic is a straight line through (V_TH, 0) with slope 1 − 1/√(k+1):\n\n- equal devices (k = 1): slope ≈ 0.29\n- k = 3: slope = 0.5\n- k → ∞ (M1 very wide): slope → 1, i.e. a plain source follower, V_out → V_in − V_TH\n\n(The slope agrees with the small‑signal expression of Sec. 3 when the triode‑region g_m2 and g_ds2 are inserted.) Body effect on M1 (V_SB1 = V_out) raises V_TH1 and lowers V_out further.\n\nStatic current while V_in > V_TH:\n\n$$\nI_D=\\frac{\\beta_1V_{OV}^2}{2(k+1)}\n$$\n\nMaximum output (V_in = V_DD): V_out,max = (1 − 1/√(k+1))(V_DD − V_TH), e.g. only ≈ 0.29(V_DD − V_TH) for equal devices.\n\n## 5. Conclusions\n\n- The circuit is a **non‑inverting attenuator / level shifter** with a dead zone below V_TH, low output impedance (≈ 1/g_m1), |gain| < 1, and a gain that can be set—or even nulled—by the ratio g_m1/g_m2.\n- As a **logic gate it fails** on every count: it does not invert, the output swing is a small fraction of V_DD, the output is undefined (high‑Z) for a low input, and it burns static current whenever the input is high (a \"ratioed\" circuit).\n- **Contrast with the CMOS inverter:** if M1 is replaced by a PMOS with its source at V_DD, the pull‑up action becomes inverting too, so the two transconductances *add* instead of subtract: A_v = −(g_m1 + g_m2)(r_o1‖r_o2) ≫ 1 near the trip point, rail‑to‑rail swing, and zero static power. The figure is a good illustration of why CMOS logic needs a complementary device rather than an NMOS pull‑up driven by the same input.",
        "format": "markdown",
        "sha256": "fc116e35fb44eee0f8bd65a728f95fa3a0de883e36292ecca313192524121601"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It identifies both devices as NMOS, recognizes the upper source-follower and lower pull-down actions, and concludes this is not a normal CMOS inverter, satisfying the golden full-credit rule.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 22929,
        "total_tokens": 23255,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20749,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 22929,
        "total_tokens": 23255,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20749,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit actually is (don't let the shape fool you)\n\nAt first glance this looks like a CMOS inverter: two stacked devices, gates tied to V<sub>in</sub>, output at the middle. But look at the arrows: **both arrows are on the lower terminal and point outward, so both M<sub>1</sub> and M<sub>2</sub> are NMOS.** For M<sub>1</sub> the source is therefore the *output* node, not V<sub>DD</sub>.\n\n- **M<sub>1</sub>**: gate V<sub>in</sub>, drain V<sub>DD</sub>, source V<sub>out</sub> → a **common‑drain stage (source follower)**\n- **M<sub>2</sub>**: gate V<sub>in</sub>, drain V<sub>out</sub>, source GND → a **common‑source stage**\n\nThe same input drives both, and the two stages share the output node, so each acts as the other's load: a source follower \"fighting\" a common‑source device. (Equivalently, since two series NMOS with a common gate behave like one longer transistor, V<sub>out</sub> is just the channel potential of a single long NMOS tapped at an intermediate point.)\n\n## 2. Large‑signal (DC) behavior\n\n**V<sub>in</sub> < V<sub>TH</sub>:** M<sub>2</sub> is off; M<sub>1</sub> can only pull V<sub>out</sub> up until V<sub>GS1</sub> = V<sub>in</sub> − V<sub>out</sub> drops below V<sub>TH</sub>. Only leakage flows and V<sub>out</sub> sits within tens of millivolts of ground, essentially independent of V<sub>in</sub>.\n\n**V<sub>in</sub> > V<sub>TH</sub>:** M<sub>2</sub> conducts, so M<sub>1</sub> must carry the same current and therefore be on: V<sub>out</sub> < V<sub>in</sub> − V<sub>TH1</sub>. Consequently\n\n- M<sub>2</sub> is in **triode** (V<sub>DS2</sub> = V<sub>out</sub> < V<sub>GS2</sub> − V<sub>TH2</sub>),\n- M<sub>1</sub> is in **saturation** (V<sub>DS1</sub> = V<sub>DD</sub> − V<sub>out</sub> > V<sub>in</sub> − V<sub>out</sub> − V<sub>TH1</sub> for any V<sub>in</sub> ≤ V<sub>DD</sub>).\n\nEquating currents with a square‑law model (β<sub>i</sub> = μ<sub>n</sub>C<sub>ox</sub>(W/L)<sub>i</sub>, V<sub>ov</sub> = V<sub>in</sub> − V<sub>TH</sub>, neglecting λ and body effect):\n\n½β<sub>1</sub>(V<sub>ov</sub> − V<sub>out</sub>)² = β<sub>2</sub>[V<sub>ov</sub>V<sub>out</sub> − ½V<sub>out</sub>²]\n\nSolving (taking the root with V<sub>out</sub> < V<sub>ov</sub>):\n\n**V<sub>out</sub> = α (V<sub>in</sub> − V<sub>TH</sub>),  α = 1 − 1/√(1 + β<sub>1</sub>/β<sub>2</sub>)**\n\n- Equal devices: α = 1 − 1/√2 ≈ 0.29\n- β<sub>1</sub>/β<sub>2</sub> = 3 → α = 0.5; β<sub>1</sub>/β<sub>2</sub> = 8 → α = 0.67\n- α → 1 only if M<sub>1</sub> ≫ M<sub>2</sub> (pure follower), α → 0 if M<sub>2</sub> ≫ M<sub>1</sub>\n\nThe transfer curve is therefore **linear, non‑inverting, with slope < 1**, and the maximum output (at V<sub>in</sub> = V<sub>DD</sub>) is only α(V<sub>DD</sub> − V<sub>TH</sub>), e.g., ≈ 0.4 V for V<sub>DD</sub> = 1.8 V, V<sub>TH</sub> = 0.4 V, equal devices.\n\nSupply current: I<sub>D</sub> = ½ [β<sub>1</sub>β<sub>2</sub>/(β<sub>1</sub>+β<sub>2</sub>)] (V<sub>in</sub> − V<sub>TH</sub>)² — the stack draws current like a single saturated NMOS with (W/L)<sub>1</sub>∥(W/L)<sub>2</sub>. **Static current flows whenever V<sub>in</sub> > V<sub>TH</sub>.**\n\nBody effect (V<sub>SB1</sub> = V<sub>out</sub>) raises V<sub>TH1</sub> above V<sub>TH2</sub>, slightly lowering V<sub>out</sub> and α.\n\n## 3. Small‑signal analysis\n\nModel M<sub>1</sub> with g<sub>m1</sub>, g<sub>mb1</sub>, r<sub>o1</sub>; M<sub>2</sub> in triode with g<sub>m2</sub> = β<sub>2</sub>V<sub>DS2</sub> = β<sub>2</sub>V<sub>out</sub> and g<sub>ds2</sub> = β<sub>2</sub>(V<sub>ov</sub> − V<sub>out</sub>) = 1/R<sub>on2</sub>.\n\nKCL at the output: g<sub>m1</sub>(v<sub>in</sub> − v<sub>out</sub>) − g<sub>mb1</sub>v<sub>out</sub> − v<sub>out</sub>/r<sub>o1</sub> = g<sub>m2</sub>v<sub>in</sub> + g<sub>ds2</sub>v<sub>out</sub>\n\n**A<sub>v</sub> = (g<sub>m1</sub> − g<sub>m2</sub>) / (g<sub>m1</sub> + g<sub>mb1</sub> + g<sub>ds1</sub> + g<sub>ds2</sub>)**\n\nSubstituting the bias point gives back A<sub>v</sub> = 1 − 1/√(1 + β<sub>1</sub>/β<sub>2</sub>) = α (as it must, since the DC curve is linear). Two things push the gain below a normal follower's ≈ 1: M<sub>2</sub>'s triode resistance is a heavy load (g<sub>ds2</sub> is of the same order as g<sub>m1</sub>), and M<sub>2</sub>'s own transconductance pulls the output the *opposite* way (the −g<sub>m2</sub> term).\n\n- **R<sub>out</sub>** = 1/(g<sub>m1</sub> + g<sub>mb1</sub> + g<sub>ds1</sub> + g<sub>ds2</sub>) — low, follower‑like.\n- Input is purely capacitive: C<sub>in</sub> ≈ C<sub>gd1</sub> + C<sub>gs2</sub> + (C<sub>gs1</sub> + C<sub>gd2</sub>)(1 − A<sub>v</sub>); single dominant pole at the output, ω<sub>p</sub> ≈ 1/(R<sub>out</sub>C<sub>L</sub>) — fast.\n\n## 4. Intuitive picture\n\nTwo series NMOS devices with a common gate are one transistor of length L<sub>1</sub>+L<sub>2</sub>. That composite device is in saturation (V<sub>DD</sub> > V<sub>ov</sub>), and the channel potential at a fraction y/L from the source is V<sub>ov</sub>[1 − √(1 − y/L)]. V<sub>out</sub> is simply that tap voltage—for equal devices, the midpoint value 0.29·V<sub>ov</sub>. This explains at once why the output is in phase, linear in V<sub>in</sub>, and always a fixed fraction (< 1) of the overdrive.\n\n## 5. Summary\n\n| Property | This circuit (NMOS/NMOS) | True CMOS inverter (PMOS on top) |\n|---|---|---|\n| Polarity | Non‑inverting | Inverting |\n| Gain | 0 < A<sub>v</sub> = 1 − 1/√(1+β<sub>1</sub>/β<sub>2</sub>) < 1 | −(g<sub>m1</sub>+g<sub>m2</sub>)(r<sub>o1</sub>∥r<sub>o2</sub>) ≫ 1 at trip point |\n| Output swing | 0 … α(V<sub>DD</sub> − V<sub>TH</sub>) | Rail to rail |\n| Static current | Yes, whenever V<sub>in</sub> > V<sub>TH</sub> | ≈ 0 at the rails |\n| Regions | M<sub>1</sub> saturated, M<sub>2</sub> triode | Both saturated near V<sub>DD</sub>/2 |\n\nSo it is neither a logic gate nor a voltage amplifier. It is a **ratiometric attenuator/level shifter with low output impedance**: the attenuation factor α depends only on the device‑size ratio (μ<sub>n</sub>C<sub>ox</sub> cancels), the output is offset by V<sub>TH</sub>, and the circuit is dead (V<sub>out</sub> ≈ 0) for V<sub>in</sub> below threshold. The main lesson: identify each device's type and its configuration (CD vs. CS) before assuming what the topology \"looks like.\"",
        "format": "markdown",
        "sha256": "6bc2e8c3dbc7c2683a39aea255b26cb40e08971b6ef0fb795bedc2463dc38242"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as NMOS, recognizes the upper source-follower and lower pull-down roles, and concludes the circuit is not a normal CMOS inverter. The golden solution’s full-credit rule applies.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 25579,
        "total_tokens": 25905,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22234,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 326,
        "output_tokens": 25579,
        "total_tokens": 25905,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22234,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Circuit identification\n\nThis is a **common‑source (CS) amplifier with a diode‑connected PMOS load** (Razavi, Fig. 3.14‑type stage):\n\n- **M1 (NMOS)** – input device: gate = V<sub>in</sub>, source = ground, drain = V<sub>out</sub>. Converts v<sub>in</sub> to a drain current (transconductance g<sub>m1</sub>).\n- **M2 (PMOS)** – load: source = V<sub>DD</sub>, gate tied to drain (diode‑connected), drain = V<sub>out</sub>. Because V<sub>GS2</sub> = V<sub>DS2</sub>, it is always saturated (if it conducts) and behaves as a two‑terminal nonlinear \"resistor.\"\n\nBoth devices carry the same current: I<sub>D1</sub> = I<sub>D2</sub> = I<sub>D</sub>.\n\n---\n\n## Large‑signal (DC transfer) behavior\n\nThe output sits one PMOS gate‑source drop below V<sub>DD</sub>:\n\n$$V_{out}=V_{DD}-|V_{GS2}| = V_{DD}-|V_{TH2}|-|V_{GS2}-V_{TH2}|$$\n\n- **V<sub>in</sub> < V<sub>TH1</sub>:** M1 off, I<sub>D</sub> ≈ 0, so |V<sub>GS2</sub>| → |V<sub>TH2</sub>| and V<sub>out,max</sub> ≈ V<sub>DD</sub> − |V<sub>TH2</sub>|.\n- **V<sub>in</sub> > V<sub>TH1</sub> (M1 saturated):** equate the currents\n\n$$\\tfrac12\\mu_nC_{ox}\\Big(\\tfrac{W}{L}\\Big)_1(V_{in}-V_{TH1})^2=\\tfrac12\\mu_pC_{ox}\\Big(\\tfrac{W}{L}\\Big)_2(V_{DD}-V_{out}-|V_{TH2}|)^2$$\n\n$$\\Rightarrow\\; V_{out}=V_{DD}-|V_{TH2}|-\\sqrt{\\frac{\\mu_n(W/L)_1}{\\mu_p(W/L)_2}}\\,(V_{in}-V_{TH1})$$\n\n  The transfer curve is a **straight line** – the square‑law of M1 is cancelled by the square‑root law of the diode load, so the stage is intrinsically fairly linear.\n- **M1 enters triode** when V<sub>out</sub> < V<sub>in</sub> − V<sub>TH1</sub>; the gain then collapses. This sets V<sub>out,min</sub> ≈ V<sub>in</sub> − V<sub>TH1</sub>.\n\n---\n\n## Small‑signal analysis\n\nLooking into the drain of the diode‑connected M2 gives an impedance of 1/g<sub>m2</sub> ‖ r<sub>o2</sub>. Writing KCL at the output (v<sub>gs2</sub> = v<sub>out</sub>):\n\n$$-\\,v_{out}\\Big(g_{m2}+\\frac1{r_{o2}}\\Big)=g_{m1}v_{in}+\\frac{v_{out}}{r_{o1}}$$\n\n$$A_v=\\frac{v_{out}}{v_{in}}=-\\,g_{m1}\\left(\\frac1{g_{m2}}\\,\\Big\\|\\,r_{o1}\\,\\Big\\|\\,r_{o2}\\right)\\;\\approx\\;-\\frac{g_{m1}}{g_{m2}}$$\n\n**No body effect:** the PMOS sits in its own n‑well tied to V<sub>DD</sub>, so V<sub>SB2</sub> = 0 and no g<sub>mb2</sub> term appears (unlike the NMOS diode load, where A<sub>v</sub> ≈ −g<sub>m1</sub>/(g<sub>m2</sub>+g<sub>mb2</sub>) = −(g<sub>m1</sub>/g<sub>m2</sub>)·1/(1+η)).\n\nUsing g<sub>m</sub> = √(2µC<sub>ox</sub>(W/L)I<sub>D</sub>) with equal currents:\n\n$$A_v\\approx-\\sqrt{\\frac{\\mu_n(W/L)_1}{\\mu_p(W/L)_2}}$$\n\nEquivalently, with g<sub>m</sub> = 2I<sub>D</sub>/V<sub>ov</sub>:\n\n$$A_v\\approx-\\frac{|V_{GS2}-V_{TH2}|}{V_{GS1}-V_{TH1}}$$\n\nOther small‑signal quantities:\n- R<sub>in</sub> = ∞ (MOS gate)\n- R<sub>out</sub> = 1/g<sub>m2</sub> ‖ r<sub>o1</sub> ‖ r<sub>o2</sub> ≈ 1/g<sub>m2</sub> (low)\n\n---\n\n## Key properties and trade‑offs\n\n**Advantages**\n1. Gain depends only on **mobility ratio and device dimensions**, not on bias current or supply → well‑defined, process‑tolerant, and (to first order) independent of signal level → linear, consistent with the straight‑line DC characteristic.\n2. Compact: no resistors, self‑biased load, no body‑effect degradation.\n3. Low output impedance and a well‑defined output DC level (V<sub>DD</sub> − |V<sub>GS2</sub>|).\n\n**Disadvantages**\n1. **Large gain requires strong device asymmetry.** For |A<sub>v</sub>| = 10 with µ<sub>n</sub> ≈ 2µ<sub>p</sub>, (W/L)<sub>1</sub>/(W/L)<sub>2</sub> ≈ 50.\n2. **Gain costs voltage headroom.** Since |V<sub>ov2</sub>| = |A<sub>v</sub>|·V<sub>ov1</sub>, a gain of 10 with V<sub>ov1</sub> = 200 mV forces |V<sub>GS2</sub> − V<sub>TH2</sub>| = 2 V. The available output swing, roughly from V<sub>in</sub> − V<sub>TH1</sub> up to V<sub>DD</sub> − |V<sub>TH2</sub>|, shrinks as gain increases, so this topology is impractical for high gain in low‑V<sub>DD</sub> processes.\n3. The gain is limited to about g<sub>m1</sub>/g<sub>m2</sub> (typically a few to ~10), far below what a current‑source (active) load can provide (g<sub>m1</sub>(r<sub>o1</sub>‖r<sub>o2</sub>)).\n\nIn summary: a simple, linear, well‑controlled low‑to‑moderate‑gain stage (A<sub>v</sub> ≈ −g<sub>m1</sub>/g<sub>m2</sub>), whose main limitation is the trade‑off between gain and output voltage headroom.",
        "format": "markdown",
        "sha256": "d20cd7abcc5ea6bf3278af58f7ffccd8bd3a58ce7813a05aa9585d4a375343d0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain with channel-length modulation treated consistently, as required for full credit.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 5737,
        "total_tokens": 6531,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3296,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 5737,
        "total_tokens": 6531,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3296,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Common‑Source Stage with a Diode‑Connected PMOS Load\n\n## 1. What the circuit is\n\n| Device | Type | Connections | Role |\n|---|---|---|---|\n| M1 | NMOS | gate = V<sub>in</sub>, source = GND, drain = V<sub>out</sub> | input transconductor (common‑source) |\n| M2 | PMOS | source = V<sub>DD</sub>, gate shorted to drain = V<sub>out</sub> | diode‑connected active load |\n\nThe only current path is V<sub>DD</sub> → M2 → M1 → GND, so I<sub>D1</sub> = I<sub>D2</sub> = I<sub>D</sub>.\nBecause M2's gate is tied to its drain, V<sub>SD2</sub> = V<sub>SG2</sub> > V<sub>SG2</sub> − |V<sub>TH2</sub>|, so **M2 is always in saturation whenever it conducts**. It behaves like a two‑terminal \"square‑law diode\" whose small‑signal resistance is ≈ 1/g<sub>m2</sub>. In other words, this is the resistive‑load CS amplifier with R<sub>D</sub> replaced by a MOSFET – useful because precise, compact resistors are hard to make in CMOS.\n\n## 2. Large‑signal (DC) behaviour\n\nEquating the two square‑law currents (λ neglected):\n\n$$\\tfrac12\\mu_nC_{ox}\\Big(\\tfrac WL\\Big)_1 (V_{in}-V_{TH1})^2=\\tfrac12\\mu_pC_{ox}\\Big(\\tfrac WL\\Big)_2 (V_{DD}-V_{out}-|V_{TH2}|)^2$$\n\n$$\\boxed{V_{out}=V_{DD}-|V_{TH2}|-\\sqrt{\\frac{\\mu_n (W/L)_1}{\\mu_p (W/L)_2}}\\;(V_{in}-V_{TH1})}$$\n\nThree regions of the transfer characteristic:\n\n1. **V<sub>in</sub> < V<sub>TH1</sub>:** M1 off, I<sub>D</sub> → 0, |V<sub>GS2</sub>| → |V<sub>TH2</sub>|, so V<sub>out</sub> ≈ V<sub>DD</sub> − |V<sub>TH2</sub>| (it creeps toward V<sub>DD</sub> only through sub‑threshold conduction). Note the output can never reach V<sub>DD</sub> in normal operation.\n2. **M1 saturated:** V<sub>out</sub> falls **linearly** with V<sub>in</sub> with slope −√(μ<sub>n</sub>(W/L)<sub>1</sub>/μ<sub>p</sub>(W/L)<sub>2</sub>). A linear V<sub>out</sub>–V<sub>in</sub> characteristic is a distinctive property of a square‑law device driving a square‑law diode load (high linearity).\n3. **M1 in triode** when V<sub>out</sub> ≤ V<sub>in</sub> − V<sub>TH1</sub>, i.e. when\n\n$$V_{in}-V_{TH1}=\\frac{V_{DD}-|V_{TH2}|}{1+\\sqrt{\\mu_n(W/L)_1/\\mu_p(W/L)_2}}$$\n\n   Beyond this the gain collapses and V<sub>out</sub> settles to a small value.\n\nBias point: V<sub>out,DC</sub> = V<sub>DD</sub> − |V<sub>TH2</sub>| − |V<sub>ov2</sub>|, where |V<sub>ov2</sub>| = √(2I<sub>D</sub>/μ<sub>p</sub>C<sub>ox</sub>(W/L)<sub>2</sub>).\n\n## 3. Small‑signal analysis\n\nThe diode‑connected PMOS presents an impedance (1/g<sub>m2</sub>) ∥ r<sub>o2</sub> from the output to AC ground. There is **no g<sub>mb2</sub> term**: in an n‑well process the body of M2 is tied to V<sub>DD</sub> together with its source, so V<sub>SB2</sub> = 0 and the body effect is eliminated (unlike an NMOS diode load, where the gain is reduced by 1/(1+η)).\n\n$$A_v=-g_{m1}\\Big(\\frac1{g_{m2}}\\,\\Big\\|\\,r_{o1}\\,\\Big\\|\\,r_{o2}\\Big)=-\\frac{g_{m1}}{g_{m2}+g_{ds1}+g_{ds2}}\\;\\approx\\;-\\frac{g_{m1}}{g_{m2}}$$\n\nUsing g<sub>m</sub> = √(2μC<sub>ox</sub>(W/L)I<sub>D</sub>) with equal currents:\n\n$$A_v\\approx-\\sqrt{\\frac{\\mu_n (W/L)_1}{\\mu_p (W/L)_2}}$$\n\nUsing g<sub>m</sub> = 2I<sub>D</sub>/V<sub>ov</sub>:\n\n$$A_v\\approx-\\frac{|V_{GS2}-V_{TH2}|}{V_{GS1}-V_{TH1}}=-\\frac{|V_{ov2}|}{V_{ov1}}$$\n\nOther small‑signal quantities:\n\n- R<sub>out</sub> = (1/g<sub>m2</sub>) ∥ r<sub>o1</sub> ∥ r<sub>o2</sub> ≈ 1/g<sub>m2</sub> (low)\n- R<sub>in</sub> = ∞ at DC; C<sub>in</sub> ≈ C<sub>GS1</sub> + (1 + |A<sub>v</sub>|)C<sub>GD1</sub> (Miller)\n- Output pole ω<sub>p</sub> ≈ g<sub>m2</sub>/C<sub>out</sub> → wide bandwidth because the output node is low‑impedance\n- Supply rejection is poor: v<sub>out</sub>/v<sub>dd</sub> ≈ g<sub>m2</sub>r<sub>o1</sub>/(1 + g<sub>m2</sub>r<sub>o1</sub>) ≈ 1, i.e. the output essentially rides on V<sub>DD</sub>.\n- Input‑referred thermal noise ≈ 4kTγ(1/g<sub>m1</sub>)(1 + g<sub>m2</sub>/g<sub>m1</sub>) – the load adds noise but is attenuated by the gain.\n\n## 4. Properties and design trade‑offs\n\n**Advantages**\n- Gain is set by a *ratio* of geometries (and μ<sub>n</sub>/μ<sub>p</sub>), so it is nearly independent of I<sub>D</sub>, V<sub>DD</sub>, temperature and process – and constant over the whole saturation region (linear).\n- No body effect in the load (PMOS in its own n‑well).\n- Since μ<sub>p</sub> < μ<sub>n</sub>, a given gain needs a smaller size ratio than an NMOS diode load: (W/L)<sub>1</sub>/(W/L)<sub>2</sub> = A<sub>v</sub>²·μ<sub>p</sub>/μ<sub>n</sub> (e.g. A<sub>v</sub> = 10, μ<sub>n</sub> ≈ 2μ<sub>p</sub> → ratio 50 instead of 100).\n- No resistors, low output impedance, high speed.\n\n**Disadvantages**\n- **Gain–headroom conflict.** A<sub>v</sub> = |V<sub>ov2</sub>|/V<sub>ov1</sub>: for A<sub>v</sub> = 10 with V<sub>ov1</sub> = 0.2 V you would need |V<sub>ov2</sub>| = 2 V, which no modern supply allows. Practical gains are only ≈ 2–5.\n- Limited output swing: V<sub>out,max</sub> ≈ V<sub>DD</sub> − |V<sub>TH2</sub>|, V<sub>out,min</sub> ≈ V<sub>ov1</sub>, and a large |V<sub>ov2</sub>| eats into the available range.\n- High gain demands a very wide M1 and a very narrow M2 → large input capacitance, awkward layout.\n- Poor PSRR from V<sub>DD</sub>.\n\n**Common improvement:** place a constant current source in parallel with M2 so it carries most of I<sub>D1</sub> (e.g. 75 %). M2 then conducts only a fraction of the current, so for the same device sizes g<sub>m2</sub> drops (gain ↑, doubling for I<sub>D2</sub> = 0.25 I<sub>D1</sub>) and for the same gain |V<sub>ov2</sub>| shrinks (headroom ↑).\n\n**Summary:** the figure is a common‑source amplifier with a diode‑connected PMOS active load. Its gain is ≈ −g<sub>m1</sub>/g<sub>m2</sub> = −√(μ<sub>n</sub>(W/L)<sub>1</sub>/μ<sub>p</sub>(W/L)<sub>2</sub>) = −|V<sub>ov2</sub>|/V<sub>ov1</sub>, its output resistance is ≈ 1/g<sub>m2</sub>, and it offers well‑defined, linear, wideband but low gain at the cost of output swing.",
        "format": "markdown",
        "sha256": "2db3addef14e612eb7d4c440fc45ca34fbf778d47ac7931bfcd2552e5addf4a1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain with channel-length modulation included consistently for both devices.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 14325,
        "total_tokens": 15119,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11024,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 14325,
        "total_tokens": 15119,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11024,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Circuit identification\n\nThe figure is a **common‑source (CS) amplifier with a diode‑connected PMOS load** (the classic Razavi Fig. 3.13‑type stage).\n\n| Device | Type | Connections | Role |\n|---|---|---|---|\n| M1 | NMOS | Gate = V_in, Source = GND, Drain = V_out | Input / transconductance device |\n| M2 | PMOS | Source = V_DD, Gate shorted to Drain = V_out | Active (diode‑connected) load |\n\nBecause gate and drain of M2 are tied together, V_GS2 = V_DS2, so M2 is **always in saturation** when it conducts (|V_DS| = |V_GS| > |V_GS| − |V_TH|). Both transistors carry the same current I_D.\n\n---\n\n## 1. Large‑signal (DC) behavior\n\n**V_in < V_TH1:** M1 is off, I_D = 0. M2 pulls V_out up until it just turns off:\n\n  V_out ≈ V_DD − |V_TH2|\n\n(The output can never reach V_DD; a PMOS diode always \"loses\" one threshold.)\n\n**V_in > V_TH1, M1 in saturation:** Equating currents (neglecting λ):\n\n  ½ μ_n C_ox (W/L)₁ (V_in − V_TH1)² = ½ μ_p C_ox (W/L)₂ (V_DD − V_out − |V_TH2|)²\n\nTaking the square root:\n\n  **V_out = V_DD − |V_TH2| − √[μ_n(W/L)₁ / (μ_p(W/L)₂)] · (V_in − V_TH1)**\n\nSo V_out is a **linear** function of V_in in this region – a nice property for linearity. The slope (the gain) is set only by geometry and mobility ratio.\n\n**Large V_in:** when V_out falls below V_in − V_TH1, M1 enters triode and the gain collapses. The lowest output voltage for which the stage is still \"linear\" is V_out,min ≈ V_GS1 − V_TH1 = V_ov1.\n\n---\n\n## 2. Small‑signal analysis\n\n**Diode‑connected load:** Apply a test voltage v_x at the drain/gate node of M2: i_x = g_m2·v_x + v_x/r_o2 → the load looks like a resistor\n\n  R_load = (1/g_m2) ‖ r_o2 ≈ 1/g_m2\n\nNo body effect appears because the source of M2 is at V_DD and its n‑well is normally tied to V_DD (unlike an NMOS diode load, where g_mb would degrade the gain).\n\n**Gain:**\n\n  A_v = −g_m1 · (1/g_m2 ‖ r_o1 ‖ r_o2) ≈ **−g_m1 / g_m2**\n\nUsing g_m = √(2 μ C_ox (W/L) I_D) with equal currents:\n\n  **A_v ≈ −√[ μ_n (W/L)₁ / (μ_p (W/L)₂) ]**\n\nEquivalently, using g_m = 2I_D/V_ov:\n\n  **A_v ≈ −(|V_GS2| − |V_TH2|) / (V_GS1 − V_TH1) = −V_ov2 / V_ov1**\n\n**Output resistance:** R_out = 1/g_m2 ‖ r_o1 ‖ r_o2 ≈ 1/g_m2 (low).\n\n---\n\n## 3. Properties and trade‑offs\n\n1. **Well‑defined, bias‑independent gain.** To first order the gain depends on neither I_D, V_DD, nor temperature (only on dimension ratios and μ_n/μ_p) – attractive for a matched IC design.\n\n2. **Low gain for reasonable area.** Since μ_n/μ_p ≈ 2–3, a gain of 10 requires (W/L)₁/(W/L)₂ ≈ 33–50 – a large area penalty.\n\n3. **Gain versus output swing.** A gain |A_v| forces V_ov2 = |A_v|·V_ov1. For example, V_ov1 = 0.2 V and |A_v| = 10 would require |V_GS2| − |V_TH2| = 2 V dropped across the load – consuming most of the supply. The usable output range is roughly from V_DD − |V_TH2| (top) down to V_ov1 (bottom), and a high gain eats into this range from the top.\n\n4. **Channel‑length modulation** has little effect, since 1/g_m2 ≪ r_o1, r_o2.\n\n5. **Low output impedance (≈1/g_m2)** limits the gain but gives a high‑frequency output pole – diode‑connected loads are popular in wideband/high‑speed stages.\n\n6. **Compared with an NMOS diode load**, the PMOS version avoids body effect (gain −g_m1/g_m2 instead of −g_m1/(g_m2+g_mb2)).\n\n---\n\n## Summary\n\nThe circuit is an inverting CS amplifier whose load is a PMOS \"diode\" with small‑signal resistance 1/g_m2. Its gain is\n\n  A_v ≈ −g_m1/g_m2 = −√[μ_n(W/L)₁ / (μ_p(W/L)₂)] = −V_ov2/V_ov1,\n\nwith a linear V_out–V_in characteristic, process‑insensitive gain, low output resistance, but a fundamental trade‑off between gain, device‑size ratio, and output voltage headroom.",
        "format": "markdown",
        "sha256": "0e910a66afbce52d4871582f6feb2c734dad89ef6d8cf40dc91b1a249d8760e2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain with both devices’ output resistances included, as well as the valid −gm1/gm2 approximation. The other large-signal details are secondary to the required answer.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 6548,
        "total_tokens": 7342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4704,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 794,
        "output_tokens": 6548,
        "total_tokens": 7342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4704,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Recognizing the topology\n\n| Device | Type | Source | Gate | Drain | Role |\n|---|---|---|---|---|---|\n| M₂ | PMOS | V_DD (AC ground) | V_in | V_out | Common‑source amplifying device |\n| M₁ | PMOS | V_out | ground | ground | Diode‑connected load (gate shorted to drain) |\n\nSo this is a **common‑source stage with a diode‑connected load**, built entirely with PMOS devices (the \"complement\" of the familiar NMOS‑CS / NMOS‑diode load). M₂ converts v_in into a drain current; that current flows through M₁, which behaves as a resistor of roughly 1/g_m1.\n\nNote that M₁ is always in saturation when it conducts, because V_SD1 = V_SG1 > V_SG1 − |V_TH1|.\n\n## 2. Large‑signal (bias) analysis (λ = 0)\n\nBoth transistors carry the same current I_D:\n\nI_D = ½ μ_pC_ox (W/L)₂ (V_DD − V_in − |V_TH2|)²\n\nV_out = V_SG1 = |V_TH1| + √( 2I_D / (μ_pC_ox (W/L)₁) )\n\nCombining:\n\n**V_out = |V_TH1| + √[(W/L)₂/(W/L)₁] · (V_DD − V_in − |V_TH2|)**\n\n- The transfer characteristic is a straight line with slope −√[(W/L)₂/(W/L)₁] → the stage is inherently fairly linear.\n- Conditions: M₂ on requires V_in < V_DD − |V_TH2|; M₂ saturated requires V_SD2 ≥ V_SG2 − |V_TH2|, i.e. **V_out ≤ V_in + |V_TH2|** (equivalently V_out ≤ V_DD − V_OD2).\n- As V_in → V_DD − |V_TH2|, I_D → 0 and V_out falls to ≈ |V_TH1| (the diode load cannot drop less than one threshold). Hence the output swing is roughly |V_TH1| ≤ V_out ≤ V_DD − V_OD2.\n\n## 3. Small‑signal analysis\n\nSmall‑signal model: M₂ → current source g_m2·v_gs2 (v_gs2 = v_in, since its source is at AC ground) in parallel with r_O2; M₁ (diode‑connected) → resistance (1/g_m1) ∥ r_O1 from the output node to ground.\n\nKCL at the output node:\n\ng_m2·v_in + v_out/r_O2 + g_m1·v_out + v_out/r_O1 = 0\n\n**A_v = v_out / v_in = − g_m2 · ( r_O2 ∥ r_O1 ∥ 1/g_m1 )**\n\nWith channel‑length modulation neglected (λ = 0):\n\nA_v = − g_m2/g_m1 = − √[(W/L)₂/(W/L)₁] = − V_OD1/V_OD2\n\n(the last form uses g_m = 2I_D/V_OD with equal currents). This agrees with the slope of the large‑signal characteristic found above.\n\n## 4. Impedances\n\n- Input impedance: R_in = ∞ (gate of M₂).\n- Output impedance: **R_out = r_O2 ∥ r_O1 ∥ 1/g_m1 ≈ 1/g_m1** (low, set by the diode load).\n\n## 5. Remarks\n\n- The gain depends only on a ratio of device dimensions (or overdrive voltages), so it is well‑defined and relatively insensitive to process and temperature — the main attraction of a diode‑connected load. The price is a modest gain (typically a few V/V) and a lower output level that cannot drop below ≈ |V_TH1|.\n- The sign is negative: the stage inverts (raising V_in reduces the overdrive of M₂, lowers I_D, and V_out falls).\n- If M₁'s n‑well is tied to V_DD rather than to its source, body effect appears in M₁ (V_SB ≠ 0); the load impedance then becomes 1/(g_m1 + g_mb1) ∥ r_O1 and the gain magnitude is slightly reduced: A_v = −g_m2 [r_O2 ∥ r_O1 ∥ 1/(g_m1+g_mb1)]. M₂ has no body effect since its source sits at V_DD.",
        "format": "markdown",
        "sha256": "ee359c24fd14633be17be87f03bb484bccf3be95b8191c744c6f6fd72f94f625"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, M₂ as the common-source input device, and M₁ as a diode-connected PMOS load with gate and drain grounded; it gives the expected gm/gm gain, Av ≈ −gm₂/gm₁.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 10627,
        "total_tokens": 12477,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9126,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 10627,
        "total_tokens": 12477,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9126,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nBoth devices are PMOS transistors (source arrows point into the channel):\n\n| Device | Source | Gate | Drain | Role |\n|---|---|---|---|---|\n| M₂ | V_DD | V_in | V_out | Common‑source input (gain) device |\n| M₁ | V_out | GND | GND | Gate and drain tied together → **diode‑connected load** |\n\nThe bias current flows V_DD → M₂ → V_out node → M₁ → ground.\nSo this is a **PMOS common‑source amplifier with a diode‑connected PMOS load** – the complement of the familiar NMOS CS stage with a diode‑connected NMOS load.\n\n## 2. Large‑signal (DC) behaviour\n\n- M₁: V_SG1 = V_SD1 = V_out ⇒ as soon as it conducts (V_out > |V_TH1|) it is automatically in saturation:\n  I_D = ½ μ_pC_ox (W/L)₁ (V_out − |V_TH1|)²\n- M₂: V_SG2 = V_DD − V_in. It is on for V_in < V_DD − |V_TH2|, and in saturation if\n  V_SD2 ≥ V_SG2 − |V_TH2| ⇔ V_out ≤ V_in + |V_TH2|.\n\nEquating the two currents (both in saturation, λ = 0):\n\n$$V_{out}= |V_{TH1}| + \\sqrt{\\frac{(W/L)_2}{(W/L)_1}}\\;\\bigl(V_{DD}-|V_{TH2}|-V_{in}\\bigr)$$\n\nTransfer characteristic:\n- V_in > V_DD − |V_TH2|: M₂ off, no current, V_out falls to ≈ |V_TH1| (toward 0 via sub‑threshold conduction).\n- Lower V_in: M₂ turns on; V_out rises **linearly** with slope −√[(W/L)₂/(W/L)₁].\n- Still lower V_in (V_out reaches V_in + |V_TH2|): M₂ enters the triode region and the slope collapses.\n\nThe stage is inverting, and in its useful region the characteristic is nearly a straight line.\n\n## 3. Small‑signal gain\n\nSmall‑signal model: M₂ is a current source g_m2·v_in (plus r_o2) driving the impedance of diode‑connected M₁, which is (1/(g_m1+g_mb1)) ‖ r_o1.\n\nKCL at the output node:\n\n$$g_{m2}v_{in} + v_{out}\\Bigl(g_{m1}+g_{mb1}+\\frac{1}{r_{o1}}+\\frac{1}{r_{o2}}\\Bigr)=0$$\n\n$$A_v=\\frac{v_{out}}{v_{in}}=-g_{m2}\\Bigl[\\frac{1}{g_{m1}+g_{mb1}}\\,\\Big\\|\\,r_{o1}\\,\\Big\\|\\,r_{o2}\\Bigr]$$\n\nNeglecting channel‑length modulation and body effect (λ = 0, γ = 0):\n\n$$A_v\\approx-\\frac{g_{m2}}{g_{m1}}=-\\sqrt{\\frac{(W/L)_2}{(W/L)_1}}=-\\frac{V_{ov1}}{V_{ov2}}$$\n\n(the second forms follow because both transistors are PMOS, so μ_pC_ox cancels, and they carry the same I_D).\n\n## 4. Impedances\n\n- R_in = ∞ (gate of M₂, at low frequency)\n- R_out = (1/(g_m1+g_mb1)) ‖ r_o1 ‖ r_o2 ≈ 1/g_m1 (low)\n\n## 5. Observations / design trade‑offs\n\n1. **Well‑defined gain:** |A_v| depends only on a ratio of device dimensions – insensitive to process (μ_p, V_TH), temperature and bias current. That is the main attraction of a same‑type diode‑connected load.\n2. **Gain vs. headroom:** |A_v| = V_ov1/V_ov2, so a large gain needs a large overdrive on M₁. The DC output sits at V_out = |V_TH1| + V_ov1 = |V_TH1| + |A_v|·V_ov2, and M₂ saturation requires V_out ≤ V_DD − V_ov2. Hence |A_v| ≲ (V_DD − |V_TH1| − V_ov2)/V_ov2 – practically only a few V/V, and the output can't swing below ≈|V_TH1|.\n3. **Body effect:** M₂ has V_SB = 0. M₁'s source is at V_out, so if its n‑well is tied to V_DD it suffers body effect, reducing the gain by ≈1/(1+η) and adding nonlinearity; tying M₁'s well to its source removes this.\n4. **Linearity:** because g_m2/g_m1 is bias‑independent, the small‑signal gain is essentially constant across the saturation region (the straight line in §2), giving good linearity compared with a resistive or current‑source load.\n5. Low R_out (≈1/g_m1) means the stage can drive moderate loads with little gain loss, and the output pole is at a relatively high frequency.",
        "format": "markdown",
        "sha256": "ce372e460fb2fa6c44e31cd1580cbc53ad3912016bd4349637bd336d85acbe10"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, M2 as the common-source input device, and M1 as a diode-connected PMOS load with gate and drain at ground. It gives the required gm/gm gain, Av ≈ −gm2/gm1.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 12937,
        "total_tokens": 14787,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11149,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 12937,
        "total_tokens": 14787,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11149,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Recognizing the circuit\n\nBoth symbols have the source arrow pointing *into* the device at the top terminal, so **both transistors are PMOS**:\n\n| Device | Source | Gate | Drain | Role |\n|---|---|---|---|---|\n| M₂ | V_DD | V_in | V_out | Common‑source amplifying device |\n| M₁ | V_out | Ground | Ground | Diode‑connected load (gate tied to drain) |\n\nSo this is a **PMOS common‑source stage with a diode‑connected PMOS load**. The same drain current I_D flows through both devices.\n\n## 2. Large‑signal (DC) behaviour\n\nM₁ has V_SG1 = V_SD1 = V_out, so it is always in saturation when on (V_SD ≥ V_SG − |V_TH| is automatically satisfied). Neglecting channel‑length modulation:\n\n- M₂: I_D = ½ μ_pC_ox (W/L)₂ (V_DD − V_in − |V_TH|)²  \n- M₁: I_D = ½ μ_pC_ox (W/L)₁ (V_out − |V_TH|)²\n\nEquating the two currents:\n\n$$V_{out} = |V_{TH}| + \\sqrt{\\frac{(W/L)_2}{(W/L)_1}}\\,\\big(V_{DD} - V_{in} - |V_{TH}|\\big)$$\n\n→ the transfer characteristic is a straight line with negative slope while both devices are saturated.\n\nOperating limits:\n- M₂ stays saturated if V_SD2 ≥ V_SG2 − |V_TH| ⇒ **V_out ≤ V_in + |V_TH|** (upper swing limit).\n- M₁ conducts only if **V_out ≥ |V_TH|** (lower limit; this is the headroom \"cost\" of a diode load).\n- If V_in > V_DD − |V_TH|, M₂ turns off, I_D → 0 and V_out collapses to ≈ |V_TH|.\n\n## 3. Small‑signal analysis\n\nWith V_DD as ac ground:\n\n- M₂: v_gs2 = v_in, so a current g_m2·v_in flows from the output node toward ac ground (through the dependent source), in parallel with r_o2.\n- M₁: v_gs1 = 0 − v_out, so its dependent source sinks g_m1·v_out from the output node; together with r_o1 it is just a resistor (1/g_m1) ∥ r_o1 to ground.\n\nKCL at V_out:\n\n$$g_{m2}v_{in} + g_{m1}v_{out} + \\frac{v_{out}}{r_{o1}} + \\frac{v_{out}}{r_{o2}} = 0$$\n\n$$\\boxed{A_v = \\frac{v_{out}}{v_{in}} = -\\,g_{m2}\\left(\\frac{1}{g_{m1}}\\;\\Big\\|\\;r_{o1}\\;\\Big\\|\\;r_{o2}\\right)}$$\n\nWith λ = 0 (r_o → ∞):\n\n$$A_v = -\\frac{g_{m2}}{g_{m1}} = -\\sqrt{\\frac{(W/L)_2}{(W/L)_1}} = -\\frac{V_{SG1}-|V_{TH}|}{V_{SG2}-|V_{TH}|}$$\n\n(μ_p cancels because both devices are p‑channel and carry the same current.)\n\n**Impedances**\n- R_in = ∞ (gate input).\n- R_out = (1/g_m1) ∥ r_o1 ∥ r_o2 ≈ 1/g_m1 — relatively low.\n\n**Body effect:** if M₁ sits in the common n‑well tied to V_DD, its source (V_out) is not at the body potential, so g_mb1 appears in parallel:  \nA_v ≈ −g_m2 /(g_m1 + g_mb1) = −(1/(1+η))·√[(W/L)₂/(W/L)₁]. If M₁ has its own well tied to its source, this term disappears.\n\n## 4. Observations\n\n- **Inverting amplifier**: raising V_in reduces V_SG2 → less current → less V_SG1 = V_out.\n- **Gain is set by a geometry ratio**, essentially independent of process, temperature and bias current — the main attraction of a diode‑connected load. The price is a low, modest gain and the fact that r_o and body effect make it slightly smaller than the ideal ratio.\n- **Swing trade‑off**: a large gain requires a small (W/L)₁, i.e., a large overdrive on M₁, which raises the minimum V_out (= |V_TH| + V_OV1) and eats into the output range (|V_TH| + V_OV1 ≤ V_out ≤ V_in + |V_TH|).\n- Low R_out (≈1/g_m1) means the stage is fairly insensitive to loading but cannot deliver the high gain of a current‑source‑loaded CS stage.",
        "format": "markdown",
        "sha256": "76ae0614edf1adfed4eff1fc0b8af53a703b7022d869084f294a48475601fc08"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both PMOS devices, M2 as the common-source input device, and M1 as a diode-connected PMOS load with gate/drain at ground; it also gives the required gm/gm gain, Av ≈ −gm2/gm1.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 10111,
        "total_tokens": 11961,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8437,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1850,
        "output_tokens": 10111,
        "total_tokens": 11961,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8437,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the small-signal model**\n\n- M2: its gate (V_b2) and source (V_DD) are both at AC ground, so g_m2·v_gs2 = 0 and M2 simply looks like a resistor r_O2 between node X and ground.\n- M1: gate at AC ground (V_b1), source at node X. From the output, M1 is therefore a transistor with source degeneration R_S = r_O2.\n\n**Derivation**\n\nApply a test voltage v_t at the output and let the current i_t flow into the drain of M1:\n\n1. All of i_t flows through r_O2, so v_X = i_t·r_O2.\n2. With the gate (and bulk) at ground, v_gs1 = v_bs1 = −i_t·r_O2.\n3. KCL at the drain of M1: the current through r_O1 is  \n   i_t − g_m1 v_gs1 − g_mb1 v_bs1 = i_t[1 + (g_m1 + g_mb1) r_O2]\n4. Then  \n   v_t = v_X + r_O1·i_t[1 + (g_m1 + g_mb1) r_O2]\n\n**Result**\n\n$$\nR_{out}=\\frac{v_t}{i_t}=\\big[1+(g_{m1}+g_{mb1})\\,r_{O1}\\big]\\,r_{O2}+r_{O1}\n$$\n\nNeglecting body effect and assuming g_m r_O ≫ 1:\n\n$$\nR_{out}\\approx g_{m1}\\,r_{O1}\\,r_{O2}\n$$\n\nThat is, M1 \"boosts\" the output resistance r_O2 of the current source M2 by the factor g_m1 r_O1 (the intrinsic gain of M1) — the hallmark of a cascode current source.",
        "format": "markdown",
        "sha256": "0c92d9089ef1462b68e4cf83f4ca927b6afd4efa4707a432500337ba5c697928"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Identifies M1 as the cascode device and derives the correct full output-resistance expression and approximation; the device-type detail is not required by the full-credit rule.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 1850,
        "total_tokens": 4677,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1265,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 1850,
        "total_tokens": 4677,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1265,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the small‑signal picture**\n\n- Both gates are held at constant bias voltages, so in the small‑signal model $V_{b1}$, $V_{b2}$ and $V_{DD}$ are all AC ground.\n- $M_2$ therefore has its gate and source both at AC ground → its dependent source $g_{m2}v_{gs2}=0$, and $M_2$ simply looks like a resistor $r_{O2}$ connected from node $X$ to ground.\n- $M_1$ is then a transistor whose source is degenerated by $R_S = r_{O2}$, and we look into its drain.\n\n**Output resistance of a degenerated transistor**\n\nApply a test voltage $v_t$ at the drain of $M_1$ and find $i_t$:\n\n- $i_t$ flows through $r_{O2}$, so $v_X = i_t\\,r_{O2}$ (source of $M_1$).\n- $v_{gs1} = 0 - v_X = -i_t r_{O2}$, so $g_{m1}v_{gs1} = -g_{m1} r_{O2}\\, i_t$.\n- KCL at the drain: the current through $r_{O1}$ is $i_t - g_{m1}v_{gs1} = i_t(1+g_{m1}r_{O2})$.\n- KVL: $v_t = v_X + r_{O1}\\,i_t(1+g_{m1}r_{O2}) = i_t\\big[r_{O2} + r_{O1} + g_{m1}r_{O1}r_{O2}\\big]$\n\n**Result**\n\n$$\nR_{out} = \\frac{v_t}{i_t} = (1 + g_{m1}r_{O1})\\,r_{O2} + r_{O1} \\;\\approx\\; g_{m1}\\,r_{O1}\\,r_{O2}\n$$\n\n(If body effect of $M_1$ is included, replace $g_{m1}$ by $g_{m1}+g_{mb1}$: $R_{out} = [1+(g_{m1}+g_{mb1})r_{O1}]\\,r_{O2} + r_{O1}$.)\n\nSo the cascode device $M_1$ boosts the output resistance of the current source $M_2$ by roughly the factor $g_{m1}r_{O1}$ (the intrinsic gain of $M_1$).",
        "format": "markdown",
        "sha256": "7dcbb616e9f49dc2c7f27282aa8e48579a54cdee97eb8ae57e5569a5ba927c69"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the cascode device and derives the correct output resistance, including the optional body-effect term. The golden solution allows full credit without explicitly naming both devices as PMOS.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 1549,
        "total_tokens": 4376,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 1549,
        "total_tokens": 4376,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the small‑signal picture**\n\n- M₂: its gate (V_b2) and source (V_DD) are both at ac ground, so its g_m generator carries no current → M₂ simply appears as a resistor **r_O2** from node X to ac ground.\n- M₁: gate at ac ground, source at X, drain = output. It is therefore a common‑gate device whose source is degenerated by R_S = r_O2.\n\n**Calculation**\n\nApply a test voltage v_t at the output and let i_t flow into the drain of M₁. All of i_t flows through r_O2, so\n\nv_X = i_t·r_O2  and  v_gs1 = 0 − v_X = −i_t r_O2\n\nKCL at the drain of M₁ (current through r_O1 plus the g_m source):\n\ni_t = (v_t − v_X)/r_O1 + g_m1 v_gs1\ni_t = (v_t − i_t r_O2)/r_O1 − g_m1 i_t r_O2\n\nv_t = i_t ( r_O1 + r_O2 + g_m1 r_O1 r_O2 )\n\n**Result**\n\nR_out = (1 + g_m1 r_O1) r_O2 + r_O1 ≈ g_m1 r_O1 r_O2\n\n(If the body effect of M₁ is included, since its bulk is tied to V_DD while its source sits at X:\n\nR_out = [1 + (g_m1 + g_mb1) r_O1] r_O2 + r_O1 ≈ (g_m1 + g_mb1) r_O1 r_O2 .)\n\nSo the cascode device M₁ \"boosts\" the output resistance of the current source M₂ from r_O2 to roughly g_m1 r_O1 · r_O2 — a factor of about g_m1 r_O1 (the intrinsic gain of M₁) higher.",
        "format": "markdown",
        "sha256": "07b10537f3d67230ca1d23c6a2891ae051e57742ab5109eb2ce38a4b255b9279"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate cascode and gives the correct output-resistance expression and approximation; including body effect is optional.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 3192,
        "total_tokens": 6019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2582,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2827,
        "output_tokens": 3192,
        "total_tokens": 6019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2582,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Key idea:** M2 is a PMOS whose source is at V_DD, gate at V_b2 and drain at node X. A PMOS stays in saturation as long as its drain does not rise above its gate by more than one threshold:\n\n$$|V_{DS2}| \\ge |V_{GS2}| - |V_{TH2}| \\;\\;\\Longrightarrow\\;\\; V_{DD}-V_X \\ge (V_{DD}-V_{b2})-|V_{TH2}|$$\n\n$$\\boxed{V_X \\le V_{b2}+|V_{TH2}|}$$\n\n(equivalently, V_X must stay at least one overdrive, |V_GS2 − V_TH2|, below V_DD).\n\n**What sets V_X?** M1 does. Since the current through the stack is fixed, M1 needs a definite |V_GS1| (= |V_TH1| + √(2I/(μ_pC_ox(W/L)_1))), and its source voltage is\n\n$$V_X = V_{b1} + |V_{GS1}|$$\n\n**Design condition:** substitute into the inequality:\n\n$$V_{b1} + |V_{GS1}| \\le V_{b2} + |V_{TH2}| \\quad\\Longrightarrow\\quad V_{b1} \\le V_{b2} + |V_{TH2}| - |V_{GS1}|$$\n\nSo we ensure M2's saturation by choosing the bias voltages properly: V_b1 must be low enough (or V_b2 high enough) that M1's source (node X) is not pulled above V_b2 + |V_TH2|. Of course V_b2 must also be below V_DD − |V_TH2| so that M2 is on.\n\n**Remark on swing:** If we pick V_b1 at the limit, V_b1 = V_b2 + |V_TH2| − |V_GS1|, then M2 sits at the edge of saturation with V_X = V_DD − |V_GS2 − V_TH2|, and M1 (which needs V_out ≤ V_X − |V_GS1 − V_TH1| = V_b1 + |V_TH1|) allows the output to rise as high as\n\n$$V_{out,max} = V_{DD} - |V_{GS2}-V_{TH2}| - |V_{GS1}-V_{TH1}|,$$\n\ni.e., only two overdrive voltages below V_DD—the maximum possible voltage headroom for this cascode current source.",
        "format": "markdown",
        "sha256": "f5937c9806600458fab51d6834999f716d1672bc9211ee2322572a253a6d0255"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS saturation condition for M2, relates VX to Vb1 through M1, and derives the resulting bias constraint. The additional headroom discussion is consistent with the circuit conditions.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3205,
        "total_tokens": 5996,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2402,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3205,
        "total_tokens": 5996,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2402,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Set‑up.** In this PMOS cascode current source, M2 is the \"main\" current source (source at V_DD, gate at V_b2, drain at node X), and M1 is the cascode device whose gate voltage V_b1 fixes the voltage at X.\n\n**Saturation condition for a PMOS.** A PMOS is saturated when its drain is no higher than one threshold above its gate:\n\n$$V_{SD2}\\ \\ge\\ V_{SG2}-|V_{TH2}|$$\n\nWith V_SD2 = V_DD − V_X and V_SG2 = V_DD − V_b2:\n\n$$V_{DD}-V_X \\ \\ge\\ V_{DD}-V_{b2}-|V_{TH2}| \\quad\\Longrightarrow\\quad V_X \\ \\le\\ V_{b2}+|V_{TH2}|$$\n\n(equivalently, V_X ≤ V_DD − |V_GS2 − V_TH2|, i.e., node X must sit at least one overdrive voltage below V_DD).\n\n**Bring in M1.** Node X is the source of M1, so\n\n$$V_X = V_{b1} + V_{SG1} = V_{b1}+|V_{GS1}|$$\n\n**Result.** Substituting:\n\n$$V_{b1}+|V_{GS1}| \\ \\le\\ V_{b2}+|V_{TH2}|\n\\qquad\\Longrightarrow\\qquad\nV_{b1}\\ \\le\\ V_{b2}+|V_{TH2}|-|V_{GS1}|$$\n\nSo M2 is kept in saturation by choosing the cascode bias V_b1 low enough (relative to V_b2) that node X cannot rise above V_b2 + |V_TH2|. For maximum output swing, V_b1 is picked so that this holds with near‑equality (M2 at the edge of saturation, V_X ≈ V_DD − |V_OV2|); then, with M1 also saturated (V_out ≤ V_b1 + |V_TH1|), the output can swing up to about V_DD − |V_OV1| − |V_OV2|.",
        "format": "markdown",
        "sha256": "fdff435fe081b664ae11858b190ea8e4ae8c67e9eee32d508d9870f2cd4b33d5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, gives M2’s saturation condition, relates VX to Vb1, and derives the corresponding Vb1 bound. The essential reasoning matches the full-credit rule.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3726,
        "total_tokens": 6517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3029,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3726,
        "total_tokens": 6517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3029,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the condition**\n\nFor a PMOS device to be in saturation its drain can rise above its gate by at most one threshold:\n\n$$V_{SD} \\ge V_{SG} - |V_{TH}| \\quad\\Longleftrightarrow\\quad V_D \\le V_G + |V_{TH}|$$\n\nFor M₂ the source is at $V_{DD}$, the gate is at $V_{b2}$, and the drain is node X, so M₂ is saturated if\n\n$$V_X \\le V_{b2} + |V_{TH2}| \\qquad (\\text{equivalently } V_{SD2} \\ge V_{SG2}-|V_{TH2}| = |V_{OV2}|,\\ \\text{i.e. } V_X \\le V_{DD}-|V_{OV2}|)$$\n\n**What sets V_X?**\n\nNode X is the source of M₁, and M₁ carries the current that M₂ forces. Its gate‑source voltage is therefore fixed by that current, and\n\n$$V_X = V_{b1} + |V_{GS1}| = V_{b1} + |V_{TH1}| + |V_{OV1}|$$\n\n**Resulting design condition**\n\nSubstituting:\n\n$$V_{b1} + |V_{GS1}| \\le V_{b2} + |V_{TH2}|\n\\quad\\Longrightarrow\\quad\nV_{b1} \\le V_{b2} + |V_{TH2}| - |V_{GS1}|$$\n\nSo M₂ is kept in saturation by choosing the cascode bias $V_{b1}$ **low enough** (relative to $V_{b2}$) that node X does not rise above $V_{b2}+|V_{TH2}|$. $V_{b2}$ is set first (it determines the current, $V_{SG2}=V_{DD}-V_{b2}$), then $V_{b1}$ is generated by the bias network to satisfy the inequality above.\n\n**Practical note:** you don't want $V_{b1}$ *too* low, because M₁ itself stays saturated only for $V_{out} \\le V_{b1}+|V_{TH1}|$, so an unnecessarily low $V_{b1}$ wastes output swing. The optimum is to bias M₂ right at the edge, $V_X = V_{DD}-|V_{OV2}|$, i.e. $V_{b1} = V_{DD}-|V_{OV2}|-|V_{GS1}|$, which gives the maximum output voltage $V_{out,max} = V_{DD}-|V_{OV1}|-|V_{OV2}|$.",
        "format": "markdown",
        "sha256": "8e6f181ba6a00759d502c32425e8c771c9da0d0d7ff94486741b1c5b9d6d1743"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, gives M2’s saturation condition, and uses V_X = V_b1 + |V_GS1| to derive the required condition on V_b1, matching the full-credit rule.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3591,
        "total_tokens": 6382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2739,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2791,
        "output_tokens": 3591,
        "total_tokens": 6382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2739,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nThis is an **NMOS cascode amplifier** (a \"telescopic\" cascode stage):\n\n| Device | Role |\n|---|---|\n| M1 | Common‑source input transistor (converts v_in to a drain current) |\n| M2 | Common‑gate \"cascode\" transistor, gate held at the DC bias V_b1 |\n| I1 | Ideal current‑source load (infinite small‑signal impedance) |\n| X | Internal node: drain of M1 / source of M2 |\n| v_out | Drain of M2 |\n\nM1 and M2 are in series, so both carry the same bias current I1.\n\n---\n\n## 2. DC operating point and headroom\n\n- **Currents:** I_D1 = I_D2 = I1.\n- **Input bias:** V_in(DC) must equal the V_GS1 that supports I1:\n V_GS1 = V_TH1 + √(2I1 / μnCox(W/L)1) = V_TH1 + V_ov1\n- **Node X:** V_X = V_b1 − V_GS2, with V_GS2 = V_TH2 + V_ov2.\n- **M1 in saturation:** V_X ≥ V_in − V_TH1 = V_ov1 ⟹ **V_b1 ≥ V_GS2 + V_ov1**.\n- **M2 in saturation:** V_out ≥ V_b1 − V_TH2.\n\nIf V_b1 is chosen at its minimum value (V_GS2 + V_ov1):\n\n  **V_out,min = V_ov1 + V_ov2**\n\nSo the output can swing from roughly V_DD (minus whatever the real current source needs) down to V_ov1 + V_ov2. Compared with a simple CS stage, the cascode costs **one extra overdrive voltage** of headroom. (Note: with a truly ideal I1 the DC output level is not self‑defined—any mismatch between I1 and I_D1 drives v_out to a rail—so in practice the operating point is set by feedback or a realistic load.)\n\n---\n\n## 3. Small‑signal analysis\n\n### Output resistance\nLooking into the drain of M2, M2 is a CG device degenerated by r_O1 (M1 with grounded gate is just r_O1):\n\n **R_out = r_O2 + r_O1 + (g_m2 + g_mb2) r_O1 r_O2 = [1 + (g_m2+g_mb2) r_O2] r_O1 + r_O2 ≈ g_m2 r_O2 · r_O1**\n\nThe output resistance of M1 alone (r_O1) is boosted by the factor g_m2 r_O2.\n\n### Transconductance\nWith the output ac‑grounded, the resistance looking into the source of M2 is ≈ 1/(g_m2+g_mb2) ≪ r_O1, so essentially all of g_m1·v_in flows through M2:\n\n **G_m ≈ g_m1**\n\n### Voltage gain\n **A_v = −G_m R_out ≈ −g_m1 [ (1 + (g_m2+g_mb2) r_O2) r_O1 + r_O2 ] ≈ −(g_m1 r_O1)(g_m2 r_O2)**\n\n(Exact result for the ideal load: since no signal current can flow into I1, i_D2 = 0, giving v_X = −g_m1 r_O1 v_in and v_out = v_X[1 + (g_m2+g_mb2) r_O2], i.e. A_v = −g_m1 r_O1[1 + (g_m2+g_mb2) r_O2].)\n\nThe gain is roughly the **product of the two intrinsic gains** (g_m r_O)², versus just g_m1 r_O1 for a plain CS stage. With a practical PMOS (cascode) current source of output resistance R_p, A_v ≈ −g_m1 (R_out ‖ R_p).\n\n### Node X and \"shielding\"\n- From output to X: v_X / v_out = 1 / [1 + (g_m2+g_mb2) r_O2] ≈ 1/(g_m2 r_O2) — M2 shields the drain of M1 from output swings, which is exactly why R_out is so high.\n- With a finite load R_L, the gain from v_in to node X is only ≈ −g_m1 (R_L + r_O2)/(g_m2 r_O2) (≈ −1 for R_L ~ r_O), so Miller multiplication of C_GD1 is small.\n\n### Input resistance\nInfinite (gate of M1).\n\n---\n\n## 4. Summary of properties\n\n**Advantages**\n- Output resistance and voltage gain multiplied by ≈ g_m2 r_O2 (e.g., with g_m r_O = 20 each: gain ≈ 400 vs. 20 for a CS stage).\n- Reduced Miller effect → wider bandwidth; good reverse isolation (output → input).\n- Better immunity of the bias current to output‑voltage variations.\n\n**Costs**\n- One extra V_ov of voltage headroom (V_out,min = V_ov1 + V_ov2).\n- Requires a bias voltage V_b1 (and body effect raises V_TH2, pushing V_b1 higher).\n- Adds a (usually high‑frequency) pole at node X, ≈ g_m2/C_X.",
        "format": "markdown",
        "sha256": "850c7d3b2591ce7f77b6fc35dba3a2f76273035183ebb229c7ecb8a9da761dec"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression specified by the full-credit rule. Minor claims about secondary behavior do not undermine the essential analysis.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 6979,
        "total_tokens": 8433,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5214,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 6979,
        "total_tokens": 8433,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5214,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Circuit identification\n\nThis is an **NMOS cascode amplifier** (a common‑source stage stacked under a common‑gate stage) loaded by an ideal current source:\n\n- **M₁** – input device, common‑source: converts v_in into a drain current (transconductance g_m1).\n- **M₂** – cascode device, common‑gate: gate held at the fixed bias V_b1, source at node X, drain at the output. It passes M₁'s current to the output while raising the output impedance.\n- **I₁** – ideal current‑source load (infinite small‑signal resistance), so the gain is set entirely by the cascode's own output resistance.\n\n---\n\n## 1. DC (bias) analysis\n\n- Both transistors carry the same current: I_D1 = I_D2 = I₁.\n- Node X sits at V_X = V_b1 − V_GS2 (its value is set by V_b1, not by V_in).\n- Saturation conditions:\n  - M₁: V_X ≥ V_GS1 − V_TH1 ⇒ **V_b1 ≥ V_GS2 + (V_GS1 − V_TH1)**\n  - M₂: V_out ≥ V_b1 − V_TH2\n- If V_b1 is set at its minimum, the output can swing down to\n\n  V_out,min = (V_GS1 − V_TH1) + (V_GS2 − V_TH2) = two overdrive voltages,\n\n  i.e., the cascode costs one extra overdrive of headroom compared with a simple CS stage. (With an ideal I₁ the output may rise to V_DD; a real current source would subtract one more overdrive.)\n\n---\n\n## 2. Small‑signal analysis\n\n### Output resistance\nLooking into the drain of M₂, r_O1 acts as a degeneration resistor in M₂'s source:\n\nR_out = (1 + g_m2 r_O2) r_O1 + r_O2 ≈ **g_m2 r_O2 r_O1**\n\nM₂ \"boosts\" r_O1 by its intrinsic gain g_m2 r_O2.\n\n### Transconductance\nWith the output shorted, the impedance seen at the source of M₂ is ≈ 1/g_m2 ≪ r_O1, so essentially all of M₁'s current g_m1 v_in flows through M₂:\n\nG_m ≈ g_m1\n\n### Voltage gain\nA_v = −G_m R_out ≈ −g_m1[(1 + g_m2 r_O2) r_O1 + r_O2] ≈ **−g_m1 g_m2 r_O1 r_O2**\n\nDirect nodal check (no small‑signal current can flow in the ideal source I₁, so i_d1 = i_d2 = 0):\n\n- M₁: g_m1 v_in + v_X / r_O1 = 0 ⇒ v_X = −g_m1 r_O1 v_in\n- M₂: −g_m2 v_X + (v_out − v_X)/r_O2 = 0 ⇒ v_out = (1 + g_m2 r_O2) v_X\n\n⇒ v_out / v_in = −g_m1 r_O1 (1 + g_m2 r_O2) ≈ −(g_m r_O)² for identical devices.\n\n(Including body effect of M₂, replace g_m2 by g_m2 + g_mb2 — it slightly *increases* the gain and R_out.)\n\n---\n\n## 3. Interpretation\n\n- **Why the gain is so high:** a simple CS stage with the same ideal load gives only −g_m1 r_O1. The cascode multiplies this by another intrinsic gain (1 + g_m2 r_O2), giving roughly the square of a single transistor's intrinsic gain. E.g., with g_m r_O = 50 per device, |A_v| ≈ 2500 instead of 50.\n- **Shielding property:** the gain from v_out back to node X is only ≈ 1/(g_m2 r_O2), so output swings barely disturb V_DS1; M₁'s current stays nearly constant → very high R_out.\n- **Bandwidth advantage (in a practical loaded case):** the low impedance at X reduces the Miller multiplication of C_GD1, giving better high‑frequency behavior than a CS stage of comparable gain.\n- **Costs:** reduced voltage headroom (extra overdrive) and the need for the bias voltage V_b1; with an ideal current source the input DC level must be exactly matched to I₁ (in practice the PMOS load's finite r_O or a feedback loop defines the operating point).\n\n**Summary:** the circuit is a telescopic NMOS cascode amplifier with R_out ≈ g_m2 r_O2 r_O1 and voltage gain A_v ≈ −g_m1 g_m2 r_O1 r_O2, obtained at the expense of about one overdrive voltage of output swing.",
        "format": "markdown",
        "sha256": "2466f53ac6e436a1f12f0bd2beccf5f52d460003101a24efef0eda12355580d5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression. The golden solution’s full-credit rule applies; body effect is also acknowledged.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 5963,
        "total_tokens": 7417,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 5963,
        "total_tokens": 7417,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\nThis is an **NMOS cascode amplifier** (a \"telescopic\" cascode stage) with an ideal current‑source load:\n\n| Device | Role |\n|---|---|\n| M1 (gate = v_in, source = ground) | Common‑source input device – converts v_in to a current |\n| M2 (gate = V_b1, source = node X) | Common‑gate \"cascode\" device – passes M1's current to the output and raises the output impedance |\n| I1 | Ideal current source load (infinite small‑signal impedance) |\n| Node X | Internal node between the two transistors |\n\nBoth transistors carry the same bias current: I_D1 = I_D2 = I1.\n\n## 2. DC operation / headroom\n\n- V_X = V_b1 − V_GS2\n- M1 saturated ⇒ V_X ≥ V_GS1 − V_TH1 = V_ov1 ⇒ **V_b1 ≥ V_GS2 + V_ov1** \n- M2 saturated ⇒ V_out ≥ V_b1 − V_TH2 ⇒ with V_b1 at its minimum, **V_out,min = V_ov1 + V_ov2**\n\nSo V_b1 should be chosen just large enough to keep M1 in saturation; every extra volt in V_b1 is lost output swing. The cascode costs one additional overdrive voltage of headroom compared with a simple CS stage; the upper limit of V_out is set by the compliance of I1 (ideally up to V_DD).\n\n(Note: λ must be nonzero in the analysis; with λ = 0 and an ideal current source, the gain would be infinite.)\n\n## 3. Small‑signal analysis\n\nReplace I1 by an open circuit, and use the models of M1 (g_m1, r_O1) and M2 (g_m2, r_O2, v_gs2 = −v_X).\n\n**KCL at the output node** – no AC current can flow into the ideal source, so i_d2 = 0:\n\n−g_m2·v_X + (v_out − v_X)/r_O2 = 0  ⇒ v_out = (1 + g_m2 r_O2)·v_X\n\n**KCL at node X** – M2's source current equals its drain current, which is zero, so i_d1 = 0:\n\ng_m1·v_in + v_X / r_O1 = 0  ⇒ v_X = −g_m1 r_O1 · v_in\n\n**Voltage gain:**\n\n$$A_v=\\frac{v_{out}}{v_{in}}=-g_{m1}r_{O1}\\,(1+g_{m2}r_{O2})\\;\\approx\\;-\\,g_{m1}g_{m2}\\,r_{O1}r_{O2}$$\n\ni.e. the gain is the **product of the two intrinsic gains**, (g_m1 r_O1)(g_m2 r_O2). Including the body effect of M2 (its source is not grounded), replace g_m2 by (g_m2 + g_mb2).\n\n**Output resistance** (looking into the drain of M2, v_in = 0):\n\n$$R_{out}=(1+g_{m2}r_{O2})\\,r_{O1}+r_{O2}\\;\\approx\\;g_{m2}r_{O2}\\,r_{O1}$$\n\nM2 multiplies r_O1 by its own intrinsic gain, g_m2 r_O2.\n\n**Effective transconductance:**\n\n$$G_m=\\frac{-A_v}{R_{out}}=\\frac{g_{m1}(1+g_{m2}r_{O2})r_{O1}}{(1+g_{m2}r_{O2})r_{O1}+r_{O2}}\\approx g_{m1}$$\n\nso the familiar form A_v = −G_m R_out ≈ −g_m1 R_out holds.\n\n**Input resistance:** infinite at low frequency (MOS gate).\n\n## 4. Interpretation\n\n- **Why the gain is high:** a simple CS stage with an ideal current load gives only −g_m1 r_O1. Stacking M2 raises the output impedance by ≈ g_m2 r_O2 (typically 20–50×), and the gain rises by the same factor.\n- **Shielding:** M2 isolates node X from the output: ΔV_X/ΔV_out ≈ 1/(g_m2 r_O2). The drain voltage of M1 therefore barely moves, its current is almost independent of v_out, which is exactly why R_out is so large (also improves linearity).\n- **Node X with this ideal load:** the resistance seen looking into M2's source is (r_O2 + R_L)/(1 + g_m2 r_O2). With R_L → ∞ this is very large, which is why the gain to node X is the full −g_m1 r_O1 here. With a realistic finite load, node X becomes a low‑impedance node (≈ 1/g_m2 + R_L/(g_m2 r_O2)), which is what reduces the Miller multiplication of C_GD1 and gives the cascode its bandwidth advantage.\n- **Practical caveat:** if I1 is implemented with a single PMOS transistor (R_L = r_O3), the gain becomes ≈ −g_m1 (R_out ‖ r_O3) ≈ −g_m1 r_O3 — the cascoding of the NMOS side is wasted. To actually realize the g_m r_O² gain, the load current source must also be cascoded.",
        "format": "markdown",
        "sha256": "2d7070813285610b51634d7012d979080bdceba797195ef11e0ec005efc9e95e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and derives the valid ideal-load gain expression. The additional body-effect note and output-resistance discussion are consistent with the circuit.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 7534,
        "total_tokens": 8988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5741,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1454,
        "output_tokens": 7534,
        "total_tokens": 8988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5741,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.** It only *looks* like a cascode because two transistors are stacked under R_D. Look at the device symbols:\n\n- **M2** is an NMOS: its arrow (lower terminal) points *away* from the channel, so the lower terminal is its source, gate at V_b1 → a common‑gate device. ✔\n- **M1** is a **PMOS**: its arrow (upper terminal) points *into* the channel, so the *upper* terminal is M1's source and its drain is the grounded terminal.\n\nHence the node between the two transistors is the **source of M1 tied to the source of M2**, and M1's drain is at (ac) ground.\n\nIn a true cascode the input device is a common‑source stage: V_in drives its gate and its *drain* current is fed into the source of the common‑gate device. Here M1 has gate input, source output and drain grounded – i.e. it is a **source follower (common‑drain)**, not a common‑source stage. The circuit is therefore a *source follower driving a common‑gate stage*, not a cascode.\n\nThe behavior is correspondingly different:\n\n- Gain (ignoring r_O): the follower sees a load of 1/g_m2, so  \n v_out/v_in ≈ [g_m1/(g_m1+g_m2)]·(g_m2 R_D) = R_D /(1/g_m1 + 1/g_m2), **non‑inverting**, instead of the cascode's ≈ −g_m1 R_D.\n- Output impedance: the source of M2 sees only 1/g_m1 ∥ r_O1, so  \n R_out ≈ r_O2 + (1+g_m2 r_O2)(1/g_m1 ∥ r_O1) ≈ r_O2(1+g_m2/g_m1), **not** the boosted g_m2 r_O2 r_O1 of a cascode.\n\n(The circuit can still be biased – current flows V_DD → R_D → M2 (D→S) → M1 (S→D) → ground, provided V_b1 − V_X > V_THN and V_X − V_in > |V_THP| – but it is not a cascode structure.)",
        "format": "markdown",
        "sha256": "e407a190eb242083f33718ca22ce8052b1195dfa550fd692845594eb4fe7a609"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS source follower with its drain grounded and M2 as common-gate, so the circuit is not a cascode and lacks cascode resistance boosting. The stated output-resistance expression is consistent with the golden solution.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 7481,
        "total_tokens": 9007,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6784,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 7481,
        "total_tokens": 9007,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6784,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No, it is not a cascode.**\n\nLook at the source arrows on the two devices:\n\n- **M2** has its arrow on the bottom terminal pointing *out* of the device → M2 is an **NMOS** with its source at the middle node.\n- **M1** has its arrow on the top terminal pointing *into* the device → M1 is a **PMOS** whose **source** is at the middle node and whose **drain** is grounded.\n\nSo the two transistors are joined **source‑to‑source**, not drain‑to‑source.\n\n**Why that matters**\n\nA cascode consists of a common‑source input device (voltage‑to‑current converter) whose *drain* current is passed through a common‑gate device. The CG device sees a high‑impedance (current‑source‑like) node at the drain of the input device, which is what gives the cascode its large output resistance (≈ gₘ₂r_O₂·r_O₁) and its \"shielding\" property.\n\nHere, M1 receives V_in at its gate, has its drain at (ac) ground, and delivers its output at its *source*. That is a **source follower** (common‑drain stage), not a common‑source stage. M2, with its gate at a fixed bias V_b1, is a common‑gate stage. The circuit is therefore a **CD–CG cascade**, not a CS–CG cascode:\n\n- Node X (the common sources) is a low‑impedance node (≈1/gₘ₁ ‖ 1/gₘ₂).\n- Neglecting λ and body effect: V_X ≈ V_in·gₘ₁/(gₘ₁+gₘ₂), so \n  A_v = V_out/V_in ≈ +gₘ₂R_D·gₘ₁/(gₘ₁+gₘ₂) — a *non‑inverting* gain smaller than gₘ₂R_D (gₘR_D/2 if gₘ₁ = gₘ₂), unlike a cascode's ≈ –gₘ₁R_D.\n- The resistance seen looking into the drain of M2 is only r_O₂[1 + gₘ₂(1/gₘ₁‖r_O₁)] ≈ r_O₂(1 + gₘ₂/gₘ₁), i.e., about 2r_O₂, not the gₘ₂r_O₂r_O₁ of a true cascode. No impedance boosting occurs.\n\nIt would be a cascode only if M1 were an NMOS with its source grounded and its *drain* driving the source of M2 (or, in the folded‑cascode form, a PMOS with source at V_DD and drain feeding the source of M2 together with a bias current source).",
        "format": "markdown",
        "sha256": "c5f7ca4b6a8c012c537ad62d0ac9b4dbb41ea82a8df09bbaf52ce56a76ad0717"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS source follower rather than a common-source input device, so the circuit is not a cascode and lacks cascode output-resistance boosting. The extra analysis is consistent with the essential conclusion.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 10844,
        "total_tokens": 12370,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9982,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 10844,
        "total_tokens": 12370,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9982,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.** At first glance it looks like the standard NMOS cascode (input device on the bottom, bias‑gated device M₂ on top, resistive load R_D), but look at the arrows on the transistor symbols:\n\n- **M₂**: the arrow is on its *bottom* terminal and points *out* of the device → NMOS, source at the bottom (node X), drain at V_out. ✔ (common‑gate device)\n- **M₁**: the arrow is on its *top* terminal and points *into* the device → **M₁ is a PMOS**, with its *source* at node X and its *drain* grounded.\n\nSo the middle node X is a **source‑to‑source** connection, not the drain‑to‑source connection a cascode requires. A cascode is a common‑source (input) stage whose drain drives the source of a common‑gate stage. Here, M₁ has its input at the gate and its output at its source, i.e., it works as a **source follower (common‑drain)** that drives the common‑gate stage M₂. The circuit is a CD–CG cascade, not a cascode.\n\nIt also lacks the cascode's defining property – the large output resistance. The resistance seen at node X looking into M₁ is only ≈1/g_m1 (a follower's output resistance), not r_o1, so\n\nR_out ≈ r_o2 + (1 + g_m2 r_o2)/g_m1 ≈ r_o2(1 + g_m2/g_m1),\n\nrather than the ≈ g_m2 r_o2 r_o1 of a true cascode. (The gain is also small and positive, roughly g_m2R_D·g_m1/(g_m1+g_m2), instead of the inverting –g_m1R_D of a cascode.)\n\nIf M₁ were an NMOS with its source grounded and its drain tied to the source of M₂, the circuit would indeed be a cascode.",
        "format": "markdown",
        "sha256": "2a7fc05351743ffd8aabfbdf447cfd7c3def3f522ff927fd2045d72dde54f068"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a PMOS source follower with its drain grounded, so the circuit is not a cascode and lacks cascode output-resistance boosting. The output-resistance approximation is consistent with the stated assumptions.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 5316,
        "total_tokens": 6842,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4709,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1526,
        "output_tokens": 5316,
        "total_tokens": 6842,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4709,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Short version\n\nThe Miller effect multiplies a feedback capacitance by the voltage gain across it. In a cascode, the input transistor is forced to have a voltage gain of only about −1, so its base–collector (gate–drain) capacitance is multiplied by only ~2 instead of by the full stage gain. The large voltage swing is produced instead by a common-base/common-gate transistor whose feedback capacitance is not multiplied at all.\n\n## Why it happens\n\n**1. Where the Miller effect comes from**\n\nFor an inverting stage with gain −A, a capacitor C bridging input and output has a voltage change across it of ΔV_in(1 + A) when the input changes by ΔV_in. The source must supply (1 + A) times more charge than it would for a grounded capacitor, so the input sees\n\nC_in,eff = C(1 + A).\n\nIn a single common-emitter (common-source) stage, C_μ (C_gd) is exactly such a bridging capacitor, and A ≈ g_m R_L can be large (tens to hundreds). Together with the source resistance R_S this creates a low-frequency input pole, f_p ≈ 1/[2πR_S(C_π + C_μ(1 + g_m R_L))], which usually dominates the bandwidth.\n\n**2. What the cascode changes**\n\nIn a cascode, the input transistor Q1 (CE/CS) does not drive R_L directly. Its collector drives the emitter of Q2, which is a common-base (common-gate) stage. The impedance looking into an emitter is very low, roughly 1/g_m2.\n\nSo the voltage gain of Q1 becomes\n\nA_1 ≈ −g_m1 · (1/g_m2) ≈ −1 (both transistors carry the same bias current)\n\nand its Miller-multiplied capacitance is only\n\nC_in ≈ C_π1 + C_μ1(1 + 1) = C_π1 + 2C_μ1.\n\nThe multiplication factor dropped from (1 + g_m R_L) to about 2.\n\n**3. The gain isn't lost — it's just moved somewhere Miller can't act**\n\nQ2 is a current buffer: the signal current g_m1·v_in flows through it essentially unchanged (α ≈ 1) into R_L, so the overall gain is still ≈ −g_m1 R_L. The large voltage swing now appears at Q2's collector, but:\n\n- Q2's base (gate) is at AC ground, so its C_μ2 (C_gd2) is simply a shunt capacitance from the output node to ground — nothing to multiply.\n- Q2 is non-inverting from emitter to collector and has no significant direct emitter–collector capacitance, so there is no feedback path from its high-swing output back to its input.\n\n**4. Net result**\n\n- The input pole moves up to roughly 1/[2πR_S(C_π1 + 2C_μ1)] — a large bandwidth improvement when R_S is significant.\n- The intermediate node (Q1 collector / Q2 emitter) has low impedance (~1/g_m2) and small capacitance (C_μ1 + C_π2), so its pole is at a very high frequency.\n- The output pole is set by R_L and (C_μ2 + C_L), as before.\n\nThe same mechanism also gives the cascode its excellent reverse isolation: there is no longer a single capacitor connecting a high-swing output node directly to the input.\n\n*(Caveat: if the cascode is loaded with a very high impedance, e.g. a cascode current source, the impedance looking into Q2's emitter rises to ≈ (r_o2 + R_L)/(g_m2 r_o2), Q1's gain grows beyond −1, and some Miller multiplication returns — but it remains far smaller than in a single stage with the same total gain.)*",
        "format": "markdown",
        "sha256": "652815b1ed105c6ffaaf469a6e273408fff41dc2141ef840e6a151a2301e8370"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance cascode node and the resulting local gain of about −1, so M1’s gate-drain capacitance is multiplied by about 2 rather than by the full stage gain. The additional discussion is consistent with the main explanation.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2805,
        "total_tokens": 2835,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1562,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2805,
        "total_tokens": 2835,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1562,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## The Miller effect in a plain common-emitter / common-source stage\n\nA capacitor connected between the input and output of an inverting amplifier with voltage gain \\(A_v\\) looks, from the input, like a capacitor of value\n\n\\[\nC_{\\text{in,Miller}} = C\\,(1 - A_v) = C\\,(1 + |A_v|).\n\\]\n\nIn a CE (or CS) stage, the collector–base capacitance \\(C_\\mu\\) (or \\(C_{gd}\\)) sits exactly in that position: between the base (input) and the collector (output). Because the stage gain is large, \\(A_v \\approx -g_m R_L\\), the small \\(C_\\mu\\) is multiplied by a big factor:\n\n\\[\nC_{\\text{in}} \\approx C_\\pi + C_\\mu\\,(1 + g_m R_L).\n\\]\n\nThis large input capacitance, together with the source resistance \\(R_s\\), creates a low‑frequency pole, \\(f_p \\approx 1/(2\\pi R_s C_{\\text{in}})\\), that usually dominates and limits the bandwidth.\n\n## What the cascode changes\n\nA cascode is a CE (CS) transistor \\(Q_1\\) whose collector feeds the emitter of a common‑base (common‑gate) transistor \\(Q_2\\), with the output taken at \\(Q_2\\)'s collector and \\(Q_2\\)'s base held at AC ground.\n\n**1. The first transistor no longer has voltage gain.**\nThe load seen by \\(Q_1\\)'s collector is the input resistance of the common‑base stage, which is very low, roughly \\(1/g_{m2}\\). So the voltage gain from \\(Q_1\\)'s base to its collector is\n\n\\[\nA_{v1} \\approx -g_{m1}\\cdot\\frac{1}{g_{m2}} \\approx -1\n\\]\n\n(the two devices carry the same current, so \\(g_{m1}\\approx g_{m2}\\)). The Miller multiplication factor for \\(C_{\\mu1}\\) therefore drops from \\(1 + g_m R_L\\) to about \\(1 + 1 = 2\\):\n\n\\[\nC_{\\text{in}} \\approx C_\\pi + 2C_\\mu \\quad\\text{instead of}\\quad C_\\pi + (1 + g_m R_L)C_\\mu .\n\\]\n\nEven though \\(Q_1\\) has almost no *voltage* gain, it still converts the input voltage to a signal current \\(g_{m1}v_{in}\\). That current passes through \\(Q_2\\) (whose current gain is \\(\\alpha \\approx 1\\)) into \\(R_L\\), so the overall gain is still \\(\\approx -g_{m1}R_L\\). The gain is preserved; only the voltage swing at the sensitive internal node is suppressed.\n\n**2. The second transistor has no Miller path at all.**\nIn \\(Q_2\\), the base is at AC ground, so \\(C_{\\mu2}\\) connects the output node to ground, not to the stage's input (the emitter). It is a plain shunt capacitance on the output — no feedback, no multiplication. Likewise \\(C_{\\pi2}\\) is just from the emitter to ground. The common‑base stage is intrinsically free of Miller feedback and is broadband (its current gain stays near unity up to about \\(f_T\\)).\n\n**3. The internal node is fast.**\nThe node between \\(Q_1\\) and \\(Q_2\\) has low impedance (\\(\\approx 1/g_{m2}\\)), so the pole formed there is at a high frequency (\\(\\sim g_{m2}/C_{\\text{node}}\\)) and rarely limits bandwidth.\n\n## Numerical illustration\n\nTake \\(g_m = 40\\ \\text{mS}\\), \\(R_L = 5\\ \\text{k}\\Omega\\) (gain ≈ 200), \\(C_\\pi = 10\\ \\text{pF}\\), \\(C_\\mu = 1\\ \\text{pF}\\), \\(R_s = 1\\ \\text{k}\\Omega\\):\n\n- CE: \\(C_{\\text{in}} \\approx 10 + 1\\times201 = 211\\ \\text{pF}\\) → input pole ≈ 0.75 MHz\n- Cascode: \\(C_{\\text{in}} \\approx 10 + 2 = 12\\ \\text{pF}\\) → input pole ≈ 13 MHz\n\nSame gain, roughly an order of magnitude more bandwidth from the input pole alone (the output pole \\(1/(2\\pi R_L(C_{\\mu2}+C_L))\\) then typically becomes the limiter).\n\n## Summary\n\nThe Miller effect is small in a cascode because the capacitance that would be multiplied, \\(C_{\\mu1}\\), sees a voltage gain of only about −1 across it (the common‑base transistor presents a \\(1/g_m\\) load), while the transistor that *does* produce the large output voltage swing has its base grounded, so its feedback capacitance is simply a capacitor to ground. The cascode thus separates the \"transconductance\" job from the \"voltage swing\" job, and the high gain is achieved as a current gain into the load rather than as a voltage swing across a feedback capacitance. The cost is one extra transistor's worth of voltage headroom.",
        "format": "markdown",
        "sha256": "6fd5cb2d939b394279bf0c9921c016a3b99305afb0f7feb79fd3feff73c54e00"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance cascode node and the resulting gain of about −1 across the input transistor’s feedback capacitance, giving a Miller factor of about 2 rather than the full stage gain. The remaining details are consistent with the essential explanation.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 3882,
        "total_tokens": 3912,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2161,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 3882,
        "total_tokens": 3912,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2161,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## The Miller effect in a single common-emitter (common-source) stage\n\nIn a CE/CS amplifier, the collector–base capacitance **C<sub>μ</sub>** (or **C<sub>gd</sub>** in a MOSFET) bridges the input node (base) and the output node (collector). Because the stage has a large *inverting* voltage gain,\n\nA<sub>v</sub> ≈ −g<sub>m</sub>R<sub>L</sub>,\n\nany voltage change ΔV at the base produces a change −|A<sub>v</sub>|ΔV at the collector, so the voltage across C<sub>μ</sub> is (1 + |A<sub>v</sub>|)ΔV. The input source therefore has to supply (1 + |A<sub>v</sub>|) times the charge, and C<sub>μ</sub> appears at the input as\n\nC<sub>in</sub> = C<sub>π</sub> + C<sub>μ</sub>(1 + g<sub>m</sub>R<sub>L</sub>).\n\nWith g<sub>m</sub>R<sub>L</sub> ≈ 100, a 1 pF C<sub>μ</sub> looks like ~100 pF. Together with the source resistance R<sub>S</sub>, this creates a low-frequency input pole that dominates and limits the bandwidth.\n\n## What the cascode changes\n\nA cascode stacks a common-base (common-gate) transistor Q2 on top of the CE/CS transistor Q1. The crucial fact is the **input impedance of the common-base stage**, looking into Q2's emitter, is very low:\n\nR<sub>in,CB</sub> ≈ 1/g<sub>m2</sub> (≈ r<sub>e2</sub>).\n\nThat low impedance is the load seen by Q1's collector. So the voltage gain *of Q1 alone* is\n\nA<sub>v1</sub> ≈ −g<sub>m1</sub> · (1/g<sub>m2</sub>) ≈ −1 (same bias current ⇒ g<sub>m1</sub> ≈ g<sub>m2</sub>).\n\nThe Miller multiplication factor for C<sub>μ1</sub> collapses from (1 + g<sub>m</sub>R<sub>L</sub>) to about (1 + 1) = 2:\n\nC<sub>in</sub> ≈ C<sub>π1</sub> + 2C<sub>μ1</sub>.\n\nUsing the earlier numbers (C<sub>π</sub> = 10 pF, C<sub>μ</sub> = 1 pF, R<sub>S</sub> = 1 kΩ): the CE stage has C<sub>in</sub> ≈ 111 pF → f<sub>pole</sub> ≈ 1.4 MHz, while the cascode has C<sub>in</sub> ≈ 12 pF → f<sub>pole</sub> ≈ 13 MHz. Nearly an order of magnitude more bandwidth.\n\n## Why the overall gain is not lost\n\nQ1 still converts the input voltage into a signal current g<sub>m1</sub>v<sub>in</sub>. The common-base stage has a current gain of essentially unity (α ≈ 1), so it passes that current straight through to the real load R<sub>L</sub> at Q2's collector. The total gain is still\n\nA<sub>v</sub> ≈ −g<sub>m1</sub>R<sub>L</sub>,\n\ni.e., the same as the plain CE stage. The large voltage swing is simply moved to a node (Q2's collector) that has **no capacitive path back to the input**.\n\n## The intuitive picture\n\n- Q2's base is at AC ground, so Q2's emitter (and hence Q1's collector) is held at a nearly constant voltage — it \"follows\" the fixed base. The signal swing across C<sub>μ1</sub> is therefore tiny, and little charge has to flow through it from the input. The output voltage swing is isolated from the input.\n- The common-base transistor itself has no Miller problem: its C<sub>μ2</sub> goes from collector to the AC-grounded base, so it just adds to the output node capacitance with no gain multiplication. Its C<sub>π2</sub> sits at a low-impedance node (1/g<sub>m2</sub>), giving a pole at very high frequency.\n\n## Summary\n\nThe Miller effect is small in a cascode because the first transistor drives a very low impedance (≈1/g<sub>m</sub>) rather than the full load resistance, so its local voltage gain is only about −1. The feedback capacitance is therefore multiplied by ~2 instead of ~(1 + g<sub>m</sub>R<sub>L</sub>), while the common-base stage delivers the same signal current to the load, preserving the overall gain and greatly extending the bandwidth (at the cost of extra voltage headroom for the stacked transistor).",
        "format": "markdown",
        "sha256": "de226bdbd3793d4f762282ff6c1ca4923e4aad7fd3257e3643c7603dea82d9f4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The main explanation is correct: the common-gate device presents a low impedance at Q1’s drain, giving Q1 a gain near −1 and a Miller factor near 2. But the answer later incorrectly calls the swing across Cμ1 tiny and the drain nearly fixed; the capacitor voltage is about twice the input swing, as the answer’s own factor-of-2 calculation shows.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 3175,
        "total_tokens": 3205,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1549,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 3175,
        "total_tokens": 3205,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1549,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**1. Identifying the topology**\n\n- **M1** is a PMOS (arrow on the source pointing into the device) with its source at V_DD and its gate at the fixed voltage V_b2. Both terminals are at ac ground, so M1 is a **current‑source (active) load** that presents only its output resistance r_O1 to the output node.\n- **M2** is an NMOS (arrow pointing out of the source) drawn upside‑down: gate at the constant V_b1, **source driven by V_in**, drain tied to V_out.\n\nInput at the source, output at the drain, gate at ac ground → this is a **common‑gate (CG) stage with a current‑source load**.\n\n**2. Bias (dc) conditions**\n\nThe bias current I_D flows from V_DD through M1 and M2 and into the input source (V_in must sink it):\n\nI_D = ½μ_nC_ox(W/L)₂ (V_b1 − V_IN − V_TH2)² = ½μ_pC_ox(W/L)₁ (V_DD − V_b2 − |V_TH1|)²\n\n- M2 on: V_IN < V_b1 − V_TH2\n- M2 saturated: V_DS2 ≥ V_GS2 − V_TH2 ⇒ V_out ≥ V_b1 − V_TH2\n- M1 saturated: V_SD1 ≥ V_SG1 − |V_TH1| ⇒ V_out ≤ V_b2 + |V_TH1|\n\nSo V_b1 − V_TH2 ≤ V_out ≤ V_b2 + |V_TH1| is the allowed output range. (As with any current‑source‑loaded stage, the two currents must be matched – in practice feedback is needed to pin V_out.)\n\n**3. Small‑signal gain**\n\nSmall‑signal model: gate of M2 at ground, so v_gs2 = v_bs2 = −v_in; M1 → r_O1 from v_out to ground.\n\nKCL at the output node:\n\nv_out/r_O1 + (v_out − v_in)/r_O2 − (g_m2 + g_mb2)v_in = 0\n\n$$\nA_v=\\frac{v_{out}}{v_{in}}=\\Big(g_{m2}+g_{mb2}+\\frac{1}{r_{O2}}\\Big)(r_{O1}\\parallel r_{O2})\n=\\big[1+(g_{m2}+g_{mb2})r_{O2}\\big]\\frac{r_{O1}}{r_{O1}+r_{O2}}\n$$\n\n- Neglecting body effect: A_v ≈ g_m2(r_O1 ∥ r_O2) (≈ g_m r_O/2 if r_O1 = r_O2).\n- λ₂ = 0 (keep only r_O1): A_v = (g_m2 + g_mb2) r_O1.\n- Ideal load (r_O1 → ∞): A_v → 1 + (g_m2 + g_mb2) r_O2 (the intrinsic gain limit).\n- If λ = 0 for both devices the gain is unbounded, so r_O must be kept.\n\nThe gain is **positive (non‑inverting)**, and body effect *increases* it because the source is the input terminal.\n\n**4. Input and output resistances**\n\nLooking into the source of M2 with r_O1 as drain load:\n\n$$\nR_{in}=\\frac{r_{O1}+r_{O2}}{1+(g_{m2}+g_{mb2})r_{O2}}\n\\;\\approx\\;\\frac{1}{g_{m2}+g_{mb2}}\\Big(1+\\frac{r_{O1}}{r_{O2}}\\Big)\n$$\n\ni.e., the active load raises R_in above the usual 1/(g_m+g_mb) (and R_in → ∞ for an ideal current source, since the signal current is then fixed by the load).\n\nLooking into the output (ideal voltage source at the input):\n\n$$\nR_{out}=r_{O1}\\parallel r_{O2}\n$$\n\n(with a source resistance R_S: R_out = r_O1 ∥ [r_O2 + (1 + (g_m2+g_mb2)r_O2)R_S]).\n\n**Summary:** a CG amplifier whose resistive load has been replaced by the PMOS current source M1, giving a high, non‑inverting voltage gain ≈ g_m2(r_O1∥r_O2), a low input resistance of order 1/g_m2, and an output resistance r_O1∥r_O2.",
        "format": "markdown",
        "sha256": "1c37a76819cd369213c1a90ff6c556facf8ff43b8a238a04a2d0fd1659afc618"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS with PMOS current-source load, places the input at M2’s source, identifies both bias voltages, and gives the non-inverting gain and low input resistance. The detailed formulas are consistent with the topology.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 10191,
        "total_tokens": 11529,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8700,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 10191,
        "total_tokens": 11529,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8700,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Identifying the topology\n\n| Device | Type | Gate | Source | Drain | Role |\n|---|---|---|---|---|---|\n| M₂ | NMOS | V_b1 (DC bias → AC ground) | V_in | V_out | **Common‑gate (CG) amplifier** |\n| M₁ | PMOS | V_b2 (DC bias → AC ground) | V_DD (AC ground) | V_out | **Current‑source (active) load** |\n\nThe signal enters the *source* of M₂ and leaves its *drain* while the gate is held at a constant voltage, so M₂ is a common‑gate device. M₁ has both gate and source at AC ground, so for small signals it is simply a resistor r_O1 from V_out to ground (an ideal current source if λ = 0).\n\n→ The circuit is a **CG stage with a current‑source load**.\n\n## 2. Bias (DC) considerations\n\n- Bias current is set by M₁:  \n  I_D = ½ μ_pC_ox(W/L)₁ (V_DD − V_b2 − |V_THP|)²\n- M₂ must carry the same current, so the DC level of the input and V_b1 must satisfy V_GS2 = V_b1 − V_in,DC = V_THN + √(2I_D / μ_nC_ox(W/L)₂).\n- Saturation conditions:\n  - M₂: V_out − V_in ≥ V_GS2 − V_THN ⇒ **V_out ≥ V_b1 − V_THN**\n  - M₁: V_DD − V_out ≥ V_SG1 − |V_THP| ⇒ **V_out ≤ V_b2 + |V_THP|**\n\nBecause the output node is high‑impedance, V_out,DC is very sensitive to current mismatch between M₁ and M₂ (a well‑known drawback of active loads).\n\n## 3. Small‑signal analysis (λ > 0)\n\nSmall‑signal model: v_gs2 = 0 − v_in = −v_in; dependent source g_m2·v_gs2 from drain to source of M₂; r_O2 between v_out and v_in; r_O1 from v_out to ground.\n\n**Voltage gain** – KCL at the output node:\n\n(v_in − v_out)/r_O2 + g_m2 v_in = v_out / r_O1\n\n$$\nA_v=\\frac{v_{out}}{v_{in}}=\\frac{(1+g_{m2}r_{O2})\\,r_{O1}}{r_{O1}+r_{O2}}\\;\\approx\\; g_{m2}\\,(r_{O1}\\parallel r_{O2})\n$$\n\nThe gain is **positive (non‑inverting)**, and of the same magnitude as a CS stage with a current‑source load.\n\n**Input impedance** (looking into the source of M₂, with r_O1 at its drain):\n\n$$\nR_{in}=\\frac{r_{O1}+r_{O2}}{1+g_{m2}r_{O2}}\\;\\approx\\;\\frac{1}{g_{m2}}\\left(1+\\frac{r_{O1}}{r_{O2}}\\right)\n$$\n\nNote it is *not* simply 1/g_m2: the load resistance r_O1 is \"seen\" through r_O2 and adds r_O1/(g_m2 r_O2). For r_O1 ≈ r_O2 the input resistance is about 2/g_m2.\n\n**Output impedance** (V_in set to zero → source of M₂ grounded):\n\n$$\nR_{out}=r_{O1}\\parallel r_{O2}\n$$\n\n(If the driving source has a finite resistance R_S, then R_out = r_O1 ∥ [r_O2 + (1+g_{m2}r_{O2})R_S] and A_v = (1+g_{m2}r_{O2})r_{O1} / [r_{O1}+r_{O2}+(1+g_{m2}r_{O2})R_S].)\n\n## 4. Limiting case and refinements\n\n- If λ = 0 (ideal current source, r_O → ∞): A_v → ∞, R_in = 1/g_m2, R_out → ∞. This is unrealistic—channel‑length modulation *must* be included for this circuit.\n- Body effect of M₂ (source not at ground): replace g_m2 by (g_m2 + g_mb2) in all expressions, e.g. A_v ≈ (g_m2+g_mb2)(r_O1 ∥ r_O2).\n- In terms of bias: A_v ≈ g_m2(r_O1∥r_O2) = √(2μ_nC_ox(W/L)₂/I_D) / (λ_n+λ_p); the gain rises as I_D is lowered.\n\n## 5. Summary\n\nA non‑inverting common‑gate amplifier (M₂) loaded by a PMOS current source (M₁):\n- A_v ≈ g_m2 (r_O1 ∥ r_O2) (large, positive)\n- R_in ≈ (1/g_m2)(1 + r_O1/r_O2) (low – useful for current‑mode/impedance‑matched inputs)\n- R_out = r_O1 ∥ r_O2 (high)\n- Output swing limited to V_b1 − V_THN ≤ V_out ≤ V_b2 + |V_THP|.",
        "format": "markdown",
        "sha256": "4e775bc1ce27b3c59675fadced8050b5dcf403ae1a79c0a527acf6e752f6bb3a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS with PMOS current-source load, places Vin at M2’s source, and gives the non-inverting gain and low input resistance. These satisfy the full-credit rule; the extra ideal-current-source limit does not change the essential answer.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 9821,
        "total_tokens": 11159,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8055,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 9821,
        "total_tokens": 11159,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8055,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Recognizing the topology\n\n| Device | Type (from the source arrow) | Terminals | Role |\n|---|---|---|---|\n| $M_1$ | PMOS (arrow pointing *into* the device at the $V_{DD}$ terminal) | source = $V_{DD}$, gate = $V_{b2}$ (dc), drain = $V_{out}$ | constant‑current (active) load |\n| $M_2$ | NMOS (arrow pointing *away* from the channel on the left terminal) | source = $V_{in}$, gate = $V_{b1}$ (dc), drain = $V_{out}$ | amplifying device, input at the **source** |\n\nSince the signal enters the source of $M_2$ and its gate is held at a fixed voltage, this is a **common‑gate (CG) stage with a PMOS current‑source load**. The current source replaces the drain resistor $R_D$ of the basic CG stage, which is what makes a large gain possible with little voltage headroom.\n\n## 2. DC operation\n\n- Both devices carry the same current: $I_{D1}=I_{D2}=I_D$.\n $I_D \\approx \\tfrac12\\mu_pC_{ox}(W/L)_1\\,(V_{DD}-V_{b2}-|V_{THp}|)^2 = \\tfrac12\\mu_nC_{ox}(W/L)_2\\,(V_{b1}-V_{IN}-V_{THn})^2$\n ($V_{IN}$ = dc level of the input; the input source must *sink* $I_D$, i.e. provide a dc path.)\n- Conduction: $V_{IN} < V_{b1}-V_{THn}$ and $V_{b2} < V_{DD}-|V_{THp}|$.\n- Saturation of $M_2$: $V_{out}\\ge V_{b1}-V_{THn}$ (= $V_{IN}+V_{OV2}$)\n Saturation of $M_1$: $V_{out}\\le V_{b2}+|V_{THp}|$ (= $V_{DD}-|V_{OV1}|$)\n\n $$V_{b1}-V_{THn}\\;\\le\\;V_{out}\\;\\le\\;V_{b2}+|V_{THp}|$$\n\n- Because the output node sees two high impedances, the dc value of $V_{out}$ is very sensitive to any mismatch between the two currents ($\\Delta V_{out}=\\Delta I\\,(r_{O1}\\|r_{O2})$); in practice this bias point is defined by feedback or by the biasing arrangement at the source of $M_2$.\n\n## 3. Small‑signal voltage gain\n\nSmall‑signal model:\n- $M_1$: gate and source are at ac ground ⇒ $v_{gs1}=0$ ⇒ $M_1$ reduces to its output resistance $r_{O1}$ from $V_{out}$ to ground.\n- $M_2$: $v_{gs2}=0-v_{in}=-v_{in}$; dependent source $g_{m2}v_{gs2}$ (drain→source) and $r_{O2}$ between drain and source.\n\nKCL at the output node:\n\n$$g_{m2}v_{in}+\\frac{v_{in}-v_{out}}{r_{O2}}=\\frac{v_{out}}{r_{O1}}$$\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=\\frac{g_{m2}+\\dfrac1{r_{O2}}}{\\dfrac1{r_{O1}}+\\dfrac1{r_{O2}}}=(1+g_{m2}r_{O2})\\frac{r_{O1}}{r_{O1}+r_{O2}}\n= g_{m2}(r_{O1}\\|r_{O2})+\\frac{r_{O1}}{r_{O1}+r_{O2}}\\;\\approx\\;g_{m2}(r_{O1}\\|r_{O2})}$$\n\nRemarks\n- The gain is **positive** (non‑inverting), as in any CG/CB stage.\n- Same as the short‑circuit‑transconductance method: $G_m=g_{m2}+1/r_{O2}$, $R_{out}=r_{O1}\\|r_{O2}$.\n- Special cases: \n – $\\lambda_2=0$: $A_v=g_{m2}r_{O1}$ (the familiar $g_mR_D$ with $R_D=r_{O1}$). \n – ideal load ($r_{O1}\\to\\infty$): $A_v\\to 1+g_{m2}r_{O2}$, the intrinsic gain of $M_2$ — the upper bound. \n – $\\lambda=0$ for both: $A_v\\to\\infty$ – unphysical; channel‑length modulation must be kept in this circuit.\n- In terms of design variables ($g_{m2}=2I_D/V_{OV2}$, $r_O=1/\\lambda I_D$):\n $A_v\\approx \\dfrac{2}{V_{OV2}\\,(\\lambda_n+\\lambda_p)}$ → use a small overdrive for $M_2$ and long channels for both devices; the gain is roughly independent of $I_D$.\n- Body effect (source of $M_2$ moves with the signal) simply replaces $g_{m2}$ by $g_{m2}+g_{mb2}$.\n\n## 4. Input impedance (looking into the source of $M_2$)\n\nWith the drain loaded by $r_{O1}$:\n\n$$R_{in}=\\frac{r_{O1}+r_{O2}}{1+g_{m2}r_{O2}}\\;\\approx\\;\\frac{1}{g_{m2}}\\Big(1+\\frac{r_{O1}}{r_{O2}}\\Big)$$\n\nLow, as expected for a CG stage, but noticeably larger than $1/g_{m2}$ because the large load resistance is \"reflected\" to the source (for $r_{O1}=r_{O2}$, $R_{in}\\approx 2/g_{m2}$). This matters when the stage is used for impedance matching (e.g. 50 Ω).\n\n## 5. Output impedance\n\n- Ideal input source: $R_{out}=r_{O1}\\,\\|\\,r_{O2}$.\n- With a source resistance $R_S$ at the input, $M_2$ boosts the impedance seen at its drain (cascode principle):\n $R_{out}=r_{O1}\\,\\|\\,[\\,r_{O2}+(1+g_{m2}r_{O2})R_S\\,]$, and the overall gain becomes\n $\\dfrac{v_{out}}{v_S}=\\dfrac{(1+g_{m2}r_{O2})\\,r_{O1}}{r_{O1}+r_{O2}+(1+g_{m2}r_{O2})R_S}$.\n\n## 6. Why this circuit (and a numerical feel)\n\nA resistor $R_D$ equal to $r_{O1}$ would drop $I_Dr_{O1}$ volts – usually far more than $V_{DD}$ – whereas the PMOS current source needs only $|V_{OV1}|$ of headroom while presenting $r_{O1}$ to the signal. Example: $I_D=0.5$ mA, $V_{OV2}=0.2$ V ⇒ $g_{m2}=5$ mS; $\\lambda_n=0.1$, $\\lambda_p=0.2\\ \\mathrm{V^{-1}}$ ⇒ $r_{O2}=20$ kΩ, $r_{O1}=10$ kΩ:\n\n$A_v\\approx 5\\,\\text{mS}\\times6.67\\,\\text{k}\\Omega+0.33\\approx 34$, $R_{in}\\approx 30\\,\\text{k}/101\\approx 0.3$ kΩ (vs $1/g_{m2}=0.2$ kΩ), $R_{out}\\approx 6.7$ kΩ.\n\n**Summary:** a non‑inverting common‑gate amplifier ($M_2$) loaded by a PMOS current source ($M_1$), with $A_v\\approx g_{m2}(r_{O1}\\|r_{O2})$ (exactly $(1+g_{m2}r_{O2})\\,r_{O1}/(r_{O1}+r_{O2})$), low input impedance $\\approx(r_{O1}+r_{O2})/(1+g_{m2}r_{O2})$, high output impedance $r_{O1}\\|r_{O2}$, and an output swing bounded by $V_{b1}-V_{THn}$ and $V_{b2}+|V_{THp}|$.",
        "format": "markdown",
        "sha256": "b5f2589e3b9771e18da3f5e5a45acfbf7339f45e8f95d193a34b9f9a6ff40171"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS stage with a PMOS current-source load, places Vin at M2’s source, identifies the bias voltages, and gives the non-inverting gain and low input resistance. Its gain expression is equivalent to the required approximation; omitted body effect and extra details do not detract.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 19228,
        "total_tokens": 20566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16336,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1338,
        "output_tokens": 19228,
        "total_tokens": 20566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16336,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- M₂ is a current‑source load whose gate is at a fixed (AC‑ground) potential, so C_GD2 and C_DB2 simply appear in parallel with C_DB from the output node to AC ground. The output capacitance is therefore C_out = C_DB + C_GD2 + C_DB2, and the output resistance is r_o1‖r_o2.\n\n- The circuit then has only two independent nodes: the gate of M₁ (node X) and the output node. Although three capacitors remain (C_GS, C_GD, C_out), they form a loop (X–ground, X–out, out–ground), so only two independent capacitor voltages (state variables) exist.\n\nWriting KCL at the two nodes gives a second‑order denominator:\n\nV_out/V_in = (C_GD s − g_m)R_D / [R_S R_D ξ s² + (R_S(1+g_mR_D)C_GD + R_S C_GS + R_D(C_GD + C_out))s + 1],\n\nwith ξ = C_GS C_GD + C_GS C_out + C_GD C_out and R_D = r_o1‖r_o2.\n\nSo the circuit has two poles (one associated mainly with the input node, one with the output node) and one zero at s = +g_m/C_GD.",
        "format": "markdown",
        "sha256": "2672566d3bb3dd32c273867aa2ab9ef6938d661e4b823180052e4b84bccd628f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the two independent nodes and assigns the gate, coupling, and output capacitances to the right places. The resulting second-order denominator (two poles) and the stated zero are consistent with the circuit.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 2144,
        "total_tokens": 4052,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1713,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 2144,
        "total_tokens": 4052,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1713,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- M₂ is a PMOS current source: its gate and source (and bulk) are at AC ground, so both C_GD2 and C_DB2 simply appear from the output node to AC ground. They are therefore in parallel with C_DB of M₁ and merge into one output capacitance, C_out = C_DB + C_GD2 + C_DB2. The load resistance is R_D = r_o1 ∥ r_o2.\n\n- What remains is the familiar CS stage with R_S, C_GS (input node to ground), C_GD (input node to output node), and C_out (output node to ground). These three capacitors form a loop (C_GS – C_GD – C_out through ground), so only two of their voltages can be set independently → only two independent energy‑storage states.\n\n- Equivalently, the circuit has only two nodes other than AC ground (the gate of M₁ and the output), giving a second‑order denominator:\n\nV_out/V_in = (C_GD·s − g_m)R_D / [R_S R_D ξ s² + (R_S(1+g_mR_D)C_GD + R_S C_GS + R_D(C_GD + C_out))s + 1],\n\nwith ξ = C_GS C_out + C_GS C_GD + C_GD C_out.\n\nSo despite the five capacitors drawn, the transfer function has exactly two poles (plus one zero at s = g_m/C_GD).",
        "format": "markdown",
        "sha256": "92e4ce7bd09dfd502801a5ef8db82d4013ca6b601d8563d6ff4c8022d245cf2b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two independent dynamic nodes—the M₁ gate and output—and assigns the capacitances to them accurately. The resulting second-order transfer function is consistent with two poles.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 1705,
        "total_tokens": 3613,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1239,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 1705,
        "total_tokens": 3613,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1239,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two poles.**\n\nReasoning:\n\n- The gate of M₂ is tied to a constant bias voltage (ac ground) and VDD is also ac ground, so C_GD2, C_DB2 and C_DB all appear **in parallel** between the output node and ground. They simply add up to one output capacitance: C_out = C_DB + C_GD2 + C_DB2.\n- The circuit therefore has only **two independent nodes** (the gate of M₁ and the output node), with C_GS (gate–ground), C_GD (gate–output) and C_out (output–ground). Because these three capacitors form a loop with ground, only two capacitor voltages are independent → the transfer function denominator is second order.\n\nHence the stage has two poles (and one zero at s = +g_m/C_GD):\n\n- Input pole (Miller approx.): ω_p,in ≈ 1 / { R_S [ C_GS + (1 + g_m1(r_O1‖r_O2)) C_GD ] }\n- Output pole: ω_p,out ≈ 1 / { (r_O1‖r_O2) [ C_DB + C_GD2 + C_DB2 + C_GD ] }",
        "format": "markdown",
        "sha256": "09ffee496c3e20511ceba6ebb20ae775d957d2e90107a7a2451aaf2bbca1fd21"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles from the gate and output nodes, with the capacitors assigned to the correct nodes. The additional pole estimates are consistent approximations.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 2744,
        "total_tokens": 4652,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2355,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1908,
        "output_tokens": 2744,
        "total_tokens": 4652,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2355,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the stacked‑gate CS stage\n\n## 1. What the circuit is\nTwo NMOS devices are stacked in series, both gates driven by the same voltage $V_{in}$, with a resistive load $R_D$. Call the intermediate node (drain of $M_1$ = source of $M_2$) $V_X$. Then (with zero gate current):\n\n$$I_{D1}=I_{D2}=I_D,\\qquad V_{GS1}=V_{in},\\qquad V_{GS2}=V_{in}-V_X,\\qquad V_{DS1}=V_X,\\qquad V_{out}=V_{DD}-R_DI_D .$$\n\n## 2. Regions of operation (the key observation)\nFor any current to flow, $M_2$ must be on:\n\n$$V_{GS2}>V_{TH}\\;\\Rightarrow\\;V_X<V_{in}-V_{TH}=V_{GS1}-V_{TH}.$$\n\nBut $V_{DS1}=V_X$, so $V_{DS1}<V_{GS1}-V_{TH}$: **$M_1$ can never be saturated – it is always in the triode region** whenever $M_2$ conducts. (Body effect raises $V_{TH2}$ because $V_{SB2}=V_X>0$, which only strengthens this conclusion.)\n\n$M_2$ is saturated if $V_{DS2}\\ge V_{GS2}-V_{TH}$, i.e. $V_{out}-V_X\\ge V_{in}-V_X-V_{TH}$:\n\n$$V_{out}\\ge V_{in}-V_{TH}$$\n\n— exactly the same condition as for an ordinary single‑transistor CS stage.\n\n## 3. Large‑signal behaviour: the pair is one \"long\" transistor\nLet $V_{ov}=V_{in}-V_{TH}$, $k_j=\\mu_nC_{ox}(W/L)_j$. With $M_1$ in triode and $M_2$ in saturation ($\\lambda=0$):\n\n$$I_D=k_1\\!\\left(V_{ov}V_X-\\tfrac{V_X^2}{2}\\right)=\\tfrac{k_1}{2}\\left[V_{ov}^2-(V_{ov}-V_X)^2\\right],\\qquad \nI_D=\\tfrac{k_2}{2}(V_{ov}-V_X)^2 .$$\n\nAdding $2I_D/k_1+2I_D/k_2$ eliminates $V_X$:\n\n$$\\boxed{I_D=\\tfrac12\\,k_{eq}\\,(V_{in}-V_{TH})^2},\\qquad \\frac1{k_{eq}}=\\frac1{k_1}+\\frac1{k_2}\\;\\Leftrightarrow\\;\\left(\\frac{L}{W}\\right)_{eq}=\\left(\\frac{L}{W}\\right)_1+\\left(\\frac{L}{W}\\right)_2 .$$\n\nSo $M_1$+$M_2$ behave like a single saturated NMOS with aspect ratio $(W/L)_{eq}$; for identical devices $(W/L)_{eq}=W/(2L)$ (one transistor of double length, half the current of a single device at the same $V_{in}$). The same algebra shows the equivalence also holds when both are in triode.\n\nIntermediate node: $V_X=V_{ov}\\left[1-\\sqrt{k_1/(k_1+k_2)}\\right]\\approx0.29\\,V_{ov}$ for identical devices (deep triode for $M_1$).\n\nOutput: \n$$V_{out}=V_{DD}-\\tfrac12 k_{eq}R_D\\,(V_{in}-V_{TH})^2 \\quad\\text{(valid while } V_{out}\\ge V_{in}-V_{TH}).$$\n\nTransfer characteristic: $V_{out}=V_{DD}$ for $V_{in}<V_{TH}$; parabolic drop for $V_{TH}<V_{in}<V_{in,max}$; beyond $V_{in,max}$ (where $V_{DD}-\\tfrac12k_{eq}R_DV_{ov}^2=V_{ov}$) $M_2$ also enters triode and the gain collapses.\n\n## 4. Small‑signal gain ($\\lambda=0$, no body effect)\nTriode $M_1$: $i_d=g_{m1}v_{in}+v_x/r_{on1}$, with $g_{m1}=k_1V_X$, $1/r_{on1}=k_1(V_{ov}-V_X)$.\nSaturated $M_2$: $i_d=g_{m2}(v_{in}-v_x)$, with $g_{m2}=k_2(V_{ov}-V_X)$.\n\nSolving,\n$$\\frac{i_d}{v_{in}}=g_{m2}\\frac{g_{m1}+1/r_{on1}}{g_{m2}+1/r_{on1}}=\\frac{k_1k_2}{k_1+k_2}V_{ov}=k_{eq}V_{ov}\\equiv G_m ,$$\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=-G_mR_D=-\\mu_nC_{ox}\\!\\left(\\frac{W}{L}\\right)_{eq}(V_{in}-V_{TH})R_D=-\\frac{2I_DR_D}{V_{in}-V_{TH}}}$$\n\ni.e. the gain of a CS stage using the composite transistor. For identical devices $A_v=-\\tfrac12\\mu_nC_{ox}(W/L)(V_{in}-V_{TH})R_D$, half that of a single‑transistor stage at the same gate bias.\n\nNote: treating $M_1$ merely as a degeneration resistor ($A_v=-R_D/(1/g_{m2}+R_{on1})$) is **wrong** here, because $M_1$'s gate is also driven by $v_{in}$ (the $g_{m1}$ term); that shortcut underestimates the gain (by $\\approx\\!0.71\\times$ for identical devices).\n\n## 5. Impedances\n- $R_{in}\\to\\infty$ (gate input, low frequency).\n- $R_{out}=R_D\\,\\|\\,[r_{o2}(1+g_{m2}R_{on1})+R_{on1}]\\approx R_D$ (with $v_{in}=0$, $M_1$ is just a resistor $R_{on1}$ degenerating $M_2$); exactly $R_D$ if $\\lambda=0$.\n\n## 6. Summary\n- $M_1$ is always in triode, $M_2$ is the \"real\" amplifying device (saturated as long as $V_{out}\\ge V_{in}-V_{TH}$).\n- The series pair with tied gates is equivalent to a single NMOS with $(L/W)_{eq}=(L/W)_1+(L/W)_2$; the circuit is simply a common‑source amplifier built with that composite transistor: $I_D=\\tfrac12 k_{eq}V_{ov}^2$, $A_v=-k_{eq}V_{ov}R_D$, $R_{out}\\approx R_D$.",
        "format": "markdown",
        "sha256": "61cc3d72bd33a5aab240104e93dfb10e127210880378458d485dda1acb00c0b4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate-driven series NMOS pair, places M1 in triode and M2 in saturation, and derives the key result: an effective channel length approximately equal to the sum of the two lengths. The extra analysis is consistent with the stated assumptions.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 11148,
        "total_tokens": 12679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 11148,
        "total_tokens": 12679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the stacked‑gate CS stage\n\n**Topology.** Two NMOS devices are stacked between $R_D$ and ground and *both gates are driven by* $V_{in}$. It looks like a cascode (M1 common‑source, M2 common‑gate), but the gate of M2 is not held at a fixed bias – it moves with the input. That single difference changes the behavior completely.\n\nCall the internal node (drain of M1 = source of M2) $X$. The same current $I_D$ flows in $R_D$, M2 and M1:\n\n$$V_{GS1}=V_{in},\\quad V_{DS1}=V_X,\\qquad V_{GS2}=V_{in}-V_X,\\quad V_{DS2}=V_{out}-V_X .$$\n\n---\n\n## 1. Regions of operation\n\nFor M2 to conduct at all: $V_{in}-V_X>V_{TH2}\\;\\Rightarrow\\;V_X<V_{in}-V_{TH2}$.\n\nSince $V_{TH2}\\ge V_{TH1}$ (body effect; equal if it is neglected),\n\n$$V_{DS1}=V_X<V_{in}-V_{TH1}=V_{GS1}-V_{TH1}\\quad\\Longrightarrow\\quad \\textbf{M1 is always in the triode region.}$$\n\nM1 cannot be saturated while M2 is on; it acts as a gate‑controlled resistor in the source of M2. **This is therefore not a cascode.**\n\nM2 is saturated if $V_{DS2}\\ge V_{GS2}-V_{TH2}$, i.e.\n\n$$V_{out}\\ \\ge\\ V_{in}-V_{TH2}\\qquad(\\text{same condition as an ordinary CS stage}).$$\n\n---\n\n## 2. The pair is equivalent to one transistor of length $L_1+L_2$\n\nAssume square‑law devices, equal $W$ and $V_{TH}$, $\\lambda=0$, no body effect. Writing the triode equation with all potentials referred to ground,\n\n$$I_D\\,L=\\mu_nC_{ox}W\\Big[(V_G-V_{TH})(V_D-V_S)-\\tfrac12\\big(V_D^2-V_S^2\\big)\\Big],$$\n\n$$\\text{M1: } I_D L_1=\\mu_nC_{ox}W\\Big[(V_{in}-V_{TH})V_X-\\tfrac12V_X^2\\Big]$$\n$$\\text{M2: } I_D L_2=\\mu_nC_{ox}W\\Big[(V_{in}-V_{TH})(V_{out}-V_X)-\\tfrac12\\big(V_{out}^2-V_X^2\\big)\\Big]$$\n\nAdding, $V_X$ cancels:\n\n$$I_D\\,(L_1+L_2)=\\mu_nC_{ox}W\\Big[(V_{in}-V_{TH})V_{out}-\\tfrac12V_{out}^2\\Big]$$\n\n– exactly one transistor with $W/(L_1+L_2)$, source grounded, drain at $V_{out}$. It pinches off at $V_{out}=V_{in}-V_{TH}$, i.e. precisely when M2 pinches off. Hence for identical devices the circuit is **a CS amplifier whose transistor has $W/(2L)$**:\n\n$$\\boxed{I_D=\\tfrac12\\mu_nC_{ox}\\frac{W}{2L}(V_{in}-V_{TH})^2=\\tfrac14\\mu_nC_{ox}\\frac{W}{L}(V_{in}-V_{TH})^2}$$\n\n$$V_{out}=V_{DD}-\\tfrac14\\mu_nC_{ox}\\frac{W}{L}(V_{in}-V_{TH})^2R_D,\\qquad\\text{valid while }V_{out}\\ge V_{in}-V_{TH}.$$\n\n**Internal node.** Equating M1 (triode) and M2 (saturation) currents with $V_{OV}=V_{in}-V_{TH}$:\n\n$$V_{OV}V_X-\\tfrac12V_X^2=\\tfrac12(V_{OV}-V_X)^2\\;\\Rightarrow\\;V_X=\\Big(1-\\tfrac{1}{\\sqrt2}\\Big)V_{OV}\\approx0.29\\,V_{OV}$$\n\nso M2 has overdrive $V_{OV}/\\sqrt2$ and M1 sits at $V_{DS1}\\approx0.29V_{OV}$ (well inside triode). (General case: $V_X=V_{OV}\\big[1-\\sqrt{L_2/(L_1+L_2)}\\big]$ – just the channel potential of a long device at distance $L_1$ from the source.)\n\n---\n\n## 3. Small‑signal behavior ($\\lambda=0$)\n\nUsing the equivalent device:\n\n$$g_{m,eq}=\\frac{\\partial I_D}{\\partial V_{in}}=\\tfrac12\\mu_nC_{ox}\\frac{W}{L}(V_{in}-V_{TH})=\\sqrt{\\mu_nC_{ox}\\frac{W}{L}I_D}$$\n\n$$\\boxed{A_v=-g_{m,eq}R_D=-\\tfrac12\\mu_nC_{ox}\\frac{W}{L}(V_{in}-V_{TH})R_D=-\\frac{2I_DR_D}{V_{in}-V_{TH}}}$$\n\n$R_{in}=\\infty$ (low frequency), $R_{out}=R_D$.\n\n**Check with the explicit small‑signal model** (shows *why*). With $k=\\mu_nC_{ox}W/L$:\n\n- M1 (triode): $g_{m1}=kV_X$, $g_{o1}=1/R_{on1}=k(V_{OV}-V_X)$\n- M2 (sat.): $g_{m2}=k(V_{OV}-V_X)$ → note $g_{o1}=g_{m2}$, i.e. $R_{on1}=1/g_{m2}$.\n\nCurrent continuity at X: $g_{m1}v_{in}+g_{o1}v_x=g_{m2}(v_{in}-v_x)$\n\n$$\\Rightarrow\\ i_d=g_{m2}\\frac{g_{m1}+g_{o1}}{g_{m2}+g_{o1}}\\,v_{in}=\\frac{kV_{OV}}{2}\\,v_{in}\\quad\\checkmark$$\n\n(General lengths: $G_m=\\mu_nC_{ox}\\,W\\,V_{OV}/(L_1+L_2)$.) M1's on‑resistance degenerates M2, but M1's gate is also driven, which partly compensates; the net result is exactly the $g_m$ of a $2L$ device.\n\n---\n\n## 4. Effect of $\\lambda$ and body effect\n\n- Looking into the drain of M2 (M1 = resistor $R_{on1}$ since its gate is at AC ground):\n $$R_{out,M}=r_{o2}+R_{on1}+g_{m2}r_{o2}R_{on1}\\approx 2r_{o2}\\quad(R_{on1}=1/g_{m2})$$\n – again the $r_o$ of a device of length $2L$ ($\\lambda_{eq}=\\lambda/2$). There is **no cascode boost** ($g_{m2}r_{o2}r_{o1}$) because M1 is in triode. Then $A_v\\approx-g_{m,eq}\\,(R_D\\parallel 2r_o)$.\n- Body effect raises $V_{TH2}$ (its source is at $V_X>0$): $I_D$ and the gain drop slightly, $g_{mb2}$ appears in the denominator of $G_m$. Physically the structure is still one long channel.\n\n---\n\n## 5. Transfer characteristic and swing\n\n- $V_{in}<V_{TH}$: $I_D=0$, $V_{out}=V_{DD}$.\n- $V_{TH}<V_{in}$ up to the point where $V_{DD}-\\tfrac14kR_D(V_{in}-V_{TH})^2=V_{in}-V_{TH}$: quadratic drop, M2 saturated (gain region).\n- Beyond that M2 enters triode; the composite device behaves as a $2L$ triode device and $V_{out}\\to$ small.\n- Minimum output for linear operation: $V_{out,min}=V_{in}-V_{TH}$ (set by M2; M1 imposes no extra constraint).\n\n---\n\n## 6. Takeaways / comparison with an ordinary CS stage (single $W/L$)\n\n| | single device $W/L$ | this circuit |\n|---|---|---|\n| effective device | $W/L$ | $W/2L$ |\n| same $V_{in}$ | $I_D$, $g_m$ | $I_D/2$, $g_m/2$ → gain halves |\n| same $I_D$ | $g_m$ | $g_m/\\sqrt2$ (needs $\\sqrt2\\times$ overdrive) |\n| $r_o$ | $r_o$ | $\\approx 2r_o$ (intrinsic gain $g_mr_o$ unchanged) |\n| M1 region | saturation | **triode** |\n\nConclusion: tying both gates to the input turns the \"cascode\" into a plain common‑source stage built from an effectively longer transistor. The bottom device is forced into triode, the gain is $A_v=-\\tfrac12\\mu_nC_{ox}\\tfrac{W}{L}(V_{in}-V_{TH})R_D$ (half that of a single device at the same overdrive), and none of the shielding or output‑resistance benefits of a true cascode (fixed $V_b$ on M2's gate) are obtained.",
        "format": "markdown",
        "sha256": "911a47e469f3d2c77d82732c0d933254cff4678162b03e25a4048d9f7b8c509e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the shared-gate series NMOS structure, the lower device’s triode operation, and the effective channel length of approximately L1 + L2. Its output-resistance discussion also matches the golden solution; ideal-model simplifications do not change the central result.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 20362,
        "total_tokens": 21893,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17061,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 20362,
        "total_tokens": 21893,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17061,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## What the circuit is\n\nM1 and M2 are two NMOS devices stacked in series, **both gates driven by V_in**, with a resistive load R_D. It looks like a cascode, but it is *not* one: the upper device's gate is not held at a fixed bias, it moves with the input. Below, V_ov ≡ V_in − V_TH, k_n ≡ μ_nC_ox, and X is the node between the transistors (drain of M1 = source of M2). λ = 0 and body effect neglected unless stated.\n\n---\n\n## 1. Regions of operation (the key observation)\n\n- M1: V_GS1 = V_in, V_DS1 = V_X  \n- M2: V_GS2 = V_in − V_X, V_DS2 = V_out − V_X\n\nFor any current to flow, M2 must be on:\n\n$$V_{in}-V_X > V_{TH}\\;\\;\\Rightarrow\\;\\; V_X < V_{in}-V_{TH}=V_{GS1}-V_{TH}\\;\\;\\Rightarrow\\;\\; V_{DS1}<V_{GS1}-V_{TH}$$\n\n**So M1 can never be in saturation – it is always in the triode region whenever the circuit conducts.** (Intuitively: both gates sit at the same voltage but M2's source is above ground, so M2 always has the smaller V_GS; to carry the *same* current M1 must be \"throttled,\" i.e., in triode. Body effect raises V_TH2 and only strengthens this.)\n\nM2 is saturated when V_DS2 ≥ V_GS2 − V_TH, i.e.\n\n$$V_{out}-V_X \\ge V_{in}-V_X-V_{TH}\\;\\;\\Longleftrightarrow\\;\\; V_{out}\\ge V_{in}-V_{TH},$$\n\nexactly the same condition as for an ordinary single‑transistor CS stage.\n\n---\n\n## 2. Large‑signal behavior: the stack is one \"long\" transistor\n\nIn the amplifying region (M1 triode, M2 saturated):\n\n$$I_D = k_n\\Big(\\tfrac{W}{L}\\Big)_1\\Big[V_{ov}V_X-\\tfrac{V_X^2}{2}\\Big],\\qquad \nI_D = \\tfrac{1}{2}k_n\\Big(\\tfrac{W}{L}\\Big)_2\\,(V_{ov}-V_X)^2$$\n\nRewrite as 2I_D/[k_n(W/L)_1] = 2V_ovV_X − V_X² and 2I_D/[k_n(W/L)_2] = V_ov² − 2V_ovV_X + V_X², and add — V_X cancels:\n\n$$\\boxed{I_D=\\tfrac12 k_n\\Big(\\tfrac{W}{L}\\Big)_{eff}(V_{in}-V_{TH})^2},\\qquad \n\\frac{1}{(W/L)_{eff}}=\\Big(\\frac{L}{W}\\Big)_1+\\Big(\\frac{L}{W}\\Big)_2$$\n\nFor equal widths, L_eff = L₁ + L₂; for identical devices (W/L)_eff = (W/L)/2. (The same result holds when both are in triode, so the stack is *exactly* equivalent to a single NMOS of length L₁+L₂ under the square‑law model — physically, M1 is just the un‑pinched part of a long channel and M2 the pinched‑off part near the drain.)\n\nHence\n\n$$V_{out}=V_{DD}-R_D\\cdot\\tfrac12 k_n\\Big(\\tfrac{W}{L}\\Big)_{eff}(V_{in}-V_{TH})^2 .$$\n\nIntermediate node (identical devices): 2V_X² − 4V_ovV_X + V_ov² = 0 ⇒\n\n$$V_X=\\Big(1-\\tfrac{1}{\\sqrt2}\\Big)V_{ov}\\approx0.29\\,V_{ov},\\qquad V_{GS2}-V_{TH}=\\tfrac{V_{ov}}{\\sqrt2}\\approx0.71\\,V_{ov}$$\n\nTransfer characteristic: V_in < V_TH → both off, V_out = V_DD; V_TH < V_in with V_out ≥ V_in − V_TH → square‑law (amplifying) region above; beyond that M2 also enters triode and V_out collapses toward zero — identical in shape to a CS stage with a device of (W/L)_eff.\n\n---\n\n## 3. Small‑signal gain\n\nBecause I_D(V_in) is a square law with (W/L)_eff, the effective transconductance is\n\n$$G_m=\\frac{dI_D}{dV_{in}}=k_n\\Big(\\tfrac{W}{L}\\Big)_{eff}V_{ov}=\\sqrt{2k_n(W/L)_{eff}I_D}=\\frac{2I_D}{V_{ov}}$$\n\n$$\\boxed{A_v=-G_mR_D=-k_n\\Big(\\tfrac{W}{L}\\Big)_{eff}(V_{in}-V_{TH})R_D}$$\n\nFor identical devices: A_v = −½·k_n(W/L)(V_in − V_TH)R_D, i.e. **half the gain** of M1 alone at the same V_in (or 1/√2 of it at the same drain current).\n\n*Check with explicit small‑signal models* (identical devices, k ≡ k_n W/L). M1 in triode: i_d1 = g_m1 v_in + v_x/R_on1 with g_m1 = kV_X and 1/R_on1 = k(V_ov − V_X). M2 saturated: i_d2 = g_m2(v_in − v_x), g_m2 = k(V_ov − V_X) = 1/R_on1. KCL at X:\n\n$$v_x=\\frac{g_{m2}-g_{m1}}{g_{m2}+1/R_{on1}}v_{in}\\approx0.29\\,v_{in},\\qquad\ni_{out}=g_{m2}\\frac{g_{m1}+1/R_{on1}}{g_{m2}+1/R_{on1}}\\,v_{in}=\\frac{kV_{ov}}{2}v_{in}\\;✓$$\n\n---\n\n## 4. Output resistance, λ and body effect\n\nWith v_in = 0, M1 is just a resistor R_on1 degenerating M2:\n\n$$R_{out}=R_D\\,\\|\\,\\big[r_{o2}(1+(g_{m2}+g_{mb2})R_{on1})+R_{on1}\\big]\\approx R_D\\,\\|\\,2r_{o2}$$\n\n(for identical devices, since g_m2R_on1 = 1) — consistent with a device of twice the length having half the λ. Then A_v ≈ −G_m(R_D ‖ 2r_o2).\n\nBody effect: M2's source sits at V_X ≈ 0.29V_ov, so V_TH2 > V_TH1. This lowers I_D and G_m somewhat and pushes V_X lower (M1 even deeper in triode); the qualitative conclusions are unchanged.\n\n---\n\n## 5. Summary\n\n| Property | This stack (identical M1, M2) | Single CS device (W/L) at same V_in |\n|---|---|---|\n| M1 region | triode (always) | saturation |\n| M2 region | saturation if V_out ≥ V_in − V_TH | — |\n| I_D | ½k_n(W/2L)V_ov² (half) | ½k_n(W/L)V_ov² |\n| G_m | k_n(W/2L)V_ov (half) | k_n(W/L)V_ov |\n| A_v (λ=0) | −½k_n(W/L)V_ovR_D | −k_n(W/L)V_ovR_D |\n| r_o of device | ≈2r_o | r_o |\n\nBottom line: the circuit is a **common‑source amplifier whose transistor is a composite device of length L₁+L₂**, not a cascode. It buys higher output resistance and uses unit‑length devices, at the cost of lower transconductance, more area, a higher input voltage for a given current, and an extra internal node (X) that adds capacitance/a pole.\n\n(Numerical illustration: k_nW/L = 11.1 mA/V², V_TH = 0.4 V, V_in = 0.8 V, R_D = 1 kΩ, V_DD = 1.8 V → I_D = 0.44 mA, V_X ≈ 0.12 V, V_out ≈ 1.36 V (M2 saturated), G_m = 2.2 mA/V, A_v ≈ −2.2 versus −4.4 for M1 alone.)",
        "format": "markdown",
        "sha256": "f4251a03e67035ee8cb5a4b4d355f82aa957580a8e5a370370dd40e8d63669c6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate series NMOS stack, with M1 in triode and M2 saturated, and reaches the essential conclusion that it behaves approximately like a device with effective channel length L1 + L2. Its distinction from a true cascode and supporting analysis are consistent with the golden solution.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 16427,
        "total_tokens": 17958,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13511,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1531,
        "output_tokens": 16427,
        "total_tokens": 17958,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13511,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n- **M1**: gate = V_in, drain = V_DD (ac ground), source = node P → a **source follower** (common‑drain stage).\n- **M2**: gate = V_b (dc bias, ac ground), source = node P, drain = V_out through R_D → a **common‑gate stage**.\n- **I₁**: ideal tail current source → forces I_D1 + I_D2 = I₁ (no small‑signal current can leave node P).\n\nSo the circuit is a *source follower driving a common‑gate stage*; it is also exactly a differential pair with one input ac‑grounded and the output taken single‑ended from the drain of M2.\n\nSignal path: V_in ↑ → V_P ↑ (follower) → V_GS2 ↓ → I_D2 ↓ → V_out ↑. The gain is therefore **non‑inverting**.\n\n## 2. DC operating point\n\n$$I_{D1}+I_{D2}=I_1,\\qquad V_P=V_{in,DC}-V_{GS1}=V_b-V_{GS2}$$\n\nIf M1 and M2 are identical and V_in,DC = V_b: I_D1 = I_D2 = I₁/2,\n\n$$V_{out,DC}=V_{DD}-R_D\\frac{I_1}{2},\\qquad g_m=\\sqrt{2\\mu_nC_{ox}\\tfrac{W}{L}\\cdot\\tfrac{I_1}{2}}=\\sqrt{\\mu_nC_{ox}\\tfrac{W}{L}I_1}$$\n\nSaturation conditions:\n- M1: drain tied to V_DD → always saturated.\n- M2: V_out ≥ V_b − V_TH, i.e. V_DD − I_D2R_D ≥ V_b − V_TH (worst case I_D2 = I₁).\n- I₁ needs headroom: V_P = V_b − V_GS2 must exceed the minimum voltage of the current source.\n\nLarge‑signal range: for |V_in − V_b| > √(2I₁/(μ_nC_ox W/L)) one transistor turns off; V_out saturates at V_DD (M2 off) or at V_DD − I₁R_D (M1 off).\n\n## 3. Small‑signal gain (λ = 0, no body effect)\n\nKCL at node P (ideal I₁): i_d1 + i_d2 = 0\n\n$$g_{m1}(v_{in}-v_P)=g_{m2}v_P\\;\\Rightarrow\\; v_P=\\frac{g_{m1}}{g_{m1}+g_{m2}}v_{in}=\\frac{1/g_{m2}}{1/g_{m1}+1/g_{m2}}\\,v_{in}$$\n\n$$v_{out}=-i_{d2}R_D=g_{m2}R_D\\,v_P$$\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=\\frac{g_{m1}g_{m2}R_D}{g_{m1}+g_{m2}}=\\frac{R_D}{\\dfrac{1}{g_{m1}}+\\dfrac{1}{g_{m2}}}}$$\n\nTwo equivalent ways to read this:\n1. Follower M1 loaded by the CG input resistance 1/g_m2 → gain (1/g_m2)/(1/g_m1+1/g_m2); CG stage M2 → gain g_m2R_D; multiply.\n2. M1 is a CS stage degenerated by R_S = 1/g_m2: its signal current is v_in/(1/g_m1+1/g_m2). Since I₁ is fixed, that current is \"stolen\" from M2 and flows out of R_D, raising V_out by i·R_D.\n\nFor matched devices (g_m1 = g_m2 = g_m):\n\n$$A_v=\\frac{g_mR_D}{2}$$\n\ni.e., half the gain of a plain CS stage, because v_in is split equally between V_GS1 and V_GS2 (this is the familiar single‑ended gain of a differential pair).\n\nImpedances: R_in = ∞ (gate), R_out = R_D.\n\n## 4. Refinements\n\n**Body effect** (λ = 0): g_mb1 adds conductance at node P, g_mb2 adds to the CG transconductance:\n\n$$A_v=\\frac{g_{m1}(g_{m2}+g_{mb2})R_D}{g_{m1}+g_{mb1}+g_{m2}+g_{mb2}}$$\n\n(for matched devices this is still g_mR_D/2 – the body effect cancels, consistent with the differential‑pair view).\n\n**Channel‑length modulation**: let R_in2 = (R_D + r_O2)/(1 + g_m2r_O2) (CG input resistance). Then\n\n$$A_v=\\underbrace{\\frac{g_{m1}(r_{O1}\\|R_{in2})}{1+g_{m1}(r_{O1}\\|R_{in2})}}_{\\text{follower}}\\cdot\\underbrace{\\frac{(1+g_{m2}r_{O2})R_D}{R_D+r_{O2}}}_{\\text{CG}}$$\n\n$$R_{out}=R_D\\,\\Big\\|\\,\\Big[r_{O2}+(1+g_{m2}r_{O2})\\big(r_{O1}\\|\\tfrac{1}{g_{m1}}\\big)\\Big]$$\n\nBoth reduce to the results in Section 3 as r_O → ∞.\n\n**Summary:** a non‑inverting amplifier formed by a source follower (M1) feeding a common‑gate stage (M2), with voltage gain R_D/(1/g_m1 + 1/g_m2) ≈ g_mR_D/2 for matched transistors, infinite input resistance, and output resistance ≈ R_D.",
        "format": "markdown",
        "sha256": "7a087b5c274479d11609c8b022423e7effecb9e2f2617e80accd633337f4321f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower driving a common-gate stage (equivalently, a source-coupled pair with M2 biased at Vb) and gives the correct non-inverting gain. Full-credit rule applies.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11469,
        "total_tokens": 13946,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9516,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11469,
        "total_tokens": 13946,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9516,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. Recognizing the topology\n\n| Device | Gate | Drain | Source | Configuration |\n|---|---|---|---|---|\n| M1 | V_in | V_DD (ac ground) | node P | **source follower** (common‑drain) |\n| M2 | V_b (dc bias → ac ground) | V_out via R_D | node P | **common‑gate** stage |\n\nBoth sources share one tail current source I₁. So the circuit is a **source follower (M1) driving a common‑gate stage (M2)**. Equivalently, it is a **differential pair whose second input is tied to a fixed bias V_b**, with a single‑ended output taken at the drain of M2 (M1's drain has no load, so no output is taken there).\n\nBecause I₁ is constant,\n\nI_D1 + I_D2 = I₁  ⇒ any increase in I_D1 is an equal decrease in I_D2.\n\nThat single fact explains the whole operation: M1 converts V_in into a current change, and that current change is \"stolen\" from M2 and delivered to R_D.\n\n---\n\n## 2. DC bias and large‑signal behavior\n\n- Node P sits at V_P = V_in(dc) − V_GS1 = V_b − V_GS2.\n- The split of I₁ is set by V_in − V_b. With matched devices and V_in(dc) = V_b: I_D1 = I_D2 = I₁/2 and V_out = V_DD − R_D·I₁/2.\n- Square‑law (λ = 0), ΔV = V_in − V_b:\n\n I_D1 − I_D2 = ½ μₙC_ox(W/L)·ΔV·√(4I₁/(μₙC_ox W/L) − ΔV²)\n\n V_out = V_DD − R_D·I_D2 = V_DD − R_D I₁/2 + (R_D/2)(I_D1 − I_D2)\n\n- Transfer characteristic is **non‑inverting**:\n V_in ↑ → V_P ↑ → V_GS2 ↓ → I_D2 ↓ → V_out ↑.\n- Limits: for ΔV ≤ −√2·V_OV all of I₁ flows in M2 → V_out = V_DD − I₁R_D (minimum). For ΔV ≥ +√2·V_OV M2 is off → V_out = V_DD (maximum). (V_OV = overdrive at I₁/2.)\n- Saturation conditions: M1 is essentially always saturated (drain at V_DD). M2 needs V_out ≥ V_b − V_TH, i.e. V_DD − I_D2R_D ≥ V_b − V_TH. I₁ needs V_P = V_b − V_GS2 larger than its compliance voltage. V_b therefore sets both the current split and the headroom.\n\n---\n\n## 3. Small‑signal gain (λ = 0, no body effect)\n\nSmall‑signal currents (drain→source) with v_P the voltage at node P:\n\n- M1: i₁ = g_m1(v_in − v_P)\n- M2: i₂ = g_m2(0 − v_P) = −g_m2 v_P\n\nIdeal I₁ carries no signal current, so KCL at P: i₁ + i₂ = 0\n\n g_m1(v_in − v_P) = g_m2 v_P ⇒ **v_P = v_in · g_m1/(g_m1 + g_m2)**\n\nThe output: v_out = −R_D·i₂ = g_m2 R_D v_P, hence\n\n**A_v = v_out/v_in = g_m1 g_m2 R_D/(g_m1 + g_m2) = R_D / (1/g_m1 + 1/g_m2)**\n\nTwo‑stage view that gives the same result:\n- Source follower M1 loaded by the input resistance of the CG stage, 1/g_m2:\n A₁ = (1/g_m2)/(1/g_m1 + 1/g_m2) = g_m1/(g_m1+g_m2)\n- Common‑gate stage: A₂ = g_m2 R_D\n\nSpecial case g_m1 = g_m2 = g_m (equal devices, equal currents):\n\n **A_v = g_m R_D / 2**\n\n— exactly the single‑ended gain of a differential pair driven at one input, and half the gain of a plain CS or CG stage with the same g_m and R_D. The \"lost\" factor of 2 is the voltage division between 1/g_m1 and 1/g_m2 at node P (the follower only delivers half the input swing to M2's source). Making g_m1 ≫ g_m2 pushes the gain toward g_m2R_D.\n\n---\n\n## 4. Including non‑idealities\n\n**Body effect** (bodies at ground): replace each g_m by (g_m + g_mb) where the source moves, except that the input transconductance of M1 stays g_m1:\n\n A_v = g_m1(g_m2 + g_mb2)R_D / (g_m1 + g_mb1 + g_m2 + g_mb2)\n\nBody effect in M1 lowers the gain; body effect in M2 slightly helps (acts like a larger g_m2).\n\n**Channel‑length modulation** (finite r_o1, r_o2): the CG input resistance becomes R_in2 = (R_D + r_o2)/(1 + g_m2 r_o2), and\n\n A_v = g_m1 R_D / [1 + (g_m1 + 1/r_o1)(R_D + r_o2)/(1 + g_m2 r_o2)]\n\nwhich reduces to the λ = 0 result when r_o1, r_o2 → ∞.\n\n---\n\n## 5. Port impedances\n\n- **Input impedance:** infinite at low frequency (gate of M1). At high frequency C_in ≈ C_GD1 + C_GS1·(1 − v_P/v_in) ≈ C_GD1 + C_GS1·g_m2/(g_m1+g_m2) — no Miller multiplication (drain of M1 is at ac ground).\n- **Output impedance:** with λ = 0, R_out = R_D. With finite r_o, M2 is degenerated by the resistance seen at P, R_S = r_o1 ∥ 1/g_m1:\n R_out = R_D ∥ [r_o2 + R_S + g_m2 r_o2 R_S] ≈ R_D ∥ r_o2(1 + g_m2/g_m1) ≈ R_D ∥ 2r_o2 for equal g_m.\n- Node P is a low‑impedance node, ≈ 1/(g_m1 + g_m2), so the pole there is at high frequency; C_GD2 is also not Miller‑multiplied (gate of M2 is ac ground). The structure is therefore wideband.\n\n---\n\n## 6. Summary of the circuit's character\n\n- Non‑inverting amplifier, A_v = R_D/(1/g_m1 + 1/g_m2) → g_mR_D/2 for matched devices.\n- Very high input impedance (unlike a bare common‑gate stage, whose input impedance is 1/g_m), yet it keeps the common‑gate stage's freedom from the Miller effect.\n- Output swing: V_DD − I₁R_D ≤ V_out ≤ V_DD; linear range of input ≈ ±√2·V_OV around V_b.\n- It is the same circuit as a differential pair with one input grounded, which is why the gain is half the g_mR_D of a single CS stage; the \"missing\" half of the signal is available (inverted) at M1's drain if a second R_D is added there.",
        "format": "markdown",
        "sha256": "a9143359aaeefa407452c49e8b02e0e5ce25b4e1bb382f9b3c88daf0a7922983"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower driving M2 as a common-gate stage (also a source-coupled pair), and gives the correct non-inverting gain. This meets the golden solution’s full-credit rule.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11104,
        "total_tokens": 13581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8599,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11104,
        "total_tokens": 13581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8599,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n- **M1** has its drain tied directly to V_DD, its gate driven by V_in, and its output taken at the source → it is a **source follower (common‑drain stage)**.\n- **M2** has its gate at the fixed bias V_b, its input at the source, and its output at the drain through R_D → it is a **common‑gate stage**.\n- The two sources share node P, which is biased by the tail current I₁.\n\nSo the circuit is a **source follower driving a common‑gate amplifier** – which is exactly a differential pair (inputs V_in and V_b) with a single‑ended output taken at the drain of M2. Only M2 has a load; M1 just transfers the signal to node P.\n\n## 2. Bias (large‑signal) behaviour\n\nWith the tail current fixed:\n\n$$I_{D1}+I_{D2}=I_1,\\qquad V_{GS1}-V_{GS2}=V_{in}-V_b\\equiv \\Delta V_{in}$$\n\nFor identical square‑law devices ($k=\\mu_nC_{ox}W/L$):\n\n$$I_{D1}-I_{D2}=\\frac{k}{2}\\,\\Delta V_{in}\\sqrt{\\frac{4I_1}{k}-\\Delta V_{in}^2},\\qquad |\\Delta V_{in}|\\le\\sqrt{2I_1/k}$$\n\n$$V_{out}=V_{DD}-R_D I_{D2}=V_{DD}-\\frac{R_D}{2}\\Big[I_1-(I_{D1}-I_{D2})\\Big]$$\n\n- $V_{in}=V_b$: each device carries $I_1/2$, $V_P=V_b-V_{GS}$, $V_{out}=V_{DD}-I_1R_D/2$.\n- $V_{in}\\gg V_b$: all of $I_1$ flows in M1, M2 turns off, $V_{out}\\to V_{DD}$.\n- $V_{in}\\ll V_b$: all of $I_1$ flows in M2, $V_{out}\\to V_{DD}-I_1R_D$.\n\nSo $V_{out}$ rises with $V_{in}$ (noninverting) and swings between $V_{DD}-I_1R_D$ and $V_{DD}$.\n\nOperating‑region requirements:\n- M2 saturated: $V_{DD}-I_{D2}R_D\\ge V_b-V_{TH}$ (worst case $V_{DD}-I_1R_D\\ge V_b-V_{TH}$).\n- M1 is always saturated (drain at $V_{DD}$, since $V_{DD}\\ge V_{in}-V_{TH}$).\n- The current source needs headroom: $V_P=V_b-V_{GS2}$ must exceed its minimum compliance voltage.\n\n## 3. Small‑signal gain (λ = 0, no body effect)\n\nIn small signal the ideal current source is an open circuit, so the two small‑signal drain currents must cancel at node P:\n\n$$i_{d1}+i_{d2}=0\\;\\Rightarrow\\; g_{m1}(v_{in}-v_P)=g_{m2}v_P\\;\\Rightarrow\\;\nv_P=\\frac{g_{m1}}{g_{m1}+g_{m2}}\\,v_{in}=\\frac{1/g_{m2}}{1/g_{m1}+1/g_{m2}}\\,v_{in}$$\n\nInterpretation: the follower M1 (output resistance $1/g_{m1}$) is loaded by the input resistance of the CG stage ($1/g_{m2}$) – a resistive divider.\n\nThe CG stage then gives $v_{out}=-R_D i_{d2}=g_{m2}R_D\\,v_P$, so\n\n$$\\boxed{A_v=\\frac{v_{out}}{v_{in}}=\\frac{g_{m1}g_{m2}R_D}{g_{m1}+g_{m2}}=\\frac{R_D}{\\dfrac{1}{g_{m1}}+\\dfrac{1}{g_{m2}}}}$$\n\nFor identical devices ($g_{m1}=g_{m2}=g_m$):\n\n$$A_v=+\\frac{g_mR_D}{2},\\qquad g_m=\\sqrt{\\mu_nC_{ox}\\frac{W}{L}I_1}$$\n\n(Same result obtained by differentiating the large‑signal characteristic at $\\Delta V_{in}=0$.) The gain is positive and half that of a simple CS stage because the signal is split equally between the two $1/g_m$ resistances at node P. In general it is bounded by $\\min(g_{m1},g_{m2})R_D$.\n\nAdding body effect: $A_v=\\dfrac{g_{m1}(g_{m2}+g_{mb2})R_D}{g_{m1}+g_{mb1}+g_{m2}+g_{mb2}}$.\n\n## 4. Including channel‑length modulation (r_O1, r_O2 finite, I₁ ideal)\n\nInput resistance of the CG stage: $R_{in,CG}=\\dfrac{R_D+r_{O2}}{1+g_{m2}r_{O2}}$\n\n$$\\frac{v_P}{v_{in}}=\\frac{r_{O1}\\|R_{in,CG}}{r_{O1}\\|R_{in,CG}+1/g_{m1}},\\qquad\n\\frac{v_{out}}{v_P}=\\frac{(1+g_{m2}r_{O2})R_D}{R_D+r_{O2}}$$\n\n$$A_v=\\frac{g_{m1}(1+g_{m2}r_{O2})R_D}{(g_{m1}+1/r_{O1})(R_D+r_{O2})+1+g_{m2}r_{O2}}\n\\;\\xrightarrow{r_O\\to\\infty}\\;\\frac{g_{m1}g_{m2}R_D}{g_{m1}+g_{m2}}$$\n\n## 5. Input and output impedances\n\n- $R_{in}=\\infty$ (gate of M1) – this is the main benefit over a plain CG stage, whose input resistance is only $1/g_m$.\n- $R_{out}=R_D$ for λ = 0; in general\n$$R_{out}=R_D\\,\\Big\\|\\,\\Big[r_{O2}+(1+g_{m2}r_{O2})\\big(r_{O1}\\|\\tfrac{1}{g_{m1}}\\big)\\Big]$$\n\n## 6. Summary / remarks\n\n- Noninverting amplifier, $A_v\\approx g_mR_D/2$, infinite input impedance, output impedance ≈ $R_D$.\n- Because neither transistor is a common‑source device with a gain across its $C_{GD}$, there is **no Miller effect**, so the stage is fast (follower + CG), at the cost of half the gain of a CS stage.\n- Viewed with $V_b$ as a second input, $v_{out}\\approx \\frac{g_mR_D}{2}(v_{in}-v_b)$: it is a differential pair with single‑ended output, and the follower‑plus‑CG decomposition is precisely the \"superposition\" way of analyzing a differential pair driven at one input.",
        "format": "markdown",
        "sha256": "d97475674d66f39b0d104c0108d79a9f63d99c5703440169e4f68fc80d88877e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-follower driving a common-gate stage (equivalently, the source-coupled pair) and gives the non-inverting gain, matching the essential answer.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11417,
        "total_tokens": 13894,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8996,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2477,
        "output_tokens": 11417,
        "total_tokens": 13894,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8996,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Circuit:** M₁ is a source follower, M₂ is its current‑source load, and the input is driven through a series resistance R_S. The only element needed to explain the effect is the gate–source capacitance C_GS of M₁ (ignore C_GD, C_SB, r_O, body effect for simplicity).\n\n**Derivation of Z_out**\n\nSet V_in = 0, apply a test voltage V_X at the output (source of M₁), and find I_X. The gate node V₁ is connected to ground through R_S and to the source through C_GS, so\n\nV₁ = V_X · R_S C_GS s /(1 + R_S C_GS s),  V_GS = V₁ − V_X = −V_X /(1 + R_S C_GS s)\n\nThe current entering the output consists of the current through C_GS and the drain current −g_m V_GS:\n\nI_X = V_X (C_GS s + g_m)/(1 + R_S C_GS s)\n\n$$Z_{out}=\\frac{V_X}{I_X}=\\frac{1+R_S C_{GS}\\,s}{g_m+C_{GS}\\,s}$$\n\n**Why this is inductive**\n\n- At low frequency (s → 0): Z_out → 1/g_m. C_GS is open, the gate is held at ac ground through R_S, so any change in V_out fully changes V_GS, and the g_m action makes the source a low‑impedance node.\n- At high frequency (s → ∞): Z_out → R_S. C_GS becomes a short, the gate simply follows the source, V_GS can no longer change, so M₁ loses its ability to \"fight\" voltage changes at the output; what remains looking into the output is R_S (seen through the shorted C_GS).\n\nThus, if **R_S > 1/g_m**, the zero at 1/(R_S C_GS) occurs before the pole at g_m/C_GS and |Z_out| *rises* with frequency from 1/g_m to R_S — exactly what an inductor does. (If R_S < 1/g_m the impedance falls with frequency and is capacitive; if R_S = 1/g_m it is purely resistive.)\n\nPhysically: the g_m of M₁ is what makes the output impedance low, but the voltage that controls g_m (V_GS) is reduced at high frequency because R_S–C_GS lets the gate follow the source. The transistor's current therefore responds \"sluggishly\" to fast output voltage changes — current lags voltage, i.e., inductive behaviour.\n\nEquivalent circuit: Z_out can be modeled as R₁ = 1/g_m in series with the parallel combination of R₂ = R_S − 1/g_m and an inductor L = (C_GS/g_m)(R_S − 1/g_m). This inductive output impedance is why a source follower driven from a large R_S can ring (or even oscillate) when loaded by a capacitor, which resonates with the effective inductance.",
        "format": "markdown",
        "sha256": "16031c919ba8d161591fe07f4ba574ddba7ec12f98c661df5d8a412ca9f5ce5f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and derives the output impedance. It explains the transition from 1/gm at low frequency to RS at high frequency as CGS makes the gate follow the source, and correctly states that the impedance rises and is inductive when RS > 1/gm.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 3188,
        "total_tokens": 4908,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2229,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 3188,
        "total_tokens": 4908,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2229,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Circuit:** M1 is a source follower biased by the current source M2; the signal reaches the gate of M1 through the resistance R_S (e.g. the output resistance of the preceding stage). The output is taken at the source of M1. The key elements are R_S and the gate‑source capacitance C_GS of M1.\n\n**Small‑signal derivation**\n\nSet V_in to ac ground, apply a test voltage V_X at the output and find I_X (ignore r_O and body effect for simplicity; they only add parallel terms).\n\n- The gate is tied to ground through R_S and to the source through C_GS, so the gate voltage is a divided version of V_X:\n\n V_G = V_X · sR_S C_GS /(1 + sR_S C_GS),  V_GS = V_G − V_X = −V_X /(1 + sR_S C_GS)\n\n- Current entering the source node: the current through C_GS/R_S plus the current that the dependent source g_mV_GS draws:\n\n I_X = V_X·sC_GS/(1+sR_SC_GS) + g_mV_X/(1+sR_SC_GS)\n\n **Z_out = V_X/I_X = (1 + sR_S C_GS)/(g_m + sC_GS)**\n\n**Interpretation**\n\n- Low frequency (C_GS open): Z_out = 1/g_m – the usual source‑follower result.\n- High frequency (C_GS a short): the gate is tied to the source, V_GS can no longer change, the transistor's g_m current cannot respond, and the output \"sees\" only R_S: Z_out → R_S.\n- The expression has a zero at ω_z = 1/(R_S C_GS) and a pole at ω_p = g_m/C_GS. If **R_S > 1/g_m**, the zero comes first, |Z_out| rises from 1/g_m toward R_S and the phase of Z_out is positive between the zero and the pole – i.e. the impedance is inductive. (If R_S < 1/g_m the impedance falls with frequency and is capacitive.)\n\nThe impedance can be written as an equivalent network: a resistor 1/g_m in series with the parallel combination of a resistor (R_S − 1/g_m) and an inductor\n\n L = C_GS (R_S − 1/g_m)/g_m ,\n\nwhich is a real (positive) inductance precisely when R_S > 1/g_m.\n\n**Intuitive picture**\n\nApply a voltage step to the output. Initially C_GS couples the step directly to the gate, so V_GS does not change and M1's current does not change; the only current flows through R_S (small, V_X/R_S). As C_GS charges through R_S, the gate relaxes back to its bias value, V_GS changes by the full step and the current grows to g_mV_X. Current that starts small and builds up after a voltage is applied – current lagging voltage – is exactly inductive behavior. The gate being \"bootstrapped\" by C_GS at high frequency spoils the low 1/g_m output impedance of the follower.\n\n**Consequence:** together with the capacitance present at the output node (C_SB1, C_DB2, C_GD2, load), this inductive output impedance forms a resonant circuit and can produce peaking or ringing in the follower's response; the same effect is sometimes deliberately exploited to realize \"active inductors.\"",
        "format": "markdown",
        "sha256": "5d39a06808a22830e09086de563ba26280c3c535c02ae55ff695c9d0aca8fea4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and derives the output impedance. It explains the low-frequency 1/gm to high-frequency RS transition as C_GS coupling the gate to the source, and correctly states that the impedance is inductive when RS > 1/gm.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 4487,
        "total_tokens": 6207,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 4487,
        "total_tokens": 6207,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the problem**\n\nM₁ is a source follower biased by the current source M₂; R_S is the resistance of the signal source driving the gate. For the output impedance we ground V_in, apply a test voltage V_X at the output (source of M₁), and keep the one capacitance that matters: C_GS of M₁, which sits between the output node and the gate node. (r_o1, r_o2, 1/g_mb and the capacitances of M₂ simply appear in parallel with the output and do not change the argument.)\n\n**Derivation**\n\nThe gate node is connected to ac ground only through R_S, so C_GS and R_S form a divider between the output and ground:\n\n- V_G = V_X · (sR_S C_GS)/(1 + sR_S C_GS)\n- V_GS = V_G – V_X = –V_X /(1 + sR_S C_GS)\n\nKCL at the source node (current through C_GS plus the transconductance current):\n\nI_X = (V_X – V_G)·sC_GS – g_m V_GS = V_X (g_m + sC_GS)/(1 + sR_S C_GS)\n\nso\n\n  Z_out = (1 + sR_S C_GS)/(g_m + sC_GS)\n\n**Why this is inductive**\n\n- At low frequency (C_GS open): Z_out → 1/g_m – the usual follower output resistance.\n- At high frequency (C_GS short, gate tied to source): Z_out → R_S.\n- Zero at ω_z = 1/(R_S C_GS), pole at ω_p = g_m/C_GS.\n\nIf R_S > 1/g_m, the zero comes before the pole, so |Z_out| *rises* with frequency from 1/g_m to R_S, and the phase of Z_out is positive (current lags voltage) in between. An impedance that increases with frequency with a positive phase is, by definition, inductive. (If R_S < 1/g_m the impedance falls with frequency and looks capacitive; if R_S = 1/g_m it is purely resistive.)\n\nIn fact, Z_out can be modelled exactly as\n\n  Z_out = 1/g_m  in series with  [ (R_S – 1/g_m) ∥ L ],  L = (C_GS/g_m)(R_S – 1/g_m),\n\nwhich is a real inductor only when R_S > 1/g_m.\n\n**Physical intuition**\n\nThe follower's low output impedance (1/g_m) comes from the transistor's transconductance opposing any change at the source: if V_out is pushed down, V_GS increases and I_D rises to counteract it. This \"feedback\" works only if the gate stays put. At higher frequencies C_GS couples the source movement back to the gate, and because the gate is tied to ground only through a large R_S, the gate cannot be held fixed—it starts to follow the source. The change in V_GS shrinks, the g_m current that was lowering the output impedance fades, and the test source instead sees R_S through C_GS. Thus the impedance climbs with frequency, exactly what an inductor does.\n\n**Consequence**\n\nTogether with the capacitance at the output (C_SB1, C_DB2, C_GD2, load), this inductive Z_out forms a resonant network, so a source follower driven from a high-impedance source can show peaking in its frequency response and ringing in its step response (the same effect is sometimes exploited deliberately as an \"active inductor\").",
        "format": "markdown",
        "sha256": "0dc68dd32bb3a86875cbd971b1addc4bf2f31ff36404681e15772f8b147ab8fe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and derives the output impedance, including the low-frequency 1/gm and high-frequency RS limits. It explains that C_GS couples the gate to the source and that the impedance rises with frequency—and is inductive—when RS > 1/gm, matching the full-credit rule.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 4846,
        "total_tokens": 6566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3741,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1720,
        "output_tokens": 4846,
        "total_tokens": 6566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3741,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n| Element | Role |\n|---|---|\n| $I_{in}$ → node X | Input is a **current**, injected into the gate of M₁ |\n| M₁ + R_D1 | Forward amplifier: a common‑source stage, $v_{out}=-g_{m1}R_{D1}\\,v_X$ (inverting) |\n| M₂ (gate at $V_{out}$, drain at X, source grounded) | Feedback network: it **senses the output voltage** (gate in parallel with the output) and **returns a current** $I_F = g_{m2}V_{out}$ that is subtracted at node X (drain in parallel with the input) |\n\nSo the sense/return mechanism is **voltage‑sensing, current‑return → voltage‑current (shunt‑shunt) feedback**, i.e. a trans‑impedance configuration with feedback factor $\\beta = I_F/V_{out}=g_{m2}$ (A/V).\n\nNotice also that M₁'s gate is tied to M₂'s drain and M₂'s gate is tied to M₁'s drain – the devices are **cross‑coupled**, which already hints at the result below.\n\n## 2. Polarity of the feedback\n\nPerturb the input and follow the loop:\n\n$I_{in}\\uparrow \\;\\Rightarrow\\; V_X\\uparrow \\;\\Rightarrow\\; V_{out}\\downarrow$ (M₁ inverts) $\\;\\Rightarrow\\; V_{GS2}\\downarrow \\;\\Rightarrow\\; I_{D2}\\downarrow$\n\nM₂ now pulls **less** current out of node X, so even more of $I_{in}$ is available to charge X and $V_X$ rises further. The returned signal *reinforces* the disturbance → **positive feedback**.\n\nLoop gain (break at the high‑impedance gate of M₂, apply $v_t$):\n\n$$\ni_{d2}=g_{m2}v_t,\\qquad v_X=-g_{m2}v_t\\,(r_{o2}\\,\\|\\,R_{S}),\\qquad\nv_{out}=-g_{m1}R_{D1}v_X=+\\,g_{m1}g_{m2}R_{D1}(r_{o2}\\|R_S)\\,v_t\n$$\n\n$T=+g_{m1}g_{m2}R_{D1}(r_{o2}\\|R_S)\\gg 1$ (→ ∞ for an ideal source and λ = 0). The loop contains two inverting stages (M₁ and M₂ both act as common‑source inverters), hence an even number of inversions and a positive loop gain.\n\n## 3. Formal small‑signal \"closed‑loop\" results (λ = γ = 0)\n\nKCL at X (gate of M₁ draws no current): $i_{in}=g_{m2}v_{out}$, and $v_{out}=-g_{m1}R_{D1}v_X$, giving\n\n$$\n\\frac{v_{out}}{i_{in}}=\\frac{1}{g_{m2}},\\qquad \n\\frac{v_X}{i_{in}}=-\\frac{1}{g_{m1}g_{m2}R_{D1}}\n$$\n\nThe same thing in feedback form, with finite $r_{o2}$:\n\n$$\nR_{closed}=\\frac{R_0}{1-T}=\\frac{-g_{m1}R_{D1}r_{o2}}{1-g_{m1}g_{m2}R_{D1}r_{o2}}\\;\\to\\;+\\frac1{g_{m2}},\\qquad\nR_{in}=\\frac{r_{o2}}{1-T}\\approx-\\frac{1}{g_{m1}g_{m2}R_{D1}},\\qquad\nR_{out}=\\frac{R_{D1}}{1-T}\\approx-\\frac{1}{g_{m1}g_{m2}r_{o2}}\n$$\n\nThe denominator is $1-T$ (not $1+T$), the apparent transimpedance has the \"wrong\" (non‑inverting) sign, and both port resistances are **negative** – all signatures of positive feedback with $|T|>1$. Including the capacitance $C_X$ at node X:\n\n$$\n\\frac{v_{out}}{i_{in}}=\\frac{1}{g_{m2}-sC_X/(g_{m1}R_{D1})}\\quad\\Rightarrow\\quad\\text{pole at } s=+\\frac{g_{m1}g_{m2}R_{D1}}{C_X}\n$$\n\na right‑half‑plane pole: the algebraic operating point exists but is unstable.\n\n## 4. What the circuit actually does (DC)\n\nThe nominal bias point ($I_{D2}=I_{in}$ ⇒ $V_{out}=V_{TH}+\\sqrt{2I_{in}/(\\mu_nC_{ox}(W/L)_2)}$, $I_{D1}=(V_{DD}-V_{out})/R_{D1}$) is metastable. Any noise drives the circuit regeneratively into one of two latched states:\n\n* $V_X$ low (M₁ off) → $V_{out}=V_{DD}$ → M₂ in deep triode sinking $I_{in}$ with $V_X\\approx I_{in}R_{on2}<V_{TH}$ – self‑consistent and stable;\n* $V_X$ high (M₁ hard on) → $V_{out}$ low → M₂ off → $I_{in}$ has no path and X rises to the compliance limit of the source.\n\nSo, as drawn, this is a **bistable/regenerative (latch‑like) circuit, not a linear transimpedance amplifier**.\n\n## 5. Making it a true negative‑feedback TIA\n\nThe forward path must be non‑inverting (M₂, like any CS transconductor, inverts). The standard fix is to inject $I_{in}$ into the **source** of M₁ (common‑gate M₁ with a gate bias $V_b$). Then\n\n$$\nR_0=R_{D1},\\;\\; R_{in,open}=\\frac{1}{g_{m1}},\\;\\; T=g_{m2}R_{D1}\n$$\n$$\n\\frac{V_{out}}{I_{in}}=\\frac{R_{D1}}{1+g_{m2}R_{D1}}\\approx\\frac{1}{g_{m2}},\\qquad\nR_{in}=\\frac{1/g_{m1}}{1+g_{m2}R_{D1}},\\qquad\nR_{out}=\\frac{R_{D1}}{1+g_{m2}R_{D1}}\n$$\n\n– a proper voltage‑current feedback amplifier with low input and output impedances. Alternatives: replace M₂ by a feedback resistor $R_F$ from $V_{out}$ to X (classic TIA, gain ≈ $-R_F$), or add one more inverting stage in the forward path.\n\n**Summary:** voltage‑current (shunt‑shunt) feedback topology with $\\beta=g_{m2}$, but because M₁ (CS) and M₂ both invert, the loop gain $g_{m1}g_{m2}R_{D1}r_{o2}$ is positive → positive feedback, unstable/latching; the naïve result $V_{out}/I_{in}=1/g_{m2}$ is only the (unstable) algebraic solution.",
        "format": "markdown",
        "sha256": "6f004873b3977123dac09cbc36cb2e60f9e0731d7409ca0bea8f05e831e96feb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate connection to Vout, the positive-feedback loop, and the resulting negative input resistance and unstable/latching behavior. This meets the golden solution’s full-credit rule.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 25847,
        "total_tokens": 28057,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23404,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 25847,
        "total_tokens": 28057,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23404,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\n- $M_1$ with $R_{D1}$ is a common‑source gain stage. Its input is node X, which is driven by the *current* $I_{in}$; its output is the voltage $V_{out}$.  \n- $M_2$ is the feedback element: its gate is tied to $V_{out}$ (it *senses the output voltage*, in parallel, drawing no current) and its drain current $I_{D2}=g_{m2}V_{out}$ is pulled out of node X, where it is *subtracted from the input current* (current return / shunt mixing).\n\nSo topologically this is a voltage–current (shunt–shunt) feedback loop around a transimpedance amplifier, with feedback factor \n\n$$K=\\frac{I_F}{V_{out}}=g_{m2}\\quad(\\text{units of }1/\\Omega).$$\n\n**Polarity of the feedback (the key point)**\n\nFollow a disturbance around the loop:\n\n$I_{in}\\uparrow \\;\\Rightarrow\\; V_X\\uparrow \\;\\Rightarrow\\; I_{D1}\\uparrow \\;\\Rightarrow\\; V_{out}\\downarrow \\;\\Rightarrow\\; V_{GS2}\\downarrow \\;\\Rightarrow\\; I_{D2}\\downarrow$\n\nSince $I_{D2}$ is the current *removed* from node X, a smaller $I_{D2}$ leaves more net current to charge X, so $V_X$ rises **further**. The returned signal reinforces the original change: the feedback is **positive**.\n\n**Small‑signal confirmation** ($\\lambda=0$)\n\nForward path: $v_{out}=-g_{m1}R_{D1}\\,v_X$. Return path: $i_{D2}=g_{m2}v_{out}$. KCL at X (gate of $M_1$ draws no current):\n\n$$i_{in}=g_{m2}v_{out}\\;\\Rightarrow\\;\\frac{v_{out}}{i_{in}}=\\frac{1}{g_{m2}},\\qquad \n\\frac{v_X}{i_{in}}=-\\frac{1}{g_{m1}g_{m2}R_{D1}}$$\n\nThe transimpedance looks like a nice \"$1/K$\" result, but the closed‑loop input resistance at X is **negative** – the signature of positive feedback. Writing it in feedback form with a finite resistance $R_X$ at node X (e.g. $r_{O2}$):\n\n$$A_O=\\frac{v_{out}}{i_{in}}\\Big|_{open}=-g_{m1}R_{D1}R_X,\\qquad KA_O=-g_{m1}g_{m2}R_{D1}R_X<0,$$\n\n$$\\frac{v_{out}}{i_{in}}=\\frac{A_O}{1+KA_O}=\\frac{-g_{m1}R_{D1}R_X}{1-g_{m1}g_{m2}R_{D1}R_X},\\qquad R_{in}=\\frac{R_X}{1+KA_O},\\;R_{out}=\\frac{R_{D1}}{1+KA_O}$$\n\nThe loop gain is negative (the returned voltage at $M_2$'s gate is in phase with the injected one), so $1+KA_O<1$ and in fact $<0$ for any appreciable gain.\n\n**Consequence – it is a latch, not an amplifier**\n\nIncluding the capacitance $C_X$ at node X gives a pole at \n\n$$s_p=+\\frac{g_{m1}g_{m2}R_{D1}-1/R_X}{C_X}>0 ,$$\n\ni.e., in the right half‑plane. The operating point where $I_{D2}=I_{in}$ (with $V_{out}=V_{GS2}$ and $V_X=V_{GS1}$) exists but is unstable; the circuit regenerates to one of two states:\n- $V_X\\approx 0$: $M_1$ off, $V_{out}=V_{DD}$, $M_2$ in triode sinking all of $I_{in}$; or  \n- $V_X$ high: $M_1$ hard on, $V_{out}\\approx 0$, $M_2$ off, and $I_{in}$ drives node X up to the current source's compliance limit.\n\n**How to obtain negative feedback**\n\nWith an inverting CS stage, a grounded‑source transconductor from $V_{out}$ to X cannot give negative feedback (an NMOS or a PMOS $M_2$ both end up positive). One must either (a) replace $M_2$ by a resistor $R_F$ from $V_{out}$ to X, where $i_F=(v_X-v_{out})/R_F$ increases when $V_{out}$ falls (the standard TIA, $v_{out}/i_{in}\\approx -R_F$); (b) make $M_1$ a common‑gate device with $I_{in}$ entering its source, so $V_X\\uparrow\\Rightarrow V_{out}\\uparrow\\Rightarrow I_{D2}\\uparrow$ pulls X back down (then $v_{out}/i_{in}\\approx 1/g_{m2}$ with a stable loop); or (c) add one more inversion between $V_{out}$ and the gate of $M_2$.",
        "format": "markdown",
        "sha256": "92a884ca35eb4ecddb698d8809efe8610fcccf512b99ec3eea6ed789896dd80f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that M2’s gate is tied to Vout, recognizes the positive-feedback loop, and explains its negative input resistance and unstable, latching behavior.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 28628,
        "total_tokens": 30838,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26877,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 28628,
        "total_tokens": 30838,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26877,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## What the circuit is\n\n- **M1** is a common‑source (CS) amplifier: gate at node X, source grounded, drain load R_D1, output V_out.\n- **M2** is a second CS device whose **gate senses V_out** and whose **drain is tied back to the input node X**.\n- The input is a **current** (I_in into node X), the output is a **voltage** (V_out).\n\nSo M1 is the forward amplifier (current in at X → voltage out), and M2 is the feedback element: it senses the output *voltage* (gate in shunt with the output, draws no current → ideal voltage sensing) and returns a *current* I_D2 to the input node (in shunt with the input). This is a **voltage–current (shunt–shunt) feedback topology**, i.e. a transimpedance configuration whose closed‑loop quantity would be V_out/I_in.\n\n## DC operating point (if it existed)\n\nThe gate of M1 draws no current, so KCL at X forces\n\n  I_D2 = I_in  ⇒ V_out = V_GS2 = V_TH + √(2I_in /(μ_nC_ox(W/L)_2))\n\n  I_D1 = (V_DD − V_GS2)/R_D1  ⇒ V_X = V_GS1 = V_TH + √(2I_D1 /(μ_nC_ox(W/L)_1))\n\n## Polarity of the feedback\n\nPerturb the input and follow it around the loop:\n\n1. I_in ↑ → node X is a high‑impedance node (M1's gate and r_O2 only), so the extra current charges it and **V_X ↑**.\n2. V_X ↑ → I_D1 ↑ → **V_out ↓** (M1 is inverting).\n3. V_out ↓ → V_GS2 ↓ → **I_D2 ↓**: M2 pulls *less* current out of X.\n4. Less current removed from X → even more of I_in accumulates at X → **V_X rises further**.\n\nThe returned signal *reinforces* the original change: the loop consists of two inverting CS stages (M1: X→V_out, M2: V_out→X), so the net loop phase shift is 0°. **The feedback is positive.**\n\n## Loop gain\n\nBreak the loop at the gate of M2 (ideal breaking point, no loading) and inject v_t:\n\n  i_d2 = g_m2 v_t → v_X = −g_m2 r_O2 v_t → v_out = −g_m1(R_D1‖r_O1) v_X = **+ g_m1 g_m2 r_O2 (R_D1‖r_O1) · v_t**\n\nThe returned signal is in phase with the test signal with magnitude\n  T = g_m1 g_m2 r_O2 (R_D1‖r_O1) ≫ 1 (→ ∞ if channel‑length modulation is neglected).\n\nEquivalently, with the forward transimpedance R_0 = v_out/i_err = −g_m1(R_D1‖r_O1)r_O2 and feedback factor K = i_D2/v_out = g_m2, the loop gain K·R_0 is negative — positive feedback.\n\n## Consequence: the circuit is unstable\n\nAdd the node capacitance C_X at X. KCL at X with v_out = −g_m1(R_D1‖r_O1)v_X gives\n\n  v_X / i_in = 1 / [ sC_X + 1/r_O2 − g_m1 g_m2 (R_D1‖r_O1) ]\n\nThe pole sits at s = [g_m1g_m2(R_D1‖r_O1) − 1/r_O2]/C_X > 0, i.e. in the right half‑plane. The algebraic \"closed‑loop transimpedance\" one would compute, V_out/I_in ≈ 1/g_m2, is therefore meaningless: any disturbance grows exponentially and the circuit latches into one of two end states:\n- V_X collapses → M1 off, V_out = V_DD, M2 in triode sinking I_in with V_X ≈ 0; or\n- V_X runs up → V_out drops below V_TH, M2 turns off, I_in has no path and drives V_X to the compliance limit of the current source (M1 in triode).\n\n## Summary / fix\n\nAs drawn, the circuit is a shunt–shunt (voltage‑sense, current‑return) loop with **positive** feedback and loop gain well above unity — it is not a usable amplifier. Negative feedback requires a non‑inverting return path, e.g. use M2 as a source follower (gate at V_out, source at X, drain at V_DD), replace M2 by a resistor R_F from V_out to X (classic TIA, V_out/I_in ≈ −R_F), or add one more inverting stage inside the loop.",
        "format": "markdown",
        "sha256": "19e599cd11b743fea30baa32ab03163dcfddf043750e9bef5419f3a96ffb9038"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate as tied to Vout, traces the positive-feedback loop, and explains the resulting negative input conductance, instability, and latching. Minor modeling or terminology imprecision does not affect the essential answer.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 15025,
        "total_tokens": 17235,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13462,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2210,
        "output_tokens": 15025,
        "total_tokens": 17235,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13462,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n| Element | Role |\n|---|---|\n| **M1** (gate at V_b, input at its source, load R_D1) | Common‑gate stage – converts the input current into a voltage at node X |\n| **M2** (gate at X, load R_D2) | Common‑source stage – voltage gain –g_m2·R_D2, inverts |\n| **R_F** (V_out → source of M1) | Feedback element |\n| **I_in** | Input current source |\n\nCurrent in, voltage out → the circuit is a **transimpedance amplifier (TIA)**.\n\n**Feedback type:** R_F is connected *in parallel* with the output (it senses V_out) and *in parallel* with the input node (it returns a current i_RF that adds to/subtracts from I_in). This is **voltage–current (shunt–shunt) feedback**. Consequences: the transimpedance, the input impedance and the output impedance are all divided by (1 + loop gain).\n\n**Polarity check:**\nI_in ↑ → V_P (source of M1) ↑ → V_GS1 ↓ → I_D1 ↓ → V_X ↑ → I_D2 ↑ → V_out ↓.\nWith V_out falling, R_F pulls current *out of* the input node (i_RF as drawn becomes negative), so less of I_in reaches M1 – the feedback opposes the disturbance → **negative feedback**. The summing node is the source of M1: error current = I_in + i_RF.\n\n## 2. Open‑loop amplifier with loading (λ = 0, body effect neglected)\n\nBreaking a shunt–shunt loop: R_F appears to ground at the input **and** at the output.\n\n- Input node: R_F ‖ (1/g_m1). The part of I_in entering M1's source:\n i_1 = I_in · R_F/(R_F + 1/g_m1)\n- This current flows through R_D1 (raising V_X):  v_X = i_1·R_D1\n- M2 drives R_D2 ‖ R_F:  v_out = –g_m2 (R_D2‖R_F) v_X\n\nOpen‑loop transimpedance:\n\n  A_O = v_out/I_in |open = – g_m2 R_D1 (R_D2‖R_F) · R_F/(R_F + 1/g_m1)\n\nFeedback factor (current returned per unit output voltage): K = i_RF/v_out = 1/R_F\n\nLoop gain:\n\n  T = K·|A_O| = g_m2 R_D1 (R_D2‖R_F) / (R_F + 1/g_m1)\n\n## 3. Closed‑loop results\n\nLet G ≡ g_m2 R_D1 (R_D2‖R_F).\n\n**Transimpedance**\n\n  v_out/I_in = A_O/(1+T) = – G·R_F / (R_F + 1/g_m1 + G)  → **≈ –R_F** for T ≫ 1\n\n(Intuition: the input node becomes a virtual ground, essentially all of I_in is forced through R_F, so V_out ≈ –I_in·R_F; gain is set by a resistor, not by g_m or R_D.)\n\n**Input impedance**\n\n  R_in = [R_F ‖ (1/g_m1)]/(1+T) = (R_F/g_m1)/(R_F + 1/g_m1 + G)  ≈ R_F/(g_m1 G)\n\nAlready low (1/g_m1) because of the CG stage, and reduced further by the loop – ideal for a current‑source input (e.g., photodiode).\n\n**Output impedance**\n\n  R_out = (R_D2‖R_F)/(1+T) = (R_D2‖R_F)(R_F + 1/g_m1)/(R_F + 1/g_m1 + G)\n\n## 4. Check by direct nodal analysis\n\nKCL at the input node P, X and the output (v_X = g_m1 R_D1 v_P):\n\n  I_in = (g_m1 + 1/R_F) v_P – v_out/R_F\n  –v_out(1/R_D2 + 1/R_F) = (g_m1 g_m2 R_D1 – 1/R_F) v_P\n\nNeglecting the small feed‑forward term 1/R_F against g_m1 g_m2 R_D1 gives exactly\n\n  v_out/I_in = – g_m2 R_D1 (R_D2‖R_F) R_F / (R_F + 1/g_m1 + g_m2 R_D1 (R_D2‖R_F)),\n\nconfirming the feedback result.\n\n## 5. Remarks\n\n- Signs: the TIA is inverting; the figure's i_RF (drawn from V_out toward the input) is the current that is *subtracted* from I_in at the summing node.\n- R_F also provides DC feedback: the loop forces V_out to the value for which (V_out – V_P)/R_F plus the DC input current equals I_D1, stabilizing the bias of both transistors.\n- If body effect or channel‑length modulation are included, replace g_m1 → g_m1 + g_mb1 and R_D1, R_D2 → R_D1‖r_o1, R_D2‖r_o2.",
        "format": "markdown",
        "sha256": "62965e6ef3bef056db341a99485a8ef5d1569cb58576b7ac1d3c36ab0c1dccbe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from Vout to the input node forming a transimpedance amplifier.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 20905,
        "total_tokens": 23422,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19199,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 20905,
        "total_tokens": 23422,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19199,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\n- **M₁** – gate held at the constant bias V_b, signal current injected at the source, output taken at the drain (node X): a **common‑gate stage**. It converts the input current into a voltage at X (input resistance ≈ 1/g_m1).\n- **M₂** – a **common‑source stage** that amplifies V_X with gain −g_m2·(load).\n- **R_F** – connected from the output node to the input node. It is in *parallel* with the output (it senses V_out) and in *parallel* with the input current source (it returns a *current* i_RF). \n\nHence this is **voltage–current (shunt–shunt) feedback** around a two‑stage amplifier, i.e. a **transimpedance amplifier**: input quantity I_in, output quantity V_out, feedback factor \n\nK = i_RF / V_out = 1/R_F.\n\n(Assume all devices in saturation and λ = 0; I_in denotes the signal current.)\n\n**Polarity of the feedback**\n\nLet I_in increase (more current pushed into the source node of M₁):\n\nsource voltage of M₁ ↑ → V_GS1 ↓ → I_D1 ↓ → V_X = V_DD − I_D1R_D1 ↑ → I_D2 ↑ → V_out ↓.\n\nWith V_out falling, the current i_RF = (V_out − V_in)/R_F flowing from the output into the input node *decreases* (R_F now pulls current away from the input node toward the falling output). The current that actually reaches M₁, I_in + i_RF, therefore rises by less than ΔI_in — the feedback opposes the change: **negative feedback**.\n\n**Open‑loop amplifier (with loading by R_F)**\n\nFor shunt–shunt feedback the feedback resistor appears as R_F‑to‑ground at both ports:\n\n- Input: v_in = i_in (R_F ∥ 1/g_m1); current pulled up through M₁: g_m1 v_in \n- v_X = g_m1 R_D1 (R_F ∥ 1/g_m1) i_in \n- v_out = −g_m2 (R_D2 ∥ R_F) v_X\n\n$$\nR_O=\\frac{v_{out}}{i_{in}}\\Big|_{open}=-g_{m1}R_{D1}\\,g_{m2}(R_{D2}\\|R_F)\\left(R_F\\Big\\|\\frac1{g_{m1}}\\right)\n=-\\frac{g_{m1}g_{m2}R_{D1}(R_{D2}\\|R_F)\\,R_F}{1+g_{m1}R_F}\n$$\n\nR_in,open = R_F ∥ 1/g_m1,  R_out,open = R_D2 ∥ R_F.\n\n**Loop gain** (define A ≡ g_m1 g_m2 R_D1 (R_D2∥R_F)):\n\n$$T=K|R_O|=\\frac{|R_O|}{R_F}=\\frac{A}{1+g_{m1}R_F}$$\n\n**Closed‑loop results**\n\n$$\n\\frac{v_{out}}{i_{in}}=\\frac{R_O}{1+T}\n=-\\,\\frac{g_{m1}g_{m2}R_{D1}(R_{D2}\\|R_F)\\,R_F}{1+g_{m1}R_F+g_{m1}g_{m2}R_{D1}(R_{D2}\\|R_F)}\n\\;\\xrightarrow{T\\gg1}\\;-R_F\n$$\n\n$$\nR_{in}=\\frac{R_F\\|1/g_{m1}}{1+T}=\\frac{R_F}{1+g_{m1}R_F+A}\\qquad(\\ll 1/g_{m1})\n$$\n\n$$\nR_{out}=\\frac{R_{D2}\\|R_F}{1+T}=\\frac{(R_{D2}\\|R_F)(1+g_{m1}R_F)}{1+g_{m1}R_F+A}\\qquad(<R_{D2}\\|R_F)\n$$\n\n**Interpretation / checks**\n\n- For large loop gain the input node becomes a virtual ground, all of i_in must flow through R_F, and v_out ≈ −R_F i_in: the transimpedance is set by R_F alone, independent of g_m and R_D.\n- The feedback lowers the input resistance (good for a current input) and the output resistance (good for a voltage output) by (1+T).\n- Limits: R_F → ∞ gives v_out/i_in → −g_m2 R_D1 R_D2, R_in → 1/g_m1, R_out → R_D2, as expected for the plain CG–CS cascade.\n- A direct nodal analysis gives exactly the same expressions with A replaced by (g_m1g_m2R_D1 − 1/R_F)(R_D2∥R_F); the small −1/R_F term is the feed‑forward through R_F, negligible when g_m1g_m2R_D1 ≫ 1/R_F, which justifies the feedback approximation.",
        "format": "markdown",
        "sha256": "644447a5f6b70e360ee4fbc75d607e0341174b7461751be7be2461c15031f9c5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as output-to-input feedback forming a transimpedance amplifier. It also correctly describes negative feedback and the high-loop-gain −RF behavior, meeting the golden full-credit rule.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 21097,
        "total_tokens": 23614,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19424,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 21097,
        "total_tokens": 23614,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19424,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\n- **M₁** is a common‑gate stage (gate at the ac ground V_b): the input current I_in enters its source, and the current that flows through M₁ develops a voltage at X across R_D1 (no inversion: more current into the source → V_P rises → V_GS1 falls → I_D1 falls → V_X rises).\n- **M₂** is a common‑source stage (inverting) with load R_D2.\n- **R_F** is connected between the output node and the input (summing) node. It *senses the output voltage* (parallel connection at the output) and *returns a current* to the input node (parallel connection at the input).\n\nHence this is a **voltage–current (shunt–shunt) feedback** amplifier – a **transimpedance amplifier (TIA)** whose closed‑loop gain is V_out/I_in.\n\n**Sign of the feedback**\n\nI_in ↑ → V_P ↑ → V_X ↑ (CG stage) → V_out ↓ (CS stage) → current through R_F is pulled *out* of the input node, i.e. i_RF (defined in the figure from V_out toward the input) becomes negative and opposes I_in. The feedback is **negative**.\n\n**Open‑loop (loaded) amplifier** (λ = γ = 0, I_in an ideal current source)\n\nFor shunt–shunt feedback the feedback network (R_F) loads both ports with R_F to ground:\n\n- Input node: I_in flows into R_F ∥ (1/g_m1):  v_P = I_in·R_F/(1 + g_m1R_F)\n- Current through M₁ = g_m1 v_P, so  v_X = g_m1R_D1 v_P\n- Output: v_out = −g_m2 (R_D2 ∥ R_F) v_X\n\nOpen‑loop transimpedance:\n\nR_O = v_out/I_in |open = −g_m1g_m2 R_D1 (R_D2∥R_F) · R_F/(1 + g_m1R_F)\n    ≈ −g_m2 R_D1 (R_D2∥R_F)  for g_m1R_F ≫ 1\n\nOpen‑loop impedances: R_in,open = R_F ∥ 1/g_m1 = R_F/(1+g_m1R_F),  R_out,open = R_D2 ∥ R_F\n\nFeedback factor: K = 1/R_F (current returned per volt of output).\n\n**Loop gain**\n\nT = |R_O|·K = g_m1g_m2 R_D1 (R_D2∥R_F) / (1 + g_m1R_F)\n\n(Breaking the loop at the gate of M₂ gives the same result, with R_F replaced by R_F + 1/g_m1 in the parallel combination – negligible difference.)\n\n**Closed‑loop results**\n\nTransimpedance:\n\nV_out/I_in = R_O/(1+T) = − g_m1g_m2 R_D1 (R_D2∥R_F) R_F / [1 + g_m1R_F + g_m1g_m2 R_D1 (R_D2∥R_F)]  → −R_F for T ≫ 1\n\nInput impedance (reduced by 1+T, below the already low 1/g_m1 of the CG stage):\n\nR_in = R_in,open/(1+T) = R_F / [1 + g_m1R_F + g_m1g_m2 R_D1 (R_D2∥R_F)]\n\nOutput impedance (also reduced by 1+T):\n\nR_out = R_out,open/(1+T) = (R_D2∥R_F)(1 + g_m1R_F) / [1 + g_m1R_F + g_m1g_m2 R_D1 (R_D2∥R_F)]\n\n**Check by direct nodal analysis**\n\nWriting KCL at P, X and the output gives exactly\n\nV_out/I_in = (R_D2∥R_F)(1 − g_m1g_m2R_D1R_F) / [1 + g_m1R_F − R_D2/(R_D2+R_F) + g_m1g_m2R_D1(R_D2∥R_F)],\n\nR_out = R_D2 ∥ [(1+g_m1R_F)/(g_m1(1+g_m2R_D1))].\n\nThe only differences from the feedback results are the forward feed‑through term \"1\" in the numerator and the small term R_D2/(R_D2+R_F) ≈ 1/R_F vs 1/(R_F+1/g_m1) – negligible when the loop gain is large, confirming the analysis.\n\n**Interpretation**\n\n- The CG+CS pair acts as a high‑gain inverting \"transimpedance op‑amp\"; R_F closes the loop so that V_out ≈ −R_F·I_in. Almost all of I_in actually flows through R_F (i_RF ≈ −I_in) because the input node is driven toward a virtual ground (R_in ≈ (1/g_m1)/(1+T)).\n- Both input and output impedances are lowered by (1+T) – the expected behavior of shunt–shunt feedback, and desirable for a TIA (low input impedance pushes the pole formed with the source/photodiode capacitance to high frequency).\n- Trade‑off: larger R_F raises the closed‑loop gain but also loads M₂'s output (R_D2∥R_F) and lowers the loop gain/bandwidth. Body effect and channel‑length modulation can be included by replacing g_m1 with g_m1 + g_mb1 and placing r_O1, r_O2 in parallel with R_D1, R_D2 respectively.",
        "format": "markdown",
        "sha256": "1cf839254205298cb4f37cb315730186774e0e8fb599e0667ab51b974db4be6b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as feedback from the output to the input, forming a negative-feedback transimpedance amplifier. This meets the golden solution’s full-credit rule.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 16802,
        "total_tokens": 19319,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14965,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2517,
        "output_tokens": 16802,
        "total_tokens": 19319,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14965,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n| Element | Role |\n|---|---|\n| $M_1$ (NMOS, gate at fixed $V_b$) | Common‑gate (CG) amplifier: input at its source (node X), output at its drain |\n| $I_1$ | Ideal current‑source load of the CG stage (sets $I_{D1}=I_1$) |\n| $M_2$ (PMOS, source at $V_{DD}$, gate on $V_{out}$, drain on X) | Feedback element: senses $V_{out}$ and returns a current $g_{m2}v_{out}$ to the input node |\n| $I_{in}$ | Signal (current) source |\n| lower current source (call it $I_2$) | Bias: carries $M_2$'s bias current |\n\nSo the circuit is a **transimpedance amplifier** (current in → voltage out): a CG stage closed in a **voltage–current (shunt–shunt) feedback** loop through $M_2$.\n\n**DC operating point:** the gate of $M_2$ draws no current, so $I_{D1}=I_1$ and $I_{D2}=I_1+I_2$ (minus any dc part of $I_{in}$). Hence $V_X=V_b-V_{GS1}$ and $V_{out}=V_{DD}-|V_{GS2}|$. For saturation: $V_{out}>V_b-V_{TH1}$ ($M_1$), $V_X<V_{DD}-|V_{OV2}|$ ($M_2$), and $V_X$ must leave headroom for $I_2$. $I_2$ lets $I_{D2}$ (and thus $g_{m2}$) be chosen independently of $I_1$.\n\n**Polarity:** $I_{in}\\uparrow \\Rightarrow V_X\\uparrow \\Rightarrow V_{GS1}\\downarrow \\Rightarrow I_{D1}\\downarrow$; since $I_1$ is fixed, $V_{out}\\uparrow \\Rightarrow V_{SG2}\\downarrow \\Rightarrow I_{D2}\\downarrow$, i.e. less current is injected into X and $V_X$ is pulled back → **negative feedback**.\n\n## 2. Direct small‑signal analysis\n\n(Body effect of $M_1$: replace $g_{m1}\\to g_{m1}+g_{mb1}$; $M_2$ has none.)\n\nKCL at the output node (ideal $I_1$ and the gate of $M_2$ carry no signal current, so the current through $M_1$ is zero):\n\n$$g_{m1}v_X+\\frac{v_X-v_{out}}{r_{o1}}=0\\;\\Rightarrow\\; v_{out}=(1+g_{m1}r_{o1})\\,v_X$$\n\nKCL at node X:\n\n$$I_{in}=g_{m2}v_{out}+\\frac{v_X}{r_{o2}}\n\\;\\Rightarrow\\;\n\\boxed{\\frac{V_{out}}{I_{in}}=\\frac{1}{g_{m2}+\\dfrac{1}{r_{o2}(1+g_{m1}r_{o1})}}\n=\\frac{r_{o2}(1+g_{m1}r_{o1})}{1+g_{m2}r_{o2}(1+g_{m1}r_{o1})}\\approx\\frac{1}{g_{m2}}}$$\n\n## 3. Feedback‑method view\n\nOpen the loop, keeping the loading of $M_2$: it loads the input node with $r_{o2}$ (drain of $M_2$, gate grounded) and the output with an open circuit (gate).\n\n- Open‑loop transimpedance: all of $i_{in}$ flows in $r_{o2}$ (the CG stage with an infinite load has infinite source impedance), and the CG gain into an infinite load is $1+g_{m1}r_{o1}$:\n $R_0 = r_{o2}(1+g_{m1}r_{o1})$\n- Feedback factor (current returned per volt of output): $\\beta=g_{m2}$\n- Loop gain: $T=\\beta R_0 = g_{m2}r_{o2}(1+g_{m1}r_{o1})\\approx (g_{m1}r_{o1})(g_{m2}r_{o2})$ — the product of two intrinsic gains, very large.\n- Open‑loop impedances: $R_{in,open}=r_{o2}$; $R_{out,open}=r_{o1}+r_{o2}+g_{m1}r_{o1}r_{o2}$ (drain of $M_1$ degenerated by $r_{o2}$).\n\nClosed loop (shunt–shunt → both impedances drop by $1+T$):\n\n$$\\frac{V_{out}}{I_{in}}=\\frac{R_0}{1+T}\\approx\\frac1{g_{m2}},\\qquad\nR_{in}=\\frac{r_{o2}}{1+T}\\approx\\frac{1}{g_{m2}(1+g_{m1}r_{o1})},\\qquad\nR_{out}=\\frac{r_{o1}+r_{o2}+g_{m1}r_{o1}r_{o2}}{1+T}\\approx\\frac1{g_{m2}}$$\n\n(Direct KCL with a test source gives exactly the same expressions.)\n\n**With $\\lambda=\\gamma=0$** (Razavi's usual assumption): $R_0,T\\to\\infty$, so\n\n$$\\frac{V_{out}}{I_{in}}=\\frac{1}{g_{m2}},\\qquad R_{in}=0,\\qquad R_{out}=\\frac{1}{g_{m2}}.$$\n\n## 4. Interpretation\n\n- Because $I_1$ pins $I_{D1}$, $V_{GS1}$ and therefore $V_X$ cannot move: node X behaves as a \"virtual\" fixed voltage $V_b-V_{GS1}$, giving an input impedance far below the $1/g_{m1}$ of a plain CG stage (reduced by the loop gain, roughly by the factor $g_{m1}r_{o1}$).\n- The loop forces $M_2$ to absorb the entire signal current: $g_{m2}v_{sg2}=-I_{in}$, hence $V_{out}=+I_{in}/g_{m2}$ (positive sign: pushing current into X raises $V_{out}$). Seen from the output, $M_2$ looks like a diode‑connected device, which is why $R_{out}\\approx1/g_{m2}$.\n- Functionally it is an \"active\" (feedback‑enhanced) diode / low‑input‑impedance current‑to‑voltage converter — the input stage of a regulated current mirror if $V_{out}$ also drives another PMOS gate.\n- Example: $g_mr_o=20$ for both devices, $g_{m2}=1\\,$mS, $r_{o2}=20\\,$k$\\Omega$ → $T\\approx420$, $V_{out}/I_{in}\\approx 998\\,\\Omega$, $R_{in}\\approx48\\,\\Omega$, $R_{out}\\approx1.05\\,$k$\\Omega$.\n- Dynamics: two poles (node X, low impedance → fast; output node, high open‑loop impedance → dominant). The closed‑loop bandwidth is roughly $(1+T)\\omega_{p,out}\\approx g_{m2}/C_{out}$; a large capacitance at X (e.g. a photodiode) can reduce phase margin, as in any shunt‑shunt TIA.",
        "format": "markdown",
        "sha256": "de50bc0d1ba538a36327332e628a4aeda78fcc0f9200d7004c272646ba1db9db"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS and M2 as the PMOS feedback device, describes the loop back to the input node, and gives the very low input resistance and approximately 1/gm2 transimpedance/output resistance required for full credit.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 23215,
        "total_tokens": 25581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20691,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 23215,
        "total_tokens": 25581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20691,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n| Device | Type | Role |\n|---|---|---|\n| M1 | NMOS, gate at fixed Vb, source = node X (input), drain = Vout | common‑gate (CG) amplifier, loaded by current source I1 |\n| M2 | PMOS, source = VDD, gate = Vout, drain = node X | common‑source transconductor that feeds a current back into the input node |\n| Iin | input signal current injected into X | – |\n| I2 (unlabelled source) | bias current sink at X | sets ID2 = I2 − I1 |\n\nSo the signal path is X → M1 (CG, non‑inverting) → Vout → M2 (CS, inverting) → current back into X. A rise in VX lowers VGS1, lowers ID1, raises Vout (I1 is constant), lowers VSG2, so M2 sources less current into X and VX falls: **negative feedback**. The loop senses the *voltage* at the output and returns a *current* to the input (“voltage–current”, i.e. shunt–shunt feedback). Hence both the input and the output impedance are lowered by (1 + loop gain), and the circuit behaves as a **transimpedance amplifier / very‑low‑impedance current input stage**.\n\n## 2. DC operating point\n- ID1 = I1 → VX = Vb − VGS1 (VGS1 for ID = I1).\n- KCL at X: ID2 = I2 − I1 (plus any DC part of Iin); need I2 > I1.\n- The loop itself fixes Vout: Vout = VDD − VSG2, where VSG2 is the value that makes M2 carry I2 − I1. No separate bias is needed at Vout.\n- Saturation: Vout − VX ≥ VGS1 − VTH1 for M1; VDD − VX ≥ VSG2 − |VTH2| for M2.\n\n## 3. Small‑signal analysis (ideal current sources, gmb1, ro1, ro2 included)\n\n**Node Vout:** I1 is an open circuit and M2’s gate draws no current, so M1 carries **no** small‑signal current:\n\nid1 = −(gm1+gmb1)vx + (vout − vx)/ro1 = 0  ⇒ vout = [1 + (gm1+gmb1)ro1]·vx\n\nM1 therefore acts purely as a voltage “sense amplifier” with gain ≈ (gm1+gmb1)ro1 from X to the output.\n\n**Node X:** the whole input current is absorbed by M2:\n\niin = gm2·vout + vx/ro2\n\n**Input impedance**\n\nRin = vx/iin = ro2 ∥ 1 / { gm2 [1 + (gm1+gmb1)ro1] } ≈ 1 / [gm2 (gm1+gmb1) ro1]\n\ni.e. the 1/gm of a CG stage is further divided by ≈ gm2·ro1 (a few tens to hundreds). Example: gm1 = gm2 = 1 mS, gmb1 = 0.2 mS, ro = 50 kΩ → Rin ≈ 16 Ω.\n\n**Transimpedance gain**\n\nvout/iin = [1 + (gm1+gmb1)ro1]·Rin = ro2[1+(gm1+gmb1)ro1] / {1 + gm2ro2[1+(gm1+gmb1)ro1]} ≈ **+1/gm2**\n\n(physically: to absorb iin, M2’s current must drop by iin, so Vout must rise by iin/gm2).\n\n**Output impedance** (Iin open, test voltage at Vout):\n\nRout = [ro1 + ro2 + (gm1+gmb1)ro1ro2] / {1 + gm2ro2[1+(gm1+gmb1)ro1]} ≈ **1/gm2**\n\n## 4. Feedback viewpoint (checks the above)\n- Open loop (M2 gate grounded): Rin,open = ro2; Rout,open = ro1 + ro2 + (gm1+gmb1)ro1ro2; open‑loop transimpedance = ro2[1+(gm1+gmb1)ro1].\n- Feedback factor (current returned per volt of output) = gm2.\n- Loop gain T = gm2ro2[1 + (gm1+gmb1)ro1] (≫ 1).\n- Closed loop: every quantity above divided by (1 + T) → exactly the results of Section 3; the transimpedance tends to 1/β = 1/gm2.\n\n## 5. Remarks\n- Purpose: make node X a near‑virtual‑ground for a current signal (e.g. current‑mode input, TIA/regulated‑cascode‑type front end). Note that the signal current flows through M2, not M1, so a PMOS sharing M2’s gate would copy iin with very low input impedance (current‑conveyor/mirror style).\n- With a finite output load RL (finite ro of I1): vout/vx = [1+(gm1+gmb1)ro1]·RL/(RL+ro1), Rin = 1/{(gm2 + 1/RL)·(vout/vx) + 1/ro2}, gain ≈ 1/(gm2 + 1/RL).\n- Dynamics: the loop contains two nodes (high‑impedance Vout, low‑impedance X). Large T plus capacitance at X (e.g., a photodiode) can give poor phase margin/peaking, so a real design must check stability.",
        "format": "markdown",
        "sha256": "376c8f7b255d4fe834247f2a3c23578f4aacb1ba1b2764512b5bd79432e5caa5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS and M2 as the PMOS feedback device, traces the feedback path to the input node, and gives the expected very low input resistance and approximately 1/gm2 transimpedance and output resistance.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 22599,
        "total_tokens": 24965,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 22599,
        "total_tokens": 24965,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## 1. What the circuit is\n\n| Element | Type / role |\n|---|---|\n| **M1** | NMOS, gate at the fixed bias V_b (ac ground), source at node X, drain at V_out → a **common‑gate stage** (current in at the source, voltage out at the drain) |\n| **I₁** | (ideal) current‑source load of M1 |\n| **M2** | PMOS, source at V_DD, **gate at V_out, drain at X** → a transconductor that *senses* V_out and *returns* a current g_m2·v_out to the input node |\n| **I_in** | signal current injected into X |\n| unlabeled source (I_B) | dc bias current pulled out of node X |\n\n**DC bias**\n- I₁ forces I_D1 = I₁, so I_D2 = I_B − I₁ (requires I_B > I₁).\n- V_X = V_b − V_GS1.\n- The loop itself sets V_out = V_DD − |V_GS2| at the value that makes M2 carry exactly I_B − I₁. M1 stays saturated if V_DD − |V_GS2| ≥ V_b − V_TH1.\n\n**Feedback polarity (sign check):** I_in ↑ → v_X ↑ → V_GS1 ↓ → I_D1 ↓ → V_out ↑ (I₁ is fixed) → |V_GS2| ↓ → I_D2 ↓ → less current into X → v_X ↓. The loop opposes the disturbance: **negative feedback**.\n\n**Topology:** output *voltage* is sensed (gate of M2 in parallel with V_out) and a *current* is returned in shunt with I_in → **voltage–current (shunt–shunt) feedback**. The forward amplifier is a transimpedance amplifier (R₀ = v_out/i_in) and the feedback network is a transconductance g_mF = g_m2. Hence\n\n  Closed‑loop transimpedance = R₀ / (1 + g_m2 R₀),  R_in and R_out both reduced by (1 + g_m2 R₀).\n\n## 2. Open‑loop (loaded) forward amplifier\n\nBreak the loop at the gate of M2:\n- Loading at the output: the gate of M2 draws no current → **no loading**.\n- Loading at the input: M2 with grounded gate presents **r_o2** at node X. (Bias sources are ideal → open.)\n\nBecause I₁ is ideal, no *signal* current can flow in M1; all of i_in flows through r_o2:\n\n v_x = i_in·r_o2,  and from i_d1 = 0: −(g_m1+g_mb1)v_x + (v_out − v_x)/r_o1 = 0\n\n ⇒ **R₀ = v_out/i_in = r_o2 [1 + (g_m1 + g_mb1) r_o1] ≈ (g_m1+g_mb1) r_o1 r_o2**\n\n R_in,open = r_o2  R_out,open = r_o1 + r_o2 + (g_m1+g_mb1) r_o1 r_o2 (cascode)\n\n**Loop gain:** T = g_m2 R₀ = g_m2 r_o2 [1 + (g_m1+g_mb1) r_o1] ≫ 1 (≈ product of two intrinsic gains).\n\n## 3. Closed‑loop results\n\n- Transimpedance:\n v_out / i_in = r_o2[1+(g_m1+g_mb1)r_o1] / {1 + g_m2 r_o2[1+(g_m1+g_mb1)r_o1]} **≈ 1/g_m2**\n\n- Input resistance:\n R_in = r_o2 / {1 + g_m2 r_o2[1+(g_m1+g_mb1)r_o1]} **≈ 1/[g_m2 (g_m1+g_mb1) r_o1]**\n (much lower than the 1/(g_m1+g_mb1) of a plain common‑gate stage – a \"virtual ground\")\n\n- Output resistance:\n R_out = [r_o1 + r_o2 + (g_m1+g_mb1)r_o1 r_o2] / {1 + g_m2 r_o2[1+(g_m1+g_mb1)r_o1]} **≈ 1/g_m2**\n\nWith λ = γ = 0 these become exactly: gain = 1/g_m2, R_in → 0, R_out = 1/g_m2.\n\n## 4. Check by direct KCL (no feedback approximations)\n\nNode V_out: only I₁ (open), M2's gate (open) and M1's drain connect there ⇒ i_d1 = 0 ⇒ v_out = [1 + (g_m1+g_mb1)r_o1] v_x.\nNode X: i_in = g_m2 v_out + v_x / r_o2.\n\nEliminating v_x gives exactly the closed‑loop transimpedance above, confirming the feedback analysis.\n\n## 5. Interpretation\n\nSince M1 cannot carry any signal current (ideal I₁), the input current must be absorbed entirely by M2. The high‑gain common‑gate stage M1 simply drives the gate of M2 until g_m2·v_out = i_in, i.e. **v_out = i_in/g_m2**: the output voltage is whatever gate voltage M2 needs to sink the input current. The loop makes node X a very low‑impedance point, exactly as in a regulated‑cascode / active‑feedback current input.\n\n**Numerical feel** (g_m1 = g_m2 = 1 mS, g_mb1 = 0.2 mS, r_o1 = r_o2 = 50 kΩ): R₀ ≈ 3.05 MΩ, T ≈ 3050, v_out/i_in ≈ 1.0 kΩ (≈1/g_m2), R_in ≈ 16 Ω (vs. 833 Ω for a bare CG stage), R_out ≈ 1.0 kΩ.\n\n**Remarks:** if I₁ has a finite resistance R₁, R₀ = R₁r_o2[1+(g_m1+g_mb1)r_o1]/{r_o2[1+(g_m1+g_mb1)r_o1]+R₁+r_o1} and the same closed‑loop formulas apply. The loop contains two nodes (X and V_out); the pole at the low‑impedance node X is at high frequency, so the output node is normally the dominant pole and the loop is well behaved, but with such large loop gain stability should still be checked.",
        "format": "markdown",
        "sha256": "92b4a559aa45b2979d6f5471b196d4401f43175e5ff097e2764eb024672b9df8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS and M2 as the PMOS feedback device driven by Vout, describes the feedback path to the input node, and derives the very low input resistance with transimpedance and output resistance approaching 1/gm2.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 20195,
        "total_tokens": 22561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2366,
        "output_tokens": 20195,
        "total_tokens": 22561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.** Making the load capacitors large only lowers the frequency of oscillation; it does not kill the oscillation.\n\nReasoning:\n\n- Model each inverter near its trip point as a stage with gain –A₀ and one pole at the output:\n  H₁(s) = –A₀ /(1 + s/ω₀), with ω₀ = 1/(R_out·C_L).\n\n- For the three‑stage loop, the total phase shift reaches 180° (plus the dc inversion) when each stage contributes 60°, i.e. at\n  ω_osc = √3·ω₀ = √3 /(R_out·C_L).\n\n- At that frequency each stage's gain magnitude is A₀/√(1+3) = A₀/2, so the loop gain is A₀³/8. The Barkhausen (start‑up) condition is therefore simply A₀ ≥ 2 per stage — a condition that contains no C_L at all. (Equivalently, the closed‑loop poles are at s = ω₀[(A₀/2 – 1) ± j(√3/2)A₀]; their real part is positive whenever A₀ > 2, for any C_L.)\n\n- A CMOS inverter has a small‑signal gain (g_mn+g_mp)(r_on‖r_op) well above 2, so the loop gain condition is always satisfied.\n\nThus, as C_L → ∞, ω₀ → 0 and the circuit still oscillates—just at an arbitrarily low frequency (and with a longer start‑up time). In the time domain, each inverter simply charges/discharges a huge capacitor slowly, so the node waveforms become slow ramps/sinusoids with a period proportional to C_L, but the ring never settles to a stable dc state.",
        "format": "markdown",
        "sha256": "5a8686c11265bf36df7adca1d622b6df02a8479e0d5644f582f33e2556fea597"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the ring continues oscillating at a lower frequency, and its small-signal analysis shows the oscillation condition is independent of capacitance.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 4462,
        "total_tokens": 6862,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3892,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 4462,
        "total_tokens": 6862,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3892,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.** The capacitors only set the *frequency* of oscillation, not *whether* the loop oscillates.\n\nEach inverting stage has a transfer function\n\n$$H_1(s)=\\frac{-A_0}{1+s/\\omega_0},\\qquad \\omega_0=\\frac{1}{R_{out}C_L}$$\n\nso the loop gain is $H(s)=-A_0^3/(1+s/\\omega_0)^3$.\n\nFor oscillation, the loop must provide an extra 180° of frequency‑dependent phase shift, i.e. 60° per stage:\n\n$$\\tan^{-1}\\!\\frac{\\omega_{osc}}{\\omega_0}=60^\\circ \\;\\;\\Rightarrow\\;\\; \\omega_{osc}=\\sqrt{3}\\,\\omega_0=\\frac{\\sqrt3}{R_{out}C_L}$$\n\nand at that frequency the loop‑gain magnitude must be at least unity:\n\n$$\\frac{A_0^3}{\\left(\\sqrt{1+3}\\right)^3}=\\frac{A_0^3}{8}\\ge 1\\;\\;\\Rightarrow\\;\\; A_0\\ge 2 .$$\n\nThe gain requirement ($A_0 \\ge 2$ per stage) contains no $C_L$ at all. Making $C_L$ larger simply moves the pole $\\omega_0$ down, and the frequency at which each stage contributes 60° moves down with it; the loop‑gain magnitude at that frequency stays $A_0^3/8$. The same conclusion follows from the large‑signal (delay) picture: each node just charges and discharges more slowly, so the period ($\\approx 6\\,t_d$) grows in proportion to $C_L$.\n\nThus the circuit continues to oscillate as $C_L$ grows arbitrarily large – it merely oscillates at an arbitrarily low frequency (and takes correspondingly longer to start up).",
        "format": "markdown",
        "sha256": "93bbcea5cd9e981e1775264852323082822008eb5b15b3edd919f12106825253"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that equal capacitors at all three nodes do not prevent oscillation: they lower the oscillation frequency while leaving the phase and gain conditions independent of capacitance. The small-signal and delay explanations are sound.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 3442,
        "total_tokens": 5842,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2801,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 3442,
        "total_tokens": 5842,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2801,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No.** Making the capacitors larger only lowers the oscillation frequency; it does not destroy the oscillation.\n\n**Reasoning**\n\nEach stage (an inverting amplifier with output resistance R and load C_L) has\n\nH(s) = −A₀ / (1 + s/ω₀), ω₀ = 1/(R·C_L)\n\nso the loop gain is −A₀³/(1 + s/ω₀)³.\n\nFor oscillation (Barkhausen), the three poles must together add 180° to the 180° DC inversion, i.e. each stage must contribute 60°:\n\ntan⁻¹(ω_osc/ω₀) = 60° → ω_osc = √3·ω₀ = √3 /(R C_L)\n\nAt that frequency each stage's gain magnitude is A₀/√(1 + 3) = A₀/2, so the loop gain is\n\n|H_loop(jω_osc)| = A₀³/8 ≥ 1 → A₀ ≥ 2\n\n**Key point:** the loop-gain magnitude at the phase-crossover frequency, A₀³/8, does not contain C_L at all. Increasing C_L shifts both the magnitude and the phase response along the frequency axis by the same factor, so the frequency where the total phase reaches 180° moves down, but the gain at that frequency stays A₀/2 per stage. The DC gain A₀ (= g_m R) is also independent of C_L.\n\nHence, as C_L → ∞, the oscillation frequency ω_osc = √3/(R C_L) → 0 (equivalently, each inverter's delay T_D grows and the period ≈ 6T_D grows), but the circuit still oscillates as long as A₀ > 2.",
        "format": "markdown",
        "sha256": "0d598d00c3d97f83c62b31b40d8afeaf674f0760a1ec8e026f9a3df8889f6fe9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that all three capacitors lower the oscillation frequency without stopping oscillation, and supports this with the valid per-stage phase and gain condition.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 3318,
        "total_tokens": 5718,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2753,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2400,
        "output_tokens": 3318,
        "total_tokens": 5718,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2753,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** the oscillation frequency halves, the power stays the same, and the phase noise at a given offset frequency falls by about 6 dB (a factor of 4). Normalized to the (new, lower) carrier frequency, i.e. at the same Δf/f₀, nothing changes.\n\n**Why**\n\n1. *Frequency and power.* Each stage delay is T_D ≈ C_L·V_DD/(2I_D), so doubling C_L doubles T_D and f₀ = 1/(6T_D) drops by 2. The dynamic power P = 3C_L·V_DD²·f₀ ≈ I_D·V_DD is unchanged (same current, flowing for twice as long, half as often).\n\n2. *Jitter per transition.* During a transition the device noise current (4kTγg_m) is integrated on C_L up to the switching threshold:\n v_n² ≈ 2kTγg_m·T_D/C_L² ∝ kT/C_L → halves,\n but the slope I_D/C_L also halves, so the timing error per edge\n σ_t² = v_n²/(slope)² = 2kTγg_m·T_D/I_D² ∝ C_L → doubles.\n The absolute period jitter rises by √2, while the period doubles, so the *relative* jitter improves by √2.\n\n3. *Phase noise.* For white (uncorrelated) noise the phase performs a random walk and\n L(Δf) = f₀³·σ_T²/Δf².\n With f₀³ → 1/8 and σ_T² → ×2, L(Δf) → 1/4, i.e. −6 dB at a fixed Δf. The same conclusion follows from the general ring‑oscillator result L(Δf) ∝ (kT/P)(f₀/Δf)²: P is fixed and f₀ is halved.\n\nSo the 6 dB improvement is \"bought\" purely with frequency: at the same fractional offset the phase noise (and the figure of merit) is unchanged. If you then restored the original frequency by doubling the transistor widths/currents, the power would double and the net improvement would be only 3 dB.",
        "format": "markdown",
        "sha256": "2a24a01e4276132d59b3ae60e86054f6debdb760f6ca4a7667e2176b4002b6aa"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and reduces phase noise by about 6 dB at a fixed offset, while it is unchanged at the same fractional offset. The reasoning matches the golden solution.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 23052,
        "total_tokens": 25444,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22349,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 23052,
        "total_tokens": 25444,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22349,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** the oscillation frequency is halved and the phase noise at a given offset Δf drops by a factor of 4 (≈ 6 dB) – but only because the carrier frequency has halved; relative to the carrier (or in terms of FoM) nothing is gained.\n\n**Why:**\n\n1. **Frequency.** Each stage delay is set by the time the inverter current I_D needs to swing C_L through about V_DD/2: T_D ≈ C_L·V_DD/(2I_D). Doubling C_L doubles T_D, so f_osc = 1/(6T_D) is halved.\n\n2. **Jitter per transition.** During a transition the transistor's white noise current (PSD ≈ 4kTγg_m) integrates on C_L for a time T_D, giving a noise voltage variance ∝ T_D/C_L² (this *halves*). But the slope of the edge, I_D/C_L, also halves, so the timing error σ_t² = σ_v²/(slope)² = 2kTγg_m·T_D/I_D² **doubles** (it is proportional to T_D ∝ C_L). The period jitter variance therefore doubles (σ_T rises by √2).\n\n3. **Phase noise.** For white noise, L(Δf) = f_osc³·σ_T²/Δf². With f_osc → f_osc/2 and σ_T² → 2σ_T², L falls by (1/8)(2) = 1/4, i.e. −6 dB. Equivalently, the ring‑oscillator result\n\n L(Δf) ≈ (2kTγg_m/I_D²)(f_osc/Δf)² = 2kTγg_m /(N²C_L²V_DD²Δf²)\n\n shows L ∝ 1/C_L² (∝ f_osc² at fixed current).\n\n4. **No real improvement.** Since f_osc also dropped 6 dB (20log 2), the phase noise normalized to the carrier is unchanged, and the power (≈ N·C_L·V_DD²·f_osc) is unchanged, so the FoM is identical. Doubling the capacitors is equivalent to following the original oscillator with a ÷2 divider – the absolute jitter per period actually gets worse by √2.",
        "format": "markdown",
        "sha256": "1fd69f92a008f55b043ccf1311cadc36c94c0ea311d003e5318946b563a55e34"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and reduces phase noise by a factor of four (about 6 dB) at a fixed offset, with supporting reasoning. Its fixed-relative-offset qualification is also consistent with the solution.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 19238,
        "total_tokens": 21630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18498,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 19238,
        "total_tokens": 21630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18498,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** at a given offset frequency the phase noise *falls by about 6 dB (a factor of 4)* – but only because the oscillator is now running at half the frequency. Nothing \"fundamental\" is gained: the power is unchanged and the FOM stays the same.\n\n**Why**\n\n1. **Frequency.** Each inverter drives its load with roughly a constant current I, so the delay per stage is t_d ≈ C_L·V_DD/(2I). Doubling C_L doubles t_d, doubles the period, and halves f_osc.\n\n2. **Jitter per transition.** The inverter's thermal‑noise current (PSD ≈ 4kTγg_m, unchanged because the devices and their currents are unchanged) is integrated on the node capacitance during the edge:\n - noise voltage at the switching point: σ_v² ∝ S_i·t_d / C_L² → ×2/×4 = ½ (3 dB less voltage noise),\n - but the edge slope I/C_L is also halved, so the timing error σ_t = σ_v·C_L/I has σ_t² ∝ S_i·t_d/I² → **doubles**.\n (Equivalently: a noise charge Δq shifts the edge by Δq/I, independent of C_L, but the edge now lasts twice as long, so twice as much noise charge is collected.)\n\n3. **Phase noise.** For white noise, L(Δf) = σ_T²·f_osc³/Δf², where σ_T² (period jitter, 6 transitions) has doubled and f_osc has halved:\n L → 2 × (1/8) = 1/4 ⇒ **−6 dB at the same Δf.**\n This is just the familiar L(Δf) ∝ (kT/P)(f_osc/Δf)² with f_osc halved and P fixed.\n\n4. **No free lunch.** Power P ≈ 3C_L·V_DD²·f_osc is unchanged (capacitance doubled, frequency halved), and 20log(f_osc/Δf) also drops 6 dB, so FOM = L − 20log(f_osc/Δf) + 10log(P/1 mW) is unchanged; at a fixed *relative* offset Δf/f_osc the phase noise is identical. Doubling the capacitors simply trades oscillation frequency for phase noise.",
        "format": "markdown",
        "sha256": "17210a7931762c6cb4bbb983aa8bf20841225e4b22be36f046c58433ffb59d3c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and lowers phase noise by about 6 dB (a factor of four) at a fixed offset, with a supporting noise/jitter argument. The fixed-relative-offset qualification is also correct.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 15263,
        "total_tokens": 17655,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14489,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2392,
        "output_tokens": 15263,
        "total_tokens": 17655,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14489,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: yes.** With any finite gain per stage, making C_L large enough stops the oscillation – a heavily loaded node acts like a dominant‑pole (compensation) capacitor and stabilizes the loop.\n\n**Why (frequency domain)**\n\nModel each stage as –A₀/(1+s/ω_p). Let the node with C_L have its pole at ω₁ = 1/(R_out C_L) and the other two nodes at ω₀ = 1/(R_out C). The loop transmission is\n\nH(s) = –A₀³ / [(1+s/ω₁)(1+s/ω₀)²]\n\n*Phase condition:* tan⁻¹(ω/ω₁) + 2 tan⁻¹(ω/ω₀) = 180°.\nAs C_L → ∞, ω₁ → 0 and the first term → 90° at any frequency of interest. The other two poles must then supply 45° each, so ω_osc → ω₀ (it does *not* go to zero).\n\n*Gain condition at ω ≈ ω₀:*\n\n|H(jω₀)| ≈ A₀³ · (ω₁/ω₀) · 1/(√2·√2) = A₀³ C / (2 C_L)\n\nThis falls below unity once C_L ≳ A₀³C/2 (exact Routh–Hurwitz result: oscillation only while 2τ₁² – (A₀³–4)ττ₁ + 2τ² < 0, with τ₁ = R_outC_L, τ = R_outC). For \"arbitrarily large\" C_L the loop gain at the 180° frequency → 0, Barkhausen's criterion cannot be met, and the circuit does not oscillate. (E.g., with A₀ = 2 the ring oscillates only if C_L = C exactly; with A₀ = 3, only if C_L ≲ 13C.)\n\n**Why (intuitive / time domain)**\n\nWhen C_L is huge, the loaded node moves so slowly that the other two inverters follow it essentially instantaneously. The loop then degenerates into a single slow (integrating) node inside a loop with net inversion – i.e., plain negative feedback with one dominant pole, exactly like a compensated multistage op amp. As the slow node creeps toward the switching threshold, the next two stages respond at once and reduce the first inverter's drive current *before* the node can overshoot, so everything settles with all three nodes sitting at the inverter trip point (≈V_DD/2). No overshoot → no regeneration → no oscillation.\n\n**Caveat:** Only in the idealized limit of infinite stage gain (ideal switches) would the ring keep going as a slow relaxation oscillator. With real, finite‑gain stages there is always a C_L beyond which the ring just \"sticks\" at V_DD/2 – a practical warning against loading one node of a ring oscillator (e.g., with a large buffer) much more heavily than the others.",
        "format": "markdown",
        "sha256": "a4abe5b702acb5c604aff385facfadf6c87fcd79c6ee9c77baeb71f6f2db19fc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that sufficiently large loading on one node creates a dominant pole, reduces loop gain at the phase-crossover frequency, and prevents sustained oscillation. The secondary frequency and time-domain explanations are consistent with the essential result.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 15648,
        "total_tokens": 17940,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14683,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 15648,
        "total_tokens": 17940,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14683,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes.** If C_L is made large enough the loop stops oscillating altogether – it does not simply oscillate more slowly. Here is why.\n\n**Model.** Let each inverter have small‑signal gain −A₀ and an output pole ω_p = 1/(R_out·C). The loaded node X has a pole at ω_p1 = 1/[R_out(C + C_L)] = ω_p/k, with k = (C + C_L)/C. The loop gain is\n\nH(s) = −A₀³ / [(1 + s/ω_p1)(1 + s/ω_p)²].\n\n**Phase condition.** Oscillation requires the three poles to add 180°:\narctan(ω/ω_p1) + 2·arctan(ω/ω_p) = 180°.\nAs C_L → ∞ the loaded stage contributes ≈ 90°, so the other two stages must each contribute 45°, i.e. ω_osc → ω_p. Solving exactly gives ω_osc = ω_p·√(1 + 2/k). So the frequency falls only from √3·ω_p (k = 1) toward ω_p – it never approaches zero, because the two unloaded stages cannot supply 90° at a lower frequency.\n\n**Gain condition.** At that frequency,\n\n|H| = A₀³ / [√(1+(ω_osc/ω_p1)²)·(1+(ω_osc/ω_p)²)] = A₀³·k / [2(k+1)²].\n\nFor k = 1 this gives the familiar A₀³/8 ≥ 1 (A₀ ≥ 2). For large k it becomes ≈ A₀³/(2k) → 0: the loaded stage's gain at ω_p is only A₀·ω_p1/ω_p ≈ g_m/(C_L·ω_p), which shrinks as 1/C_L. Barkhausen's gain condition fails once 2(k+1)²/k > A₀³, i.e. roughly C_L ≳ (A₀³/2)·C. (With the minimum gain A₀ = 2, *any* added C_L kills the oscillation; with A₀ = 10, C_L ≈ 500·C does.)\n\n**Intuition.** Three inversions make this a negative‑feedback loop; it oscillates only because three comparable poles give 180° of phase lag while the gain is still above unity. A huge C_L creates a dominant pole, moving the unity‑gain crossover down to ≈ A₀³·ω_p1 ≪ ω_p, where the other two poles add little phase. The loop acquires positive phase margin and becomes stable – exactly the mechanism of dominant‑pole compensation in op amps.\n\n**Large‑signal view (CMOS inverters).** With a huge C_L, V_X can move only by (I/C_L)·t_d during the delay of the fast path through the other two inverters. When this excursion falls below the input transition width of the next inverter (≈ V_DD/A₀), the other stages can no longer switch fully, the swing collapses, and the circuit settles with all three nodes sitting at the inverter trip point (≈ V_DD/2). The loop has turned into a self‑biased amplifier stuck at its metastable point, not an oscillator.",
        "format": "markdown",
        "sha256": "cfc8f0e20477f694952c46a308551b843a520514bd292613473a65ef7b962beb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large capacitance on one node creates a dominant pole and reduces loop gain below the Barkhausen requirement, so oscillation can cease. The phase and gain analysis is consistent with that conclusion.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 22384,
        "total_tokens": 24676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21318,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 22384,
        "total_tokens": 24676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21318,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: Yes.** For a sufficiently (and certainly for an arbitrarily) large C_L the ring stops oscillating; it simply settles with all three inverters sitting at their trip points. The frequency does *not* keep falling toward zero as C_L grows – instead the swing at the loaded node collapses and the oscillation dies.\n\n**Why (small‑signal view)**\n\nModel each inverter near its trip point as gain −A₀ with output resistance R, with capacitance C at the two unloaded nodes (pole ω₀ = 1/RC) and C_L at node X (pole ω_X = 1/RC_L). The loop gain is\n\nH(s) = −A₀³ / [(1 + s/ω_X)(1 + s/ω₀)²]\n\nFor oscillation the three stages must supply 180° of frequency‑dependent phase shift with |H| ≥ 1.\n\n- With C_L very large, the loaded stage gives almost 90° at any frequency of interest – but no more than 90°.\n- The remaining 90° must come from the two unloaded stages: 45° each, which happens only at ω ≈ ω₀.\n- At ω₀ the loaded stage has already lost most of its gain: |A₀/(1 + jω₀/ω_X)| ≈ A₀ ω_X/ω₀ = A₀ C/C_L. The loop gain at the 180° frequency is therefore\n\n |H| ≈ A₀³ (C/C_L)/2\n\n(Routh's criterion gives the exact condition A₀³ω_X ≥ 2ω_X²/ω₀ + 4ω_X + 2ω₀, which reduces to A₀ ≥ 2 for the unloaded ring and to C_L ≤ A₀³C/2 for C_L ≫ C.)\n\nSo once C_L exceeds roughly A₀³C/2, the loop gain falls below unity before the phase reaches 180°; the closed‑loop poles stay in the left half plane and nothing oscillates. In effect, the big capacitor is dominant‑pole compensation: the three‑pole negative‑feedback loop (three inversions = negative feedback at dc) acquires a phase margin approaching 90° and becomes a stable amplifier. Because CMOS inverters have a large A₀ at the trip point, C_L must be very large (hundreds to thousands of times C) – but \"arbitrarily large\" certainly gets there.\n\n**Why (large‑signal view)**\n\nNode X can move only extremely slowly (slope I/C_L). The instant it creeps past the trip point of the second inverter, inverters 2 and 3 flip almost immediately and inverter 1 reverses the current into C_L, pushing X back. The excursion of X is only about 2T_D·I/C_L, which → 0 as C_L → ∞, so the following inverters never leave their linear region and the loop settles at the trip point (drawing static current). Before the oscillation dies, the frequency does not go to zero – it saturates at a value set by the two unloaded stages (≈ω₀, i.e. a period of ≈8T_D instead of 6T_D), while the swing at X shrinks; once the loop gain at that frequency drops below one, the oscillation ceases entirely.",
        "format": "markdown",
        "sha256": "579048a245884082b250e4db18283106d04f58242eb8032ce9b4aaeaa1e023d1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large capacitance on one node can stop oscillation and explains the dominant-pole gain roll-off that makes the loop fail the oscillation condition. The supporting phase, gain, and time-domain discussion is consistent with the essential result; exact threshold details are not required.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 21728,
        "total_tokens": 24020,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20660,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2292,
        "output_tokens": 21728,
        "total_tokens": 24020,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20660,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** the phase noise drops by 3 dB (the noise power is halved), while the oscillation frequency stays the same and the power dissipation doubles.\n\n**Why:**\n\n1. **Frequency is unchanged.** Doubling W doubles the drive current of each inverter, but it also doubles the capacitance seen at each node (gate and drain capacitances). The stage delay $T_D \\approx C\\,\\Delta V/I$ is therefore unchanged, and so is $f_{osc} = 1/(2N\\,T_D)$.\n\n2. **Noise is halved.** The scaled oscillator is exactly equivalent to two copies of the original ring oscillator placed in parallel, with corresponding nodes tied together. The two copies carry identical signals, but their device noise currents are uncorrelated. At each node the noise current *power* doubles ($4kT\\gamma g_m \\rightarrow 2\\times$), but the node impedance (set by $1/g_m$ and $1/(C\\omega)$) is halved, so the noise *voltage* power at the node, $\\overline{I_n^2}\\,|Z|^2$, is cut in half. \n\n   Equivalently, in the time domain: the noise charge accumulated during a transition, $\\int I_n\\,dt$, has twice the variance, but it is deposited on twice the capacitance while the slope at the zero crossing $(I/C)$ is unchanged, so the timing jitter variance is halved.\n\n3. **Price paid.** The current drawn from $V_{DD}$ doubles, so power consumption doubles. The improvement is thus the generic \"3 dB per doubling of power\" trade-off: the oscillator's figure of merit (which normalizes phase noise to power) does not change. (Flicker noise, which scales as $1/(WL)$, also drops by half, so the $1/f^3$ region improves by 3 dB as well.)",
        "format": "markdown",
        "sha256": "5733213ccfc5f90a2beb9be5d2c660f71d6ad6f1276d36378cf5249fac62eb66"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives the 3 dB reduction and supports it with valid parallel-ring and noise-scaling reasoning; frequency stays about the same and power doubles.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 7310,
        "total_tokens": 10927,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6691,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 7310,
        "total_tokens": 10927,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6691,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It drops by about 3 dB (a factor of 2) – at the cost of twice the power – while the oscillation frequency stays the same.**\n\nWhy:\n\n1. **Frequency is unchanged.** With no explicit load capacitors, each node is loaded only by device capacitances (gate of the next stage plus its own drains). Doubling W doubles the charging/discharging current *and* doubles the node capacitance, so the stage delay T_D ≈ C_L·V_DD/(2I_D) and hence f_osc = 1/(2N·T_D) do not change.\n\n2. **Noise per node halves.** Doubling all widths is exactly equivalent to connecting two identical copies of the original ring in parallel (node to node). Each copy produces the same waveform (same swing, same slope at the zero crossings), but their noise currents are uncorrelated. At each node the noise-current PSD doubles (∝ g_m, both thermal 4kTγg_m and flicker), but the node impedance is halved (2C_L), so the noise-voltage power ∝ I_n²·|Z|² goes down by 2·(1/4) = 1/2. Equivalently, the timing jitter of each transition, σ_t² ∝ kTγ g_m T_D / I_D², halves because g_m → 2g_m, I_D → 2I_D, T_D unchanged.\n\n3. **Phase noise.** Since L(Δf) ∝ f_0³·σ_T²/Δf² and f_0 is fixed, the phase noise falls by a factor of two (≈3 dB) in both the 1/f² and 1/f³ regions. This is the familiar result that ring-oscillator phase noise is inversely proportional to power: L ∝ kTγ/(I_D·V_overdrive)·(f_0/Δf)², so doubling I_D (and P) halves it.\n\nBecause the phase noise improves by 3 dB while power doubles, the figure of merit is unchanged – you are simply \"buying\" phase noise with power.",
        "format": "markdown",
        "sha256": "35f9e573631a10682276f98ccaa64621ccf4c52bf838ee648bc018f3835de29c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives an approximately 3 dB phase-noise reduction and explains the scaling: current and capacitance double, while noise-current PSD doubles and the node impedance halves, reducing node-noise power by a factor of two. The frequency and power consequences are also consistent with the golden solution.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 11713,
        "total_tokens": 15330,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11056,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 11713,
        "total_tokens": 15330,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11056,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It drops by 3 dB (at the cost of twice the power).**\n\nReasoning:\n\n1. **Frequency stays the same.** Doubling W doubles the drive current I_D of each transistor, but it also doubles the capacitance at each node (gate capacitance of the next stage plus the drain capacitances of the stage itself). The slope of each transition, dV/dt = I_D/C, and hence the gate delay (≈ C·V_DD/2I_D) are unchanged, so f_osc does not change.\n\n2. **Noise voltage at each node halves.** The noise current of each device, 4kTγg_m, doubles because g_m doubles, but this current is integrated/filtered by a capacitance that is twice as large. The noise voltage present at a node when it crosses the trip point of the next stage (∝ Ī_n²/C², or roughly kT/C) therefore falls by a factor of 2.\n\n3. **Jitter → phase noise.** The timing displacement of each edge is Δt = V_n/(dV/dt). With the slope unchanged and V_n² halved, the jitter variance (and therefore the phase noise, which is proportional to it at a given f_osc) falls by a factor of 2, i.e., 3 dB.\n\n4. **Power.** Since the current drawn from V_DD (≈ N·C·V_DD·f_osc) doubles, the power consumption doubles. This is the usual ring‑oscillator trade‑off: at a fixed frequency, phase noise scales inversely with power consumption (the FOM is unchanged).",
        "format": "markdown",
        "sha256": "4372c7b4df3bd9f92e42a73252bdf4318792cac98016a2c69a12b0485613e5a0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives a 3 dB phase-noise reduction and supports it with the valid scaling argument: doubled node capacitance halves the node-noise variance while the signal slope stays about the same. The frequency and power conclusions also match the golden solution.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 16927,
        "total_tokens": 20544,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3617,
        "output_tokens": 16927,
        "total_tokens": 20544,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the problem**\n\nIn its quiescent (bias) state every node of the odd‑stage ring sits at the inverter trip point (≈ V_DD/2 for a symmetric inverter), so all six transistors are in saturation. Apply a small test voltage v_x at the supply node and let the three output nodes change by v₁, v₂, v₃. Writing KCL at the output of inverter k (input v_{k‑1}, output v_k), neglecting capacitances:\n\n$$\ng_{mP}(v_x-v_{k-1})+\\frac{v_x-v_k}{r_{OP}} \\;=\\; g_{mN}v_{k-1}+\\frac{v_k}{r_{ON}}\n$$\n\nSolving the three coupled equations around the loop gives \n\n$$\nv_1=v_2=v_3=v=\\frac{g_{mP}+1/r_{OP}}{\\,g_{mP}+g_{mN}+1/r_{OP}+1/r_{ON}\\,}\\;v_x\n$$\n\ni.e., by symmetry all three nodes move by the same amount.\n\n**Key observation**\n\nBecause each inverter's input and output move together, every inverter behaves as if its input were shorted to its output: a *diode‑connected* PMOS in series with a *diode‑connected* NMOS. Each inverter therefore presents, between V_DD and ground, the impedance\n\n$$\n\\frac{1}{g_{mP}}\\Big\\|r_{OP}\\;+\\;\\frac{1}{g_{mN}}\\Big\\|r_{ON}\n$$\n\nThe supply current of each stage is $i=(g_{mP}+1/r_{OP})(v_x-v)$, and the total current is $i_x=3i$, which gives the same result directly:\n\n$$\nR_X=\\frac{v_x}{i_x}=\\frac{1}{3}\\left[\\frac{1}{g_{mP}}\\Big\\|r_{OP}+\\frac{1}{g_{mN}}\\Big\\|r_{ON}\\right]\n\\;\\approx\\;\\frac{1}{3}\\left(\\frac{1}{g_{mP}}+\\frac{1}{g_{mN}}\\right)\n$$\n\n**Result**\n\nThe three stages appear in parallel, each looking like a PMOS diode in series with an NMOS diode:\n\n$$\nR_X \\approx \\frac{1}{3}\\left(\\frac{1}{g_{mN}}+\\frac{1}{g_{mP}}\\right)\n$$\n\n(for g_mN = g_mP = g_m this is 2/(3g_m)). As a by‑product, the node voltages track the supply by $v/v_x = (1/g_{mN})/(1/g_{mN}+1/g_{mP}) = g_{mP}/(g_{mN}+g_{mP}) \\approx 1/2$, which is the familiar supply sensitivity of the inverter trip point.",
        "format": "markdown",
        "sha256": "ba5f92a1b9a3e68db80b8465d65eb7e1d26b76cdce52f9eae1d7bc261bab9159"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer analyzes only a static, diode-connected, gm-based resistance and ignores the oscillator’s charging and discharging of the load capacitances, which sets the supply resistance. The golden solution assigns this static-only approach a score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7456,
        "total_tokens": 10904,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6505,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7456,
        "total_tokens": 10904,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6505,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the small‑signal picture**\n\nAt the (unstable) equilibrium point of the ring, all three inverter outputs sit at the same trip voltage, so each inverter is biased with both transistors in saturation. Apply a small test voltage $v_x$ to the common supply node and find the current $i_x$ it draws.\n\nFor one inverter (input $v_{in}$, output $v_{out}$), KCL at the output gives\n\n$$\ng_{mP}(v_x-v_{in})+\\frac{v_x-v_{out}}{r_{OP}} \\;=\\; g_{mN}v_{in}+\\frac{v_{out}}{r_{ON}}\n$$\n\ni.e. $v_{out}=-A\\,v_{in}+B\\,v_x$ with $A=(g_{mN}+g_{mP})(r_{ON}\\|r_{OP})$ and $B=(g_{mP}+1/r_{OP})(r_{ON}\\|r_{OP})$.\n\nWriting this for the three stages of the loop,\n\n$$\nv_1=-Av_3+Bv_x,\\quad v_2=-Av_1+Bv_x,\\quad v_3=-Av_2+Bv_x ,\n$$\n\nthe determinant is $1+A^3\\neq0$, so the solution is unique, and by the cyclic symmetry of the ring it must be\n\n$$\nv_1=v_2=v_3=\\frac{B}{1+A}\\,v_x .\n$$\n\n**Key observation:** every inverter therefore has its *input equal to its output* in the small‑signal sense. Each NMOS has gate tied to drain (diode‑connected, impedance $1/g_{mN}\\|r_{ON}$ to ground) and each PMOS has gate tied to drain (diode‑connected, impedance $1/g_{mP}\\|r_{OP}$ between the supply node and the output). So each inverter looks like two diode‑connected devices in series between $v_x$ and ground, and the three inverters appear in parallel:\n\n$$\nR_X=\\frac{1}{3}\\left[\\left(\\frac{1}{g_{mP}}\\Big\\|r_{OP}\\right)+\\left(\\frac{1}{g_{mN}}\\Big\\|r_{ON}\\right)\\right]\n$$\n\nNeglecting channel‑length modulation,\n\n$$\nR_X\\approx\\frac{1}{3}\\left(\\frac{1}{g_{mN}}+\\frac{1}{g_{mP}}\\right)=\\frac{g_{mN}+g_{mP}}{3\\,g_{mN}g_{mP}},\n$$\n\nwhich reduces to $R_X\\approx 2/(3g_m)$ if $g_{mN}=g_{mP}=g_m$ — a fairly low resistance, which is why a supply‑tuned ring oscillator presents a heavy load to the circuit driving its supply node.",
        "format": "markdown",
        "sha256": "f650d356b3411a5268930e42bce831c746418e2366841472b773281aaa2de7b2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives a consistent-looking static, gm-based diode-connected resistance, but it ignores the oscillation-driven charging and discharging of the load capacitances that sets the supply-node resistance. The golden solution explicitly assigns this kind of static analysis a score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7723,
        "total_tokens": 11171,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6776,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7723,
        "total_tokens": 11171,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6776,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the small‑signal picture**\n\nAt the oscillator's quiescent (trip) point every inverter is biased with its input and output near V_DD/2, so each inverter is a PMOS (g_mP, r_OP) stacked on an NMOS (g_mN, r_ON). Apply a small‑signal voltage v_X at the common supply node and find the current i_X it draws.\n\nFor one inverter with input v_i and output v_{i+1}, KCL at the output gives\n\nv_{i+1} = B·v_X − A·v_i , with A = (g_mN+g_mP)(r_ON‖r_OP), B = (g_mP+1/r_OP)(r_ON‖r_OP).\n\nGoing around the three‑stage loop:\n\nv₁(1 + A³) = B(1 − A + A²)v_X  ⟹ v₁ = B·v_X/(1 + A),\n\nand by symmetry v₁ = v₂ = v₃. \n\n**Key observation:** since every node moves by the same amount, each inverter's input and output are at the *same* small‑signal potential, i.e., every inverter behaves as a *diode‑connected* PMOS in series with a *diode‑connected* NMOS between V_X and ground.\n\n**Resistance**\n\nOne such inverter presents, from V_X to ground,\n\n(1/g_mP ‖ r_OP) + (1/g_mN ‖ r_ON),\n\nand the three inverters appear in parallel. Hence\n\nR_X = (1/3)·[ (1/g_mP ‖ r_OP) + (1/g_mN ‖ r_ON) ] ≈ (1/3)(1/g_mP + 1/g_mN).\n\n(Check: KCL on one stage gives v_o = v_X(g_mP+1/r_OP)/(g_mP+g_mN+1/r_OP+1/r_ON); the current per inverter is (g_mP+1/r_OP)(v_X−v_o); multiplying by 3 and dividing into v_X yields the same result.)\n\nFor equal transconductances, g_mN = g_mP = g_m, R_X ≈ 2/(3g_m) — a fairly low resistance, which is why the supply node of a ring oscillator looks like a \"diode‑connected\" load (relevant when the ring is powered from a current source or regulator for frequency tuning).",
        "format": "markdown",
        "sha256": "d60f1804b90df205ad717ac870d48e8fea21e4c558e172dfe37c58d035ae4fff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The derivation is internally consistent for a static, diode-connected-inverter model, but it ignores the oscillation-driven charging and discharging of the load capacitances that dominate the supply resistance. The golden solution assigns this static gm-based answer a score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7615,
        "total_tokens": 11063,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6848,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3448,
        "output_tokens": 7615,
        "total_tokens": 11063,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6848,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: yes — once the ring oscillates, that small‑signal result no longer applies. The supply sees a periodically time‑varying load, not a fixed resistance, and the time‑averaged \"resistance\" is much larger (and set by switching, not by gm).**\n\n**Why the static answer is right (when the loop is quiescent)**\n\nThe \"diode‑connected\" picture looks suspicious because each gate is tied to the *previous* drain, not its own. But if the ring sits at its trip point (all nodes at ≈VDD/2, all devices saturated), a small supply wiggle v_x gives, for each stage,\n\nv_out = a·v_x − A·v_in,  A = (g_mn+g_mp)/(1/r_on+1/r_op), a = (g_mp+1/r_op)/(1/r_on+1/r_op)\n\nGoing around the loop, v₁ = a v_x − A v₃, v₂ = a v_x − A v₁, v₃ = a v_x − A v₂, whose unique solution (since (−A)³ ≠ 1) is v₁ = v₂ = v₃ = a v_x/(1+A). Every node moves identically, so for every inverter v_in = v_out — exactly the diode‑connected condition. Each inverter then presents (1/g_mn ∥ r_on) + (1/g_mp ∥ r_op) ≈ 1/g_mn + 1/g_mp, and the three in parallel give R_X ≈ (1/3)(1/g_mn + 1/g_mp). That analysis is valid only while the circuit actually sits at this (unstable) equilibrium.\n\n**What changes when it oscillates**\n\n1. Large‑signal operation: the nodes swing nearly rail‑to‑rail. The transistors spend almost all their time in cutoff or deep triode, not saturated at the trip point, so the g_m's in the formula don't describe the devices anymore. A linear small‑signal resistance isn't even well defined; the circuit is periodically time‑varying.\n\n2. The symmetry argument collapses: at any instant the three nodes are at different points of the cycle (roughly one high, one low, one switching), so an inverter's input no longer tracks its own output.\n\n3. What the supply actually sees: in an inverter whose output is settled high or low, one device is off, so there is no path from the supply node to ground — only a PMOS triode resistance to an already‑charged node capacitance (zero current). Only during a transition, when both devices are briefly on, does the supply see a low‑resistance (crowbar) path plus the charging current into the node capacitance. The supply current is therefore a train of pulses, one per rising edge, repeating at 3f_osc.\n\n4. Averaged over a period, the current is dominated by dynamic charging,\n I_avg ≈ 3·f_osc·C_node·VDD (+ a small short‑circuit term),\n so the effective resistance is roughly 1/(3 f_osc C_node) — typically tens of kΩ, versus a few hundred Ω from the g_m formula. It depends on frequency, capacitance and VDD (and since f_osc itself depends on VDD, the incremental dVDD/dI differs again — this is \"supply pushing\"). A small test signal at the supply would also produce current components at ω ± k·3f_osc, not a simple proportional response.\n\nSo the (1/3)(1/g_mn + 1/g_mp) result describes only the hypothetical quiescent state (e.g., before oscillation builds up or if the loop gain is too low to oscillate). In steady‑state oscillation R_X becomes time‑varying, and on average much higher, governed by switching rather than by transconductance.",
        "format": "markdown",
        "sha256": "9277a146127e93ba26e77665b1fc2dc74ac01cc0c43ca680fb4b7571c4381915"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It identifies the capacitive charging mechanism and gives the correct average-current relation, but concludes that RX becomes much higher than the static estimate. The frequency scales inversely with the stage delay, so RX remains on the order of the MOS on-resistance rather than becoming much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 13804,
        "total_tokens": 17366,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12597,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 13804,
        "total_tokens": 17366,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12597,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: yes.**\n\n**Why the original number is right only at the quiescent point**\n\nThe expression R_X ≈ (1/3)(1/g_mn + 1/g_mp) assumes the ring sits at its metastable operating point: every inverter has V_in = V_out ≈ V_DD/2, both devices are in saturation, and – because the loop forces all three nodes to move by the same amount when V_X is perturbed – the gate and drain of every transistor move together. Each transistor is therefore effectively diode‑connected, each inverter looks like 1/g_mp + 1/g_mn (more exactly 1/(g_mp+1/r_op) + 1/(g_mn+1/r_on)), and three identical inverters in parallel give the factor 1/3.\n\nBut that operating point is unstable for any inverter with gain > 2 (a CMOS inverter has gain ≫ 2), so a real ring does not stay there – it oscillates, and the formula then describes a state the circuit never occupies.\n\n**What changes when it oscillates**\n\n1. The node voltages swing almost rail‑to‑rail, so the devices are driven through cutoff, saturation and triode. g_m, r_o, and hence R_X, are no longer constants: R_X becomes a periodically time‑varying quantity (period T_osc/3 by the three‑fold symmetry), not a single number.\n\n2. Most of the time each inverter has one device off and the other in deep triode:\n   - output high: NMOS off, PMOS is a triode switch from X to a purely capacitive node → no low‑frequency current (only R_on,p in series with C_L at high frequency);\n   - output low: PMOS off (its gate sits at V_DD, following X) → no current.\n   Only an inverter in the middle of a transition conducts from X, and then V_in ≠ V_out, so the \"two diodes in series\" picture is invalid and the g_m values are those of a different bias current anyway.\n\n3. The supply current is therefore a train of pulses (load‑charging current plus crowbar current during transitions). The meaningful incremental \"resistance\" at X is the relation between ΔV_DD and the change in average current, ≈ d(3 f_osc C_L V_DD + I_crowbar)/dV_DD, which depends on load capacitance, oscillation frequency and swing – none of which appear in (1/3)(1/g_mn+1/g_mp). Part of the response to a perturbation on X is also a change of frequency (supply pushing), not just of current. Formally the circuit is now a linear periodically time‑varying system: a small tone at ω on X produces currents at ω ± k·3ω_osc.\n\nSo the quiescent result would only hold if the ring failed to oscillate (per‑stage gain < 2). For an oscillating ring, R_X is different and time‑varying.",
        "format": "markdown",
        "sha256": "4c34f992cda64998113d0d1c38b4fc44fa177d6b86209e9d92dda0fb8504e44b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that oscillation makes the supply current depend on charging the node capacitances, but it does not establish the equivalent resistance or the key conclusion that it remains on the order of the MOS on-resistance. It instead says RX is different and time-varying, and its derivative formula is for conductance, not resistance.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 17276,
        "total_tokens": 20838,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 17276,
        "total_tokens": 20838,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: yes.** The expression is only valid for the quiescent (non‑oscillating) circuit; once the ring oscillates there is no fixed operating point, so a single time‑invariant small‑signal resistance no longer exists, and what the supply \"sees\" is something quite different.\n\n**Why the quiescent answer is correct**\n\nIf the ring does not oscillate (for three identical single‑pole stages this requires a gain per stage below 2), all three nodes settle at the inverter trip point (≈ V_DD/2) with both devices in saturation. Apply a test voltage v_x at the supply: by the rotational symmetry of the ring, every node responds with the same small‑signal voltage v, so for every inverter v_in = v_out. A transistor whose gate and drain move together is, small‑signally, diode‑connected:\n\n- NMOS: current g_mn·v → resistance 1/g_mn from node to ground\n- PMOS: current g_mp·(v_x − v) → resistance 1/g_mp from supply to node\n\nKCL gives v = g_mp v_x/(g_mn+g_mp), the current per inverter is v_x/(1/g_mn+1/g_mp), and with three in parallel\n\nR_X = (1/3)(1/g_mn + 1/g_mp)  (more exactly (1/3)[1/(g_mn+1/r_on) + 1/(g_mp+1/r_op)]).\n\nSo the \"two diodes in series\" picture is right—but only because the trip‑point bias and the symmetric perturbation make v_in = v_out.\n\n**What changes when it oscillates**\n\n- The trip point is an unstable equilibrium that the circuit never stays at. The nodes swing nearly rail‑to‑rail, 120° apart in phase, so each inverter's input and output are large, different, time‑varying voltages. The condition v_in = v_out is gone, and with it the diode‑connected equivalence (the PMOS gate is nowhere near its drain potential).\n- Each transistor cycles through cutoff, triode and saturation; g_m and r_o become periodic functions of time, not constants. The circuit is linear‑periodically‑time‑varying, not LTI, so \"the\" small‑signal resistance is undefined; at best one can talk about an instantaneous (periodically varying) or a time‑averaged quantity.\n- Most of the time one device in each inverter is off, so there is no static path from V_X to ground through that inverter; the supply current consists of pulses that charge the node capacitances (plus brief crowbar current during transitions). The average current is ≈ 3·C_node·V_DD·f_osc + I_sc, i.e. the supply sees essentially a switched‑capacitor‑type load with an effective \"resistance\" ≈ 1/(3 f_osc C_node) that depends on frequency, capacitance and V_DD—not on g_m at the trip point. A perturbation of V_X mainly modulates the frequency and amplitude (supply pushing) rather than being absorbed as a proportional current.\n\n(A DC operating‑point analysis, e.g. SPICE .OP/.TF, would still report the trip‑point value because the trip point remains a mathematical solution of the DC equations—but that number has no physical meaning for the oscillating circuit.)",
        "format": "markdown",
        "sha256": "ce8b437738ca934aa05fc141722edc96b153d50752d615855d289d3e51a25573"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies capacitive charging and gives the effective-resistance expression \\(R_X\\approx 1/(3f_{osc}C_{node})\\), but misses the key conclusion that the oscillation frequency makes this resistance remain on the order of the MOS on-resistance or inverse transconductance. It instead presents the result as unrelated to \\(g_m\\) and substantially different.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 12036,
        "total_tokens": 15598,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3562,
        "output_tokens": 12036,
        "total_tokens": 15598,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It decreases.**\n\nReasoning (amplification phase, right after CK goes high):\n\n- M1–M2 draw a differential current g_m1,2·ΔV_in from nodes P and Q, so the differential voltage grows as  \n ΔV_PQ ≈ (g_m1,2 ΔV_in / C_P)·t.\n- This phase lasts only until V_P and V_Q have fallen by about one threshold (so M3/M4 turn on):  \n t₁ ≈ C_P·V_TH3,4 /(I_SS/2) = 2C_P V_TH3,4 / I_SS.\n- Hence the \"initial\" gain is  \n A_v ≈ 2 g_m1,2 V_TH3,4 / I_SS ≈ 2V_TH3,4 /(V_GS1,2 − V_TH1,2)  (square‑law).\n\nA wider M7 pulls the tail node closer to ground, raising the overdrive of M1/M2 and hence I_SS. Since I_SS grows faster than g_m1,2 (g_m ∝ √I_SS), P and Q discharge faster, M3/M4 turn on sooner, and less differential voltage has built up by then. The gain therefore falls (roughly as 1/√I_SS, or equivalently as the overdrive of M1,2 rises), independent of C_P.\n\nSo widening M7 buys speed (shorter amplification/regeneration time) at the cost of lower initial gain, which makes the offset and noise of M3–M6 more significant when referred to the input. (Once M7 is so wide that it acts as a near‑ideal switch, I_SS becomes limited by M1/M2 themselves and the gain levels off at ≈ 2V_TH3,4/(V_in,CM − V_TH1,2).)",
        "format": "markdown",
        "sha256": "96b12b75e7c1e1da3a364518e165ef8319828bcbb776be2ec3903d936016c4db"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the initial gain decreases and explains that widening M7 raises tail current while input-pair gm grows only sublinearly, reducing the gain factor gm/ICM. The added integration-time explanation is consistent with this trend.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 11694,
        "total_tokens": 16499,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11098,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 11694,
        "total_tokens": 16499,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11098,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It decreases.**\n\n**Why:** In the amplification phase (right after CK goes high), M7 turns on and M1–M2 act as a differential pair discharging the precharged nodes P and Q with tail current I_SS:\n\n- Differential voltage grows as: V_P − V_Q ≈ (g_m1·ΔV_in / C_P)·t\n- This phase lasts until P and Q have fallen by V_TH3 (so M3/M4 turn on): t₁ ≈ 2C_P·V_TH3 / I_SS\n\nSo the gain at the end of this phase is\n\nA_v = (V_P − V_Q)/ΔV_in ≈ 2·g_m1·V_TH3 / I_SS = 2V_TH3 / (V_GS − V_TH)₁,₂  (square-law)\n\nNote the gain is independent of C_P but depends on g_m1/I_SS. Making M7 wider raises I_SS (M7 is in triode with V_GS7 = V_DD, so its current scales with W₇). For a fixed W₁,₂, a larger I_SS raises the overdrive voltage of M1/M2 (g_m1 only grows as √I_SS), so g_m1/I_SS drops and the gain falls. The circuit gets faster (shorter t₁), but at the expense of lower initial gain — i.e., a speed–gain (and hence noise/offset) trade-off.",
        "format": "markdown",
        "sha256": "20b692f1f10d79ec8e1b8a3d3456fed751841f126f8bd174223997993862fad1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the initial gain decreases: a wider M7 raises tail current, while input-pair transconductance grows more slowly, reducing the gain factor gm/ISS. The phase and speed–gain explanation are consistent with the golden solution.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 3305,
        "total_tokens": 8110,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2841,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 3305,
        "total_tokens": 8110,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2841,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It decreases.**\n\nReasoning (StrongARM latch, amplification phase):\n\nWhen CK goes high, M1–M2 act as a differential pair that integrates on the node capacitances at P and Q:\n\nV_P – V_Q ≈ (g_m1,2 ΔV_in / C_P)·t\n\nThis phase lasts until P and Q have dropped by about V_TH3,4 (turning on M3/M4), i.e. for\n\nt ≈ C_P·V_TH3,4 / (I_SS/2)\n\nso the gain at the end of the amplification phase is\n\nA_v = g_m1,2·t/C_P = 2g_m1,2·V_TH3,4 / I_SS = 2V_TH3,4 / (V_GS – V_TH)_1,2\n\nA wider M7 means a larger tail current I_SS. For a fixed input pair, g_m1,2 only grows as √I_SS, so g_m/I_SS falls (the overdrive of M1,2 rises); equivalently, P and Q discharge faster so the integration time shrinks. Thus A_v ∝ 1/√I_SS and the initial voltage gain drops as M7 is made wider (the trade-off being a faster latch).",
        "format": "markdown",
        "sha256": "b9e553915f3793ba6908da17106adbe06d1eacfa191562dcef66af4527e6d496"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the initial gain decreases and explains that a wider M7 raises tail current while input-pair transconductance grows only as the square root of current, reducing the relevant gain factor and integration time.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 4532,
        "total_tokens": 9337,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4134,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4805,
        "output_tokens": 4532,
        "total_tokens": 9337,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4134,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It does not change.**\n\nDuring the amplification phase (after CK goes high and before M₃/M₄ turn on) M₁ and M₂ simply integrate their drain currents on C_P:\n\n- Differential voltage: V_P – V_Q ≈ (g_m1,2 ΔV_in / C_P)·t  \n- Common‑mode drop: P and Q fall at a rate (I_SS/2)/C_P, so M₃ and M₄ turn on (P, Q have dropped by V_TH) at  \n\n  t₁ ≈ C_P·V_TH /(I_SS/2) = 2C_P V_TH / I_SS\n\nThe gain at the end of this phase is therefore\n\nA_v = (g_m1,2/C_P)·t₁ = 2 g_m1,2 V_TH / I_SS = 2V_TH /(V_GS – V_TH)₁,₂\n\nC_P cancels out: a larger capacitance makes the differential voltage grow more slowly, but it also makes P and Q take proportionally longer to fall by V_TH, so M₁–M₂ integrate for a longer time and reach the same differential voltage when M₃/M₄ turn on.\n\nSo increasing the capacitance at P and Q leaves the initial gain (≈2V_TH/(V_GS−V_TH)) unchanged; it only lengthens the amplification phase (slower latch), with the side benefit of lower kT/C‑type input‑referred noise.",
        "format": "markdown",
        "sha256": "71e05f198db956aafc17a0cf8696c4abc2f9b87cfc099e5e8cf164a7e30b3794"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly shows that the larger capacitance slows differential buildup but proportionally extends the amplification phase, so the capacitance cancels and the initial gain is unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 4221,
        "total_tokens": 9027,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3742,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 4221,
        "total_tokens": 9027,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3742,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Nothing – the initial gain stays the same.**\n\nDuring the amplification phase (after CK goes high, before M₃/M₄ turn on) M₁ and M₂ simply integrate their differential current on the capacitances at P and Q:\n\nΔV_PQ(t) = (g_m1,2 ΔV_in / C_P)·t\n\nThis phase lasts until the common‑mode level at P and Q has fallen by V_TH (so that M₃ and M₄ turn on), i.e. for a time\n\nt₁ = C_P·V_TH / (I_SS/2)\n\nHence the gain at the end of the phase is\n\nA_v = g_m1,2·t₁ / C_P = g_m1,2·V_TH /(I_SS/2) = 2V_TH /(V_GS − V_TH)₁,₂\n\nThe C_P cancels: a larger capacitance makes the differential voltage grow more slowly, but it lengthens the integration time by exactly the same factor, so the initial voltage gain is independent of the capacitance at P and Q.\n\nWhat does change is the speed – the amplification phase (and thus the whole decision) takes longer. (As a side benefit, the longer integration averages the noise of M₁,₂ more, so the input‑referred noise of this phase decreases roughly as 1/C_P.)",
        "format": "markdown",
        "sha256": "442200be4eccfb1b61c19ede00284030997b510610a4b87b147084e42c5251c2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correct: the larger capacitance reduces the differential-voltage slope but proportionally extends the amplification phase, so the capacitance cancels from the initial gain. It mainly slows the decision.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 2965,
        "total_tokens": 7771,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2538,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 2965,
        "total_tokens": 7771,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2538,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It stays the same – the amplification‑mode gain is independent of C_P and C_Q.**\n\nReasoning (StrongARM latch, amplification mode):\n\n- When CK goes high, S₁–S₄ open, M₇ turns on, and M₁/M₂ discharge the (precharged‑to‑V_DD) nodes P and Q with currents I_SS/2 ± g_m1,2·ΔV_in/2.\n- The nodes fall at a slope ≈ (I_SS/2)/C_P, and this phase lasts until P and Q have dropped by about V_TH3,4 (M₃, M₄ turn on):\n\n  t₁ ≈ 2C_P·V_TH3,4 / I_SS\n\n- The differential voltage built up at P and Q by the end of this phase is the integrated current difference:\n\n  ΔV_PQ = (g_m1,2·ΔV_in / C_P)·t₁ = (2g_m1,2·V_TH3,4 / I_SS)·ΔV_in\n\nso\n\n  A_v = 2g_m1,2·V_TH3,4 / I_SS ≈ 2V_TH3,4 / (V_GS − V_TH)₁,₂\n\nC_P cancels: a larger capacitance makes the nodes slew more slowly, but the amplification phase lasts proportionally longer, so M₁/M₂ integrate their differential current for a longer time and the resulting ΔV_PQ is unchanged.\n\nWhat does change: the comparator becomes slower (longer t₁ and overall decision time), while the longer integration window reduces the input‑referred noise (roughly ∝ 1/C_P). So adding capacitance at P and Q trades speed for noise, not gain.",
        "format": "markdown",
        "sha256": "a9e516e5653a98257f786b7ec9c6c7124c1a055a03830f15a89dd1002b1172ff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes the initial gain is unchanged and shows that the capacitance cancels: larger capacitance slows the node discharge but proportionally lengthens the amplification phase. The added speed/noise comments are secondary.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 4432,
        "total_tokens": 9238,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3864,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4806,
        "output_tokens": 4432,
        "total_tokens": 9238,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3864,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It degrades (or at best does not help).**\n\nReason – look at when M5/M6 actually do anything:\n\n1. After CK goes high, M1/M2 discharge P and Q. Only when P, Q have dropped by V_THN do M3/M4 turn on and start discharging X and Y.\n2. M5/M6 stay off until X and Y have fallen by |V_THP|. Up to that point the only regeneration is the weak NMOS loop (τ ≈ C_X/g_m3,4).\n3. Only after that do M5/M6 add their transconductance, giving τ_reg ≈ C_X/(g_m3 + g_m5).\n\nMaking M5 and M6 wider directly increases C_X and C_Y (gate capacitance of the cross‑coupled PMOS plus their drain junction/overlap capacitance). Consequences:\n\n- The time for X, Y to drop by |V_THP|, Δt ≈ C_X·|V_THP|/(I_SS/2), grows in proportion to the added capacitance – the PMOS pair turns on later, and the NMOS‑only regeneration during that interval is also slower because C_X/g_m3 is larger.\n- During the final regeneration the larger g_m5 is largely offset by the larger C_X: τ_reg = (C_0 + ΔC)/(g_m3 + g_m5), and since the PMOS g_m/C (low mobility) is not better than the g_m/C already present at X, the improvement is marginal, approaching at best the PMOS 1/ω_T.\n\nSo the unambiguous penalty (later onset of regeneration, slower discharge of X/Y) outweighs the marginal benefit, and the total decision time increases. This is why in the StrongARM latch M5/M6 are kept relatively small (no larger than M3/M4): their job is mainly to pull the \"high\" output back to V_DD (full logic levels, no static current), not to provide the regenerative gain, which comes from M3/M4 driven by the tail current.",
        "format": "markdown",
        "sha256": "27fbd0d3f1cd948772ff31aa01f856d8ea6bb6195d1dc6f300661c8ec91ec6c1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The answer recognizes that wider M5/M6 increase capacitance and also increase transconductance, but incorrectly concludes that the capacitance dominates from the outset. The golden solution says the stronger PMOS regeneration initially wins, with parasitic capacitance limiting the benefit only at larger widths.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 9626,
        "total_tokens": 14428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8972,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 9626,
        "total_tokens": 14428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8972,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It degrades (or at best does not improve).** The intuitive expectation – \"more g<sub>m</sub> in the cross‑coupled inverters, so faster regeneration\" – does not hold up for M<sub>5</sub> and M<sub>6</sub>, for two reasons:\n\n**1. M<sub>5</sub> and M<sub>6</sub> are off during the phases that matter most.**\nAfter CK rises, P and Q fall first, then M<sub>3</sub>/M<sub>4</sub> turn on and X and Y start to discharge. M<sub>5</sub> and M<sub>6</sub> (sources at V<sub>DD</sub>, gates at X and Y ≈ V<sub>DD</sub>) stay off until X and Y have dropped by |V<sub>THP</sub>|. During this entire amplification interval they contribute nothing but capacitance to X and Y: the drain junction of M<sub>5</sub> and the gate of M<sub>6</sub> load X, and vice versa. A wider PMOS pair therefore raises C<sub>X</sub>, C<sub>Y</sub>, slows the fall of X and Y (dV/dt ≈ I<sub>SS</sub>/2C<sub>X</sub>), and delays the onset of regeneration.\n\n**2. In regeneration, the extra g<sub>m</sub> is cancelled by the extra capacitance.**\nThe regeneration time constant is roughly τ<sub>reg</sub> ≈ C<sub>X</sub>/(g<sub>m3</sub> + g<sub>m5</sub>). Both g<sub>m5</sub> and the PMOS contribution to C<sub>X</sub> scale with W<sub>5,6</sub>, so τ<sub>reg</sub> simply moves toward the PMOS's own g<sub>m</sub>/C ratio (~1/ω<sub>T,p</sub>). Because the PMOS has lower mobility, this ratio is no better than what the node already has, so τ<sub>reg</sub> hardly improves—and with large widths it gets worse. Moreover, right when regeneration begins the PMOS overdrive is nearly zero, so g<sub>m5,6</sub> is small anyway, while the capacitance penalty is fully present.\n\n**Net effect:** the total decision time (amplification + regeneration) increases. M<sub>5</sub> and M<sub>6</sub> should be sized only large enough to pull the winning output to V<sub>DD</sub> and guarantee zero static current; the latch speed is set by the tail current, M<sub>1</sub>–M<sub>4</sub>, and the capacitance at X and Y.",
        "format": "markdown",
        "sha256": "094db038fda98bec0970bb314dac00b40e15ee9fed4a56aca5e5aea9f15ebd9c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer reaches the opposite of the key result: widening M5/M6 initially improves speed because stronger regeneration dominates the added capacitance. It identifies capacitance as a real eventual limitation, but incorrectly treats it as dominant from the outset.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 26482,
        "total_tokens": 31284,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25590,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 26482,
        "total_tokens": 31284,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25590,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It degrades (or at best does not improve).**\n\nReasoning, following the latch's phases after CK goes high:\n\n1. **Amplification / M3‑M4 turn‑on.** M1, M2 discharge P and Q; after P, Q drop by V_THN, M3 and M4 turn on and X and Y begin to fall. During this entire interval M5 and M6 are **off** (they conduct only after X and Y have fallen by |V_THP|). All they contribute is capacitance: C_X and C_Y contain C_DB + C_GD of M5/M6 and the gate capacitance of M6/M5 (cross‑coupled). The time for X, Y to drop by |V_THP| is roughly C_X·|V_THP|/(I_SS/2), so wider PMOS devices lengthen this \"dead\" interval directly, and they also slow the NMOS‑only regeneration (τ ≈ C_X/g_m3) that occurs during it.\n\n2. **Regeneration.** Once M5, M6 turn on, the time constant is τ_reg ≈ C_X/(g_m3 + g_m5). One might think a larger g_m5 helps, but g_m5 and the PMOS share of C_X scale together with W; the ratio is bounded by the PMOS gm/C (its f_T), which is low because PMOS mobility is low and because M5/M6 have almost no overdrive when regeneration starts. So the gain in g_mP is largely cancelled by the added capacitance, while the NMOS term is penalized by it.\n\nThe total delay (t₁ + t₂ + τ_reg·ln(…)) therefore gets longer: the pre‑regeneration phases slow down linearly with the PMOS width and regeneration gains little or nothing. This is why M5 and M6 are usually kept small—just strong enough to pull the \"high\" output back to V_DD—rather than sized up for speed.",
        "format": "markdown",
        "sha256": "fc60f1182f9b2e1d4939da458ebcc8a294cce0c0936f7688611bd04ad60d77b1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that wider M5/M6 increase regenerative transconductance while adding node capacitance, but incorrectly concludes the capacitance dominates initially and speed degrades. The expected trend is initial speed improvement, with parasitics limiting the benefit at larger widths.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 10052,
        "total_tokens": 14854,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9430,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 4802,
        "output_tokens": 10052,
        "total_tokens": 14854,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9430,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** not much better, and fairly soon worse. Widening the clocked devices gives at best a small, saturating gain in drive, while the capacitance they add – at X and Y, at the internal nodes, and on the clock – grows linearly. Beyond a modest size the speed degrades.\n\n**Why**\n\n1. *What happens at a clock edge.* With CK high the left clocked inverter is transparent (X = Z̄) and the right one is off (Y just floats); with CK low the roles reverse (Y = X̄, Z = Ȳ). Because Z (or X) has already settled before the clock edge, every transition at X or Y is initiated by the clock: the input device (e.g., M1) is already on and has already pulled the internal node to the rail, and it is the clocked device, sitting between the internal node and the output, that turns on and carries the charging/discharging current (it starts in saturation; M1 is only a triode \"degeneration\" resistor in series with it).\n\n2. *Benefit of a wider clocked device.* Lower series resistance / more current in the path that charges or discharges X and Y. But the benefit is bounded: the input device stays in series, so even an infinitely wide clocked transistor can at most halve the path resistance.\n\n3. *Costs, all proportional to width.*\n   - The clocked devices are the ones adjacent to X and Y, so their drain‑junction and gate–drain overlap capacitances land directly on C_X and C_Y (which otherwise consist mainly of the next stage's gate capacitance / Inv3's input). Their source junctions enlarge the internal nodes, and the internal node on the \"off\" side is also dragged along with the output through the on clocked device of the opposite polarity, so it must be charged/discharged too. The RC product therefore falls only slightly, reaches a shallow minimum when the clocked devices are roughly equal to or somewhat wider than the input devices (≈ W_in·√(C_L/C_d)), and then rises.\n   - CK and CK̄ see the gate capacitance of all four clocked transistors. A heavier clock load means a larger, more power‑hungry clock buffer; if the buffer is not scaled up, the clock edges slow down, which directly slows these clock‑initiated transitions and lengthens the interval during which both latches are partly transparent (race, clock feedthrough and charge injection onto the floating nodes X and Y).\n\n**Conclusion:** a small increase buys a marginal improvement; making the clocked transistors \"wide\" degrades the speed (and always costs clock power). They should be sized comparable to, not much larger than, the input transistors.",
        "format": "markdown",
        "sha256": "edc256bda45bfa836d3cc635278317a8d30500088fb78dde58dca01034c72937"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It says widening initially improves speed by lowering the clocked devices’ series resistance, while added capacitance eventually limits or reverses the benefit. This matches the golden solution’s full-credit rule.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 26664,
        "total_tokens": 28886,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 26664,
        "total_tokens": 28886,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: it degrades (beyond a modest size the circuit gets slower, not faster).**\n\nWhy:\n\n1. **How the stage switches.** This is a C²MOS (clocked‑CMOS) dynamic ÷2: when CK is high the first stage is transparent (X = Z̄) and the second holds; when CK is low the second is transparent (Y = X̄) and the first holds; Z = Ȳ. The data input of each stage (Z or X) has settled *before* the clock edge, so the data transistor (M1 or the top PMOS) is already on and has already pre‑discharged/pre‑charged the internal node. The clocked transistor is the device that actually turns on at the clock edge, and X (or Y) then charges/discharges through the series pair \"clocked device + data device.\"\n\n2. **Diminishing return in current.** Two series MOSFETs with their gates at the rail behave like a single transistor with  \n (W/L)eq = 1 / [(L/W)clk + (L/W)data].  \n The current is therefore bounded by the data transistor: doubling the clocked‑device width raises the current only ~33 %, and even an infinitely wide clocked device only doubles it. The clocked transistors are essentially switches; once they are comparable in width to the data devices, widening them buys very little drive.\n\n3. **Linear increase in capacitance where it hurts most.** The clocked transistors sit right at the output nodes, so their drain‑junction and gate–drain overlap capacitances add directly to C_X and C_Y – the critical nodes of the loop – and this capacitance grows linearly with width. In addition, four clocked gates load the clock (CK and CK̄) lines; slower clock edges from the VCO buffer directly delay the turn‑on of the very devices that initiate the transition (and raise clock power and clock feedthrough).\n\nNet result: the delay ∝ C_node/I_eq has a shallow optimum roughly where the clocked devices are about the same size as the data devices; making them wider than that increases C_X, C_Y and the clock load faster than it increases the charging current, so the maximum operating frequency drops. If more speed is needed, it is the data transistors (and the node/clock loading) that should be addressed, not wider clocked switches.",
        "format": "markdown",
        "sha256": "52094de9e6d9107cf525508d92b295b88f053a1713516bd476f05fb3d1f1abe6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It identifies a finite optimum: widening lowers the clocked devices’ series resistance and increases drive up to that point, while added capacitance at X and Y eventually limits or reverses the benefit. Its claim that further widening slows the circuit is consistent with the stated optimum.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 42110,
        "total_tokens": 44332,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41372,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 42110,
        "total_tokens": 44332,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41372,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: not monotonically – it helps only up to a point and then hurts.**\n\nReasoning:\n\n1. **Where the clocked devices sit.** In each C²MOS latch the clocked PMOS/NMOS are stacked in series with the input devices and are the transistors *adjacent to the output node* (X or Y). When the latch is transparent they conduct with V_GS ≈ V_DD, so the delay of the latch is roughly\n\n t ≈ (R_on,input + R_on,clk) · C_X,\n\n where C_X = (drain‑junction + overlap capacitance of the two clocked devices) + (gate capacitance of the next stage) + wiring.\n\n2. **Benefit of widening them.** R_on,clk ∝ 1/W_clk, so the pull‑up/pull‑down path to X and Y becomes stronger – this is why one may be tempted to make them wider than the input devices (they also suffer from body effect and a slightly reduced overdrive, since their sources are not at the rails).\n\n3. **Penalties of widening them.**\n - Their drain capacitance sits directly on X and Y (and on the internal nodes), so C_X grows in proportion to W_clk.\n - Once R_on,clk ≪ R_on,input, the current is limited by the input transistors (M1 and its PMOS partner) anyway, so the resistance stops improving while the capacitance keeps increasing.\n - Their gates load CK and CK̄; for a given clock buffer the clock edges become slower (or the buffer must burn more power), and clock feedthrough to X and Y also increases.\n\n4. **Net result.** The delay (R_in + a/W_clk)(C₀ + bW_clk) has a minimum. Increasing the clocked‑transistor widths improves the speed only while their on‑resistance is a significant part of the total series resistance (roughly up to widths comparable with, or somewhat larger than, the input devices); beyond that the added capacitance at X, Y and on the clock lines dominates and the speed *degrades*. In practice the clocked devices are therefore made about the same size as (or modestly wider than) the input transistors rather than arbitrarily wide.",
        "format": "markdown",
        "sha256": "564412fc4a27715d0aeca830843dc3cba60957d755651c1fda3b81919bd2e82e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that widening the clocked transistors initially improves speed by reducing their on-resistance, while added capacitance at the latch nodes eventually limits or reverses the benefit, giving an optimum width.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 18720,
        "total_tokens": 20942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18006,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2222,
        "output_tokens": 18720,
        "total_tokens": 20942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18006,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes – nodes X and Y are in quadrature.**\n\nReasoning:\n\n1. The circuit is a master‑slave divider built from two C²MOS (clocked) inverters and a static inverter (Inv₃):\n   - First stage: the clock devices (PMOS on $\\overline{CK}$, NMOS on $CK$) are both on when **CK = 1**, so $X=\\overline{Z}$; when CK = 0 both are off and X is held dynamically.\n   - Second stage: its clock devices are on when **CK = 0**, so $Y=\\overline{X}$; when CK = 1, Y is held.\n   - $Z=\\overline{Y}$ at all times.\n\n2. The loop contains two latches and three inversions, so it toggles – a ÷2. Following the timing:\n   - At a rising edge of CK: $X=\\overline{Z}=Y$ (X takes the current value of Y).\n   - At the following falling edge: $Y=\\overline{X}$, i.e., Y toggles (and so does Z).\n   - At the next rising edge X toggles, etc.\n\n   Hence X changes only on the rising edges of CK and Y (and Z) only on the falling edges. Both have period $2T_{CK}$ and 50 % duty cycle, and they are displaced by $T_{CK}/2$, which is one quarter of the output period, i.e., 90°. X is the \"master\" output and Y the \"slave\" output, exactly as in a conventional master‑slave divider: Y (0°), X (90°, lagging), Z = $\\overline{Y}$ (180°). The 270° phase ($\\overline{X}$) is not directly available and would need one more inverter (matched to Inv₃).\n\nCaveats: since X is set by the rising edge and Y by the falling edge, the 90° relationship is exact only for a 50 % duty‑cycle clock and well‑matched CK/$\\overline{CK}$ (an inverter‑generated $\\overline{CK}$ introduces skew), and the different loads seen by X and Y add some phase error. Also, X and Y are dynamic nodes that float during their hold phases.",
        "format": "markdown",
        "sha256": "fc794361759a3719b9797c3e996ca19558d61c0c0107af160dd507f567294c71"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies nominal divide-by-two quadrature and notes unequal loading can cause phase error. It omits the distinct Inv₃ propagation delay that skews Z, so it does not meet the full-credit rule.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 12936,
        "total_tokens": 15139,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12241,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 12936,
        "total_tokens": 15139,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12241,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes – nodes X and Y are (nominally) in quadrature.**\n\n**Why:**\n\n- Each stack is a clocked‑CMOS (C²MOS) inverter/latch. The first stage has its clock devices driven by CK̄ (PMOS) and CK (NMOS), so it is transparent only when CK is high (X = Z̄) and holds X (floating node) when CK is low.\n- The second stage has its clock devices driven by CK (PMOS) and CK̄ (NMOS), so it is transparent only when CK is low (Y = X̄) and holds Y when CK is high.\n- With Inv₃ closing the loop (Z = Ȳ), the two latches form a master–slave toggle flip‑flop, i.e. a ÷2 circuit.\n\nTracing the states: when CK goes high, X takes the value Z̄ = Y, so X toggles on the **rising** edge of CK; when CK goes low, Y takes X̄, so Y toggles on the **falling** edge of CK. Both X and Y therefore run at f_CK/2 with 50 % duty cycle, and their transitions are displaced by T_CK/2 – which is one quarter of the output period (2T_CK), i.e. 90°. Z is simply the complement of Y (delayed by one inverter), so the circuit gives roughly 0°, 90° and 270° phases.\n\n**Caveats:** the 90° relationship holds only if CK has a 50 % duty cycle and CK/CK̄ are truly complementary (no skew); X and Y see different loads (X drives two gates of the second latch, Y drives Inv₃), the nodes are dynamic (floating during hold), and Z lags Y by an inverter delay. So the phases are single‑ended and only approximately quadrature; buffering/load balancing (and another inverter for X̄) are needed for accurate I/Q outputs.",
        "format": "markdown",
        "sha256": "41ecf78b1c0716c12f43e689de0e17b92e4b19cbc33ed20ba43a7b5996569dab"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies nominal divide-by-two quadrature from the latches switching on opposite clock phases, and explains both key departures from exact quadrature: unequal latch loading and Inv3 delay skewing Z. The additional caveats do not undermine the answer.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 11904,
        "total_tokens": 14107,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11284,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 11904,
        "total_tokens": 14107,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11284,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes – X and Y (and Z) are in quadrature.**\n\nReasoning:\n\n- The left C²MOS stage (clocked by CK on the NMOS and CK̄ on the PMOS) is transparent when CK is **high**, giving X = Z̄; when CK is low, X floats and holds its value.\n- The right stage (clocked by CK̄ on the NMOS and CK on the PMOS) is transparent when CK is **low**, giving Y = X̄; when CK is high, Y holds.\n- Inv₃ provides the third inversion in the loop (Z = Ȳ) so that the loop has net negative feedback and toggles.\n\nFollow the loop: at a rising edge of CK, X takes the value Z̄; at the next falling edge Y becomes X̄ (and Z becomes Ȳ); at the next rising edge X becomes Z̄ again – i.e. the opposite of what it was. Thus\n\n- X changes state **only on rising edges** of CK,\n- Y (and Z) change state **only on falling edges** of CK,\n\neach with a period of 2T_CK (divide‑by‑2). The transitions of X and Y are therefore separated by T_CK/2, which is one‑quarter of the output period, i.e. 90°. Exactly as in a master–slave CML divider, the first‑latch output and the second‑latch output are quadrature phases: X ≈ 0°, Z ≈ 90°, Y ≈ 270° (Z = Ȳ, apart from the Inv₃ delay); an extra inverter on X would supply the fourth phase.\n\nCaveats: the 90° relationship assumes a 50 % duty‑cycle input clock and identical (equally loaded) latches; Z is Ȳ only to within the delay of Inv₃, and at the very highest speeds the Inv₃ delay in the Z→X path can skew X slightly relative to Y.",
        "format": "markdown",
        "sha256": "0358c30480c94e5c0bef15183a95fef15b23fb0f4294cde5f85a61d810cd09e0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies nominal divide-by-two quadrature and the skew from Inv3 delay. It only states equal loading as an assumption, though, rather than identifying unequal latch loading as a cause of phase error.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 11796,
        "total_tokens": 13999,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11173,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2203,
        "output_tokens": 11796,
        "total_tokens": 13999,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11173,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: it improves – but only up to a point, and the price is paid by the clock.**\n\n**Why it improves**\n\n- In each C²MOS stage the clocked transistor is in series with the data transistor in every pull‑up and pull‑down path. Its on‑resistance therefore adds directly to the stage delay (roughly T_D ≈ (R_data + R_clk)·C_out). Widening the clocked devices lowers R_clk and hence the delay (it also reduces the source voltage, i.e. the body effect/degeneration, of the data devices, giving them more current).\n- In this particular topology the clocked devices are placed next to the supply rails, not next to the output. Their larger drain junction capacitance therefore appears at the internal nodes (between clocked and data devices), not at the output node or at the gates of the next stage. The capacitance in the signal path is essentially unchanged, so the gain in drive is not cancelled by extra load as it would be if the data transistors were widened (widening those adds capacitance to both the previous stage's output and the present output).\n- The internal‑node capacitance only redistributes charge that is already on the output node (charge sharing when the stage is opaque), so the total charge the stack must remove is unchanged while the available current is larger.\n\n**Why the benefit is limited**\n\n- Diminishing returns: once R_clk ≪ R_data the stage behaves like a plain inverter formed by the data devices; if all devices started with equal widths the maximum gain is only about 2×.\n- Meanwhile the gate capacitance presented to CK and CK̄ grows linearly: more power in the clock buffer (or heavier loading of the VCO), slower clock edges (which delay the instants at which stages become transparent/opaque and aggravate CK/CK̄ overlap), more clock feedthrough, and larger charge sharing between the internal nodes and the floating output in the hold mode (glitches, reduced margin).\n\nSo modestly wider clocked transistors speed the divider up; making them very wide buys no further speed and, for a given clock driver, eventually slows the circuit and wastes power.",
        "format": "markdown",
        "sha256": "d736c95117bee6b33a1863fdb97038e208cbcecd1c7f16a50f602d848977f96b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that widening the clocked devices improves speed by reducing series resistance with little added output loading, and identifies charge sharing as a limit on the benefit rather than making the topology unusable.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 26993,
        "total_tokens": 29278,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26310,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 26993,
        "total_tokens": 29278,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26310,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer: it helps only up to a point – the latch itself gets faster, but the clock gets loaded, so beyond an optimum width the overall speed degrades.**\n\n**Why the latch gets faster**\n\n- In this C²MOS ÷2 the clocked devices are the *outer* transistors (sources at V_DD/ground). Their drains tie to the internal nodes, not to the latch outputs, so widening them does **not** add capacitance to the output nodes X (and Y) that must be charged/discharged.\n- In this divider the input of each latch has already settled while the latch is in hold (Q changes during stage 1's hold, X changes during stage 2's hold). Thus every output transition is initiated by the clock edge turning on a clocked device, and the output is charged/discharged through the series combination R_on,clk + R_on,data. Increasing W_clk lowers R_on,clk and shortens this clock‑to‑output delay, which (together with the feedback inverter delay) is what sets f_max ≈ 1/(2·t_delay).\n- The added drain capacitance at the internal node only contributes a width‑independent term (R_on,clk·C_drain,clk ≈ constant), so the delay decreases monotonically but with diminishing returns, approaching that of a plain inverter made of the data devices.\n\n**Why it eventually hurts**\n\n- The gate capacitance presented to CK and CK̄ grows linearly with W_clk. This loads the VCO (or clock buffer): the clock edges slow down (and it is precisely these edges that trigger the transitions), the VCO frequency/tuning range drops, and clock‑path power rises.\n- The larger internal‑node capacitance worsens charge sharing when the input changes during the hold mode (which happens every half cycle here), disturbing the floating output and eroding noise margin.\n\n**Net result:** with an ideal clock the speed improves (saturating); with a realistic clock driver there is an optimum – clocked devices modestly wider than the data devices – and making them wider than that degrades the divider's speed.",
        "format": "markdown",
        "sha256": "31b78683caf57a1a873d512cdb4812c5ca660807b5124554ebb79600f18bf71a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly says widening initially improves speed by reducing series on-resistance while adding little output loading, and identifies increased charge sharing as a width-related limitation. Its possible large-width slowdown from clock loading is allowed by the golden solution’s full-credit rule.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 20247,
        "total_tokens": 22532,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19577,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 20247,
        "total_tokens": 22532,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19577,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** it improves – up to a point. Making the clocked devices wider lowers the series resistance in the charge/discharge path without adding capacitance to the signal (output) nodes, so the latch delay falls; the price is paid on the clock lines, not in the signal path. The gain saturates, and if the devices are made very wide the extra clock load and charge sharing start to hurt.\n\n**Why**\n\n1. *What the circuit does.* The two stages are C²MOS (clocked‑inverter) latches in a master/slave arrangement with inverting feedback, i.e. a ÷2 (toggle) circuit. The master is transparent when CK is high, the slave when CK is low, and each output simply floats when its latch is in hold.\n\n2. *Where the clocked transistors sit in the critical path.* In steady ÷2 operation the data input of each latch is produced by the *other* latch while this latch is in hold. So when a latch's clock edge arrives, its data transistor is already on and the output transition is launched by the clocked transistor turning on. The clock‑to‑output delay is therefore set by the series combination (clocked device + data device) driving the output node:\n\n τ ≈ R_clk(C_int + C_out) + R_data·C_out\n\n where C_out is the output capacitance (drains of the data devices + gates of the next stage) and C_int is the capacitance of the internal node between the clocked and data devices.\n\n3. *Effect of widening the clocked devices.* R_clk ∝ 1/W_clk. Because the clocked transistors are placed next to the rails, their drain junctions land on the internal nodes, not on the outputs, so C_out does not change; only C_int grows (C_int = C₀ + c·W_clk). Substituting,\n\n τ ≈ ρ(C₀ + C_out)/W_clk + ρc + R_data·C_out,\n\n which decreases monotonically with W_clk and approaches the delay of the data transistor alone. Hence the divider gets faster, with diminishing returns once R_clk ≪ R_data.\n\n4. *What eventually limits it.* \n – Clock loading: each clock phase drives one PMOS and one NMOS per latch; their gate capacitance grows with W_clk, so either the clock edges slow down (delaying turn‑on) or the clock buffers must be enlarged (more power). \n – Charge sharing: in hold the output floats; when the input changes and turns on a data device, the internal node (sitting at a rail) dumps charge ≈ VDD·C_int/(C_int + C_out) onto the stored output, disturbing the level the other (transparent) latch is reading. This disturbance grows with W_clk. \n – More clock feedthrough.\n\nSo the speed improves as the clocked transistors are widened, but only until their on‑resistance is a small fraction of the data devices'; beyond that the added clock capacitance and charge sharing dominate, and an optimum (clocked devices comparable to or moderately wider than the data devices) exists.",
        "format": "markdown",
        "sha256": "f0aa88e45bc2ca3e2f1f95cc9cf635576080df0243d59dc992fa21697d2e8f3e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that widening the clocked transistors improves speed by reducing their series resistance while adding little output loading, and identifies charge sharing as a limit on further improvement.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 23086,
        "total_tokens": 25371,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22102,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2285,
        "output_tokens": 23086,
        "total_tokens": 25371,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22102,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## What the circuit looks like vs. what it actually is\n\nAt first glance this is a three‑inverter ring (odd number of inversions → it would oscillate if the loop were closed). But the two switches are driven by **complementary** clocks:\n\n* CK = 1 → switch S1 (before Inv₁) is on, switch S2 (after Inv₁) is off\n* CK = 0 → S1 off, S2 on\n\nSo at any instant exactly one switch is open and **the loop is never closed**. The circuit therefore cannot oscillate on its own. Instead, the two inverter inputs that sit behind a switch become *dynamic storage nodes* (voltage held on gate capacitance), and the ring becomes a clocked, sampled‑data feedback loop:\n\n* S1 + Inv₁ = dynamic latch, transparent while CK = 1 (master)\n* S2 + Inv₂ = dynamic latch, transparent while CK = 0 (slave)\n* Inv₃ returns the complement of the slave output to the master input.\n\nThat is a master‑slave D flip‑flop with D = Q̄, i.e. a toggle flip‑flop → a **dynamic divide‑by‑2 circuit**.\n\n## Step‑by‑step operation\n\nLabel the nodes: A = input of Inv₁, B = output of Inv₁, C = input of Inv₂, D = output of Inv₂, E = output of Inv₃ (fed back to S1).\n\n* **CK = 1:** S1 closed, S2 open. A = E, B = Ā. Node C floats and keeps its old value, so D and E do not change.\n* **CK = 0:** S1 open, S2 closed. A floats and keeps its value; C = B = Ā, hence D = A, E = Ā.\n* **Next CK = 1:** A = E = complement of the previous A.\n\n| Interval | A | B | C | D | E |\n|---|---|---|---|---|---|\n| CK=1 (cycle n) | 0 | 1 | 0 (held) | 1 | 0 |\n| CK=0 | 0 (held) | 1 | 1 | 0 | 1 |\n| CK=1 (cycle n+1) | 1 | 0 | 1 (held) | 0 | 1 |\n| CK=0 | 1 (held) | 0 | 0 | 1 | 0 |\n| CK=1 (cycle n+2) | 0 | 1 | 0 (held) | 1 | 0 |\n\nThus A[n+1] = NOT A[n]: every node changes state once per clock period, so **all nodes are square waves at f_CK/2**:\n\n```\nCK  ‾‾‾‾‾‾______‾‾‾‾‾‾______‾‾‾‾‾‾______‾‾‾‾‾‾______\nA   ____________‾‾‾‾‾‾‾‾‾‾‾‾____________‾‾‾‾‾‾‾‾‾‾‾‾   (toggles on CK rising edges)\nE   ______‾‾‾‾‾‾‾‾‾‾‾‾____________‾‾‾‾‾‾‾‾‾‾‾‾______   (toggles on CK falling edges)\n```\n\n## Properties\n\n* Output frequency exactly f_CK/2; duty cycle is 50 % regardless of the clock duty cycle (each node toggles on only one type of edge).\n* A/B switch on rising edges, C/D/E on falling edges; the two groups are offset by T_CK/2 = one quarter of the output period → **quadrature outputs** for free (exact if CK has 50 % duty cycle): A (0°), E (90°), B (180°), D (270°).\n* No static power, rail‑to‑rail swing, no stuck/forbidden state (any initial condition toggles), only 8–10 transistors, and the clock sees just one small switch gate per phase (low clock loading → high speed).\n* The clock does not “tune” an oscillator; unlike an injection‑locked divider there is no locking range – the division ratio is exactly 2 for any f_CK within the limits below.\n\n## Limitations / design constraints\n\n1. **Maximum clock frequency.** During CK = 0 the data must get through S2, Inv₂ and Inv₃ before S1 closes again; during CK = 1 through S1 and Inv₁ before S2 closes:\n   T_CK/2 ≳ max(t_S1 + t_Inv1, t_S2 + t_Inv2 + t_Inv3) ⇒ f_CK,max ≈ 1/[2(t_sw + 2t_inv)].\n   (Placing S2 between Inv₂ and Inv₃ balances the two phases and raises the limit somewhat.) For comparison, the same three inverters as a free‑running ring would oscillate at ≈1/(6t_inv).\n2. **Minimum clock frequency.** Nodes A and C are floating half of the time; leakage slowly destroys the stored level, so the divider fails if the clock is too slow and the circuit cannot be tested statically.\n3. **Clock overlap / race.** If CK and CK̄ are both high for a while (e.g., CK̄ made from CK with an inverter), both switches conduct, the ring is momentarily closed and the new value at A can race through Inv₁ into C (and around the loop). The overlap must be shorter than t_S1 + t_Inv1; well‑matched complementary (or non‑overlapping, which is harmless here) clocks are needed.\n4. **Switch non‑idealities.** Charge injection and clock feedthrough disturb A and C; single‑NMOS switches pass only V_DD − V_TH, slowing the next inverter and causing static current → use transmission gates.\n\n## Remarks\n\n* The odd number of inverters is essential: with two (any even number) the loop would merely hold its state – a dynamic latch – and never toggle. Inv₃ supplies the Q̄→D inversion.\n* With both switches permanently on the circuit reverts to a 3‑stage ring oscillator.\n* Cascading n such stages gives a ÷2ⁿ prescaler.",
        "format": "markdown",
        "sha256": "35c22e045184bf19ee4458b4b7fb1da30d3d65f032c4ef9e813535e7ddb04956"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the arrangement as a dynamic-latch master-slave divide-by-two circuit; the additional operating explanation is consistent with the essential answer.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 17941,
        "total_tokens": 19374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 17941,
        "total_tokens": 19374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\nTopologically this is a three‑stage ring oscillator (three inversions around the loop), but the loop is cut in two places by switches driven by complementary clock phases. Since S₁ (CK) and S₂ (CK̄) are never closed at the same time, the loop is never actually closed, so the circuit cannot free‑run. Instead it is a *clocked* circuit:\n\n- A switch followed by an inverter is a **dynamic latch**: with the switch on, the inverter output follows the (inverted) input (\"sense\"); with the switch off, the voltage is held on the gate capacitance of the inverter (\"hold\").\n- S₁–Inv₁ is a latch transparent when CK = 1 (master), S₂–Inv₂ is a latch transparent when CK = 0 (slave). Together they form a negative‑edge‑triggered flip‑flop.\n- Inv₃ supplies the extra inversion in the feedback path, i.e. D = Q̄.\n\nA flip‑flop with D = Q̄ is a toggle flip‑flop, so the arrangement is a **dynamic ÷2 circuit (frequency divider)**.\n\n**Step‑by‑step operation**\n\nLabel the nodes: A = input of Inv₁, B = output of Inv₁, X = input of Inv₂, Y = output of Inv₂, Z = output of Inv₃ (fed back to S₁). Suppose that while CK is high node X holds some logic value X₀.\n\n| Half cycle | CK | S₁ | S₂ | A | B | X | Y | Z |\n|---|---|---|---|---|---|---|---|---|\n| 1 | 1 | on | off | X₀ (=Z) | X̄₀ | X₀ (held) | X̄₀ | X₀ |\n| 2 | 0 | off | on | X₀ (held) | X̄₀ | X̄₀ (=B) | X₀ | X̄₀ |\n| 3 | 1 | on | off | X̄₀ (=Z) | X₀ | X̄₀ (held) | X₀ | X̄₀ |\n| 4 | 0 | off | on | X̄₀ (held) | X₀ | X₀ (=B) | X̄₀ | X₀ |\n| 5 | 1 | on | off | X₀ | X̄₀ | X₀ | X̄₀ | X₀ → same as 1 |\n\n- Node B (Inv₁ output) changes once on every **rising** edge of CK.\n- Nodes X, Y, Z change once on every **falling** edge of CK.\n- The state repeats after four half cycles, i.e. after 2T_CK.\n\nHence every node runs at **f_CK/2**. Because each output toggles on every edge of the same polarity, the output duty cycle is exactly 50 % regardless of the CK duty cycle. Moreover, B toggles on rising edges and Y/Z on falling edges, so with a 50 % clock the outputs are in **quadrature**: B (0°), Z (90°), A ≈ B̄ (180°), Y (270°) – the usual I/Q property of a ÷2 stage.\n\n**Why three inverters?**\n\nWith only two inversions in the loop (no Inv₃), the stored value would simply be recirculated each cycle and nothing would toggle. The odd number of inversions is what makes a ring \"want\" to oscillate; the switches merely dictate *when* each node may change. The signal needs one half cycle to get through S₁/Inv₁ and the other half cycle to get through S₂/Inv₂/Inv₃, so one complete trip around the loop (which inverts every node) takes T_CK, and a full output period takes 2T_CK. One can view it as a ring oscillator whose stage delays are forced by the clock to T_CK/2 – an oscillator locked at exactly half the clock frequency.\n\n**Speed limit and practical issues**\n\n- While CK = 1, Z must propagate through S₁ and Inv₁ before CK falls; while CK = 0, B must propagate through S₂, Inv₂ and Inv₃ before CK rises. With 50 % duty cycle: T_CK/2 ≥ t_sw + t_Inv2 + t_Inv3, so f_CK,max ≈ 1/[2(t_Inv2 + t_Inv3 + t_sw)] ≈ 1/(4t_d) for equal delays (output ≈ 1/(8t_d)). Note that the same three inverters as a free‑running ring would oscillate at 1/(6t_d), i.e. the divider is slower than the ring made of the same gates.\n- The circuit is dynamic: nodes A and X store charge on parasitic capacitances, so leakage sets a **minimum** clock frequency and the clock cannot be stopped. Charge injection and clock feedthrough of the switches disturb the held levels (tolerable as long as the inverter thresholds are not crossed).\n- CK and CK̄ must not overlap such that both switches are momentarily on; otherwise the loop closes and the state can race around it (the circuit briefly behaves like a 3‑stage ring). The critical overlap is at the CK rising edge, where the race path is only S₁–Inv₁–S₂ (one inverter delay); non‑overlapping phases, or deriving CK from CK̄ rather than vice versa, remove the hazard.\n- If the switches are single NMOS devices, the passed high level is degraded by V_TH; transmission gates or the restoring action of the inverters are needed. No static power is consumed – the attraction of this very compact dynamic divider (the TSPC divider is its single‑clock‑phase relative).\n\nIn short: the three‑inverter \"ring\" with alternately closed switches does not oscillate on its own; it toggles once per clock period and acts as a ÷2 frequency divider with 50 % duty cycle and quadrature outputs.",
        "format": "markdown",
        "sha256": "b959bb7ddd89b06d995cad578595e4e9dc28f87a975490cc9decef3827023e24"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the circuit as a dynamic-latch divide-by-two. The additional topology and timing details are secondary to the essential answer.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 17534,
        "total_tokens": 18967,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15588,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 17534,
        "total_tokens": 18967,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15588,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\nReading the loop from left to right we have\n\nS₁(CK) → Inv₁ → S₂(CK̄) → Inv₂ → Inv₃ → back to S₁.\n\n- S₁ + Inv₁ is a *dynamic latch*: when CK is high the latch is transparent; when CK goes low, S₁ opens and the sampled level is held on the gate capacitance of Inv₁.\n- S₂ + Inv₂ is a second dynamic latch, transparent when CK is low and holding when CK is high.\n- Two latches driven by complementary phases form a master–slave (edge‑triggered) flip‑flop; Inv₃ closes the loop with an extra inversion, i.e. D = Q̄.\n\nSo the arrangement is a dynamic master–slave *toggle* flip‑flop – a divide‑by‑2 circuit.\n\n**Why it does not oscillate even though three inverters are in a loop**\n\nThree inverters in a closed loop would be a ring oscillator, but here the loop is never closed: CK and CK̄ are complementary, so at any instant one of the two switches is open. The signal can advance past only one switch per half clock period, so one trip around the loop (one net inversion) is forced to take exactly one clock period instead of the inverters' own delay. Two trips (= one output period) therefore take 2T_CK.\n\n**Step‑by‑step operation**\n\nCall A the output of Inv₃ (input of S₁), B the input of Inv₁, C the output of Inv₁, D the input of Inv₂, E the output of Inv₂. Suppose D is initially holding 0.\n\n| half‑cycle | CK | S₁ | S₂ | A | B | C | D | E |\n|---|---|---|---|---|---|---|---|---|\n| 1 | 1 | on | off | 0 | 0 | 1 | 0 (held) | 1 |\n| 2 | 0 | off | on | 1 | 0 (held) | 1 | 1 | 0 |\n| 3 | 1 | on | off | 1 | 1 | 0 | 1 (held) | 0 |\n| 4 | 0 | off | on | 0 | 1 (held) | 0 | 0 | 1 |\n| 5 | 1 | on | off | 0 | 0 | 1 | 0 (held) | 1 (= row 1) |\n\nThe state repeats every four half‑cycles, i.e. every 2T_CK. Every node toggles once per clock period, so **f_out = f_CK/2**:\n\n- Node B (master) changes on the rising edges of CK; nodes D, E, A (slave) change on the falling edges. B and D are therefore in quadrature (90° apart at the output frequency), and E/A are a complementary (differential) pair.\n- Each output is high for one T_CK and low for one T_CK → 50 % duty cycle regardless of the duty cycle of CK.\n- The circuit is self‑starting: any imbalance at the floating nodes is amplified by the inverter gain (loop gain −A³ per clock period) until full swings are reached.\n\n**Practical limitations**\n\n1. *Clock overlap / race*: if CK and CK̄ overlap so that both switches are momentarily on, the three‑inverter ring is closed and can free‑run, corrupting the stored state. If CK̄ is produced from CK by an inverter, the overlap occurs at the rising edge of CK, and the race path is S₁ → Inv₁ → S₂; the circuit survives only if the overlap is shorter than the switch‑plus‑Inv₁ delay (hence the critical role of Inv₁). Non‑overlapping phases remove the problem.\n2. *Dynamic storage*: nodes B and D float for half a period, so leakage sets a minimum clock frequency; charge injection and clock feedthrough from the switches disturb these nodes; NMOS‑only switches pass only V_DD − V_TH (use transmission gates).\n3. *Maximum speed*: in each half period the data must settle through a switch and the following inverter(s): T_CK/2 ≳ t_sw + t_Inv1 and T_CK/2 ≳ t_sw + t_Inv2 + t_Inv3 (the slave half, with two inverters, is the bottleneck), i.e. f_CK,max ≈ 1/[2(t_sw + 2t_inv)].\n\nIn short: the figure is a ÷2 circuit built from two clocked dynamic latches plus an inverting feedback; the odd number of inversions provides the toggling, and the complementary switches prevent the loop from ever closing, so it divides rather than oscillates.",
        "format": "markdown",
        "sha256": "241eb5f08da1637d23b930c05f55e83d0814f3a497c38b3925da6fbd15792cb6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the arrangement as a dynamic master–slave divide-by-two circuit, with output frequency half the clock frequency. The additional operational details are not required for full credit and do not undermine that central conclusion.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 16726,
        "total_tokens": 18159,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15194,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1433,
        "output_tokens": 16726,
        "total_tokens": 18159,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15194,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the circuit is**\n\nWithout the red inverter the loop is a dynamic ÷2 stage: S1 + Inv1 is one latch, S2 + Inv2 is a second latch, and Inv3 supplies the extra inversion that makes the flip‑flop toggle. Because CK and CK̅ never turn both switches on at the same time, the loop is never closed – the data simply advance one latch per half clock period, and node A toggles once per clock cycle. The \"memory\" during the CK‑low phase is the charge stored on the gate of Inv1.\n\n**What the red inverter does**\n\nIt ties node A (output of Inv3) straight to node X (output of Inv1), i.e. it is a path around S1 and Inv1 that is *not* gated by the clock.\n\n- CK high (S1 on, S2 off): the red inverter is simply in parallel with Inv1 – same polarity, it helps pull X, but it also adds capacitance to A and X.\n- CK low (S1 off, S2 on): Inv1 holds X at the old value. After one switch delay + two inverter delays, Inv2/Inv3 flip node A, and now the red inverter tries to drive X to the *opposite* level. Two things follow:\n  1. Contention between Inv1 and the red inverter → static current, a degraded level at X (and at the input of Inv2, since S2 is on) → reduced noise margin.\n  2. If the red inverter is strong enough to win, X flips while S2 is still on, so the path red inverter → S2 → Inv2 → Inv3 → red inverter is a closed three‑inverter ring: the circuit free‑runs, the state stored in Inv1 is overwritten, and the output is no longer f_CK/2 (glitches/extra transitions).\n\n**Net effect on performance**\n\n- Speed: the critical path of the divider is S2 + Inv2 + Inv3, which the red inverter does not shorten – and it loads Inv3 more. The only gain appears at very high clock rates, where A happens to change only while S1 is on; then the loop delay no longer contains S1 and f_max rises by roughly one switch delay. But in that regime the circuit is really an injection‑locked ring oscillator, not a latch‑based divider.\n- Operating range: the plain divider works from the leakage‑limited minimum frequency up to f_max. With the red inverter, correct operation at lower clock rates depends on Inv1 overpowering the red inverter; otherwise the loop oscillates on its own. The range shrinks to roughly an octave around twice the ring’s natural frequency.\n- Power: static (contention) current during part of every cycle.\n- Robustness: operation becomes ratioed – it depends on the relative sizing of Inv1 and the red inverter (process, mismatch).\n- It does not solve the dynamic‑node leakage problem; a “keeper” that would make the first latch static has to go from X back to the input of Inv1, not from A to X.\n\nSo the red inverter trades the robust, wide‑range clocked‑latch behavior for contention, higher power and a narrow frequency window, with at best a marginal increase in maximum speed.",
        "format": "markdown",
        "sha256": "c1151f8d8468196e114d31482f7f9bd430e24a0623b63a36b15d0f087e46037d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly identifies the ungated path bypassing S1/Inv1, recognizes a speed benefit, and describes the low-frequency contention/ring behavior that raises the minimum usable frequency. However, it contradicts the feedforward speed mechanism by saying the critical path is not shortened, and its specific narrow locking-range claim is unsupported.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 42584,
        "total_tokens": 43816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41559,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 42584,
        "total_tokens": 43816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41559,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the red inverter is doing**\n\nLook at where it is connected: its input is tied to the divider output (the node to the left of the CK switch, i.e. the output of the last inverter) and its output is tied to the output of Inv₁. So it is a permanently‑on path in parallel with the clocked path “S₁ → Inv₁”. Together with the two right‑hand inverters it closes a three‑inverter loop (red → S₂ → Inv₂ → Inv₃) every time CK is low. The circuit therefore becomes a hybrid between a dynamic (switched‑ring) divider and a free‑running ring oscillator.\n\n**Reference: the circuit without it**\n\n- CK high: S₁ on, S₂ off → X = Ā, the node after S₂ holds its charge.\n- CK low: S₁ off, S₂ on → X propagates through Inv₂, Inv₃ and A toggles; Inv₁’s input floats and holds.\n\nThe data must travel once around the loop per clock period, so f_CK,max ≈ 1/(t_S1 + t_Inv1 + t_S2 + t_Inv2 + t_Inv3). The lower limit is set only by leakage on the floating nodes, so the range is wide.\n\n**Effect of the red inverter**\n\n1. Speed (the benefit): when A toggles during the CK‑low phase, the red inverter immediately starts driving X toward its *next* value (Ā_new) instead of waiting for CK to rise and for the RC of S₁. When S₁ then closes, Inv₁ and the red inverter pull X in the same direction. S₁’s delay and part of Inv₁’s delay drop out of the critical path, so the maximum clock frequency rises. If the red inverter is made strong, the loop red–Inv₂–Inv₃ oscillates by itself (f₀ ≈ 1/[2(t_R + t_S2 + t_2 + t_3)]) and the clocked path merely injection‑locks it – the divider then works up to about 2f₀ plus the lock range, beyond what the pure dynamic divider can do.\n\n2. Contention/power/noise margin: during the latter part of each CK‑low phase Inv₁ (holding the old value on its floating input) and the red inverter fight each other. This draws static current, degrades the level at X (and hence at Inv₂’s input), and forces a ratioed design: the red inverter must be weak relative to Inv₁, which makes the circuit sensitive to process/temperature. It also adds capacitance to A and X, eating into part of the speed gain.\n\n3. Operating range: what is gained at the high end is lost at the low end. With a long CK‑low phase the closed loop has time to flip Inv₂ or to oscillate, corrupting the state; the floating node still leaks as well. The divider therefore works only in a band around 2f₀ (an injection‑locking range) rather than from a leakage‑set minimum up to f_max, and PVT drift can push it out of lock. If the red inverter is too strong the circuit simply free‑runs and stops dividing.\n\n**Bottom line:** the red inverter turns the dynamic divider into a (partially) self‑oscillating, injection‑locked ring: higher maximum speed, but at the cost of contention power, degraded logic levels, ratioed sizing, and a much narrower, PVT‑sensitive frequency range.",
        "format": "markdown",
        "sha256": "b5f76a7a466cc960554473666e1d1f5ab53d2e394a748c3660470943c824a964"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the red inverter as an always-on feedforward path that bypasses part of the first latch path, improving high-speed operation. It also captures the essential low-frequency drawback: the unclocked branch can overpower or oscillate against the main path, raising the minimum usable clock frequency. The ring/injection-locking description is consistent with the golden solution.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 26513,
        "total_tokens": 27745,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25406,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 26513,
        "total_tokens": 27745,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25406,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**What the red inverter actually does**\n\nLook at where it is connected: its input is the node *before* the CK switch (the output of the last inverter, call it A) and its output is tied to the output of Inv₁ (call it B). So it is not a keeper around Inv₁ – it sits in parallel with the whole first latch (switch + Inv₁) and provides a permanently‑on, inverting path from A to B that bypasses the CK switch.\n\n**Behaviour in the two clock phases**\n\n- CK high (first switch on, second switch off): Inv₁ sees A and produces Ā; the red inverter also produces Ā. They agree, so the red inverter is redundant – it only adds capacitance to nodes A and B.\n\n- CK low (first switch off, second switch on): the input of Inv₁ is floating and holds the old value, so Inv₁ keeps B = Ā_old. But in this very phase the loop B → Inv₂ → Inv₃ → A is closed and A toggles to Ā_old. The red inverter now tries to drive B to A_old, i.e., opposite to what Inv₁ is holding. The two inverters fight for the entire half‑cycle, and this is exactly the half‑cycle in which the second latch samples B.\n\n**Consequences for performance**\n\n1. The circuit becomes ratioed. The red inverter must be much weaker than Inv₁. If it is comparable or stronger, B goes to an intermediate level or flips, and the red inverter + Inv₂ + Inv₃ form a three‑stage ring oscillator that free‑runs while CK is low – the circuit no longer divides by 2.\n\n2. Even with a weak red inverter: B (and therefore the dynamic node at the input of Inv₂) has a degraded logic level during the sampling phase → reduced noise margin, crowbar current in Inv₂, and a floating node stored at a degraded voltage.\n\n3. Static power: contention current flows through Inv₁ and the red inverter for half of every clock period.\n\n4. Speed: the extra gate/drain capacitance slows the output node A and node B. The only \"benefit\" is that B gets a small head start toward its next value before CK rises, but the slow half of the loop (switch + Inv₂ + Inv₃) is not helped at all, so there is no real gain in maximum frequency. Correct operation also becomes sensitive to the Inv₁/red‑inverter strength ratio over PVT.\n\n5. It does not make the latch static: the input node of Inv₁ still floats when CK is low, so the minimum operating frequency (leakage limit) is not improved – if anything the margin is slightly worse, because the red inverter is already pulling B toward the wrong value.\n\nBottom line: the red inverter degrades the divider (contention, static power, lower noise margin, more loading, no speed advantage) and, if sized too large, breaks it. If the intent was a static (leakage‑immune) latch, the weak feedback inverter must be placed from the output of Inv₁ back to its input node (after the switch), not across the switch – and even that costs some speed and power because the preceding stage must overpower it.",
        "format": "markdown",
        "sha256": "b3241aa8ec09902c38f3c8560e7b3135de6731d0ce1ca0d443569c35e426bfb0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the bypass connection and the unclocked three-inversion loop that can fight Inv₁. However, it denies the key high-speed benefit and does not identify the low-frequency mechanism that raises the minimum usable clock frequency, instead attributing the limit to leakage.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 29614,
        "total_tokens": 30846,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28600,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1232,
        "output_tokens": 29614,
        "total_tokens": 30846,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28600,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No, I don't agree.** The red inverter is not wired as a keeper at all.\n\n**What the circuit is.** Three inverters in a ring with two complementary switches is the classic dynamic ÷2: CK‑switch + Inv1 is the master, CK̄‑switch + Inv2 is the slave, and Inv3 supplies the extra inversion so the loop toggles (Q ← Q̄) every cycle. The state is stored dynamically on two floating nodes – the input of Inv1 (floats while CK is low) and the input of Inv2 (floats while CK is high). Leakage on those two nodes is what sets the minimum clock frequency.\n\n**Why it is not a keeper / cross‑coupled latch.** A keeper for Inv1 would have to be a (weak) inverter pointing *backwards*, from Inv1's output to Inv1's *input*, so that the two inverters form a two‑inversion (positive‑feedback, bistable) loop that holds the floating node. Look at the red inverter's wiring:\n\n- its **input** is tied to the node *before* the CK switch (the output of the third inverter), not to Inv1's input;\n- its **output** is tied to Inv1's output;\n- it points in the **same direction** as Inv1.\n\nSo red and Inv1 are not back‑to‑back; their outputs are simply shorted together and they are driven from opposite sides of the CK switch. There is no two‑inverter loop anywhere, hence no latch, no hold action, and neither floating node is touched. (Even if one misreads the left end as Inv1's input, two parallel same‑direction inverters are still not a keeper.)\n\n**What it actually does.** Calling the nodes A (output of Inv3), X (input of Inv1), B (output of Inv1), C (input of Inv2):\n\n- Red forces B = Ā at all times, i.e. it *bypasses the CK switch*; the first stage is no longer a sampling stage.\n- It thereby creates a loop A → Red → B → (CK̄ switch) → Inv2 → Inv3 → A containing **three** inversions and only **one** switch. Whenever the CK̄ switch is on, this is an odd‑inversion loop – a three‑stage ring oscillator – so the circuit free‑runs instead of transferring the state (the two complementary switches were precisely what prevented the ring from ever being closed; the red inverter undoes that).\n- During the same phase Inv1 (whose input X holds the previously sampled value) drives B to the opposite level, so Red and Inv1 fight at node B. Depending on which is stronger you get oscillation, a contended/mid‑rail node, or (if Red is very weak) a divider that merely wastes power.\n- Nodes X and C still float exactly as before, so the leakage‑limited minimum frequency is unchanged.\n\nIn short, the red inverter is a feed‑forward/bypass inverter in parallel with the CK‑switch‑plus‑Inv1 path; it turns the ÷2 into a clock‑gated ring oscillator (or into a contention problem) and does nothing about leakage. To remove the minimum‑frequency limit you would instead add a weak inverter from B back to X (and one from Inv2's output back to C), making the master and slave static latches.",
        "format": "markdown",
        "sha256": "2229daf5cedaf35a9946506b480cfcc25d1c1c9c90937dd1489bdf71173ae617"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly rejects the keeper interpretation and identifies the feedforward branch bypassing the CK switch. However, it says the minimum frequency is unchanged and characterizes the circuit as simply free-running; the key tradeoff is that the branch can help at high speed but overpower the intended latch behavior at low clock rates, raising the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 32883,
        "total_tokens": 34190,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 32883,
        "total_tokens": 34190,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No, I don't agree.**\n\n**1. It is not cross‑coupled with Inv1.**  \nLook at how it is wired. Call the nodes: X = output of Inv3 (left of the CK switch), Y = input of Inv1 (right of the CK switch – the floating storage node of the first latch), Z = output of Inv1, W = input of Inv2 (storage node of the second latch).\n\nA keeper for Inv1 would be a *weak inverter drawn anti‑parallel to Inv1*: input at Z, output at Y, so that it refreshes the charge on the node that actually floats (Y) when the CK switch is off.\n\nThe red inverter points in the *same* direction as Inv1 and goes from X to Z. It therefore sits **in parallel with the clocked path \"CK switch + Inv1\"** – it is a feed‑forward (bypass) inverter, not a latch. It drives a node that is already driven (Z) from a node that is already driven (X), and it never touches Y. With CK stuck low, Y still leaks through the off switch toward X and nothing replenishes it, so the minimum‑frequency problem is completely untouched.\n\n**2. What it actually does.**  \nIt forces Z = X̄ at all times, independent of CK.\n\n- CK = 1: the CK switch is closed, Y = X, Inv1 also gives Z = X̄ → the red inverter is redundant.  \n- CK = 0: the CK̄ switch is closed, so the red inverter, Inv2 and Inv3 now form a closed loop with **three inversions** (red → CK̄ switch → Inv2 → Inv3 → back to the red inverter), i.e. a ring oscillator. As soon as the second latch updates X, the red inverter tries to flip Z while Inv1 (holding the old value of Y) insists on the opposite → contention at Z. If the red inverter is strong, the divider breaks and free‑runs as a (clock‑gated) ring oscillator; if it is weak, the divider survives but Z's level is degraded during the hold phase and static current flows.\n\nSo the red inverter converts the pure \"sample‑and‑hold\" dynamic divider into a loop with its own natural oscillation – a self‑oscillating / injection‑locked type of divider. That can *raise the maximum* clock frequency (node Z begins to move before CK rises, so the loop anticipates the next state), but it brings a lock range with it: the clock must now be fast enough that the ring cannot complete a transition during the CK = 0 phase. In other words, it introduces a minimum frequency of a different origin – the opposite of what the answer claims – and does nothing against leakage.\n\n**3. The correct leakage fix** would be weak inverters placed anti‑parallel to Inv1 (Z → Y) and to Inv2 (output of Inv2 → W), i.e. making the two latches static (ratioed) latches, or using a C²MOS/TSPC‑style latch.",
        "format": "markdown",
        "sha256": "5f0b0585d6ae129cd4c9f97014ca95391f5d3e0186e02227fcb33628ad3982b8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly rejects the keeper interpretation and identifies the red inverter as an unclocked feedforward bypass from the node before the CK switch to Inv1’s output. It captures the high-speed pre-drive benefit and the low-frequency ring/contention that can corrupt division and raise the minimum usable clock rate. Its wording about the leakage limit and the branch “forcing” the output is somewhat strong, but does not undermine the central explanation.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 29552,
        "total_tokens": 30859,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28588,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 29552,
        "total_tokens": 30859,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28588,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**No, I don't agree – the answer misreads the topology.**\n\n**Why it is not a keeper**\n\nCall the nodes: A = output of the last inverter (left side of the CK switch), X = input of Inv1 (right side of the CK switch), B = output of Inv1, C = input of Inv2 (right side of the CK̄ switch).\n\n* A keeper/cross‑coupled latch around Inv1 would have to be an *anti‑parallel* inverter: input at B, output at X, so that it restores the charge that leaks off the floating node X while the CK switch is open (and a second one would be needed around Inv2–Inv3 for the other floating node C).\n* The red inverter is nothing of the sort. Its input is tied to A and its output to B – it points in the **same direction as Inv1**, sitting in parallel with the \"CK‑switch + Inv1\" branch. It is not connected to either floating node (X or C), so it cannot replenish leaked charge. The minimum‑clock‑frequency (leakage) problem is completely unaffected.\n\n**What the red inverter really does**\n\nIt is a **feed‑forward/bypass path around the CK switch**: it forces B = Ā at all times, independent of CK, i.e. it makes the first (master) stage permanently transparent. Consequences:\n\n* When CK is high (CK̄ switch open) nothing changes – Inv1 and the red inverter agree.\n* When CK is low (CK̄ switch closed) the loop red‑inverter → Inv2 → Inv3 → red‑inverter is a closed loop with three inversions: a **free‑running three‑stage ring oscillator**. At the same time Inv1, whose input X is frozen at the old value, tries to hold B at the old level, so the two inverters fight at node B (contention, degraded levels, static current). Depending on relative strengths the loop either oscillates during the whole CK‑low phase or sits at a ratioed, ill‑defined level.\n\nSo the red inverter destroys the master–slave isolation that makes the circuit a ÷2 dynamic divider; the circuit degenerates into a ring oscillator that is simply gated/frozen by CK̄, not a static divider. If one really wants a static (leakage‑immune) divider, weak (or clocked) inverters must be cross‑coupled from B back to X and from the output of Inv3 back to C – i.e. at the floating nodes – not placed in parallel with Inv1.",
        "format": "markdown",
        "sha256": "ce73972b79cff8a43ab27aaf37658023eec65e284d9b8c36d5091d03c16ea9fd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly rejects the keeper interpretation and identifies a feedforward bypass, along with the loop and contention it can create. But it wrongly says the minimum usable frequency is unaffected and that the circuit simply degenerates into a ring oscillator; the key tradeoff is that the branch can speed high-rate operation yet corrupt division at low rates, raising the minimum usable clock frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 23161,
        "total_tokens": 24468,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22366,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1307,
        "output_tokens": 23161,
        "total_tokens": 24468,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22366,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** with the input matched, the total transconductance is frozen at g_m1 + g_m2 = 1/R_S, so the transistor noise term is pinned at ≈ γ and cannot be reduced by burning more current. The only knob left (in the ideal, λ = 0 model) is R_F: make it as large as gain/bandwidth/linearity allow, and the NF approaches its floor of 1 + γ. To get below that floor you must let g_m1 + g_m2 exceed 1/R_S while keeping R_in = 50 Ω, which is possible only through the finite output resistance (raise G_m and R_F together).\n\n**Why (small‑signal, C1 ≈ short, λ = 0)**\n\nM1 and M2 share gate (X) and drain (Y), so they act as a single transconductor G_m = g_m1 + g_m2 whose signal and noise currents both flow through R_F:\n\n- Input resistance: I_in = G_m·V_X ⇒ R_in = 1/(g_m1 + g_m2), independent of R_F.\n- Gain (matched): V_out/V_in = (1 − G_m R_F)/2 = (R_S − R_F)/(2R_S) ≈ −R_F/(2R_S).\n- Noise: M1 and M2 contribute 4kTγ(g_m1+g_m2)(R_S+R_F)²/(1+G_mR_S)² at the output; R_F's noise 4kTR_F appears directly at the output.\n\nWith G_m R_S = 1:\n\nNF = 1 + γ[(R_F + R_S)/(R_F − R_S)]² + 4R_S R_F/(R_F − R_S)² ≈ 1 + γ + 4R_S/R_F\n\n**What this implies for the design**\n\n1. *Split of transconductance:* the match fixes only the sum (20 mS). How it is divided between M1 and M2 does not affect the NF (if γ_n ≈ γ_p); if one device is noisier, give more g_m to the quieter one. Note the benefit over a CS stage with a plain PMOS current‑source load: there M2's noise adds γ·g_m2/g_m1 with no signal; here M2's noise \"pays for itself,\" and the 20 mS is obtained with roughly half the current (current reuse).\n\n2. *Maximize R_F:* NF decreases monotonically with R_F. R_F carries no DC current (it only self‑biases the inverter), so there is no headroom penalty; the limits are the resulting gain |A_v| ≈ R_F/(2R_S) (linearity, output swing) and bandwidth (output time constant ≈ (R_F/2)·C_Y, Miller‑multiplied C_gd at the input, and R_in drifting toward R_F at high frequency). For γ = 1: R_F = 500 Ω → 4.8 dB, 1 kΩ → 3.9 dB, 2 kΩ → 3.4 dB, ∞ → 3 dB. That 1 + γ floor is the price of forcing G_m R_S = 1.\n\n3. *Getting below 1 + γ:* with real devices (r_O = r_O1‖r_O2),\n\n   R_in = (R_F + r_O)/(1 + G_m r_O)\n\n   so you can raise G_m above 1/R_S (wider devices/more current — the PMOS g_m comes free per unit current) and restore 50 Ω by increasing R_F = R_S(1 + G_m r_O) − r_O. Then (for R_F ≫ R_S)\n\n   NF ≈ 1 + γ/(G_m R_S) + (R_S/R_F)·[(2r_O + R_F)/(r_O + R_F)]²\n\n   which keeps falling as G_m and R_F grow (e.g., G_m r_O = 20, r_O = 500 Ω, R_F = 550 Ω gives ≈ 2.7 dB vs ≈ 4.6 dB for the g_m = 1/R_S design at the same R_F). The costs are power, the required intrinsic gain G_m r_O ≈ R_F/R_S, larger input capacitance, and higher gain/linearity pressure. So the practical recipe is: pick the largest G_m the power budget allows, then set R_F from the matching equation.\n\n(If even that is insufficient, the remedy is architectural rather than parametric: a noise‑cancelling second stage, exploiting that M1/M2 noise appears in phase at X and Y while the signal appears in antiphase.)",
        "format": "markdown",
        "sha256": "0af451ca548bb579f3d89d2688061acfce650644dac92e340a4a4e8ee4d80744"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly includes finite output resistance in the input-match relation and explains that gm can exceed 1/Rs while RF is adjusted to hold Rin at 50 Ω, allowing NF below 1 + γ. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 38014,
        "total_tokens": 40703,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36521,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 38014,
        "total_tokens": 40703,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36521,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Small‑signal model.** M1 and M2 see the same gate voltage and drive the same output node, so they act as one transistor with\n\n- $G_m = g_{m1}+g_{m2}$, $r_O = r_{O1}\\,\\|\\,r_{O2}$\n- channel noise $\\overline{i_n^2}=4kT\\gamma (g_{m1}+g_{m2}) = 4kT\\gamma G_m$\n\n(R_F carries no dc current, so the stage self‑biases at $V_{out}=V_{in}$ and R_F costs no headroom.)\n\n**Input resistance** (Miller‑reduced feedback resistor):\n\n$$R_{in}=\\frac{R_F+r_O}{1+G_m r_O}\\;\\;\\xrightarrow{\\;\\lambda=0\\;}\\;\\;\\frac{1}{g_{m1}+g_{m2}}$$\n\n**Noise figure** (R_S = 50 Ω). With $D=r_O(1+G_mR_S)+R_S+R_F$, the output noise contributions are\n\n- from R_S: $4kTR_S\\,r_O^2(G_mR_F-1)^2/D^2$\n- from R_F: $4kTR_F\\,r_O^2(1+G_mR_S)^2/D^2$\n- from M1,M2: $4kT\\gamma G_m\\,r_O^2(R_S+R_F)^2/D^2$\n\nso\n\n$$NF = 1+\\frac{R_F}{R_S}\\frac{(1+G_mR_S)^2}{(G_mR_F-1)^2}+\\gamma\\,G_mR_S\\frac{(1+R_F/R_S)^2}{(G_mR_F-1)^2}$$\n\n($r_O$ is noiseless and drops out.)\n\n**Optimization with R_in fixed at 50 Ω**\n\n1. If channel‑length modulation is neglected, matching *pins* the transconductance: $g_{m1}+g_{m2}=1/R_S=20$ mS. Then\n\n$$NF\\approx 1+\\gamma+\\frac{4R_S}{R_F}$$\n\nThe transistor term γ cannot be touched (the device noise $4kT\\gamma G_m$ is fixed by the match), and how G_m is split between NMOS and PMOS is irrelevant. The only knob is R_F: make it as large as possible (it carries no dc current, so only its parasitic capacitance/bandwidth limit it); NF → 1+γ (≈3 dB for γ≈1). In this limit the inverter is no better in NF than a single CS stage with current‑source load – its benefit is current reuse (20 mS for half the drain current).\n\n2. In a real design r_O is finite, and then $R_{in}\\approx R_F/(1+G_m r_O)$ – the 50 Ω is produced by the *loop gain*, not by $1/G_m$. This decouples G_m from the match and is the real optimization:\n - increase $g_{m1}+g_{m2}$ well above 20 mS (wider devices/more current, sized so both devices contribute, e.g. W_p/W_n ≈ μ_n/μ_p),\n - and raise R_F in step to keep the input at 50 Ω:\n $$R_F = R_S(1+G_m r_O)-r_O$$\n \n With $G_mR_S\\gg1$ and $R_F\\gg R_S$ the NF becomes\n\n$$NF\\approx 1+\\frac{R_S}{R_F}+\\frac{\\gamma}{G_mR_S}\\;\\approx\\;1+\\frac{1}{G_m r_O}+\\frac{\\gamma}{G_mR_S}$$\n\n which decreases as G_m grows. Example: $g_m r_O\\approx 20$, $G_m=100$ mS ⇒ $r_O\\approx200\\ \\Omega$, $R_F\\approx 850\\ \\Omega$, NF ≈ 1.3 (≈1.2 dB) instead of ≈3.4 dB, with $|A_v|\\approx 8$.\n\nThe limits are power dissipation, the intrinsic gain $g_m r_O$ of the technology (which caps R_F at ≈ R_S(1+g_m r_O) and the gain at ≈ g_m r_O/2), and the input capacitance $C_{GS1}+C_{GS2}$ + Miller $C_{GD}$ that spoils the 50 Ω match at high frequency.",
        "format": "markdown",
        "sha256": "c5ae237cc10caf687ec1ee923d1af2d64e9d47c6ff7dbb328851dcf47cb9db49"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly includes finite output resistance in the input-match relation and explains that gm can exceed 1/Rs while RF is adjusted to preserve Rin = 50 Ω, allowing NF below 1 + γ. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 24430,
        "total_tokens": 27119,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22957,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 24430,
        "total_tokens": 27119,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22957,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up the problem (Gm ≡ gm1 + gm2, rO ≡ rO1‖rO2)**\n\nM1 and M2 are both driven by the input and both dump their current into the same node, so the inverter behaves like a single device with transconductance Gm = gm1 + gm2 and noise current 4kTγGm. The input is ac‑coupled (C1) and the gates draw no dc current, so RF carries **no dc current**; it only self‑biases the inverter (VG = VD) – a large RF costs no headroom.\n\n*Neglecting channel-length modulation:*\n\n- Rin = 1/(gm1 + gm2), independent of RF → matching forces **gm1 + gm2 = 1/RS = 20 mS**\n- Av = Vout/Vin = (1 − RF/RS)/2 ≈ −RF/(2RS)\n- Output noise: RS → 4kTRS·Av² ; RF → 4kTRF (appears unattenuated, VX = 0) ; M1,M2 → 4kTγGm[(RS+RF)/2]²\n\nNF = 1 + 4RSRF/(RF − RS)² + γ[(RF + RS)/(RF − RS)]² ≈ **1 + γ + 4RS/RF**\n\n(with unequal excess‑noise factors, γ → (γn·gm1 + γp·gm2)/(gm1 + gm2)).\n\n**What this tells you**\n\n1. The PMOS is \"free\" noise-wise: used as a plain current source it would add γ·gm2/gm1 to the NF; with its gate tied to the input its noise buys an equal amount of useful gm. Equivalently, the required 20 mS is reached with about half the current of an NMOS‑only stage.\n2. Because Rin pins Gm·RS = 1, the transistor term is frozen at γ: burning more current does not help, and (for γn = γp) it does not matter how the 20 mS is split between M1 and M2 (if γp < γn in your process, let the PMOS carry the larger share; keep overdrives low/L not minimum to keep γ small).\n3. The **only free knob is RF → make it as large as possible**. It is limited only by the gain it implies (|Av| ≈ RF/2RS → linearity/headroom at the output) and by bandwidth (Rout ≈ (RF + RS)/2 with CL, Miller-multiplied Cgd at the input). Even with RF → ∞ the NF floor is 1 + γ (≈3 dB for γ ≈ 1).\n\n**Getting below 1 + γ while keeping 50 Ω – use the finite output resistance**\n\nWith rO (or any load) included,\n\nRin = (RF + rO)/(1 + Gm·rO).\n\nNow Gm is no longer locked to 1/RS: you may raise gm1 + gm2 (wider devices, more current) and restore Rin = 50 Ω by raising RF with it:\n\nRF = RS + rO(GmRS − 1)  ⇔  GmRS = 1 + (RF − RS)/rO.\n\n(Note that with finite rO, Gm = 1/RS would force RF = RS, i.e., zero gain – a real inverter LNA *must* run at GmRS > 1.) Repeating the noise analysis under this matching condition gives\n\nNF = 1 + [RSRF(1 + GmRS)² + γ·GmRS·(RF + RS)²] / [(RF − RS)²(1 + RF/rO)²]\n  ≈ 1 + γ/(GmRS) + (1 + 1/GmRS)²·RS/RF  (RF ≫ RS)\n\nBoth terms fall as RF and Gm are increased together. Example with rO = 500 Ω, RF = 800 Ω: GmRS = 2.5 (gm1 + gm2 = 50 mS, ≈2.5 mA at gm/ID ≈ 10 V⁻¹), Av ≈ −7.5 (17.5 dB), NF ≈ 1 + 0.4γ + 0.12 ≈ 1.5 (≈1.8 dB for γ = 1) instead of >3 dB. Pushing to RF = 2 kΩ, Gm ≈ 100 mS gives ≈1 dB, at the cost of ~5 mA, 26 dB of gain (linearity), and more input capacitance (match bandwidth).\n\n**Summary:** With Rin fixed at 50 Ω you cannot lower the NF the \"usual\" way (just raising gm). Keep gm1 + gm2 and RF tied by (RF + rO)/(1 + (gm1+gm2)rO) = 50 Ω and push both up: RF as large as the gain/bandwidth budget allows and gm1 + gm2 as large as the power budget allows (letting the PMOS supply a good share of it). If rO is truly negligible, the only move left is maximizing RF, and NF ≥ 1 + γ.",
        "format": "markdown",
        "sha256": "d5726228d20828c7fe282ad2bc85b7c3f3df6629bed42f416ab9a29b4f079f0a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly uses the finite-output-resistance input-match relation and explains that gm can exceed 1/Rs while RF is increased to preserve Rin, allowing NF below 1 + γ. This matches the golden solution’s full-credit rule.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 35715,
        "total_tokens": 38404,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34076,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2689,
        "output_tokens": 35715,
        "total_tokens": 38404,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34076,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Setting up (small‑signal, λ = γ = 0, ideal I_SS, M₂ ≡ M₃ with transconductance g_m3)**\n\nApply a test voltage V_P at the input node P (to the right of C_in, where R_in is defined) and find the current drawn through R_F.\n\n1. **First stage (M₁, R_D1):** the gate of M₂ draws no current, so \n\n V_X = −g_m1 R_D1 V_P\n\n2. **Second stage (PMOS pair M₂–M₃):** with the gate of M₃ at ac ground, the tail node moves by half the input, V_S = V_X /2. The small‑signal current M₃ pushes into the output node is therefore \n\n i_3 = g_m3 V_S = (g_m3 /2) V_X = −(g_m1 R_D1 g_m3 /2) V_P ≡ −G_m V_P ,  G_m = g_m1 R_D1 g_m3 /2\n\n3. **KCL at the output node** (R_D2 and R_F both load it):\n\n −G_m V_P = V_out /R_D2 + (V_out − V_P)/R_F\n\n ⇒ V_out = R_D2 (1 − G_m R_F)/(R_F + R_D2) · V_P\n\n4. **Input current** (through R_F):\n\n I_in = (V_P − V_out)/R_F = (1 + G_m R_D2)/(R_F + R_D2) · V_P\n\n**Result**\n\n$$\nR_{in}= \\frac{R_F+R_{D2}}{1+\\dfrac{g_{m1}R_{D1}\\,g_{m3}R_{D2}}{2}}\n=\\frac{R_F+R_{D2}}{1+A_0},\\qquad \nA_0=\\tfrac12 g_{m1}R_{D1}g_{m3}R_{D2}\n$$\n\ni.e. the feedback resistor (plus the open‑loop output resistance R_D2) divided by one plus the open‑loop gain of the two stages (CS gain g_m1R_D1 times the single‑ended differential‑pair gain g_m3R_D2/2). For A₀ ≫ 1 and R_F ≫ R_D2 this is ≈ R_F /A₀.\n\nIf the photodiode capacitance is included, the total impedance seen by I_in is simply this resistance in parallel with C_in:\n\n$$\nZ_{in}(s)=\\frac{R_F+R_{D2}}{1+A_0}\\;\\Big\\|\\;\\frac{1}{C_{in}s}\n=\\frac{R_F+R_{D2}}{(1+A_0)+(R_F+R_{D2})C_{in}s}.\n$$",
        "format": "markdown",
        "sha256": "57c76428d71a05ad4f8cb79d758184125e79b3fa603976d170c7319fe19de545"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Gives the exact input resistance, including the output-side resistance, and the correct unloaded gain definition. The additional capacitance discussion does not undermine the result.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 9390,
        "total_tokens": 9617,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8491,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 9390,
        "total_tokens": 9617,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8491,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the structure**\n\nThe circuit is a shunt‑shunt feedback TIA: $R_F$ returns the output to the input node $P$, and the forward amplifier consists of two stages:\n\n- $M_1$ (common source): inverting, $v_X/v_P=-g_{m1}R_{D1}$ (the gate of $M_2$ does not load $R_{D1}$).\n- $M_2$–$M_3$ differential pair driven at the gate of $M_2$ with the output taken at the *opposite* drain: non‑inverting. $M_2$ acts as a source follower driving $M_3$ as a common‑gate device, so the current delivered to $R_{D2}$ is \n $$i_{3}= \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}\\,v_X=\\frac{g_{m3}}{2}v_X \\quad (g_{m2}=g_{m3}),$$\n i.e. the stage gain is $+g_{m3}R_{D2}/2$.\n\nThe overall forward gain is therefore inverting (as required for negative feedback through $R_F$):\n\n$$A_0=\\frac{v_{out}}{v_P}\\Big|_{\\text{open loop}}=-\\,g_{m1}R_{D1}\\,\\frac{g_{m3}R_{D2}}{2}.$$\n\n**Input resistance (neglecting channel‑length modulation)**\n\nApply a test voltage $v_P$ at $P$ (looking into the TIA, i.e. excluding $C_{in}$) and find the current $i_P$ flowing in; since the gate of $M_1$ draws no current, $i_P$ flows entirely through $R_F$.\n\n1. $v_X=-g_{m1}R_{D1}v_P$\n2. KCL at the output node (current from $M_3$ splits between $R_{D2}$ and $R_F$):\n$$\\frac{v_{out}}{R_{D2}}+\\frac{v_{out}-v_P}{R_F}=\\frac{g_{m3}}{2}v_X=-\\frac{g_{m1}g_{m3}R_{D1}}{2}\\,v_P$$\n$$\\Rightarrow\\; v_{out}=v_P\\,\\frac{R_{D2}\\left(1-\\tfrac12 g_{m1}g_{m3}R_{D1}R_F\\right)}{R_F+R_{D2}}$$\n3. $i_P=\\dfrac{v_P-v_{out}}{R_F}=v_P\\,\\dfrac{1+\\tfrac12 g_{m1}g_{m3}R_{D1}R_{D2}}{R_F+R_{D2}}$\n\nHence\n\n$$\\boxed{R_{in}=\\frac{v_P}{i_P}=\\frac{R_F+R_{D2}}{1+\\dfrac{1}{2}\\,g_{m1}R_{D1}\\,g_{m3}R_{D2}}=\\frac{R_F+R_{D2}}{1+|A_0|}}$$\n\nThis has the same form as the single‑transistor feedback TIA, $(R_F+R_D)/(1+g_mR_D)$, with the loop gain now being the product of the two stage gains. (Channel‑length modulation can be included by replacing $R_{D1}\\to R_{D1}\\|r_{O1}$ and $R_{D2}\\to R_{D2}\\|R_{out,M3}$, with $R_{out,M3}\\approx 2r_{O3}$.)\n\nFor a large loop gain and $R_F\\gg R_{D2}$:\n\n$$R_{in}\\approx\\frac{R_F}{|A_0|}=\\frac{2R_F}{g_{m1}g_{m3}R_{D1}R_{D2}}.$$\n\nThe total impedance seen by the photodiode current source is this resistance in parallel with $C_{in}$: $Z_{in}(s)=R_{in}/(1+R_{in}C_{in}s)$, giving an input pole at $\\omega_{in}=1/(R_{in}C_{in})$ — much higher than $1/(R_FC_{in})$ thanks to the loop gain.",
        "format": "markdown",
        "sha256": "bde142f53245cdd03229f46f5d1a4be101eedb85b8007ed13617f213b18282d0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Derives the exact input resistance, (R_F+R_D2)/(1+|A_0|), with |A_0|=½g_m1g_m3R_D1R_D2, matching the golden result. The additional comments do not undermine the essential answer.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 12453,
        "total_tokens": 12680,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11064,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 12453,
        "total_tokens": 12680,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11064,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the topology**\n\n- $M_1$ with $R_{D1}$ is a common‑source stage (inverting): $V_X=-g_{m1}R_{D1}V_P$.\n- $M_2$–$M_3$ form a PMOS differential pair whose \"other\" input ($V_b$) is an ac ground. $M_2$ acts as a source follower and $M_3$ as a common‑gate device, so the signal reaching the drain of $M_3$ is **non‑inverting**: with matched devices ($g_{m2}=g_{m3}$) the small‑signal current delivered by $M_3$ into the output node is \n\n$$i_{D3}=\\frac{g_{m2}}{2}V_X .$$\n\n(For unmatched devices replace $g_{m2}/2$ by $g_{m2}g_{m3}/(g_{m2}+g_{m3})$.)\n\n- $R_F$ returns the output voltage as a current to node $P$: shunt–shunt (current‑in, voltage‑out) feedback, i.e. a transimpedance amplifier. Inverting stage × non‑inverting stage ⇒ the loop is negative.\n\n**Direct small‑signal analysis** (neglect channel‑length modulation, ideal $I_{SS}$; the gate of $M_1$ draws no current, so all of $I_{in}$ flows through $R_F$)\n\nDefine the gain of the core amplifier (without $R_F$):\n\n$$A_0 \\;=\\; g_{m1}R_{D1}\\,\\frac{g_{m2}R_{D2}}{2}$$\n\nKCL at the output node:\n\n$$\\frac{g_{m2}}{2}V_X+\\frac{V_P-V_{out}}{R_F}=\\frac{V_{out}}{R_{D2}},\\qquad V_X=-g_{m1}R_{D1}V_P$$\n\n$$\\Rightarrow\\quad V_{out}=\\frac{R_{D2}-A_0R_F}{R_F+R_{D2}}\\,V_P$$\n\nInput current:\n\n$$I_{in}=\\frac{V_P-V_{out}}{R_F}\n=\\frac{V_P}{R_F}\\cdot\\frac{R_F+R_{D2}-R_{D2}+A_0R_F}{R_F+R_{D2}}\n=\\frac{1+A_0}{R_F+R_{D2}}\\,V_P$$\n\n**Input impedance**\n\n$$\\boxed{R_{in}=\\frac{V_P}{I_{in}}=\\frac{R_F+R_{D2}}{1+A_0}\n=\\frac{R_F+R_{D2}}{1+\\dfrac{1}{2}\\,g_{m1}g_{m2}R_{D1}R_{D2}}}$$\n\n(Same result is obtained from Miller's theorem, $R_{in}=R_F/(1-V_{out}/V_P)$.)\n\nChecks/remarks:\n- With no gain ($A_0=0$) this reduces to $R_F+R_{D2}$, as expected.\n- For large loop gain and $R_F\\gg R_{D2}$, $R_{in}\\approx R_F/A_0=\\dfrac{2R_F}{g_{m1}g_{m2}R_{D1}R_{D2}}$ – the feedback lowers the input resistance by the gain of the core amplifier.\n- If $r_O$ is included, $R_{D1}\\to R_{D1}\\|r_{O1}$ (and similarly for the output node).\n- Including the photodiode/pad capacitance, the total input impedance is simply $Z_{in}(s)=R_{in}\\,\\|\\,\\dfrac{1}{C_{in}s}$, giving an input pole at $\\omega_{in}=1/(R_{in}C_{in})$.",
        "format": "markdown",
        "sha256": "d421a64b40127034ba0f2c99aa75dcb5b3e2b6e9a4358a7e78d0354812929d95"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Gives the exact input resistance, including the output-side resistance: \\(R_{in}=(R_F+R_{D2})/(1+A_0)\\), with the correct unloaded gain \\(A_0=\\tfrac12 g_{m1}g_{m2}R_{D1}R_{D2}\\). The derivation is consistent with the stated small-signal model.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 13938,
        "total_tokens": 14165,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12675,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 227,
        "output_tokens": 13938,
        "total_tokens": 14165,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12675,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Key observation:** the LDO noise does not just \"add\" to the output – it *frequency‑modulates* the oscillator, because the varactors are referenced to the supply.\n\n**1. Why the supply noise modulates the frequency**\n\nThe inductors carry no dc drop, so the common‑mode (average) voltage of nodes X and Y is equal to $V_{out}$. Each varactor $M_{v1,2}$ sits between X (or Y) and $V_{cont}$, so its capacitance is set by\n\n$$V_{var}\\approx V_{out}-V_{cont}.$$\n\nA noise voltage $V_n(t)$ riding on $V_{out}$ therefore changes $C_{var}$ exactly as noise on $V_{cont}$ would (only the sign is reversed). The tank frequency $\\omega_{out}=1/\\sqrt{L_1C_{tot}}$ thus becomes\n\n$$\\omega_{out}(t)=\\omega_0+K_{VDD}\\,V_n(t),\\qquad K_{VDD}=\\frac{\\partial\\omega_{out}}{\\partial V_{out}}\\approx -K_{VCO}.$$\n\n(More generally $K_{VDD}$ is the VCO's \"supply pushing\"; it also lumps in the $V_{out}$‑dependence of the junction capacitances of $M_1,M_2$, the switch parasitics in $B_1,B_2$, swing‑dependent effects, etc. It can be obtained from a simple simulation sweep of $V_{out}$ vs. $f_{out}$, but to first order it equals $K_{VCO}$.)\n\n**2. FM → phase noise**\n\nThe excess phase is the integral of the frequency deviation:\n\n$$\\phi_n(t)=K_{VDD}\\int V_n(t)\\,dt\\;\\;\\Longrightarrow\\;\\;\\Phi_n(j\\omega)=\\frac{K_{VDD}}{j\\omega}V_n(j\\omega).$$\n\nHence the phase‑noise spectrum at an offset $f$ from the carrier is\n\n$$\\boxed{S_{\\phi_n}(f)=\\frac{K_{VDD}^2\\,S_{th}}{(2\\pi f)^2}\\approx\\frac{K_{VCO}^2\\,S_{th}}{4\\pi^2 f^2}}$$\n\nwith $K$ in rad/s/V (if $K$ is in Hz/V, simply $S_{\\phi_n}=K^2S_{th}/f^2$). In dBc/Hz: $\\mathcal{L}(\\Delta f)=10\\log S_{\\phi_n}(\\Delta f)$ (3 dB lower if the strict single‑sideband definition $\\mathcal{L}=S_{\\phi}/2$ is used).\n\n**3. What this means**\n\n- White LDO noise produces a $-20$ dB/dec skirt, indistinguishable in shape from the oscillator's own thermal ($1/f^2$) phase noise; it is uncorrelated with it and simply adds to it. LDO flicker noise would add a $1/f^3$ term the same way.\n- Example: $K_{VCO}=2\\pi(100\\text{ MHz/V})$, $\\sqrt{S_{th}}=10\\ \\text{nV}/\\sqrt{\\text{Hz}}$ ⇒ at $\\Delta f=1$ MHz,\n $S_{\\phi_n}=(10^8\\times10^{-8})^2/(10^6)^2=10^{-12}$ → $-120$ dBc/Hz, i.e., comparable to the intrinsic phase noise of a good GHz LC VCO. A supposedly \"quiet\" 10 nV/√Hz regulator can therefore dominate the VCO phase noise.\n- Remedies follow directly from the formula: lower $S_{th}$ (low‑noise LDO, large bypass capacitor at $V_{out}$, which rolls off the noise as $S_{th}/[1+(2\\pi f R_{out}C_L)^2]$), and lower $K_{VCO}$ — which is precisely why the VCO in the figure uses the switched capacitor banks $B_1$, $B_2$ for coarse tuning and keeps the varactors (and hence $K_{VCO}$) small.",
        "format": "markdown",
        "sha256": "b6968a9b4941a5a95253a24cd580fa4c553fc8820ee9d09614d79852745310d6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing through the varactors, converts the LDO noise using the frequency sensitivity and FM-to-phase integration with a 1/offset² dependence, and notes the relation to KVCO and the benefit of reducing it. The spectral and single-sideband convention details are acceptable under the golden solution.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 11786,
        "total_tokens": 15520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10364,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 11786,
        "total_tokens": 15520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10364,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Key observation – the LDO noise enters through the varactors**\n\nThe inductors carry only dc, so the common‑mode level at X and Y is equal to the LDO output, V_out. The varactors M_v1 and M_v2 are therefore biased by\n\n  V_var = V_X,CM − V_cont = V_out − V_cont .\n\nAny noise v_n(t) on V_out changes the varactor voltage exactly as (minus) the same noise on V_cont would. Thus the VCO’s supply sensitivity is essentially equal to its gain: |K_VDD| ≈ K_VCO, and the LDO noise is indistinguishable from control‑line noise.\n\n**Frequency modulation → phase modulation**\n\nThe instantaneous frequency becomes\n\n  ω_out(t) = ω_0 + K_VCO v_n(t)   (K_VCO in rad/s/V),\n\nand the output is\n\n  V_X(t) = V_0 cos[ω_0 t + φ_n(t)],  φ_n(t) = K_VCO ∫ v_n(t) dt .\n\nIn the frequency domain the integration is a 1/s:\n\n  Φ_n(s) = K_VCO · V_n(s)/s .\n\n**Phase‑noise spectrum**\n\nWith the LDO output noise having a (white) spectral density S_th (V²/Hz),\n\n  S_φ(f) = |K_VCO/(j2πf)|² · S_th = K_VCO² S_th / (4π² f²)\n\n(or S_φ(f) = K_VCO² S_th / f² if K_VCO is expressed in Hz/V). In dBc/Hz at offset Δf,\n\n  L(Δf) = 10 log[K_VCO² S_th /(4π² Δf²)]\n\n(subtract 3 dB if the IEEE single‑sideband definition L = S_φ/2 is used).\n\n**Remarks**\n\n- The result has the same −20 dB/dec slope as the VCO’s own thermal (Leeson) phase noise and simply adds to it in power; LDO flicker noise would instead add a 1/f³ (−30 dB/dec) skirt.\n- Example: K_VCO = 2π(100 MHz/V) and an LDO noise of 10 nV/√Hz give S_φ ≈ (10⁸)²(10⁻¹⁶)/(10⁶)² = 10⁻¹² rad²/Hz → ≈ −120 dBc/Hz at 1‑MHz offset, i.e., comparable to a good VCO’s intrinsic noise. Hence the LDO must be very quiet (a few nV/√Hz), and one minimizes K_VCO by doing coarse tuning with the switched banks B₁, B₂.\n- S_th should be the noise actually appearing at V_out (reference + error‑amplifier + pass‑transistor noise, as shaped by the LDO loop and the output capacitor); beyond the LDO’s output pole it rolls off, and so does its contribution to the phase noise.",
        "format": "markdown",
        "sha256": "c2acdb2b52089cf777766be73c724a1158cfa9f96d1cc8d3aaa2ec1cfaa34657"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing through the varactors, uses the VCO sensitivity to convert LDO voltage noise to frequency noise, and applies FM-to-phase conversion with the required 1/Δf² dependence. The KVCO design implication is also captured; factor-of-two and 2π conventions are secondary.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 12068,
        "total_tokens": 15802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11078,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 12068,
        "total_tokens": 15802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11078,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Key observation – the LDO noise is really \"control‑voltage noise.\"**  \nThe inductors carry no dc drop, so the common‑mode level of nodes X and Y is exactly V_out. Each varactor (M_v1, M_v2) therefore has a gate‑to‑source (control) voltage of\n\n  V_var = V_out − V_cont .\n\nA noise voltage v_n(t) on V_out thus changes the varactor capacitance exactly as a noise voltage −v_n(t) on V_cont would. In other words, the VCO's supply sensitivity is essentially equal to its gain:\n\n  |K_VDD| = |∂ω_out/∂V_out| ≈ K_VCO\n\n(the switched‑capacitor banks and the junction/overlap capacitances of M_1, M_2 add only a small contribution).\n\n**Computation**\n\n1. The LDO noise frequency‑modulates the oscillator:  \n  ω_out(t) = ω_0 + K_VCO · v_n(t)\n\n2. Phase is the integral of frequency:  \n  φ_n(t) = K_VCO ∫ v_n(t) dt  ⇒ Φ_n(s) = K_VCO · V_n(s)/s\n\n3. Squaring the magnitude with s = j2πf:\n\n  **S_φn(f) = K_VCO² · S_th / (4π² f²)**  (K_VCO in rad/s/V)\n\n  or equivalently S_φn(f) = (K_VCO/f)² S_th with K_VCO in Hz/V. Taking 10 log of this gives the phase noise in dBc/Hz (to within the usual factor‑of‑2 convention between S_φ and L(Δf)), and it simply adds (in power) to the VCO's own phase noise.\n\n**What this tells us**\n\n- White (thermal) LDO noise produces a 1/f² phase‑noise skirt, indistinguishable in shape from the VCO's intrinsic thermal phase noise; the LDO's flicker noise similarly produces 1/f³ phase noise.\n- The effect is strong: e.g., with K_VCO = 2π(50 MHz/V) and S_th = (5 nV/√Hz)², at 1‑MHz offset S_φn ≈ (5×10⁷)²(2.5×10⁻¹⁷)/(10⁶)² ≈ 6×10⁻¹⁴ → ≈ −132 dBc/Hz, comparable to a good VCO's own phase noise.\n- Hence the LDO must have very low output noise (and/or the VCO a small K_VCO, i.e., most of the tuning done by the capacitor banks). Inside a PLL this noise is shaped exactly like the VCO's own phase noise (high‑pass, suppressed only within the loop bandwidth).",
        "format": "markdown",
        "sha256": "3d4a4a98b2666d7ddddcd88bef697aefdabdfd1fafb5d43ed8e983a21a5b9487"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing, converts LDO voltage noise through the VCO sensitivity into phase noise with a 1/Δf² dependence, and notes that direct varactor coupling makes the sensitivity closely related to KVCO. The factor-of-two convention and peripheral details do not affect the essential answer.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 10741,
        "total_tokens": 14475,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9815,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3734,
        "output_tokens": 10741,
        "total_tokens": 14475,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9815,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Two opposing things happen.**\n\n**1. The 2ω₀ noise of the tail source is filtered → phase noise improves.**  \nM₁ and M₂ act as a switching (commutating) mixer for whatever current flows in node P: the tail current is multiplied by a square wave S(t) with fundamental ω₀. Noise of I_SS near dc is translated to ω₀ ± Δω in phase with the carrier (AM, becomes PM only through varactor AM/PM conversion), but noise of I_SS at 2ω₀ ± Δω is translated to ω₀ ± Δω with unequal sidebands, i.e. it contains a PM component and appears directly as phase noise. C_T shunts this high‑frequency noise of I_SS to ground before it reaches the sources of M₁/M₂: if 1/(2ω₀C_T) ≪ 1/g_m (the impedance looking into the pair), most of the 2ω₀ noise current flows into C_T rather than being commutated to the tank. This removes a significant contributor to the 1/f² phase noise. (C_T does nothing for the low‑frequency/flicker noise of I_SS.)\n\n**2. Node P is no longer a high impedance → the tank is loaded → phase noise degrades.**  \nWith an ideal current source, when M₁ (or M₂) enters the triode region at the peaks of the swing it simply carries I_SS; node P follows node X and the on‑resistance R_on does not load the tank. With a large C_T, node P is an ac ground at ω₀ and 2ω₀, so the triode device connects the tank to ground through R_on + 1/(jωC_T) ≈ R_on for a fraction of every half‑cycle (the common‑mode current at 2ω₀ now flows into C_T). The effective parallel resistance of the tank drops, Q falls, and the phase noise due to the tank/transistor noise rises.\n\n**Net result:** C_T lowers the phase noise contributed by the tail current source but raises the phase noise from Q degradation when the transistors enter triode – a trade‑off (the parasitic capacitance of the current source already does this to some extent). The usual fix is the tail \"noise filter\": keep the large capacitor across I_SS but insert an inductor between node P and that capacitor so that it resonates with the parasitic capacitance at P at 2ω₀; node P then sees a high impedance at 2ω₀ (no tank loading) while the noise of I_SS is still shunted.",
        "format": "markdown",
        "sha256": "6dc36774fbc01c35b66c0afb2a55620fff8d5fbe6bc7f694861a3eec1ff4ac87"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It recognizes a tradeoff and identifies triode-related loading as a possible degradation, but misses the key class-C-like switching mechanism—peak tank currents exceeding ISS—that can lower phase noise. It instead attributes the improvement to filtering tail-source noise.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 17925,
        "total_tokens": 21781,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17103,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 17925,
        "total_tokens": 21781,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17103,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** it does not get better – in general it gets *worse*. The capacitor fixes one problem but creates a bigger one.\n\n**What C_T helps with**\n\nThe noise of I_SS near 2ω₀ (and other even harmonics) is normally commutated by the switching pair M₁–M₂ down to ω₀ ± Δω and injected into the tank, where it appears as phase noise. A large C_T presents a low impedance at 2ω₀ (|1/(2ω₀C_T)| ≪ 1/g_m), so this noise current is shunted to ground instead of flowing through M₁/M₂. That part of the tail‑source contribution drops. (The low‑frequency/1/f noise of I_SS is unaffected – C_T is an open circuit there – so the AM and AM‑to‑PM conversion through varactors remain.)\n\n**What C_T hurts**\n\nC_T turns node P into an ac ground. In a cross‑coupled oscillator with a large swing each transistor spends part of every cycle in the triode region: e.g. when V_Y is high and V_X is low, M₁ has a high gate voltage and a low drain voltage, so it is a resistor R_on1 between X and P.\n\n- Without C_T, P simply follows V_X (V_P ≈ V_X − I_SS·R_on1); only I_SS flows through R_on1 and the tank is not loaded.\n- With C_T, P is fixed, so R_on1 (in series with the large C_T) appears directly across the tank for that part of the cycle; the same happens with M₂ on the other half‑cycle. Tank energy is dissipated in R_on, the loaded Q drops, the oscillation amplitude drops, and since phase noise ∝ 1/(Q²·V²) it rises. In addition, the \"on\" device now behaves like a common‑source stage with a grounded source, so its own channel noise flows straight into the tank instead of being absorbed by the current source.\n\nSo the 2ω₀ tail noise is removed, but the periodic Q degradation (and extra M₁/M₂ noise) typically outweighs it – the phase noise rises.\n\n**Remedy:** the \"noise filter\" (Hegazi/Abidi): keep the large capacitor across the current source, but insert an inductor L_T between node P and it, sized to resonate with the total capacitance at P at 2ω₀. Node P then presents a high impedance at 2ω₀ (no loading through the triode device) while the capacitor still shunts the current‑source noise. (Alternatively, bias so that M₁/M₂ never enter triode, as in class‑C oscillators, in which case a tail capacitor is beneficial.)",
        "format": "markdown",
        "sha256": "03dc40111180cfd21ef7ff8b1fdaccba2c0413c1e7f32feebb8684bd93bbf20d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It misses the central nonmonotonic effect and the class-C peak-current mechanism that can lower phase noise, instead concluding that CT generally worsens it. Its discussion of triode operation as a possible degradation earns partial credit.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 17834,
        "total_tokens": 21690,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16956,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 17834,
        "total_tokens": 21690,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16956,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Short answer:** not necessarily better – it is a trade‑off, and it can even get worse.\n\n**What C_T helps**\n\nThe tail source I_SS is commutated by M₁–M₂ like a mixer. Its noise components near 2ω₀ (and other even harmonics) are therefore translated to ω₀ ± Δω and appear as sidebands on the carrier (about half of this is PM, the rest AM that can become PM through varactor/AM‑PM conversion). If 1/(2ω₀C_T) is much smaller than the impedance looking into the sources of M₁/M₂ (≈1/g_m), C_T bypasses this high‑frequency tail noise to ground, so the phase‑noise contribution of I_SS at 2ω₀ drops. (Its low‑frequency 1/f noise is not affected – C_T is an open at those frequencies.)\n\n**What C_T hurts**\n\nC_T also makes node P an ac ground at ω₀ and 2ω₀, so the pair loses the \"isolation\" that the high‑impedance current source normally provides:\n\n- With only I_SS at the tail, when M₁ (or M₂) enters the triode region it still just carries I_SS; node P follows V_X and the tank is not loaded. With C_T present, the channel resistance R_on of the triode device appears between the tank node and ground (through C_T) during part of every cycle. The tank Q is degraded (and the swing may drop), which raises the phase noise of all other contributors.\n- Likewise, the drain‑noise current of the transistor that is \"on\" could not reach the tank before (an ideal current source forces its current to I_SS, so the noise only modulated V_P). Now that noise flows through C_T into the tank for the whole half‑cycle, not just around the zero crossings.\n- (Secondary) a tail capacitance also makes ω₀ depend on I_SS, so flicker noise of the tail is upconverted more strongly to 1/f³ phase noise.\n\n**Net result**\n\nThe tail‑noise term at 2ω₀ is reduced, but Q degradation and direct noise injection increase; in a hard‑switched oscillator with large swing the overall phase noise often does not improve and may degrade. This is why a plain tail capacitor is not the preferred fix: one instead keeps a large capacitor across the current source but inserts an inductor between it and node P that resonates with the tail capacitance at 2ω₀ (tail \"noise filter\"), so P sees a high impedance at 2ω₀ while the source noise at 2ω₀ is still shunted – or one biases the pair so M₁, M₂ never enter the triode region.",
        "format": "markdown",
        "sha256": "be936651ce6ba8d703902b5ed62c0123e4a50ef06b427de77f3f80d447f9bc46"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes a possible tradeoff and that phase noise can worsen, but misses the key class-C mechanism in which peak tank currents exceed ISS and can improve phase noise. Its loading, direct-noise-injection, and tail-flicker explanations do not establish Razavi’s CT-dependent nonmonotonic behavior.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 18912,
        "total_tokens": 22768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3856,
        "output_tokens": 18912,
        "total_tokens": 22768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the circuit**\n\nThe figure is a quadrature oscillator: two identical LC cross‑coupled oscillators (tail current I_SS each) coupled by two differential pairs (tail current I₁ each). Oscillator 2's output drives the coupling pair of oscillator 1 directly, while oscillator 1's output drives the coupling pair of oscillator 2 with the gates swapped – i.e., \"anti‑phase\" coupling. Because of this coupling, the circuit does **not** oscillate at the tank resonance ω₀ = 1/√(LC).\n\n**Derivation**\n\nLet V₁ and V₂ be the differential tank voltages. With large swings both differential pairs switch completely, so the fundamental of the current each pair delivers to a tank is proportional to its tail current:\n\n- cross‑coupled pair: ∝ I_SS, in phase with its own tank voltage (negative‑resistance action)\n- coupling pair: ∝ I₁, in phase with the *other* oscillator's voltage\n\nThus\n\nI_T1 = a V₁ + b V₂ ,  I_T2 = a V₂ − b V₁ ,  with b/a = I₁/I_SS .\n\nSince V₁ = Z(ω)I_T1 and V₂ = Z(ω)I_T2 with the same tank impedance Z:\n\nV₁/V₂ = (aV₁ + bV₂)/(aV₂ − bV₁) ⇒ V₁² = −V₂² ⇒ V₂ = ±jV₁ .\n\nSo the two oscillators lock in quadrature, and the total current flowing into each tank is\n\nI_T = (a ± jb)V₁ ,\n\ni.e., it leads/lags the tank voltage by θ = tan⁻¹(I₁/I_SS). For the loop to be consistent, each tank must supply the opposite phase shift, which a parallel RLC can do only off resonance:\n\n∠Z(ω) = −tan⁻¹[2Q(ω − ω₀)/ω₀] = ∓θ  ⇒  2Q(ω_osc − ω₀)/ω₀ = ±I₁/I_SS .\n\n**Result**\n\n$$\n\\omega_{osc}\\;\\approx\\;\\omega_0\\;\\pm\\;\\frac{\\omega_0}{2Q}\\,\\frac{I_1}{I_{SS}},\\qquad \n\\omega_0=\\frac{1}{\\sqrt{LC}},\\; Q=\\frac{R_p}{L\\omega_0}\n$$\n\n(exactly, ω_osc/ω₀ = √(1+(I₁/2QI_SS)²) ± I₁/(2QI_SS)).\n\nSo the oscillation frequency is pulled away from the tank resonance by roughly (ω₀/2Q)(I₁/I_SS); the circuit can run in either of two modes (above or below ω₀, depending on which output leads by 90°), and because the tanks operate off resonance the phase noise is worse than that of a single free‑running oscillator.",
        "format": "markdown",
        "sha256": "af777744b156e43c48f32a876ba79f31ee0a3377538588870fbfab9c890fa1d3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives the tank resonance and the coupling-induced shift \u00177\u0003c9\u000b0(I\b/I\u000bSS)/(2Q), including the two possible modes above or below resonance. The derivation is consistent with the required large-signal estimate.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 16261,
        "total_tokens": 18270,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15255,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 16261,
        "total_tokens": 18270,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15255,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the circuit**\n\nThe figure shows two identical cross‑coupled LC oscillators (tail currents $I_{SS}$) that are coupled to each other by differential pairs (tail currents $I_1$):\n\n- the coupling pair of the bottom oscillator is driven by $(X_1 ,Y_1)$ directly, \n- the coupling pair of the top oscillator is driven by $(Y_2 ,X_2)$, i.e. with an inversion.\n\nThus the loop formed by the two oscillators contains one net sign inversion (\"anti‑phase coupling\"), which is the standard quadrature oscillator: in steady state $V_{X2}-V_{Y2}=\\pm j\\,(V_{X1}-V_{Y1})$.\n\n**Why the frequency is not $\\omega_0$**\n\nLet each tank have $L_1$, total node capacitance $C_1$, parallel loss $R_p$, $\\omega_0=1/\\sqrt{L_1C_1}$, $Q=R_p/(L_1\\omega_0)$.\n\nWith complete switching:\n\n- the cross‑coupled pair steers $I_{SS}$ at the zero crossings of its *own* tank voltage, so its differential current (fundamental $\\frac{4}{\\pi}I_{SS}$) is **in phase** with $V_1$;\n- the coupling pair steers $I_1$ at the zero crossings of the *other* oscillator's voltage, which is in quadrature, so its fundamental $\\frac{4}{\\pi}I_1$ is at $\\pm 90^\\circ$ with respect to $V_1$.\n\nThe total current driving tank 1 is therefore (phasor) $I_T=\\frac{4}{\\pi}(I_{SS}\\pm jI_1)$, which makes an angle $\\theta=\\tan^{-1}(I_1/I_{SS})$ with $V_1$. Since $V_1=Z_T(j\\omega)\\,I_T$, the tank itself must supply a phase shift of $\\mp\\theta$, i.e. it must operate **off resonance**:\n\n$$\\angle Z_T(j\\omega_{osc})=\\mp\\tan^{-1}\\frac{I_1}{I_{SS}}.$$\n\n(Equivalently, in small‑signal terms the loop condition gives $Z_T\\,(g_m\\pm j g_{m,c})=1$, with coupling factor $\\alpha=g_{m,c}/g_m\\approx I_1/I_{SS}$.)\n\n**Solving for the frequency**\n\nFor the parallel tank, \n$$Z_T=\\frac{R_p}{1+jQ\\left(\\dfrac{\\omega}{\\omega_0}-\\dfrac{\\omega_0}{\\omega}\\right)}\\approx\\frac{R_p}{1+j\\,2Q\\dfrac{\\omega-\\omega_0}{\\omega_0}},$$\nso $\\angle Z_T\\approx-\\tan^{-1}\\!\\left[2Q(\\omega-\\omega_0)/\\omega_0\\right]$. Equating with the required phase:\n\n$$2Q\\,\\frac{\\omega_{osc}-\\omega_0}{\\omega_0}=\\pm\\frac{I_1}{I_{SS}}$$\n\n$$\\boxed{\\;\\omega_{osc}\\approx\\omega_0\\left(1\\pm\\frac{1}{2Q}\\,\\frac{I_1}{I_{SS}}\\right)=\\frac{1}{\\sqrt{L_1C_1}}\\left(1\\pm\\frac{\\alpha}{2Q}\\right),\\qquad \\alpha\\approx\\frac{I_1}{I_{SS}}\\;}$$\n\n(exactly, $\\omega_{osc}=\\omega_0\\left[\\sqrt{1+\\left(\\tfrac{I_1}{2QI_{SS}}\\right)^2}\\pm\\tfrac{I_1}{2QI_{SS}}\\right]$).\n\nSo the circuit does **not** oscillate at the tank resonance but is pulled above or below $\\omega_0$ by a fractional amount $(I_1/I_{SS})/(2Q)$; which of the two modes (the $+$ or $-$ sign, corresponding to $V_2$ leading or lagging $V_1$ by $90^\\circ$) actually occurs depends on start‑up conditions/asymmetries. Because the tanks run off resonance, their effective Q is reduced, which is the well‑known phase‑noise penalty of this quadrature topology.",
        "format": "markdown",
        "sha256": "ec1eb12f9d7bdb2b855323d3051a54a2eebcf26ae7458bbe251abb199e4c0258"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives the tank resonance and the coupling-induced shift, \u001b[?]",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 21237,
        "total_tokens": 23246,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19745,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 21237,
        "total_tokens": 23246,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19745,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-fable-5.1",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Recognizing the circuit**\n\nEach half is a cross‑coupled LC oscillator (inner pair, tail current $I_{SS}$). The outer pairs (tail current $I_1$) couple the two oscillators:\n\n- Top tank: the device at $X_1$ is driven by $Y_2$, the device at $Y_1$ by $X_2$ → current injected into tank 1 $\\propto +(V_{X2}-V_{Y2}) = +V_2$\n- Bottom tank: the device at $X_2$ is driven by $X_1$, the device at $Y_2$ by $Y_1$ → current injected into tank 2 $\\propto -(V_{X1}-V_{Y1}) = -V_1$\n\nThe coupling signs are opposite (\"anti‑phase\" coupling), so the only self‑consistent solution is $V_2=\\pm jV_1$: the outputs are in quadrature, and this forces the tanks to run off resonance.\n\n**Phase condition**\n\nIn steady state both pairs switch completely. In each tank the core pair delivers a square‑wave current (fundamental $\\tfrac{4}{\\pi}I_{SS}$) in phase with that tank's own voltage, while the coupling pair delivers a square wave (fundamental $\\tfrac{4}{\\pi}I_1$) that is 90° out of phase (because it follows the other, quadrature, tank). The total tank current is therefore\n\n$$\nI_{tank}=\\frac{4}{\\pi}\\left(I_{SS}\\pm jI_1\\right),\\qquad \\angle I_{tank}=\\pm\\tan^{-1}\\frac{I_1}{I_{SS}} .\n$$\n\nFor the tank voltage to be in phase with the core current, the tank impedance must supply the opposite phase, $\\mp\\tan^{-1}(I_1/I_{SS})$. For a parallel RLC tank,\n\n$$\n\\angle Z_{tank}=-\\tan^{-1}\\!\\left[Q\\left(\\frac{\\omega}{\\omega_0}-\\frac{\\omega_0}{\\omega}\\right)\\right]\\approx-\\tan^{-1}\\!\\left(\\frac{2Q\\,\\Delta\\omega}{\\omega_0}\\right),\n\\qquad \\omega_0=\\frac{1}{\\sqrt{L_1C_1}}\n$$\n\n(with $C_1$ the total capacitance at each output node).\n\n**Result**\n\n$$\n\\frac{2Q\\,\\Delta\\omega}{\\omega_0}=\\pm\\frac{I_1}{I_{SS}}\n\\;\\;\\Longrightarrow\\;\\;\n\\boxed{\\;\\omega_{osc}\\approx\\omega_0\\left(1\\pm\\frac{1}{2Q}\\,\\frac{I_1}{I_{SS}}\\right)=\\frac{1}{\\sqrt{L_1C_1}}\\left(1\\pm\\frac{I_1}{2Q\\,I_{SS}}\\right)\\;}\n$$\n\n(exactly: $Q(\\omega_{osc}/\\omega_0-\\omega_0/\\omega_{osc})=\\pm I_1/I_{SS}$).\n\nSo the quadrature oscillator does **not** run at the tank resonance; it is pulled above or below $\\omega_0$ by $(I_1/I_{SS})\\,\\omega_0/(2Q)$. The weaker the coupling ($I_1\\ll I_{SS}$) the smaller the shift; for $I_1=I_{SS}$ the tanks must provide 45° and $\\omega_{osc}=\\omega_0\\pm\\omega_0/(2Q)$. Which of the two frequencies the circuit actually chooses depends on which mode has the slightly higher loop gain (tank asymmetry, delays) — the well‑known mode ambiguity of quadrature oscillators.",
        "format": "markdown",
        "sha256": "7207c1c3a9e1b59b67c72ab55f828027dbfab0d98b2919611e5f484d3ce02410"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It gives the tank resonance and the coupling-induced shift Δω ≈ (I1/ISS)ω0/(2Q), matching the required large-signal estimate. The added phase derivation and either-side ambiguity do not undermine the result.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 13920,
        "total_tokens": 15929,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12654,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2009,
        "output_tokens": 13920,
        "total_tokens": 15929,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12654,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    }
  ]
}
