{
  "model_key": "claude_sonnet_45",
  "display_name": "Claude Sonnet 4.5",
  "provider": "anthropic",
  "evaluation_model_ids": [],
  "thinking_effort": "max",
  "configuration_note": "Claude Sonnet 4.5 answered the 50 tasks in three rollouts through OpenRouter's chat completions route (anthropic/claude-sonnet-4.5) at maximum reasoning effort. Requests set max_tokens to 64,000, the model's output limit. Each request was one user message holding only the question text and its figure: no title, headings or system prompt. Answers cut off at the output limit were re-run; every attempt is counted in tokens and cost. Answers were graded by GPT-6 Luna at maximum reasoning effort. Cost uses OpenRouter's list price for Claude Sonnet 4.5 on 2026-11-10 ($3.00 input, $0.30 cached input, $15.00 output per 1M tokens).",
  "mode": "direct_qa",
  "summary": {
    "rollout_count": 3,
    "answer_count": 150,
    "scores": {
      "overall": {
        "gpt_6_luna_max": {
          "response_count": 150,
          "correct_count": 36,
          "incorrect_count": 114,
          "partial_credit_count": 70,
          "zero_count": 44,
          "mean_score_0_to_4": 1.7666666666666666,
          "score_percent": 44.166666666666664,
          "score_distribution": {
            "0": 44,
            "1": 34,
            "2": 21,
            "3": 15,
            "4": 36
          }
        },
        "active": {
          "response_count": 150,
          "correct_count": 36,
          "incorrect_count": 114,
          "partial_credit_count": 70,
          "zero_count": 44,
          "mean_score_0_to_4": 1.7666666666666666,
          "score_percent": 44.166666666666664,
          "score_distribution": {
            "0": 44,
            "1": 34,
            "2": 21,
            "3": 15,
            "4": 36
          }
        }
      },
      "part1": {
        "gpt_6_luna_max": {
          "response_count": 90,
          "correct_count": 29,
          "incorrect_count": 61,
          "partial_credit_count": 26,
          "zero_count": 35,
          "mean_score_0_to_4": 1.788888888888889,
          "score_percent": 44.72222222222222,
          "score_distribution": {
            "0": 35,
            "1": 11,
            "2": 11,
            "3": 4,
            "4": 29
          }
        },
        "active": {
          "response_count": 90,
          "correct_count": 29,
          "incorrect_count": 61,
          "partial_credit_count": 26,
          "zero_count": 35,
          "mean_score_0_to_4": 1.788888888888889,
          "score_percent": 44.72222222222222,
          "score_distribution": {
            "0": 35,
            "1": 11,
            "2": 11,
            "3": 4,
            "4": 29
          }
        }
      },
      "part2": {
        "gpt_6_luna_max": {
          "response_count": 60,
          "correct_count": 7,
          "incorrect_count": 53,
          "partial_credit_count": 44,
          "zero_count": 9,
          "mean_score_0_to_4": 1.7333333333333334,
          "score_percent": 43.333333333333336,
          "score_distribution": {
            "0": 9,
            "1": 23,
            "2": 10,
            "3": 11,
            "4": 7
          }
        },
        "active": {
          "response_count": 60,
          "correct_count": 7,
          "incorrect_count": 53,
          "partial_credit_count": 44,
          "zero_count": 9,
          "mean_score_0_to_4": 1.7333333333333334,
          "score_percent": 43.333333333333336,
          "score_distribution": {
            "0": 9,
            "1": 23,
            "2": 10,
            "3": 11,
            "4": 7
          }
        }
      }
    },
    "by_rollout": {
      "1": {
        "response_count": 50,
        "correct_count": 12,
        "incorrect_count": 38,
        "partial_credit_count": 25,
        "zero_count": 13,
        "mean_score_0_to_4": 1.86,
        "score_percent": 46.5,
        "score_distribution": {
          "0": 13,
          "1": 11,
          "2": 8,
          "3": 6,
          "4": 12
        }
      },
      "2": {
        "response_count": 50,
        "correct_count": 10,
        "incorrect_count": 40,
        "partial_credit_count": 27,
        "zero_count": 13,
        "mean_score_0_to_4": 1.74,
        "score_percent": 43.5,
        "score_distribution": {
          "0": 13,
          "1": 13,
          "2": 8,
          "3": 6,
          "4": 10
        }
      },
      "3": {
        "response_count": 50,
        "correct_count": 14,
        "incorrect_count": 36,
        "partial_credit_count": 18,
        "zero_count": 18,
        "mean_score_0_to_4": 1.7,
        "score_percent": 42.5,
        "score_distribution": {
          "0": 18,
          "1": 10,
          "2": 5,
          "3": 3,
          "4": 14
        }
      }
    },
    "tokens": {
      "response_count": 150,
      "usage_record_count": 150,
      "complete_usage_count": 150,
      "missing_usage_count": 0,
      "missing_cached_input_count": 0,
      "complete": true,
      "totals": {
        "cached_input_tokens": 0,
        "input_tokens": 205227,
        "output_tokens": 461388,
        "total_tokens": 666615
      },
      "known_totals": {
        "cached_input_tokens": 0,
        "input_tokens": 205227,
        "output_tokens": 461388,
        "total_tokens": 666615
      }
    },
    "by_rollout_part": {
      "part1": {
        "1": {
          "response_count": 30,
          "correct_count": 9,
          "incorrect_count": 21,
          "partial_credit_count": 12,
          "zero_count": 9,
          "mean_score_0_to_4": 1.8666666666666667,
          "score_percent": 46.666666666666664,
          "score_distribution": {
            "0": 9,
            "1": 5,
            "2": 6,
            "3": 1,
            "4": 9
          }
        },
        "2": {
          "response_count": 30,
          "correct_count": 9,
          "incorrect_count": 21,
          "partial_credit_count": 10,
          "zero_count": 11,
          "mean_score_0_to_4": 1.8333333333333333,
          "score_percent": 45.83333333333333,
          "score_distribution": {
            "0": 11,
            "1": 4,
            "2": 3,
            "3": 3,
            "4": 9
          }
        },
        "3": {
          "response_count": 30,
          "correct_count": 11,
          "incorrect_count": 19,
          "partial_credit_count": 4,
          "zero_count": 15,
          "mean_score_0_to_4": 1.6666666666666667,
          "score_percent": 41.66666666666667,
          "score_distribution": {
            "0": 15,
            "1": 2,
            "2": 2,
            "4": 11
          }
        }
      },
      "part2": {
        "1": {
          "response_count": 20,
          "correct_count": 3,
          "incorrect_count": 17,
          "partial_credit_count": 13,
          "zero_count": 4,
          "mean_score_0_to_4": 1.85,
          "score_percent": 46.25,
          "score_distribution": {
            "0": 4,
            "1": 6,
            "2": 2,
            "3": 5,
            "4": 3
          }
        },
        "2": {
          "response_count": 20,
          "correct_count": 1,
          "incorrect_count": 19,
          "partial_credit_count": 17,
          "zero_count": 2,
          "mean_score_0_to_4": 1.6,
          "score_percent": 40.0,
          "score_distribution": {
            "0": 2,
            "1": 9,
            "2": 5,
            "3": 3,
            "4": 1
          }
        },
        "3": {
          "response_count": 20,
          "correct_count": 3,
          "incorrect_count": 17,
          "partial_credit_count": 14,
          "zero_count": 3,
          "mean_score_0_to_4": 1.75,
          "score_percent": 43.75,
          "score_distribution": {
            "0": 3,
            "1": 8,
            "2": 3,
            "3": 3,
            "4": 3
          }
        }
      }
    }
  },
  "answers": [
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect on Intrinsic Gain\n\nWhen you **double both length (L) and width (W)** of a MOSFET, the **intrinsic gain doubles**.\n\n## Analysis\n\nThe intrinsic gain is: **A₀ = gₘ · r₀**\n\n### Impact on Transconductance (gₘ)\n\n$$g_m = \\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_T)$$\n\n- When W → 2W and L → 2L\n- The ratio W/L remains constant\n- At the same bias point: **gₘ stays the same**\n\n### Impact on Output Resistance (r₀)\n\n$$r_o = \\frac{V_A}{I_D}$$\n\nwhere the Early voltage **V_A ∝ L**\n\n- When L → 2L: V_A → 2V_A\n- Since W/L is unchanged: I_D remains constant\n- Therefore: **r₀ doubles**\n\n### Result\n\n$$A_0' = g_m' \\cdot r_o' = g_m \\cdot (2r_o) = 2A_0$$\n\n## Key Insight\n\nThe intrinsic gain can be expressed as:\n$$A_0 = \\frac{2V_A}{V_{eff}} \\propto L$$\n\nThe intrinsic gain is **directly proportional to channel length**. Since we're maintaining the W/L ratio (and thus the same current at the same bias), the gain improvement comes entirely from the increased output resistance due to reduced channel-length modulation in the longer device.",
        "format": "markdown",
        "sha256": "dccd6b63dfb3e2a2cb0a06fb9542ddb5f3ba4ab698a50cd822af168eab4ca0c0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that intrinsic gain approximately doubles: W/L and overdrive remain unchanged, so gm and ID stay approximately constant, while ro increases with channel length.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 1552,
        "total_tokens": 1611,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1162,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 1552,
        "total_tokens": 1611,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1162,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect on Intrinsic Gain\n\nWhen you **double both length (L) and width (W)** of a MOSFET, the **intrinsic gain doubles** (increases by 2×).\n\n## Analysis\n\nThe intrinsic gain is defined as:\n$$A_v = g_m \\cdot r_o$$\n\nLet me trace through what happens to each parameter:\n\n### Drain Current\nWith constant $V_{GS}$ and $V_{DS}$:\n$$I_D = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}(V_{GS}-V_T)^2$$\n\nWhen W → 2W and L → 2L, the W/L ratio stays constant, so **$I_D$ remains unchanged**.\n\n### Transconductance\n$$g_m = \\mu_n C_{ox}\\frac{W}{L}(V_{GS}-V_T)$$\n\nSince W/L ratio is unchanged and $V_{GS}$ is constant, **$g_m$ remains unchanged**.\n\n### Output Resistance\n$$r_o = \\frac{1}{\\lambda I_D}$$\n\nThe channel-length modulation parameter scales as:\n$$\\lambda \\propto \\frac{1}{L}$$\n\nWhen L → 2L: $\\lambda' = \\lambda/2$\n\nSince $I_D$ is unchanged:\n$$r_o' = \\frac{1}{(\\lambda/2) I_D} = 2r_o$$\n\n### Result\n$$A_v' = g_m' \\cdot r_o' = g_m \\cdot (2r_o) = 2A_v$$\n\n**The intrinsic gain doubles** because the output resistance doubles while transconductance stays constant. This reflects the fundamental relationship: **$A_v \\propto L$** (longer channels have better intrinsic gain).",
        "format": "markdown",
        "sha256": "08a2a27b4c8bb741a94f5fb9ee70b89919f7b58c9c3d3ed4e0f572a269849fce"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that doubling W and L preserves W/L, so gm and drain current stay approximately constant, while the longer channel roughly halves λ and doubles ro and intrinsic gain. Its stated fixed-bias assumptions are consistent with the result.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 2048,
        "total_tokens": 2107,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1597,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 2048,
        "total_tokens": 2107,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1597,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect on Intrinsic Gain\n\nWhen you **double both length (L) and width (W)** of a MOSFET, the **intrinsic gain doubles**.\n\n## Analysis\n\nThe intrinsic gain is: **Av = gm × ro**\n\n### Effect on Transconductance (gm)\n\n$$g_m = \\sqrt{2\\mu_n C_{ox} \\frac{W}{L} I_D}$$\n\n- When W → 2W and L → 2L: **W/L ratio stays constant**\n- At constant bias voltage (VGS, VDS), the drain current ID remains unchanged\n- Therefore: **gm remains the same**\n\n### Effect on Output Resistance (ro)\n\n$$r_o = \\frac{1}{\\lambda I_D}$$\n\nwhere λ (channel length modulation parameter) ∝ 1/L\n\n- When L doubles: λ → λ/2\n- Since ID is constant: **ro doubles**\n\n### Result\n\n$$A_v \\propto \\frac{g_m r_o}{1} = g_m \\cdot (2r_o) = 2A_v$$\n\n## Key Insight\n\nAlternatively: \n$$A_v = \\frac{2}{\\lambda V_{ov}} \\propto L$$\n\nThe intrinsic gain is **directly proportional to channel length** because longer channels reduce channel length modulation effects, increasing output resistance. Scaling width proportionally maintains the operating point while preserving the gain improvement from increased length.",
        "format": "markdown",
        "sha256": "e97af6dcedb601153b37c61a997ce22826c0cbe27b01e14c1db31d55ceac5832"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that intrinsic gain approximately doubles: doubling W and L keeps W/L and gm roughly constant while reducing channel-length modulation and roughly doubling ro. The stated bias assumptions are consistent with the golden solution.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 1212,
        "total_tokens": 1271,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 852,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 59,
        "output_tokens": 1212,
        "total_tokens": 1271,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 852,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at the fundamental MOSFET equations in saturation:\n\n## Key Relationships\n\nThe drain current is:\n$$I_D = \\frac{1}{2}\\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_{th})^2 = \\frac{1}{2}\\mu_n C_{ox} \\frac{W}{L}V_{OV}^2$$\n\nThe transconductance is:\n$$g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = \\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_{th})$$\n\nTherefore:\n$$g_m = \\mu_n C_{ox} \\frac{W}{L}V_{OV}$$\n\n## Answer\n\n**Student A is correct.** \n\nTransconductance is **directly proportional** to overdrive voltage. As $V_{OV}$ increases, $g_m$ increases linearly.\n\nThis can also be expressed as:\n$$g_m = \\frac{2I_D}{V_{OV}}$$\n\nWhile this form might seem to suggest $g_m$ decreases with $V_{OV}$, remember that $I_D$ itself increases as $V_{OV}^2$. The net effect is that $g_m$ increases with $V_{OV}$.\n\n**Physical interpretation:** Higher overdrive voltage means stronger channel inversion, allowing greater control of drain current by the gate voltage, hence higher transconductance.",
        "format": "markdown",
        "sha256": "1011d9bc32abb4c5721a068d7779678ec801d872d511f8f4627907c135dbdb6d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed device size and shows that gm is proportional to VOV while ID rises as VOV².",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 924,
        "total_tokens": 993,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 559,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 924,
        "total_tokens": 993,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 559,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Student A is correct.\n\n## Here's why:\n\nThe transconductance of a MOSFET is defined as:\n\n$$g_m = \\frac{\\partial I_D}{\\partial V_{GS}}$$\n\nFor a MOSFET operating in **saturation**, the drain current is:\n\n$$I_D = \\frac{1}{2}\\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_{th})^2 = \\frac{1}{2}\\mu_n C_{ox} \\frac{W}{L}V_{OV}^2$$\n\nwhere $V_{OV} = V_{GS} - V_{th}$ is the overdrive voltage.\n\nTaking the derivative with respect to $V_{GS}$:\n\n$$g_m = \\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_{th}) = \\mu_n C_{ox} \\frac{W}{L}V_{OV}$$\n\n## Conclusion:\n\n**Transconductance is directly proportional to overdrive voltage.** As $V_{OV}$ increases, $g_m$ increases linearly.\n\nThis can also be expressed as:\n$$g_m = \\sqrt{2\\mu_n C_{ox} \\frac{W}{L} I_D}$$\n\nshowing that higher overdrive voltage → higher drain current → higher transconductance.\n\n**Physical intuition:** A larger overdrive voltage creates a stronger channel, making the transistor more responsive to gate voltage changes, hence higher transconductance.",
        "format": "markdown",
        "sha256": "9affd21f132f752d03e6f65f818c1af68ef50daae0c940864f98faa15a3d17ad"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed device size and derives that gm is proportional to VOV in saturation. The fixed-ID caveat for Student B is optional.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 1005,
        "total_tokens": 1074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 631,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 1005,
        "total_tokens": 1074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 631,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Student A is correct\n\nThe transconductance (gm) of a MOSFET **increases** with overdrive voltage.\n\n## The Math\n\nFor a MOSFET in saturation, transconductance is given by:\n\n$$g_m = \\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_{th}) = \\mu_n C_{ox} \\frac{W}{L} V_{OV}$$\n\nWhere $V_{OV} = V_{GS} - V_{th}$ is the overdrive voltage.\n\nThis shows **gm is directly proportional to overdrive voltage**.\n\n## Alternative Expression\n\nTransconductance can also be written as:\n\n$$g_m = \\frac{2I_D}{V_{OV}}$$\n\nWhile this form might *appear* to suggest an inverse relationship, remember that $I_D \\propto V_{OV}^2$, so:\n- As $V_{OV}$ increases, $I_D$ increases as $V_{OV}^2$\n- Therefore $g_m = \\frac{2I_D}{V_{OV}} \\propto \\frac{V_{OV}^2}{V_{OV}} = V_{OV}$\n\n## Physical Intuition\n\nHigher overdrive voltage → stronger channel → more carriers → greater change in drain current for a given gate voltage change → higher transconductance.",
        "format": "markdown",
        "sha256": "16db4b7a474edbf8ea3d1cb6f920a0a4e17f362c7555e047fb7d32d3e9d35624"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A and shows that, for fixed W/L, gm = μCox(W/L)VOV; it also resolves the alternative expression by noting ID rises as VOV².",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 814,
        "total_tokens": 883,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 479,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 69,
        "output_tokens": 814,
        "total_tokens": 883,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 479,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Small-Signal Models: PMOS vs NMOS\n\n## Yes, structurally identical\n\nThe small-signal models of PMOS and NMOS devices have **identical topology and structure**. Both use the same equivalent circuit with:\n\n- Transconductance current source: **gₘvgs**\n- Output resistance: **ro**\n- Capacitances: **Cgs, Cgd, Cdb, Csb**\n- Body effect: **gmb** (if body/source not connected)\n\n## Key Similarities\n\nThe equations for small-signal parameters have the **same form**:\n\n```\ngₘ = 2ID/(VGS - Vth) = √(2μCox(W/L)ID)\nro = |VA|/ID = 1/(λID)\n```\n\n## Important Differences\n\nWhile the **model structure is identical**, the **parameter values** typically differ:\n\n| Parameter | Comparison |\n|-----------|------------|\n| **Mobility (μ)** | μn ≈ 2-3× μp |\n| **gₘ (same size/current)** | gₘ,NMOS > gₘ,PMOS |\n| **Size for same gₘ** | PMOS needs ≈2-3× width |\n\n## Sign Conventions\n\nSome references show different polarities due to:\n- Current direction conventions (PMOS typically has negative VGS, positive VSG)\n- But the small-signal model itself uses the same reference directions\n\n## Bottom Line\n\nThe small-signal model **equivalent circuit is identical**—no need for different models. Just plug in the appropriate parameter values calculated from the DC operating point.",
        "format": "markdown",
        "sha256": "c22292558e59f63807d0da82584307a19bb06886473f5a988beb5d0dd9092538"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same structure and notes the role of sign conventions, satisfying the full-credit rule.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 807,
        "total_tokens": 865,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 409,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 807,
        "total_tokens": 865,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 409,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Small-Signal Models: NMOS vs PMOS\n\n## Yes, they are structurally identical\n\nThe small-signal equivalent circuit topology is **the same** for both NMOS and PMOS devices. Both use:\n\n- **Transconductance (gm)**: voltage-controlled current source\n- **Output resistance (ro)**: drain-to-source resistance\n- **Body-effect transconductance (gmb)**: if body isn't tied to source\n- **Capacitances**: Cgs, Cgd, Cdb, Csb (for AC/high-frequency analysis)\n\n## Important Differences\n\n### 1. **Voltage/Current Polarities**\n- **NMOS**: VGS > 0, VDS > 0, ID flows into drain\n- **PMOS**: VGS < 0, VDS < 0, ID flows out of drain\n- The model structure is the same, but you must account for these polarities in circuit analysis\n\n### 2. **Parameter Values**\nEven with identical dimensions and bias currents:\n- **PMOS has lower mobility** (~2-3× lower than NMOS)\n- **gm is typically smaller** for PMOS at the same W/L\n- **PMOS is usually sized larger** (2-3× width) to match NMOS performance\n\n### 3. **Sign Conventions**\nIn hand analysis, be careful with signs when writing KCL/KVL equations, but the equivalent circuit elements themselves are placed identically.\n\n## Bottom Line\n\nThe **model topology is identical**, but **parameter values differ** due to device physics, and **polarity conventions** must be carefully observed in analysis.",
        "format": "markdown",
        "sha256": "aaa604249b356b0661df2a50a1c5d39a6c46d1b083b1ae923948c2f0c173b50f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same structure as the NMOS model and notes the polarity/sign-convention differences. The additional parameter comments do not undermine the answer.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 931,
        "total_tokens": 989,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 542,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 931,
        "total_tokens": 989,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 542,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, with Important Caveats\n\nThe **small-signal model topology is identical** for PMOS and NMOS devices, but there are key differences in practice:\n\n## Identical Structure\nBoth use the same equivalent circuit with:\n- Transconductance current source: **gm·vgs**\n- Output resistance: **ro** (or rds)\n- Capacitances: Cgs, Cgd, Cdb, Csb\n- Body effect: **gmb·vbs** (if body/substrate is not tied to source)\n\n## Key Differences\n\n### 1. **Parameter Values**\n- **PMOS has lower hole mobility** (μp ≈ 0.3-0.4 × μn)\n- For the same gm, PMOS needs **2-3× larger W/L ratio**\n- This affects chip area and parasitic capacitances\n\n### 2. **Voltage/Current Reference Directions**\n- NMOS: VGS, VDS referenced to source\n- PMOS: Often use VSG, VSD (source as reference)\n- Small-signal analysis uses **magnitudes**, so this is mainly notational\n\n### 3. **Typical Parameter Ranges**\n```\nFor same bias current & L:\n- PMOS needs larger W → larger Cgs, Cgd\n- gm parameters calculated identically\n- ro behaves similarly (depends on λ or VA)\n```\n\n## Practical Takeaway\nUse the **same small-signal model circuit**, but remember:\n- Calculate parameters using the appropriate μ, W/L, and bias point\n- PMOS circuits often need wider transistors to match NMOS performance\n- The model equations are universal; only device physics parameters differ",
        "format": "markdown",
        "sha256": "710d709485242c2bcb7694373673bd91c4edad5ad6bb7df0f3626a39c845666b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same structure as the NMOS model and notes the polarity-convention differences, satisfying the full-credit rule.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 931,
        "total_tokens": 989,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 524,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 58,
        "output_tokens": 931,
        "total_tokens": 989,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 524,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of IX vs VX\n\nLooking at this circuit, I need to analyze a **diode-connected MOSFET** with an additional **series diode**.\n\n## Circuit Configuration\n\n- M1: NMOS transistor with gate and drain connected together (diode-connected)\n- Source: connected to ground  \n- A diode in series between node (gate-drain) and VX\n- The diode allows current to flow from VX → node → MOSFET → ground\n\n## Operating Regions\n\n### Region 1: VX < Vdiode + VTH\n- The diode may conduct, but the voltage at the gate-drain node is too low\n- MOSFET remains in cutoff\n- **IX = 0**\n\n### Region 2: VX ≥ Vdiode + VTH  \n- Assuming the diode conducts with forward voltage Vdiode (≈0.7V)\n- Voltage at gate-drain node: **VA = VX - Vdiode**\n- Since VGS = VDS = VA, the MOSFET operates in saturation\n- **IX = (K/2)(VGS - VTH)² = (K/2)(VX - Vdiode - VTH)²**\n\nwhere K = μnCox(W/L)\n\n## Sketch of IX vs VX\n\n```\n     IX\n      ↑\n      |           ___----\n      |        _-/\n      |     __/\n      |    /\n      | __/\n      |/___________________→ VX\n      0    Vdiode+VTH\n           (~1.2-1.7V)\n```\n\n**Key Features:**\n- **Zero current** for VX < (Vdiode + VTH)\n- **Turn-on** at VX = Vdiode + VTH  \n- **Parabolic increase** following a square-law relationship\n- The curve starts at approximately 1.2-1.7V (depending on device parameters)\n- Current increases as **(VX - Vdiode - VTH)²**\n\nThis creates a nonlinear current-voltage relationship useful in current mirrors and biasing circuits.",
        "format": "markdown",
        "sha256": "0ef48cf98d1743bbbd8603fafbbbd47b93b40ea11bd09723af5e45fb70f7fd8d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The answer correctly recognizes a diode-connected NMOS and predicts a quadratic rise in saturation, but invents a series diode that is not in the circuit. This shifts the turn-on voltage and gives the wrong IX–VX relation; the golden solution caps such topology misreads at 2.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 6190,
        "total_tokens": 7517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5670,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 6190,
        "total_tokens": 7517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5670,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# IX vs VX Characteristic\n\nLooking at this circuit, I can see a **diode-connected MOSFET** (M₁) where the gate and drain are connected together, with current IX flowing through it and voltage VX applied across it.\n\n## Analysis\n\nFor a diode-connected NMOS transistor:\n- VGS = VDS = VX (since gate and drain are shorted)\n- The transistor operates in **saturation** (for VX ≥ VTH)\n\nThe current-voltage relationship is:\n\n**For VX < VTH:** (cutoff region)\n- IX = 0\n\n**For VX ≥ VTH:** (saturation region)\n- IX = (k/2)(VX - VTH)²\n\nwhere k = μnCox(W/L)\n\n## Sketch of IX vs VX\n\n```\n    IX ↑\n       |\n       |         ___---/\n       |      __/\n       |    _/\n       |   /\n       |  /\n       | /\n       |/\n    ---|----------→ VX\n       0  VTH\n```\n\n## Key Features:\n\n1. **For VX < VTH**: IX = 0 (transistor is OFF)\n\n2. **At VX = VTH**: IX begins to flow, with zero slope (smooth transition)\n\n3. **For VX > VTH**: IX increases **quadratically** with VX\n   - This creates a parabolic curve\n   - The slope continuously increases\n\n4. **Characteristic**: This is a nonlinear resistive element with a square-law relationship, typical of a diode-connected MOSFET\n\nThe curve represents the V-I characteristic of a two-terminal device that conducts current in a nonlinear fashion, commonly used in current mirrors and biasing circuits.",
        "format": "markdown",
        "sha256": "b616298ba341933f7cd9bd40a21162d8b23224e701c9767c22b8021be668e079"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, gives approximately zero current below threshold, and describes the quadratic current rise above threshold in saturation.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 1224,
        "total_tokens": 2551,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 790,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 1224,
        "total_tokens": 2551,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 790,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, I need to analyze the configuration where the MOSFET M₁ has its gate and drain connected together (diode-connected) with a diode in series with the voltage source VX.\n\n## Circuit Analysis\n\n**Configuration:**\n- MOSFET M₁ has its source grounded\n- Gate and drain are connected at a common node\n- A diode is in series between VX and the drain/gate node\n- Current IX flows from VX through the diode to the drain\n\n**When the diode is forward-biased:**\n\nUsing KVL: VX = Von + VD\n\nWhere:\n- Von ≈ 0.7V (diode forward voltage)\n- VD = drain voltage = VX - Von\n\nSince gate and drain are connected:\n- VG = VD = VX - Von\n- VGS = VG - 0 = VX - Von\n- VDS = VD - 0 = VX - Von\n\n**MOSFET Operation Region:**\n\nSince VDS = VGS, checking saturation condition:\n- VDS ≥ VGS - VTH → VGS ≥ VGS - VTH ✓\n\nThe MOSFET always operates in saturation when on.\n\n## I-V Characteristic\n\n**For VX < Von + VTH:**\n- IX = 0 (MOSFET is off)\n\n**For VX ≥ Von + VTH:**\n- IX = (K/2)(VGS - VTH)²\n- **IX = (K/2)(VX - Von - VTH)²**\n\n## Sketch\n\n```\nIX ↑\n   |         \n   |              ___----\n   |          __--\n   |       __-\n   |     _-\n   |   _/\n   |  /\n   | /\n   |/________________→ VX\n   0      Von+VTH\n```\n\n**Key Features:**\n1. **Zero current** for VX < Von + VTH\n2. **Turn-on** at VX = Von + VTH (typically ~1.2V)\n3. **Quadratic increase** - parabolic curve for VX > Von + VTH\n4. **Smooth transition** - continuous with zero slope at turn-on\n5. **Increasing slope** - curve becomes steeper as VX increases\n\nThe characteristic resembles a shifted and squared MOSFET I-V curve, with the diode adding Von to the threshold voltage.",
        "format": "markdown",
        "sha256": "1d4a80b4eda312319d0cf283ead28c9fba831bb2dae52996153e83607ff1f1e2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The answer correctly identifies diode-connected NMOS saturation and a quadratic rise, but invents a series diode, shifting the turn-on from VTH to Von + VTH. This misreads the circuit and gives the wrong threshold.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 10564,
        "total_tokens": 11891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9969,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1327,
        "output_tokens": 10564,
        "total_tokens": 11891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9969,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of IX vs VX Characteristic\n\nLooking at this circuit, I need to analyze the MOSFET M₁ behavior as VX varies.\n\n## Circuit Configuration:\n- VGS = VX (gate voltage, since source is grounded)\n- VDS = 1V (drain connected to 1V supply, source grounded)\n- VS = 0V\n\n## Operating Regions:\n\n### **Region 1: Cutoff (VX < Vth)**\n- Transistor is OFF\n- **IX = 0**\n\n### **Region 2: Saturation (Vth ≤ VX ≤ 1V + Vth)**\n- Condition: VDS ≥ VGS - Vth → 1V ≥ VX - Vth\n- **IX = ½μnCox(W/L)(VX - Vth)²** (quadratic)\n\n### **Region 3: Triode (VX > 1V + Vth)**\n- Condition: VDS < VGS - Vth → 1V < VX - Vth\n- **IX = μnCox(W/L)[(VX - Vth)·1V - 0.5V²]** (linear)\n\n## Sketch:\n\n```\n    IX\n    |\n    |         ___----  (Linear in triode)\n    |      _,/\n    |    ,/\n    |  ,/  (Parabolic in saturation)\n    | /\n    |/__________________ VX\n    0    Vth    (1V+Vth)\n```\n\n## Key Features:\n1. **Zero current** for VX < Vth\n2. **Parabolic increase** starting at VX = Vth (saturation region)\n3. **Linear increase** starting at VX = (1V + Vth) (triode region)\n4. **Smooth transition** at the saturation-triode boundary\n5. The curve is continuous with continuous derivative\n\nFor typical Vth ≈ 0.4-0.7V, the transition to triode occurs around VX = 1.4-1.7V.",
        "format": "markdown",
        "sha256": "4f8d3d5129f7883b0fcf2b59d8f77ca5a38850b008fd5b51b33646d360508a50"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the cutoff, quadratic saturation rise, and transition at VX = VTH + 1 V to a linear triode-region rise, with the appropriate current expressions.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 3435,
        "total_tokens": 4916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2909,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 3435,
        "total_tokens": 4916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2909,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of IX vs VX\n\nLooking at this circuit, I need to determine how the transistor M₁ operates as VX varies.\n\n## Circuit Configuration:\n- **VGS = VX** (gate-source voltage)\n- **VDS = 1V** (drain-source voltage is fixed by the 1V supply)\n- **VS = 0V** (source is grounded)\n\n## Operating Regions:\n\n### 1) **Cutoff Region** (VX < Vth)\n- Transistor is OFF\n- **IX = 0**\n\n### 2) **Saturation Region** (VX ≥ Vth and VDS ≥ VGS - Vth)\n- Condition: Vth ≤ VX ≤ (1 + Vth)\n- **IX = ½ · k · (VX - Vth)²**\n- where k = μₙCox(W/L)\n- Quadratic relationship\n\n### 3) **Triode Region** (VX > Vth and VDS < VGS - Vth)\n- Condition: VX > (1 + Vth)\n- **IX = k · [(VX - Vth) - 0.5]**\n- Linear relationship\n\n## Sketch of IX vs VX:\n\n```\n    IX ↑\n       |           \n       |              /\n       |            /  (Linear - Triode)\n       |          /\n       |        / (Quadratic - Saturation)\n       |      /\n       |    /\n       |  /\n       |/__________|__________|_________→ VX\n       0         Vth      (1+Vth)\n```\n\n**Key Features:**\n- **Region 1** (VX < Vth): Flat line at IX = 0\n- **Region 2** (Vth to 1+Vth): Smoothly increasing parabolic curve\n- **Region 3** (VX > 1+Vth): Linear increase with constant slope k\n- Smooth, continuous transition at VX = 1 + Vth\n\nFor typical Vth ≈ 0.4-0.7V, the transition occurs around VX ≈ 1.4-1.7V.",
        "format": "markdown",
        "sha256": "e579eaa8b167749a49b4940fc34e76a98e2787ad9500261516c8d131b095717e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies cutoff below threshold, quadratic saturation current up to VX = Vth + 1 V, and a continuous, roughly linear triode-region rise beyond it. The current expressions are consistent with VDS = 1 V.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 2370,
        "total_tokens": 3851,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1816,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 2370,
        "total_tokens": 3851,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1816,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of IX vs VX\n\nLooking at this circuit, I need to identify the key voltages:\n- **VGS = VX** (gate-to-source voltage)\n- **VDS = 1V** (drain-to-source voltage, fixed by the battery)\n\nSince VDS is constant at 1V, the transistor will operate in different regions as VX varies.\n\n## Operating Regions\n\n### 1. **Cutoff Region** (VX < Vth)\n- Transistor is OFF\n- **IX = 0**\n\n### 2. **Saturation Region** (Vth ≤ VX ≤ Vth + 1V)\n- Condition: VDS ≥ VGS - Vth → 1 ≥ VX - Vth\n- Current: **IX = ½μnCox(W/L)(VX - Vth)²**\n- Quadratic (parabolic) relationship\n\n### 3. **Triode Region** (VX > Vth + 1V)\n- Condition: VDS < VGS - Vth → 1 < VX - Vth\n- Current: **IX = μnCox(W/L)[(VX - Vth) - 0.5]**\n- Linear relationship\n\n## Sketch of IX vs VX\n\n```\n    IX\n     |\n     |                      /\n     |                    /  \n     |                  /    Linear (Triode)\n     |                /      \n     |              •  ← Transition at Vth + 1V\n     |            /\n     |          /    \n     |        /   Parabolic (Saturation)\n     |      /\n     |    /\n     |___•________________________ VX\n         Vth      Vth + 1V\n         \n     Cutoff  |  Saturation  | Triode\n```\n\n## Key Features:\n\n1. **Flat at zero** for VX < Vth\n2. **Smooth parabolic curve** starting at VX = Vth\n3. **Transitions to linear** at VX = Vth + 1V\n4. **Continuous slope** at the transition point (smooth curve)\n\nThe 1V battery essentially creates a \"load line\" that causes the transistor to transition from saturation to triode operation at a specific gate voltage.",
        "format": "markdown",
        "sha256": "faab74ecb6d85f608c5ecdaad2edcbc2487cf6148547bcad45bcfddac8cce494"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies cutoff, the quadratic saturation region up to VX = VTH + 1 V, and the roughly linear triode-region rise beyond it. The triode formula correctly substitutes VDS = 1 V.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 5216,
        "total_tokens": 6697,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4643,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1481,
        "output_tokens": 5216,
        "total_tokens": 6697,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4643,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the Circuit\n\nThe device shown is a **diode-connected MOSFET** (M₁), where the gate and drain are connected together.\n\n## Can it act as a current source?\n\n**No**, this device **cannot** act as a current source.\n\n### Reasoning:\n\n1. **Voltage-dependent current**: In this configuration, the MOSFET operates in saturation with:\n   - V_GS = V_DS = V_D (since source is grounded)\n   - The current follows: I_X = ½ μₙC_ox(W/L)(V_D - V_th)²\n\n2. **Current source requirements**: A true current source should provide constant current regardless of the voltage across it (high output impedance).\n\n3. **Diode-connected behavior**: The current I_X **varies with the square of the voltage** V_D, making it behave like a nonlinear resistor or diode, not a current source.\n\n### What is it used for?\n\nWhile not a current source itself, diode-connected MOSFETs are commonly used to:\n- **Set reference voltages** in current mirror circuits\n- **Establish bias currents** that are then mirrored to other branches\n- Act as **active loads** with better characteristics than resistors\n\nFor an actual MOSFET current source, you would need a configuration where the gate voltage is held constant by an independent reference, allowing the drain current to remain constant over varying drain voltages.",
        "format": "markdown",
        "sha256": "4a4bec653dadbe28b94c426ca2514bd73f25588dafe189f42ded81bf615fe940"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly concludes that a diode-connected device is not a current source and recognizes its voltage-dependent, nonlinear-resistor behavior. However, it misreads M1 as an NMOS with its source grounded; the figure shows a PMOS whose source is the top terminal, and the key reason is its low small-signal impedance (about 1/gm).",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1103,
        "total_tokens": 1706,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 759,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1103,
        "total_tokens": 1706,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 759,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis: Can this device act as a current source?\n\n**No**, this device **cannot** act as a current source by itself.\n\n## What the circuit shows:\n\nThe figure shows a **diode-connected MOSFET** (M₁) where:\n- Gate and drain are connected together\n- Source is grounded\n- Current Ix flows through the device\n\n## Why it's NOT a current source:\n\n1. **Voltage-dependent behavior**: The current through a diode-connected MOSFET follows:\n   $$I_x = \\frac{1}{2}\\mu_n C_{ox} \\frac{W}{L}(V_{GS} - V_T)^2$$\n   \n   Since VGS = VDS, the current strongly depends on the voltage across the device.\n\n2. **Nonlinear resistor**: This configuration acts as a **nonlinear resistor**, not a current source. The current varies significantly with applied voltage.\n\n3. **Current source definition**: A true current source maintains constant current regardless of the voltage across it (high output impedance). This device doesn't have that property.\n\n## What it IS used for:\n\nThis diode-connected MOSFET is typically used as:\n- The **reference branch** in a current mirror\n- A **load device** in amplifiers\n- Part of a biasing circuit\n\nWhen paired with another MOSFET in a current mirror configuration, the *other* transistor can approximate a current source, but this one alone cannot.",
        "format": "markdown",
        "sha256": "d108467d7128c18381989d96aa01cc67cb6c1c3e6d387a197297315aefe5e39f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly concludes that a diode-connected device is a nonlinear, low-impedance element rather than a current source. However, it misreads the figure: M1 is a PMOS with its source at the top, not a grounded-source NMOS, so the golden solution caps the score at 2.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1199,
        "total_tokens": 1802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1199,
        "total_tokens": 1802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis: Can This Device Act as a Current Source?\n\n## Answer: **No**, this specific configuration cannot act as a current source.\n\n## Why Not?\n\nLooking at the circuit, transistor M₁ has:\n- **Gate connected to ground** (left terminal)\n- **Source connected to ground** (right terminal)  \n- **Current Ix flowing into the drain** (top terminal)\n\n### Problems with this configuration:\n\n1. **Vgs = 0V**: With both gate and source at ground potential, the gate-source voltage is zero\n   - For an NMOS: Vgs = 0 < Vth → transistor is **OFF**\n   - For a PMOS: Vgs = 0 > Vth → transistor is **OFF**\n\n2. **No current regulation**: Even if the device were somehow conducting, there's no mechanism to regulate the current independent of voltage changes\n\n3. **No feedback mechanism**: Current sources require some form of feedback (like gate-drain connection or biasing network) to maintain constant current\n\n## What Would Work?\n\nTo make a MOSFET current source, you would typically need:\n- **Diode-connected**: Gate connected to drain\n- **Current mirror**: Proper biasing and reference current\n- **Active biasing**: Fixed gate voltage with appropriate source resistor\n\nThis circuit appears to show an external current Ix being applied, but M₁ in this configuration cannot function as an active current source.",
        "format": "markdown",
        "sha256": "78c3f42b7d1a458ddcd1c31e2fd694364b27815e62c19e39129e4cb9b954c966"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the connections and concludes the device is off from VGS = 0, missing that M1 is a diode-connected PMOS whose low impedance prevents current-source behavior.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1462,
        "total_tokens": 2065,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1128,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 603,
        "output_tokens": 1462,
        "total_tokens": 2065,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1128,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Drain Amplifier (Source Follower)\n\n## Circuit Configuration\n\nThis is a **common-drain amplifier**, also known as a **source follower**. The key identifying features are:\n- Input at the gate (Vin)\n- Output taken from the source (Vout)\n- Drain connected to VDD through Rs\n- Source connected to ground through RD\n\n## DC Analysis\n\n**Operating point equations:**\n\n1. Gate-source voltage: VGS = Vin - Vout = Vin - ID·RD\n2. Drain current (assuming saturation): ID = ½·kn·(VGS - Vth)²\n3. Output voltage: Vout = ID·RD\n4. Power supply loop: VDD = ID·Rs + VDS + ID·RD\n\nThe transistor must satisfy: VDS ≥ VGS - Vth (for saturation region operation)\n\n## AC Small-Signal Analysis\n\n**Voltage Gain:**\n\nUsing small-signal analysis with vgs = vin - vout and id = gm·vgs:\n\n$$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m \\cdot R_D}{1 + g_m \\cdot R_D}$$\n\nThis can be rewritten as:\n$$A_v = \\frac{1}{1 + \\frac{1}{g_m \\cdot R_D}}$$\n\nFor gm·RD >> 1: **Av ≈ 1** (typically 0.8 - 0.95)\n\n**Output Impedance:**\n\n$$R_{out} = R_D \\parallel \\frac{1}{g_m} \\approx \\frac{1}{g_m}$$ \n\n(when RD >> 1/gm)\n\n**Input Impedance:**\n\n$$Z_{in} \\approx \\infty$$ (very high, determined by gate capacitance at high frequencies)\n\n## Key Characteristics\n\n| Parameter | Value/Description |\n|-----------|------------------|\n| Voltage Gain | < 1 (non-inverting) |\n| Input Impedance | Very High |\n| Output Impedance | Low (~1/gm) |\n| Phase Shift | 0° (no inversion) |\n\n## Applications\n\n1. **Buffer amplifier** - impedance transformation\n2. **Voltage follower** - isolate stages\n3. **Level shifting** - DC voltage translation\n4. **Output driver** - drive low-impedance loads\n\n## Role of Components\n\n- **Rs**: Sets DC bias point, provides drain current path\n- **RD**: Determines gain and output DC level\n- **M₁**: Provides voltage gain and impedance transformation",
        "format": "markdown",
        "sha256": "2c92fe480e0faf4c814210f4c4b75c568f013b73ff74fd500903cae4b139e0eb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the PMOS common-source stage as a source follower and gives a non-inverting follower gain instead of the inverting source-degenerated gain.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 2910,
        "total_tokens": 4494,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2256,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 2910,
        "total_tokens": 4494,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2256,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Drain Amplifier (Source Follower)\n\n## **Circuit Configuration**\n\nThis is a **common-drain amplifier**, also known as a **source follower**. The circuit consists of:\n- N-channel MOSFET (M₁)\n- Source resistor (R_S) connecting V_DD to the drain\n- Drain resistor (R_D) connecting the source to ground\n- Input applied to the gate\n- Output taken from the source terminal\n\n## **DC Operating Point Analysis**\n\nAssuming M₁ operates in **saturation region**:\n\n1. **Gate voltage**: V_G = V_in(DC)\n\n2. **Source voltage**: V_S = V_out(DC)\n\n3. **Drain current**: \n   - I_D = (V_DD - V_D)/R_S = V_S/R_D\n   - I_D = ½μ_nC_ox(W/L)(V_GS - V_TH)²\n\n4. **Saturation condition**: V_DS ≥ V_GS - V_TH\n\n## **Small-Signal AC Analysis**\n\n### **Voltage Gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m R_D}{1 + g_m R_D}$$\n\n- If g_m R_D >> 1, then **A_v ≈ 1** (unity gain)\n- The gain is always **less than 1** but approaches unity\n- **No phase inversion** (output follows input)\n\n### **Input Impedance:**\n$$Z_{in} ≈ ∞$$ (extremely high - gate input)\n\n### **Output Impedance:**\n$$Z_{out} = R_D \\parallel \\frac{1}{g_m} ≈ \\frac{1}{g_m}$$ (if R_D >> 1/g_m)\n\n## **Key Characteristics**\n\n✓ **Very high input impedance** - excellent for buffering  \n✓ **Low output impedance** - can drive low-impedance loads  \n✓ **Unity voltage gain** - primarily used for impedance transformation  \n✓ **No phase inversion** - output voltage follows input  \n✓ **Good linearity** - negative feedback through source resistor\n\n## **Applications**\n\n- **Buffer amplifier** / Impedance matching\n- **Level shifting**\n- **Output stage** in multi-stage amplifiers\n- **Voltage follower** applications",
        "format": "markdown",
        "sha256": "85c43aa8453643de3ee2207d3837a317382fd0dd82983dee78c41f27fe57efed"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the PMOS common-source stage with source degeneration as an NMOS source follower, misreads the output node and resistor connections, and gives the wrong gain and phase behavior.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 3731,
        "total_tokens": 5315,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 3731,
        "total_tokens": 5315,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Drain Amplifier (Source Follower)\n\n## **Circuit Configuration**\n\nThis is a **Common-Drain (Source Follower) amplifier** using an NMOS transistor M₁.\n\n**Connections:**\n- **Gate**: Input voltage (Vᵢₙ)\n- **Drain**: Connected to V_DD through R_S\n- **Source**: Connected to ground through R_D, with output (Vₒᵤₜ) taken from this node\n\n## **DC Analysis**\n\n**Operating Point:**\n- Drain current: $I_D = \\frac{V_{DD} - V_{DS}}{R_S} = \\frac{V_{out}}{R_D}$\n- For saturation: $I_D = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}(V_{GS} - V_{TH})^2$\n- Gate-source voltage: $V_{GS} = V_{in} - V_{out}$\n- Output voltage: $V_{out} = I_D \\cdot R_D$\n\n## **AC Analysis**\n\n**Key Parameters:**\n\n1. **Voltage Gain:**\n   $$A_v = \\frac{g_m R_D}{1 + g_m R_D} < 1$$\n   - Approaches unity for large $g_m R_D$\n   - Typically 0.8 - 0.95\n\n2. **Input Impedance:** Very high (~MΩ range) - gate of MOSFET\n\n3. **Output Impedance:** \n   $$Z_{out} \\approx \\frac{1}{g_m} \\parallel R_D \\approx \\frac{1}{g_m}$$\n   - Very low (ideal for driving loads)\n\n## **Circuit Characteristics**\n\n✅ **Advantages:**\n- High input impedance\n- Low output impedance  \n- No phase inversion (Vₒᵤₜ in phase with Vᵢₙ)\n- Excellent buffer/impedance matching\n- Good linearity\n\n⚠️ **Limitations:**\n- Gain less than unity (no voltage amplification)\n- R_S limits voltage swing at the drain\n\n## **Applications**\n- **Buffer amplifier** for impedance matching\n- **Level shifter**\n- **Output stage** in multi-stage amplifiers\n- **Line driver** circuits",
        "format": "markdown",
        "sha256": "35eb4f149498080872414646946bfd374b4b8df9b2388c52f437db51f74f9459"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer fundamentally misidentifies the circuit as an NMOS source follower. The actual circuit is a PMOS common-source stage with source degeneration, so its topology, gain, and phase conclusions are wrong.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 2000,
        "total_tokens": 3584,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1409,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1584,
        "output_tokens": 2000,
        "total_tokens": 3584,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1409,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: NMOS Source Follower\n\n## Circuit Configuration\n\nThis is an **NMOS source follower** (also called a **common-drain amplifier**), consisting of:\n- **M₁**: NMOS transistor\n- **V_DD**: Positive power supply\n- **R_S**: Source resistor (load)\n- **V_in**: Input voltage applied to the gate\n- **V_out**: Output taken from the source terminal\n\n## DC Operating Point Analysis\n\n**Key Relationships:**\n- V_GS = V_in - V_out\n- I_D flows through R_S: V_out = I_D × R_S\n- For saturation operation: V_DS ≥ V_GS - V_th\n\n**DC Equations (assuming saturation):**\n```\nI_D = ½ μₙC_ox(W/L)(V_GS - V_th)²\nV_out = I_D × R_S\nV_GS = V_in - V_out\n```\n\n## Key Characteristics\n\n### 1. **Voltage Gain**\n- A_v ≈ **g_m·R_S / (1 + g_m·R_S) < 1**\n- Typically 0.8 to 0.95\n- Output \"follows\" input with slight attenuation\n\n### 2. **Input/Output Relationship**\n- V_out ≈ V_in - V_GS\n- **No phase inversion**\n- DC level shift downward by V_GS\n\n### 3. **Impedance Characteristics**\n- **Input impedance**: Very high (≈ ∞)\n- **Output impedance**: Low (≈ 1/g_m || R_S)\n\n### 4. **Advantages**\n- Excellent buffer/isolator\n- High input impedance for minimal loading\n- Low output impedance for driving loads\n- Wide bandwidth\n\n## Applications\n- **Voltage buffer**\n- **Impedance matching**\n- **Level shifter**\n- **Output driver stage**\n- **Analog signal processing**",
        "format": "markdown",
        "sha256": "5859d7cefad0f0d87430c56893c672e823b552b623162f5921ec416849b1a068"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the NMOS source follower and gives its positive, less-than-unity gain as gm·RS/(1 + gm·RS). The stated output resistance is also consistent with RS || 1/gm.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 1467,
        "total_tokens": 2755,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 1467,
        "total_tokens": 2755,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Source Degeneration\n\n## Circuit Configuration\n\nThis circuit shows an **N-channel MOSFET (M₁)** configured as a **common-source amplifier with source degeneration**:\n\n- **Input**: Gate terminal (Vᵢₙ)\n- **Output**: Drain terminal (Vₒᵤₜ)  \n- **Source resistor**: Rₛ provides degeneration\n- **Power supply**: Vᴅᴅ\n\n## Key Observations\n\n**Note**: The drain appears to be directly connected to Vᴅᴅ. For this to function as a practical amplifier, there would typically need to be:\n- A drain resistor Rᴅ between Vᴅᴅ and drain, OR\n- An active load (current source), OR\n- An external load at the output\n\nAssuming an implied drain load for analysis:\n\n## DC Operating Point\n\n1. **Drain current**: Iᴅ = (Vᴅᴅ - Vₛ - Vₒᵤₜ)/Rᴅ\n2. **Source voltage**: Vₛ = Iᴅ·Rₛ  \n3. **Gate-source voltage**: Vɢₛ = Vᵢₙ - Vₛ\n\n## Small-Signal AC Characteristics\n\n### Voltage Gain\nWith source degeneration:\n$$A_v = -\\frac{g_m R_D}{1 + g_m R_S}$$\n\nWhere gₘ is the transconductance of M₁.\n\n### Benefits of Source Degeneration (Rₛ):\n\n1. **Stabilizes gain** - reduces dependence on gₘ variations\n2. **Increases linearity** - reduces distortion\n3. **Improves bandwidth** - better frequency response\n4. **Stabilizes bias point** - negative feedback for DC\n5. **Increases input impedance** (at source)\n6. **Trade-off**: Reduces overall gain\n\n### Input Impedance\nVery high (ideally infinite at gate)\n\n### Output Impedance  \nIncreased compared to circuit without Rₓ\n\n## Applications\n- Linear amplification with improved stability\n- IF/RF amplifiers\n- Analog signal processing",
        "format": "markdown",
        "sha256": "4371667ad93a352a68d6722d761ce8c4229ffb7497dec9463a7a578f2a080254"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It misidentifies the source follower as a common-source stage, places the output at the drain, and invents a drain load, giving the wrong gain sign and expression. The topology misread limits the score to 1.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 2116,
        "total_tokens": 3404,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1550,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 2116,
        "total_tokens": 3404,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1550,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Drain Amplifier (Source Follower)\n\n## **Circuit Configuration**\n\nThis is a **common-drain amplifier**, also known as a **source follower**, featuring:\n- MOSFET M₁ (N-channel enhancement mode)\n- Source resistor R_S\n- Input applied to gate (V_in)\n- Output taken from source (V_out)\n- Drain connected directly to V_DD\n\n## **DC Operating Point Analysis**\n\nFor the MOSFET in saturation region:\n\n1. **Drain current:** I_D = ½μₙC_ox(W/L)(V_GS - V_th)²\n\n2. **Output voltage:** V_out = I_D × R_S\n\n3. **Gate-source voltage:** V_GS = V_in - V_out\n\nThe circuit self-biases through R_S, with V_out following V_in by approximately V_GS.\n\n## **AC Small-Signal Analysis**\n\n**Voltage Gain:**\n$$A_v = \\frac{g_m R_S}{1 + g_m R_S} < 1$$\n\nWhen g_mR_S >> 1:\n$$A_v \\approx 1$$\n\n**Input Impedance:** Z_in ≈ ∞ (very high)\n\n**Output Impedance:** Z_out ≈ 1/g_m || R_S ≈ **1/g_m** (low)\n\n## **Key Characteristics**\n\n| Parameter | Value |\n|-----------|-------|\n| Voltage Gain | ≈ 0.8 - 0.95 (< 1) |\n| Phase Shift | 0° (non-inverting) |\n| Input Impedance | Very High |\n| Output Impedance | Low |\n\n## **Applications**\n\n- **Buffer amplifier** for impedance matching\n- **Level shifter** circuits\n- **Output stage** in multi-stage amplifiers\n- **Driving low-impedance loads**\n\n## **Advantages**\n\n✓ Unity gain with no phase inversion  \n✓ Excellent impedance transformation  \n✓ Wide bandwidth  \n✓ Simple biasing",
        "format": "markdown",
        "sha256": "0388883dd1c427667b75a0aded525486681a605e7075a1fcc69e740a07ccb9e8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain as gm·RS/(1 + gm·RS). The output-resistance approximation is also appropriate.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 1153,
        "total_tokens": 2441,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 624,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1288,
        "output_tokens": 1153,
        "total_tokens": 2441,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 624,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source NMOS Amplifier\n\n## Circuit Description\n\nThis is a **common-source amplifier** configuration using an NMOS transistor (M₁) with resistive load (R_D).\n\n## Circuit Components\n- **M₁**: NMOS transistor (active device)\n- **R_D**: Drain resistor (load)\n- **V_DD**: DC power supply\n- **V_in**: Input signal (applied to gate)\n- **V_out**: Output signal (taken from drain)\n\n## DC Analysis\n\n**Operating Point:**\n1. Gate current: I_G ≈ 0 (MOSFET property)\n2. For saturation region operation:\n   - I_D = ½ k_n(V_GS - V_th)²\n   - Where k_n = μ_n C_ox (W/L)\n\n3. **Output voltage:** \n   ```\n   V_out = V_DD - I_D·R_D\n   ```\n\n4. **Saturation condition:** V_DS > V_GS - V_th\n\n## AC Small-Signal Analysis\n\n**Voltage Gain:**\n```\nA_v = -g_m · R_D\n```\nWhere g_m = transconductance = 2I_D/(V_GS - V_th)\n\n**Key Parameters:**\n- **Input Impedance:** Z_in ≈ ∞ (very high, gate draws no DC current)\n- **Output Impedance:** Z_out ≈ R_D\n- **Phase Shift:** 180° (inverting amplifier)\n\n## Characteristics\n\n| Property | Value |\n|----------|-------|\n| Gain | -g_m·R_D (moderate to high) |\n| Input Resistance | Very high |\n| Output Resistance | ~R_D |\n| Bandwidth | Limited by parasitic capacitances |\n\n## Advantages\n- ✓ High input impedance\n- ✓ Voltage gain > 1\n- ✓ Simple topology\n\n## Limitations\n- ✗ Inverting output\n- ✗ Limited output swing\n- ✗ Requires careful biasing",
        "format": "markdown",
        "sha256": "4510ad71e7711d4dc09da877515dcd109aea2c645ee24f095b05bf0d9488531e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source-driven, gate-ac-grounded common-gate stage as a common-source stage. Consequently it gives the wrong input resistance and gain sign; the correct results are approximately Rin = 1/gm and a non-inverting gain.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1487,
        "total_tokens": 2744,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1487,
        "total_tokens": 2744,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 962,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier\n\n## Circuit Type\nThis is a **common-source (CS) amplifier** with resistive load - one of the fundamental building blocks in analog circuit design.\n\n## Circuit Components\n- **M₁**: NMOS transistor (common-source configuration)\n- **R_D**: Drain resistor (load resistor)\n- **V_DD**: Power supply voltage\n- **V_in**: Input signal (applied to gate)\n- **V_out**: Output signal (taken from drain)\n\n## DC Operating Point Analysis\n\nFor M₁ in saturation region:\n\n**Drain Current:**\n$$I_D = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}(V_{GS} - V_{th})^2$$\n\n**Output Voltage:**\n$$V_{out} = V_{DD} - I_D \\cdot R_D$$\n\n**Saturation Condition:**\n$$V_{DS} \\geq V_{GS} - V_{th}$$\n\n## Small-Signal AC Analysis\n\n**Voltage Gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} = -g_m R_D$$\n\nwhere $g_m = \\mu_n C_{ox}\\frac{W}{L}(V_{GS} - V_{th})$ is the transconductance\n\n**Key Parameters:**\n- **Input Impedance:** Very high (~∞) - gate draws negligible current\n- **Output Impedance:** ≈ R_D\n- **Phase Shift:** 180° (inverting amplifier)\n\n## Characteristics\n\n### Advantages:\n- High input impedance\n- Moderate voltage gain\n- Simple biasing\n\n### Limitations:\n- Limited output voltage swing\n- Gain-bandwidth trade-off through R_D selection\n- Inverting configuration\n\n## Design Considerations\n\n1. **Biasing:** Choose V_in (DC) to keep M₁ in saturation\n2. **Gain vs. Swing:** Larger R_D increases gain but reduces output swing\n3. **Headroom:** Ensure V_DS remains adequate for saturation throughout signal swing",
        "format": "markdown",
        "sha256": "118bda5c67ca897c290aade089035bcfd8039e8750ba6ea280fc0cca8e2740a1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source-driven, gate-grounded common-gate stage as a common-source stage, so its input resistance, gain, and phase conclusions are wrong for this circuit.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1282,
        "total_tokens": 2539,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 770,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1282,
        "total_tokens": 2539,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 770,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source MOSFET Amplifier\n\n## Circuit Configuration\n\nThis is a **common-source amplifier** - one of the fundamental MOSFET amplifier configurations. The circuit consists of:\n- **M1**: N-channel MOSFET (enhancement mode)\n- **RD**: Drain load resistor\n- **VDD**: Power supply\n- **Vin**: Input signal (applied to gate)\n- **Vout**: Output signal (taken from drain)\n\n## DC Operating Point Analysis\n\n**Conditions for operation:**\n- When VGS > Vth: MOSFET conducts\n- Drain current: ID = ½μnCox(W/L)(VGS - Vth)² (saturation region)\n- Output voltage: Vout = VDD - ID·RD\n\n**Operating regions:**\n1. **Cutoff** (VGS < Vth): ID = 0, Vout = VDD\n2. **Saturation/Active** (VGS > Vth, VDS ≥ VGS - Vth): Normal amplifier operation\n3. **Triode** (VDS < VGS - Vth): MOSFET acts as voltage-controlled resistor\n\n## AC Small-Signal Analysis\n\n**Voltage Gain:**\n$$A_v = -g_m \\cdot R_D$$\n\nwhere gm = 2ID/(VGS - Vth) is the transconductance\n\n**Key Parameters:**\n- **Input Impedance**: Very high (~∞) - gate draws negligible current\n- **Output Impedance**: ≈ RD (assuming ro >> RD)\n- **Phase Shift**: 180° (inverting amplifier)\n\n## Key Characteristics\n\n✓ **Inverting amplifier** - output is phase-reversed from input  \n✓ **High input impedance** - minimal source loading  \n✓ **Moderate voltage gain** - adjustable via RD or device dimensions  \n✓ **Simple topology** - requires proper DC biasing for linear operation\n\n## Applications\n\n- Audio amplification\n- Signal processing stages  \n- Logic level shifting\n- Analog integrated circuits",
        "format": "markdown",
        "sha256": "f1b6ab274816d228f9a93dc2c0a1a1e98b78a482ac64218adadef4c25b7ab75a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the source-driven, gate-ac-grounded common-gate stage as a common-source stage, so its input impedance, gain sign, and phase conclusions are wrong for the circuit.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1441,
        "total_tokens": 2698,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 928,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1257,
        "output_tokens": 1441,
        "total_tokens": 2698,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 928,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source MOSFET Amplifier\n\n## Circuit Configuration\n\nThis is a **common-source amplifier** using an NMOS transistor (M₁) with:\n- **RD**: Drain load resistor\n- **C₁**: AC coupling capacitor\n- **Vb**: DC gate bias voltage\n- **VDD**: Power supply\n- **Vin**: AC input signal\n- **Vout**: Output taken at the drain\n\n## DC Analysis\n\nWith C₁ acting as an open circuit for DC:\n\n**Bias Conditions:**\n- Gate voltage: **VG = Vb**\n- Source voltage: **VS = 0** (grounded)\n- Gate-source voltage: **VGS = Vb**\n\n**Operating Point (assuming saturation region):**\n- Drain current: **ID = ½Kn(VGS - Vth)²**\n- Drain voltage: **VD = VDD - ID·RD**\n- For saturation: **VDS ≥ VGS - Vth**\n\n## AC Analysis\n\nWith C₁ acting as a short circuit at signal frequencies:\n\n**Voltage Gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} = -g_m \\cdot R_D$$\n\nwhere **gm** is the transconductance:\n$$g_m = \\frac{2I_D}{V_{GS} - V_{th}}$$\n\n**Key Parameters:**\n- **Input Impedance:** Very high (~MΩ range) - gate draws negligible current\n- **Output Impedance:** ≈ RD (neglecting ro)\n- **Phase Shift:** 180° (inverting amplifier)\n\n## Key Characteristics\n\n✅ **Advantages:**\n- High input impedance\n- Voltage gain capability\n- Simple circuit topology\n- Good power gain\n\n⚠️ **Disadvantages:**\n- Poor bias stability (fixed bias)\n- Limited output voltage swing\n- Gain dependent on bias point\n\n## Frequency Response\n\n- **Low-frequency cutoff:** Determined by C₁: **fL ≈ 1/(2πC₁Rin)**\n- **High-frequency cutoff:** Limited by CGS and CGD (Miller effect)\n\n## Applications\n\n- Audio amplifiers\n- Signal conditioning circuits\n- Intermediate amplifier stages\n- RF amplifiers (with appropriate component selection)",
        "format": "markdown",
        "sha256": "9a3feddb62d70f3d51f4de24a5a4786df50c0f2f175f79a2a1ba6c8cd7e8da2a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the input as driving a common-source stage and gives a nonzero gain, missing that Vin is connected to the source node that is hard-shorted to ground.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1593,
        "total_tokens": 3189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1019,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1593,
        "total_tokens": 3189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1019,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source MOSFET Amplifier\n\n## Circuit Configuration\n\nThis is a **common-source amplifier** with the following components:\n- **M₁**: N-channel MOSFET (enhancement mode)\n- **R_D**: Drain load resistor\n- **C₁**: AC coupling capacitor\n- **V_b**: DC bias voltage for the gate\n- **V_in**: AC input signal source\n- **V_DD**: Power supply voltage\n\n## DC Analysis (Bias Point)\n\nWith C₁ blocking DC:\n- **Gate voltage**: V_G = V_b\n- **Gate-source voltage**: V_GS = V_b (source is grounded)\n- **Drain current**: I_D = ½μₙC_ox(W/L)(V_GS - V_th)²\n- **Output DC voltage**: V_out(DC) = V_DD - I_D·R_D\n\nFor saturation mode operation: V_DS ≥ V_GS - V_th\n\n## AC Analysis (Small-Signal)\n\nAt signal frequencies, C₁ acts as a short circuit:\n\n**Voltage Gain:**\n```\nA_v = v_out/v_in = -g_m·R_D\n```\n\nwhere g_m = 2I_D/(V_GS - V_th) is the transconductance\n\n**Key Parameters:**\n- **Input impedance**: Very high (~MΩ to GΩ range)\n- **Output impedance**: Z_out ≈ R_D\n- **Phase shift**: 180° (inverting amplifier)\n\n## Characteristics\n\n**Advantages:**\n- High input impedance (minimal loading on source)\n- Voltage amplification\n- Simple circuit topology\n\n**Disadvantages:**\n- Moderate gain (limited by R_D)\n- Signal inversion\n- Gain depends on bias point stability\n\n## Frequency Response\n\n- **Low-frequency cutoff**: Determined by C₁ and input network\n- **High-frequency cutoff**: Limited by MOSFET parasitic capacitances (C_gs, C_gd - Miller effect)\n\nThis is a fundamental analog amplifier stage used extensively in integrated circuits and discrete designs.",
        "format": "markdown",
        "sha256": "86ffd9c3892ea71ece94728584a5ab7369c3b17ce3b8124f7056628056f353a0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the circuit as common-source and gives a −gmRD gain, missing that Vin is coupled to the source node that is hard-shorted to ground; the ideal gain is zero.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1389,
        "total_tokens": 2985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 861,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1389,
        "total_tokens": 2985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 861,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source MOSFET Amplifier\n\n## Circuit Configuration\n\nThis is a **common-source amplifier** using an NMOS transistor (M₁) with the following key components:\n\n- **M₁**: NMOS transistor (amplifying element)\n- **RD**: Drain load resistor\n- **C₁**: AC coupling capacitor\n- **Vb**: DC bias voltage for the gate\n- **VDD**: Power supply voltage\n- **Vin**: AC input signal\n- **Vout**: Output voltage (taken from drain)\n\n## DC Analysis (Biasing)\n\n1. **Gate bias**: VG = Vb (DC voltage)\n2. **Source**: Connected to ground, so VS = 0\n3. **Gate-to-Source voltage**: VGS = Vb\n4. **Drain current**: ID determined by VGS and transistor parameters\n5. **Output DC level**: Vout(DC) = VDD - ID·RD\n\nThe bias point Vb must satisfy: Vb > Vth (threshold voltage) to turn on the transistor.\n\n## AC Analysis (Signal Operation)\n\n### Signal Flow:\n- AC input signal couples through C₁ to the gate\n- Gate voltage variations modulate the drain current\n- Current changes through RD produce voltage variations at the drain\n- Output is taken from the drain node\n\n### Key Performance Metrics:\n\n**1. Voltage Gain:**\n$$A_v \\approx -g_m \\cdot R_D$$\n\nwhere gm is the transconductance of M₁. The negative sign indicates **180° phase inversion**.\n\n**2. Input Impedance:**\n- Very high (ideally infinite due to MOSFET gate)\n- Practically limited by any gate biasing network\n\n**3. Output Impedance:**\n$$Z_{out} \\approx R_D$$\n\n## Circuit Characteristics\n\n✓ **Inverting amplifier** (output inverts with respect to input)  \n✓ **High input impedance** (minimal loading on source)  \n✓ **Moderate voltage gain** (depends on gm and RD)  \n✓ **Simple single-stage design**  \n\n## Applications\n\n- Audio amplification\n- Signal conditioning\n- Analog signal processing\n- First stage in multi-stage amplifiers",
        "format": "markdown",
        "sha256": "ae50d2090a13207866edd301314d69b4b47e400bf4b0fd13969a810bb7505b41"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the input as coupled to the gate and calls the circuit common-source, missing that Vin is applied to the source node that is directly shorted to ground.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1147,
        "total_tokens": 2743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 602,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 1147,
        "total_tokens": 2743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 602,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this common-source MOSFET amplifier circuit, I need to count the number of poles in the transfer function by identifying all independent energy storage elements (capacitors).\n\n## Identifying the Capacitors\n\nThe circuit contains **four capacitors**:\n\n1. **C_GS** - Gate-to-source capacitance\n2. **C_GD** - Gate-to-drain (Miller) capacitance  \n3. **C_SB** - Source bypass capacitor\n4. **C_DB** - Drain bypass capacitor\n\n## Determining Independence\n\nFor each capacitor to contribute a pole, it must be independent (not simply in series or parallel with others):\n\n- **C_GS**: Connected between gate and source nodes ✓\n- **C_GD**: Connected between gate and drain nodes, creating feedback ✓\n- **C_SB**: Connected between source and ground ✓\n- **C_DB**: Connected between drain (output) and ground ✓\n\nAll four capacitors are in different configurations and cannot be combined into fewer equivalent capacitors.\n\n## Frequency Distribution\n\nThese poles are typically distributed as:\n- **1 low-frequency pole**: from C_SB (source bypass)\n- **3 high-frequency poles**: from C_GS, C_GD, and C_DB\n\n## Answer\n\nThe circuit has **4 poles**.\n\nThis is because the order of the transfer function equals the number of independent energy storage elements, and all four capacitors contribute to the input-output transfer function V_out/V_in.",
        "format": "markdown",
        "sha256": "ad9307ea965a4fe02fcc793dbc5800b807954a9d2eb7b852c27cc2fde6e3ae03"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The pole count is wrong: the source is grounded, so C_SB has no voltage across it, and C_GS, C_GD, and C_DB have only two independent capacitor voltages. The answer shows some general understanding that poles relate to energy storage, but incorrectly treats all four capacitors as independent.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 6251,
        "total_tokens": 7850,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5895,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 6251,
        "total_tokens": 7850,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5895,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this common-source MOSFET amplifier circuit, I need to identify the number of independent energy storage elements to determine the number of poles.\n\n## Identifying the Capacitors\n\nThe circuit shows four capacitors:\n- **C_GS**: Gate-to-source capacitance\n- **C_GD**: Gate-to-drain capacitance (Miller capacitance)\n- **C_DB**: Drain-to-bulk capacitance  \n- **C_SB**: Source-to-bulk capacitance\n\n## Analyzing the Circuit Topology\n\nThe key observation is that **the source terminal is directly connected to ground**. This is a crucial detail because:\n\n- C_SB is connected between source and ground (bulk)\n- Since the source is directly grounded, both terminals of C_SB are at the same potential\n- Therefore, C_SB has zero voltage across it and doesn't contribute to the circuit dynamics\n- C_SB does **not** create an independent pole\n\n## Counting Independent Nodes\n\nFor AC small-signal analysis, the circuit has **two independent nodes** (excluding ground):\n\n1. **Gate node**: Connected to C_GS (to ground) and C_GD (to drain)\n2. **Drain/Output node**: Connected to C_GD (to gate) and C_DB (to ground)\n\nThe three active capacitors (C_GS, C_GD, C_DB) are distributed across these 2 independent nodes.\n\n## Number of Poles\n\nThe number of poles equals the number of independent state variables in the circuit, which equals the number of independent nodes with capacitive elements:\n\n**Number of poles = 2**\n\nThese two poles are:\n1. **Input pole**: Formed by R_S and the input capacitance (C_GS plus Miller-multiplied C_GD)\n2. **Output pole**: Formed by R_D (and transistor output resistance) and the output capacitance (C_DB plus C_GD)\n\n**Answer: 2 poles**",
        "format": "markdown",
        "sha256": "fb3623b79befb0a02f48e9f759db56561f54ff9567ca40e8ccbbbf3c591fb8dc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes there are two poles and notes that C_SB is shorted out because both terminals are grounded, so it stores no energy. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5765,
        "total_tokens": 7364,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5297,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5765,
        "total_tokens": 7364,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5297,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this common-source MOSFET amplifier circuit, I need to count the number of independent energy storage elements (capacitors) to determine the number of poles.\n\n## Identifying the Capacitors\n\nThe circuit contains four capacitors:\n- **C_GS**: Gate-to-source capacitance\n- **C_GD**: Gate-to-drain (Miller) capacitance  \n- **C_DB**: Drain-to-body capacitance\n- **C_SB**: Source-to-body capacitance\n\n## Analysis\n\nHowever, I notice that:\n- The source of M₁ is **directly connected to ground**\n- The body is also at ground potential (standard for NMOS)\n- Therefore, **C_SB has zero voltage across it** in AC analysis and doesn't contribute to the dynamics\n\nThis leaves three active capacitors: C_GS, C_GD, and C_DB.\n\n## Determining Independent Energy Storage Elements\n\nFor the AC small-signal analysis, there are only **two independent nodes** (excluding ground):\n1. Gate node\n2. Drain node (output)\n\nThe three capacitors form a **capacitor-only loop**:\n- C_GS from gate to ground\n- C_DB from ground to drain\n- C_GD from drain back to gate\n\nWith 3 capacitors forming 1 capacitor-only loop:\n\n**Number of independent capacitors = 3 - 1 = 2**\n\nAlternatively, the capacitor voltages depend on only 2 node voltages:\n- V_CGS = V_gate\n- V_CGD = V_gate - V_drain  \n- V_CDB = V_drain\n\nThis creates a **2nd-order system**.\n\n## Answer\n\nThe circuit has **2 poles** - typically one associated with the input time constant (R_S with input capacitances) and one with the output time constant (R_D with output capacitances).",
        "format": "markdown",
        "sha256": "d90c19954da5827202a94318fa94dd54341e6ee2ce3bbd1d58c3d66dc640cce4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the count by noting that C_SB is shorted out and the other three capacitor voltages have only two independent values.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 6698,
        "total_tokens": 8297,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6246,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 6698,
        "total_tokens": 8297,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6246,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## **Circuit Type**\nThis is a **common-source MOSFET amplifier with voltage-series (shunt-series) feedback**.\n\n## **Circuit Components & Topology**\n- **M1**: N-channel MOS transistor (common-source configuration)\n- **RD**: Drain load resistor  \n- **R1, R2**: Feedback resistor network\n- **Input**: Gate terminal (Vin)\n- **Output**: Drain terminal (Vout)\n\n## **Operating Principle**\n\n### DC Biasing:\n- M1 must operate in saturation region for amplification\n- DC current path: VDD → RD → M1 (drain-to-source) → R2 → Ground\n- R1 provides DC feedback from output to source\n- VF = Vout × [R2/(R1+R2)] (voltage divider)\n\n### AC Operation:\n1. **Signal flow**: Input signal at gate modulates VGS\n2. **Amplification**: Change in VGS causes proportional change in drain current\n3. **Inversion**: Vout = VDD - ID·RD (inverting gain)\n4. **Feedback**: Portion of Vout feeds back to source through R1-R2 network\n\n## **Feedback Analysis**\n\n**Feedback Factor**: β = R2/(R1 + R2)\n\n**Feedback Signal**: VF = β · Vout\n\n**Gate-Source Voltage**: VGS = Vin - VF = Vin - β·Vout\n\n### Type of Feedback:\n- **Negative feedback** (series-shunt topology)\n- Output voltage sampled by R1-R2\n- Fed back in series with input at source terminal\n\n## **Small-Signal Voltage Gain**\n\nWithout detailed calculations, the approximate closed-loop gain:\n\n$$A_v = \\frac{v_{out}}{v_{in}} = \\frac{-g_m R_D}{1 + g_m R_D \\beta}$$\n\nWhere:\n- gm = transconductance of M1\n- β = R2/(R1+R2)\n\n## **Advantages of This Configuration**\n\n1. **Gain stabilization** - less dependent on transistor parameters\n2. **Increased linearity** - negative feedback reduces distortion\n3. **Wider bandwidth** - feedback extends frequency response\n4. **Better impedance characteristics**\n\n## **Key Characteristics**\n\n| Parameter | Effect |\n|-----------|--------|\n| **Gain** | Reduced but stable (compared to no feedback) |\n| **Input Impedance** | Very high (gate terminal) |\n| **Output Impedance** | Reduced by feedback |\n| **Bandwidth** | Increased by factor (1 + T) |\n| **Distortion** | Reduced by factor (1 + T) |\n\nWhere T = loop gain = gm·RD·β\n\nThis configuration is commonly used when stable, predictable gain with good linearity is required.",
        "format": "markdown",
        "sha256": "1bdb7efe2ea6fb75446c7b85abeeaf3c2724acfe249b478169032f9891f6a352"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes the divider factor and negative feedback, but swaps the terminals: the input is at the source and the divider feeds the gate. That topology error leads to an incorrect inverting gain instead of the circuit’s non-inverting closed-loop gain.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 5947,
        "total_tokens": 7543,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 5947,
        "total_tokens": 7543,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Feedback\n\n## Circuit Type\nThis is a **common-source MOSFET amplifier with shunt-series (voltage-voltage) negative feedback**.\n\n## Circuit Components and Connections\n\n- **M1**: NMOS transistor (common-source configuration)\n  - Gate: Input (Vin)\n  - Drain: Output (Vout) \n  - Source: Feedback node (VF)\n\n- **RD**: Drain load resistor (VDD to drain)\n- **R1**: Feedback resistor (Vout to VF)\n- **R2**: Source resistor (VF to ground)\n\n## Key Features\n\n### Topology\nThe circuit has a **feedback path** from the output (drain) back to the source through R1, with R2 providing the source-to-ground connection. This creates a voltage divider at the source node.\n\n### DC Biasing\n- VDD supplies power through RD\n- The gate voltage Vin sets the operating point\n- Source voltage VF = ID(R1||R2) approximately, where ID is the drain current\n- Current flows: VDD → RD → M1 → (R1||R2) → Ground\n\n### Small-Signal Characteristics\n\n**Voltage Gain:**\n- Less than standard common-source due to negative feedback\n- Approximately: **Av ≈ -gm·RD/(1 + gm·R2 + RD/R1)**\n- Inverted output (180° phase shift)\n\n**Input Impedance:**\n- Very high (gate of MOSFET)\n\n**Output Impedance:**\n- Reduced by feedback, approximately **Rout ≈ RD/(1 + loop gain)**\n\n## Advantages of This Configuration\n\n1. **Stable gain** - less dependent on transistor parameters\n2. **Improved linearity** - negative feedback reduces distortion\n3. **Extended bandwidth** - feedback trades gain for bandwidth\n4. **Better bias stability** - R2 provides DC stabilization\n5. **Predictable performance** - gain depends more on resistor ratios\n\n## Applications\n- Linear amplifier stages\n- Signal conditioning\n- Analog preprocessing\n- Applications requiring stable, predictable gain with good linearity\n\nThis is a practical amplifier design that sacrifices some gain for improved overall performance characteristics.",
        "format": "markdown",
        "sha256": "d5a4cfa045985d9fbaf942116063895937f653b3aeda3e93c5616885a819534f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer reverses the essential connections: Vin is applied at M1’s source, while the output divider feeds the gate. Its common-source topology and inverting gain are therefore wrong, though it recognizes that the circuit uses resistive feedback.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 3103,
        "total_tokens": 4699,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2556,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 3103,
        "total_tokens": 4699,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2556,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Feedback\n\n## Circuit Configuration\n\nThis is a **common-source MOSFET amplifier with voltage-divider feedback** (also called shunt-series feedback). The key feature is that the source terminal is connected to a voltage divider (R₁-R₂) that samples the output voltage.\n\n## Circuit Topology\n\n- **Input**: Applied to gate (Vin)\n- **Output**: Taken from drain (Vout)  \n- **Load**: RD (drain resistor)\n- **Feedback**: R₁-R₂ voltage divider feeds back from Vout to source (VF)\n\n## DC Operating Point\n\nThe DC bias is established through the feedback network:\n\n- **Source voltage**: VF = Vout × R₂/(R₁+R₂)\n- **Gate-source voltage**: VGS = Vin - VF\n- **Output voltage**: Vout = VDD - ID·RD\n\nThe negative feedback stabilizes the Q-point against transistor parameter variations.\n\n## AC Small-Signal Analysis\n\n### Voltage Gain\n\nFor the AC analysis:\n- vgs = vin - vf = vin - vout · R₂/(R₁+R₂)\n- id = gm · vgs  \n- vout = -id · RD = -gm · RD · vgs\n\nSolving for the voltage gain:\n\n$$A_v = \\frac{v_{out}}{v_{in}} = \\frac{-g_m R_D}{1 + g_m R_D \\cdot \\frac{R_2}{R_1+R_2}}$$\n\nFor high open-loop gain (gm·RD >> 1):\n\n$$A_v \\approx -\\frac{R_1+R_2}{R_2} = -\\left(1 + \\frac{R_1}{R_2}\\right)$$\n\n**The gain becomes primarily determined by the resistor ratio**, similar to op-amp circuits.\n\n## Key Characteristics\n\n### Advantages:\n✓ **Stable bias point** - self-regulating through feedback  \n✓ **Reduced gain sensitivity** - less dependent on gm variations  \n✓ **Improved linearity** - negative feedback reduces distortion  \n✓ **Predictable gain** - set by passive components (R₁/R₂)\n\n### Disadvantages:\n✗ **Reduced gain** - compared to a simple common-source stage  \n✗ **Loading effects** - R₁, R₂ affect input/output impedance\n\n## Applications\n\nThis configuration is useful when:\n- Stable, predictable gain is required\n- Component variations must be tolerated\n- Moderate gain with good linearity is needed\n- DC bias stability is important",
        "format": "markdown",
        "sha256": "9491b9efc8933feef85337c46f7c2648b5a3c455d2695061599b4d79e1954957"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer reverses the essential connections: the input is at the source and the output divider feeds the gate, not vice versa. It therefore analyzes the wrong topology and gives an inverting gain instead of the actual non-inverting feedback gain.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 2504,
        "total_tokens": 4100,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1842,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1596,
        "output_tokens": 2504,
        "total_tokens": 4100,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1842,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Source Follower with Active Load\n\n## Circuit Configuration\n\nThis is a **source follower (common-drain) amplifier** with an **NMOS current source load**. Both M1 and M2 are NMOS transistors.\n\n## Component Identification\n\n- **M1 (Top transistor):**\n  - Gate: Vin (input)\n  - Drain: VDD (power supply)\n  - Source: Vout (output)\n  \n- **M2 (Bottom transistor):**\n  - Gate: Vb (bias voltage)\n  - Drain: Vout \n  - Source: Ground\n  - Functions as an active current source\n\n## Circuit Operation\n\n### DC Operation\n- Vout follows Vin with an offset: **Vout ≈ Vin - VGS1**\n- M2 sets the bias current based on Vb\n- Both transistors carry the same DC current (series connection)\n\n### AC Operation\n- When Vin increases, Vout increases proportionally\n- **No phase inversion** occurs (unlike common-source amplifiers)\n- The output \"follows\" the input\n\n## Key Characteristics\n\n| Parameter | Value/Description |\n|-----------|------------------|\n| **Voltage Gain** | Av < 1 (typically 0.7-0.95) |\n| **Input Impedance** | Very high (gate input) |\n| **Output Impedance** | Low: ~1/(gm1 + gmb1) |\n| **Phase Shift** | 0° (no inversion) |\n\n### Voltage Gain Formula\n$$A_v = \\frac{g_{m1}}{g_{m1} + g_{mb1} + g_{ds1} + g_{m2} + g_{ds2}} < 1$$\n\n## Applications\n\n1. **Buffer stage** - isolates one circuit from another\n2. **Impedance matching** - converts high impedance to low impedance\n3. **Level shifting** - shifts DC voltage levels\n4. **Output driver** - drives capacitive loads\n\n## Advantages\n- High input impedance\n- Low output impedance  \n- Wide bandwidth\n- Good linearity\n\n## Disadvantages\n- Voltage gain less than unity\n- Consumes DC power continuously\n- Limited voltage swing",
        "format": "markdown",
        "sha256": "36e5469a17506546d785ac61b1cbefe90c8efa78cf02a195603aae4f80ae5e09"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower, M2 as its NMOS current-source load, and the positive, below-unity gain, satisfying the golden full-credit rule. The detailed gain expression is imperfect because it includes gm2, but the main conclusion is correct.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 1522,
        "total_tokens": 2841,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 978,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 1522,
        "total_tokens": 2841,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 978,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Source Follower with Active Load\n\n## Circuit Identification\nThis is a **source follower (common-drain amplifier)** with an **NMOS active load**.\n\n## Circuit Components\n- **M1**: NMOS transistor configured as source follower\n  - Gate: V_in (input)\n  - Drain: V_DD (supply)\n  - Source: V_out (output)\n\n- **M2**: NMOS transistor acting as current source\n  - Gate: V_b (bias voltage)\n  - Drain: V_out\n  - Source: Ground\n\n## Operating Principle\n\n### DC Operation\n1. **M2** functions as a current source, with current determined by bias voltage V_b\n2. **M1** operates as a follower: V_out ≈ V_in - V_GS1\n3. The output \"follows\" the input with a DC level shift of approximately one threshold voltage\n\n### Bias Conditions\nFor proper operation (both transistors in saturation):\n- **M1**: V_DD - V_out ≥ V_in - V_out - V_th1 → V_DD ≥ V_in\n- **M2**: V_out ≥ V_b - V_th2\n\n## Small-Signal Characteristics\n\n**Voltage Gain:**\n$$A_v = \\frac{g_{m1}}{g_{m1} + g_{mb1} + g_{ds1} + g_{ds2}} \\approx 1$$\n\n**Output Impedance:**\n$$R_{out} \\approx \\frac{1}{g_{m1} + g_{mb1}}$$ (typically 100Ω - 1kΩ)\n\n## Key Features\n\n### Advantages\n✓ High input impedance  \n✓ Low output impedance  \n✓ Wide bandwidth  \n✓ Good linearity  \n✓ Excellent buffer characteristics\n\n### Disadvantages\n✗ Voltage gain < 1  \n✗ DC level shift (V_out < V_in)  \n✗ Limited output swing\n\n## Applications\n- **Buffer stages** between high and low impedance sections\n- **Impedance matching**\n- **Output drivers**\n- **Level shifting circuits**",
        "format": "markdown",
        "sha256": "536210db3329464b00e59f4d6bec0a2e7e4a5e9f677df457f033102f2b0c5880"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its NMOS current-source load, with a positive gain slightly below unity. The simplified gain and output-resistance expressions omit some finite-output-resistance detail, but the golden solution explicitly allows full credit for this core answer.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 1404,
        "total_tokens": 2723,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 866,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 1404,
        "total_tokens": 2723,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 866,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Source Follower with Active Load\n\n## Circuit Configuration\n\nThis circuit consists of two NMOS transistors:\n- **M1**: Connected as a source follower (common-drain configuration)\n  - Drain → VDD\n  - Gate → Vin\n  - Source → Vout\n- **M2**: Acts as an active load/current source\n  - Drain → Vout\n  - Gate → Vb (bias voltage)\n  - Source → Ground\n\n## Circuit Type\n**Source Follower (Common-Drain Amplifier) with Active Load**\n\n## DC Analysis\n\nThe bias current is set by M2:\n$$I_D = \\frac{1}{2}\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2(V_b - V_{TH})^2$$\n\nAt equilibrium, the same current flows through M1:\n$$V_{out} = V_{in} - V_{GS1}$$\n\nwhere VGS1 depends on the required drain current.\n\n## Small-Signal Analysis\n\n**Voltage Gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_{m1}}{g_{m1} + g_{m2} + g_{ds1} + g_{ds2}}$$\n\nIf channel-length modulation is neglected (gds ≈ 0):\n$$A_v \\approx \\frac{g_{m1}}{g_{m1} + g_{m2}}$$\n\nTypically: **0.7 < Av < 0.95**\n\n**Output Impedance:**\n$$Z_{out} \\approx \\frac{1}{g_{m1} + g_{m2}}$$\n\n## Key Characteristics\n\n✓ **High input impedance** (gate of M1)  \n✓ **Low output impedance** (~1/gm)  \n✓ **Non-inverting** (output follows input)  \n✓ **Voltage gain < 1** (buffer)  \n✓ **Wide bandwidth**  \n\n## Operating Conditions\n\nFor proper operation:\n- **M1 in saturation**: Vin ≤ VDD + VTH\n- **M2 in saturation**: Vout ≥ Vb - VTH\n\n## Applications\n\n- **Buffer/impedance matching**\n- **Output driver stages**\n- **Level shifting circuits**\n- **Interfacing between stages**",
        "format": "markdown",
        "sha256": "33e3b6db57df27d6b964aeb06dcd43611cc78e46e392247d3908e256eb99da1b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly identifies M1 as a source follower, M2 as the current-source load, and the gain as positive and below unity, meeting the golden solution’s explicit full-credit rule.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 2170,
        "total_tokens": 3489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1583,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1319,
        "output_tokens": 2170,
        "total_tokens": 3489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1583,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Identification\nThis is a **CMOS (Complementary Metal-Oxide-Semiconductor) Inverter**, the fundamental building block of digital logic circuits.\n\n## Circuit Components\n- **M₂**: PMOS transistor (pull-up network, connected to V_DD)\n- **M₁**: NMOS transistor (pull-down network, connected to ground)\n- **Input**: V_in connected to both transistor gates\n- **Output**: V_out taken from the drain connection point\n\n## Operation\n\n### When V_in = LOW (≈ 0V):\n- **M₁ (NMOS)**: OFF (V_GS < V_th)\n- **M₂ (PMOS)**: ON (|V_GS| > |V_th|)\n- **Result**: V_out = V_DD (HIGH)\n\n### When V_in = HIGH (≈ V_DD):\n- **M₁ (NMOS)**: ON (V_GS > V_th)\n- **M₂ (PMOS)**: OFF (V_GS ≈ 0)\n- **Result**: V_out ≈ 0V (LOW)\n\n## Truth Table\n| V_in | V_out |\n|------|-------|\n| 0    | 1     |\n| 1    | 0     |\n\n## Key Characteristics\n\n✓ **Function**: Logic inverter (NOT gate)  \n✓ **Static Power**: Near zero (no DC path in steady state)  \n✓ **Output Swing**: Full rail-to-rail (0 to V_DD)  \n✓ **Switching**: Complementary - only one transistor ON at a time  \n✓ **Applications**: Digital logic, buffers, oscillators, logic gates\n\nThis configuration forms the basis of all CMOS logic families.",
        "format": "markdown",
        "sha256": "286e86a8d7b6fb47e9fb5845dae8e31096d27258af3d39bb0e8d5e6d98ec3be4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the CMOS inverter, device roles, and logic-level operation. However, both transistors can conduct during switching, so the claim that only one is on at a time is inaccurate.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 981,
        "total_tokens": 1329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 524,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 981,
        "total_tokens": 1329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 524,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Type\nThis is a **CMOS (Complementary Metal-Oxide-Semiconductor) Inverter**, the most fundamental building block in digital electronics.\n\n## Circuit Components\n\n- **M₂** (top): PMOS transistor connected between V_DD and V_out\n- **M₁** (bottom): NMOS transistor connected between V_out and ground\n- Both gates are connected together to V_in\n- Both drains are connected together to V_out\n\n## Operation\n\n### When V_in = LOW (≈ 0V):\n- **M₁ (NMOS)**: OFF (V_GS ≈ 0V, below threshold)\n- **M₂ (PMOS)**: ON (V_SG = V_DD, above threshold)\n- **V_out**: Pulled HIGH to **V_DD**\n\n### When V_in = HIGH (≈ V_DD):\n- **M₁ (NMOS)**: ON (V_GS = V_DD, above threshold)\n- **M₂ (PMOS)**: OFF (V_SG ≈ 0V, below threshold)\n- **V_out**: Pulled LOW to **Ground**\n\n## Truth Table\n| V_in | V_out |\n|------|-------|\n| 0    | 1     |\n| 1    | 0     |\n\n## Key Characteristics\n\n✓ **Logic Function**: NOT gate (inverter)  \n✓ **Power Consumption**: Very low static power (no DC path in steady state)  \n✓ **Output Swing**: Full rail-to-rail (0V to V_DD)  \n✓ **Noise Margins**: Excellent  \n✓ **Switching**: Only one transistor conducts at a time\n\n## Applications\n- Digital logic circuits\n- Signal buffering and level shifting\n- Oscillators and ring oscillators\n- Foundation for complex gates (NAND, NOR, XOR, etc.)",
        "format": "markdown",
        "sha256": "958e56fbe52ec11f2aaa7ada950f444b2e88ada74cd300fdce86b62001c3f17f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the CMOS inverter and its pull-up/pull-down operation, but incorrectly says only one transistor conducts during switching; both may conduct briefly during a transition.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1023,
        "total_tokens": 1371,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 540,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1023,
        "total_tokens": 1371,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 540,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Identification\nThis is a **CMOS (Complementary Metal-Oxide-Semiconductor) Inverter**, the most fundamental building block in digital electronics.\n\n## Circuit Components\n- **M₂** (top): PMOS transistor connected between V_DD and V_out\n- **M₁** (bottom): NMOS transistor connected between V_out and ground\n- Both gates connected to V_in\n- Output taken from the common drain connection\n\n## Operating Principle\n\n### When V_in = LOW (Logic 0)\n- **M₁ (NMOS)**: OFF - no current path to ground\n- **M₂ (PMOS)**: ON - creates path from V_DD to output\n- **Result**: V_out = HIGH (V_DD) ✓\n\n### When V_in = HIGH (Logic 1)\n- **M₁ (NMOS)**: ON - creates path to ground\n- **M₂ (PMOS)**: OFF - no current path from V_DD\n- **Result**: V_out = LOW (0V) ✓\n\n## Truth Table\n| V_in | V_out |\n|------|-------|\n| 0    | 1     |\n| 1    | 0     |\n\n## Key Characteristics\n\n**Advantages:**\n- ⚡ **Low static power** - only one transistor conducts at steady state\n- 🎯 **Full voltage swing** - output swings from 0V to V_DD\n- 🛡️ **High noise immunity** - rail-to-rail operation\n- 🔄 **Complementary operation** - no DC path from V_DD to ground\n\n**Applications:**\n- Digital logic gates\n- Microprocessors\n- Memory circuits\n- All modern CMOS integrated circuits\n\nThis inverter forms the basis for NAND, NOR, and other complex logic gates in digital design.",
        "format": "markdown",
        "sha256": "e87997b1092ffc219367ba246e8b1f5872f367cce0fb0ce8c1aa6cbd52f30388"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter and the NMOS pull-down/PMOS pull-up roles, including the correct input-output behavior. Extra analog analysis is not required.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1141,
        "total_tokens": 1489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 680,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1141,
        "total_tokens": 1489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 680,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Description\nThis is a **CMOS (Complementary Metal-Oxide-Semiconductor) Inverter**, one of the most fundamental digital logic gates.\n\n## Circuit Components\n- **M₁**: PMOS transistor (connected to V_DD)\n- **M₂**: NMOS transistor (connected to ground)\n- **Input**: V_in (common gate connection)\n- **Output**: V_out (common drain connection)\n\n## Operation Analysis\n\n### When V_in = LOW (Logic 0)\n- **M₁ (PMOS)**: V_GS is negative → **ON** (conducting)\n- **M₂ (NMOS)**: V_GS ≈ 0V → **OFF** (non-conducting)\n- **Result**: V_out = V_DD (**HIGH/Logic 1**)\n\n### When V_in = HIGH (Logic 1)\n- **M₁ (PMOS)**: V_GS ≈ 0V → **OFF** (non-conducting)\n- **M₂ (NMOS)**: V_GS is positive → **ON** (conducting)\n- **Result**: V_out = 0V (**LOW/Logic 0**)\n\n## Truth Table\n| V_in | V_out |\n|------|-------|\n| 0    | 1     |\n| 1    | 0     |\n\n## Key Characteristics\n\n✓ **Function**: NOT gate (Logic Inverter)\n\n✓ **Low static power**: No DC path from V_DD to ground in steady state\n\n✓ **High noise immunity**: Strong output drive in both states\n\n✓ **Rail-to-rail output**: Full voltage swing (0 to V_DD)\n\n✓ **Complementary operation**: Only one transistor conducts at a time\n\n## Applications\n- Fundamental building block in all digital CMOS circuits\n- Signal inversion and buffering\n- Clock signal generation and distribution\n- Used in complex logic gates, flip-flops, and memories",
        "format": "markdown",
        "sha256": "2a7dab748a28bae2a277429c6f3f2e6baaefcb2e0f8a007cb12e7d7c5ae22c69"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as PMOS and analyzes the circuit as an ordinary complementary CMOS inverter; the figure has two NMOS devices.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1095,
        "total_tokens": 1443,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 604,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1095,
        "total_tokens": 1443,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 604,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Overview\nThis is a **CMOS (Complementary Metal-Oxide-Semiconductor) Inverter**, also known as a NOT gate. It consists of:\n- **M₁**: PMOS transistor (pull-up network)\n- **M₂**: NMOS transistor (pull-down network)\n- Both gates connected to the input (Vin)\n- Output (Vout) taken from the common drain connection\n\n## Operation\n\n### When Vin = LOW (≈ 0V):\n- **M₁ (PMOS)**: VGS is negative → **ON** (conducts)\n- **M₂ (NMOS)**: VGS ≈ 0V → **OFF** (non-conducting)\n- **Vout = HIGH (≈ VDD)** - pulled up through M₁\n\n### When Vin = HIGH (≈ VDD):\n- **M₁ (PMOS)**: VGS ≈ 0V → **OFF** (non-conducting)\n- **M₂ (NMOS)**: VGS is positive → **ON** (conducts)\n- **Vout = LOW (≈ 0V)** - pulled down through M₂\n\n## Truth Table\n| Vin | Vout |\n|-----|------|\n| 0   | 1    |\n| 1   | 0    |\n\n## Key Characteristics\n\n✓ **Complementary operation** - only one transistor conducts at a time\n\n✓ **Near-zero static power consumption** - no DC path from VDD to ground\n\n✓ **Rail-to-rail output swing** - full voltage range (0 to VDD)\n\n✓ **High noise immunity** - characteristic of CMOS logic\n\n✓ **Fundamental building block** - basis for complex digital circuits\n\n## Applications\n- Digital logic gates\n- Signal inversion and buffering\n- Clock generation circuits\n- Interface circuits",
        "format": "markdown",
        "sha256": "c27ae365322dfa7bab174a433f52361ecc04891be1049d9ee384aab1d29ee8a9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as PMOS and analyzes the circuit as an ordinary CMOS inverter. Both devices are NMOS, so this violates the golden solution’s non-negotiable scoring rule.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1140,
        "total_tokens": 1488,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 660,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1140,
        "total_tokens": 1488,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 660,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# CMOS Inverter Circuit Analysis\n\n## Circuit Identification\nThis is a **CMOS Inverter** (NOT gate), one of the most fundamental digital logic circuits.\n\n## Circuit Configuration\n\n**Components:**\n- **M₁**: PMOS transistor (pull-up network)\n  - Source connected to V_DD\n  - Gate connected to V_in\n  - Drain connected to V_out\n\n- **M₂**: NMOS transistor (pull-down network)\n  - Source connected to ground\n  - Gate connected to V_in\n  - Drain connected to V_out\n\n## Operation Analysis\n\n### When V_in = LOW (≈ 0V):\n- **M₁ (PMOS):** V_GS = -V_DD → **ON** (conducting)\n- **M₂ (NMOS):** V_GS = 0V → **OFF** (non-conducting)\n- **Result:** V_out = V_DD (**HIGH**)\n\n### When V_in = HIGH (≈ V_DD):\n- **M₁ (PMOS):** V_GS = 0V → **OFF** (non-conducting)\n- **M₂ (NMOS):** V_GS = V_DD → **ON** (conducting)\n- **Result:** V_out ≈ 0V (**LOW**)\n\n## Truth Table\n| V_in | V_out |\n|------|-------|\n| 0    | 1     |\n| 1    | 0     |\n\n## Key Characteristics\n\n✓ **Low static power** - No direct path from V_DD to ground in steady state  \n✓ **Rail-to-rail output** - Full voltage swing (0 to V_DD)  \n✓ **High noise immunity** - Strong pull-up and pull-down  \n✓ **Complementary operation** - Only one transistor conducts at a time  \n✓ **Scalable** - Foundation for all CMOS logic gates\n\nThis is the basic building block of modern digital integrated circuits.",
        "format": "markdown",
        "sha256": "e1b89e248f8d7f8f88153537e2be0c3c36c1f5d765701320595b043c1ee7ac02"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the upper transistor as PMOS and analyzes the circuit as an ordinary complementary CMOS inverter. The golden solution requires recognizing both devices as NMOS, so this receives 0.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1052,
        "total_tokens": 1400,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 348,
        "output_tokens": 1052,
        "total_tokens": 1400,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Diode-Connected Load\n\n## Circuit Configuration\n\nThis is a **common-source amplifier with an active (diode-connected) PMOS load**. The key features are:\n\n- **M1 (NMOS)**: Input transistor with gate connected to V_in, source grounded\n- **M2 (PMOS)**: Diode-connected load (gate and drain shorted together) with source at V_DD\n- **Output**: Taken from the common drain connection\n\n## Operating Principles\n\n### DC Operation\n\n**When V_in is LOW:**\n- M1 is OFF or in weak inversion\n- M2 pulls V_out toward V_DD\n- V_out ≈ V_DD - |V_TP| (one threshold voltage below supply)\n\n**When V_in is HIGH:**\n- M1 is strongly ON\n- Both transistors conduct current simultaneously\n- V_out drops to a low value determined by the current division\n\n### Transfer Characteristic\n\nThe voltage transfer curve shows:\n- **Non-rail-to-rail output**: V_out(max) ≈ V_DD - |V_TP|\n- **Inversion**: Output decreases as input increases\n- **Transition region**: Determined by transistor sizing ratio\n\n## Key Characteristics\n\n**Advantages:**\n- Simple design (2 transistors)\n- Good voltage gain in analog applications\n- Faster than resistive loads\n\n**Disadvantages:**\n- ⚡ **Static power dissipation** when V_in is high\n- Reduced output voltage swing\n- Not full rail-to-rail operation\n\n## Applications\n\n- **Analog circuits**: Amplifier stage, active load\n- **Digital circuits**: Pseudo-NMOS logic (when low power isn't critical)\n- **Level shifting circuits**",
        "format": "markdown",
        "sha256": "d0b64a32973770fcc3eaf7ef47c65d9e93c9cd7ca7baa1e0c5b30c357786a5ce"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the common-source NMOS stage, diode-connected PMOS load, and inversion, but omits the central small-signal gain result (approximately −gm1/gm2).",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1658,
        "total_tokens": 2474,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1228,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1658,
        "total_tokens": 2474,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1228,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Diode-Connected Load\n\n## Circuit Configuration\n\nThis is a **common-source amplifier with an active (diode-connected) PMOS load**:\n\n- **M1**: NMOS transistor (input/amplifying device)\n  - Gate: Connected to input signal (Vin)\n  - Source: Grounded\n  - Drain: Connected to output (Vout)\n\n- **M2**: PMOS transistor (active load)\n  - Gate and Drain: Connected together (diode-connected)\n  - Source: Connected to VDD\n  - Configuration makes it always operate in saturation\n\n## Circuit Function\n\nThis is a **single-stage amplifier** commonly used in analog CMOS circuits.\n\n### Key Characteristics:\n\n1. **Voltage Gain**: \n   - Provides moderate voltage gain\n   - Av ≈ -gm1/(gm2 + gds1 + gds2)\n   - Simplified: Av ≈ -gm1/gm2 (when output resistances are large)\n   - Typical gain magnitude: 5-20 (depending on transistor sizing)\n\n2. **Phase**: 180° phase shift (inverting amplifier)\n\n3. **DC Operating Point**:\n   - Set by the equilibrium where ID1 = ID2\n   - M2's diode connection provides automatic biasing\n\n4. **Output Resistance**:\n   - Rout = ro1 || (1/gm2 + ro2) ≈ ro1 || 1/gm2\n\n### Advantages:\n- Simple biasing (self-biased through M2)\n- Compact layout\n- Good power supply rejection\n- No external resistors needed\n\n### Applications:\n- Analog amplifier stages\n- Op-amp input stages\n- Sensor interface circuits\n- First stage in multi-stage amplifiers",
        "format": "markdown",
        "sha256": "f4746c4e596d45421e352c9fa3c34c85152f8dd251224705eb1318639bc67bca"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain with channel-length modulation treated consistently. The separate output-resistance expression is inaccurate, but does not affect the required full-credit criteria.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1327,
        "total_tokens": 2143,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 875,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1327,
        "total_tokens": 2143,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 875,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common Source Amplifier with Active Load\n\n## Circuit Configuration\n\nThis is a **common source amplifier with a diode-connected PMOS load**. The circuit consists of:\n\n- **M₁**: NMOS transistor (input/amplifying device)\n  - Gate: Connected to Vᵢₙ\n  - Source: Connected to ground\n  - Drain: Connected to Vₒᵤₜ\n\n- **M₂**: PMOS transistor (active load)\n  - Gate: Connected to its own drain (diode-connected)\n  - Source: Connected to V_DD\n  - Drain: Connected to Vₒᵤₜ\n\n## Operating Principle\n\n### DC Operation\n\n1. **M₂ as Active Load**: With gate tied to drain, M₂ operates as a diode-connected transistor, functioning as an active current source load\n   - Always in saturation region\n   - Provides high impedance load for M₁\n\n2. **Bias Point**: Determined by the intersection of M₁ and M₂ characteristics where I_D1 = I_D2\n\n3. **Output States**:\n   - **Vᵢₙ low**: M₁ OFF → Vₒᵤₜ ≈ V_DD - |V_TP|\n   - **Vᵢₙ high**: M₁ ON → Vₒᵤₜ decreases\n\n### AC Small-Signal Analysis\n\n**Voltage Gain**: \n$$A_v = -g_{m1}(r_{o1} \\parallel r_{o2})$$\n\nWhere:\n- g_m1 = transconductance of M₁\n- r_o1, r_o2 = output resistances\n- Negative sign indicates **inverting** amplifier\n\n**Output Impedance**: R_out = r_o1 || r_o2 (relatively high)\n\n## Key Characteristics\n\n✓ **Advantages**:\n- Simple 2-transistor design\n- Moderate voltage gain\n- Compact layout\n- Good for analog signal amplification\n\n✗ **Disadvantages**:\n- Continuous DC power consumption\n- Limited voltage swing\n- Moderate gain compared to other configurations\n\n## Applications\n\n- Analog amplifier stages in op-amps\n- Signal conditioning circuits\n- Input stages of analog circuits\n- Low-to-moderate gain amplification",
        "format": "markdown",
        "sha256": "cdf451fe0cdd6d61395270415f7cac266789fd0c033a5debac57d054452dd596"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the common-source NMOS stage, diode-connected PMOS load, and inverting action, but its gain omits the diode-connected PMOS’s dominant small-signal conductance gm2. The load is approximately 1/gm2 || ro2, not ro2 alone, so the stated gain and output impedance are materially wrong.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1689,
        "total_tokens": 2505,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1110,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 816,
        "output_tokens": 1689,
        "total_tokens": 2505,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1110,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Configuration\n\nThis is a **common-source amplifier with a diode-connected load**, consisting of:\n\n- **M₂**: PMOS transistor (input device)\n  - Source → V_DD\n  - Gate → V_in\n  - Drain → V_out\n\n- **M₁**: NMOS transistor (active load)\n  - Drain and Gate tied together → V_out (diode-connected)\n  - Source → Ground\n\n## Circuit Function\n\nThis is an **inverting amplifier** that provides voltage gain.\n\n### DC Operating Point\n\n1. M₁ operates as a diode-connected device where V_GS1 = V_DS1\n2. Both transistors carry the same drain current: I_D1 = I_D2\n3. The output voltage adjusts to satisfy this current equality\n4. M₁ remains in saturation (guaranteed by diode connection)\n\n### Transfer Characteristics\n\n- **V_in LOW** → M₂ strongly ON → V_out pulled HIGH (toward V_DD)\n- **V_in HIGH** → M₂ weak/OFF → V_out pulled LOW\n- **Result**: Inverted output signal\n\n## Small-Signal Performance\n\n**Voltage Gain:**\n$$A_v \\approx -g_{m2} \\cdot (r_{o2} \\parallel r_{o1}) \\approx -\\frac{g_{m2}}{g_{m1}}$$\n\nWhere the diode-connected M₁ has effective resistance ≈ 1/g_m1\n\n## Key Features\n\n✓ **Advantages:**\n- Simple, compact design\n- Provides moderate voltage gain\n- Self-biasing due to diode load\n- M₂ stays in saturation over good input range\n\n✗ **Limitations:**\n- Non-linear transfer characteristic\n- Limited output voltage swing\n- Moderate gain compared to other topologies\n\n## Applications\n\n- Analog gain stages\n- Operational amplifier designs\n- Signal processing circuits\n- CMOS analog building blocks",
        "format": "markdown",
        "sha256": "65dd030b48c0e2a4cc9266b4ca541affefeec0e4dd0d0efa7c35ad75fa368254"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies an inverting common-source stage and gives the gm/gm gain, but misidentifies M1 and its connections: the actual load is a PMOS with gate and drain tied to ground, not an NMOS with gate and drain at Vout. That is a significant topology error.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1722,
        "total_tokens": 3310,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1722,
        "total_tokens": 3310,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Configuration\n\nThis is a **PMOS inverter with diode-connected NMOS load** circuit, consisting of:\n\n- **M₂** (PMOS): Input switching transistor\n  - Source → VDD\n  - Gate → Vin\n  - Drain → Vout\n  \n- **M₁** (NMOS): Diode-connected load transistor\n  - Gate and Drain → Vout (shorted together)\n  - Source → Ground\n\n## Operating Principles\n\n### When Vin = LOW (≈ 0V):\n- **M₂ ON**: VGS = -VDD (large negative voltage) → PMOS conducts strongly\n- **M₁ ON**: Acts as active load\n- **Vout = HIGH** (≈ VDD)\n- Current flows from VDD through both transistors to ground (static power dissipation)\n\n### When Vin = HIGH (≈ VDD):\n- **M₂ OFF**: VGS = 0 → PMOS is cut off\n- **M₁ ON**: Diode-connected configuration keeps it conducting\n- **Vout = LOW** (≈ Vₜₕ of M₁, typically 0.3-0.7V, **not** 0V)\n\n## Key Characteristics\n\n**Advantages:**\n- Simple design (only 2 transistors)\n- Inverting logic function\n- Compact layout\n\n**Disadvantages:**\n- ⚠️ **Static power consumption** when Vin is LOW\n- ⚠️ **Poor LOW output level** (≈ Vₜₕ, not rail-to-rail)\n- Asymmetric switching characteristics\n- Limited noise margin on LOW level\n\n## Application Context\n\nThis topology is characteristic of older **NMOS logic** or **pseudo-NMOS** design styles. Modern CMOS circuits typically use complementary push-pull configurations for better power efficiency and full rail-to-rail swing.",
        "format": "markdown",
        "sha256": "8794624932b0e1db699b40226c8b395c4cfc827638894d492b76f4ca83e5d7f0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies M1 as an NMOS with gate and drain at Vout; the actual circuit has two PMOS devices, with M1's gate and drain tied to ground. It therefore misses the diode-connected PMOS load and the central gm/gm gain analysis.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1502,
        "total_tokens": 3090,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1021,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1502,
        "total_tokens": 3090,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1021,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Configuration\n\nThis circuit consists of:\n- **M2 (PMOS)**: Source connected to VDD, gate connected to Vin, drain connected to Vout\n- **M1 (NMOS)**: Source connected to ground, gate connected to ground, drain connected to Vout\n\n## Key Observation\n\nThe critical feature is that **M1's gate is tied to ground** (VGS = 0V), which significantly affects circuit operation.\n\n## Analysis - Two Possibilities:\n\n### **Scenario 1: M1 is Enhancement-Mode NMOS**\n\nIf M1 is a standard enhancement-mode device:\n\n- **M1 is permanently OFF** (VGS = 0 < Vth)\n- **Operation:**\n  - **Vin = LOW (0V)**: M2 turns ON → Vout = HIGH (VDD)\n  - **Vin = HIGH (VDD)**: M2 turns OFF → Vout = **floating/high-Z**\n\nThis would be a **poor/incomplete circuit design** since Vout has no discharge path when Vin is high.\n\n### **Scenario 2: M1 is Depletion-Mode NMOS** ⭐\n\nIf M1 is a depletion-mode device (Vth < 0):\n\n- **M1 is always ON**, acting as a **passive load resistor**\n- **Operation:**\n  - **Vin = LOW**: M2 ON (strong) → Vout ≈ HIGH (VDD)\n  - **Vin = HIGH**: M2 OFF, current through M1 → Vout = LOW\n\nThis is a **depletion-load inverter** (pseudo-NMOS style with PMOS driver).\n\n## Circuit Characteristics\n\n- **Functionality**: Inverter (if M1 is depletion-mode)\n- **Power consumption**: Static power dissipation when Vin = HIGH\n- **Advantages**: Fewer transistors than CMOS\n- **Disadvantages**: Poor noise margins, static power consumption, asymmetric switching\n\n**Most likely interpretation**: This is a ratioed logic inverter with depletion-load configuration.",
        "format": "markdown",
        "sha256": "d4ff05cfa5a1b1bff04b7ba5b8a52b56e0bb476214f38deae0aee4b531375e9f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as an NMOS and concludes the output is floating or the circuit is a depletion-load inverter. In the actual circuit both devices are PMOS, and M1 is a diode-connected PMOS load, so the central topology and analysis are wrong.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 3037,
        "total_tokens": 4625,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2516,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 3037,
        "total_tokens": 4625,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2516,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, I can see a **cascode current source** configuration with two NMOS transistors M₁ and M₂ stacked in series.\n\n## Circuit Analysis\n\n**Configuration:**\n- M₁ (bottom): Common-source stage with gate voltage V_b1\n- M₂ (top): Common-gate (cascode) stage with gate voltage V_b2  \n- Output node: X (between M₁ and M₂)\n\n## Finding R_out\n\nThe output resistance of a cascode current source is measured at node X. Using small-signal analysis:\n\n**For the cascode configuration:**\n\nThe output resistance looking into node X is:\n\n$$R_{out} = r_{o1}(1 + g_{m2} \\cdot r_{o2}) + r_{o2}$$\n\nSince typically $g_{m2} \\cdot r_{o2} >> 1$, this simplifies to:\n\n$$\\boxed{R_{out} \\approx g_{m2} \\cdot r_{o1} \\cdot r_{o2}}$$\n\n**Where:**\n- $g_{m2}$ = transconductance of M₂\n- $r_{o1}$ = output resistance of M₁ = $\\frac{1}{\\lambda_1 I_{D}}$\n- $r_{o2}$ = output resistance of M₂ = $\\frac{1}{\\lambda_2 I_{D}}$\n\n## Key Insight\n\nThe cascode configuration provides a **much higher output resistance** than a single transistor (which would only be $r_{o1}$) by a factor of approximately $g_{m2} \\cdot r_{o2}$. This makes it excellent as a current source since the current remains more constant despite voltage variations at node X.",
        "format": "markdown",
        "sha256": "3fe36a7764758c45b80b438efb9b88fe2df287ccdae506b3ebd32062bac6cf24"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer analyzes the devices as NMOS, puts the output at X, and assigns the cascode role to M2. In the figure both devices are PMOS, Rout is measured at M1’s drain, and M1 is the cascode device, so the stated result uses the wrong topology and transconductance.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 4603,
        "total_tokens": 6214,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4178,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 4603,
        "total_tokens": 6214,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4178,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, I can see a cascode configuration with transistors M₁ and M₂ stacked vertically. The output is taken at the source of M₁ (the bottom transistor).\n\n## Small-Signal Analysis\n\nLet me find the output resistance by applying a small-signal perturbation at the output node.\n\n**For transistor M₁:**\n- Δi_{D1} = g_{m1}Δv_{GS1} + Δv_{DS1}/r_{o1}\n- Δv_{GS1} = -Δv_{out} (since V_{b1} is constant)\n- Δv_{DS1} = Δv_X - Δv_{out}\n\nTherefore:\n$$\\Delta i_{D1} = -g_{m1}\\Delta v_{out} + \\frac{\\Delta v_X - \\Delta v_{out}}{r_{o1}}$$\n\n**For transistor M₂:**\n- Δi_{D2} = g_{m2}Δv_{GS2} + Δv_{DS2}/r_{o2}\n- Δv_{GS2} = -Δv_X (since V_{b2} is constant)\n- Δv_{DS2} = -Δv_X (since V_{DD} is AC ground)\n\nTherefore:\n$$\\Delta i_{D2} = -g_{m2}\\Delta v_X - \\frac{\\Delta v_X}{r_{o2}} = -\\Delta v_X(g_{m2} + 1/r_{o2})$$\n\n**Current continuity:**\nSince Δi_{D1} = Δi_{D2}, from M₂:\n$$\\Delta v_X = -\\frac{\\Delta i_{D1}}{g_{m2} + 1/r_{o2}}$$\n\nSubstituting back and solving (with the approximation that g_m·r_o >> 1):\n\nAfter algebraic manipulation:\n$$\\Delta i_{D1} \\approx -g_{m1}\\Delta v_{out}$$\n\nSince the output current flows upward (opposite to i_{D1}):\n$$R_{out} = \\frac{\\Delta v_{out}}{\\Delta i_{out}} = \\frac{\\Delta v_{out}}{-\\Delta i_{D1}}$$\n\n## Final Answer\n\n$$\\boxed{R_{out} \\approx \\frac{1}{g_{m1}}}$$\n\nThis makes physical sense: M₁ is operating in a **source-follower (common-drain) configuration**, and the output resistance of a source follower at its source terminal is approximately 1/g_m, regardless of the load at its drain (as long as the load can supply the required AC current), which M₂ provides here.",
        "format": "markdown",
        "sha256": "342c36cc4c71224f7924e4db461eca75c51108ed338314f71d0def26085bdaff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places the output at M1’s source and treats M1 as a source follower, whereas the output is at M1’s drain and M1 is the PMOS cascode device. Its resulting 1/gm1 estimate misses the cascode output resistance.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 11282,
        "total_tokens": 12893,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10620,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 11282,
        "total_tokens": 12893,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10620,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Finding Rout for the Cascode Configuration\n\nThis circuit shows a **cascode current source** with M₁ (bottom transistor) and M₂ (top transistor stacked in a common-gate configuration).\n\n## Analysis\n\nTo find the output resistance, I'll analyze the small-signal behavior:\n\n- **M₁** operates in common-source configuration with output resistance r₀₁\n- **M₂** operates in common-gate configuration with output resistance r₀₂\n- Node X connects M₁'s drain to M₂'s source\n\nFor a cascode structure, M₂ (common-gate stage) sees an impedance r₀₁ at its source, which significantly increases the overall output resistance.\n\n## Result\n\nThe output resistance of the cascode current source is:\n\n$$R_{out} = r_{o1} + r_{o2}(1 + g_{m2}r_{o1})$$\n\nThis can be rewritten as:\n\n$$R_{out} = r_{o1} + r_{o2} + g_{m2}r_{o1}r_{o2}$$\n\n**Approximate form** (when $g_{m2}r_{o1} >> 1$):\n\n$$\\boxed{R_{out} \\approx g_{m2}r_{o1}r_{o2}}$$\n\nOr equivalently:\n$$R_{out} = A_2 \\cdot r_{o1}$$\n\nwhere $A_2 = g_{m2}r_{o2}$ is the intrinsic gain of M₂.\n\nThe cascode configuration increases the output resistance by approximately a factor of $(g_{m}r_o)$ compared to a single transistor, making it excellent for current source applications.",
        "format": "markdown",
        "sha256": "ac9cc13fe0ffefab84434a7b50ed53661c51c482d5a322dbeba678c413a52f83"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It assigns the cascode role to M2 and uses gm2 as the cascode factor; the actual output-side cascode device is M1, so Rout is approximately gm1 ro1 ro2.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 3840,
        "total_tokens": 5451,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3428,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 3840,
        "total_tokens": 5451,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3428,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Ensuring M2 is in Saturation\n\nTo ensure M2 (PMOS) remains in saturation, we need to satisfy the saturation condition:\n\n## Saturation Condition for PMOS:\n\n**V_SD ≥ V_SG - |V_tp|** (or equivalently: **V_SD ≥ |V_ov2|**)\n\nWhere:\n- V_SD = source-to-drain voltage\n- V_SG = source-to-gate voltage  \n- |V_tp| = threshold voltage magnitude\n- |V_ov2| = overdrive voltage of M2\n\n## Applied to M2:\n\nFor the circuit shown:\n- V_SD(M2) = V_DD - V_X\n- V_SG(M2) = V_DD - V_b2\n\nThis gives us the constraint:\n\n**V_DD - V_X ≥ V_DD - V_b2 - |V_tp|**\n\nSimplifying:\n\n**V_X ≤ V_b2 + |V_tp|**\n\n## Practical Design Guidelines:\n\n1. **Keep V_b2 sufficiently high** relative to node X voltage\n   \n2. **Choose appropriate V_b1** - This controls the current through M1, which affects V_X\n\n3. **Proper transistor sizing** - If M2 is too small relative to M1 or the load current, V_X may become too high\n\n4. **Design rule of thumb**: Ensure V_X is at least one overdrive voltage (|V_ov2|) below V_b2 to maintain good saturation margin\n\nThe key is maintaining adequate voltage headroom between the gate (V_b2) and drain (V_X) of M2.",
        "format": "markdown",
        "sha256": "88e9bf8ec8d5b55ece8b64cfb70dc8047b0427a12de7a3fc0c8fc4764a2d0519"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly gives M2’s PMOS saturation condition, but misses that VX is set by Vb1 and does not derive the required condition on Vb1; it instead treats Vb2 as the control.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 1037,
        "total_tokens": 2622,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 615,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 1037,
        "total_tokens": 2622,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 615,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To ensure **M2 is in saturation**, you need to satisfy the PMOS saturation condition:\n\n## Saturation Condition for M2:\n\n**V_SD,M2 ≥ V_SG,M2 - |V_tp|**\n\nWhere:\n- V_SD,M2 = V_DD - V_X\n- V_SG,M2 = V_DD - V_b2\n\nThis simplifies to:\n\n### **V_X ≤ V_b2 + |V_tp|**\n\n## Practical Ways to Ensure This:\n\n### 1. **Proper Bias Voltage Selection**\n   - Choose **V_b1 < V_b2** (typically V_b1 < V_b2 - |V_tp|)\n   - This ensures M1 drops sufficient voltage, keeping V_X low enough\n   - V_b2 should be close to V_DD but low enough to keep M2 ON (V_DD - V_b2 > |V_tp|)\n\n### 2. **Voltage Headroom Check**\n   - Verify: V_DD ≥ V_SD,M2(sat) + V_SD,M1(sat) + V_out\n   - Each transistor needs at least its overdrive voltage: |V_OV| = |V_SG - V_tp|\n\n### 3. **Device Sizing**\n   - Don't make M2 excessively wide relative to M1\n   - Wider M2 → smaller V_SD for same current → easier to leave saturation\n\n### 4. **Load Considerations**\n   - R_out should be chosen so the output voltage swing doesn't force V_X too high\n   - As V_out increases, V_X must also increase, which can push M2 into triode\n\n## Summary:\nThe key is ensuring sufficient voltage drop across M1 by setting **V_b1 significantly lower than V_b2**, so that node X stays at a low enough potential to satisfy **V_X ≤ V_b2 + |V_tp|**.",
        "format": "markdown",
        "sha256": "5ae83c00634414eee4ab66710a3d1025d5ab3d4fc7734e44d307d9f0853f5d5b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It gives the correct PMOS saturation condition and recognizes qualitatively that lowering Vb1 lowers X. However, it omits the relation VX = Vb1 + |VGS1| and substitutes an unsupported Vb1 threshold rule, so it does not establish the required bias condition.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 4181,
        "total_tokens": 5766,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3677,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 4181,
        "total_tokens": 5766,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3677,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Ensuring M2 is in Saturation\n\nTo ensure M2 operates in saturation, we need to satisfy the condition:\n\n## **VDS2 ≥ VGS2 - Vth2** (or VDS2 ≥ VOV2)\n\nGiven the circuit topology:\n- **VDS2 = VDD - VX**\n- **VGS2 = Vb2 - VX**\n\nSubstituting into the saturation condition:\n\n```\nVDD - VX ≥ (Vb2 - VX) - Vth2\nVDD ≥ Vb2 - Vth2\n```\n\n## Practical Design Requirements:\n\n### 1. **Proper Bias Voltage Selection**\n   - Choose **Vb2 ≤ VDD + Vth2**\n   - Typically set Vb2 to give adequate VGS2 while maintaining headroom\n\n### 2. **Control Node X Voltage**\n   - Ensure **VX ≤ VDD - VOV2** \n   - Keep VX sufficiently low by:\n     - Proper choice of Vb1 for M1\n     - Controlling the current through the cascode\n     - Managing the output voltage at Rout\n\n### 3. **Design Margin**\n   - Include safety margin: **VDS2 ≥ VOV2 + margin** (e.g., 0.1-0.2V)\n   - This ensures M2 stays in saturation despite process/temperature variations\n\n### 4. **Key Design Parameters**\n   - VX is typically set to ensure both M1 and M2 are in saturation\n   - In cascode configurations, VX is often designed to be: **VX = Vb1 + VOV1** (if M1's source is near ground)\n   - This leaves sufficient headroom: **VDS2 = VDD - Vb1 - VOV1**\n\n**Summary**: Choose Vb2 appropriately relative to VDD, and ensure the circuit operating point keeps VX low enough that VDS2 remains greater than VOV2.",
        "format": "markdown",
        "sha256": "e3756485a51a42d705473a283838246903bcb64df9345a7eefe26ecf97484a3c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer applies an NMOS saturation condition to a circuit with two PMOS devices and incorrectly makes the condition depend only on Vb2. It misses the key relation VX = Vb1 + |VGS1|; its generic headroom discussion earns only minimal partial credit.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 4339,
        "total_tokens": 5924,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3824,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1585,
        "output_tokens": 4339,
        "total_tokens": 5924,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3824,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Cascode Amplifier\n\n## **Circuit Topology**\nThis is a **cascode amplifier** with a current source load, consisting of:\n- **M₁**: Common-source input stage (NMOS)\n- **M₂**: Cascode transistor (NMOS)  \n- **I₁**: Active current source load\n- **V_in**: Input signal\n- **V_b1**: Bias voltage for M₂\n- **V_out**: Output node\n\n## **DC Operating Point**\n\n### Bias Conditions:\n1. Current source I₁ establishes the DC bias current through both transistors\n2. For saturation operation:\n   - **M₁**: V_DS1 = V_X > V_in - V_TH1\n   - **M₂**: V_DS2 = V_out - V_X > V_b1 - V_X - V_TH2\n\n3. V_b1 must be chosen to ensure both transistors remain in saturation\n\n## **AC Small-Signal Analysis**\n\n### Voltage Gain:\n$$A_v = \\frac{v_{out}}{v_{in}} = -g_{m1} \\cdot R_{out}$$\n\nwhere the output resistance is:\n$$R_{out} = (g_{m2} \\cdot r_{o2} \\cdot r_{o1}) \\parallel r_{o,I1}$$\n\nTypically: **A_v ≈ -g_m1 · g_m2 · r_o1 · r_o2** (very high gain)\n\n### Output Impedance:\nThe cascode configuration dramatically increases output impedance compared to a simple common-source stage.\n\n## **Key Advantages**\n\n1. ✅ **Very High Voltage Gain** - Product of transconductances and output resistances\n2. ✅ **High Output Impedance** - Excellent current source behavior\n3. ✅ **Reduced Miller Effect** - M₂ shields M₁'s drain from output voltage swings\n4. ✅ **Improved Bandwidth** - Better high-frequency response\n5. ✅ **Good Isolation** - Input and output are well isolated\n\n## **Limitations**\n\n1. ⚠️ **Reduced Voltage Headroom** - Stacked transistors limit output swing\n2. ⚠️ **Requires Precise Biasing** - V_b1 must be carefully designed\n3. ⚠️ **Increased Noise** - Two transistors contribute to total noise\n\n## **Applications**\n- Operational amplifier input stages\n- High-gain analog amplifiers\n- RF/high-frequency circuits\n- Precision analog signal processing",
        "format": "markdown",
        "sha256": "b0c8d151e578231bb23bebcb924f69d2fed49742695b41ebffa7869748ad8029"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the NMOS cascode, and gives the equivalent cascode gain approximation with an ideal current-source load. Minor omitted terms in the output-resistance approximation do not affect the result.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 1792,
        "total_tokens": 3268,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1144,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 1792,
        "total_tokens": 3268,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1144,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Cascode Amplifier with Active Load\n\n## Circuit Configuration\n\nThis is a **cascode amplifier** consisting of:\n- **M₁**: Common-source input transistor (NMOS)\n- **M₂**: Common-gate cascode transistor (NMOS)  \n- **I₁**: Active current source load\n- **Node X**: Intermediate connection between M₁ and M₂\n\n## DC Operating Point Analysis\n\n1. **Bias Current**: The current source I₁ establishes the DC bias current through both transistors (since they're in series)\n\n2. **Saturation Conditions**:\n   - **M₁**: Requires V_X ≥ V_in - V_TH1\n   - **M₂**: Requires V_out - V_X ≥ V_b1 - V_X - V_TH2, or V_out ≥ V_b1 - V_TH2\n\n3. **Bias Voltage**: V_b1 must be set appropriately to keep M₂ in saturation while allowing adequate voltage headroom\n\n## Small-Signal AC Analysis\n\n### Voltage Gain:\n**A_v = -g_m1 × R_out**\n\nWhere R_out is the output impedance:\n- R_out ≈ (g_m2 × r_o2 × r_o1) || r_o_current_source\n- Since r_o_current_source is very large: **R_out ≈ g_m2 × r_o2 × r_o1**\n\nTherefore: **A_v ≈ -g_m1 × g_m2 × r_o2 × r_o1**\n\n### Input Impedance:\nZ_in ≈ ∞ (gate of M₁)\n\n### Output Impedance:\nVery high due to cascode configuration (~g_m2 × r_o2 × r_o1)\n\n## Key Advantages\n\n1. **High Voltage Gain**: Much higher than simple common-source due to increased output impedance\n2. **Reduced Miller Effect**: M₂ shields M₁ from output voltage variations\n3. **Improved Bandwidth**: Better high-frequency performance\n4. **High Output Impedance**: Excellent current source for other stages\n\n## Applications\n\n- High-gain amplifier stages\n- Analog signal processing\n- Operational amplifier design\n- High-performance analog ICs",
        "format": "markdown",
        "sha256": "f60f5c3b0a692888c1eddc963dd6659ace0a0fa01da3d71eeee2268bfb7b5822"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain −gm1·gm2·ro2·ro1. Omitting body effect is allowed by the full-credit rule.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 2026,
        "total_tokens": 3502,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1435,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 2026,
        "total_tokens": 3502,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1435,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Cascode Amplifier\n\n## **Circuit Configuration**\n\nThis is a **cascode amplifier** (also called a common-source common-gate amplifier) with the following components:\n\n- **M₁**: NMOS input transistor (common-source configuration)\n- **M₂**: NMOS cascode transistor (common-gate configuration)  \n- **I₁**: Current source load\n- **V_b1**: Bias voltage for M₂\n- **V_in**: Input signal\n- **V_out**: Output signal\n\n## **DC Operating Point**\n\nThe current source I₁ establishes the DC bias current through both transistors:\n\n- **I_D1 = I_D2 = I₁** (same current through series devices)\n- **V_X ≈ V_GS1** (voltage at intermediate node)\n- **V_b1** must be set to ensure both transistors remain in saturation\n\nFor proper operation:\n- M₁: V_DS1 > V_GS1 - V_TH1\n- M₂: V_DS2 > V_GS2 - V_TH2\n\n## **Small-Signal Analysis**\n\n### **Voltage Gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} = -g_{m1} \\cdot r_{o1} \\cdot (1 + g_{m2} \\cdot r_{o2})$$\n\nFor typical operation where $g_{m2} \\cdot r_{o2} \\gg 1$:\n\n$$A_v \\approx -g_{m1} \\cdot g_{m2} \\cdot r_{o1} \\cdot r_{o2}$$\n\n### **Output Resistance:**\n$$R_{out} \\approx r_{o1}(1 + g_{m2} \\cdot r_{o2}) \\approx g_{m2} \\cdot r_{o1} \\cdot r_{o2}$$\n\nThis is significantly higher than a simple common-source stage!\n\n## **Key Advantages**\n\n1. **Very High Output Impedance**: Enhanced by factor of ~$g_{m2}r_{o2}$\n2. **High Voltage Gain**: Approximately squared compared to single transistor\n3. **Reduced Miller Effect**: M₂ shields M₁ from output voltage variations\n4. **Improved Bandwidth**: Better high-frequency performance\n5. **Better Isolation**: Input and output are well isolated\n\n## **Disadvantages**\n\n1. **Reduced Voltage Headroom**: Two stacked transistors reduce output swing\n2. **Additional Bias Required**: Needs V_b1 bias voltage\n3. **Higher Complexity**: More complex biasing circuitry\n\n## **Applications**\n\n- High-gain amplifier stages\n- Operational amplifier input stages\n- High output impedance current sources\n- RF and wideband amplifiers\n- Precision analog circuits",
        "format": "markdown",
        "sha256": "309183aec1288622ec529390012c6d973a911bfb2533234fe33fa5b7b3d5d74d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression. Omitting body effect is allowed.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 3048,
        "total_tokens": 4524,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2346,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1476,
        "output_tokens": 3048,
        "total_tokens": 4524,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2346,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, this is a cascode structure.\n\nThe circuit shown is a classic **NMOS cascode amplifier** configuration. Here's why:\n\n## Key characteristics of a cascode:\n\n1. **Two stacked transistors**: M₁ and M₂ are connected in series vertically\n\n2. **M₁ (bottom transistor)**: \n   - Input signal Vᵢₙ applied to gate\n   - Acts as a **common-source (CS) stage**\n   - Provides transconductance gain\n\n3. **M₂ (top transistor)**:\n   - Gate biased at fixed DC voltage Vb₁\n   - Source connected to drain of M₁\n   - Acts as a **common-gate (CG) stage**\n   - Acts as a current buffer\n\n4. **Output**: Taken from the drain of M₂ (top transistor)\n\n## Advantages of this cascode configuration:\n\n- **High output resistance** - dramatically increased compared to single-stage amplifier\n- **Better high-frequency performance** - reduced Miller effect\n- **Higher voltage gain** - when properly biased\n- **Improved bandwidth** - due to reduced capacitive effects\n\nThis is one of the most common cascode implementations in analog IC design.",
        "format": "markdown",
        "sha256": "7a39d833f79256a1160f0a43b989358db1676aedd2967a9a41dfb0a57f8fb062"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source input stage, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 779,
        "total_tokens": 2326,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 486,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 779,
        "total_tokens": 2326,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 486,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, this is a cascode structure.\n\nThe circuit shows a **cascode amplifier** configuration with the following key characteristics:\n\n## Cascode Structure Elements:\n\n1. **Two stacked transistors**: M₁ (bottom) and M₂ (top) connected in series\n\n2. **M₁ - Common-Source Stage**:\n   - Input signal (Vᵢₙ) applied to the gate\n   - Source connected to ground\n   - Functions as a transconductance amplifier\n\n3. **M₂ - Common-Gate Stage**:\n   - Gate held at fixed bias voltage (Vb₁)\n   - Source connected to drain of M₁\n   - Functions as a current buffer\n\n4. **Output**: Taken from the drain of M₂ through load resistor Rᴅ\n\n## Advantages of this Cascode Configuration:\n\n- **High output resistance** - improves voltage gain\n- **Reduced Miller effect** - better high-frequency performance\n- **Improved bandwidth** - compared to simple common-source amplifier\n- **Better isolation** between input and output\n\nThis is a classic textbook example of a cascode amplifier topology commonly used in analog IC design.",
        "format": "markdown",
        "sha256": "84a4d622d39f7d9061a0eec9063409d606b61123ca9fef62f0c007f4ea356a89"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source stage, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 786,
        "total_tokens": 2333,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 504,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 786,
        "total_tokens": 2333,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 504,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, this is a cascode structure.\n\nThe circuit shows a **classic cascode amplifier** configuration with the following characteristics:\n\n## Key Features:\n\n1. **M₁ (Lower transistor)**: Configured as a **common-source (CS)** amplifier\n   - Input signal (Vin) applied to the gate\n   - Source connected to ground\n   - Acts as the transconductance stage\n\n2. **M₂ (Upper transistor)**: Configured as a **common-gate (CG)** amplifier\n   - Gate held at fixed bias voltage (Vb1)\n   - Source connected to drain of M₁\n   - Acts as a current buffer\n\n3. **Stacked Connection**: The drain of M₁ connects directly to the source of M₂\n\n## Advantages of This Cascode Configuration:\n\n- **High output impedance** → Higher voltage gain\n- **Reduced Miller effect** → Better high-frequency performance\n- **Improved bandwidth** compared to a single-stage CS amplifier\n- **Better isolation** between input and output\n\nThis is a standard NMOS cascode amplifier topology commonly used in analog integrated circuits.",
        "format": "markdown",
        "sha256": "1a895851c60f5741d83310f26e6264f3d1251b2e40c9155b14859ca0db3d0f6d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode and treats M1 as a common-source device. M1 is a PMOS source follower, so the structure lacks cascode output-resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 714,
        "total_tokens": 2261,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 445,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1547,
        "output_tokens": 714,
        "total_tokens": 2261,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 445,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why Miller Effect is Reduced in a Cascode\n\n## The Miller Effect Problem\n\nIn a simple common-source (or common-emitter) amplifier, the **Miller effect** severely impacts bandwidth. The gate-drain capacitance (C_gd) appears multiplied at the input by a factor of **(1 + A_v)**, where A_v is the voltage gain:\n\n**C_input_miller = C_gd(1 + A_v)**\n\nWith high gain (say, A_v = 50), even a small 1 pF capacitance becomes 51 pF at the input!\n\n## How the Cascode Solves This\n\nA cascode consists of two transistors:\n- **Bottom transistor (M1)**: Common-source/emitter configuration  \n- **Top transistor (M2)**: Common-gate/base configuration\n\n### Key Reason 1: Bottom Stage Has Minimal Voltage Gain\n\nThe output node of M1 (source of M2) experiences very little voltage swing because:\n- It's loaded by the **low input impedance** of the common-gate stage (≈ 1/g_m2)\n- Voltage gain of first stage: **A_v1 ≈ -g_m1/g_m2 ≈ -1** (for matched transistors)\n\nTherefore: **C_miller1 = C_gd1(1 + 1) = 2C_gd1** — nearly the bare capacitance!\n\n### Key Reason 2: Top Stage Doesn't Contribute Miller Effect at the Input\n\nThe common-gate stage provides all the voltage gain, BUT:\n- Its gate is at **AC ground** (constant voltage)\n- C_gd2 connects between the output and AC ground (not between input and output)\n- No capacitance bridges the input and output with the same polarity that creates Miller multiplication\n\n## The Result\n\nThe cascode achieves **high gain without high input capacitance**, making it excellent for high-frequency applications. The bandwidth is dramatically improved compared to a single-stage amplifier with the same gain.",
        "format": "markdown",
        "sha256": "1f8a4613a21dc54045c999837de1132833a30bf1852c6d0f819066494f666734"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance M2 source node and the resulting gain of about −1 across Cgd1, giving roughly 2× capacitance rather than multiplication by the full stage gain. Calling this nearly bare capacitance slightly overstates the reduction, but the central reasoning and numerical result are correct.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1657,
        "total_tokens": 1707,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1165,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1657,
        "total_tokens": 1707,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1165,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why Miller Effect is Reduced in a Cascode\n\n## Quick Answer\nThe cascode configuration minimizes Miller effect because the **bottom transistor has very low voltage gain** at its drain/collector node, which dramatically reduces the Miller multiplication of its parasitic capacitance.\n\n## The Miller Effect Problem\n\nIn a standard common-source (CS) or common-emitter (CE) amplifier:\n- The gate-drain capacitance (Cgd) or base-collector capacitance (Cbc) experiences high voltage swing\n- This capacitance gets multiplied by the **Miller effect**: \n  \n  **C_Miller = Cgd × (1 + |Av|)**\n\n- With high gain (Av might be 20-100), a tiny 1pF capacitance becomes 20-100pF at the input\n- This severely limits bandwidth\n\n## How Cascode Solves This\n\n### Bottom Transistor (CS/CE stage):\n- Its drain/collector node sees **very small voltage swing**\n- The top transistor acts as a **low-impedance current source load** (common-gate/common-base input impedance ≈ 1/gm)\n- Local voltage gain at this node ≈ **-1 to -2** (instead of -20 to -100)\n- Therefore: C_Miller ≈ Cgd × (1 + 2) = **3×Cgd** (manageable!)\n\n### Top Transistor (CG/CB stage):\n- Its gate/base is at **AC ground** (biased with fixed voltage)\n- Gate-drain capacitance doesn't couple to the input\n- No Miller multiplication affects the signal path\n\n## Result\n- Input capacitance is dramatically reduced\n- Bandwidth increases significantly (often 10-20× improvement)\n- The cascode achieves high overall gain while keeping the critical input node free from Miller multiplication\n\nThis is why cascodes are essential in **high-frequency amplifiers**, **wideband circuits**, and **RF design**.",
        "format": "markdown",
        "sha256": "da5570d188cf369b0380407c5d2bf87ca0fbf65be14195ccde41746c916be3ca"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the low-impedance common-gate source node and the reduced gain across the input transistor’s Cgd. However, the typical Miller factor is about 2 rather than 3, and saying the input is “free from Miller multiplication” overstates the effect, which is reduced but not eliminated.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1289,
        "total_tokens": 1339,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 822,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1289,
        "total_tokens": 1339,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 822,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Miller Effect Reduction in Cascode Amplifiers\n\nThe Miller effect is significantly reduced in a cascode configuration due to the **low voltage gain at the critical intermediate node**. Here's why:\n\n## The Miller Effect Problem\n\nIn a simple common-source/common-emitter amplifier:\n- The gate-drain capacitance (Cgd) experiences the full voltage gain: **Av = -gm·RL**\n- Miller multiplication makes the input capacitance: **Cin = Cgd(1 + |Av|)**\n- With high gain (e.g., Av = -50), a 1pF capacitance becomes 51pF\n- This drastically limits bandwidth\n\n## How Cascode Reduces Miller Effect\n\n### 1. **Low Impedance at Intermediate Node**\n```\nInput → [M1: Common-Source] → [M2: Common-Gate] → Output\n                  ↑\n            Low impedance\n            (≈ 1/gm2)\n```\n\nThe drain of M1 (input transistor) connects to the source of M2, which presents a **low input impedance** of approximately **1/gm2**.\n\n### 2. **Minimal Voltage Swing at M1's Drain**\n\nThe voltage gain from input to the drain of M1 is:\n\n**Av1 ≈ -gm1 × (1/gm2) ≈ -1**\n\nThis is drastically smaller than the gain in a single-stage amplifier (-gm1·RL).\n\n### 3. **Reduced Capacitance Multiplication**\n\nThe Miller capacitance becomes:\n- **Cin_Miller = Cgd(1 - Av1) ≈ Cgd(1 + 1) = 2·Cgd**\n\nCompare this to a single stage where it might be 50·Cgd or more!\n\n### 4. **Gain Occurs Elsewhere**\n\nThe overall voltage gain is still high (**Av_total ≈ -gm1·RL**), but this gain appears **at the output of M2**, not across Cgd of M1. The cascode effectively isolates the input from the output.\n\n## Result\n\nThe cascode maintains **high gain and high output impedance** while achieving **much wider bandwidth** due to the minimized Miller effect.",
        "format": "markdown",
        "sha256": "30c50a89307579f4eed780d1618929c276816dcd146278d75f4988d2c14095c8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that M2 presents a low impedance at M1’s drain, limiting the gain across Cgd1 to about −1 and its Miller multiplication to roughly 2 rather than the full-stage gain. The approximations are appropriate.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1732,
        "total_tokens": 1782,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1179,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 1732,
        "total_tokens": 1782,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1179,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Type\nThis is a **common-source amplifier with active PMOS load**, a fundamental building block in analog integrated circuits.\n\n## Circuit Components\n\n- **M₁ (PMOS)**: Active load transistor\n  - Source → V_DD\n  - Gate → V_b2 (bias voltage)\n  - Drain → V_out\n\n- **M₂ (NMOS)**: Input/driver transistor  \n  - Gate → V_in (signal input)\n  - Drain → V_out\n  - Source → V_b1 (bias voltage)\n\n## Operating Principle\n\n### DC Biasing\n1. **V_b2** sets the gate voltage of M₁, establishing the bias current\n2. **V_b1** sets the source potential of M₂ (typically ground or low voltage)\n3. The DC operating point satisfies: **I_D1 = I_D2**\n4. V_out settles at a voltage where both transistors conduct the same current\n\n### AC Operation\n- **Input:** Signal applied to M₂'s gate (V_in)\n- **M₂ function:** Transconductance stage (converts voltage to current)\n- **M₁ function:** Active current-source load (high impedance)\n- **Output:** Amplified, inverted signal at V_out\n\n## Key Characteristics\n\n### Voltage Gain\n$$A_v \\approx -g_{m2} \\cdot (r_{o1} \\parallel r_{o2})$$\n\nWhere:\n- g_m2 = transconductance of M₂\n- r_o1, r_o2 = output resistances of M₁ and M₂\n- Negative sign indicates **180° phase inversion**\n\n### Advantages\n- ✓ High voltage gain (due to high output impedance)\n- ✓ No resistors needed (IC-friendly)\n- ✓ Low power consumption\n- ✓ Good PSRR (Power Supply Rejection Ratio)\n\n### Output Voltage Range\nMust satisfy: **V_b1 + V_eff,2 < V_out < V_DD - |V_eff,1|**\n\nfor both transistors to remain in saturation (active region).\n\n## Applications\n- Operational amplifier input stages\n- Analog signal processing\n- Voltage amplification in mixed-signal ICs",
        "format": "markdown",
        "sha256": "55768986da31adedfb5187d358faa91e6117cab9f3821acf1cf32a5bcaf1f80a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2's gate and identifies a common-source stage, but the circuit is common-gate with Vin applied at M2's source; the golden solution explicitly assigns 0 for this topology error.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 1988,
        "total_tokens": 3348,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 1988,
        "total_tokens": 3348,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Common-Source Amplifier with Active Load\n\n## Circuit Configuration\n\nThis is a **common-source (CS) amplifier with PMOS active load** - a fundamental building block in analog integrated circuits.\n\n## Component Identification\n\n- **M1**: PMOS transistor (active load/current source)\n- **M2**: NMOS transistor (input/amplifying device)\n- **Vb2**: Bias voltage for M1 gate\n- **Vb1**: Source bias/ground reference for M2\n- **Vin**: AC input signal\n- **Vout**: Output signal node\n\n## Circuit Operation\n\n### DC Bias\n1. **M1** operates as a current source, with Vb2 setting its gate voltage to establish a bias current\n2. **M2** source is connected to Vb1 (typically ground), with Vin biased to keep M2 in saturation\n3. Both transistors share the same drain current at DC\n\n### AC Operation\n- Input signal Vin modulates M2's gate voltage\n- This changes the drain current of M2\n- M1 acts as a high-impedance load\n- Small current changes produce large voltage swings at Vout\n\n## Key Performance Metrics\n\n**Voltage Gain:**\n$$A_v = -g_{m2}(r_{o1} \\parallel r_{o2})$$\n\nWhere:\n- gm2 = transconductance of M2\n- ro1, ro2 = output resistances of M1 and M2\n\n**Characteristics:**\n- **High voltage gain** (due to active load's high impedance)\n- **Inverting amplifier** (180° phase shift)\n- **High output impedance**: ro1 || ro2\n- **Single-ended output**\n\n## Applications\n- Operational amplifier input stages\n- Analog signal processing\n- Voltage amplification in integrated circuits",
        "format": "markdown",
        "sha256": "e123493b001dc1e747a94b5ed224e4a5d3f91265a60601a05b1990575ebae380"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2’s gate and identifies the stage as common-source, but the circuit is common-gate with Vin at M2’s source. Its inverting gain conclusion is therefore wrong.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 1829,
        "total_tokens": 3189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1385,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 1829,
        "total_tokens": 3189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1385,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Type\nThis is a **single-stage common-source (CS) amplifier with active load**, a fundamental building block in analog CMOS integrated circuits.\n\n## Circuit Components\n\n- **M₁ (PMOS)**: Acts as an **active load** (current source load)\n  - Gate biased at V_b2\n  - Source connected to V_DD\n  - Drain connected to output node\n\n- **M₂ (NMOS)**: Acts as the **input/amplifying transistor**\n  - Gate receives input signal V_in\n  - Source connected to V_b1 (likely ground or bias point)\n  - Drain connected to output node\n\n## DC Operating Point\n\n1. **Bias conditions:**\n   - V_b2 sets the gate voltage of M₁, determining its drain current\n   - V_b1 sets the source potential of M₂\n   - At equilibrium: I_D1 = I_D2\n\n2. **For M₁ (saturation):** \n   - I_D1 = ½μ_pC_ox(W/L)₁(V_SG - |V_thp|)²\n\n3. **For M₂ (saturation):**\n   - I_D2 = ½μ_nC_ox(W/L)₂(V_GS - V_thn)²\n\n## Small-Signal Analysis\n\n**Voltage Gain:**\n$$A_v = -g_{m2}(r_{o1} \\parallel r_{o2})$$\n\nWhere:\n- g_m2 = transconductance of M₂ = √(2μ_nC_ox(W/L)₂I_D)\n- r_o1 = output resistance of M₁ = 1/(λ_pI_D)\n- r_o2 = output resistance of M₂ = 1/(λ_nI_D)\n\n## Key Characteristics\n\n| Parameter | Value/Description |\n|-----------|------------------|\n| **Gain** | Medium-high (20-60 dB typical) |\n| **Input Impedance** | Very high (~∞) |\n| **Output Impedance** | r_o1 ∥ r_o2 (kΩ range) |\n| **Phase Shift** | 180° (inverting) |\n| **Bandwidth** | Limited by parasitic capacitances |\n\n## Applications\n- Voltage amplification stages\n- Operational amplifier input stages  \n- Analog signal processing\n- High-gain amplifier stages in analog ICs",
        "format": "markdown",
        "sha256": "6ac65be5d4d93e3701d29089042ec7bffff07e504cdb726af03a1167f0fe359d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2's gate and misidentifies the stage as an inverting common-source amplifier. The circuit is common-gate, with Vin at M2's source, non-inverting gain, and low input resistance; the golden solution explicitly assigns 0 when Vin is placed at the gate.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 3279,
        "total_tokens": 4639,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2655,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1360,
        "output_tokens": 3279,
        "total_tokens": 4639,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2655,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this cascode amplifier circuit, I need to identify the nodes where capacitances create poles in the transfer function.\n\n## Analysis of Poles\n\nThe circuit has **3 poles** located at three distinct nodes:\n\n### 1. **Input Pole** (Gate of M₁)\n- Capacitances: C_GS and C_GD\n- Resistance: Rs (source resistance)\n- This creates a pole at the input node\n\n### 2. **Intermediate Pole** (Drain of M₁/Source of M₂)\n- Capacitances: C_GD (of M₁), C_DB, and parasitic capacitances\n- Resistance: Approximately 1/g_m2 (low impedance looking into source of M₂)\n- This pole is typically at very high frequency due to the low impedance at this node in the cascode configuration\n\n### 3. **Output Pole** (Drain of M₂)\n- Capacitances: C_DB2 and C_GD2\n- Resistance: High output resistance of the cascode stage (r_o1 + r_o2)\n- This creates the dominant output pole\n\n## Answer: **3 poles**\n\n**Note:** While the circuit technically has 3 poles, the intermediate pole is often at such a high frequency that it's negligible in practical analysis. Many engineers focus on just the 2 dominant poles (input and output) for frequency response calculations. However, for a complete pole count, the answer is **3 poles**.",
        "format": "markdown",
        "sha256": "c9b096f20198335b381a413e15238176a94b3ae64014fc7f69a236061a58e804"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives the wrong pole count and misidentifies the circuit as a cascode, inventing an intermediate node. It does mention some relevant input and output capacitances, but the actual circuit has two poles.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 3978,
        "total_tokens": 5577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3621,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 3978,
        "total_tokens": 5577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3621,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this two-stage MOSFET amplifier circuit, I need to identify the number of poles in its transfer function by analyzing the circuit topology and capacitive nodes.\n\n## Circuit Analysis\n\nThis appears to be a **two-stage common-source amplifier** with:\n- M₁ as the input stage\n- M₂ as the output stage  \n- Various parasitic capacitances labeled (CGS, CGD, CDB, CGD2, CDB2)\n\n## Identifying the Poles\n\nThe poles are determined by the RC time constants at nodes where charge can accumulate. For this circuit, there are three main capacitive nodes:\n\n1. **Input Node (Gate of M₁):**\n   - Capacitance: CGS and CGD (with Miller multiplication)\n   - Resistance: Rs and the impedance looking into the gate\n   - Creates the **first pole**\n\n2. **Interstage Node (Drain of M₁):**\n   - Capacitance: CDB, CGD, and input capacitance of M₂ stage\n   - Resistance: Output resistance of M₁ in parallel with input impedance of M₂\n   - Creates the **second pole**\n\n3. **Output Node (Drain of M₂):**\n   - Capacitance: CDB2, CGD2, and any load capacitance\n   - Resistance: Output resistance of M₂ and load\n   - Creates the **third pole**\n\n## Answer\n\nThe circuit has **3 poles**.\n\nThese correspond to the three dominant poles at the input, interstage, and output nodes of the two-stage amplifier. The coupling/bypass capacitors shown create additional low-frequency poles, but the question typically refers to the dominant high-frequency poles created by the parasitic device capacitances.",
        "format": "markdown",
        "sha256": "a3b822cc63fcbd305d406df912f5cb4fe8675c9c3a8242f006f5990bd4977308"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The circuit is a common-source stage with a PMOS current-source load, not a two-stage amplifier. The drains of M1 and M2 are the same output node, so the answer incorrectly splits that node and concludes three poles instead of two.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5346,
        "total_tokens": 6945,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5346,
        "total_tokens": 6945,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this cascode amplifier circuit, I need to identify the independent capacitive nodes that create poles in the transfer function from V_in to V_out.\n\n## Identifying the Capacitive Nodes:\n\n**Node 1: Input (Gate of M₁)**\n- Has C_GS to ground and C_GD to the intermediate node\n- Time constant formed by R_S and the input capacitance\n- **Creates Pole 1** ✓\n\n**Node 2: Intermediate (Drain of M₁/Source of M₂)**\n- Has C_GD (from M₁) and C_GD2 (from M₂) connected to it\n- Low impedance (~1/g_m2 looking into source of M₂)\n- **Creates Pole 2** (high-frequency pole) ✓\n\n**Node 3: Output (Drain of M₂)**\n- Has C_DB and C_DB2 connected to it\n- High output impedance\n- **Creates Pole 3** ✓\n\n## Answer: **3 poles**\n\n**Clarification:**\n- In detailed small-signal analysis, there are **3 poles**\n- In simplified analyses, often only **2 dominant poles** are considered (input and output), since the intermediate node pole is at much higher frequency due to the low impedance at that node\n- The complete transfer function is third-order with 3 poles\n\nThe most accurate answer is **3 poles**, though you may also see this circuit described as having \"2 dominant poles\" in introductory treatments.",
        "format": "markdown",
        "sha256": "1fb90407a67a592b237200cc5e0e02440c3a9b5e93d2acc2b35f403033222d67"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The circuit is not a cascode and has only two independent capacitive nodes: M1’s gate and the output. The proposed intermediate node and third pole come from a misread topology.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5425,
        "total_tokens": 7024,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5058,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1599,
        "output_tokens": 5425,
        "total_tokens": 7024,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5058,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Modified Cascode Amplifier\n\n## Circuit Configuration\n\nThis circuit shows a **modified cascode amplifier** (or pseudo-cascode) with the following components:\n\n- **M₁**: NMOS transistor (bottom) - input/common-source stage\n- **M₂**: NMOS transistor (top) - cascode device  \n- **R_D**: Drain load resistor\n- **V_DD**: Power supply\n- **V_in**: Input signal\n- **V_out**: Output signal\n\n## Key Characteristics\n\n### Topology\nUnlike a traditional cascode amplifier where M₂'s gate has a fixed DC bias, **both transistor gates are connected to the input signal V_in**. This is an unconventional but functional configuration.\n\n### DC Operation\n- Both transistors carry the same drain current (series connection)\n- Both M₁ and M₂ must operate in saturation region\n- Output DC voltage: **V_out = V_DD - I_D·R_D**\n\n## Performance Features\n\n### Advantages:\n1. **High voltage gain** - Cascode configuration provides excellent gain\n2. **High output impedance** - Enhanced by the cascode structure\n3. **Reduced Miller effect** - M₁'s drain-gate capacitance is shielded by M₂\n4. **Wide bandwidth** - Due to reduced capacitive effects\n\n### Signal Behavior:\nWhen V_in increases:\n- M₁ conducts more current (↑ V_GS1)\n- M₂ also receives higher gate voltage\n- Both transistors respond simultaneously to enhance current flow\n- V_out decreases (inverting configuration)\n\n## Applications\n- High-gain amplifier stages\n- RF amplifiers\n- Low-noise amplifiers (LNA)\n- Signal conditioning circuits\n\nThis configuration combines the benefits of cascode topology with simplified biasing, though it requires careful design to ensure both transistors remain in saturation across the signal range.",
        "format": "markdown",
        "sha256": "9fabf27eda68dc18697fc7862957f9f74cdc86f5175c746bb486d7b816de1e84"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misanalyzes the common-gate-driven series NMOS pair as a cascode with both devices saturated, missing the lower device’s triode operation and the longer-effective-channel behavior.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1896,
        "total_tokens": 3449,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1438,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1896,
        "total_tokens": 3449,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1438,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: NMOS Cascode Amplifier\n\n## **Circuit Configuration**\n\nThis is a **self-cascode (or regulated cascode) amplifier** with the following topology:\n- **M₁**: NMOS transistor with source grounded, gate at V_in\n- **M₂**: NMOS transistor with source connected to M₁'s drain, gate at V_in  \n- **R_D**: Drain load resistor connected to V_DD\n- **V_out**: Output taken from the drain of M₂\n\n## **Key Characteristics**\n\n### **1. DC Operating Point**\n- Both transistors share the same gate voltage V_in\n- For proper operation, both must be in saturation:\n  - M₁: V_GS1 = V_in\n  - M₂: V_GS2 = V_in - V_X (where V_X is the intermediate node voltage)\n- The drain current is the same through both transistors: I_D = I_D1 = I_D2\n\n### **2. Small-Signal Performance**\n\n**Voltage Gain:**\n- Higher than a simple common-source amplifier\n- Both transistors modulate simultaneously with V_in\n- Approximate gain: A_v ≈ -g_m·R_out (where R_out is the effective output resistance)\n\n**Output Resistance:**\n- Significantly higher than single-stage amplifier\n- R_out ≈ r_o2(1 + g_m2·r_o1) || R_D\n- The cascode effect increases output resistance\n\n**Input Impedance:**\n- High (gate input of M₁)\n\n## **Advantages**\n\n1. **High output resistance** - improved current source behavior\n2. **Reduced Miller effect** - better high-frequency response\n3. **Higher gain** than single transistor\n4. **Better reverse isolation**\n\n## **Applications**\n\n- High-gain amplifier stages\n- Current mirrors with high output resistance\n- RF and analog integrated circuits\n- Low-voltage analog design\n\n## **Design Considerations**\n\n- Requires careful biasing to keep both transistors in saturation\n- Limited output voltage swing (at least V_DS1(sat) + V_DS2(sat) headroom needed)\n- The configuration trades voltage headroom for gain and bandwidth",
        "format": "markdown",
        "sha256": "e442ced2c6a216a3806ec171c82d20f954fb3edac7913d662efbd56b6241dd78"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It treats the shared-gate series NMOS pair as a true cascode with both devices in saturation and claims cascode-level output resistance. The essential result—that the lower device is in triode and the pair behaves approximately like one transistor with a longer effective channel—is missing.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1474,
        "total_tokens": 3027,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 927,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1474,
        "total_tokens": 3027,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 927,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis - Two-Stage NMOS Amplifier\n\n## Circuit Configuration\n\nThis is a **two-transistor NMOS amplifier circuit** consisting of:\n- **M₁**: NMOS transistor (input stage) with source grounded\n- **M₂**: NMOS transistor (upper stage) in series with M₁  \n- **R_D**: Drain resistor (load) connected to V_DD\n- Both gates connected to **V_in**\n- Output taken at the **junction between M₁ and M₂**\n\n## Circuit Topology\n\nThis is a **source-follower with current sink** configuration, also known as a:\n- **Common-drain amplifier** (for M₂)\n- **Level shifter circuit**\n\n## Operating Principle\n\n### When V_in < V_TH:\n- Both transistors are **OFF**\n- V_out ≈ **V_DD** (pulled up through R_D)\n- No DC current flows\n\n### When V_in > V_TH:\n1. **M₁ conducts**: Acts as a current sink\n2. **M₂ operates as source follower**: \n   - V_GS2 = V_in - V_out\n   - For M₂ to conduct: V_out < V_in - V_TH\n3. **Equilibrium**: V_out tracks V_in with approximately V_TH offset\n\n## Key Characteristics\n\n**Voltage Transfer:**\n- V_out ≈ V_in - V_TH (when both transistors are in saturation)\n- Acts as a **voltage buffer** with level shifting\n\n**Advantages:**\n- Low output impedance\n- Good current drive capability\n- Level shifting functionality\n\n**Applications:**\n- Voltage buffer\n- Level shifter\n- Impedance matching stage\n- Analog signal conditioning\n\n## DC Operating Point\n\nThe steady-state output voltage is determined by:\n$$V_{out} = V_{in} - V_{TH} - \\frac{I_D}{\\beta_2}$$\n\nwhere the current is set by the balance between M₁, M₂, and R_D.",
        "format": "markdown",
        "sha256": "db8297be8a38f3e9dc2973af1c83fa7bd774de1ab1344ec6716a779383a20fcd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It recognizes the series NMOS pair and common gate drive, but places the output at the internal node and analyzes M2 as a source follower. This misses the actual operating regions and the key result that the pair acts approximately like a transistor with a longer effective channel.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1907,
        "total_tokens": 3460,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1397,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1553,
        "output_tokens": 1907,
        "total_tokens": 3460,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1397,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Differential Pair Amplifier\n\n## Circuit Identification\n\nThis is a **source-coupled differential pair** (also called a long-tailed pair) with **single-ended output**. It's a fundamental building block in analog integrated circuits.\n\n## Circuit Components\n\n- **M₁**: NMOS input transistor (gate = Vᵢₙ)\n- **M₂**: NMOS transistor (gate = Vᵦ, bias voltage)\n- **I₁**: Tail current source (provides constant bias current)\n- **R_D**: Drain load resistor\n- **V_DD**: Power supply\n- **Vᵢₙ**: Signal input\n- **Vᵦ**: Reference/bias voltage\n- **Vₒᵤₜ**: Output voltage\n\n## DC Operating Point\n\n1. Current source I₁ provides constant tail current\n2. This current splits between M₁ and M₂: **I₁ = I_D1 + I_D2**\n3. Common source voltage: **V_S = Vᵢₙ - V_GS1 = Vᵦ - V_GS2**\n4. Output voltage: **Vₒᵤₜ = V_DD - I_D2·R_D**\n5. If Vᵢₙ = Vᵦ and transistors are matched: **I_D1 = I_D2 = I₁/2**\n\n## AC Small-Signal Analysis\n\nWhen Vᵢₙ changes:\n- △Vᵢₙ increases → I_D1 increases → I_D2 decreases (since I₁ is constant)\n- I_D2 decreases → voltage drop across R_D decreases\n- Therefore, **Vₒᵤₜ increases** (non-inverting gain)\n\n## Voltage Gain\n\nFor matched transistors (g_m1 = g_m2 = g_m):\n\n**A_v = (g_m · R_D)/2**\n\nMore precisely, including output resistance:\n\n**A_v = g_m · (R_D || r_o2)/2**\n\n## Key Features\n\n✓ **High input impedance** (MOS gate)  \n✓ **Good common-mode rejection** due to current source  \n✓ **Linear differential operation** for small signals  \n✓ **Temperature-stable** biasing with current source  \n✓ **Rail-to-rail output swing** potential  \n\n## Applications\n\n- Operational amplifier input stages\n- Differential-to-single-ended converters\n- Analog comparators\n- High-gain amplifier stages\n- Sensor interface circuits\n\n## Design Considerations\n\n1. **Transistor matching**: M₁ and M₂ should be matched for optimal CMRR\n2. **Current source quality**: High output impedance of I₁ improves CMRR\n3. **Load resistor**: R_D value trades off gain vs. voltage headroom\n4. **Bias point**: Vᵦ sets the DC operating point",
        "format": "markdown",
        "sha256": "244865206bbb2de17229e345cbf2630bc2b0d4167f5cd2933bbe8f13c02382ff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-coupled differential pair with M2 biased at Vb and the output at its drain. The non-inverting signal direction and matched-device gain of approximately gm·RD/2 are also correct.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 3402,
        "total_tokens": 4980,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2650,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 3402,
        "total_tokens": 4980,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2650,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: PMOS-NMOS Cascode Amplifier\n\n## Circuit Configuration\n\nThis is a **cascode amplifier** with the following structure:\n- **M₁ (NMOS)**: Common-source input stage\n- **M₂ (PMOS)**: Common-gate cascode stage  \n- **I₁**: Bias current source\n- **R_D**: Load resistor\n- **V_b**: Bias voltage for M₂'s gate\n\n## DC Operating Point Analysis\n\n**Current Flow:**\n- Current I₁ flows through both M₁ and M₂ (series connection)\n- I_D1 = I_D2 = I₁\n\n**Voltage Relations:**\n- Let V₁ = intermediate node voltage (between M₁ drain and M₂ source)\n- V_out = V_DD - I₁·R_D\n- V₁ is set by M₁'s characteristics and V_in\n\n**Saturation Conditions:**\n- M₁: V_DS1 = V₁ > V_GS1 - V_th1\n- M₂: V_SD2 = V₁ - V_out > |V_SG2| - |V_th2|\n\n## Small-Signal Analysis\n\n**Voltage Gain:**\n\nA_v = v_out/v_in = -g_m1 · (R_out || R_D)\n\nWhere the cascode output resistance is:\n- R_out ≈ (g_m2 · r_o2) · r_o1\n\nSince cascode output resistance is typically very high:\n- **A_v ≈ -g_m1 · R_D**\n\n**Output Resistance:**\n- R_out,total = R_D || [r_o2(1 + g_m2·r_o1)] ≈ R_D (if cascode R_out >> R_D)\n\n**Input Resistance:**\n- R_in ≈ ∞ (gate of MOSFET)\n\n## Key Advantages\n\n1. **High output impedance** - Better current source behavior\n2. **Reduced Miller effect** - Improved bandwidth\n3. **Higher gain** - Compared to simple common-source\n4. **Better isolation** - Input-output capacitance minimized\n\n## Key Disadvantages\n\n1. **Reduced voltage swing** - Needs headroom for both transistors\n2. **Complex biasing** - Requires proper V_b setting\n3. **Higher supply voltage** - Required for proper operation\n\n## Applications\n\n- High-gain analog amplifiers\n- Operational amplifier input stages\n- Current mirrors with high output resistance\n- RF amplifier stages",
        "format": "markdown",
        "sha256": "723acb4e15e01c148025568e1ada26218233e10fa320ac1bc73a0493f0ce5ca8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source-coupled pair as a common-source/cascode amplifier. M1 is a source follower driving M2’s common-gate stage, and the tail current splits between the devices rather than flowing through them in series.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 1976,
        "total_tokens": 3554,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1328,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 1976,
        "total_tokens": 3554,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1328,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Type\nThis is a **two-stage amplifier** consisting of:\n1. **Common-source input stage** (M₁) \n2. **Source-follower output stage** (M₂ acting as a diode-connected load)\n\n## Topology Description\n\n**Key connections:**\n- M₁ (NMOS): Input transistor with gate driven by V_in\n- M₂ (PMOS): Diode-connected (gate tied to drain), configured as source follower\n- The drains of M₁ and M₂ are connected together (node V_x)\n- I₁: Provides constant current bias for M₁\n- R_D: Pull-up resistor from V_DD to output\n- V_b: Body bias for M₂\n\n## DC Operating Point\n\n**Current flow:**\n- Current I₁ flows through both M₁ and M₂\n- At node V_out: $I_{R_D} = I_1$\n\n**DC output voltage:**\n$$V_{out} = V_{DD} - I_1 \\cdot R_D$$\n\n**Internal node V_x:**\n- Determined by M₂'s diode connection: $V_{GS2} = V_{DS2}$\n- $V_x = V_{out} - |V_{GS2}|$\n\n## Small-Signal Analysis\n\n**Voltage gain:**\n\nAt the internal node (common drains):\n$$v_x = g_{m1} \\cdot v_{in} \\cdot Z_x$$\n\nwhere $Z_x \\approx \\frac{1}{g_{m2}} \\parallel r_{o1} \\parallel r_{o2}$\n\nSince M₂ acts as a source follower, the output follows the gate voltage:\n$$v_{out} \\approx v_x$$\n\n**Overall voltage gain:**\n$$A_v = \\frac{v_{out}}{v_{in}} \\approx \\frac{g_{m1}}{g_{m2}}$$\n\nIf M₁ and M₂ are designed with equal transconductance, then **A_v ≈ 1** (unity gain buffer).\n\n## Circuit Characteristics\n\n**Advantages:**\n- Low output impedance (due to source-follower M₂)\n- Good current driving capability\n- Level shifting between input and output\n- Stable biasing with current source\n\n**Applications:**\n- **Buffer amplifier** (if g_m1 ≈ g_m2)\n- **Level shifter**\n- **Output driver stage**\n- **Interstage coupling** in multi-stage amplifiers\n\n## Output Impedance\n\nThe output impedance is:\n$$Z_{out} = R_D \\parallel r_{out,M2}$$\n\nwhere $r_{out,M2} \\approx \\frac{1}{g_{m2}}$ (looking into source of M₂)\n\nThis provides relatively low output impedance suitable for driving subsequent stages.",
        "format": "markdown",
        "sha256": "3b0b0c4f693860aefa347e31dc3b99abae1c2fa451495989aae379c1e2e81a0b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the circuit as a common-source stage with a diode-connected PMOS load and tied drains. The actual circuit is a source follower driving a common-gate stage (or a source-coupled pair), so its topology and gain analysis are incorrect.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 3629,
        "total_tokens": 5207,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2919,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1578,
        "output_tokens": 3629,
        "total_tokens": 5207,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2919,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why the Output Impedance Can Be Inductive\n\nThis circuit is a common-source amplifier with M₁ as the active device, M₂ as a current source load, and Rs as source resistance at the input. The output impedance can exhibit **inductive behavior** due to feedback through the gate-drain capacitance (Cgd) and Rs.\n\n## Physical Mechanism\n\nWhen analyzing the small-signal output impedance at Vout:\n\n### 1. **Feedback Path**\n- Changes in Vout couple back to the gate of M₁ through the gate-drain capacitance (Cgd)\n- Current flows: `i_cgd = jωCgd(Vout - Vg)`\n- This current must flow through Rs to ground (when Vin = 0 for AC analysis)\n- This creates: `Vg = -i_cgd · Rs`\n\n### 2. **Transconductance Effect**\n- The gate voltage change affects Vgs: `Vgs = Vg`\n- This modulates the drain current: `i_d = gm₁ · Vgs`\n- When gm₁·Rs > 1, the transconductance current change **exceeds** the direct capacitive current\n\n### 3. **Critical Condition**\n\nThe output admittance has a susceptance component:\n\n$$B = \\frac{\\omega C_{gd}(1 - g_{m1}R_S)}{1 + (\\omega C_{gd}R_S)^2}$$\n\n**For inductive behavior:** B < 0, which requires:\n\n$$\\boxed{g_{m1} \\cdot R_S > 1}$$\n\n## Intuitive Explanation\n\nWhen **Vout increases** at AC:\n1. Capacitive current flows through Cgd, making Vg more negative\n2. This reduces Vgs and therefore reduces drain current\n3. If gm₁·Rs > 1, the drain current reduction is **larger** than the capacitive current\n4. Net effect: current **lags** voltage → **inductive characteristic**\n\nThis negative feedback through Cgd and Rs essentially creates a frequency-dependent negative conductance that, combined with the capacitive element, manifests as an inductive impedance.",
        "format": "markdown",
        "sha256": "4ddc20e29b2cfd11200e06be4155682cc90bd117d5aefdd7c34270485f8dc665"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The stated condition gm₁Rₛ > 1 matches the correct inductive condition Rₛ > 1/gm₁, but the answer misidentifies the source follower as a common-source stage and attributes the effect to Cgd. The actual mechanism is Cgs coupling the gate and source, causing Zout to rise from about 1/gm₁ to Rₛ.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 6022,
        "total_tokens": 7648,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5487,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 6022,
        "total_tokens": 7648,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5487,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why the Output Impedance Can Be Inductive\n\nThis circuit is a **source-follower** (common-drain) configuration where M1's source drives the output, with M2 acting as a current-source load. The inductive behavior arises from the interaction between **Rs**, **Cgs** (gate-source capacitance), and the transconductance **gm**.\n\n## Small-Signal Analysis\n\nTo find the output impedance, apply a test voltage **vtest** at Vout with Vin = 0 (AC ground).\n\n### Step 1: Find the Gate Voltage\n\nAt M1's gate node, applying KCL:\n- Current through Rs: vg/Rs\n- Current through Cgd (gate to drain at AC ground): vg·sCgd  \n- Current through Cgs (gate to source at vtest): (vg - vtest)·sCgs\n\nThis gives:\n$$v_g = \\frac{v_{test} \\cdot sR_sC_{gs}}{1 + sR_s(C_{gs} + C_{gd})}$$\n\n### Step 2: Find Gate-Source Voltage\n\n$$v_{gs} = v_g - v_{test} = -v_{test}\\frac{1 + sR_sC_{gd}}{1 + sR_s(C_{gs} + C_{gd})}$$\n\n### Step 3: Output Admittance\n\nThe drain current is ids = gm·vgs, which flows into the output node. The output admittance becomes:\n\n$$Y_{out} \\approx g_m\\frac{1 + sR_sC_{gd}}{1 + sR_s(C_{gs} + C_{gd})}$$\n\nFor moderate frequencies, using first-order expansion:\n\n$$Y_{out} \\approx g_m(1 - sR_sC_{gs})$$\n\n### Step 4: Output Impedance\n\n$$Z_{out} = \\frac{1}{Y_{out}} \\approx \\frac{1}{g_m}(1 + sR_sC_{gs}) = \\frac{1}{g_m} + s\\frac{R_sC_{gs}}{g_m}$$\n\nThis is in the form **R + sL** where:\n- **R** = 1/gm\n- **Leff** = RsCgs/gm ← **Effective inductance!**\n\n## Physical Explanation\n\n1. When the output voltage changes, Cgs couples this change to the gate\n2. However, Rs prevents the gate voltage from instantly following the source voltage\n3. The RC time constant (RsCgs) creates a **phase lag** in vgs\n4. The drain current gm·vgs therefore **lags** the output voltage\n5. A lagging current relationship means **inductive behavior**\n\n## Conclusion\n\nThe output impedance appears inductive because Rs and Cgs create a feedback path that causes the transistor's current response to lag behind voltage changes at the output. The circuit acts as if it has an inductance of **Leff ≈ RsCgs/gm** in series with 1/gm resistance.",
        "format": "markdown",
        "sha256": "d8bee77c049783ce4b0d9ca3bdcb3641390a1eaf5aff0d52050a9baae798aa8b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the source follower and the relevant Rs–Cgs interaction, but its output-admittance derivation omits the Cgs current at the output. This gives the wrong inductance and predicts inductive behavior without the required Rs > 1/gm condition; it also misses the low- to high-frequency impedance transition.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 7718,
        "total_tokens": 9344,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6966,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 7718,
        "total_tokens": 9344,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6966,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why the Output Impedance Can Be Inductive\n\nThis circuit is a **common-source amplifier with source degeneration (RS) and active load (M2)**. The output impedance can exhibit inductive behavior due to the interaction between the **gate-drain capacitance (Cgd)** of M1, the **source resistor RS**, and the transistor's **transconductance (gm)**.\n\n## Physical Mechanism\n\n### 1. **Feedback Through Cgd and RS**\n\nWhen a small signal current is injected at the output (Vout):\n\n- **Capacitive coupling**: Current flows through Cgd from drain to gate\n- **Transconductance action**: The gate voltage change creates a drain current: $i_d = g_m v_{gs}$\n- **Source degeneration**: This current flows through RS, creating a voltage drop\n- **Negative feedback**: The voltage across RS reduces Vgs, which opposes the original change\n\n### 2. **Phase Reversal Creates Inductive Behavior**\n\nThe key is that this feedback mechanism creates a **phase relationship** where:\n\n```\n↑ Vout → current through Cgd → ↑ Vg → ↑ Id → ↑ Vs → ↓ Vgs → ↓ Id\n```\n\nThe net effect **opposes** the capacitive current, creating a \"negative capacitance\" effect that manifests as **inductance**.\n\n## Mathematical Expression\n\nThe output impedance can be approximated as:\n\n$$Z_{out} \\approx r_{ds1} \\parallel r_{ds2} \\cdot \\left[1 + s \\cdot C_{gd} \\cdot r_{ds} \\cdot g_m \\cdot R_S\\right]$$\n\nThe term $s \\cdot C_{gd} \\cdot r_{ds} \\cdot g_m \\cdot R_S$ represents an **effective inductance**:\n\n$$L_{eff} = C_{gd} \\cdot r_{ds} \\cdot g_m \\cdot R_S$$\n\n## Practical Significance\n\nThis inductive output impedance is useful for:\n- **Bandwidth extension** (inductive peaking)\n- **High-frequency compensation** in amplifiers\n- Becomes significant when $g_m R_S$ is substantial (strong source degeneration)",
        "format": "markdown",
        "sha256": "2ae3b8703528bb167cd267660a4ef6a4b78fbe6ece8c7b81bbaa230e4845d71f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source follower as a common-source stage and attributes the effect to Cgd and source degeneration. The actual mechanism is the gate-to-source capacitance shifting Zout from about 1/gm1 to RS, making it inductive when RS > 1/gm1.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 2100,
        "total_tokens": 3726,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1546,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1626,
        "output_tokens": 2100,
        "total_tokens": 3726,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1546,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Configuration\n\nThis circuit is a **current mirror with resistive load** (also functioning as a **current-to-voltage converter**).\n\n### Key Components:\n- **I_in**: Input current source\n- **M₂**: Diode-connected NMOS transistor (reference)\n- **M₁**: NMOS transistor (mirror output)\n- **R_D1**: Load resistor\n- **V_DD**: Supply voltage\n\n## Circuit Operation\n\n### 1. **Current Mirror Setup**\n- M₂ is configured as a diode-connected transistor (gate and drain connected at node X)\n- This forces M₂ into saturation with V_GS2 = V_DS2\n- The input current I_in flows through M₂, establishing the gate voltage at node X:\n\n$$V_X = V_{GS2} = V_{TH} + \\sqrt{\\frac{2I_{in}}{\\mu_n C_{ox}(W/L)_2}}$$\n\n### 2. **Current Mirroring**\n- M₁ has its gate connected to the same voltage (node X)\n- With V_GS1 = V_GS2, M₁ mirrors the reference current:\n\n$$I_{D1} = I_{in} \\times \\frac{(W/L)_1}{(W/L)_2}$$\n\n### 3. **Output Voltage**\nThe output voltage is determined by the voltage drop across R_D1:\n\n$$V_{out} = V_{DD} - I_{D1} \\cdot R_{D1} = V_{DD} - I_{in} \\cdot R_{D1} \\cdot \\frac{(W/L)_1}{(W/L)_2}$$\n\n## Key Characteristics\n\n**Function**: Current-to-voltage converter (transimpedance amplifier)\n\n**Transimpedance Gain**:\n$$Z_{trans} = \\frac{\\partial V_{out}}{\\partial I_{in}} = -R_{D1} \\cdot \\frac{(W/L)_1}{(W/L)_2}$$\n\n**Design Constraints**:\n- M₁ must remain in saturation: V_out ≥ V_X - V_TH\n- This limits the maximum value of I_in\n\n## Applications\n- Photodiode amplifiers\n- Sensor interfaces  \n- Current sensing circuits\n- Analog biasing circuits",
        "format": "markdown",
        "sha256": "a317eb5af32a1a087f2b287a700436a778115f288cda887fcf17573ab295d8db"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It places the input at X and M1's gate at X, but incorrectly treats M2 as diode-connected and the circuit as a current mirror. It misses the positive-feedback loop through M1 and M2, so the predicted linear transimpedance behavior is wrong.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 2154,
        "total_tokens": 3742,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1569,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 2154,
        "total_tokens": 3742,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1569,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Type\nThis is a **NMOS current mirror with resistive load** circuit.\n\n## Circuit Components\n- **M₁, M₂**: NMOS transistors\n- **M₂**: Diode-connected (gate and drain shorted at node X)\n- **M₁**: Output transistor\n- **I_in**: Input current source\n- **R_D1**: Load resistor\n- **V_DD**: Power supply\n\n## Circuit Operation\n\n### 1. **Reference Branch (M₂)**\n- Current I_in flows through diode-connected M₂\n- This establishes the gate voltage: **V_X = V_GS2**\n- M₂ operates in saturation by default (V_DS2 = V_GS2)\n- Current relationship: I_in = ½μₙC_ox(W/L)₂(V_GS2 - V_TH)²\n\n### 2. **Output Branch (M₁)**\n- M₁ has the same gate-source voltage as M₂: **V_GS1 = V_X = V_GS2**\n- The drain current I_D1 mirrors I_in:\n  - If (W/L)₁ = (W/L)₂, then **I_D1 = I_in**\n  - If (W/L)₁ = K(W/L)₂, then **I_D1 = K·I_in**\n\n### 3. **Output Voltage**\n$$V_{out} = V_{DD} - I_{D1} \\cdot R_{D1}$$\n\n## Key Characteristics\n\n- **Function**: Current mirror with current-to-voltage conversion\n- **Current mirroring ratio**: (W/L)₁/(W/L)₂\n- **Output impedance**: r_o1 || R_D1\n\n## Operating Conditions\n\nFor proper operation, M₁ must remain in saturation:\n$$V_{out} \\geq V_X - V_{TH}$$\n$$V_{DD} - I_{D1} \\cdot R_{D1} \\geq V_{GS2} - V_{TH}$$\n\n## Applications\n- Biasing circuits\n- Active loads in amplifiers\n- Precision current sources\n- Analog signal processing circuits",
        "format": "markdown",
        "sha256": "647ff5c4d21c398f24b4b5aab79ae01aa545883e87b17f54410ac31866446641"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It treats M₂ as diode-connected and misses the positive-feedback loop, so its current-mirror analysis is fundamentally wrong. It does identify M₁ as the output transistor controlled by node X and recognizes the input current source, warranting 1 rather than 0.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1666,
        "total_tokens": 3254,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1108,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1666,
        "total_tokens": 3254,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1108,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Current Mirror with Resistive Load\n\n## Circuit Configuration\n\nThis is a **current mirror circuit with resistive load**, consisting of:\n- Two NMOS transistors (M₁ and M₂)\n- Input current source (I_in)\n- Load resistor (R_D1)\n- Supply voltage (V_DD)\n\n## Operating Principle\n\n### 1. **Current Mirror Formation**\n- **M₁** is **diode-connected** (gate shorted to drain at node X)\n- Input current I_in flows through M₁, establishing voltage V_GS1 at node X\n- M₂'s gate connects to the same node X, so V_GS2 = V_GS1\n- Both transistors share the same gate voltage and have sources grounded\n\n### 2. **Current Copying Mechanism**\nFor matched transistors (same W/L ratios):\n- I_D1 = I_in (through M₁)\n- I_D2 ≈ I_in (through M₂)\n\n**The circuit \"mirrors\" the input current through M₂**\n\n### 3. **Output Voltage**\nThe mirrored current flows through R_D1:\n\n$$V_{out} = V_{DD} - I_{D2} \\times R_{D1} ≈ V_{DD} - I_{in} \\times R_{D1}$$\n\n## Key Characteristics\n\n**Functionality:**\n- Current-to-voltage converter\n- Provides controlled current source (M₂) biased by I_in\n- Linear relationship between input current and output voltage\n\n**Operating Constraints:**\n- M₁ saturation: Automatically satisfied (diode-connected)\n- M₂ saturation: V_out ≥ V_GS - V_th\n- Output range: (V_GS - V_th) ≤ V_out ≤ V_DD\n\n**Current Scaling:**\nIf (W/L)₂ = n·(W/L)₁, then I_D2 = n·I_in\n\n## Applications\n- Biasing circuits\n- Current sources for analog ICs\n- Active loads\n- Building block for op-amps and comparators",
        "format": "markdown",
        "sha256": "c5622db7774bdd6e3ac08dff8236390656aec93e54e84d715f5558abc9ace030"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the topology: M1 is not diode-connected, and M2's gate is tied to Vout, not node X. It therefore misses the positive-feedback loop and incorrectly describes a current mirror.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1635,
        "total_tokens": 3223,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1104,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1588,
        "output_tokens": 1635,
        "total_tokens": 3223,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1104,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Shunt-Feedback Transimpedance Amplifier\n\n## Circuit Topology\n\nThis is a **two-stage transimpedance amplifier** (current-to-voltage converter) with shunt feedback. Key components:\n\n- **Input**: Current source (Iin)\n- **Output**: Voltage (Vout)\n- **Transistors**: M1 and M2 (MOSFETs)\n- **Feedback**: Resistor RF providing shunt feedback\n- **Loads**: RD1, RD2\n\n## Circuit Operation\n\n### Signal Flow\n\n1. **Input Stage (M1)**:\n   - Input current Iin enters at the source of M1\n   - M1 appears to be diode-connected (gate tied to drain at Vb)\n   - Provides current-to-voltage conversion and biasing\n\n2. **Amplification Stage (M2)**:\n   - Common-source configuration with RD2 as load\n   - Gate driven by bias voltage at node X\n   - Provides voltage gain\n\n3. **Feedback Network (RF)**:\n   - Creates shunt feedback from output (Vout) to source of M1\n   - Current iRF = (Vout - Vs1)/RF\n   - Stabilizes gain and improves bandwidth\n\n### DC Biasing\n\n- RD1 establishes bias voltage at node X\n- This voltage biases both M1 and M2\n- Current through M1 sets the operating point\n- M2 operates in saturation region for amplification\n\n## Transfer Function\n\nThe **transimpedance gain** is:\n\n$$Z_T = \\frac{V_{out}}{I_{in}}$$\n\nWith high loop gain, the transimpedance is approximately:\n\n$$Z_T \\approx -R_F \\times A_{v}$$\n\nwhere Av is the voltage gain of the M2 stage.\n\n## Key Features\n\n✓ **Current-to-voltage conversion**  \n✓ **Negative feedback** improves linearity and stability  \n✓ **Wide bandwidth** due to shunt feedback  \n✓ **Low input impedance** (desirable for current sensing)\n\n## Applications\n\n- **Photodiode amplifiers** (photodetectors)\n- **Optical receivers**\n- **Current sensing circuits**\n- **Instrumentation amplifiers**",
        "format": "markdown",
        "sha256": "d5b5ce6b76127d55e5b15cbe324f67bb8e7147e6bc8c7fda2a5dda9d682e691a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes a shunt-feedback transimpedance amplifier and correctly places RF from Vout to M1’s source, but misidentifies M1 as diode-connected instead of common-gate and gives an incorrect high-loop-gain transimpedance of −RF·Av. These connection errors cap the score at 2.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 3589,
        "total_tokens": 5191,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3038,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 3589,
        "total_tokens": 5191,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3038,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Shunt-Shunt Feedback Transimpedance Amplifier\n\n## Circuit Type\nThis is a **transimpedance amplifier** (current-to-voltage converter) with **shunt-shunt negative feedback**. It converts an input current into an output voltage.\n\n## Circuit Components\n\n- **Iin**: Input current source\n- **M1, M2**: NMOS transistors (gates connected together at node X)\n- **RF**: Feedback resistor (from Vout to input node)\n- **RD1**: Gate bias resistor\n- **RD2**: Output load resistor\n- **VDD**: Power supply\n\n## Circuit Operation\n\n### 1. **DC Biasing**\n- RD1 biases node X (gates of both M1 and M2) from VDD\n- This establishes the DC operating point for both transistors\n- M2 operates as a common-source amplifier with source grounded\n\n### 2. **Signal Path**\n- Input current Iin flows into M1's source (input node)\n- M1 operates in **common-gate configuration** (gate at fixed DC bias)\n- M2 provides additional gain in **common-source configuration**\n- RF provides feedback from output (Vout) back to input\n\n### 3. **Feedback Mechanism**\nThe shunt-shunt feedback (RF) provides:\n- **Low input impedance** (virtual ground at input)\n- **Controlled transimpedance gain**\n- **Improved stability and bandwidth**\n- Feedback current: $i_{RF} = \\frac{V_{out}}{R_F}$\n\n## Key Performance Parameters\n\n### Transimpedance Gain\n$$Z_T = \\frac{V_{out}}{I_{in}} \\approx R_F \\text{ (for high loop gain)}$$\n\n### Input Impedance\n$$Z_{in} \\approx \\frac{R_F}{1 + A_{loop}}$$\nwhere $A_{loop}$ is the loop gain. With high loop gain, $Z_{in}$ is very low.\n\n### Bandwidth\nThe feedback network extends bandwidth:\n$$BW \\approx \\frac{GBW}{R_F \\cdot C_{in}}$$\nwhere GBW is the gain-bandwidth product and $C_{in}$ is input capacitance.\n\n## Applications\n\n- **Photodiode amplifiers** (optical receivers)\n- **Current measurement circuits**\n- **Sensor interfaces**\n- **Instrumentation amplifiers**\n\n## Advantages\n\n✓ Low input impedance (good for current sensing)  \n✓ Precise gain control via RF  \n✓ Good linearity  \n✓ Stable operation with negative feedback  \n✓ Wide bandwidth capability",
        "format": "markdown",
        "sha256": "1c2509a6a82b98d8cad25d1621394c1c7590c0aa30fc416b554cf38092fa17b3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the circuit as a shunt-shunt transimpedance amplifier and describes the feedback path and common-gate/common-source roles in its signal-path discussion. However, it also explicitly says both transistor gates are connected at X and that RD1 biases X, misreading the topology; this contradiction limits the score to 2.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 5943,
        "total_tokens": 7545,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5294,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 5943,
        "total_tokens": 7545,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5294,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Type: **Transimpedance Amplifier (TIA)**\n\nThis is a **current-to-voltage converter** with shunt-shunt feedback, commonly used in optical receivers and current sensing applications.\n\n## Circuit Topology\n\nThe circuit consists of two cascaded stages:\n\n1. **First Stage (M₁):** Common-gate amplifier\n   - Input: Current at source\n   - Load: R_D1\n   - Output: Node X (voltage)\n\n2. **Second Stage (M₂):** Common-source amplifier\n   - Input: Node X (gate)\n   - Load: R_D2\n   - Output: V_out\n\n3. **Feedback Network:** Resistor R_F providing negative feedback from output to input\n\n## Operating Principle\n\n1. Input current **I_in** enters the source of M₁\n2. M₁ converts current to voltage at node X (low input impedance)\n3. M₂ amplifies the voltage at X to produce **V_out**\n4. Feedback current **i_RF = V_out/R_F** flows back through R_F\n5. Net input current to M₁: **I_in - i_RF**\n\n## Key Performance Characteristics\n\n### Transimpedance Gain\n**Z_T = V_out/I_in ≈ -R_F** (for high loop gain)\n\n### Input Impedance\n**R_in ≈ R_F/(1+A)** where A is open-loop gain\n- Very low due to shunt feedback and common-gate configuration\n- Ideal for current sources (photodiodes)\n\n### Feedback Type\n**Shunt-Shunt** (current-sampling, current-mixing) negative feedback\n\n### Advantages\n- Low input impedance\n- Stable, predictable gain set by R_F\n- Extended bandwidth\n- Reduced distortion\n\n## Common Applications\n- Photodiode receivers (optical communication)\n- Transimpedance amplifiers\n- Current measurement circuits\n- RF front-ends",
        "format": "markdown",
        "sha256": "64a6f13be05891e2f65936c9838a0e4207ad0ed6340774108410a200a1b8973f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from Vout to the input, forming a transimpedance amplifier.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 1889,
        "total_tokens": 3491,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1407,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1602,
        "output_tokens": 1889,
        "total_tokens": 3491,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1407,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Regulated Cascode Current Source\n\n## Circuit Identification\n\nThis is a **regulated cascode** (also called **low-voltage cascode** or **gain-boosted cascode**) circuit. It's commonly used in analog IC design for current sources and current mirrors.\n\n## Circuit Components\n\n- **M₂** (PMOS): Main current source transistor\n- **M₁** (NMOS): Local feedback/regulation transistor  \n- **I₁**: Reference/load current\n- **I_in**: Input bias current source\n- **Additional current source** (downward): Part of biasing network\n- **V_b**: Bias voltage for M₁\n\n## Circuit Topology\n\n```\nVDD → M₂ (source-to-drain) → Vout\nVDD → I₁ → Vout\nVout → M₁ (drain-to-source) → Gate of M₂\n```\n\n## Operating Principle\n\n### 1. **Biasing**\n- The current sources at the bottom set the gate voltage of M₂\n- V_b biases M₁'s gate\n- I₁ establishes the reference current through M₂\n\n### 2. **Regulation Mechanism**\nThe local feedback loop provides impedance enhancement:\n\n- If **Vout increases** →\n  - V_DS of M₁ increases\n  - M₁ conducts more current\n  - Gate voltage of M₂ decreases\n  - M₂ provides more resistance to the change\n  - Net effect: very high output impedance\n\n### 3. **Key Advantages**\n\n✓ **High output impedance**: Much higher than simple current source  \n✓ **Low voltage headroom**: Less V_DS required than traditional cascode  \n✓ **Better PSRR**: Improved power supply rejection  \n✓ **Suitable for low-voltage applications**\n\n## Output Impedance\n\nThe output impedance is approximately:\n\n**r_out ≈ g_m1 · r_o1 · r_o2**\n\nwhere:\n- g_m1 = transconductance of M₁\n- r_o1, r_o2 = output resistances of M₁ and M₂\n\nThis is similar to a cascode but achieved with lower voltage overhead.\n\n## Applications\n\n- High-performance current mirrors\n- Active loads in op-amps\n- Bias circuits in low-voltage analog ICs\n- Any application requiring high output impedance current sources",
        "format": "markdown",
        "sha256": "b7f0381725477561c92405ebab58e0f4547d95a169b7719c6f536719c0fafaed"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misreads the circuit as a regulated-cascode current source and asserts high output impedance. The actual feedback runs from the input node through common-gate NMOS M1 to Vout and back through PMOS M2 to the input, giving very low input resistance and transimpedance/output resistance on the order of 1/gm2.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 2525,
        "total_tokens": 4085,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1939,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 2525,
        "total_tokens": 4085,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1939,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Topology\n\nThis circuit consists of:\n- **M₂** (PMOS transistor): Source connected to V_DD, drain to V_out, gate to node X\n- **M₁** (NMOS transistor): Drain connected to V_out, source to node X, gate to bias voltage V_b\n- **Current source I₁**: Connected between V_DD and V_out\n- **Current sources at node X**: I_in (sourcing current upward) and another sink current source\n- **Output**: V_out\n\n## Circuit Type\n\nThis is a **regulated current source** or **current buffer circuit** with complementary MOSFETs in a push-pull-like configuration.\n\n## Operating Principle\n\n### Node X (Bias Node):\n- The current sources establish a stable bias voltage V_X at node X\n- By KCL: $$I_{in} = I_{sink} + I_{M1}$$\n- This voltage controls M₂'s gate and provides M₁'s source connection\n\n### At V_out (Output Node):\n- $$I_{M2} + I_1 = I_{M1} + I_{load}$$\n- Both M₁ and M₂ contribute to output current capability\n\n### Transistor Operation:\n\n**M₂ (PMOS):** \n- Acts as a current source from V_DD\n- Current: $I_{M2} = \\frac{\\beta_2}{2}(V_{DD} - V_X - |V_{TP}|)^2$ (in saturation)\n\n**M₁ (NMOS):**\n- Provides a path to sink current\n- Current: $I_{M1} = \\frac{\\beta_1}{2}(V_b - V_X - V_{TN})^2$ (in saturation)\n\n## Key Features\n\n1. **High output impedance**: The current source configuration provides good output resistance\n2. **Programmable operation**: V_b controls M₁ behavior\n3. **Stable biasing**: Current sources at node X set operating point\n4. **Rail-to-rail capability**: Complementary transistors allow wider output swing\n\n## Applications\n\n- Current reference generation\n- Current-mode signal processing\n- Current mirror with improved accuracy\n- Voltage-to-current converter\n- Analog building block in current-mode circuits",
        "format": "markdown",
        "sha256": "a78394888fdd5a564ffd82c52ed7e6aeecd912e0470a77e84b83b44116a988c6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M1 as an NMOS and places its source at the input node and drain at Vout, but reverses M2’s gate and drain connections. It consequently misses the feedback loop and low input resistance, instead describing a push-pull current source with high output impedance.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 5470,
        "total_tokens": 7030,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4911,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 5470,
        "total_tokens": 7030,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4911,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\n## Circuit Topology\n\nThis circuit appears to be a **current-mode differential amplifier** or **current-steering circuit** with the following components:\n\n### Components:\n- **M₁, M₂**: NMOS transistors\n- **I₁**: Current source (active load)\n- **I_in**: Input current source\n- **V_DD**: Power supply\n- **V_b**: Bias voltage\n- **V_out**: Output voltage\n\n## Circuit Configuration\n\n```\n                V_DD\n                  |\n                 I₁ (load)\n                  |\n        +---------+---------+\n        |                   |\n     [M₂ D]             [M₁ D]\n        |                   |\n     [M₂ G]   node X    [M₁ G]--V_b\n        |       |            |\n     [M₂ S]-----+--------[M₁ S]\n                |\n           Current sources\n           (I_in + other)\n                |\n               GND\n```\n\n## Circuit Operation\n\n1. **M₂**: Appears to be diode-connected (gate connected to drain at V_out), acting as an active load or current mirror element\n\n2. **M₁**: Operates as a common-source amplifier with gate bias V_b\n\n3. **Current Sources at Bottom**: Provide bias currents and input signal current\n\n4. **I₁**: Active load providing high output impedance for voltage gain\n\n5. **Node X**: Common source node where both transistors meet\n\n## Likely Function\n\nThis circuit functions as:\n- **Current conveyor** or **wide-swing cascode** configuration\n- **Current-to-voltage converter** (I_in → V_out)\n- **Current mirror with regulated output**\n\n## Key Characteristics\n\n- **Input**: Current (I_in)\n- **Output**: Voltage (V_out)\n- **Gain**: Determined by I₁ current source impedance\n- **Bias**: V_b sets operating point of M₁\n- High output impedance due to current source load I₁",
        "format": "markdown",
        "sha256": "275c4fef30cf9f3de559fca38f72c24d75f4d87bd00f9239cf17bc3ed453bdb0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies both devices as NMOS and the topology, missing M1’s common-gate input role, M2’s feedback path, and the low-input-resistance/current-buffer behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 5246,
        "total_tokens": 6806,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4750,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1560,
        "output_tokens": 5246,
        "total_tokens": 6806,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4750,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Ring Oscillator with Large Capacitors\n\nLooking at this circuit, I can see it's a **three-stage ring oscillator** with inverters and load capacitors $C_L$ at each stage.\n\n## Does it fail to oscillate when $C_L \\to \\infty$?\n\n**Yes, the circuit fails to oscillate when the capacitors become arbitrarily large.**\n\nHere's why:\n\n### Oscillation Frequency\n\nThe oscillation frequency of a ring oscillator is approximately:\n\n$$f_{osc} \\approx \\frac{1}{2n\\tau_d}$$\n\nwhere $n = 3$ stages and $\\tau_d$ is the propagation delay per stage.\n\nThe delay through each stage is dominated by the RC time constant:\n$$\\tau_d \\propto R_{out} \\cdot C_L$$\n\nwhere $R_{out}$ is the output resistance of each inverter.\n\n### As $C_L \\to \\infty$:\n\n1. **Frequency approaches zero**: \n   $$f_{osc} = \\frac{1}{6R_{out}C_L} \\to 0$$\n\n2. **Period approaches infinity**: \n   $$T = \\frac{1}{f_{osc}} \\to \\infty$$\n\n3. **Voltage transitions become infinitely slow**: Since $\\frac{dV}{dt} = \\frac{I}{C_L}$, as $C_L \\to \\infty$, the voltage change rate approaches zero.\n\n### Physical Interpretation\n\n- The large capacitors essentially \"freeze\" the voltages at each node\n- The circuit cannot complete a cycle in any finite time\n- No periodic oscillation occurs—the circuit just sits in a quasi-static state\n\n### Conclusion\n\nWhile the circuit will oscillate at progressively lower frequencies for large but finite capacitances, in the limit as $C_L \\to \\infty$, the oscillation frequency goes to zero and the circuit **fails to oscillate**.",
        "format": "markdown",
        "sha256": "b9dfc0ae3ee55face13f55c8072c129e2738ce5848d63e8b9f6b8a42f45f9524"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that increasing capacitance lowers the frequency, but concludes that the ring fails to oscillate in the limit. The golden solution says the ring continues to oscillate at a lower frequency; this contrary conclusion earns at most 1.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 3765,
        "total_tokens": 5113,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3300,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 3765,
        "total_tokens": 5113,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3300,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Ring Oscillator with Large Capacitors\n\nLooking at this circuit, I can see it's a **three-stage ring oscillator** - three inverters connected in a feedback loop with load capacitors $C_L$ at each stage.\n\n## Will it fail to oscillate as $C_L → ∞$?\n\n**Yes, the circuit will fail to oscillate when the capacitors become arbitrarily large.**\n\nHere's why:\n\n### Oscillation Frequency Dependence\n\nThe oscillation frequency of a ring oscillator is approximately:\n\n$$f_{osc} \\approx \\frac{1}{2N\\tau}$$\n\nwhere:\n- $N = 3$ (number of stages)\n- $\\tau = R_{out} \\cdot C_L$ (delay per stage)\n- $R_{out}$ is the output resistance of each inverter\n\nAs $C_L$ increases:\n$$\\tau \\propto C_L \\implies f_{osc} \\propto \\frac{1}{C_L}$$\n\nTherefore: **$C_L → ∞$ means $f_{osc} → 0$**\n\n### Physical Interpretation\n\nWhen capacitors become arbitrarily large:\n\n1. **Voltage change rate**: From $I = C\\frac{dV}{dt}$, for finite output current and $C → ∞$:\n   $$\\frac{dV}{dt} → 0$$\n\n2. **Time constant**: Each node has $\\tau = RC_L → ∞$, meaning voltages are essentially \"frozen\"\n\n3. **Practical result**: The circuit cannot switch between logic states in any reasonable timeframe\n\n### Conclusion\n\nThe oscillation period $T = 1/f_{osc}$ approaches infinity, which is equivalent to no oscillation. The circuit becomes unable to change state, effectively failing to oscillate.",
        "format": "markdown",
        "sha256": "b856bea8f2ea3cb71b3feec2e9bb53ef10387cadd2e84824d3901a5dd78fff29"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that frequency decreases roughly as 1/C_L, but wrongly concludes that the ring stops oscillating. The oscillation condition remains satisfied; the circuit continues oscillating at a lower frequency.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 1862,
        "total_tokens": 3210,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1426,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 1862,
        "total_tokens": 3210,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1426,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this three-stage ring oscillator with load capacitors C_L, I need to analyze what happens as C_L → ∞.\n\n## Oscillation Condition Analysis\n\nFor a ring oscillator to oscillate, the Barkhausen criterion must be satisfied:\n- Loop gain magnitude = 1\n- Total phase shift around loop = 360° (or 0° mod 360°)\n\n### Phase Shift Components\n\n1. **Three inverters**: Each provides 180° phase shift\n   - Total from inverters: 3 × 180° = 540° ≡ 180° (mod 360°)\n\n2. **Three RC stages**: Each has phase shift of −arctan(ωR₀C_L)\n   - Total from RC stages: −3·arctan(ωR₀C_L)\n\n### Finding Oscillation Frequency\n\nFor oscillation, total phase shift must equal 0° (mod 360°):\n\n180° − 3·arctan(ωR₀C_L) = 0°\n\nThis gives:\n- arctan(ωR₀C_L) = 60°\n- ωR₀C_L = √3\n- **ω₀ = √3/(R₀C_L)**\n\n## What Happens as C_L → ∞?\n\nAs the capacitors become arbitrarily large:\n\n$$\\omega_0 = \\frac{\\sqrt{3}}{R_0 C_L} \\to 0$$\n\nAt ω = 0 (DC):\n- Phase shift from RC stages: −3·arctan(0) = 0°\n- Total phase shift: 180° + 0° = 180°\n- Required phase shift: 0° or 360°\n\n**The phase condition is NOT satisfied at DC!**\n\n## Physical Interpretation\n\nWith infinite capacitance:\n- Any voltage change requires Q = CV → ∞ charge\n- With finite inverter current drive, dV/dt → 0\n- The circuit cannot change state in finite time\n- The nodes are effectively \"frozen\"\n\n## Answer\n\n**YES, the circuit fails to oscillate** when the capacitors become arbitrarily large. \n\nWhile the circuit oscillates at lower and lower frequencies as C_L increases, in the limit C_L → ∞, the oscillation frequency approaches zero and the Barkhausen phase criterion can no longer be satisfied. The circuit effectively becomes unable to change state in finite time.",
        "format": "markdown",
        "sha256": "d879c5b5c09c78a5c2ad3ccda5d5b17ddd40ddb07974ade66573aa73a4f8cd7e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly recognizes that increasing all three capacitors lowers the oscillation frequency roughly as 1/C_L, but incorrectly concludes that the ring fails to oscillate in the large-capacitance limit. The golden solution identifies continued oscillation at a lower frequency as the central result.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 6565,
        "total_tokens": 7913,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5990,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1348,
        "output_tokens": 6565,
        "total_tokens": 7913,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5990,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Phase Noise with Doubled Capacitors\n\nThis is a **3-stage ring oscillator**. When the capacitors CL are doubled, the phase noise **improves (decreases)**.\n\n## Key Effects:\n\n### 1. **Frequency Change**\n- Oscillation frequency: $f_0 \\propto \\frac{1}{C_L}$\n- Doubling CL **halves the oscillation frequency**\n\n### 2. **Phase Noise Improvement**\n\nPhase noise approximately follows:\n\n$$\\mathcal{L}(\\Delta f) \\propto \\frac{1}{q_{max}^2} \\propto \\frac{1}{C_L^2}$$\n\nwhere $q_{max}$ is the maximum charge swing (∝ CL·V).\n\n**Result**: Doubling CL reduces phase noise by approximately **6 dB** (factor of 4).\n\n## Physical Explanation:\n\n- **More energy storage**: Larger capacitors store more charge/energy\n- **Reduced noise sensitivity**: More charge is required to cause a given voltage/phase change\n- **Harder for noise to disturb oscillation**: Thermal noise currents have less relative impact on phase when integrated onto larger capacitors\n\n## Trade-off:\n\n✅ **Better phase noise** (lower $\\mathcal{L}(\\Delta f)$)  \n⚠️ **Lower oscillation frequency** (f₀ halved)  \n⚠️ **Larger circuit area** (bigger capacitors)\n\nThis is a common design trade-off in oscillators: increasing capacitance improves phase noise performance at the cost of reduced frequency and increased size.",
        "format": "markdown",
        "sha256": "28a232a3392da82445fa93abfd8694b0799dc3d74953818f644291c4438d8f15"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and lowers phase noise by about a factor of four (6 dB), with a supporting charge/noise-sensitivity explanation.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 1860,
        "total_tokens": 3204,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1469,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 1860,
        "total_tokens": 3204,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1469,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **3-stage ring oscillator** circuit, I need to analyze how doubling the load capacitances (CL) affects the phase noise.\n\n## Key Effects of Doubling Capacitance\n\n**1. Oscillation Frequency Change:**\n- Ring oscillator frequency: f₀ = 1/(2N·τd) where N=3 stages\n- Stage delay: τd ≈ R·CL \n- When CL → 2CL: **f₀ → f₀/2** (frequency halves)\n\n**2. Phase Noise Relationship:**\n\nFor a ring oscillator, phase noise at offset frequency Δf follows:\n\n$$L(\\Delta f) \\propto \\frac{1}{q_{max}^2} \\cdot \\left(\\frac{f_0}{\\Delta f}\\right)^2$$\n\nwhere qmax = CL·V is the maximum charge swing.\n\n**Impact of changes:**\n- Charge storage: qmax → 2qmax, so 1/q²max → **1/4**\n- Frequency term: (f₀/Δf)² → (f₀/2/Δf)² = **(f₀/Δf)²/4**\n\n**Combined effect:**\n$$L_{new} = L_{old} \\times \\frac{1}{4} \\times \\frac{1}{4} = \\frac{L_{old}}{16}$$\n\n## Answer\n\n**Phase noise improves (decreases) by 12 dB**\n\nThis makes physical sense:\n- Larger capacitance → more charge storage → less sensitivity to noise charges (6 dB improvement)\n- Lower oscillation frequency → better noise averaging (additional 6 dB improvement)  \n- Total: **12 dB reduction in phase noise**\n\nThis assumes comparison at the same absolute offset frequency Δf from each carrier.",
        "format": "markdown",
        "sha256": "f8dac681d527f1e0a812569d8b3f4a0f6b466d4d006b58309b7b902753ef14f9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly predicts that doubling the capacitors halves the oscillation frequency and that phase noise decreases at a fixed absolute offset. But it double-counts the capacitance effect: the correct reduction is about 4× (6 dB), not 16× (12 dB).",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 8343,
        "total_tokens": 9687,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7895,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 8343,
        "total_tokens": 9687,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7895,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Phase Noise Analysis When Capacitors are Doubled\n\nThis is a **3-stage ring oscillator**. When the three capacitors (C_L) are doubled, the **phase noise decreases by 3 dB** (improves by a factor of 2).\n\n## Why This Happens:\n\n### 1. **Oscillation Frequency Changes**\n- The oscillation frequency: $f_0 \\propto \\frac{1}{C_L}$\n- When $C_L$ doubles → $f_0$ **halves**\n\n### 2. **Timing Jitter Analysis**\nFor each stage:\n- Voltage noise on capacitor: $v_n = \\sqrt{\\frac{kT}{C_L}}$ (thermal noise)\n- Slew rate during switching: $S = \\frac{I}{C_L}$\n- Timing uncertainty: $\\sigma_t = \\frac{v_n}{S} = \\frac{\\sqrt{kT/C_L}}{I/C_L} \\propto \\sqrt{C_L}$\n\n### 3. **Phase Jitter Calculation**\n- Phase is related to time by: $\\phi = 2\\pi f_0 t$\n- Phase jitter: $\\sigma_\\phi = 2\\pi f_0 \\cdot \\sigma_t \\propto \\frac{1}{C_L} \\cdot \\sqrt{C_L} = \\frac{1}{\\sqrt{C_L}}$\n\n### 4. **Phase Noise Result**\n- Phase noise spectral density: $\\mathcal{L}(\\Delta f) \\propto (\\sigma_\\phi)^2 \\propto \\frac{1}{C_L}$\n\n## Summary:\n**When all capacitors double:**\n- ✓ Oscillation frequency decreases by 2× (halves)\n- ✓ **Phase noise improves by 3 dB** (reduces by factor of 2)\n- ✓ Physical reason: Larger capacitors store more energy, making the oscillator less sensitive to noise perturbations",
        "format": "markdown",
        "sha256": "88f59c6899b19ede52a6ab33fd2053011afad609f7649f382479373e48336837"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies that doubling the capacitors halves the oscillation frequency and that phase noise decreases, but gives the wrong magnitude: at a fixed offset it should fall by about 6 dB (a factor of four), not 3 dB.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 4587,
        "total_tokens": 5931,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4083,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1344,
        "output_tokens": 4587,
        "total_tokens": 5931,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4083,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this ring oscillator circuit with 3 inverters and a load capacitor CL, I need to analyze whether it can sustain oscillation as CL → ∞.\n\n## Oscillation Conditions\n\nFor sustained oscillation, the **Barkhausen criteria** must be satisfied:\n1. **Loop gain** |H(jω)| ≥ 1  \n2. **Phase shift** around the loop = 360° (or 0°)\n\n## Analysis as CL → ∞\n\n**Effect on frequency:**\nThe capacitor CL creates a dominant pole at ω₁ = 1/(R·CL) where R is the output resistance of the first inverter. As CL increases, ω₁ → 0.\n\n**Phase Condition:**\nFor 3 inverters, the total phase shift is:\n∠H(jω) = 540° - [tan⁻¹(ω/ω₁) + tan⁻¹(ω/ω₂) + tan⁻¹(ω/ω₃)]\n\nFor oscillation, we need this to equal 360°, which requires:\ntan⁻¹(ω/ω₁) + tan⁻¹(ω/ω₂) + tan⁻¹(ω/ω₃) = 180°\n\nWhen ω₁ → 0 and ωosc >> ω₁:\n- tan⁻¹(ωosc/ω₁) ≈ 90°\n- The remaining phase must come from the other stages\n- This sets ωosc at a frequency determined by ω₂ and ω₃\n\n**Gain Condition (the critical issue):**\nAt the oscillation frequency ωosc, the loop gain magnitude is:\n\n|H(jωosc)| = A₀³/[√(1+(ωosc/ω₁)²) · √(1+(ωosc/ω₂)²) · √(1+(ωosc/ω₃)²)]\n\nWhen ωosc >> ω₁:\n|H(jωosc)| ≈ A₀³ · ω₁/ωosc · [...]\n\nAs ω₁ → 0, the loop gain → 0, falling below the minimum value of 1 needed for oscillation.\n\n## Conclusion\n\n**Yes, the circuit DOES fail to oscillate when CL becomes arbitrarily large.**\n\nThe large capacitor creates a severe low-pass filter at the first stage. While the phase condition can still be met at some frequency (determined by the other stages), the loop gain at that frequency becomes insufficient because the signal is heavily attenuated by the dominant pole created by CL. Without adequate loop gain, oscillation cannot be sustained.",
        "format": "markdown",
        "sha256": "aa074391dc1d9fa9fe88e808ce18585a985628f20e02c763eb144a029a2faa24"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large CL can stop oscillation and explains that its dominant pole drives loop gain below unity at the phase condition. The approximate pole and phase analysis supports the essential result.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 10150,
        "total_tokens": 11496,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9471,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 10150,
        "total_tokens": 11496,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9471,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Answer: No, the circuit does not fail to oscillate\n\n## Analysis:\n\nThis is a **3-stage ring oscillator** with a load capacitor CL at the first stage output.\n\n### Why oscillation continues even with large CL:\n\n1. **Loop Gain at DC**: Each inverter maintains high DC gain (typically >>1). The product of three inverter gains is still much greater than 1, satisfying the Barkhausen criterion for oscillation.\n\n2. **Phase Condition**: The odd number of inverters (3) provides the necessary 180° phase shift for oscillation, regardless of CL value.\n\n3. **Capacitor Behavior**: \n   - CL acts as a low-pass filter at the first stage\n   - As CL increases, the pole frequency ωp = 1/(RoCL) decreases (Ro = inverter output resistance)\n   - This slows down transitions but doesn't prevent them\n\n4. **Effect of Increasing CL**:\n   - Oscillation frequency: **f_osc ∝ 1/CL** (for large CL)\n   - As CL → ∞, frequency f → 0\n   - But oscillation doesn't stop; it just becomes slower\n\n### Practical Consideration:\nWith extremely large CL, the oscillation frequency becomes so low that:\n- Leakage currents may dominate\n- The period may exceed practical observation times\n- But **theoretically**, oscillation persists\n\n**Conclusion**: The circuit continues to oscillate at all CL values, with frequency inversely proportional to CL.",
        "format": "markdown",
        "sha256": "c9e57328f1acee390b7b380201e94fce209e78454c849715c4ac2e4c977eb4ba"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The conclusion is opposite the essential result: a sufficiently large one-sided load can make the loop fail to oscillate. The answer notes the falling pole frequency and slower transitions, but wrongly assumes oscillation persists and misapplies the inverter phase and DC-gain arguments to the loop condition.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 1372,
        "total_tokens": 2718,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1003,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 1372,
        "total_tokens": 2718,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1003,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis: Ring Oscillator with Load Capacitor\n\nLooking at this circuit, I can see it's a **3-stage ring oscillator** with a load capacitor CL at the first stage's output.\n\n## Will it fail to oscillate as CL → ∞?\n\n**YES**, the circuit will fail to oscillate when CL becomes arbitrarily large.\n\n## Reasoning:\n\n### 1. **RC Time Constant Effect**\n- The capacitor CL forms an RC circuit with the output resistance of the first inverter\n- Time constant: τ = R·CL\n- As CL → ∞, then τ → ∞\n\n### 2. **Signal Propagation Breakdown**\n- The first inverter must charge/discharge CL through its finite output resistance\n- With arbitrarily large CL:\n  - The voltage at that node changes infinitesimally slowly\n  - The node essentially becomes \"frozen\" at some DC voltage\n  - The AC signal cannot propagate through the loop\n\n### 3. **Oscillation Frequency**\nThe oscillation frequency is roughly:\n$$f_{osc} ≈ \\frac{1}{2πRC_L \\cdot 3}$$\n\nAs CL → ∞:\n- f_{osc} → 0\n- The period approaches infinity\n- Practically, this means **no oscillation**\n\n### 4. **Practical Reality**\nWhile mathematically you might argue the frequency approaches zero (infinitely slow oscillation), in practice:\n- No measurable oscillation occurs\n- The feedback loop is effectively broken\n- The circuit settles to a DC state\n\n**Conclusion**: The circuit requires a finite, reasonable CL to oscillate. An arbitrarily large CL prevents oscillation.",
        "format": "markdown",
        "sha256": "69e7130e4969b797133f22817203eaf484758173842e6b0e0e8c041b175599af"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that an arbitrarily large load on one node can stop oscillation and explains that the node becomes extremely slow, allowing the circuit to settle near DC. This is the accepted time-domain explanation; the rough frequency estimate is secondary.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 1063,
        "total_tokens": 2409,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 656,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1346,
        "output_tokens": 1063,
        "total_tokens": 2409,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 656,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **three-stage ring oscillator**, let me analyze what happens to phase noise when we double all the transistor widths.\n\n## Key Effects of Doubling Width (W)\n\nWhen W doubles (assuming reasonable biasing):\n\n1. **Capacitance**: C ∝ W, so **C → 2C**\n   - Gate capacitances (Cgs, Cgd) double\n   - Diffusion capacitances (Cdb, Csb) double\n\n2. **Transconductance**: gm ∝ W (for constant current density), so **gm → 2gm**\n   - Noise current: i²n = 4kTγgm also doubles\n\n3. **Oscillation Frequency**: f₀ ∝ I/(C·Vswing)\n   - If current scales with W: I → 2I and C → 2C\n   - Frequency stays **approximately constant**\n\n## Phase Noise Analysis\n\nFor ring oscillators, phase noise in the thermal noise region is:\n\n$$L(\\Delta\\omega) \\propto \\frac{kT \\cdot g_m}{C^2 \\cdot V^2_{swing}} \\cdot \\left(\\frac{\\omega_0}{\\Delta\\omega}\\right)^2$$\n\nWhen W doubles:\n- Numerator: gm → 2gm (doubles)\n- Denominator: C² → (2C)² = 4C² (quadruples)\n- Vswing remains approximately constant (supply-limited)\n\nTherefore:\n$$L(\\Delta\\omega) \\to \\frac{2g_m}{4C^2 \\cdot V^2} = \\frac{1}{2} L(\\Delta\\omega)$$\n\n## Result\n\n**Phase noise improves (decreases) by 3 dB**\n\nThe phase noise reduces to half its original value because while noise current doubles, the stored charge (and timing reference) quadruples. The increased capacitance provides better noise filtering relative to the signal.\n\n**Note**: This improvement comes at the cost of increased power consumption and chip area.",
        "format": "markdown",
        "sha256": "3cbfa86b917fa20a6be45b55fc30e7f5e7100bffe80f1d8bea22ff90bb94aab2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The answer gives the correct approximately 3 dB reduction and correctly notes that device noise current and capacitance scale up. However, it incorrectly says the stored charge quadruples; with unchanged swing, charge doubles. That flawed mechanism warrants 3 rather than full credit.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 5961,
        "total_tokens": 7577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5465,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 5961,
        "total_tokens": 7577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5465,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **3-stage ring oscillator**, let me analyze what happens to phase noise when we double the device widths.\n\n## Key Effects of Doubling Width (W)\n\nWhen W is doubled:\n\n1. **Transconductance**: gₘ ∝ W → doubles\n2. **Capacitances**: C_gs, C_gd, C_db all ∝ W → double  \n3. **Noise current**: i²ₙ ∝ 4kTγgₘ → doubles\n4. **Oscillation frequency**: f₀ ∝ gₘ/C → stays approximately constant\n\n## Phase Noise Analysis\n\nUsing the relationship between timing jitter and phase noise:\n\n**Noise Voltage:**\n- Noise current PSD: Sᵢ ∝ W (doubles)\n- Output impedance at node: Z ∝ 1/ωC\n- Noise voltage PSD: Sᵥ ∝ Sᵢ/C² ∝ W/W² = 1/W\n- RMS noise voltage: σᵥ ∝ 1/√W (reduces by √2)\n\n**Slew Rate:**\n- Current: I ∝ W (doubles)\n- Capacitance: C ∝ W (doubles)  \n- Slew rate: dV/dt = I/C → stays constant\n\n**Timing Jitter:**\n- σₜ = σᵥ/(dV/dt) ∝ 1/√W (reduces by √2)\n\n**Phase Noise:**\n- ℒ(Δω) ∝ σₜ² ∝ 1/W\n\n## Result\n\n**Phase noise decreases by 3 dB (factor of 2 improvement)**\n\nAdditionally:\n- **Flicker noise** (1/f) improves even more since it's proportional to 1/(WL)\n- At close-in offset frequencies, the improvement can exceed 3 dB\n- At higher offsets (thermal noise dominated), the improvement is 3 dB\n\n**Summary:** Doubling the device widths **improves** (reduces) the phase noise, primarily due to increased charge storage (larger C·V swing) while maintaining similar slew rate, resulting in better signal-to-noise ratio.",
        "format": "markdown",
        "sha256": "ea151eaf6c6a4359fa84aec410a135acb22f00613fed77c5a82f6a555a55487c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "The answer gives the expected 3 dB reduction and a sound scaling argument: noise-current PSD and node capacitance both double, so node-noise PSD halves while frequency and slew rate stay roughly constant. The added flicker-noise caveat is not needed for the central result.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 4152,
        "total_tokens": 5768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3589,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 4152,
        "total_tokens": 5768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3589,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **3-stage ring oscillator**, let's analyze what happens when we double all device widths.\n\n## Key Effects of Doubling Width (W):\n\n### 1. **Capacitance doubles** (∝ W)\n   - Gate capacitances: Cgs, Cgd ∝ W\n   - Junction capacitances: Cdb, Csb ∝ W\n\n### 2. **Current doubles** (∝ W)\n   - ID ∝ (W/L) for same VGS\n\n### 3. **Transconductance doubles** (∝ W)\n   - gm ∝ W\n\n### 4. **Frequency stays approximately constant**\n   - Delay per stage: τd ≈ (CL·ΔV)/ID\n   - Since both CL and ID double: τd ≈ (2CL·ΔV)/(2ID) = constant\n   - f₀ = 1/(2N·τd) remains roughly the same\n\n## Phase Noise Analysis:\n\nFor a ring oscillator, phase noise follows:\n\n$$L(\\Delta\\omega) \\propto \\frac{kT}{q_{max}^2} \\cdot \\left(\\frac{f_0}{\\Delta\\omega}\\right)^2$$\n\nor equivalently:\n\n$$L(\\Delta\\omega) \\propto \\frac{1}{C \\cdot V_{swing}^2}$$\n\nWhen W doubles:\n- **Charge swing**: qmax = C·Vswing **doubles** (C doubles, Vswing constant)\n- **Thermal noise current**: 4kTγgm **doubles**\n- **But**: Noise-to-phase coupling ∝ 1/qmax² **decreases by 4×**\n\n**Result: Phase noise improves (decreases) by 3 dB**\n\nThe larger capacitance provides better noise filtering and larger stored energy, which improves the oscillator's resilience to thermal noise, at the cost of doubled power consumption.",
        "format": "markdown",
        "sha256": "aabc831c631d6e1aefb68e55b4dc708213f90a1ea7aa2de87d3f8499cb44ec45"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that doubling all device widths reduces phase noise by about 3 dB. Its scaling discussion is consistent with the result: charge swing doubles while device noise current power also increases, yielding a twofold reduction in noise-to-signal ratio.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 3469,
        "total_tokens": 5085,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2981,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 3469,
        "total_tokens": 5085,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2981,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this ring oscillator circuit, I need to find the small-signal resistance looking into the common supply node where all three inverters connect.\n\n## Analysis Approach\n\nWhen analyzing the supply node impedance, I'll consider how a small perturbation in $V_{DD}$ affects the total current drawn from the supply.\n\n## Small-Signal Model\n\nEach inverter contains a PMOS transistor with its source connected to $V_{DD}$. For small-signal analysis:\n\nFor each PMOS transistor, using the small-signal model:\n$$i_d = g_m v_{sg} + \\frac{v_{sd}}{r_o}$$\n\nwhere:\n- $v_{sg}$ is the AC small-signal source-to-gate voltage  \n- $v_{sd}$ is the AC small-signal source-to-drain voltage\n- $g_m$ is the transconductance\n- $r_o$ is the output resistance\n\n## Current Response to Supply Perturbation\n\nWhen the supply voltage is perturbed by $\\Delta V_{DD}$:\n- The source voltage of each PMOS changes by $\\Delta v_s = \\Delta V_{DD}$\n- Assuming the gates and drains change more slowly (first-order analysis):\n\n$$\\Delta i_d = g_m \\Delta v_{sg} + \\frac{\\Delta v_{sd}}{r_o} \\approx \\left(g_m + \\frac{1}{r_o}\\right) \\Delta V_{DD}$$\n\nSince typically $g_m r_o \\gg 1$, this simplifies to:\n$$\\Delta i_d \\approx g_m \\Delta V_{DD}$$\n\n## Total Supply Current\n\nWith three identical inverter stages, all PMOS sources are connected in parallel to the supply node:\n\n$$\\Delta I_{DD} = 3 \\times \\Delta i_d = 3g_m \\Delta V_{DD}$$\n\n## Small-Signal Resistance\n\nThe small-signal resistance is:\n\n$$R_{in} = \\frac{\\Delta V_{DD}}{\\Delta I_{DD}} = \\frac{\\Delta V_{DD}}{3g_m \\Delta V_{DD}}$$\n\n$$\\boxed{R_{in} = \\frac{1}{3g_m}}$$\n\nwhere $g_m$ is the transconductance of the PMOS transistor in each inverter stage.\n\n**Note**: This is the first-order result. More precisely, the resistance could be expressed as $\\frac{1}{3(g_m + 1/r_o)}$, but since $g_m \\gg 1/r_o$ in typical designs, the dominant term is $\\frac{1}{3g_m}$.",
        "format": "markdown",
        "sha256": "fbb917c9fe562a3d834d04d95877406eb08cc9a46bafaaae9bb07bfcdad6d3cc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based resistance and ignores the oscillation-driven charging and discharging of the load capacitances, which sets the supply resistance here. Its stated 1/(3gm) therefore misses the dominant mechanism.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 10457,
        "total_tokens": 12068,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9814,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 10457,
        "total_tokens": 12068,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9814,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this 3-stage ring oscillator, I need to find the small-signal resistance looking into the common supply node that connects to all three inverters.\n\n## Small-Signal Analysis Approach\n\nFor each CMOS inverter stage, I'll consider the PMOS transistor connected to the supply node. When perturbing the supply voltage by a small amount $v_{dd}$, each PMOS contributes current:\n\n$$i_k = g_{m,p}(v_{dd} - v_{in,k}) + g_{ds,p}(v_{dd} - v_{out,k})$$\n\nwhere $g_{m,p}$ is the PMOS transconductance and $g_{ds,p} = 1/r_{o,p}$ is the output conductance.\n\n## Accounting for Feedback\n\nFor the ring oscillator, each stage has gain $-A$ and supply sensitivity $\\alpha$:\n$$v_{out,k} = -A \\cdot v_{in,k} + \\alpha \\cdot v_{dd}$$\n\nSumming around the ring (with $v_{in,k} = v_{out,k-1}$):\n$$\\sum_{k=1}^{3} v_{out,k} = \\frac{3\\alpha}{1+A} v_{dd}$$\n\n## Total Current from Supply\n\nThe total small-signal current is:\n$$i_{total} = \\sum_{k=1}^{3} i_k = 3(g_{m,p} + g_{ds,p})\\left(1 - \\frac{\\alpha}{1+A}\\right)v_{dd}$$\n\n$$= 3(g_{m,p} + g_{ds,p})\\frac{1+A-\\alpha}{1+A} v_{dd}$$\n\n## Input Resistance\n\n$$R_{in} = \\frac{v_{dd}}{i_{total}} = \\frac{1+A}{3(1+A-\\alpha)(g_{m,p} + g_{ds,p})}$$\n\nSince $g_{m,p} \\gg g_{ds,p}$ and for large loop gain $A \\gg \\alpha$:\n\n$$R_{in} \\approx \\frac{1}{3(1-\\alpha/A) \\cdot g_{m,p}} \\approx \\frac{1}{3g_{m,p}}$$\n\n## Final Answer\n\n$$\\boxed{R_{in} = \\frac{1}{3g_m}}$$\n\nwhere $g_m$ is the transconductance of the PMOS transistor in each inverter stage.\n\nThis result makes physical sense: from the supply node perspective, we see three PMOS source terminals in parallel (through the feedback loop), each presenting an effective resistance of $1/g_m$, giving a parallel combination of $1/(3g_m)$.",
        "format": "markdown",
        "sha256": "eb122bbb7c585476a197bd46fb8e4ed1781e34793cc979a48161bce3eba113dd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The static small-signal derivation is internally consistent, but it ignores the oscillator-driven charging and discharging of the load capacitances. The resulting gm-based resistance misses the dominant mechanism and the expected dependence on frequency and capacitance.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 10950,
        "total_tokens": 12561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10274,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 10950,
        "total_tokens": 12561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10274,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this 3-stage ring oscillator, I need to find the small-signal resistance at the common supply node (where all three inverters connect).\n\n## Setting Up the Small-Signal Analysis\n\nFor each CMOS inverter, the current drawn from the supply node is:\n\n$$i_{supply,k} = g_{m,p}(v_{dd} - v_{in,k}) + g_{ds,p}(v_{dd} - v_{out,k})$$\n\nwhere:\n- $g_{m,p}$ is the PMOS transconductance\n- $v_{dd}$ is the small-signal supply perturbation\n- $v_{in,k}$ and $v_{out,k}$ are the small-signal input and output voltages\n\n## Relating Output to Input\n\nFor each inverter stage with gain magnitude $A$ and high output resistance:\n\n$$v_{out,k} = -A \\cdot v_{in,k} + v_{dd}$$\n\nSubstituting this into the current expression and simplifying (using $A \\cdot g_{ds,p} \\approx g_m = g_{m,p} + g_{m,n}$):\n\n$$i_{supply,k} \\approx g_{m,p} v_{dd} + g_{m,n} v_{in,k}$$\n\n## Total Supply Current\n\nFor all three stages:\n\n$$i_{total} = \\sum_{k=1}^{3} i_{supply,k} = 3g_{m,p} v_{dd} + g_{m,n} \\sum_{k=1}^{3} v_{in,k}$$\n\n## Finding the Input Sum\n\nFrom the ring oscillator equations with feedback:\n\n$$\\sum_{k=1}^{3} v_{in,k} = \\frac{3v_{dd}}{1+A}$$\n\nThis comes from solving the common-mode response of the three coupled stages.\n\n## Final Result\n\nSubstituting back:\n\n$$i_{total} = 3g_{m,p} v_{dd} + g_{m,n} \\frac{3v_{dd}}{1+A} = 3v_{dd}\\left(g_{m,p} + \\frac{g_{m,n}}{1+A}\\right)$$\n\nFor typical CMOS inverters with high gain ($A >> 1$):\n\n$$i_{total} \\approx 3g_{m,p} v_{dd}$$\n\nTherefore, the small-signal resistance is:\n\n$$\\boxed{R_{in} = \\frac{v_{dd}}{i_{total}} = \\frac{1}{3g_{m,p}}}$$\n\nwhere $g_{m,p}$ is the transconductance of the PMOS transistor in each inverter.\n\n**Alternative form:** If expressed in terms of the total inverter transconductance $g_m = g_{m,p} + g_{m,n}$, and assuming symmetric design where $g_{m,p} \\approx g_{m,n}$:\n\n$$R_{in} \\approx \\frac{2}{3g_m}$$",
        "format": "markdown",
        "sha256": "1f58274ca90730a913a3776dbaf68dbdd047ac849d3460acaceaba7fb1fcb3cf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based supply resistance and misses the dominant oscillation-driven charging and discharging of the three load capacitances. The golden solution explicitly assigns such static gm-based answers a score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 13532,
        "total_tokens": 15143,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12799,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1611,
        "output_tokens": 13532,
        "total_tokens": 15143,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12799,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, the answer changes significantly when the circuit oscillates!\n\n## Why the Original Analysis is Invalid for Oscillation\n\nThe formula `RX ~= (1/3)(1/gmn + 1/gmp)` assumes:\n\n1. **Diode-connected operation**: Each inverter's gate and drain are effectively tied together\n2. **Small-signal analysis**: Small perturbations around a DC operating point\n3. **Simultaneous conduction**: Both NMOS and PMOS conducting in each inverter\n\n## What Actually Happens During Oscillation\n\n### 1. **No Diode Connection**\n- In the ring oscillator, each gate is driven by the *previous* stage's output\n- Gates and drains are **NOT** connected\n- This fundamentally invalidates the diode-connected assumption\n\n### 2. **Large-Signal Operation**\n- Nodes swing rail-to-rail (0 to VDD)\n- Small-signal models (using gm) don't apply\n- Transistors switch between cutoff, triode, and saturation\n\n### 3. **Alternating Conduction**\n- At any time, each inverter typically has **either** PMOS **or** NMOS strongly conducting, not both\n- Both conduct simultaneously only during brief transitions\n- The parallel resistance is dominated by whichever transistors are ON at that instant\n\n## The Correct Perspective\n\nDuring oscillation, RX becomes:\n- **Time-varying** rather than constant  \n- **Much larger on average** since only ~1 transistor per inverter conducts at any given time\n- Better characterized by **time-averaged current** over a complete cycle\n\n**Bottom line**: The simple small-signal formula is only valid for static/DC analysis and becomes meaningless once sustained oscillation begins.",
        "format": "markdown",
        "sha256": "b4a75c4aa7f08f174eea59ba340e4680d67ffa2dc8818fa7a9de9499677af6b8"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "Correctly notes that the static diode-connected small-signal model does not describe the oscillating ring, but incorrectly concludes that RX becomes much larger. The golden solution says capacitive charging sets RX, which remains on the order of the MOS on-resistance.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3410,
        "output_tokens": 2608,
        "total_tokens": 6018,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1792,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1705,
        "output_tokens": 1304,
        "total_tokens": 3009,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 896,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, the answer changes significantly when the circuit oscillates.\n\n## Why the Original Calculation Breaks Down\n\nThe calculation `RX ~= (1/3)(1/gmn + 1/gmp)` assumes:\n- Each inverter operates at a **fixed DC bias point** \n- Both NMOS and PMOS are simultaneously conducting (like diode-connected devices)\n- Small-signal linearization around this operating point is valid\n\n## What Happens During Oscillation\n\nWhen oscillating, this model fails because:\n\n### 1. **Large-Signal Operation**\n- Transistors switch between ON (saturated) and OFF states\n- The outputs swing rail-to-rail, not staying near a transition point\n- This is **large-signal** behavior, not small-signal\n\n### 2. **Time-Varying State**\nAt different times during oscillation:\n- When output is HIGH: mainly PMOS conducts, NMOS is OFF\n- When output is LOW: mainly NMOS conducts, PMOS is OFF  \n- Only briefly during transitions do both conduct simultaneously\n\n### 3. **Phase Distribution**\nWith 3 inverters oscillating:\n- Each stage is at a different phase (~120° apart)\n- At any instant, different inverters are in different states\n- The parallel combination seen from VDD is **time-varying**\n\n### 4. **Effective Resistance**\nDuring oscillation:\n- **RX becomes time-varying**, not a fixed value\n- **Average RX is typically lower** due to switching current spikes\n- The transconductances (gmn, gmp) themselves vary with the operating point\n\n## Conclusion\n\nThe diode-connected model is only valid for **small-signal analysis around a DC equilibrium**. During oscillation, you need **large-signal, time-domain analysis** to properly characterize the supply impedance.",
        "format": "markdown",
        "sha256": "ace84c9348736126a12477c59df4a0902b129ebb573d4911a4ff46ca4e75c3bb"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that oscillation invalidates the static small-signal model, but misses the dominant capacitive-charging mechanism and incorrectly claims the average resistance becomes significantly lower. The key result is that RX remains on the order of the MOS on-resistance, not much changed.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3410,
        "output_tokens": 2684,
        "total_tokens": 6094,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1826,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1705,
        "output_tokens": 1342,
        "total_tokens": 3047,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 913,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Yes, the answer changes significantly when the circuit oscillates.\n\n## Why the Original Analysis is Limited\n\nThe given formula assumes a **small-signal, DC operating point analysis** where each inverter sits in its linear region with both NMOS and PMOS partially conducting (like diode-connected devices). This is only valid for:\n- Static/equilibrium conditions\n- Very small perturbations around a DC bias point\n- Analysis during startup before oscillations build up\n\n## What Changes During Oscillation\n\n### 1. **Large-Signal Operation**\nWhen oscillating, the circuit operates in a **large-signal regime**:\n- Outputs swing rail-to-rail (full supply range)\n- Transistors fully turn ON and OFF\n- Small-signal models and linearization break down\n\n### 2. **Time-Varying Resistance**\nThe resistance RX becomes **time-dependent** RX(t) because:\n\n- **Most of the time**: Each inverter is in a rail state (output high or low)\n  - Only ONE device (PMOS or NMOS) conducts strongly\n  - NOT both devices in diode configuration\n  \n- **During transitions**: Brief shoot-through current when both devices conduct\n\n- **Phase differences**: The 3 inverters are ~120° out of phase, so they're in different states simultaneously\n\n### 3. **Effective Resistance is Higher**\nDuring steady oscillation:\n- Average current from supply is lower than predicted by the diode model\n- Most current is reactive (charging/discharging capacitors)\n- Effective average resistance is **higher** than (1/3)(1/gmn + 1/gmp)\n\n## Correct Approach for Oscillating Case\n\nUse **large-signal, time-domain analysis** or consider:\n- Time-averaged supply current\n- Dynamic/switching resistance\n- Harmonic balance methods\n\n**Bottom line**: The diode-connected model is a startup approximation. Once oscillating, you need large-signal analysis.",
        "format": "markdown",
        "sha256": "5caf56e09a2f5d26e0dbc6f210873a703d1e33ebc7764bf6146d57359954f1ed"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that oscillation requires a dynamic analysis, but incorrectly concludes the effective resistance is significantly higher because devices are off much of the time. The capacitive charging current makes RX remain on the order of the MOS on-resistance, not much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3410,
        "output_tokens": 2584,
        "total_tokens": 5994,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1678,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1705,
        "output_tokens": 1292,
        "total_tokens": 2997,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 839,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this dynamic comparator (StrongARM latch) circuit, I need to analyze how M7 affects the initial voltage gain.\n\n## Circuit Analysis\n\n**M7's Role:** M7 is the tail current source for the differential input pair (M1-M2), controlled by the clock signal CK.\n\n## Effect of Increasing W7\n\nWhen the width of M7 increases:\n\n1. **Tail current increases:** ID7 ∝ W7 (for a given VGS in saturation)\n\n2. **This affects M1-M2 operation:**\n   - Bias current through M1, M2 increases: ID1 ≈ ID2 ≈ ID7/2\n   - Transconductance increases: gm1,2 ∝ √ID ∝ √W7\n   - Output resistance decreases: ro1,2 ∝ 1/ID ∝ 1/W7\n\n3. **Initial voltage gain impact:**\n\nThe small-signal voltage gain is approximately:\n$$A_v = g_m \\times r_o$$\n\nSubstituting the dependencies:\n$$A_v \\propto \\sqrt{W_7} \\times \\frac{1}{W_7} = \\frac{1}{\\sqrt{W_7}}$$\n\n## Answer\n\n**The initial voltage gain DECREASES as W7 increases** (proportionally to 1/√W7).\n\n### Physical Interpretation:\n- While increasing W7 boosts the transconductance (speed), it more significantly reduces the output resistance of the input transistors\n- This is the classic tradeoff between gain and bandwidth in amplifier design\n- Higher bias current → faster operation but lower voltage gain\n- The intrinsic gain of transistors decreases as their bias current increases\n\nThis is why in practice, M7 is sized to balance between adequate gain for resolving small input differences and sufficient speed for the desired clock frequency.",
        "format": "markdown",
        "sha256": "9f456ce9d0c4c342fd4831793b869c93e49896ecbc0464df0b7f38d26ee69498"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that the initial gain decreases and notes that a wider M7 raises tail current. However, it explains the trend using a conventional gm·ro gain model, which is not the relevant integration-gain mechanism here; the gain falls because gm/ICM decreases.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 6935,
        "total_tokens": 8566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6483,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 6935,
        "total_tokens": 8566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6483,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of M7 Width Effect on Initial Voltage Gain\n\nLooking at this circuit, I can identify a **StrongARM latch/dynamic comparator** where:\n- M1, M2: differential input pair\n- M3, M4: cross-coupled regenerative pair\n- M5, M6: PMOS loads  \n- M7: tail current source (controlled by CK)\n\n## Effect on Initial Voltage Gain\n\nThe **initial voltage gain decreases** as M7 width increases.\n\n### Reasoning:\n\nThe small-signal voltage gain of the differential amplifier (before regeneration dominates) is:\n\n$$A_v = g_{m1} \\times R_{out}$$\n\n**When W₇ increases:**\n\n1. **Tail current increases:** \n   - $I_{tail} \\propto W_7$ (for constant $V_{GS}$)\n\n2. **Transconductance increases:**\n   - $g_{m1} = \\sqrt{2\\mu_n C_{ox}(W/L)_1 \\cdot I_{D1}}$\n   - Since $I_{D1} \\propto I_{tail}$\n   - Therefore: $g_{m1} \\propto \\sqrt{W_7}$ ✓\n\n3. **Output resistance decreases:**\n   - $r_o = \\frac{1}{\\lambda I_D}$\n   - As current through M3-M6 increases\n   - $R_{out} \\propto \\frac{1}{W_7}$ ✗\n\n4. **Net gain:**\n   $$A_v \\propto \\sqrt{W_7} \\times \\frac{1}{W_7} = \\frac{1}{\\sqrt{W_7}}$$\n\n## Conclusion\n\n**The initial voltage gain decreases** as M7 width increases because the output resistance decreases faster (linearly with current) than the transconductance increases (with square root of current).\n\n**Trade-off:** While gain decreases, speed increases with larger W₇ due to higher currents. This is a typical gain-bandwidth trade-off in comparator design.",
        "format": "markdown",
        "sha256": "80bc54859464ac99ce650737bf67be7f47690011d1ba3c75b9ed181a41615631"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The trend is correct, and the answer recognizes that a wider M7 raises tail current while input-pair gm grows only as its square root. However, it explains the initial gain using a conventional gm·Rout model and an assumed load-resistance scaling; the StrongARM’s initial gain is primarily an integration gain that falls as the increased tail current shortens the integration interval. The conclusion is right, but the mechanism is imprecise.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 5067,
        "total_tokens": 6698,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4561,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 5067,
        "total_tokens": 6698,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4561,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, I can identify it as a **StrongARM latch** or regenerative comparator with:\n- A differential input pair (M1, M2)\n- Cross-coupled NMOS pair (M3, M4) \n- Cross-coupled PMOS pair (M5, M6)\n- Tail current source M7 controlled by clock CK\n- Switching network (S1-S4) for reset/evaluation phases\n\n## Effect of Increasing M7 Width on Initial Voltage Gain\n\n**The initial voltage gain INCREASES as M7 width increases.**\n\n### Reasoning:\n\n1. **M7's Role**: M7 acts as the tail current source for the differential input pair (M1-M2) during the evaluation phase when CK is high.\n\n2. **Increased Current**: When M7 width increases (with constant VGS from clock):\n   - The tail current IT increases proportionally: $I_T \\propto \\frac{W_7}{L_7}$\n   - More current flows through M1 and M2\n\n3. **Transconductance Effect**: The transconductance of M1 and M2 depends on their bias current:\n   $$g_{m1,2} = \\sqrt{2\\mu_n C_{ox} \\left(\\frac{W}{L}\\right)_{1,2} \\cdot I_D}$$\n   - Higher tail current → higher ID for M1, M2\n   - Therefore: $g_m \\propto \\sqrt{I_D}$ increases\n\n4. **Gain Relationship**: The initial voltage gain (before regeneration dominates) is approximately:\n   $$A_v \\approx g_{m1,2} \\times Z_{load}$$\n   - Where Zload is the impedance at nodes X and Y\n   - Higher gm directly increases the gain\n\n### Summary:\nWider M7 → More tail current → Higher gm of input pair → **Higher initial voltage gain**\n\nThis also has the benefit of faster initial response, though it comes at the cost of increased power consumption and larger parasitic capacitances.",
        "format": "markdown",
        "sha256": "98975bd60ddd63021b0c3c225fc11973441c5a06c647893137afa5d5753e5eeb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M7 as the tail device and notes that widening it increases tail current and input-pair gm, but it reaches the opposite conclusion. Initial gain scales roughly with gm/ICM, so the increase in current dominates and the gain decreases.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 3868,
        "total_tokens": 5499,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3373,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 3868,
        "total_tokens": 5499,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3373,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Increasing Capacitance at Nodes P and Q\n\nLooking at this circuit, which appears to be a **clocked regenerative comparator/sense amplifier**, I can analyze the effect on initial voltage gain.\n\n## Circuit Operation\n\nThe circuit has two main phases:\n1. **Reset phase** (switches S₁-S₄ closed): Precharges nodes to VDD\n2. **Evaluation phase** (switches open, M₇ on): \n   - Differential pair M₁-M₂ converts input voltage difference to current difference\n   - Cross-coupled latches (M₃-M₄, M₅-M₆) provide regenerative amplification\n\n## Effect of Increased Capacitance\n\n**The initial voltage gain DECREASES** when capacitance at nodes P and Q increases.\n\n### Reasoning:\n\n1. **Current-to-Voltage Conversion:**\n   - The differential pair creates current difference: ΔI = g_m × ΔV_in\n   - This current charges/discharges capacitances at nodes P and Q\n   - Rate of voltage change: **dV/dt = ΔI/C**\n\n2. **With Increased Capacitance:**\n   - Larger C → slower voltage development\n   - For a given time interval, smaller initial voltage difference develops\n   - Initial voltage: ΔV(t) ∝ (g_m × ΔV_in × t) / C\n   - **Effective gain ∝ 1/C**\n\n3. **Practical Impact:**\n   - Reduced sensitivity during initial evaluation\n   - Slower response before regeneration dominates\n   - May require longer evaluation time for the latch to resolve\n\n**Answer:** Increasing capacitance at nodes P and Q **reduces the initial voltage gain** because it slows the rate at which the initial voltage difference develops during the amplification phase.",
        "format": "markdown",
        "sha256": "d5476dd73599b69925f135cae10d221ceea8ee30d402f7de3a63095143a25ea9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives the opposite of the essential result: the initial gain remains approximately unchanged. It correctly notes that increased capacitance slows the transient, but misses that the amplification phase lasts proportionally longer, canceling the capacitance dependence.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 1961,
        "total_tokens": 3592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1519,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 1961,
        "total_tokens": 3592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1519,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, which appears to be a dynamic comparator or latched amplifier (note the cross-coupled M3-M4 and the clock-controlled switches), I need to consider what \"initial voltage gain\" means in this context.\n\n## Analysis\n\n**Nodes P and Q** are the internal nodes at the drains of:\n- Node P: M1 and M3\n- Node Q: M2 and M4\n\nThese nodes have parasitic capacitance, and the question asks about adding more capacitance.\n\n## Effect on Initial Voltage Gain\n\n**The initial voltage gain decreases** (is reduced) when capacitance at nodes P and Q increases.\n\n### Reasoning:\n\n1. **Dynamic Response**: In this switched/clocked circuit, during the evaluation phase, the current from the differential pair (M1, M2) must charge/discharge the capacitance at nodes P and Q.\n\n2. **Voltage Rate of Change**: The relationship is:\n   $$\\frac{dV}{dt} = \\frac{I}{C}$$\n   \n   With larger C, the voltage changes more slowly for the same current.\n\n3. **Initial Gain Definition**: In dynamic circuits, \"initial gain\" typically refers to the voltage amplification achieved during the early part of the evaluation phase. With increased capacitance:\n   - Voltage builds up more slowly\n   - Less voltage change occurs in a given time\n   - The effective initial gain is reduced\n\n4. **Bandwidth Effect**: The pole frequency ω = 1/(R·C) decreases, reducing bandwidth and slowing the transient response.\n\n### Summary:\n- **DC gain** (gₘ × Rₒᵤₜ): unchanged\n- **Initial/dynamic gain**: **decreases**  \n- **Bandwidth**: decreases\n- **Settling time**: increases",
        "format": "markdown",
        "sha256": "90e9b38b990f62c8e7aef0cafbedef4f19689b2dca508367130cf8fe0e4be53c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that larger capacitance slows the transient, but incorrectly concludes that the initial gain decreases. The longer amplification interval compensates for the slower voltage slew, leaving the initial gain approximately unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 2573,
        "total_tokens": 4204,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2151,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 2573,
        "total_tokens": 4204,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2151,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, which appears to be a **StrongARM latch** or clocked comparator, I need to analyze what happens during the initial amplification phase when the clock (CK) goes high.\n\n## Circuit Operation\n\nDuring evaluation (CK high):\n1. M7 turns on, providing tail current\n2. Input differential pair M1-M2 converts input voltage difference to current difference: ΔI ≈ g_m × ΔV_in\n3. This current charges/discharges nodes P and Q\n4. Voltage changes at P and Q modulate M3 and M4\n5. Cross-coupled latches eventually cause regenerative amplification\n\n## Effect of Increasing Capacitance at P and Q\n\nThe **initial voltage gain decreases** when capacitance at nodes P and Q increases.\n\n### Reasoning:\n\n**Time-domain perspective:**\n- The voltage change rate at nodes P and Q is given by: **dV/dt = I/C**\n- Larger capacitance → slower voltage change\n- For the same time interval, ΔV = (I/C)·Δt is smaller with larger C\n- This produces a weaker signal to drive the gates of M3/M4\n- Result: **Lower initial gain**\n\n**Frequency-domain perspective:**\n- Added capacitance creates poles in the transfer function\n- The impedance at P and Q becomes Z ≈ 1/(jωC)\n- Larger C → lower pole frequency → reduced bandwidth\n- This reduces the high-frequency/transient gain\n- Result: **Lower initial gain**\n\n## Summary\n\nIncreasing capacitance at nodes P and Q **DECREASES** the initial voltage gain because it slows down the voltage development at these critical nodes during the early amplification phase, reducing the signal available to drive the regenerative latch.",
        "format": "markdown",
        "sha256": "b979dc7f531d55c034c2a666d9a28064078dfffb969cdcbcfe22a062b747b85c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer correctly notes that larger capacitance slows the node-voltage transient, but mistakes the smaller change over a fixed time for lower initial gain. The longer amplification interval offsets the slower slope, so the initial gain remains approximately unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 3662,
        "total_tokens": 5293,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3238,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1631,
        "output_tokens": 3662,
        "total_tokens": 5293,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3238,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, this is a **StrongARM latch** (clocked regenerative comparator). Let me analyze what happens when we increase the widths of M5 and M6.\n\n## Circuit Operation Context\n\n- **M5 and M6** are the cross-coupled PMOS pair providing positive feedback during regeneration\n- During evaluation (CK high), the cross-coupled pairs (M3-M4 and M5-M6) regeneratively amplify the small voltage difference between nodes X and Y\n\n## Effect of Increasing M5 and M6 Width\n\n**The speed IMPROVES**. Here's why:\n\n### 1. **Regeneration Time Constant**\nThe regeneration speed is governed by:\n$$\\tau_{regen} = \\frac{C_{load}}{g_{m,n} + g_{m,p}}$$\n\nWhere:\n- $g_{m,n}$ = transconductance of NMOS pair (M3, M4)\n- $g_{m,p}$ = transconductance of PMOS pair (M5, M6)\n\n### 2. **Competing Effects**\nWhen increasing W of M5/M6:\n\n✅ **Positive effect (dominant):**\n- $g_m \\propto W$ increases linearly\n- Stronger positive feedback and faster regeneration\n\n⚠️ **Negative effect:**\n- Parasitic capacitance increases (drain/source junctions, gate capacitance)\n- Slightly slower charging/discharging\n\n### 3. **Net Result**\nThe **gm increase dominates** because:\n- gm scales linearly with W\n- Only *some* capacitance components increase (M5/M6 parasitics)\n- Other capacitances (from M3, M4, M1, M2, routing) remain constant\n- The ratio $(g_{m,n} + g_{m,p})/C$ increases\n\n## Conclusion\n**Speed improves** - the regeneration becomes faster due to stronger positive feedback, which is particularly important since PMOS devices typically have lower transconductance than NMOS (lower mobility), so increasing M5/M6 helps balance the regeneration strength.",
        "format": "markdown",
        "sha256": "7fa5ed352616a27d5363e41ce4b1e664e057b73b3541f5f80da8b48d7514b967"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies M5/M6 as regenerative PMOS devices and explains that their stronger transconductance initially improves speed despite added parasitics. However, it omits the eventual capacitance limit and optimum-width caveat, and implies the improvement continues.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 2543,
        "total_tokens": 4176,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2031,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 2543,
        "total_tokens": 4176,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2031,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **dynamic latched comparator** circuit, if we increase the widths of M5 and M6, the **speed will DEGRADE** (become slower).\n\nHere's why:\n\n## Key Effects of Increasing M5 and M6 Width:\n\n### 1. **Increased Capacitive Loading** ❌\n- Larger transistors have greater parasitic capacitances (gate, drain, junction capacitances)\n- This increases the total capacitance at nodes X and Y\n- During the comparison phase, the differential pair (M1-M2) must build up a voltage difference across these nodes\n- More capacitance = slower initial voltage development\n\n### 2. **Regeneration Phase Trade-off**\nWhile larger M5 and M6 provide:\n- ✅ Higher transconductance (gm) → stronger pull-up current\n- ❌ Higher capacitance at the latch nodes\n\nThe regeneration time constant is approximately:\n$$\\tau_{regen} \\propto \\frac{C_{total}}{g_m}$$\n\nSince both C and gm increase roughly proportionally with width, but:\n- Total capacitance includes parasitics that don't contribute to gm improvement\n- The capacitance penalty typically dominates\n\n### 3. **Initial Comparison Slows Down** ❌\n- Before regeneration kicks in effectively, a sufficient voltage difference must develop\n- Larger capacitance at X and Y means the limited current from the input differential pair takes longer to create this initial imbalance\n\n## Conclusion:\n**Speed degrades** - the increased capacitive loading slows both the initial comparison phase and overall latching operation. This is why in comparator design, you balance the latch transistor sizes carefully, avoiding excessive sizing of M5 and M6.",
        "format": "markdown",
        "sha256": "36b48eca1c404df340a468a4c76e9a081333a40eedd73a346ac4abc5e1c65b13"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes both the added node capacitance and increased gm, but incorrectly says capacitance dominates initially and concludes speed degrades. The stronger regeneration improves speed over the initial sizing range; capacitance limits the benefit only at larger widths.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 2141,
        "total_tokens": 3774,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 2141,
        "total_tokens": 3774,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of M5 and M6 Width Impact on Speed\n\nThis is a **clocked comparator/sense amplifier** with a cross-coupled regenerative latch. Let me analyze how increasing M5 and M6 widths affects speed.\n\n## Circuit Components:\n- M1, M2: Input differential pair\n- M3, M4: NMOS cross-coupled latch\n- M5, M6: PMOS cross-coupled latch\n- M7: Tail current source\n- S1-S4: Reset switches\n\n## Effect of Increasing M5/M6 Width:\n\n### ✅ **Positive Effects (Speed Improvement):**\n1. **Increased transconductance (gm)**: gm ∝ W\n2. **Stronger positive feedback** during regeneration\n3. **Faster pull-up capability** at nodes X and Y\n4. **Improved regeneration time constant**: τ = C/(gm,n + gm,p)\n\n### ⚠️ **Negative Effects (Speed Degradation):**\n1. **Increased parasitic capacitance** at nodes X and Y (Cgs, Cgd, Cdb ∝ W)\n2. **More capacitive loading** for the input differential pair\n3. **Slower initial charging** before regeneration kicks in\n\n## **Answer: Speed IMPROVES** (within reasonable limits)\n\nThe regeneration time constant τ = C/(gm,n + gm,p) shows that while both capacitance and gm increase with width, the **gm term in the denominator dominates**, leading to faster regeneration. The positive feedback strength improvement outweighs the capacitive loading effect.\n\n**However**, there's an optimal point - excessive width eventually degrades speed due to dominant capacitive loading and diminishing gm returns.",
        "format": "markdown",
        "sha256": "0a89b438d247cbb06063a6fe5bae0888b428717ef356a055177f8a21ffb63547"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that widening M5/M6 initially improves regeneration speed and that added parasitic capacitance eventually limits the benefit, giving an optimum width.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 1233,
        "total_tokens": 2866,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 806,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1633,
        "output_tokens": 1233,
        "total_tokens": 2866,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 806,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this dynamic logic circuit, increasing the width of the clocked transistors (those controlled by CK and CK̄) will generally **DEGRADE** the speed.\n\n## Here's why:\n\n### Trade-offs when increasing clocked transistor widths:\n\n**Benefits (+):**\n- Lower on-resistance → faster precharge (PMOS) and evaluation (NMOS)\n- Better current drive capability\n\n**Penalties (-):**\n1. **Increased clock loading**: Wider transistors have larger gate capacitances, significantly increasing the load on the clock network. The clock edges will be slower to arrive at all clocked transistors.\n\n2. **Increased node capacitance**: The drain capacitances of these wider transistors add to the capacitance at nodes X and Y, making them slower to charge and discharge.\n\n3. **Diminishing returns**: In a well-designed circuit, the clocked transistors are typically already sized adequately. Further widening provides marginal resistance reduction while adding substantial capacitance.\n\n### The limiting factor:\n\nThe circuit's speed is determined by:\n```\nt_total = t_clock_skew + t_precharge/evaluation + t_output\n```\n\nWhen clocked transistors are widened:\n- The **clock distribution delay increases** (more capacitive load on CK)\n- The charge/discharge time of internal nodes **may not improve** much since τ = RC, and both R and C scale with width\n- The **system-level clock penalty dominates**\n\n### Conclusion:\nSpeed **DEGRADES** because the increased capacitive loading on the clock network and internal nodes outweighs the benefit of reduced on-resistance, especially if the transistors are already reasonably sized.",
        "format": "markdown",
        "sha256": "3e3c0944a49e51937876786ecae496d3519b9dafa8e3d40dbe81cdf115458740"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes the resistance–capacitance tradeoff, but concludes that widening generally degrades speed and misses the key result that speed improves initially before added capacitance may limit or reverse the benefit.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 4799,
        "total_tokens": 6406,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4407,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 4799,
        "total_tokens": 6406,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4407,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Clocked Transistor Width Impact\n\nLooking at this circuit, I can identify it as **dynamic/domino logic** with two pipeline stages. The \"clocked transistors\" are those controlled by CK and CK̄ signals.\n\n## Effect of Increasing Clocked Transistor Widths: **Speed DEGRADES**\n\n### Trade-offs:\n\n**Potential Benefits:**\n- ✓ Lower R_on → faster precharge/evaluation of nodes X and Y\n- ✓ Stronger drive capability\n\n**Dominant Drawbacks:**\n- ✗ **Increased clock network loading** (larger gate capacitances)\n- ✗ Increased parasitic capacitances at nodes X and Y (drain/source caps)\n- ✗ Slower clock rise/fall times across the entire circuit\n\n### Why Speed Degrades:\n\n1. **Clock Loading is Critical**: The clock signal must drive ALL clocked transistors across the chip. Wider transistors mean much larger capacitive load on the clock distribution network.\n\n2. **Slower Clock Transitions**: The clock driver must charge/discharge more gate capacitance, resulting in slower clock edges. This directly impacts the maximum operating frequency.\n\n3. **Increased Parasitic Capacitance**: While R_on decreases with width W, the parasitic capacitances (C_gate, C_diffusion) increase with W. The benefit from lower resistance is offset by higher capacitance.\n\n4. **Net Delay Effect**: The RC time constant (τ = RC) doesn't improve proportionally because:\n   - R ∝ 1/W  \n   - C ∝ W\n   - Net effect is minimal improvement or degradation\n\n### Conclusion:\n**Speed degrades** because the clock network loading becomes a bottleneck that outweighs any benefits from faster local switching. Optimal performance requires carefully sized clocked transistors that balance drive strength against capacitive loading.",
        "format": "markdown",
        "sha256": "abbf01c8d39063614a9077a4ade9afc94b94673ac684b393855d22239817881f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that wider devices reduce on-resistance and add capacitance, but misidentifies the C2MOS divider as domino logic with pipeline stages and gives the opposite speed trend. The topology misread triggers the golden solution’s cap of 1.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 2452,
        "total_tokens": 4059,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 2452,
        "total_tokens": 4059,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Speed Impact\n\nLooking at this dynamic/domino logic circuit, the \"clocked transistors\" are those controlled by CK and CK̄ signals. Let me analyze what happens when we increase their widths.\n\n## Effects of Increasing Clocked Transistor Width\n\n### Positive Effect\n- **Reduced ON-resistance**: Larger transistors → lower resistance → potentially faster charging (precharge phase) and discharging (evaluation phase)\n\n### Negative Effects\n\n1. **Increased Gate Capacitance**:\n   - More load on the clock network (CK and CK̄)\n   - Slower clock edges → increased clock skew\n   - This affects the entire timing of the circuit\n\n2. **Increased Parasitic Capacitance at Nodes X and Y**:\n   - Larger drain/source capacitances\n   - More total capacitance that must be charged during precharge\n   - More total capacitance that must be discharged during evaluation\n\n## Net Result: **Speed DEGRADES**\n\n### Why?\n\nIn a reasonably designed dynamic logic circuit:\n\n1. **Clock loading becomes critical**: The gate capacitance increase directly loads the clock distribution network, slowing down clock transitions system-wide\n\n2. **Diminishing returns on resistance**: The clocked transistors in a well-designed circuit are typically already sized so they're not the bottleneck. Further reducing their resistance provides minimal benefit\n\n3. **Unfavorable RC tradeoff**: The increased parasitic capacitance (∝ W) negates the benefit of reduced resistance (∝ 1/W), especially when other capacitances at nodes X and Y are considered\n\n4. **Series path consideration**: For evaluation, the discharge path goes through clocked NMOS → M1 → ground. If M1 is the limiting resistor, reducing the clocked transistor resistance further doesn't help much\n\n**Conclusion**: Increasing the widths of clocked transistors beyond their optimal sizing degrades speed due to excessive clock loading and increased node capacitances.",
        "format": "markdown",
        "sha256": "25495c4c2e92cbcfbafd92f624f9921165d1f9fab3b70799051af9ea8aeb4cb9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that wider clocked devices lower resistance but add capacitance, yet concludes that widening degrades speed rather than improving it initially before capacitance limits the benefit. The golden solution assigns 2 to answers with this degradation conclusion.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 3709,
        "total_tokens": 5316,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3246,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 3709,
        "total_tokens": 5316,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3246,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Quadrature Output Capability\n\n**No, this structure does NOT provide quadrature outputs.**\n\n## Reasons:\n\n1. **Single Output**: The circuit shows only **one output (Z)**, which is taken from node Y through inverter Inv3. Quadrature outputs require two outputs that are 90° out of phase.\n\n2. **Two-Stage Topology**: This appears to be a two-stage cross-coupled structure. Such configurations typically produce:\n   - **Differential outputs** (180° phase difference), NOT\n   - **Quadrature outputs** (90° phase difference)\n\n3. **What Would Be Needed for Quadrature**:\n   - **Four-stage ring oscillator**: Each stage provides ~90° phase shift\n   - **Special coupling networks**: To create 90° phase relationships between stages\n   - **Two explicit outputs**: Labeled as I (in-phase) and Q (quadrature), taken from nodes X and Y\n\n## What This Circuit Likely Is:\n\nThis appears to be a **clocked differential latch** or a **two-stage switched circuit** with:\n- Cross-coupled stages for regenerative feedback\n- Clock-controlled switching (CK and CK̄)\n- Single-ended output after inversion\n\nFor true quadrature generation, you would need either a 4-stage architecture or additional coupling circuitry to establish the 90° phase relationship between outputs.",
        "format": "markdown",
        "sha256": "2afd4a2ffb67ecd7adbb6aa88d7bf10203bfce5abef1eb90e1d3ae0cc30bced0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misses the C2MOS divide-by-two topology and incorrectly claims there is only one output and that quadrature requires a four-stage oscillator. The latches switch half an input period apart, giving nominal quadrature.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 1407,
        "total_tokens": 2998,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1081,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 1407,
        "total_tokens": 2998,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1081,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis\n\nNo, this structure **does not provide quadrature outputs**.\n\n## Reasoning:\n\n**What we see:**\n- A **2-stage differential oscillator** circuit\n- Clock-switched differential pairs (CK and CK̄)\n- Only **one output (Z)** is shown from the inverter\n- Nodes X and Y are internal differential nodes\n\n**Why not quadrature:**\n\n1. **Stage count**: Quadrature outputs require 90° phase separation. In a ring oscillator, you need **4 stages** to generate quadrature signals (360°/4 = 90° per stage)\n\n2. **This 2-stage configuration** produces signals that are approximately **180° apart** (differential/complementary), not 90°\n\n3. **Single output**: Only one output (Z) is explicitly shown, not the two independent signals (I and Q) needed for quadrature\n\n**What would be needed for quadrature:**\n- Either a **4-stage ring oscillator** \n- Or **additional divide-by-2 circuitry** with proper phase extraction\n- Or a **polyphase filter** to generate quadrature from a single-phase signal\n- Two distinct outputs labeled as I and Q (or 0° and 90°)\n\nThis appears to be a standard differential VCO that produces a single oscillating output, not a quadrature oscillator.",
        "format": "markdown",
        "sha256": "2dc2ca28533c8fa22f958386b7a7dbc158cc29c18d5389c30ae195a64e5789e4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the C2MOS divide-by-two as a differential ring oscillator and misses that its opposite-edge latch transitions provide nominal quadrature. Its conclusions about 180° phase and needing a four-stage ring do not apply.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 964,
        "total_tokens": 2555,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 644,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 964,
        "total_tokens": 2555,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 644,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Quadrature Output Capability\n\n**No, this structure does NOT provide quadrature outputs.**\n\nHere's why:\n\n## Key Observations:\n\n1. **Single Output**: The circuit shows only **one output (Z)** through inverter Inv₃, not the two or four outputs typically required for quadrature signals.\n\n2. **Circuit Type**: This appears to be a **CML (Current Mode Logic) frequency divider** or **master-slave latch configuration**, likely functioning as a divide-by-2 circuit.\n\n3. **Quadrature Requirements**: True quadrature outputs require:\n   - At least **two signals** (I and Q)\n   - **90° phase separation** between them\n   - Both signals explicitly available as outputs\n\n## What Would Be Needed for Quadrature:\n\nFor quadrature generation, you would typically need:\n- **Four-stage ring oscillator** (for QVCO)\n- **Two separate output paths** for I and Q channels\n- Outputs taken from nodes 90° apart in the oscillation cycle\n\n## What This Circuit Likely Does:\n\n- **Frequency division** (divide-by-2 of the input clock CK)\n- Single-ended output at node Z\n- While internal nodes X and Y exist, they're not brought out as quadrature outputs\n\n**Conclusion**: This is a single-output frequency divider, not a quadrature generator.",
        "format": "markdown",
        "sha256": "b3d81a5ae5b0bccc40185f5261e4182f116a9fcef6318e43c45cc5aed69b896b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes a divide-by-two function, but incorrectly concludes there is no quadrature because only one output is shown. The latch nodes X and Y are nominally 90° apart; the answer misses this central result and misidentifies the circuit as possibly CML.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 1059,
        "total_tokens": 2650,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 730,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1591,
        "output_tokens": 1059,
        "total_tokens": 2650,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 730,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Clocked Transistor Width in Dynamic Logic\n\nThis circuit is a **dynamic/domino logic gate** with clocked precharge (PMOS) and evaluation (NMOS) transistors.\n\n## Trade-offs when increasing clocked transistor widths:\n\n### ✅ **Improves Speed (Local Effects):**\n- **Lower on-resistance**: R_on ∝ 1/W → faster precharge and evaluation\n- **Stronger drive**: Precharge PMOS charge internal nodes faster\n- **Reduced series resistance**: Footer NMOS provide less resistance during evaluation\n\n### ❌ **Degrades Speed (Global Effects):**\n- **Increased clock load**: C_gate ∝ W × L\n- **Slower clock edges**: More capacitance on CK signal\n- **Clock distribution delay**: All clocked transistors (across all stages) load the clock network\n\n## Answer:\n\n**There is an OPTIMAL width** - beyond this point, **speed DEGRADES**.\n\nIn dynamic logic design, the clock loading effect is particularly critical because:\n\n1. Clock drives many transistors (all precharge/footer devices across multiple stages)\n2. Total clock load grows as: N_stages × (W_pmos + W_footer)  \n3. Slow clock transitions cause:\n   - Increased switching time\n   - Charge sharing issues\n   - Potential race conditions\n\n**Conclusion**: While moderate sizing improves speed, **excessive widening of clocked transistors degrades speed** due to the clock network becoming the bottleneck. The clock load penalty typically outweighs the local gate speedup in practical designs.",
        "format": "markdown",
        "sha256": "220b68b569b9c5f5d0d7a93aae99c61f2469f53aa29bda88c092220d5f904b1b"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It describes an initial speed improvement from reduced on-resistance followed by a limit from increased clock loading, and flags charge sharing as a downside—an improvement-then-degradation trend allowed by the golden solution.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3230,
        "output_tokens": 6374,
        "total_tokens": 9604,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5620,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1615,
        "output_tokens": 3187,
        "total_tokens": 4802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2810,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Clocked Transistor Width Effects\n\nThis circuit appears to be a **dynamic logic circuit** (likely C²MOS or a clocked latch) where the CK-controlled transistors act as switches for precharge/evaluate operations.\n\n## Effect of Increasing Clocked Transistor Width\n\n**The speed will generally IMPROVE**, but with trade-offs:\n\n### Benefits (Speed Improvement) ✓\n\n1. **Reduced ON-resistance (Ron)**\n   - Ron ∝ 1/W\n   - Lower resistance allows faster charging/discharging of internal nodes\n   - Critical precharge and evaluate phases complete faster\n\n2. **Higher drive current**\n   - Id ∝ W\n   - Can more quickly charge/discharge node capacitances\n\n### Drawbacks (Speed Degradation)\n\n1. **Increased parasitic capacitance**\n   - Gate capacitance (Cg ∝ W): loads the clock network\n   - Drain/source capacitance (Cd, Cs ∝ W): loads internal nodes\n\n2. **Clock loading**\n   - Larger gates require more charge from clock driver\n   - Could slow clock edges if driver is weak\n\n## Net Effect\n\nFor moderately-sized increases: **IMPROVE** ✓\n\nThe RC delay through the clocked transistor (Ron × Cload) typically **decreases** because:\n- Ron decreases by factor α\n- Cload increases by less than α (since it includes other contributions)\n\n## Optimal Sizing\n\nThere's an optimal width where benefits and drawbacks balance. Beyond this point, excessive width causes diminishing returns or degradation due to capacitive loading dominance.\n\n**Answer: Speed typically IMPROVES with increased clocked transistor width** (assuming reasonable sizing and adequate clock buffering).",
        "format": "markdown",
        "sha256": "48976a92df876fc17552dccfa4e83e181766b2602e2f372df5338ec18d888f4f"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that increasing clocked-transistor width improves speed and identifies lower on-resistance as the reason. It omits the topology-specific charge-sharing effect that degrades swing and limits the improvement.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3230,
        "output_tokens": 5268,
        "total_tokens": 8498,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4442,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1615,
        "output_tokens": 2634,
        "total_tokens": 4249,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2221,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of Clocked Transistor Width Impact\n\nLooking at this circuit, which appears to be a **dynamic CMOS logic** or **clocked latch** structure, the \"clocked transistors\" are the four transistors with CK at their gates:\n- Two PMOS transistors at the top (connected to VDD)\n- Two NMOS transistors at the bottom (connected to ground)\n\n## Effect of Increasing Clocked Transistor Width\n\n**Speed generally IMPROVES**, but with trade-offs.\n\n### Why Speed Improves:\n\n1. **Faster Precharge (CK = 0)**\n   - PMOS clocked transistors turn ON\n   - Wider transistors have lower on-resistance (Ron)\n   - Internal nodes charge to VDD more quickly\n\n2. **Faster Evaluation (CK = 1)**\n   - NMOS clocked transistors turn ON\n   - Lower resistance in the evaluation path to ground\n   - Conditional discharge happens faster\n\n3. **Critical Path Impact**\n   - These clocked transistors are directly in the timing-critical paths\n   - Reducing their resistance directly improves clock-to-output delay\n\n### Trade-offs:\n\n1. **Increased Clock Load**\n   - Wider transistors have higher gate capacitance\n   - Adds burden to the clock driver\n   - Can cause clock distribution delays\n\n2. **Increased Node Capacitance**\n   - Higher drain/source capacitances at internal nodes\n\n## Conclusion\n\n**Speed IMPROVES** initially because the reduction in on-resistance is more beneficial than the increased capacitive loading. However, there's an optimal width beyond which diminishing returns occur or clock loading becomes dominant.\n\nFor typical designs, making clocked transistors wider (within reason) improves performance.",
        "format": "markdown",
        "sha256": "ecce93e5419bccc8e0675497b1aec1ceea1cfd9b2bb70c4d206219d41af34420"
      },
      "model_call_count": 2,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly concludes that widening the clocked transistors initially improves speed because their lower on-resistance helps. However, it misses the key charge-sharing effect and incorrectly suggests the devices directly load the critical path; the golden solution assigns 3 when the speed conclusion is right but charge sharing is omitted.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 3230,
        "output_tokens": 4436,
        "total_tokens": 7666,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3618,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1615,
        "output_tokens": 2218,
        "total_tokens": 3833,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1809,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 2,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\nThis circuit shows a **3-stage ring oscillator with clock-controlled transmission gates** and feedback configuration.\n\n## Key Components:\n\n1. **Three Inverter Stages**: Triangular symbols with output inversion (circles at outputs)\n\n2. **Control Signals**:\n   - **CK**: Clock signal\n   - **C̄K**: Inverted clock (complementary)\n   - **Inv₁**: Input/control signal\n\n3. **Transmission Gates**: The small circles along the signal path indicate transmission gates or switches controlled by the clock signals\n\n4. **Feedback Loop**: Output of the final stage feeds back to the input\n\n## Functionality:\n\nThis is likely a **controllable ring oscillator** or **circular delay chain** where:\n\n- The complementary clocks (CK and C̄K) control when signals propagate through each stage\n- Creates a **master-slave** or **level-sensitive** latch configuration\n- Prevents race conditions by alternating which stages are active\n- The odd number of inversions (3) causes oscillation when enabled\n\n## Typical Applications:\n\n- **Clock generation circuits**\n- **Frequency dividers** \n- **Delay measurement** (ring oscillator test structures)\n- **Phase-locked loops (PLLs)**\n- **On-chip oscillators**\n\nThe Inv₁ signal likely serves to initialize, enable/disable, or inject a specific state into the oscillator.",
        "format": "markdown",
        "sha256": "d1b074e2293a90440cf55b1efcb975e0b7c194d2a0de8e6cd25c5ed74a41ed92"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes clock-controlled switches and mentions a latch configuration, but misidentifies the circuit as a ring oscillator rather than a dynamic-latch divide-by-two and does not explain the half-frequency output.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1149,
        "total_tokens": 2604,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 818,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1149,
        "total_tokens": 2604,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 818,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis: Dynamic Latch/Register\n\n## Circuit Components\n\nThis circuit shows a **three-stage inverter-based dynamic latch** with the following elements:\n\n1. **Three Inverters**: Indicated by triangular symbols with output bubbles (circles)\n2. **Transmission Gates**: Two pass gates controlled by complementary clock signals\n3. **Clock Signals**: \n   - CK (clock)\n   - CK̄ (inverted clock)\n4. **Feedback Loop**: Output returns to input\n\n## Circuit Operation\n\n### Signal Flow:\n```\nInput → [TG: CK] → Inv₁ → [TG: CK̄] → Inv₂ → Inv₃ → Output → Feedback\n```\n\n### Two Operating Phases:\n\n**1. When CK = HIGH (CK̄ = LOW):**\n- First transmission gate: CLOSED (conducting)\n- Second transmission gate: OPEN (non-conducting)\n- Input data enters and is captured by Inv₁\n\n**2. When CK = LOW (CK̄ = HIGH):**\n- First transmission gate: OPEN (isolates input)\n- Second transmission gate: CLOSED (conducting)\n- Data propagates through Inv₂ and Inv₃, stored in the loop\n\n## Function\n\nThis is a **Master-Slave Dynamic Latch** or **C²MOS Latch** commonly used for:\n- Edge-triggered data storage\n- Pipeline registers\n- Shift register stages\n- Sequential logic circuits\n\n## Key Characteristics:\n- ✓ Level-sensitive (latch behavior)\n- ✓ Low power (dynamic storage)\n- ✓ Compact design (3 inverters + 2 transmission gates)\n- ⚠ Requires continuous clocking to maintain state",
        "format": "markdown",
        "sha256": "3deca52e04a4eeaccac4a95b82358ab056274d36c70c022d549a3a9ecf2bda07"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes dynamic, master-slave latch circuitry, but misses the essential function: the arrangement divides the clock frequency by two. It instead describes a generic data latch/register and its operation.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1178,
        "total_tokens": 2633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 751,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1178,
        "total_tokens": 2633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 751,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Circuit Analysis\n\nThis is a **ring oscillator with clock-controlled transmission gates** (or alternatively, a **dynamic latch** structure depending on the connection details).\n\n## Key Components:\n\n1. **Three Inverters** - shown as triangles with output bubbles (circles indicating inversion)\n2. **Two Transmission Gates** - controlled by complementary clock signals (CK and CK̄)\n3. **Feedback Loop** - output connects back to input via the bottom path\n\n## Structure:\n- **First stage**: Transmission gate (CK controlled) → Inverter (Inv₁)\n- **Second stage**: Transmission gate (CK̄ controlled) → Inverter  \n- **Third stage**: Inverter → feedback to input\n\n## Operation:\n\n### When CK = HIGH (CK̄ = LOW):\n- First transmission gate is ON (conducting)\n- Second transmission gate is OFF (blocking)\n- Signal can enter the first inverter stage\n\n### When CK = LOW (CK̄ = HIGH):\n- First transmission gate is OFF\n- Second transmission gate is ON\n- Signal propagates through remaining stages\n\n## Likely Function:\n\nThis configuration most resembles a **dynamic latch** or **level-sensitive storage element** where:\n- The complementary transmission gates control signal flow\n- The odd number of inverters (3) provides inversion and signal restoration\n- The feedback creates memory capability\n\nAlternatively, if both transmission gates are simultaneously open, the **odd number of inverters in the feedback loop** would create oscillation (ring oscillator behavior).",
        "format": "markdown",
        "sha256": "de2ba2df4b3f873fb14df7c6d998a0b388a39c739368a6f8b531b1ed8c488c02"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes clocked transmission gates, feedback, and a possible dynamic-latch structure, but does not identify the essential divide-by-two function. Its ring-oscillator interpretation is incorrect.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1360,
        "total_tokens": 2815,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1000,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1455,
        "output_tokens": 1360,
        "total_tokens": 2815,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1000,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of the Red Inverter on Performance\n\nThis appears to be a **ring oscillator** circuit with clock-gating capability. The red inverter (Inv₁) affects performance in several key ways:\n\n## 1. **Oscillation Frequency**\n- The red inverter contributes propagation delay to the overall ring\n- The oscillation frequency is determined by: **f = 1/(2·N·τ)** where N is the number of inverting stages and τ is average delay per stage\n- Increasing the red inverter's size reduces its delay but increases loading on previous stage\n- Decreasing its size increases delay but reduces power consumption\n\n## 2. **Power Consumption**\n- Adds both **dynamic power** (switching) and **static power** (leakage)\n- Dynamic power: P ∝ C·V²·f where C includes the inverter's output capacitance\n- Larger inverter = more power consumption\n\n## 3. **Phase Noise and Jitter**\n- Contributes to timing uncertainty in the oscillator\n- Device noise and supply variations in this inverter add to overall jitter\n- Poor matching or weak drive strength increases jitter\n\n## 4. **Signal Integrity**\n- Provides signal restoration and gain in the feedback loop\n- Ensures sharp transitions needed for proper oscillation\n- Helps overcome losses from transmission gates\n\n## 5. **Critical for Oscillation**\n- Part of the **odd-number inversion** requirement for ring oscillators\n- Without proper inversion count, the circuit won't oscillate\n\nThe red inverter must be carefully sized to balance speed, power, and noise performance.",
        "format": "markdown",
        "sha256": "8bb33b9fa907d61dfc016c0a10fe93015e0b9af2f349c385b09cd1d11bfc0453"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the circuit as a ring oscillator and treats the red inverter as a normal delay stage. It misses the key feedforward bypass that improves divider speed and the unclocked branch’s low-frequency drawback, so its analysis is based on the wrong topology.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 933,
        "total_tokens": 2189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 933,
        "total_tokens": 2189,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Impact of the Red Inverter on Performance\n\nThis circuit appears to be a **clock-gated ring oscillator**. The red inverter (Inv₁) has several critical effects on performance:\n\n## 1. **Oscillation Frequency**\n- The red inverter adds **propagation delay** to the feedback loop\n- The oscillation frequency is inversely proportional to the total loop delay\n- Formula: f_osc ≈ 1/(2 × n × t_pd), where n is the number of inverters and t_pd is the propagation delay\n- **Larger/slower red inverter → lower oscillation frequency**\n\n## 2. **Required Odd Inversions**\n- Ring oscillators require an **odd number** of inversions to oscillate\n- Red inverter (1) + two black inverters (2) = **3 inversions total** ✓\n- Without the red inverter, you'd have only 2 inversions (even number), and the circuit would **latch rather than oscillate**\n\n## 3. **Drive Strength and Loading**\n- The red inverter must drive the load of the subsequent stage\n- If undersized: slower transitions, lower frequency, potential failure to oscillate\n- If oversized: higher power consumption, larger area\n\n## 4. **Power Consumption**\n- Contributes to dynamic power: P = α × C_L × V_DD² × f\n- Sizing affects both switching activity and capacitive load\n\n## 5. **Jitter and Noise Performance**\n- The inverter's delay variation contributes to **timing jitter**\n- Its noise margin affects robustness to supply/substrate noise\n\n**In summary**: The red inverter is essential for functionality (providing necessary inversion) and directly impacts frequency, power, and timing characteristics of the oscillator.",
        "format": "markdown",
        "sha256": "ad46548aa754f761f32fb5679715554bdab415802ff49db5dcedbd5955c4b639"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer mistakes the divider for a ring oscillator and misses the red inverter’s feedforward speed benefit and its key low-frequency drawback. It has only limited relevant insight in noting that the branch can form a three-inversion loop.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 996,
        "total_tokens": 2252,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 578,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 996,
        "total_tokens": 2252,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 578,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Impact of the Red Inverter (Inv₁)\n\nThe red inverter in the feedback path affects the circuit performance in several key ways:\n\n## 1. **Oscillation Frequency**\n- **Decreases frequency**: The inverter adds propagation delay to the feedback loop. Since oscillation period T = 2 × (sum of all delays), adding Inv₁ increases the total delay and thus **lowers the oscillation frequency**.\n- Formula: f_osc = 1/(2N × t_pd), where N is the number of inverters and t_pd is delay per stage\n\n## 2. **Phase/Inversion Count**\n- **Maintains odd inversion**: Ring oscillators require an odd number of inversions to oscillate. The red inverter contributes to achieving this requirement.\n- Without it, the circuit might not oscillate properly or would need redesign\n\n## 3. **Signal Integrity**\n- **Signal restoration**: Provides signal buffering and level restoration in the feedback path\n- **Stronger drive**: Ensures adequate drive strength for the input stage\n\n## 4. **Power Consumption**\n- **Increases power**: Additional inverter consumes dynamic switching power and leakage power\n- Power ∝ number of switching gates\n\n## 5. **Design Flexibility**\n- **Tuning parameter**: Sizing Inv₁ differently from other inverters allows fine-tuning of the oscillation frequency\n- Can be used to balance delays in the loop\n\n**Summary**: The red inverter primarily trades off lower oscillation frequency and higher power for correct circuit operation and better signal integrity.",
        "format": "markdown",
        "sha256": "4f1dbf7a137ffbb7f12c349f5fc075f836d15bc794ab72d2b30858dd7fd46502"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer mistakes the red inverter for a ring-oscillator stage. It misses the feedforward path that bypasses part of the first latch, its high-speed benefit, and the unclocked branch's low-frequency drawback, instead claiming the inverter enables oscillation.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 828,
        "total_tokens": 2084,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 461,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1256,
        "output_tokens": 828,
        "total_tokens": 2084,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 461,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the Red Inverter\n\n**I largely agree with the answer**, though I'd add some important nuances about terminology.\n\n## What the Red Inverter Actually Does\n\nThe red inverter acts as a **weak keeper** (sometimes called a \"half-latch\"), and yes, it does form a **back-to-back inverter pair** with Inv1. Here's how:\n\n### Operation:\n\n**When CK is HIGH:**\n- The left transmission gate is closed (conducting)\n- Input data enters and drives Inv1's input node\n- The weak red inverter tries to fight this, but is easily overpowered\n- New data is captured\n\n**When CK is LOW:**\n- The left transmission gate opens (non-conducting)  \n- Inv1's input node would normally float and leak charge\n- The red inverter + Inv1 now form a **static latch** (cross-coupled inverters)\n- This actively maintains the stored state indefinitely\n\n## On the Terminology\n\nCalling it a \"cross-coupled latch\" is *technically correct* but with a caveat: the red inverter is intentionally **much weaker** than Inv1 (typically 1/10th the drive strength). This asymmetry is crucial - it allows the latch to be overwritten when needed while still providing stable storage.\n\n## Minimum Clock Frequency\n\n**Yes, this absolutely removes the minimum clock frequency requirement:**\n\n- **Without keeper:** Dynamic storage via floating capacitance → leakage → requires periodic refresh → minimum f_clock\n- **With keeper:** Static storage via active feedback → no leakage concern → can hold indefinitely (DC operation)\n\n## Additional Benefits\n\nThe keeper also improves **noise immunity** on the storage node, preventing glitches from corrupting the stored bit.\n\n---\n\n**Verdict:** The answer is correct. This is a standard technique in static vs. dynamic register design.",
        "format": "markdown",
        "sha256": "5ab307b530d394e11680c5ec4d114d3dc3c0ab62e04427270dd099b279539558"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer repeats the central misconception: the red inverter is not cross-coupled with Inv1 and is not a keeper. It is an unclocked feedforward branch that can help at high speeds but overpower the latch path at low speeds, raising the minimum usable clock frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 4725,
        "total_tokens": 6033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4293,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 4725,
        "total_tokens": 6033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4293,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the Answer\n\nI **partially agree** with the quoted answer, but there's an important technical inaccuracy.\n\n## What's Correct:\n1. ✅ **Keeper function**: The red inverter does act as a keeper\n2. ✅ **Leakage protection**: It does help address leakage issues\n3. ✅ **Removes minimum frequency requirement**: This is correct\n\n## What's Misleading:\n❌ **\"Cross-coupled latch with Inv1\"** - This is **not accurate terminology**\n\n## Actual Role of the Red Inverter:\n\nThe red inverter is a **weak keeper** (or weak feedback holder), not a cross-coupled latch:\n\n### How it works:\n- **When CK = 1**: The transmission gate is closed, allowing new data to pass through. The input signal overpowers the weak red inverter and updates the node.\n\n- **When CK = 0**: The transmission gate is open, and the node at Inv1's input would float in high-impedance. The red inverter **maintains/holds** the previous logic level, preventing it from being corrupted by leakage currents.\n\n### Why \"cross-coupled latch\" is wrong:\n- A true **cross-coupled latch** has two gates with outputs feeding each other's inputs (like in an SR latch)\n- This circuit has a **single inverter in feedback** - that's just a keeper/holder circuit\n- It's also called a \"half-latch\" or \"weak feedback inverter\"\n\n### The significance:\nThe keeper must be **sized weak enough** so that valid input signals can overpower it, but **strong enough** to combat leakage currents. This is why it successfully eliminates minimum clock frequency requirements in dynamic circuits.",
        "format": "markdown",
        "sha256": "dc87f1cdd277ec151160b530a49c34a6a4af6fad4ee2f2af4af42c6f72c1841e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer repeats the incorrect keeper interpretation and claims the branch removes the minimum-frequency limit. The red inverter is instead an unclocked feedforward path that can speed high-rate operation but overpower the intended latch behavior at low rates, raising the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 2300,
        "total_tokens": 3608,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1889,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 2300,
        "total_tokens": 3608,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1889,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Analysis of the Answer\n\nI **mostly agree** with the answer, but let me clarify some important details.\n\n## What the Red Inverter Actually Does\n\nThe answer is essentially **correct**. The red inverter serves as a **weak keeper** (or half-latch) that:\n\n1. **Forms a bistable loop** with Inv1 (two inverters in feedback create a stable latch)\n2. **Maintains the charge** at the input node of Inv1 when CK is low\n3. **Prevents leakage** from corrupting the stored value\n\n## How It Works\n\n**When CK is HIGH:**\n- First transmission gate (TG) is ON → input can write to Inv1\n- The keeper is **sized weak** so it can be overpowered by the input signal\n- New data is sampled\n\n**When CK is LOW:**\n- First TG is OFF → input of Inv1 would otherwise float\n- The **weak keeper actively drives** this node, compensating for leakage currents\n- State is preserved indefinitely\n\n## Minor Terminology Note\n\nWhile \"cross-coupled latch\" is technically correct, the more common industry term is:\n- **\"Weak keeper\"** or **\"keeper circuit\"**\n- \"Cross-coupled latch\" often implies equal-strength gates (like in SRAM)\n- Here, the keeper must be **deliberately weak** (smaller transistors) to be overpowered during sampling\n\n## Bottom Line\n\n**Yes, the answer is correct.** Without this keeper, the circuit would be pure dynamic logic requiring frequent clock transitions to refresh the charge. The keeper converts it to **pseudo-static logic** with no minimum clock frequency requirement.",
        "format": "markdown",
        "sha256": "eca0215209574d81c1a77b6ae08900aad467a15da8b1e14dcf1ec8691eb2eb6f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer repeats the mistaken keeper/cross-coupled-latch interpretation. The red inverter is an unclocked feedforward branch that can help at high speed but overpower the intended latch behavior at low clock rates, raising the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 2070,
        "total_tokens": 3378,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1682,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1308,
        "output_tokens": 2070,
        "total_tokens": 3378,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1682,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Optimizing Noise Figure with Rin = 50Ω Constraint\n\nThis is a **shunt-feedback amplifier** configuration. The key to optimization lies in understanding the relationship between input impedance and noise figure.\n\n## Input Impedance Relationship\n\nFor this shunt feedback topology:\n\n$$R_{in} = \\frac{R_F}{1 + A_{OL}}$$\n\nwhere $A_{OL}$ is the open-loop gain (approximately $g_{m1} \\cdot R_L$, with $R_L$ being the load seen at M1's drain).\n\n## Optimization Strategy\n\nTo minimize NF while maintaining Rin = 50Ω:\n\n### 1. **Increase the Open-Loop Gain ($A_{OL}$)**\n\n- Higher gain allows larger $R_F$ for the same $R_{in}$\n- Larger $R_F$ reduces its thermal noise contribution: $\\overline{i_n^2} = 4kT/R_F$\n\n### 2. **Increase $g_{m1}$ of Input Transistor M1**\n\nThis is the primary optimization method:\n\n- **Increase W/L ratio** of M1\n- **Increase bias current** $I_{D1}$ \n- Higher $g_{m1}$ improves:\n  - Open-loop gain → enables larger $R_F$\n  - Signal-to-noise ratio\n  - Reduces relative transistor noise contribution\n\n### 3. **Optimize RF Value**\n\n$$R_F = 50(1 + A_{OL})$$\n\nAs you increase $A_{OL}$, increase $R_F$ proportionally to maintain the 50Ω constraint.\n\n### 4. **Additional Considerations**\n\n- **M2 sizing**: Ensure M2 (common-gate stage) provides adequate impedance and doesn't limit gain\n- **Bias point**: Optimize $I_{D1}$ for minimum noise (balance between $g_m$ and power)\n- **Bandwidth trade-off**: Larger M1 increases capacitances; may need to consider frequency response\n\n## Summary\n\n**The key is to maximize $g_{m1}$ (and thus $A_{OL}$), which allows you to use a larger $R_F$ while maintaining the 50Ω input impedance—both effects reduce the overall noise figure.**",
        "format": "markdown",
        "sha256": "f0c16efded775975a785fe38b738347a8904e8b0cd177a635e5887897af15acd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The recommendation to increase transconductance and raise RF to preserve the 50-ohm match is directionally correct. However, it omits the finite-output-resistance relation that explains why gm can exceed 1/Rs and NF fall below 1 + gamma, and incorrectly describes M2 as a common-gate stage rather than part of the CMOS inverter.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 1749,
        "total_tokens": 3367,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1188,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 1749,
        "total_tokens": 3367,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1188,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this **common-gate (CG) amplifier with resistive feedback**, here's how to optimize the noise figure (NF) while maintaining Rin = 50Ω:\n\n## Optimization Strategy\n\n### 1. **Understand the Trade-offs**\n\nFor a CG amplifier, the noise factor is:\n$$F = 1 + \\gamma g_{m1} R_S$$\n\nwhere:\n- γ ≈ 2/3 (channel noise coefficient)\n- g_{m1} is the transconductance of M₁  \n- R_S = 50Ω (source resistance)\n\nThe input resistance is:\n$$R_{in} = \\frac{1}{g_{m1}} + \\frac{R_F}{1 + A_v}$$\n\n### 2. **Optimal Configuration**\n\nTo minimize NF while maintaining Rin = 50Ω:\n\n**Primary approach:**\n- **Set g_{m1} = 1/50Ω = 20 mS**\n  - This directly provides Rin = 50Ω matching\n  - Achieves minimum NF = 1 + γ ≈ **2.2 dB** (theoretical minimum for CG)\n\n**How to achieve this:**\n- Increase the width (W) of M₁\n- Optimize the bias current I_D\n- Choose appropriate W/L ratio to get gm = 20 mS at reasonable current\n\n**Handle R_F:**\n- **Make R_F as large as possible** (or eliminate it if not needed)\n- Large R_F minimizes its thermal noise contribution (4kT/RF)\n- If RF is only for DC biasing, use R_F >> 1kΩ\n\n### 3. **Why This Works**\n\n- When gm₁R_S = 1, the noise contribution from M₁ is minimized\n- Any deviation increases the noise factor\n- R_F adds thermal noise, so minimizing its influence improves NF\n- In matched condition (1/gm = RS), you achieve the fundamental CG noise limit\n\n### 4. **Practical Implementation**\n\n✓ Increase M₁ size to boost gm without excessive current\n✓ Use minimum channel length (within stability limits)  \n✓ Consider removing RF entirely if alternative DC biasing is available\n✓ Ensure M₁ operates in saturation with adequate overdrive\n\n**Result:** NF ≈ 2.2 dB at Rin = 50Ω (best achievable for basic CG topology)",
        "format": "markdown",
        "sha256": "245ce36d5390b91a3c4f27795e58b53f3055f4b1a80f667b5ef9278e1eed937e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It misidentifies the inverter shunt-feedback LNA as a common-gate amplifier and fixes gm at 1/Rs, concluding NF cannot beat 1 + γ. It misses the finite-output-resistance mechanism: raise gm above 1/Rs and adjust RF to preserve the 50 Ω match. Recommending a very large or removed RF also conflicts with the required feedback matching.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 9995,
        "total_tokens": 11613,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9383,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 9995,
        "total_tokens": 11613,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9383,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Optimizing Noise Figure with Fixed Rin = 50Ω\n\nThis circuit is a **shunt-shunt (resistive) feedback amplifier** where RF provides feedback from the output to the input. Here's how to optimize the noise figure (NF):\n\n## Key Relationships\n\nFor this topology, the input resistance is:\n$$R_{in} = \\frac{R_F}{1 + A_v} \\approx \\frac{R_F}{A_v} \\text{ (for large gain)}$$\n\nwhere $A_v$ is the voltage gain.\n\n## Optimization Strategy\n\nTo minimize NF while maintaining **Rin = 50Ω**:\n\n### 1. **Increase RF (Feedback Resistor)**\n- Larger RF → lower thermal noise contribution to NF\n- RF's noise contribution is proportional to $\\frac{R_S}{R_F}$ where RS = 50Ω\n- Making RF >> RS significantly reduces this term\n\n### 2. **Increase Loop Gain Proportionally**\n- Since $R_{in} = R_F/(1+A_v)$ must stay at 50Ω\n- If RF increases, the gain must increase proportionally\n- This maintains the input matching while improving NF\n\n### 3. **Increase gm of M1**\n- Larger transconductance reduces M1's noise contribution: $F_{M1} \\propto \\frac{\\gamma}{g_m R_S}$\n- Achieve this by:\n  - **Increasing W/L ratio** of M1 (more effective)\n  - **Increasing bias current ID** (since $g_m \\propto \\sqrt{I_D}$)\n\n### 4. **Optimize M1 Device Size**\n- Larger width W reduces channel noise\n- Trade-off: increased capacitance affects bandwidth\n\n## Summary\n\n**The optimal approach:** Simultaneously increase both RF and the amplifier's voltage gain (by increasing gm1) such that their ratio maintains Rin = 50Ω. This minimizes both the feedback resistor and transistor noise contributions to the overall NF.\n\n**Practical implementation:** Increase M1's width and/or bias current to boost gm, and proportionally increase RF.",
        "format": "markdown",
        "sha256": "a61ddcd17c8ba05dced739406cdd95fbb04ec8de58ea44a9bae65a03a8c5a2f5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The recommendation to increase gm and RF together while maintaining Rin = 50 Ω is directionally correct and captures the design consequence. However, it uses the approximate RF/(1+Av) relation and omits the finite-output-resistance mechanism that allows gm to exceed 1/Rs and NF to fall below 1 + γ.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 3436,
        "total_tokens": 5054,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2906,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1618,
        "output_tokens": 3436,
        "total_tokens": 5054,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2906,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Input Impedance Analysis\n\nLooking at this feedback amplifier circuit, I need to find the input impedance seen by the current source $I_{in}$.\n\n## Circuit Structure\n\nThe circuit consists of:\n- **Input stage**: $M_1$ (common-source amplifier) with load $R_{D1}$\n- **Output stage**: $M_2$-$M_3$ differential pair with current source $I_{SS}$\n- **Feedback**: Resistor $R_F$ connecting output to input\n- **Input network**: $R_{in}$ and $C_{in}$ in parallel\n\n## Input Impedance Calculation\n\nThe input impedance consists of three parallel components:\n\n1. **$R_{in}$**: Input resistor\n2. **$C_{in}$**: Input capacitor (impedance = $1/sC_{in}$)\n3. **Miller impedance of $R_F$**: $\\frac{R_F}{1-A_v}$\n\nThe Miller impedance accounts for the feedback resistor $R_F$ between input and output.\n\n### General Expression\n\n$$\\boxed{Z_{in}(s) = R_{in} \\parallel \\frac{1}{sC_{in}} \\parallel \\frac{R_F}{1-A_v}}$$\n\nOr in admittance form:\n\n$$\\boxed{Z_{in}(s) = \\frac{1}{\\frac{1}{R_{in}} + sC_{in} + \\frac{1-A_v}{R_F}}}$$\n\nwhere:\n- $s = j\\omega$ (frequency domain variable)\n- $A_v = \\frac{V_{out}}{V_P}$ is the voltage gain from gate of $M_1$ to output\n\n### Voltage Gain\n\nThe overall voltage gain (negative, indicating inversion) is approximately:\n$$A_v \\approx -g_{m1}R_{D1} \\cdot g_{m2}R_{D2}$$\n\nFor large gain magnitude: $1 - A_v \\approx 1 + |A_v| \\approx |A_v|$\n\n### Simplified Expression (High Gain)\n\n$$\\boxed{Z_{in}(s) \\approx \\frac{1}{\\frac{1}{R_{in}} + sC_{in} + \\frac{|A_v|}{R_F}}}$$\n\nThe feedback significantly **reduces** the input impedance, making it approximately $R_F/|A_v|$ in parallel with $R_{in}$ (for resistive part).",
        "format": "markdown",
        "sha256": "607fb95b01dc9962d7b33d5f67a27f1da839546196ef7a7ef5f64de902b1b30a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes the Miller-feedback mechanism and the low-input-impedance trend, but misses the exact result: the numerator must include the output resistance, giving (R_F + R_D2)/(1 + A_0). Its gain approximation also omits the specified differential-stage factor, and the added R_in and C_in terms do not answer the stated model.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5537,
        "total_tokens": 5787,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5537,
        "total_tokens": 5787,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Input Impedance Calculation\n\nLooking at this circuit, I can see it's a feedback amplifier with:\n- Input components: $C_{in}$ and $R_{in}$ in parallel to ground\n- A feedback resistor $R_F$ connecting output to input (node P)\n- An amplifier core with transistors $M_1$, $M_2$, $M_3$\n\n## Analysis\n\nAt the input node P, I need to account for:\n1. Resistor $R_{in}$ to ground\n2. Capacitor $C_{in}$ to ground\n3. Feedback resistor $R_F$ (subject to Miller effect)\n4. Gate of $M_1$ (infinite impedance for ideal MOSFET)\n\n### Applying Miller's Theorem\n\nFor the feedback resistor $R_F$ connecting input to output:\n\nThe current through $R_F$ is:\n$$i_F = \\frac{V_P - V_{out}}{R_F} = \\frac{V_P(1-A_v)}{R_F}$$\n\nwhere $A_v = \\frac{V_{out}}{V_P}$ is the voltage gain.\n\nThe Miller impedance seen at the input is:\n$$Z_{Miller} = \\frac{R_F}{1-A_v}$$\n\n### Complete Input Impedance\n\nThe total input impedance is the parallel combination:\n\n$$\\boxed{Z_{in}(s) = R_{in} \\parallel \\frac{R_F}{1-A_v} \\parallel \\frac{1}{sC_{in}}}$$\n\n**In admittance form:**\n\n$$\\boxed{Z_{in}(s) = \\frac{1}{\\dfrac{1}{R_{in}} + \\dfrac{1-A_v}{R_F} + sC_{in}}}$$\n\n### For an Inverting Amplifier\n\nIf $A_v = -A$ (where $A > 0$):\n\n$$Z_{in}(s) = \\frac{1}{\\dfrac{1}{R_{in}} + \\dfrac{1+A}{R_F} + sC_{in}}$$\n\nFor large gain $A$, the input impedance is dominated by the Miller effect and becomes quite small, which is typical for transimpedance amplifiers.",
        "format": "markdown",
        "sha256": "c20c4b06dc38fa1fad11122d420cfb633a634b0677803dfbe3146d8e547ea4cf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies Miller action through the feedback resistor and the low-input-impedance trend, but it omits the output resistance in the feedback path. The required result is (RF + RD2)/(1 + A0), not simply RF/(1 + A); the added Rin and Cin are also unsupported by the stated model.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5677,
        "total_tokens": 5927,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5122,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5677,
        "total_tokens": 5927,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5122,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Looking at this circuit, I need to find the input impedance at node P where the input current source $I_{in}$ is connected.\n\n## Circuit Analysis\n\nAt node P (the gate of M1), I can identify three parallel elements:\n1. **$C_{in}$** - input capacitor\n2. **$R_{in}$** - input resistor  \n3. **Gate of M1** - MOSFET gate terminal\n\n## Key Consideration: MOSFET Gate Impedance\n\nThe gate of a MOSFET (M1) has extremely high input impedance - ideally infinite since the gate draws essentially no current. This means the gate impedance doesn't significantly affect the parallel combination.\n\n## Feedback Effects\n\nWhile $R_F$ provides feedback from the output to the source of M1:\n- This feedback **does not** affect the input impedance at the gate\n- The gate draws no current, so feedback to the source doesn't create additional loading at the gate terminal\n- There's no Miller effect shown (no explicit gate-drain capacitance)\n\n## Input Impedance Calculation\n\nThe input impedance is the parallel combination of $R_{in}$ and $C_{in}$:\n\n$$Z_{in}(s) = R_{in} \\parallel \\frac{1}{sC_{in}} = \\frac{R_{in}}{1 + sR_{in}C_{in}}$$\n\nOr in frequency domain:\n\n$$\\boxed{Z_{in}(j\\omega) = \\frac{R_{in}}{1 + j\\omega R_{in}C_{in}}}$$\n\nThe magnitude is:\n$$|Z_{in}(j\\omega)| = \\frac{R_{in}}{\\sqrt{1 + (\\omega R_{in}C_{in})^2}}$$\n\n**Special cases:**\n- At DC (ω = 0): $Z_{in} = R_{in}$\n- At high frequency: $|Z_{in}| \\approx \\frac{1}{\\omega C_{in}}$\n- Corner frequency: $f_0 = \\frac{1}{2\\pi R_{in}C_{in}}$",
        "format": "markdown",
        "sha256": "92e56613375a7b1e9248979d5db4b4f7090f6198f88d2a23f02fd7e82f9e9098"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misses the feedback mechanism that determines the input impedance and gives an unrelated parallel-RC formula. The required result is Rin = (RF + RD2)/(1 + A0); claiming RF does not affect input impedance contradicts the central circuit behavior.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5218,
        "total_tokens": 5468,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4713,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 250,
        "output_tokens": 5218,
        "total_tokens": 5468,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4713,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Computing VCO Phase Noise from LDO Thermal Noise\n\nTo find the VCO output phase noise from LDO thermal noise, we need to trace how supply voltage noise converts to phase noise.\n\n## Key Steps:\n\n### 1. **LDO Noise Appears at VCO Supply**\nThe thermal noise spectrum **Sth** (in V²/Hz) appears at the LDO output voltage **Vout**, which supplies the VCO.\n\n### 2. **Supply Voltage Modulates VCO Frequency**\nThe VCO has a supply sensitivity (pushing factor):\n$$K_{push} = \\frac{\\partial \\omega_0}{\\partial V_{out}} \\quad \\text{[rad/s/V]}$$\n\nSupply noise Δv(t) causes frequency variations:\n$$\\Delta\\omega(t) = K_{push} \\cdot \\Delta v(t)$$\n\n### 3. **Frequency Noise Converts to Phase Noise**\nSince phase is the integral of frequency:\n$$\\Delta\\phi(t) = \\int \\Delta\\omega(t) \\, dt = K_{push} \\int \\Delta v(t) \\, dt$$\n\nIn the frequency domain, integration becomes division by j2πΔf:\n$$\\Phi(j\\Delta f) = \\frac{K_{push}}{j2\\pi\\Delta f} \\cdot V(j\\Delta f)$$\n\n### 4. **Phase Noise PSD**\nTaking the power spectral density:\n\n$$\\boxed{S_\\phi(\\Delta f) = \\left[\\frac{K_{push}}{2\\pi\\Delta f}\\right]^2 \\cdot S_{th}(\\Delta f) \\quad \\text{[rad}^2\\text{/Hz]}}$$\n\nOr in standard phase noise notation:\n\n$$\\boxed{\\mathcal{L}(\\Delta f) = \\frac{K_{push}^2 \\cdot S_{th}(\\Delta f)}{2(2\\pi\\Delta f)^2} \\quad \\text{[dBc/Hz]}}$$\n\n## Key Observations:\n\n- **1/f² dependence**: Supply noise undergoes a 1/f² transfer function, making low offset frequencies most sensitive\n- **Kpush is critical**: Lower supply sensitivity reduces phase noise\n- **Design implications**: Use low-noise LDO and minimize VCO supply sensitivity through circuit design techniques (larger tank amplitude, reduced AM-PM conversion)",
        "format": "markdown",
        "sha256": "f6355c3b24d98c48d614afd6f8fdf53c3e0e607109ad25a279f7a4093860ee28"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly derives supply-pushing conversion to phase noise with the 1/Δf² dependence and consistent angular-frequency units. It omits the circuit-specific point that supply perturbation directly affects the varactors, making Kpush closely related to KVCO; the extra AM-PM/tank-amplitude suggestions do not change the main result.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 2325,
        "total_tokens": 3955,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1739,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 2325,
        "total_tokens": 3955,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1739,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Computing VCO Phase Noise from LDO Thermal Noise\n\nTo compute the VCO output phase noise from the LDO's thermal noise spectrum **Sth**, follow this approach:\n\n## Step 1: Define Supply Pushing Factor\n\nFirst, characterize the VCO's **supply pushing factor** (Kpush), which describes how supply voltage variations affect the oscillator frequency:\n\n$$K_{push} = \\frac{\\partial \\omega_0}{\\partial V_{DD}} \\quad \\text{[rad/s/V]}$$\n\nor \n\n$$K_{push,f} = \\frac{\\partial f_0}{\\partial V_{DD}} \\quad \\text{[Hz/V]}$$\n\n## Step 2: Supply Noise to Phase Noise Conversion\n\nSupply voltage noise modulates the VCO frequency. Since phase is the integral of frequency:\n\n$$\\phi(t) = \\int \\Delta\\omega(t) \\, dt = \\int K_{push} \\cdot v_n(t) \\, dt$$\n\nIn the frequency domain, this integration introduces a **1/f relationship**:\n\n$$\\Phi(f_m) = \\frac{K_{push}}{j2\\pi f_m} \\cdot V_n(f_m)$$\n\n## Step 3: Phase Noise Spectrum\n\nThe **output phase noise power spectral density** is:\n\n$$\\boxed{S_\\phi(f_m) = \\left(\\frac{K_{push}}{2\\pi f_m}\\right)^2 \\cdot S_{th}(f_m) \\quad \\text{[rad}^2\\text{/Hz]}}$$\n\nOr in **dBc/Hz**:\n\n$$\\boxed{\\mathcal{L}(f_m) = 10\\log_{10}\\left[\\frac{1}{2}\\left(\\frac{K_{push}}{2\\pi f_m}\\right)^2 \\cdot S_{th}(f_m)\\right]}$$\n\n## Key Observations\n\n- **1/f²** rolloff: Phase noise decreases quadratically with offset frequency fm\n- Low-frequency supply noise is most problematic\n- Good LDO PSRR (at relevant offset frequencies) is critical\n- Decoupling capacitors at V_out help reduce Sth",
        "format": "markdown",
        "sha256": "8faf5d866b81628fb104ade82e0437d7132029c3cd6b8ed740206a98ec3b30d5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies supply pushing and the FM-to-phase conversion with a 1/Δf² dependence. It omits the circuit-specific insight that supply noise directly perturbs the varactors, making Kpush closely related to KVCO, so reducing KVCO reduces the conversion.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 1672,
        "total_tokens": 3302,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1124,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 1672,
        "total_tokens": 3302,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1124,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Computing VCO Output Phase Noise from LDO Thermal Noise\n\nThe conversion from LDO thermal noise to VCO phase noise involves these steps:\n\n## Step 1: Determine Supply Pushing Factor\n\nFirst, characterize the VCO's **supply sensitivity (pushing factor)**:\n\n$$K_{push} = \\frac{\\partial \\omega_0}{\\partial V_{DD}} \\quad \\text{or} \\quad \\frac{\\partial f_0}{\\partial V_{DD}}$$\n\nThis describes how the oscillation frequency changes with supply voltage variations.\n\n## Step 2: Voltage Noise → Frequency Noise\n\nThe LDO thermal noise spectrum $S_{th}$ (in V²/Hz) is converted to frequency noise:\n\n$$S_\\nu(f_m) = K_{push}^2 \\cdot S_{th} \\quad \\text{(Hz²/Hz)}$$\n\nwhere $f_m$ is the offset frequency from the carrier.\n\n## Step 3: Frequency Noise → Phase Noise\n\nSince phase is the integral of frequency ($\\phi(t) = \\int \\omega(t) \\, dt$), we have:\n\n$$S_\\phi(f_m) = \\frac{S_\\nu(f_m)}{f_m^2} = \\frac{K_{push}^2 \\cdot S_{th}}{f_m^2} \\quad \\text{(rad²/Hz)}$$\n\n## Step 4: Express in Standard Units\n\nThe single-sideband phase noise in dBc/Hz:\n\n$$\\boxed{\\mathcal{L}(f_m) = 10\\log_{10}\\left[\\frac{K_{push}^2 \\cdot S_{th}}{2f_m^2}\\right] \\quad \\text{dBc/Hz}}$$\n\n## Key Observations:\n\n- **1/f²m dependence**: Supply noise impacts close-in phase noise\n- **Minimize both**: Low $S_{th}$ (good LDO design) AND low $K_{push}$ (supply-insensitive VCO)\n- For this LC-VCO: $K_{push}$ depends on tank amplitude-to-frequency coupling and varactor supply sensitivity",
        "format": "markdown",
        "sha256": "d9d9e3191a026d5c4a450ee1d9772f513e347f18620ea017c66c8575fb425611"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly uses supply pushing and the 1/f_m² FM-to-phase-noise conversion. It misses the circuit-specific insight that the supply perturbation appears directly on the varactors, making Kpush closely related to KVCO; its design takeaway is therefore less specific than required.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 1487,
        "total_tokens": 3117,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 958,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1630,
        "output_tokens": 1487,
        "total_tokens": 3117,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 958,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Tail Capacitor CT on Phase Noise\n\nWhen adding capacitor **CT** to the tail node (P), the **phase noise is REDUCED** (improved). Here's why:\n\n## Mechanism\n\n### 1. **Tail Node as Noise Source**\n- The tail current source ISS generates noise (flicker and thermal noise)\n- This noise appears as voltage fluctuations at node P\n- Due to transistor switching and circuit asymmetries, tail noise gets **upconverted** to phase noise around the oscillation frequency ω₀\n\n### 2. **CT Acts as a Low-Pass Filter**\nAt the oscillation frequency:\n- **Impedance at node P**: $Z_P = \\frac{1}{j\\omega_0 C_T}$\n- For large CT: impedance becomes very small at ω₀\n- CT **shorts high-frequency noise** to ground\n- Voltage swing at tail node: $\\Delta V_P \\propto \\frac{1}{\\omega C_T}$ (reduced)\n\n### 3. **Reduced Noise Coupling**\n- Smaller voltage fluctuations at node P\n- Less modulation of transistor operating points\n- **Reduced conversion** of tail noise to differential phase noise\n\n## Result\n\n✅ **Phase noise improves** (lower L(Δω))\n- Most effective near carrier (close-in phase noise)\n- This is a standard technique called \"**tail filtering**\"\n\n## Trade-offs\n- May affect startup conditions\n- Requires chip area\n- Can slightly impact tuning range\n\nThis is why tail capacitors are commonly used in low-phase-noise oscillator designs.",
        "format": "markdown",
        "sha256": "a64825afaaf01ea13461cc686c45ba14cee748949fc3e5e5b0aea755d7f41580"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It gives a monotonic phase-noise improvement from tail filtering, missing the nonmonotonic effect and the class-C improvement and degradation mechanisms.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1023,
        "total_tokens": 2630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 635,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1023,
        "total_tokens": 2630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 635,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Tail Capacitor (CT) on Phase Noise\n\nWhen adding a tail capacitor **CT** to node P in this cross-coupled LC oscillator, the **phase noise improves (decreases)**, particularly at close-in offset frequencies.\n\n## Why Phase Noise Improves:\n\n### 1. **Increased Tail Node Impedance**\n- CT increases the impedance at node P at the oscillation frequency ω₀\n- Higher impedance means current noise from ISS has less effect on converting to voltage/phase noise\n\n### 2. **Low-Frequency Noise Filtering**\n- CT acts as a low-pass filter, blocking high-frequency noise components\n- **Critically**: It filters **1/f (flicker) noise** from the tail current source before it can upconvert to phase noise sidebands\n- This is the primary benefit for close-in phase noise performance\n\n### 3. **Common-Mode Noise Suppression**\n- Tail current noise appears as common-mode noise to the differential pair\n- CT provides a low-impedance path to ground for AC common-mode variations\n- Reduces the cyclostationary upconversion of tail noise\n\n## Practical Result:\n\n**Close-in phase noise** (dominated by 1/f noise upconversion) **significantly improves**\n\nThis is a common technique called **\"tail filtering\"** used in high-performance oscillator design.\n\n### Trade-offs:\n- Too large CT may affect startup or bias stability\n- Optimal CT value balances noise filtering with other performance metrics",
        "format": "markdown",
        "sha256": "4e0e914a73c3f1db52bf390045064e41ee662f6f3ff38039c50a3d67c0757efc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer claims CT monotonically improves phase noise through tail-noise and flicker-noise filtering. It misses the nonmonotonic behavior, including class-C improvement and the degradation mechanisms described in the golden solution; a generic warning about large CT is insufficient.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1203,
        "total_tokens": 2810,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 847,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1203,
        "total_tokens": 2810,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 847,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Adding CT to the Tail Node\n\nWhen a tail capacitor **CT** is added to node P (the common source node), the **phase noise decreases** (improves). Here's why:\n\n## Key Mechanisms:\n\n### 1. **Tail Current Noise Filtering**\n- CT acts as a **low-pass filter** for noise from the current source ISS\n- At the oscillation frequency (typically GHz range), CT presents low impedance to ground\n- High-frequency noise from ISS is bypassed to ground rather than being injected into the oscillator core\n\n### 2. **Common-Mode Noise Suppression**\n- Node P is a common-mode point in the differential circuit\n- CT stabilizes the tail voltage, preventing common-mode noise from converting to differential-mode noise\n- Differential-mode noise directly affects the oscillation phase, so reducing this conversion improves phase noise\n\n### 3. **Impulse Sensitivity Function (ISF) Effect**\nAccording to Hajimiri-Lee phase noise theory:\n- The tail node is most sensitive to noise when **both transistors are ON** (around voltage zero-crossings)\n- During these critical times, CT shunts noise current to ground\n- This reduces the effective noise that couples into the tank circuit\n\n## Trade-offs:\n\n⚠️ **CT should be chosen carefully:**\n- Too small → insufficient filtering\n- Too large → may affect startup, DC bias stability, or oscillation amplitude\n\n## Bottom Line:\n**Phase noise improves** (L(f) decreases in dBc/Hz), particularly by reducing the tail current source's noise contribution, which is often dominant in single-ended tail architectures.",
        "format": "markdown",
        "sha256": "8cd812255453d53181437df378e42ea78ef1d24e864f6b0bf7c0d241b9cd1f06"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It concludes that CT improves phase noise monotonically through filtering. It misses the nonmonotonic behavior and the class-C improvement and degradation mechanisms; the generic startup and bias caveats do not address phase-noise tradeoffs.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1058,
        "total_tokens": 2665,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 674,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1607,
        "output_tokens": 1058,
        "total_tokens": 2665,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 674,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Oscillation Frequency Estimation\n\n## Circuit Analysis\n\nThis is a **cross-coupled differential oscillator** with two identical stages. Each stage consists of:\n- A differential pair of transistors\n- Mechanical resonators (springs) as load elements at nodes X and Y\n- Cross-coupled feedback connections\n- Bias current sources (I_SS and I_1)\n\n## Frequency Determination\n\nFor this type of oscillator, the oscillation frequency is primarily determined by the **resonant frequency of the mechanical resonators** (springs).\n\nThe oscillation frequency is:\n\n$$f_{osc} \\approx \\frac{1}{2\\pi}\\sqrt{\\frac{k}{m_{eff}}}$$\n\nWhere:\n- k = spring constant\n- m_eff = effective mass of the resonator\n\n## Typical Frequency Range\n\nWithout specific component values, the frequency depends on the type of mechanical resonator used:\n\n| Resonator Type | Typical Frequency Range |\n|----------------|------------------------|\n| MEMS cantilever | 10 kHz - 1 MHz |\n| MEMS bulk resonator | 1 MHz - 100 MHz |\n| SAW device | 10 MHz - 1 GHz |\n| BAW device | 100 MHz - 10 GHz |\n\n**For a typical MEMS oscillator application: f ≈ 10-100 MHz**\n\nThe cross-coupled configuration provides negative resistance to sustain oscillation by compensating for mechanical damping losses in the resonators.",
        "format": "markdown",
        "sha256": "86388fb8baf908df9286523e579cf111fd70148e09421c69bec4564b4f660568"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the circuit as a mechanical-resonator oscillator and gives no LC tank-frequency estimate or coupling-induced frequency shift.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 2903,
        "total_tokens": 4519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2549,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 2903,
        "total_tokens": 4519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2549,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Oscillation Frequency Estimation\n\nThis circuit is a **cross-coupled LC differential oscillator** (also known as a negative-Gm oscillator). There are two identical stages that appear to be coupled together.\n\n## Oscillation Frequency Formula\n\nFor each LC tank oscillator stage, the oscillation frequency is determined by:\n\n$$f_0 = \\frac{1}{2\\pi\\sqrt{LC}}$$\n\nWhere:\n- **L** = inductance of the tank inductors (shown as coil symbols)\n- **C** = total capacitance at nodes x and y (including explicit capacitors and transistor parasitics)\n\n## Key Observations\n\n1. **Circuit topology**: Cross-coupled differential pair with LC tanks\n2. **Two stages**: The upper and lower stages appear coupled (suggesting possible quadrature operation with 90° phase relationship)\n3. **Tuning**: The capacitors with arrows may be varactors (variable capacitors), making this a VCO\n\n## Typical Frequency Range\n\nWithout specific component values shown, typical implementations operate at:\n\n- **Integrated CMOS** (L ≈ 1-5 nH, C ≈ 0.5-2 pF): **~2-10 GHz**\n- **Discrete RF** (larger components): **~100 MHz - 2 GHz**\n\n**To get a specific frequency estimate, the values of L and C would need to be provided.**",
        "format": "markdown",
        "sha256": "b885c24294319baa3c85752d58ec3b3b6624ae62152d473b55a45dbf198d37ef"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly gives the uncoupled LC tank resonance, but omits the key coupling-induced frequency shift, so it does not estimate the oscillation frequency of the coupled circuit.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 1326,
        "total_tokens": 2942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 989,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 1326,
        "total_tokens": 2942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 989,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "anthropic/claude-sonnet-4.5",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Oscillation Frequency Estimation\n\n## Circuit Analysis\n\nThis circuit is a **two-stage cross-coupled ring oscillator** with differential pairs. Each stage contains:\n- Cross-coupled transistor pairs\n- Inductive loads (springs symbols = inductors L)\n- Coupling capacitors\n- Current sources for biasing\n\n## Frequency Formula\n\nFor this type of cross-coupled LC oscillator, the oscillation frequency is:\n\n$$f_0 = \\frac{1}{2\\pi\\sqrt{LC}}$$\n\nWhere:\n- **L** = inductance of the load inductors\n- **C** = total capacitance at each tank node (including gate/base capacitances and coupling capacitors)\n\n## Estimation Approach\n\nWithout specific component values, the frequency depends on:\n\n1. **Load inductance (L)**: The spring elements at the top of each stage\n2. **Total capacitance (C)**: Sum of coupling capacitors, transistor input capacitances, and parasitic capacitances\n\n## Typical Ranges\n\n- **Integrated RF circuits**: L ~ 1-10 nH, C ~ 0.1-1 pF → **f ~ 1-10 GHz**\n- **Discrete circuits**: L ~ 1-100 μH, C ~ 10-100 pF → **f ~ 10-500 MHz**\n\n## Additional Factor\n\nFor a two-stage ring configuration, ensure there's sufficient phase shift (180° per stage) for sustained oscillation at frequency f₀.\n\n**To get a numerical estimate, you would need the specific values of L and C from the circuit design.**",
        "format": "markdown",
        "sha256": "ebc339b8714ab76a1a2dc2eb0559bf19edceb216c6097d0756922fa4c6925c88"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly gives the uncoupled tank resonance, but presents it as the oscillation frequency and omits the essential coupling-induced shift, approximately Δω = αω₀/(2Q). The ring-oscillator and 180°-per-stage framing does not address that mechanism.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 2200,
        "total_tokens": 3816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1825,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1616,
        "output_tokens": 2200,
        "total_tokens": 3816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1825,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    }
  ]
}
