{
  "model_key": "deepseek_v41_flash_1017",
  "display_name": "DeepSeek V4.1 Flash 1017",
  "provider": "deepseek",
  "evaluation_model_ids": [],
  "thinking_effort": "max",
  "configuration_note": "DeepSeek V4.1 Flash 1017 answered the 50 tasks in three rollouts through OpenRouter's chat completions route (deepseek/deepseek-v4.1-flash-1017) at maximum reasoning effort. Requests set max_tokens to 943,718, the model's output limit. Each request was one user message holding only the question text and its figure: no title, headings or system prompt. Answers cut off at the output limit were re-run; every attempt is counted in tokens and cost. Answers were graded by GPT-6 Luna at maximum reasoning effort. Cost uses OpenRouter's list price for DeepSeek V4.1 Flash 1017 on 2026-11-10 ($0.006 input, $0.005 cached input, $0.50 output per 1M tokens).",
  "mode": "direct_qa",
  "summary": {
    "rollout_count": 3,
    "answer_count": 150,
    "scores": {
      "overall": {
        "gpt_6_luna_max": {
          "response_count": 150,
          "correct_count": 100,
          "incorrect_count": 50,
          "partial_credit_count": 35,
          "zero_count": 15,
          "mean_score_0_to_4": 3.0933333333333333,
          "score_percent": 77.33333333333333,
          "score_distribution": {
            "0": 15,
            "1": 15,
            "2": 11,
            "3": 9,
            "4": 100
          }
        },
        "active": {
          "response_count": 150,
          "correct_count": 100,
          "incorrect_count": 50,
          "partial_credit_count": 35,
          "zero_count": 15,
          "mean_score_0_to_4": 3.0933333333333333,
          "score_percent": 77.33333333333333,
          "score_distribution": {
            "0": 15,
            "1": 15,
            "2": 11,
            "3": 9,
            "4": 100
          }
        }
      },
      "part1": {
        "gpt_6_luna_max": {
          "response_count": 90,
          "correct_count": 74,
          "incorrect_count": 16,
          "partial_credit_count": 3,
          "zero_count": 13,
          "mean_score_0_to_4": 3.3555555555555556,
          "score_percent": 83.88888888888889,
          "score_distribution": {
            "0": 13,
            "1": 1,
            "2": 1,
            "3": 1,
            "4": 74
          }
        },
        "active": {
          "response_count": 90,
          "correct_count": 74,
          "incorrect_count": 16,
          "partial_credit_count": 3,
          "zero_count": 13,
          "mean_score_0_to_4": 3.3555555555555556,
          "score_percent": 83.88888888888889,
          "score_distribution": {
            "0": 13,
            "1": 1,
            "2": 1,
            "3": 1,
            "4": 74
          }
        }
      },
      "part2": {
        "gpt_6_luna_max": {
          "response_count": 60,
          "correct_count": 26,
          "incorrect_count": 34,
          "partial_credit_count": 32,
          "zero_count": 2,
          "mean_score_0_to_4": 2.7,
          "score_percent": 67.5,
          "score_distribution": {
            "0": 2,
            "1": 14,
            "2": 10,
            "3": 8,
            "4": 26
          }
        },
        "active": {
          "response_count": 60,
          "correct_count": 26,
          "incorrect_count": 34,
          "partial_credit_count": 32,
          "zero_count": 2,
          "mean_score_0_to_4": 2.7,
          "score_percent": 67.5,
          "score_distribution": {
            "0": 2,
            "1": 14,
            "2": 10,
            "3": 8,
            "4": 26
          }
        }
      }
    },
    "by_rollout": {
      "1": {
        "response_count": 50,
        "correct_count": 35,
        "incorrect_count": 15,
        "partial_credit_count": 12,
        "zero_count": 3,
        "mean_score_0_to_4": 3.26,
        "score_percent": 81.5,
        "score_distribution": {
          "0": 3,
          "1": 5,
          "2": 3,
          "3": 4,
          "4": 35
        }
      },
      "2": {
        "response_count": 50,
        "correct_count": 35,
        "incorrect_count": 15,
        "partial_credit_count": 9,
        "zero_count": 6,
        "mean_score_0_to_4": 3.1,
        "score_percent": 77.5,
        "score_distribution": {
          "0": 6,
          "1": 5,
          "2": 2,
          "3": 2,
          "4": 35
        }
      },
      "3": {
        "response_count": 50,
        "correct_count": 30,
        "incorrect_count": 20,
        "partial_credit_count": 14,
        "zero_count": 6,
        "mean_score_0_to_4": 2.92,
        "score_percent": 73.0,
        "score_distribution": {
          "0": 6,
          "1": 5,
          "2": 6,
          "3": 3,
          "4": 30
        }
      }
    },
    "tokens": {
      "response_count": 150,
      "usage_record_count": 150,
      "complete_usage_count": 150,
      "missing_usage_count": 0,
      "missing_cached_input_count": 0,
      "complete": true,
      "totals": {
        "cached_input_tokens": 8192,
        "input_tokens": 112620,
        "output_tokens": 3831877,
        "total_tokens": 3944497
      },
      "known_totals": {
        "cached_input_tokens": 8192,
        "input_tokens": 112620,
        "output_tokens": 3831877,
        "total_tokens": 3944497
      }
    },
    "by_rollout_part": {
      "part1": {
        "1": {
          "response_count": 30,
          "correct_count": 26,
          "incorrect_count": 4,
          "partial_credit_count": 1,
          "zero_count": 3,
          "mean_score_0_to_4": 3.566666666666667,
          "score_percent": 89.16666666666667,
          "score_distribution": {
            "0": 3,
            "3": 1,
            "4": 26
          }
        },
        "2": {
          "response_count": 30,
          "correct_count": 25,
          "incorrect_count": 5,
          "partial_credit_count": 0,
          "zero_count": 5,
          "mean_score_0_to_4": 3.3333333333333335,
          "score_percent": 83.33333333333334,
          "score_distribution": {
            "0": 5,
            "4": 25
          }
        },
        "3": {
          "response_count": 30,
          "correct_count": 23,
          "incorrect_count": 7,
          "partial_credit_count": 2,
          "zero_count": 5,
          "mean_score_0_to_4": 3.1666666666666665,
          "score_percent": 79.16666666666666,
          "score_distribution": {
            "0": 5,
            "1": 1,
            "2": 1,
            "4": 23
          }
        }
      },
      "part2": {
        "1": {
          "response_count": 20,
          "correct_count": 9,
          "incorrect_count": 11,
          "partial_credit_count": 11,
          "zero_count": 0,
          "mean_score_0_to_4": 2.8,
          "score_percent": 70.0,
          "score_distribution": {
            "1": 5,
            "2": 3,
            "3": 3,
            "4": 9
          }
        },
        "2": {
          "response_count": 20,
          "correct_count": 10,
          "incorrect_count": 10,
          "partial_credit_count": 9,
          "zero_count": 1,
          "mean_score_0_to_4": 2.75,
          "score_percent": 68.75,
          "score_distribution": {
            "0": 1,
            "1": 5,
            "2": 2,
            "3": 2,
            "4": 10
          }
        },
        "3": {
          "response_count": 20,
          "correct_count": 7,
          "incorrect_count": 13,
          "partial_credit_count": 12,
          "zero_count": 1,
          "mean_score_0_to_4": 2.55,
          "score_percent": 63.74999999999999,
          "score_distribution": {
            "0": 1,
            "1": 4,
            "2": 5,
            "3": 3,
            "4": 7
          }
        }
      }
    }
  },
  "answers": [
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Intrinsic gain is\n\n\\[\nA_{\\text{int}}=\\frac{g_m}{g_{ds}}=g_m r_o .\n\\]\n\nIn the usual square-law saturation model,\n\n\\[\ng_m \\approx \\frac{2I_D}{V_{ov}},\\qquad\ng_{ds}\\approx \\lambda I_D,\\qquad\nA_{\\text{int}}\\approx \\frac{2}{\\lambda V_{ov}} .\n\\]\n\nIf both \\(W\\) and \\(L\\) are doubled while keeping the same bias/current, the ratio \\(W/L\\) stays the same, so \\(g_m\\) is roughly unchanged. The longer channel, however, increases the output resistance approximately as \\(r_o\\propto L\\) because \\(\\lambda\\sim 1/L\\) in long-channel devices. Hence\n\n\\[\nA_{\\text{int}} \\approx \\text{about }2\\times \\text{ larger}\\quad (\\approx +6\\text{ dB}).\n\\]\n\nThe width increase by itself does not improve intrinsic gain in this ideal picture; the improvement comes from the longer channel.\n\nCaveat: If you use the simplest model where the channel-length-modulation parameter \\(\\lambda\\) is treated as independent of \\(L\\), the predicted gain is unchanged because \\(W/L\\) is unchanged. In short-channel devices, the actual increase is usually less than \\(2\\times\\) and depends on bias and short-channel effects.",
        "format": "markdown",
        "sha256": "517027ad21117adc28d6730a28931e71dd7e88f93022b145f341086b91e79960"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that doubling both dimensions preserves W/L and approximately gm, while the longer channel reduces λ and increases ro by about 2×, so intrinsic gain roughly doubles. The model and short-channel caveats are reasonable qualifications.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 9787,
        "total_tokens": 9835,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8667,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 9787,
        "total_tokens": 9835,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8667,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For a MOSFET in saturation, the intrinsic gain is\n\n\\[\nA_{\\rm int}=|g_m/g_{ds}|=g_m r_o .\n\\]\n\nUsing the usual long-channel saturation model,\n\n\\[\ng_m=\\frac{2I_D}{V_{OV}},\\qquad\nr_o \\approx \\frac{V_A' L}{I_D}\\quad\\left(\\lambda\\propto \\frac1L\\right),\n\\]\n\nso\n\n\\[\nA_{\\rm int}\\approx \\frac{2V_A' L}{V_{OV}} .\n\\]\n\nThus:\n\n- **Width alone does not set the intrinsic gain** if the current density/overdrive is fixed; \\(W\\) cancels out.\n- If you **double both \\(L\\) and \\(W\\)** while keeping \\(W/L\\) constant and bias the device at the same overdrive/current density, \\(g_m\\) stays essentially unchanged and \\(r_o\\) roughly doubles. Hence the intrinsic gain **roughly doubles** in a long-channel model.\n- In a very simple model that treats the channel-length-modulation parameter \\(\\lambda\\) as fixed independent of \\(L\\), the gain appears unchanged. In modern short-channel devices, the increase is usually **less than 2×** and is process/bias dependent.\n\nSo the standard answer is: **preserving \\(W/L\\) and bias, doubling both \\(W\\) and \\(L\\) approximately doubles the intrinsic gain; width by itself has little/effect no effect, while longer channel length increases gain.**",
        "format": "markdown",
        "sha256": "843257b6a66ac5ee29a763dfcbc9a65ad67a53b11fd78e77b0e7ac7b96f172d0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that doubling both dimensions at fixed overdrive leaves gm and current approximately unchanged, while the longer channel roughly doubles ro and intrinsic gain. The stated bias and model caveats are appropriate.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 9853,
        "total_tokens": 9901,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 9853,
        "total_tokens": 9901,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The intrinsic gain is \\(A_{\\text{int}} = g_m/g_{ds} = g_m r_o\\).\n\nIf both \\(W\\) and \\(L\\) are doubled while keeping \\(W/L\\) constant and keeping the same bias/overdrive:\n\n- \\(g_m\\) stays approximately the same, since \\(g_m \\propto W/L\\).\n- The channel-length-modulation parameter \\(\\lambda\\) is usually modeled as \\(\\lambda \\propto 1/L\\). Thus \\(g_{ds} = I_D\\lambda\\) decreases by about \\(2\\times\\), so \\(r_o = 1/g_{ds}\\) doubles.\n\nTherefore,\n\n\\[\nA_{\\text{int}} \\approx \\frac{g_m}{g_{ds}} \\propto L\n\\]\n\nso the intrinsic gain approximately **doubles** when \\(L\\) (and \\(W\\)) is doubled.\n\nCaveat: in a simplified model that treats \\(\\lambda\\) as a constant or ignores channel-length modulation, the intrinsic gain would be unchanged (or ideally infinite).",
        "format": "markdown",
        "sha256": "c5dd76ef83ac94e08bebbb985a4ca7d1406df70fdeba0a0e139eeadb773d7abc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that keeping W/L and overdrive fixed leaves gm and current approximately unchanged, while doubling L reduces channel-length modulation and doubles ro, so intrinsic gain approximately doubles. The caveat is consistent with alternative model assumptions.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 6237,
        "total_tokens": 6285,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6028,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 48,
        "output_tokens": 6237,
        "total_tokens": 6285,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6028,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "It depends on what is held constant.\n\n- For a long-channel MOSFET in saturation with the device dimensions fixed, **Student A is correct**:\n  \\[\n  I_D=\\frac12 k_n' \\frac{W}{L}(V_{GS}-V_{TH})^2\n  \\]\n  \\[\n  g_m=\\frac{\\partial I_D}{\\partial V_{GS}}\n      = k_n' \\frac{W}{L}(V_{GS}-V_{TH})\n      = k_n' \\frac{W}{L}V_{OV}\n  \\]\n  So \\(g_m\\) increases with overdrive \\(V_{OV}\\) when \\(W/L\\) and \\(V_{DS}\\) are fixed.\n\n- However, if the drain current is held constant, then\n  \\[\n  g_m=\\frac{2I_D}{V_{OV}}.\n  \\]\n  In that case, increasing \\(V_{OV}\\) requires reducing \\(W/L\\), and \\(g_m\\) decreases with overdrive. Then **Student B is correct**.\n\nSo: **A is correct under the usual “same transistor, increasing gate bias” interpretation; B is correct for a fixed drain current.** In short-channel devices the dependence also tends to flatten because of velocity saturation.",
        "format": "markdown",
        "sha256": "c9371b1325442205fcc592319008af53477409363537f078bedb42bb881bb015"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed device, explains that gm rises with VOV, and states the fixed-ID condition under which Student B is right.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 4347,
        "total_tokens": 4407,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4090,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 4347,
        "total_tokens": 4407,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4090,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Neither is unconditionally correct; it depends on what is held constant.\n\nFor a long-channel MOSFET in strong-inversion saturation, with  \n\\[\nV_{OV}=V_{GS}-V_T,\\qquad \nI_D\\approx \\frac12 \\beta V_{OV}^2,\\quad \\beta=\\mu C_{ox}\\frac WL,\n\\]\nthe small-signal transconductance is\n\\[\ng_m=\\frac{\\partial I_D}{\\partial V_{GS}}\n=\\beta V_{OV}\n=\\sqrt{2\\beta I_D}\n=\\frac{2I_D}{V_{OV}}.\n\\]\n\n- If the transistor geometry is fixed and you increase overdrive by increasing \\(V_{GS}\\), then \\(g_m\\) increases linearly with \\(V_{OV}\\). In this standard textbook sense, **Student A is correct**.\n- If drain current is held fixed and overdrive is changed by changing device size/bias, then \\(g_m=2I_D/V_{OV}\\), so a larger \\(V_{OV}\\) gives a smaller \\(g_m\\). In that comparison, **Student B is correct**. What decreases very clearly is the transconductance efficiency \\(g_m/I_D\\approx 2/V_{OV}\\).\n\nIn short-channel devices, velocity saturation and mobility degradation can make \\(g_m\\) level off or eventually degrade, so neither simple statement holds over the entire range.\n\nSo: **A for a fixed-geometry bias sweep; B for a fixed-current comparison or \\(g_m/I_D\\).**",
        "format": "markdown",
        "sha256": "185d897bdaec5539f999cd4102ad516cd50a0e7b8a12b32448dbf4eabd3b9e3b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed transistor geometry and explains that increasing overdrive raises gm. The fixed-current comparison and short-channel caveat do not undermine the central answer.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 10068,
        "total_tokens": 10128,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9760,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 10068,
        "total_tokens": 10128,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9760,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Both can be right; it depends on what is held constant.\n\nFor a long-channel MOSFET in saturation,\n\\[\nV_{OV}=V_{GS}-V_{TH},\\qquad\nI_D=\\frac12 \\mu C_{ox}\\frac{W}{L}V_{OV}^2,\n\\]\n\\[\ng_m=\\frac{\\partial I_D}{\\partial V_{GS}}\n= \\mu C_{ox}\\frac{W}{L}V_{OV}\n= \\sqrt{2\\mu C_{ox}\\frac{W}{L}I_D}\n= \\frac{2I_D}{V_{OV}}.\n\\]\n\n- If you increase \\(V_{OV}\\) by increasing \\(V_{GS}\\) with the same device size \\(W/L\\), then \\(g_m\\) increases approximately linearly with \\(V_{OV}\\). Under this usual textbook interpretation, Student A is correct.\n- If the drain current \\(I_D\\) is held fixed and you increase \\(V_{OV}\\) by reducing \\(W/L\\) or moving to stronger inversion, then\n  \\[\n  g_m=\\frac{2I_D}{V_{OV}}\n  \\]\n  decreases. Under this fixed-current design interpretation, Student B is correct.\n\nIn short-channel devices with velocity saturation, \\(g_m\\) may flatten and become nearly independent of overdrive rather than continuing to rise.\n\nSo the precise answer is: **neither statement is universally true without specifying the bias condition. For a fixed device biased by increasing \\(V_{GS}\\), A is right; for a fixed drain current, B is right.**",
        "format": "markdown",
        "sha256": "d69279b233526f1f29c7a88eebbb758ac8e210632c7af51c04576cbb12c2b7ab"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that for a fixed device size, increasing overdrive raises gm, and explains the fixed-current condition under which Student B is right. The secondary short-channel note does not alter the essential answer.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 5212,
        "total_tokens": 5272,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4894,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 60,
        "output_tokens": 5212,
        "total_tokens": 5272,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4894,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Not literally—but the **intrinsic small-signal equivalent circuit has the same topology** for NMOS and PMOS.\n\nAt a given dc operating point, if you define \\(i_d\\) positive into the drain and use the same terminal-voltage definitions,\n\\[\nv_{gs}=v_g-v_s,\\qquad v_{ds}=v_d-v_s,\\qquad v_{bs}=v_b-v_s,\n\\]\nthen in saturation both devices can be modeled as\n\\[\ni_d=g_m v_{gs}+g_{mb}v_{bs}+g_{ds}v_{ds}\n\\]\nplus the capacitances \\(C_{gs}\\), \\(C_{gd}\\), \\(C_{db}\\), \\(C_{sb}\\), etc., and output resistance \\(r_o=1/g_{ds}\\).\n\nWhat differs:\n\n- PMOS bias polarity is reversed: it is on for \\(V_{GS}<V_{TP}<0\\), its source is normally the higher-potential terminal, and its bulk is tied to the high rail; NMOS source is normally lower and bulk to ground.\n- The numerical parameters differ: \\(\\mu_p\\neq\\mu_n\\), thresholds and body-effect coefficients differ, and pMOS devices often need larger \\(W/L\\) for the same \\(g_m\\).\n- If you use the common PMOS variables \\(v_{sg}\\), \\(v_{sd}\\), or current from source to drain, all controlled-source/current polarities are reversed. Equivalently, flip the source/drain orientation and reverse voltage/current arrows.\n- A full high-frequency/IC model may include n-well/well-to-substrate parasitics not present identically in an NMOS.\n\nSo: **same small-signal model form after applying the correct polarity conventions and using the correct device parameters; not identical in bias, signs, or numerical values.** For most hand analyses with the source at small-signal ground and using positive \\(g_m,r_o\\), the usual \\(g_mv_{gs}\\) and \\(r_o\\) model is drawn the same for both.",
        "format": "markdown",
        "sha256": "ac92c9dc06c6a01c34136d96b01da238917ba1cb785918c8a89dc313cc10e382"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form as the NMOS model after applying consistent polarity conventions.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 12269,
        "total_tokens": 12319,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11350,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 12269,
        "total_tokens": 12319,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11350,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**In form: yes; literally/sign-wise: no—you must account for the reversed polarities and source/drain roles.**\n\nFor a MOSFET in saturation, the small-signal hybrid-π model has the same topology for both types:\n\n\\[\ni_d=g_m v_{gs}+g_{mb}v_{bs}+\\frac{v_{ds}}{r_o}\n\\]\n\nplus the capacitors \\(C_{gs}\\), \\(C_{gd}\\), \\(C_{sb}\\), \\(C_{db}\\). The gate is isolated at low frequency.\n\nFor a PMOS, using p-channel reference directions,\n\n\\[\ni_{sd}=g_m v_{sg}+g_{mb}v_{sb}+\\frac{v_{sd}}{r_o}\n\\]\n\n(up to the sign convention used for the body term). This is the NMOS model with **source and drain interchanged/rotated** and the DC voltage/current polarities reversed.\n\nKey differences:\n- NMOS: \\(V_{GS}>V_{TN}>0\\), normal current flows drain→source.\n- PMOS: \\(V_{GS}<V_{TP}<0\\) or \\(V_{SG}>|V_{TP}|\\), normal current flows source→drain.\n- PMOS body is usually tied to the positive rail/n-well; NMOS body to the negative rail/substrate.\n- In a drawn schematic, the controlled-source arrow for a PMOS often appears opposite to that of an NMOS because the PMOS is normally drawn with its source at the positive supply.\n- The parameter values are not generally equal for the same \\(W/L\\): \\(\\mu_p\\neq\\mu_n\\), thresholds, \\(V_A/\\lambda\\), junction/well capacitances, and body connections differ. Equal small-signal models are possible with suitable sizing and bias.\n\nSo: **same equivalent-circuit topology and same equations under consistent PMOS polarities; not a blind drop-in replacement without flipping source/drain and sign conventions.**",
        "format": "markdown",
        "sha256": "bc4b3a0979fbdabf0f08a435063625740642746a50d8aa4d4d194e9c9ad7153b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form as the NMOS model under consistent polarity conventions; the added explanation is consistent with the golden solution.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 22940,
        "total_tokens": 22990,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 22940,
        "total_tokens": 22990,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Short answer: **The small-signal equivalent circuit is essentially the same, but the sign conventions and numerical parameter values are not literally identical.** A PMOS can be treated just like an NMOS if you use \\(v_{SG}\\) instead of \\(v_{GS}\\) and choose the current arrow in the direction of normal PMOS current.\n\nFor saturation, low frequency, body tied to source:\n\n- NMOS:\n\\[\ni_{ds}=g_m v_{gs}+\\frac{v_{ds}}{r_o},\n\\qquad\nv_{gs}=v_g-v_s,\\quad v_{ds}=v_d-v_s\n\\]\n\n- PMOS:\n\\[\ni_{sd}=g_m v_{sg}+\\frac{v_{sd}}{r_o},\n\\qquad\nv_{sg}=v_s-v_g,\\quad v_{sd}=v_s-v_d\n\\]\n\nThese have the **same form** after relabeling the controlling voltage and current direction. If instead you use \\(v_{gs}=v_g-v_s\\) for the PMOS while keeping the source-to-drain current arrow, you get a minus sign:\n\\[\ni_{sd}=-g_m v_{gs}-\\frac{v_{ds}}{r_o}.\n\\]\nThis is just a polarity/arrow convention; it does not mean a different small-signal topology.\n\nAt higher frequencies, both use the same topology with \\(C_{gs}\\), \\(C_{gd}\\), drain/body/source junction capacitances, and a body-effect source \\(g_{mb}v_{bs}\\). The capacitance values and body connections differ because a PMOS has an n-well body, usually tied to \\(V_{DD}\\), while an NMOS body is usually tied to \\(V_{SS}\\). The parameters \\(g_m\\), \\(r_o\\), and capacitances also differ because of mobility, doping, dimensions, and bias.\n\nSo: **yes in terms of the small-signal equivalent-circuit topology after choosing the proper polarity; no if “identical” means same numerical values and exactly the same signed terminal equations without reversing references.**",
        "format": "markdown",
        "sha256": "5c1cf822de4b526623413b00bb97ac6e4558b3a17751d982dcc0a17a874a6641"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly says the models have the same form after choosing consistent polarity and current conventions; the added parameter and body-connection caveats do not change the answer.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 22268,
        "total_tokens": 22318,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 50,
        "output_tokens": 22268,
        "total_tokens": 22318,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For the diode-connected NMOS transistor \\(M_1\\), the gate and drain are tied together and the source is grounded, so\n\n\\[\nV_{GS}=V_{DS}=V_X .\n\\]\n\nFor an enhancement NMOS, \\(M_1\\) is off until  \n\\[\nV_X=V_{TH}.\n\\]\nOnce \\(V_X>V_{TH}\\), it remains in saturation because \\(V_{DS}=V_{GS}>V_{GS}-V_{TH}\\). Hence\n\n\\[\nI_X = \n\\begin{cases}\n0, & V_X \\le V_{TH},\\\\[6pt]\n\\dfrac{1}{2}\\mu_n C_{ox}\\dfrac{W}{L}\\,(V_X-V_{TH})^2, \n& V_X \\ge V_{TH}.\n\\end{cases}\n\\]\n\nIncluding channel-length modulation approximately gives\n\n\\[\nI_X \\approx \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}\n(V_X-V_{TH})^2(1+\\lambda V_X),\\qquad V_X\\ge V_{TH}.\n\\]\n\nSketch:\n\n```text\n I_X\n  ^\n  |                              /\n  |                            /\n  |                          /\n  |                       . \n  |                   .\n  |             .\n  |_________ ._____________________> V_X\n             V_TH\n```\n\n- For \\(V_X<V_{TH}\\): \\(I_X=0\\).\n- At \\(V_X=V_{TH}\\): the curve starts with zero slope.\n- For \\(V_X>V_{TH}\\): \\(I_X\\) increases quadratically (parabolic, concave upward); with channel-length modulation it has a slight additional upward slope.\n\nIf the arrow for \\(I_X\\) in your figure is defined opposite to the forward drain-to-source current, reverse the sign of the curve. For a depletion-mode device, shift the starting point to the depletion threshold.",
        "format": "markdown",
        "sha256": "dae0051f1344ec2ba86b54b06b0b789f0967d28d4337cfc62c9d4951ca84c573"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, its off region and saturation above threshold, and gives the required quadratic current rise. The optional channel-length modulation and caveats do not detract.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 10806,
        "total_tokens": 11446,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 10806,
        "total_tokens": 11446,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For an n-channel enhancement MOSFET \\(M_1\\), the gate and drain are tied together, so\n\n\\[\nV_{GS}=V_{DS}=V_X.\n\\]\n\nThus:\n\n- For \\(V_X<V_T\\), the transistor is cut off:\n  \\[\n  I_X=0.\n  \\]\n- For \\(V_X\\ge V_T\\), the device is in saturation (not triode), with\n  \\[\n  I_X=\\frac12 \\mu_n C_{ox}\\frac{W}{L}\\,(V_X-V_T)^2.\n  \\]\n  Including channel-length modulation:\n  \\[\n  I_X=\\frac12 \\mu_n C_{ox}\\frac{W}{L}\\,(V_X-V_T)^2(1+\\lambda V_X).\n  \\]\n\nSo the \\(I_X\\)-\\(V_X\\) characteristic is zero up to threshold, then a parabolic rise with zero slope at \\(V_X=V_T\\):\n\n\\[\n\\boxed{\nI_X=\n\\begin{cases}\n0, & V_X<V_T,\\\\[2mm]\n\\dfrac12 k_n (V_X-V_T)^2, & V_X\\ge V_T,\n\\end{cases}\n\\quad k_n=\\mu_n C_{ox}\\frac{W}{L}.\n}\n\\]\n\nSketch:\n\n```text\n I_X\n  ^\n  |                           ●\n  |                       ●\n  |                  ●\n  |             ●\n  |       ___●\n  |______/________________________> V_X\n         V_T\n```\n\nThe current is positive in the direction of the drawn arrow for \\(V_X>V_T\\). For negative \\(V_X\\), it is essentially zero except for leakage/parasitic junction conduction. If the symbol in your version is the p-channel device, the same curve is mirrored: it conducts for \\(V_X<-|V_{TP}|\\), with \\(I_X\\) negative in the drawn arrow direction.",
        "format": "markdown",
        "sha256": "313279186a79b3e2db16c852ad3ed074fff472afb41e3bb48890cda8104b4506"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, its cutoff below threshold, and its saturation square-law rise above threshold. The added channel-length modulation and negative-voltage comments do not undermine the answer.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 28176,
        "total_tokens": 28816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27782,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 28176,
        "total_tokens": 28816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27782,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an enhancement n-channel MOSFET and that the drawn \\(I_X\\) arrow is positive from the \\(V_X\\) source into the drain node. The gate and drain are tied together, while the source is grounded, so\n\n\\[\nV_{GS}=V_{DS}=V_X,\\qquad V_{SB}=0.\n\\]\n\nLet the threshold voltage be \\(V_T>0\\).\n\n- For \\(V_X<V_T\\): the MOSFET is cut off (ideal MOSFET), so\n  \\[\n  I_X\\simeq 0.\n  \\]\n  In a real device there is only a small subthreshold/leakage current.\n\n- For \\(V_X>V_T\\): the device turns on and is always in saturation because\n  \\[\n  V_{DS}=V_X \\ge V_X-V_T=V_{GS}-V_T.\n  \\]\n  Hence, using the square-law model,\n  \\[\n  \\boxed{I_X=\\frac12\\,\\mu_n C_{ox}\\frac{W}{L}(V_X-V_T)^2,\n  \\qquad V_X\\ge V_T.}\n  \\]\n  Including channel-length modulation,\n  \\[\n  I_X=\\frac12\\,\\mu_n C_{ox}\\frac{W}{L}(V_X-V_T)^2(1+\\lambda V_X).\n  \\]\n\nSo the sketch is zero until \\(V_T\\), then a parabola increasing upward. It has zero slope at \\(V_X=V_T\\), and its slope increases as\n\\[\n\\frac{dI_X}{dV_X}\\approx \\mu_n C_{ox}\\frac{W}{L}(V_X-V_T)\n\\]\n(plus the small channel-length-modulation slope). There is no triode/linear region because \\(V_{GS}=V_{DS}\\).\n\n\\[\n\\begin{array}{c}\nI_X\\\\\n\\uparrow\\\\\n\\qquad\\qquad\\qquad\\qquad *\\\\\n\\qquad\\qquad\\qquad *\\\\\n\\qquad\\qquad *\\\\\n\\qquad *\\\\\n\\underline{\\qquad *\\qquad\\qquad\\quad} \\rightarrow V_X\\\\\n\\qquad V_T\n\\end{array}\n\\]\n\nMore accurately, the rise is quadratic, not straight.\n\nIf the current arrow is interpreted opposite to the one shown, the sign of the whole plot is reversed. If the drain–body junction is included, for large negative \\(V_X\\) around \\(-0.6\\ldots -0.7\\,\\)V a forward-biased drain–body diode gives a large current in the opposite direction; this is usually neglected in the ideal MOSFET sketch.",
        "format": "markdown",
        "sha256": "e306d8d0521a267c8805d1bc02cf5b695cfe83986fd657bc5e1850061f17591a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, gives approximately zero current below threshold and a quadratic saturation-current rise above threshold. The added channel-length-modulation and negative-voltage discussion does not undermine the essential answer.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 11600,
        "total_tokens": 12240,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11081,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 640,
        "output_tokens": 11600,
        "total_tokens": 12240,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11081,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an n-channel enhancement MOSFET, with its body tied to the source, and neglect channel-length modulation. The \\(1\\text{ V}\\) source fixes\n\n\\[\nV_{DS}=1\\text{ V},\\qquad V_{GS}=V_X .\n\\]\n\nLet \\(V_T\\) be the threshold voltage and let  \n\\[\nK=\\mu_n C_{ox}\\frac{W}{L}.\n\\]\n\nThen\n\n\\[\nI_X=\n\\begin{cases}\n0, & V_X<V_T,\\\\[4pt]\n\\dfrac{1}{2}K(V_X-V_T)^2, & V_T\\le V_X\\le V_T+1\\text{ V},\\\\[8pt]\nK\\left[(V_X-V_T)-\\dfrac{1}{2}\\right],\n& V_X\\ge V_T+1\\text{ V}.\n\\end{cases}\n\\]\n\nSo the sketch is:\n\n- cutoff and \\(I_X=0\\) for \\(V_X<V_T\\);\n- a quadratic (saturation) rise for \\(V_T<V_X<V_T+1\\);\n- at \\(V_X=V_T+1\\), the transistor reaches the saturation–triode boundary, where\n  \\[\n  I_X=\\frac{K}{2};\n  \\]\n- beyond that, it enters the triode region and \\(I_X\\) increases linearly with \\(V_X\\), with slope \\(K\\).\n\n\\[\n\\begin{array}{c}\nI_X\\\\\n\\uparrow\\\\\n\\\\\n\\vert\\hspace{4cm}\\diagup\\\\\n\\vert\\hspace{2.8cm}\\diagup \\quad \\text{linear, slope }K\\\\\n\\vert\\hspace{1.7cm}\\diagup\\\\\n\\vert\\hspace{0.8cm}\\cdot\\;\\; \\text{quadratic } I_X=\\frac12K(V_X-V_T)^2\\\\\n\\vert\\hspace{0.2cm}\\cdot\\\\\n\\vert\\hspace{-0.1cm}\\cdot\\\\\n\\vert\\rule[0.9ex]{5.2cm}{0.4pt}\\longrightarrow V_X\\\\\n\\quad V_T\\quad\\;\\; V_T+1\n\\end{array}\n\\]\n\nAt the knee \\(V_X=V_T+1\\),\n\\[\nI_X=\\frac{K}{2}.\n\\]\n\nIf your MOSFET symbol is depletion-mode, use the same expression with \\(V_T<0\\), so current can flow even at \\(V_X=0\\). If it were p-channel, the characteristic would be mirrored: conduction begins for \\(V_X<\\,1-|V_T|\\) when the source is at \\(+1\\text{ V}\\).",
        "format": "markdown",
        "sha256": "341f5d8a2109c052bc258ee6f7728863786596bfb0f67c42e1bfcee9286af85a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly gives the quadratic saturation rise up to V_X = V_T + 1 V and the roughly linear triode-region rise beyond, with the correct knee current. The extra device-type caveats are not needed and do not affect the essential answer.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 711,
        "output_tokens": 12350,
        "total_tokens": 13061,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 711,
        "output_tokens": 12350,
        "total_tokens": 13061,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11812,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For the n-channel enhancement MOSFET shown, the \\(1\\text{ V}\\) source fixes\n\\[\nV_{DS}=1\\text{ V},\\qquad V_{GS}=V_X.\n\\]\nLet \\(V_T\\) be the threshold voltage and\n\\[\n\\beta=\\mu_n C_{ox}\\frac{W}{L}.\n\\]\nNeglecting channel-length modulation,\n\n\\[\nI_X=\n\\begin{cases}\n0, & V_X\\le V_T,\\\\[2mm]\n\\dfrac{\\beta}{2}(V_X-V_T)^2,\n& V_T<V_X\\le V_T+1,\\quad\\text{(saturation)}\\\\[3mm]\n\\beta\\left(V_X-V_T-\\dfrac12\\right),\n& V_X\\ge V_T+1.\\quad\\text{(triode/linear)}\n\\end{cases}\n\\]\n\nSo the sketch is:\n\n- zero for \\(V_X\\le V_T\\);\n- a quadratic increase for \\(V_T<V_X<V_T+1\\);\n- after \\(V_X=V_T+1\\), the device enters the triode region; the curve continues increasing linearly with slope \\(\\beta\\), not as a flat plateau.\n\nAt the knee \\(V_X=V_T+1\\),\n\\[\nI_X=\\frac{\\beta}{2}.\n\\]\n\n\\[\n\\begin{array}{c}\nI_X\\\\[1mm]\n\\begin{array}{c}\n\\qquad\\qquad\\qquad\\qquad\\quad /\\ \\leftarrow\\ \\text{triode: slope } \\beta\\\\\n\\qquad\\qquad\\qquad\\quad\\!\\!\\!\\diagup\\\\\n\\qquad\\qquad\\quad\\!\\!\\!\\diagup \\quad\\leftarrow\\ \\text{saturation: } \\frac{\\beta}{2}(V_X-V_T)^2\\\\\n\\qquad\\quad\\!\\!\\!\\diagup\\\\\n\\displaystyle \\!\\!\\_\\_\\_\\_\\!/\\!\\!\\!\\!\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_\\_ V_X\\\\\n\\qquad\\ V_T\\quad V_T+1\n\\end{array}\n\\end{array}\n\\]\n\nIf your device has a specified threshold \\(V_T\\), substitute it on the horizontal axis; for example, if \\(V_T=1\\text{ V}\\), the transition occurs at \\(V_X=2\\text{ V}\\).",
        "format": "markdown",
        "sha256": "3e44b36a4c4105b58b37c7616375968bac6e1c8ad645e5ac2206cae4e1825c11"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the saturation-to-triode transition at VX = VT + 1 V and gives the corresponding quadratic and roughly linear current expressions and sketch.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 711,
        "output_tokens": 17715,
        "total_tokens": 18426,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17266,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 711,
        "output_tokens": 17715,
        "total_tokens": 18426,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17266,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an n-channel MOSFET. Let its threshold be \\(V_T\\) and \\(k_n=\\mu_n C_{ox}W/L\\). The source is grounded, so the drain–source voltage is fixed at \\(V_{DS}=1\\text{ V}\\), and the gate–source voltage is \\(V_{GS}=V_X\\).\n\nThe current direction shown is positive for drain-to-source current, so\n\n\\[\nI_X=\n\\begin{cases}\n0, & V_X<V_T,\\\\[4pt]\n\\dfrac{1}{2}k_n (V_X-V_T)^2, & V_T \\le V_X \\le V_T+1,\\\\[8pt]\nk_n\\left[(V_X-V_T)(1)-\\dfrac{1}{2}(1)^2\\right], & V_X>V_T+1,\n\\end{cases}\n\\]\n\nor, for the last region,\n\n\\[\nI_X=k_n\\left(V_X-V_T-\\frac12\\right).\n\\]\n\nAt \\(V_X=V_T+1\\), the current is \\(I_X=\\tfrac12 k_n\\), and the curve changes from square-law to linear with the same slope \\(k_n\\).\n\nQualitative sketch:\n\n\\[\n\\begin{array}{c}\nI_X\\\\\n\\uparrow\\\\\n\\phantom{I_X} \\quad\\quad\\quad\\quad\\quad\\quad / \\quad \\text{linear: }I_X=k_n(V_X-V_T-\\tfrac12)\\\\\n\\phantom{I_X} \\quad\\quad\\quad\\quad\\quad /\\\\\n\\phantom{I_X} \\quad\\quad\\quad\\quad /\\\\\n\\phantom{I_X} \\quad\\quad\\quad \\bullet\\ \\leftarrow V_X=V_T+1,\\ I_X=\\tfrac12 k_n\\\\\n\\phantom{I_X} \\quad\\quad / \\quad \\text{quadratic: }\\tfrac12 k_n(V_X-V_T)^2\\\\\n\\phantom{I_X} \\quad /\\\\\n0\\ \\ \\underline{\\phantom{XXXXXXXXX}}\\\\\n\\qquad V_T\\quad V_T+1 \\qquad\\longrightarrow V_X\n\\end{array}\n\\]\n\nFor \\(V_X<V_T\\), the MOSFET is off and \\(I_X=0\\). For \\(V_X>V_T+1\\), the MOSFET is in the triode region; the current continues increasing linearly with \\(V_X\\). If channel-length modulation is included, multiply the saturation-region expression by \\(1+\\lambda V_{DS}=1+\\lambda\\), but the qualitative shape is unchanged.",
        "format": "markdown",
        "sha256": "692753de478a8aed08cb13db78d1816dc9e91c9db7ee73b0d60f3b4a778d3a83"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the off, saturation, and triode regions and gives the quadratic rise up to V_T+1 V followed by a roughly linear rise. The transition current and matching slopes are also correct.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 236,
        "output_tokens": 17964,
        "total_tokens": 18200,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17468,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 236,
        "output_tokens": 17964,
        "total_tokens": 18200,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17468,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes—**provided \\(M_1\\) is a depletion-mode n-channel MOSFET and is kept in saturation.**\n\nWith gate and source both grounded, \\(V_{GS}=0\\). A depletion-mode device is already ON at zero gate-source voltage, so its drain current in saturation is approximately constant:\n\n\\[\nI_X \\approx I_{DSS}\n=\\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}|V_{th}|^2\n\\]\n\nThus the device can act as a **constant-current source/sink** (more precisely, a current sink as drawn when the source is grounded). It is not ideal: the current changes slightly with drain-source voltage due to channel-length modulation, and saturation requires sufficient \\(V_{DS}\\).\n\nIf the device were enhancement-mode, then \\(V_{GS}=0\\) would turn it off, so it could **not** act as a current source.",
        "format": "markdown",
        "sha256": "c07aa6b144434d695bf630e073628d4df757ca59c9ae51afc4dc517999a64ce7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the figure: M1 is a PMOS with gate and drain grounded, not a depletion-mode NMOS with gate and source grounded. As drawn it is diode-connected, presents low impedance, and cannot act as a current source.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 13611,
        "total_tokens": 13916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13425,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 13611,
        "total_tokens": 13916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13425,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes—for the depletion-mode n-channel device drawn (continuous channel, normally on). With the gate tied to the source,  \n\\[\nV_{GS}=0,\n\\]\nso the device is not off. If it is kept in saturation by making \\(V_{DS}\\) sufficiently large,\n\\[\nV_{DS} > -V_T \\qquad (V_T<0 \\text{ for a depletion n-MOSFET}),\n\\]\nits drain current is approximately\n\\[\nI_D \\approx \\frac12 k_n'\\,\\frac{W}{L}V_T^2 \\;=\\; I_{DSS},\n\\]\nnearly independent of \\(V_{DS}\\). Including channel-length modulation,\n\\[\nI_D \\approx I_{DSS}(1+\\lambda V_{DS}),\n\\]\nso it has a finite output resistance rather than infinite resistance.\n\nThus it can act as a **practical constant-current source**, or more precisely, in this connection it **sinks** a nearly constant current from the drain node to ground. It is not ideal: it works as a current source only while \\(V_{DS}\\) is in the saturation range (not too small, and below breakdown), and the current can vary slightly with \\(V_{DS}\\).\n\nIf \\(M_1\\) were an enhancement-mode NMOS instead, then \\(V_{GS}=0\\) would keep it off, and it could not act as a current source without additional gate bias.",
        "format": "markdown",
        "sha256": "44f949204d2cbe42fbb680c0a68f39e97f3e546c336659a31d66f7c536da213a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads M1 as a depletion NMOS with its gate tied to its source. The figure shows a diode-connected PMOS, which presents low impedance (about 1/gm) and cannot act as a current source; the candidate’s conclusion that it can is explicitly incorrect.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 18832,
        "total_tokens": 19137,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18534,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 18832,
        "total_tokens": 19137,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18534,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes—**provided \\(M_1\\) is the depletion-mode n-channel MOSFET that the symbol indicates and it remains in saturation**.\n\nWith gate and source both grounded, \\(V_{GS}=0\\). A depletion-mode NMOS is normally on, so it carries approximately a fixed drain current  \n\\[\nI_D \\approx I_{DSS}\n\\]\nwhen\n\\[\nV_{DS}\\ge V_{DS(\\rm sat)}= -V_{\\rm th}\\quad (V_{\\rm th}<0).\n\\]\nIn this region \\(I_D\\) is almost independent of \\(V_{DS}\\), so it can act as a practical constant-current source/sink. More exactly, channel-length modulation gives\n\\[\nI_D\\approx I_{DSS}(1+\\lambda V_{DS}),\n\\]\nso it is a nonideal current source with finite output resistance.\n\nIt will not act as a current source if \\(V_{DS}\\) is too small (triode region) or if the polarity is wrong. If the symbol were meant to represent an **enhancement-mode** NMOS, then \\(V_{GS}=0\\) would leave it off, and it could not act as a current source.",
        "format": "markdown",
        "sha256": "50c638c45248f40d5715499cb094f3e8263b379f35af579654db6e3d5f9a988e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads M1 as a depletion-mode NMOS and concludes it can act as a current source. As drawn, M1 is a diode-connected PMOS with low small-signal impedance, so it cannot act as a current source.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 20575,
        "total_tokens": 20880,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20328,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 305,
        "output_tokens": 20575,
        "total_tokens": 20880,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20328,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is a **p-channel enhancement MOSFET** (arrow on the source; the top terminal is the source, the bottom terminal is the drain). The circuit is a **pMOS common-source amplifier with source degeneration** through \\(R_S\\) and a drain load \\(R_D\\). The output is taken at the drain, so the stage is **inverting**.\n\n### 1. DC bias / operating point\nLet \\(I_D>0\\) be the magnitude of the dc current flowing from source to drain, i.e. downward in the figure. Then\n\\[\nV_S=V_{DD}-I_D R_S,\\qquad\nV_D=V_{\\text{out}}=I_D R_D,\\qquad\nV_G=V_{\\text{in,dc}} .\n\\]\nThus\n\\[\nV_{SG}=V_S-V_G\n      =V_{DD}-I_D R_S-V_{\\text{in,dc}},\n\\]\n\\[\nV_{SD}=V_S-V_D\n      =V_{DD}-I_D(R_S+R_D).\n\\]\n\nFor saturation of the pMOS,\n\\[\nV_{SG}>|V_{TP}|,\n\\qquad\nV_{SD}>V_{SG}-|V_{TP}|.\n\\]\nThe saturation current is\n\\[\n\\boxed{\nI_D=\\frac12\\mu_p C_{ox}\\frac{W}{L}\n\\bigl(V_{SG}-|V_{TP}|\\bigr)^2\n\\bigl(1+\\lambda V_{SD}\\bigr)\n}\n\\]\nor, neglecting channel-length modulation \\((\\lambda\\simeq0)\\),\n\\[\n\\boxed{\nI_D=\\frac12\\mu_p C_{ox}\\frac{W}{L}\n\\left(V_{DD}-I_D R_S-V_{\\text{in,dc}}-|V_{TP}|\\right)^2\n}.\n\\]\nSolve this quadratic/implicit equation for \\(I_D\\), then obtain\n\\[\n\\boxed{V_{\\text{out}}=I_D R_D,\\qquad\nV_S=V_{DD}-I_D R_S.}\n\\]\n\nIf \\(V_{SG}<|V_{TP}|\\), the pMOS is cut off: \\(I_D\\simeq0\\), \\(V_{\\text{out}}\\simeq0\\).\nIf \\(V_{SD}<V_{SG}-|V_{TP}|\\), the device is in the triode region and\n\\[\nI_D=\\mu_p C_{ox}\\frac{W}{L}\n\\left[(V_{SG}-|V_{TP}|)V_{SD}-\\frac{V_{SD}^2}{2}\\right].\n\\]\n\n### 2. Small-signal quantities\nAt the dc operating point,\n\\[\n\\boxed{\ng_m=\\mu_p C_{ox}\\frac{W}{L}\\bigl(V_{SG}-|V_{TP}|\\bigr)\n\\simeq \\sqrt{2\\mu_p C_{ox}\\frac{W}{L}I_D}\n}\n\\]\nand, if channel-length modulation is included,\n\\[\n\\boxed{r_o\\simeq\\frac{1}{\\lambda I_D}.}\n\\]\nIf the body is not tied to the source, include \\(g_{mb}=\\eta g_m\\); if the body is tied to the source, take \\(g_{mb}=0\\).\n\nThe low-frequency voltage gain is\n\\[\n\\boxed{\nA_v=\\frac{v_{\\text{out}}}{v_{\\text{in}}}\n=\n-\\frac{g_m R_D}\n{1+(g_m+g_{mb})R_S+\\dfrac{R_D+R_S}{r_o}}\n}\n\\]\nor, for \\(g_{mb}=0\\),\n\\[\n\\boxed{\nA_v=\n-\\frac{g_m R_D}\n{1+g_m R_S+\\dfrac{R_D+R_S}{r_o}}\n}\n\\]\nand, if \\(r_o\\gg R_D,R_S\\),\n\\[\n\\boxed{\nA_v\\simeq\n-\\frac{g_mR_D}{1+g_mR_S}\n=\n-\\frac{R_D}{R_S+1/g_m}.\n}\n\\]\nThe negative sign means a \\(180^\\circ\\) phase inversion.\n\nInput resistance:\n\\[\n\\boxed{R_{\\text{in}}\\to\\infty}\n\\]\nat low frequencies for an ideal MOSFET gate.\n\nOutput resistance at the output node, including \\(R_D\\),\n\\[\n\\boxed{\nR_{\\text{out}}\n=\nR_D\\parallel\n\\left[\nr_o\\!\\left(1+(g_m+g_{mb})R_S\\right)+R_S\n\\right].\n}\n\\]\nFor \\(g_{mb}=0\\),\n\\[\n\\boxed{\nR_{\\text{out}}\n=\nR_D\\parallel\n\\left[\nr_o(1+g_mR_S)+R_S\n\\right].\n}\n\\]\nIf \\(r_o\\to\\infty\\), then \\(R_{\\text{out}}\\approx R_D\\).\n\n### Summary\n- The stage is a **pMOS common-source amplifier with source degeneration**.\n- It is an **inverting amplifier**: \\(V_{\\text{in}}\\) increasing turns the pMOS more off, lowering \\(V_{\\text{out}}\\).\n- Midband gain magnitude is approximately\n  \\[\n  |A_v|\\approx \\frac{g_mR_D}{1+g_mR_S},\n  \\]\n  reduced by the source degeneration resistor \\(R_S\\).\n- If a load \\(R_L\\) is connected, replace \\(R_D\\) by \\(R_D\\parallel R_L\\) in the small-signal gain and output-resistance expressions.",
        "format": "markdown",
        "sha256": "0d3a276ee919810d0aeb8512136365607fd064aa409185e4e788758197a8bb0e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the inverting gain \u001b[?]",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 21448,
        "total_tokens": 22182,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21443,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 21448,
        "total_tokens": 22182,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21443,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the symbol is a **p-channel enhancement MOSFET** (source at the top, drain at the output), the circuit is a **PMOS common-source amplifier with source degeneration and a resistive drain load**. The input drives the gate and the output is taken at the drain, so the stage is **inverting**.\n\n### 1. DC operating point\n\nLet  \n\\[\nV_t=|V_{TP}|>0,\\qquad \\beta_p=\\mu_p C_{ox}\\frac{W}{L},\n\\]\nand let \\(I_D\\) be the PMOS current flowing from source to drain.\n\nThe terminal voltages are\n\\[\nV_S=V_{DD}-I_D R_S ,\n\\qquad\nV_{OUT}=V_D=I_D R_D .\n\\]\nThus\n\\[\nV_{SG}=V_S-V_{IN}=V_{DD}-I_D R_S-V_{IN},\n\\]\n\\[\nV_{SD}=V_S-V_D\n     =V_{DD}-I_D(R_S+R_D).\n\\]\n\nFor operation in **saturation** (normal amplifier region),\n\\[\nV_{SG}\\ge V_t,\n\\qquad\nV_{SD}\\ge V_{SG}-V_t,\n\\]\nand\n\\[\nI_D=\\frac{1}{2}\\beta_p (V_{SG}-V_t)^2(1+\\lambda V_{SD}).\n\\]\nSubstituting the node equations gives the bias equation\n\\[\nI_D=\\frac{1}{2}\\beta_p\n\\left(V_{DD}-I_D R_S-V_{IN}-V_t\\right)^2\n(1+\\lambda V_{SD}),\n\\]\nwhich is solved together with\n\\[\nV_{OUT}=I_D R_D .\n\\]\nFor \\(\\lambda\\approx0\\), set the last factor to 1.\n\nSaturation condition in output-voltage form:\n\\[\nV_{OUT}\\le V_{IN}+V_t.\n\\]\n\n- If \\(V_{SG}<V_t\\), the PMOS is **cut off**:\n  \\[\n  I_D\\approx0,\\qquad V_{OUT}\\approx0,\\qquad V_S\\approx V_{DD}.\n  \\]\n- If \\(V_{SG}\\ge V_t\\) but \\(V_{SD}<V_{SG}-V_t\\), the device is in the **triode/linear region**:\n  \\[\n  I_D=\\beta_p\\left[(V_{SG}-V_t)V_{SD}\n  -\\frac{V_{SD}^2}{2}\\right](1+\\lambda V_{SD}).\n  \\]\n\n### 2. Small-signal behavior\n\nAt the operating point,\n\\[\ng_m=\\left.\\frac{\\partial I_D}{\\partial V_{SG}}\\right|_Q\n\\simeq \\beta_p(V_{SG}-V_t)\n\\quad(\\text{or }g_m\\simeq\\sqrt{2\\beta_p I_D}\\text{ if }\\lambda=0),\n\\]\n\\[\nr_o\\simeq\\frac{1}{\\lambda I_D}.\n\\]\n\nBecause \\(R_S\\) is connected to \\(V_{DD}\\), which is an ac ground, it behaves as a **source-degeneration resistor**. Using a small-signal model,\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n=\n-\\frac{g_m R_D}\n{1+g_m R_S+\\frac{R_S+R_D}{r_o}}.\n\\]\nNeglecting channel-length modulation, \\(r_o\\to\\infty\\),\n\\[\nA_v\\simeq-\\frac{g_m R_D}{1+g_m R_S}.\n\\]\nFor strong degeneration, \\(g_mR_S\\gg1\\),\n\\[\nA_v\\simeq-\\frac{R_D}{R_S}.\n\\]\nThe negative sign shows the output is \\(180^\\circ\\) out of phase with the input.\n\nInput resistance at low frequency is essentially infinite:\n\\[\nR_{in}\\approx\\infty\n\\]\n(gate oxide), apart from gate capacitances at high frequency.\n\nThe resistance seen at the output node is\n\\[\nR_{out}\\approx R_D\\parallel\\left[r_o+R_S+g_m r_oR_S\\right].\n\\]\nIf the body effect is significant, replace \\(g_m\\) in the feedback term by \\(g_m+g_{mb}\\).\n\nIf an external ac load \\(R_L\\) is connected at \\(V_{out}\\), use\n\\[\nR_D\\parallel R_L\n\\]\nin place of \\(R_D\\) in the small-signal gain expression.\n\n### 3. Qualitative operation\n\n- Increasing \\(V_{IN}\\) raises the gate potential relative to the source, reducing \\(V_{SG}\\) and therefore reducing PMOS current. Hence \\(V_{OUT}=I_DR_D\\) falls.\n- Decreasing \\(V_{IN}\\) turns the PMOS on harder, increasing current and raising \\(V_{OUT}\\).\n- \\(R_D\\) converts the drain current into an output voltage.\n- \\(R_S\\) provides negative feedback/source degeneration: it stabilizes the bias, linearizes the transfer characteristic, reduces the small-signal gain, and increases the output resistance.\n- For use as a linear amplifier, the transistor must be biased in saturation with enough voltage swing to remain there.\n\nIn short, the circuit is an **inverting PMOS common-source amplifier with source degeneration**; its mid-band voltage gain is approximately\n\\[\n\\boxed{A_v\\approx-\\frac{g_m R_D}{1+g_m R_S}\n\\simeq-\\frac{R_D}{R_S}\\ \\text{ for large }g_mR_S.}\n\\]",
        "format": "markdown",
        "sha256": "76c757f0c718475501ce2e421e33f585ad2d4b2a6791977c1d1ed7a6e33af9cc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies a PMOS common-source stage with source degeneration and gives the inverting gain −gmRD/(1 + gmRS). The added ro and body-effect refinements are consistent with the essential analysis.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 25833,
        "total_tokens": 26567,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24700,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 25833,
        "total_tokens": 26567,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24700,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume the symbol is a **p-channel enhancement MOSFET** (the upper terminal is the source; this matches the labels \\(R_S\\) at the source and \\(R_D\\) at the drain). The circuit is a **common-source voltage amplifier with source degeneration**:  \n- input at the gate, \\(V_{\\rm in}\\)\n- output at the drain, \\(V_{\\rm out}\\)\n- \\(R_S\\) is the source-degeneration resistor\n- \\(R_D\\) is the drain load resistor\n\nWith no numerical values, only the symbolic/dc and small-signal behavior can be given.\n\n## 1. dc operating point\n\nLet \\(I_D>0\\) be the dc current from the source to the drain through \\(M_1\\), i.e. from \\(V_{DD}\\) through \\(R_S\\), the transistor, \\(R_D\\), and ground. Use \\(V_{TP}<0\\) and \\(|V_T|\\) for its magnitude.\n\n\\[\nV_S=V_{DD}-I_D R_S\n\\]\n\\[\nV_D=V_{\\rm out,Q}=I_D R_D\n\\]\n\\[\nV_{SG}=V_S-V_G\n      =V_{DD}-I_D R_S-V_G\n\\]\n\\[\nV_{SD}=V_S-V_D\n      =V_{DD}-I_D(R_S+R_D)\n\\]\n\nwhere \\(V_G\\) is the dc bias of \\(V_{\\rm in}\\).\n\nFor the PMOS to be on,\n\n\\[\nV_{SG}>|V_T|\n\\]\n\nand for saturation,\n\n\\[\nV_{SD}\\ge V_{SG}-|V_T|\n\\]\n\nor, equivalently,\n\n\\[\nV_D \\le V_G+|V_T|.\n\\]\n\nThe saturation current may be written as\n\n\\[\nI_D=\\frac12 K_p\\left(V_{SG}-|V_T|\\right)^2\n\\left(1+\\lambda V_{SD}\\right),\n\\qquad\nK_p=\\mu_p C_{ox}\\frac{W}{L},\n\\]\n\nwhere \\(\\lambda\\) is the channel-length-modulation parameter. For a simple hand analysis set \\(\\lambda=0\\). This equation is implicit because \\(V_{SG}\\) and \\(V_{SD}\\) both depend on \\(I_D\\); it must be solved together with the gate bias. If the device is in the triode region, use the corresponding linear-region equation.\n\nThus, the amplifier requires a suitable input dc bias; otherwise the operating point is not defined by the drawing.\n\n## 2. Small-signal behavior\n\nFor small signals, replace the dc supply \\(V_{DD}\\) by ac ground. The transistor is represented by a transconductance \\(g_m\\), output resistance \\(r_o\\), and, if body effect is included, \\(g_{mb}\\).\n\nFor a small-signal input \\(v_{\\rm in}\\), the voltage gain is approximately\n\n\\[\n\\boxed{\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\simeq\n-\\frac{g_m R_D}\n{1+g_m R_S+g_o(R_D+R_S)}\n}\n\\]\n\nwith \\(g_o=1/r_o\\). If the body effect is significant, replace \\(g_m\\) in the denominator by \\(g_m+g_{mb}\\):\n\n\\[\n\\boxed{\nA_v\\simeq\n-\\frac{g_m R_D}\n{1+(g_m+g_{mb})R_S+g_o(R_D+R_S)}\n}\n\\]\n\nwhere \\(g_{mb}\\) is the body-effect transconductance. If a load \\(R_L\\) is connected at the output, replace \\(R_D\\) by \\(R_D\\parallel R_L\\) in the gain formula.\n\nThe negative sign indicates that the output is **inverted** with respect to the input (180° phase shift).\n\nUseful simplifications:\n\n- If \\(r_o\\to\\infty\\) and body effect is neglected,\n\n\\[\nA_v\\simeq -\\frac{g_m R_D}{1+g_m R_S}.\n\\]\n\n- If \\(g_mR_S\\gg1\\),\n\n\\[\nA_v\\simeq -\\frac{R_D}{R_S}.\n\\]\n\nSo the gain is reduced by \\(R_S\\), but becomes more stable and linear; \\(R_S\\) provides negative current feedback.\n\nThe input resistance is approximately\n\n\\[\nR_{\\rm in}\\approx \\infty\n\\]\n\nat low frequency, since an MOS gate draws no dc current. At high frequency, the gate capacitance dominates.\n\nThe output resistance seen at the output node is\n\n\\[\nR_{\\rm out}\n=\nR_D\\parallel\n\\left[\nr_o\\left(1+(g_m+g_{mb})R_S\\right)+R_S\n\\right].\n\\]\n\nIf body effect is neglected, drop \\(g_{mb}\\). If \\(r_o\\to\\infty\\), this reduces to approximately \\(R_{\\rm out}\\approx R_D\\).\n\n## 3. Qualitative operation\n\n- If \\(V_{\\rm in}\\) is increased, \\(V_{SG}\\) decreases, so the PMOS current decreases. Hence the voltage across \\(R_D\\) decreases, so \\(V_{\\rm out}\\) decreases. This confirms the inverting behavior.\n- If \\(V_{\\rm in}\\) is high, near \\(V_{DD}\\), the PMOS turns off; \\(V_{\\rm out}\\) falls toward \\(0\\) through \\(R_D\\).\n- If \\(V_{\\rm in}\\) is low, the PMOS turns on more strongly and the output rises.\n- \\(R_S\\) degenerates the transistor and prevents the current from changing too abruptly with input voltage.\n- The stage is an **inverting common-source amplifier** with source degeneration; the output dc level is set by the bias current and \\(R_D\\).\n\nIf the symbol is actually intended to be an n-channel MOSFET, the source/drain roles and the polarity of the gain expression reverse; the output would then be taken at the source (a source-follower/common-drain configuration). The labels and terminal orientation shown, however, correspond to the p-channel interpretation above.",
        "format": "markdown",
        "sha256": "1ce7b26c367c9c1fd66fe9b6b90f0ab5cae9efd17135927d9be9b0a673ac51e8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the inverting gain −gm RD/(1 + gm RS). The additional body-effect and output-resistance refinements are consistent with the topology.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 34512,
        "total_tokens": 35246,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33296,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 734,
        "output_tokens": 34512,
        "total_tokens": 35246,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33296,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming \\(M_1\\) is an n-channel enhancement MOSFET and the circuit is analyzed at low frequency, the circuit is a **common-drain amplifier**, or **source follower**.\n\n### 1. Configuration\n- Gate: input \\(V_{\\rm in}\\)\n- Drain: connected to \\(V_{DD}\\), which is AC ground\n- Source: output \\(V_{\\rm out}\\)\n- \\(R_S\\): source resistor to ground; it sets the dc bias current and also loads the source at ac\n- No gate current flows in the MOSFET\n\nThe output is not inverted; it approximately follows the input, shifted down by one gate–source voltage:\n\\[\nV_{\\rm out}=V_{\\rm in}-V_{GS}.\n\\]\n\n### 2. DC / large-signal operation\nLet\n\\[\nI_D=\\frac{V_{\\rm out}}{R_S},\\qquad\nV_{GS}=V_{\\rm in}-V_{\\rm out}.\n\\]\nIn saturation, with\n\\[\nK=\\mu_n C_{ox}\\frac{W}{L},\\qquad\nI_D=\\frac{K}{2}(V_{GS}-V_{TH})^2,\n\\]\nwe get\n\\[\n\\frac{V_{\\rm out}}{R_S}\n=\n\\frac{K}{2}\n\\left(V_{\\rm in}-V_{\\rm out}-V_{TH}\\right)^2.\n\\]\nEquivalently, if \\(V_{OV}=V_{GS}-V_{TH}\\),\n\\[\nV_{\\rm in}=V_{TH}+V_{OV}+I_D R_S,\n\\qquad\nI_D=\\frac{K}{2}V_{OV}^2.\n\\]\nSolving for \\(V_{\\rm out}\\):\n\\[\nV_{OV}\n=\n\\frac{-1+\\sqrt{1+2K R_S(V_{\\rm in}-V_{TH})}}{K R_S},\n\\]\n\\[\nV_{\\rm out}\n=\nV_{\\rm in}-V_{TH}-V_{OV}.\n\\]\n\nThe transistor is:\n- **cut off** when \\(V_{\\rm in}\\le V_{TH}\\), giving \\(V_{\\rm out}\\approx0\\);\n- **in saturation, acting as a source follower**, when\n  \\[\n  V_{DD}\\ge V_{\\rm in}-V_{TH};\n  \\]\n  normally this is satisfied for \\(V_{\\rm in}\\le V_{DD}\\);\n- **in triode** if \\(V_{DD}<V_{\\rm in}-V_{TH}\\), where the triode current equation must be used instead.\n\nChannel-length modulation may be included by multiplying the saturation current by \\((1+\\lambda V_{DS})\\), with \\(V_{DS}=V_{DD}-V_{\\rm out}\\).\n\n### 3. Small-signal behavior\nLet\n\\[\ng_m=\\frac{\\partial I_D}{\\partial V_{GS}}\n=K V_{OV}\n=\\sqrt{2K I_D},\n\\qquad\nr_o\\approx\\frac{1}{\\lambda I_D}.\n\\]\nFor negligible body effect,\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{g_m}{g_m+\\frac{1}{R_S}+\\frac{1}{r_o}}\n=\n\\frac{g_m(R_S\\parallel r_o)}\n     {1+g_m(R_S\\parallel r_o)}.\n\\]\nThus\n\\[\n0<A_v<1,\n\\]\nand \\(A_v\\simeq 1\\) when \\(g_mR_S\\gg1\\) and \\(r_o\\) is large. The stage is non-inverting and is used as a voltage buffer.\n\nIf \\(r_o\\to\\infty\\),\n\\[\nA_v=\\frac{g_mR_S}{1+g_mR_S}.\n\\]\n\nThe low-frequency input resistance is essentially infinite:\n\\[\nR_{\\rm in}\\approx\\infty.\n\\]\n\nThe output resistance is\n\\[\nR_{\\rm out}\n=\n\\frac{1}{g_m}\n\\parallel r_o\n\\parallel R_S.\n\\]\nWith \\(r_o\\to\\infty\\),\n\\[\nR_{\\rm out}\\approx \\frac{1}{g_m}\\parallel R_S,\n\\]\nwhich is low for strong bias, giving the source follower good driving capability.\n\nIf the body is tied to ground rather than to the source, include the body-effect transconductance \\(g_{mb}=\\eta g_m\\):\n\\[\nA_v=\n\\frac{g_m}\n{g_m+g_{mb}+\\frac{1}{R_S}+\\frac{1}{r_o}},\n\\]\n\\[\nR_{\\rm out}\n=\n\\frac{1}{g_m+g_{mb}}\n\\parallel r_o\n\\parallel R_S.\n\\]\nThe body effect also raises \\(V_{TH}\\) when \\(V_{SB}=V_{\\rm out}>0\\), which must be included in the dc bias if the substrate is grounded.\n\nIf an external load \\(R_L\\) is connected from \\(V_{\\rm out}\\) to ground, replace \\(R_S\\) in the small-signal formulas by \\(R_S\\parallel R_L\\).\n\n### Summary\n- Topology: **NMOS source follower / common-drain stage**\n- Voltage gain: positive, slightly less than 1\n- Input resistance: very high\n- Output resistance: low, approximately \\(1/g_m\\parallel R_S\\)\n- Function: **voltage buffer/impedance transformer**; \\(R_S\\) sets the bias current and affects gain and output resistance\n- Bias condition for proper operation:\n  \\[\n  V_{\\rm in}>V_{TH},\n  \\qquad\n  V_{DD}\\ge V_{\\rm in}-V_{TH},\n  \\]\n  with \\(V_{\\rm out}=I_DR_S\\) and \\(V_{GS}=V_{\\rm in}-V_{\\rm out}\\).",
        "format": "markdown",
        "sha256": "49a6cbb53edc7955d36c52f2806b9628457b875fe0c5c327dc201d49b310587b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain as \\(g_mR_S/(1+g_mR_S)\\). The additional small-signal and output-resistance analysis is consistent with the circuit.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 18739,
        "total_tokens": 19368,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 18739,
        "total_tokens": 19368,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17555,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming \\(M_1\\) is an enhancement-mode n-channel MOSFET biased in saturation, the circuit is a **source follower**, also called a **common-drain amplifier**. The drain is at \\(V_{DD}\\) (ac ground), the gate is driven by \\(V_{\\rm in}\\), and the source is the output. \\(R_S\\) is the source load/bias resistor.\n\n### 1. DC/large-signal operation\nFor the MOSFET,\n\\[\nV_{GS}=V_{\\rm in}-V_{\\rm out},\\qquad\nV_{DS}=V_{DD}-V_{\\rm out}\n\\]\nand the current through \\(R_S\\) is\n\\[\nI_D=\\frac{V_{\\rm out}}{R_S}.\n\\]\n\nIf \\(V_{\\rm in}<V_T\\), \\(M_1\\) is off:\n\\[\nI_D\\simeq0,\\qquad V_{\\rm out}=0.\n\\]\n\nWhen \\(M_1\\) is on and in saturation,\n\\[\nI_D=\\frac12 k_n(V_{GS}-V_T)^2(1+\\lambda V_{DS}),\n\\]\nwith \\(k_n=\\mu_n C_{ox}W/L\\), so\n\\[\n\\frac12 k_n(V_{\\rm in}-V_{\\rm out}-V_T)^2\n\\bigl[1+\\lambda(V_{DD}-V_{\\rm out})\\bigr]\n=\\frac{V_{\\rm out}}{R_S}.\n\\]\nNeglecting channel-length modulation, this is a quadratic for \\(V_{\\rm out}\\). Its low-voltage solution is approximately\n\\[\nV_{\\rm out}\\approx V_{\\rm in}-V_T\n\\]\nbut slightly lower by the gate overdrive needed to supply the load current. For large \\(R_S\\), \\(V_{\\rm out}\\) follows \\(V_{\\rm in}\\) shifted down by approximately \\(V_{GS}\\).\n\nSaturation requires\n\\[\nV_{GS}>V_T,\\qquad V_{DS}>V_{GS}-V_T.\n\\]\nFor typical operation with \\(V_{\\rm in}\\le V_{DD}\\), this is normally satisfied once the device is on. If \\(V_{\\rm in}>V_{DD}+V_T\\), the transistor enters the triode region and the output tends toward \\(V_{DD}\\).\n\nFor a desired dc current \\(I_D\\), ignoring body effect and \\(\\lambda\\),\n\\[\nV_{\\rm out,Q}=I_DR_S,\\qquad\nV_{\\rm in,Q}=V_T+\\sqrt{\\frac{2I_D}{k_n}}+I_DR_S.\n\\]\n\n### 2. Small-signal model\nAt the operating point,\n\\[\ng_m=k_n(V_{GS,Q}-V_T)\n=\\sqrt{2k_nI_D},\n\\qquad\nr_o\\approx \\frac{1}{\\lambda I_D}.\n\\]\nIf the body effect is included, add \\(g_{mb}\\) to \\(g_m\\).\n\nWith \\(v_{gs}=v_{\\rm in}-v_{\\rm out}\\), KCL at the source gives\n\\[\ng_m(v_{\\rm in}-v_{\\rm out})\n-g_{mb}v_{\\rm out}\n-\\frac{v_{\\rm out}}{r_o}\n=\\frac{v_{\\rm out}}{R_S},\n\\]\nso\n\\[\n\\boxed{\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{g_m}\n{g_m+g_{mb}+\\frac1{r_o}+\\frac1{R_S}}\n}\n\\]\nor equivalently,\n\\[\nA_v=\n\\frac{g_m(R_S\\parallel r_o)}\n{1+(g_m+g_{mb})(R_S\\parallel r_o)}.\n\\]\n\nNeglecting body effect and \\(r_o\\),\n\\[\n\\boxed{\nA_v\\approx \\frac{g_mR_S}{1+g_mR_S}<1\n}\n\\]\nand for \\(g_mR_S\\gg1\\),\n\\[\nA_v\\approx1.\n\\]\nThus the output is **in phase** with the input and is slightly smaller than the input; the circuit behaves as a voltage buffer.\n\n### 3. Input and output resistance\nAt low frequency the gate draws essentially no current:\n\\[\n\\boxed{R_{\\rm in}\\approx\\infty}\n\\]\n(limited only by the external gate-bias network and oxide leakage).\n\nThe output resistance, including \\(R_S\\), is\n\\[\n\\boxed{\nR_{\\rm out}\n=\nR_S\\parallel\n\\left[\n\\frac{1}{g_m+g_{mb}}\\parallel r_o\n\\right]\n}\n\\]\nand, neglecting body effect and finite \\(r_o\\),\n\\[\n\\boxed{R_{\\rm out}\\approx R_S\\parallel \\frac1{g_m}\\approx \\frac1{g_m}}\n\\]\nwhen \\(R_S\\gg1/g_m\\). Hence it has a low output resistance compared with a common-source amplifier.\n\nIf an external load \\(R_L\\) is connected at \\(V_{\\rm out}\\), replace \\(R_S\\) by \\(R_S\\parallel R_L\\) in the small-signal gain expressions.\n\n### Summary\n- **Circuit type:** NMOS source follower / common-drain amplifier.\n- **Voltage gain:** \\(A_v\\lesssim 1\\), non-inverting; approximately unity for \\(g_mR_S\\gg1\\).\n- **Input resistance:** very high.\n- **Output resistance:** low, approximately \\(1/g_m\\) if \\(R_S\\) is large.\n- **Function:** voltage buffer/impedance transformer and level shifter; output follows input minus the gate-source bias voltage.\n- **Limitations:** output swing is limited by \\(V_T\\) drop and supply; \\(R_S\\) consumes dc bias current, and the circuit cannot pull all the way to \\(V_{DD}\\) unless the gate can be driven above \\(V_{DD}\\) by more than \\(V_T\\).",
        "format": "markdown",
        "sha256": "5a94c86e1a8a6fec60bbe1b0136d6a9292d2ed7cafa0f491bdba999a90eee4ab"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, including the required approximation. The body-effect, finite-r_o, and output-resistance refinements are also consistent.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 18709,
        "total_tokens": 19338,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15139,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 18709,
        "total_tokens": 19338,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15139,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming \\(M_1\\) is an n-channel MOSFET and the body is tied to the source, the circuit is a **common-drain amplifier**, also called a **source follower**. The drain is connected directly to \\(V_{DD}\\), so it is at ac ground; the input drives the gate and the output is taken at the source. The resistor \\(R_S\\) provides a dc path to ground and negative feedback.\n\n### DC / large-signal behavior\nIgnoring gate current:\n\\[\nI_D=\\frac{V_{\\rm out}}{R_S},\\qquad\nV_{GS}=V_{\\rm in}-V_{\\rm out},\\qquad\nV_{DS}=V_{DD}-V_{\\rm out}.\n\\]\n\n- If \\(V_{\\rm in}<V_{TH}\\), the MOSFET is off (for an enhancement nMOS), and\n  \\[\n  V_{\\rm out}\\approx 0.\n  \\]\n- When on and in saturation:\n  \\[\n  I_D=\\frac12\\,\\mu_n C_{ox}\\frac{W}{L}\n  \\left(V_{\\rm in}-V_{\\rm out}-V_{TH}\\right)^2,\n  \\]\n  and since \\(I_D=V_{\\rm out}/R_S\\),\n  \\[\n  \\boxed{\n  \\frac{V_{\\rm out}}{R_S}\n  =\n  \\frac12\\,\\mu_n C_{ox}\\frac{W}{L}\n  \\left(V_{\\rm in}-V_{\\rm out}-V_{TH}\\right)^2\n  }\n  \\]\n  valid while\n  \\[\n  V_{GS}>V_{TH},\\qquad\n  V_{DS}\\ge V_{GS}-V_{TH}.\n  \\]\n  Equivalently, with \\(K=\\mu_n C_{ox}W/L\\),\n  \\[\n  V_{\\rm out}\n  =\n  \\frac{1+K R_S(V_{\\rm in}-V_{TH})\n  -\\sqrt{1+2K R_S(V_{\\rm in}-V_{TH})}}\n  {K R_S}.\n  \\]\n\nThe output roughly follows the input with a dc level shift:\n\\[\nV_{\\rm out}\\approx V_{\\rm in}-V_{GS}\n= V_{\\rm in}-V_{TH}-\\sqrt{\\frac{2I_D}{K}}.\n\\]\nThe output cannot exceed the supply; with normal gate drive it has less than rail-to-rail output headroom.\n\n### Small-signal behavior\nLet the quiescent drain current be \\(I_{DQ}\\). Then\n\\[\ng_m=\\sqrt{2\\mu_n C_{ox}\\frac{W}{L}I_{DQ}},\n\\qquad\nr_o\\approx \\frac{1}{\\lambda I_{DQ}}.\n\\]\n\nAt low frequency, ignoring body effect,\n\\[\n\\boxed{\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{g_m}{g_m+\\frac{1}{R_S}+\\frac{1}{r_o}}\n}\n\\]\nor, if \\(r_o\\to\\infty\\),\n\\[\n\\boxed{\nA_v\\approx \\frac{g_mR_S}{1+g_mR_S}<1\n}\n\\]\nand is positive (non-inverting). Thus the stage has a voltage gain slightly less than unity; it approaches \\(+1\\) for large \\(g_mR_S\\).\n\nOutput resistance:\n\\[\n\\boxed{\nR_{\\rm out}\n=\n\\frac{1}{g_m+\\frac{1}{R_S}+\\frac{1}{r_o}}\n=\n\\frac{1}{g_m}\\parallel R_S\\parallel r_o\n}\n\\]\nso it is low, which is why the circuit is useful as a voltage buffer.\n\nInput resistance at low frequency is essentially infinite:\n\\[\nR_{\\rm in}\\approx \\infty\n\\]\napart from gate leakage and capacitance.\n\nIf the body is not tied to the source, include the body-effect transconductance \\(g_{mb}\\):\n\\[\nA_v=\n\\frac{g_m}{g_m+g_{mb}+\\frac{1}{R_S}+\\frac{1}{r_o}},\n\\qquad\nR_{\\rm out}\n=\n\\frac{1}{g_m+g_{mb}+\\frac{1}{R_S}+\\frac{1}{r_o}}.\n\\]\n\n### Summary\nThe circuit is an nMOS **source follower/common-drain buffer**:\n- high input impedance,\n- low output impedance,\n- voltage gain slightly below unity,\n- non-inverting,\n- output level shifted down by \\(V_{GS}\\),\n- mainly used for buffering, impedance transformation, and level shifting.\n\nA numerical bias point, gain, and swing require the values of \\(V_{DD}\\), \\(V_{\\rm in}\\), \\(V_{TH}\\), \\(\\mu_nC_{ox}W/L\\), \\(R_S\\), and \\(\\lambda\\).",
        "format": "markdown",
        "sha256": "a9a9fe88eb35a2f498b0cb479c07dead1f53e63f0340719cec58cc4a02cd2bda"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, including the required ideal expression. The additional output-resistance and body-effect discussion is consistent.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 19385,
        "total_tokens": 20014,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 19385,
        "total_tokens": 20014,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18395,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an n-channel enhancement MOSFET, with its source at the lower terminal and the body tied to the source unless otherwise stated. The gate is held at \\(V_{DD}\\), so for small signals the gate is an ac ground while the input drives the source. The output is taken at the drain. Thus the stage is a **common-gate (source-driven) amplifier**; dc-wise the transistor pulls \\(V_{out}\\) low when on and \\(R_D\\) pulls it high when off.\n\nTerminal voltages:\n\\[\nV_G=V_{DD},\\qquad V_S=V_{in},\\qquad V_D=V_{out}\n\\]\n\\[\nV_{GS}=V_{DD}-V_{in},\\qquad V_{DS}=V_{out}-V_{in}\n\\]\n\\[\nI_D=\\frac{V_{DD}-V_{out}}{R_D}\n\\]\nwhere current flows from \\(V_{DD}\\) through \\(R_D\\), through \\(M_1\\), into the \\(V_{in}\\) source.\n\n### DC / large-signal operation\nLet \\(V_{th}\\) be the threshold and \\(K_n=\\mu_n C_{ox}W/L\\).\n\n- **Cutoff:**\n\\[\nV_{in}\\ge V_{DD}-V_{th}\n\\]\nThen\n\\[\nI_D\\simeq0,\\qquad V_{out}\\simeq V_{DD}.\n\\]\n\n- **Saturation**:\n\\[\nV_{in}<V_{DD}-V_{th},\\qquad\nV_{out}\\ge V_{DD}-V_{th}\n\\]\n(ignoring body effect; otherwise replace \\(V_{th}\\) by \\(V_{th}(V_{in})\\)).\nThen\n\\[\nI_D=\\frac12 K_n\\big(V_{DD}-V_{th}-V_{in}\\big)^2\n\\]\nand\n\\[\nV_{out}\n=V_{DD}-\\frac12 K_nR_D\\big(V_{DD}-V_{th}-V_{in}\\big)^2 .\n\\]\n\n- **Triode/linear region:** when \\(V_{out}<V_{DD}-V_{th}\\) and the device is on,\n\\[\nI_D=K_n\\left[\n(V_{DD}-V_{th}-V_{in})(V_{out}-V_{in})\n-\\frac12(V_{out}-V_{in})^2\n\\right],\n\\]\nwith \\(V_{out}=V_{DD}-I_DR_D\\) solved self-consistently. In this region \\(M_1\\) behaves like a controlled switch/resistance; for large \\(R_D\\), \\(V_{out}\\approx V_{in}\\).\n\nThe saturation/triode boundary occurs at\n\\[\nV_{out}=V_{DD}-V_{th},\\qquad\nI_D=\\frac{V_{th}}{R_D}\n\\]\nand, neglecting body effect,\n\\[\nV_{in,tr}=V_{DD}-V_{th}\n-\\sqrt{\\frac{2V_{th}}{K_nR_D}}.\n\\]\nBelow this input the transistor is in triode; above it, up to cutoff, it is in saturation.\n\n### Small-signal model\nAt a saturation bias point, define\n\\[\nV_{OV}=V_{GS}-V_{th}=V_{DD}-V_{in}-V_{th}\n\\]\n\\[\ng_m=K_nV_{OV}=\\sqrt{2K_nI_D}\n=\\frac{2I_D}{V_{OV}},\n\\qquad\nr_o\\approx\\frac{1}{\\lambda I_D}.\n\\]\nIf the body is grounded rather than tied to the source, include \\(g_{mb}\\):\n\\[\ng_m'=g_m+g_{mb}.\n\\]\nIf the body is tied to the source, set \\(g_{mb}=0\\).\n\nBecause \\(v_{gs}=-v_{in}\\), the output is **in phase** with the input. For an ideal input voltage source at the source node,\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n=\n\\frac{g_m'+1/r_o}{1/R_D+1/r_o}\n=\n\\frac{R_D\\left(1+g_m'r_o\\right)}\n{R_D+r_o}.\n\\]\nWith \\(r_o\\to\\infty\\),\n\\[\nA_v\\approx g_m'R_D\n\\]\n(or simply \\(g_mR_D\\) if body effect is neglected).\n\nThe input resistance seen at the source is\n\\[\nR_{in}\n=\n\\frac{R_D+r_o}{1+g_m'r_o}\n\\approx \\frac{1}{g_m'}\n\\]\nfor \\(g_m'r_o\\gg1\\) and \\(R_D\\ll r_o\\). Thus the stage has a low input resistance.\n\nThe output resistance looking into the complete output node, with the input source set to zero, is\n\\[\nR_{out}=R_D\\parallel r_o.\n\\]\nIf the driving source at \\(V_{in}\\) has a nonzero source resistance \\(R_s\\),\n\\[\nR_{out}=R_D\\parallel\n\\left[r_o+\\left(1+g_m'r_o\\right)R_s\\right].\n\\]\nThe voltage gain from an ideal generator \\(v_s\\) behind \\(R_s\\) is reduced by the input divider:\n\\[\n\\frac{v_{out}}{v_s}\n=A_v\\frac{R_{in}}{R_s+R_{in}}.\n\\]\n\n### Summary of behavior\n- In saturation it is a **non-inverting common-gate amplifier** with gain about \\(g_mR_D\\) and low input resistance.\n- As a digital/level-restorer circuit:\n  - \\(V_{in}\\) low turns \\(M_1\\) strongly on, so \\(V_{out}\\) is pulled low; ideally \\(V_{out}\\approx V_{in}\\) when \\(R_D\\) is large.\n  - \\(V_{in}\\approx V_{DD}\\) turns \\(M_1\\) off, so \\(R_D\\) pulls \\(V_{out}\\) high to \\(V_{DD}\\).\n- For linear amplification, it must be biased in saturation, i.e. the drain/output must remain near \\(V_{DD}\\), and the input source must be able to sink/source the transistor current.\n\nThe expressions above neglect capacitive effects and assume channel-length modulation only through \\(r_o\\); for a body not tied to the source, replace \\(V_{th}\\) by the body-bias-dependent threshold and add \\(g_{mb}\\) to \\(g_m\\) in the small-signal results.",
        "format": "markdown",
        "sha256": "dcc9b7868c63a3126dadceaa04848e77a4f354fa709a2ac9f092aff15de54334"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven common-gate topology and gives the non-inverting gain and low source input resistance, including appropriate output-resistance effects. The additional large-signal and body-effect discussion does not undermine the essential analysis.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 608,
        "output_tokens": 32426,
        "total_tokens": 33034,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31098,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 608,
        "output_tokens": 32426,
        "total_tokens": 33034,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31098,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming \\(M_1\\) is an n-channel enhancement MOSFET and \\(V_{DD}\\) is an ideal dc supply:\n\n## Configuration\n- Gate: tied to \\(V_{DD}\\), so it is at dc bias and is an ac ground.\n- Source: driven by \\(V_{\\rm in}\\).\n- Drain: connected to \\(R_D\\) and taken out as \\(V_{\\rm out}\\).\n\nThus, for small signals this is a **common-gate MOSFET stage**: the input is applied to the source, the output is taken from the drain, and the gate is ac-grounded. The stage is **non-inverting**: increasing \\(V_{\\rm in}\\) decreases \\(V_{GS}\\), decreases \\(I_D\\), and therefore raises \\(V_{\\rm out}\\).\n\n## DC operation\n\\[\nV_{GS}=V_{DD}-V_{\\rm in}\n\\]\nThe MOSFET conducts only when\n\\[\nV_{DD}-V_{\\rm in}>V_{th}\n\\quad\\Leftrightarrow\\quad\nV_{\\rm in}<V_{DD}-V_{th}.\n\\]\nIf this condition is not satisfied, the transistor is cut off:\n\\[\nI_D\\simeq0,\\qquad V_{\\rm out}=V_{DD}.\n\\]\n\nDrain-node KCL gives\n\\[\nV_{\\rm out}=V_{DD}-I_D R_D.\n\\]\n\nIf \\(M_1\\) is in saturation, ignoring channel-length modulation,\n\\[\nI_D=\\frac12 K_n\\left(V_{DD}-V_{\\rm in}-V_{th}\\right)^2,\n\\]\nwhere \\(K_n=\\mu_n C_{ox}(W/L)\\). Therefore\n\\[\nV_{\\rm out}\n=\nV_{DD}\n-\\frac12 K_nR_D\n\\left(V_{DD}-V_{\\rm in}-V_{th}\\right)^2.\n\\]\nThe saturation condition is\n\\[\nV_{DS}\\ge V_{GS}-V_{th}\n\\;\\Rightarrow\\;\nV_{\\rm out}-V_{\\rm in}\\ge V_{DD}-V_{\\rm in}-V_{th},\n\\]\nso\n\\[\nV_{\\rm out}\\ge V_{DD}-V_{th}.\n\\]\nEquivalently, ignoring channel-length modulation, \\(I_D R_D\\le V_{th}\\). If this is not satisfied, the device enters the triode region, where\n\\[\nI_D=K_n\\left[(V_{DD}-V_{\\rm in}-V_{th})(V_{\\rm out}-V_{\\rm in})\n-\\frac12(V_{\\rm out}-V_{\\rm in})^2\\right],\n\\]\nand \\(V_{\\rm out}=V_{DD}-I_DR_D\\) must be solved simultaneously.\n\n## Small-signal model\nAt a saturation-region bias point,\n\\[\ng_m=K_n(V_{DD}-V_{\\rm in}-V_{th})\n=\\sqrt{2K_nI_D},\n\\qquad\nr_o=\\frac{1}{\\lambda I_D}.\n\\]\nIf the body/substrate is not tied to the source, include the body-effect transconductance \\(g_{mb}=\\eta g_m\\). For a discrete three-terminal MOSFET where body and source are tied, \\(g_{mb}=0\\).\n\nThe low-frequency voltage gain is approximately\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx\n(g_m+g_{mb})(R_D\\parallel r_o),\n\\]\nand is positive. If \\(r_o\\) is large,\n\\[\nA_v\\approx g_mR_D.\n\\]\nA more exact expression, neglecting \\(g_{mb}\\), is\n\\[\nA_v=\n\\frac{g_m+1/r_o}{1/R_D+1/r_o}\n=\n\\left(g_m+\\frac1{r_o}\\right)(R_D\\parallel r_o).\n\\]\n\nThe input resistance looking into the source is low:\n\\[\nR_{\\rm in}\\approx \\frac{1}{g_m+g_{mb}},\n\\]\nor more exactly, including \\(r_o\\) and \\(R_D\\),\n\\[\nR_{\\rm in}=\n\\frac{R_D+r_o}{1+(g_m+g_{mb})r_o}.\n\\]\nThe output resistance is\n\\[\nR_{\\rm out}\\approx R_D\\parallel r_o.\n\\]\n\n## Summary\nThe circuit is an NMOS **common-gate amplifier** with a resistive drain load, biased by connecting the gate to \\(V_{DD}\\). It has:\n- non-inverting voltage gain,\n- low input resistance, high output resistance,\n- gain \\(\\sim g_m(R_D\\parallel r_o)\\),\n- useful linear operation only while \\(M_1\\) remains in saturation.\n\nBecause the gate is tied directly to \\(V_{DD}\\), the permissible output swing in saturation is limited by \\(V_{\\rm out}\\ge V_{DD}-V_{th}\\). Numerical currents, voltages, and gain cannot be found without values for \\(V_{DD}\\), \\(V_{th}\\), \\(K_n\\), \\(R_D\\), and the dc level of \\(V_{\\rm in}\\).",
        "format": "markdown",
        "sha256": "1370cf25827f83c729105d3edfc8924e4a6992f300a9a7512c23b473c7ca9ab0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven, ac-grounded-gate common-gate stage and its positive gain. The gain and low input-resistance expressions, including the finite-r_o refinement, are consistent with the golden solution; the additional bias analysis does not undermine the essential answer.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 512,
        "input_tokens": 608,
        "output_tokens": 19699,
        "total_tokens": 20307,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18664,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 512,
        "input_tokens": 608,
        "output_tokens": 19699,
        "total_tokens": 20307,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18664,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming \\(M_1\\) is an enhancement-mode **NMOS** with its gate (the right-hand terminal) tied to \\(V_{DD}\\), its source driven by \\(V_{\\rm in}\\), and its drain connected to \\(V_{\\rm out}\\) through \\(R_D\\), the circuit is a **resistor-loaded common-gate amplifier**. Its small-signal output is **in phase** with the input at the source; it is not an inverter.\n\nLet\n\\[\nK_n=\\mu_n C_{ox}\\frac{W}{L},\\qquad V_T=\\text{threshold voltage}.\n\\]\nFor a dc bias point \\(V_{IN}\\), set\n\\[\nV_G=V_{DD},\\quad V_S=V_{IN},\\quad V_D=V_{OUT},\n\\]\nso\n\\[\nV_{GS}=V_{DD}-V_{IN},\\qquad\nV_{DS}=V_{OUT}-V_{IN}.\n\\]\nThe resistor current is\n\\[\nI_D=\\frac{V_{DD}-V_{OUT}}{R_D}.\n\\]\n\n### 1. Large-signal / dc behavior\nThe transistor is on when\n\\[\nV_{IN}<V_{DD}-V_T.\n\\]\n\n**Saturation** (neglecting channel-length modulation):\n\\[\nI_D=\\frac{K_n}{2}\\bigl(V_{DD}-V_T-V_{IN}\\bigr)^2,\n\\]\n\\[\nV_{OUT}=V_{DD}-\\frac{K_n R_D}{2}\n\\bigl(V_{DD}-V_T-V_{IN}\\bigr)^2.\n\\]\nSaturation requires\n\\[\nV_{DS}\\ge V_{GS}-V_T\n\\quad\\Longrightarrow\\quad\nV_{OUT}\\ge V_{DD}-V_T.\n\\]\nThus, because the gate is tied to \\(V_{DD}\\), a saturation-biased amplifier has its output close to \\(V_{DD}\\). If this inequality fails, \\(M_1\\) is in the triode region.\n\n**Triode**:\n\\[\nI_D=K_n\\!\\left[\n(V_{DD}-V_T-V_{IN})(V_{OUT}-V_{IN})\n-\\frac{(V_{OUT}-V_{IN})^2}{2}\n\\right],\n\\]\nwith \\(V_{OUT}=V_{DD}-I_D R_D\\).\n\n**Cutoff**:\n\\[\nV_{IN}\\ge V_{DD}-V_T\n\\quad\\Rightarrow\\quad\nI_D\\approx0,\\qquad V_{OUT}=V_{DD}.\n\\]\n\nIncluding channel-length modulation, multiply the saturation current by\n\\[\n1+\\lambda(V_{OUT}-V_{IN}),\n\\]\nand solve the resulting equations simultaneously.\n\n### 2. Small-signal model\nAt the quiescent point,\n\\[\ng_m\\approx K_n(V_{GS,Q}-V_T)\\approx \\frac{2I_{D,Q}}{V_{GS,Q}-V_T},\n\\]\n\\[\nr_o\\approx \\frac{1}{\\lambda I_{D,Q}}\n\\quad(\\lambda=0\\Rightarrow r_o\\to\\infty).\n\\]\nIf the body is not connected to the source, include the body-effect transconductance \\(g_{mb}=\\eta g_m\\); then replace \\(g_m\\) by \\(g_m+g_{mb}\\) in the common-gate formulas below.\n\nThe small-signal voltage gain is\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\left(g_m+\\frac{1}{r_o}\\right)(R_D\\parallel r_o)\n\\;\\approx\\; g_m R_D\n\\qquad\\text{(positive/non-inverting)}.\n\\]\nWith a load \\(R_L\\), replace \\(R_D\\) by \\(R_D\\parallel R_L\\).\n\nThe input resistance looking into the source is\n\\[\nR_{\\rm in}=\\frac{r_o+R_D}{1+g_m r_o}\n\\;\\approx\\;\\frac{1}{g_m}.\n\\]\nThe output resistance, for an ideal input voltage source, is\n\\[\nR_{\\rm out}=R_D\\parallel r_o\\approx R_D.\n\\]\nIf the input source has a source resistance \\(R_s\\), the gain is reduced by the divider\n\\[\n\\frac{v_{\\rm in}}{v_s}=\\frac{R_{\\rm in}}{R_s+R_{\\rm in}},\n\\]\nand\n\\[\nR_{\\rm out}\n=\nR_D\\parallel\\!\\left[r_o+(1+g_m r_o)R_s\\right].\n\\]\n\n### 3. Interpretation\n- The stage is a **common-gate amplifier** or a non-inverting resistor-loaded NMOS stage.\n- Increasing \\(V_{\\rm in}\\) reduces \\(V_{GS}\\), reduces the drain current, and therefore raises \\(V_{\\rm out}\\): hence the positive gain.\n- Its input resistance is low (\\(\\sim 1/g_m\\)), so it loads a voltage source significantly.\n- Tying the gate directly to \\(V_{DD}\\) gives limited saturation headroom; for a normal mid-rail amplifier, the gate should instead be dc-biased at a suitable fixed voltage and ac-grounded.\n- With large input swings, the transistor moves through triode, saturation, and cutoff, so the transfer characteristic is nonlinear; the formulas above are valid piecewise.\n\nIf the device is a PMOS rather than an NMOS, the same topology holds but the voltage polarities and inequalities are reversed; the gain magnitude is essentially the same.",
        "format": "markdown",
        "sha256": "93b1d5c516f3718114c3d8cb8d94a65a53232d3ad73969cda42f71794b8a4288"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven, gate-AC-grounded NMOS as a common-gate stage, with non-inverting gain and source input resistance near 1/gm. The additional bias and small-signal analysis is consistent with the topology.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 608,
        "output_tokens": 32081,
        "total_tokens": 32689,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30970,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 608,
        "output_tokens": 32081,
        "total_tokens": 32689,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30970,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit uses an \\(n\\)-channel enhancement MOSFET \\(M_1\\) with gate biased at \\(V_b\\), drain connected through \\(R_D\\) to \\(V_{DD}\\), and output taken at the drain. The input is coupled through \\(C_1\\).\n\n### 1. DC bias\nFor dc, \\(C_1\\) is open. From the drawing, the source is tied directly to ground, so\n\\[\nV_G=V_b,\\qquad V_S=0,\\qquad V_{GS}=V_b.\n\\]\nIf \\(V_b<V_T\\), the transistor is off:\n\\[\nI_D=0,\\qquad V_{out}=V_{DD}.\n\\]\nIf \\(V_b>V_T\\), the drain current in saturation is\n\\[\nI_D\\approx \\frac12\\mu_n C_{ox}\\frac{W}{L}(V_b-V_T)^2,\n\\]\n(including channel-length modulation, multiply by \\(1+\\lambda V_{out}\\)). Thus\n\\[\nV_{out}=V_{DD}-I_D R_D.\n\\]\nThe saturation condition is\n\\[\nV_{out} \\ge V_b-V_T.\n\\]\nIf this is not satisfied, the MOSFET operates in the triode region:\n\\[\nI_D=\\mu_n C_{ox}\\frac{W}{L}\n\\left[(V_b-V_T)V_{out}-\\frac{V_{out}^2}{2}\\right],\n\\]\nand \\(V_{out}=V_{DD}-I_DR_D\\) must be solved together with it.\n\n### 2. Small-signal behavior “as drawn”\nBecause the source is tied directly to ground and an ideal dc gate bias is an ac ground,\n\\[\nv_g=0,\\qquad v_s=0\\implies v_{gs}=0.\n\\]\nTherefore the small-signal drain current is zero:\n\\[\ni_d=g_m v_{gs}+g_{mb}v_{bs}=0.\n\\]\nHence\n\\[\nv_{out}=0,\\qquad \\boxed{A_v=\\frac{v_{out}}{v_{in}}\\approx 0.}\n\\]\nIn other words, the input through \\(C_1\\) is ac-shorted to ground; the circuit as drawn does not amplify the indicated input.\n\nThe small-signal output resistance at the drain is\n\\[\nR_{out}=R_D\\parallel r_o.\n\\]\nThe input source only drives \\(C_1\\) to ground, so the impedance seen by \\(V_{in}\\) is essentially\n\\[\nZ_{in}\\approx \\frac{1}{j\\omega C_1},\n\\]\ni.e. the source node is an ac short at midband.\n\n### 3. If the intended circuit is a common-gate amplifier\nIf the ground under the source is not intended as a direct ac short—i.e., the source is meant to be the driven input with proper dc bias/current source—the stage is a common-gate amplifier. Then, with gate ac grounded and \\(v_s=v_{in}\\),\n\\[\nv_{gs}=-v_{in}.\n\\]\nIncluding body effect,\n\\[\nG_m=g_m+g_{mb}=(1+\\eta)g_m.\n\\]\nThe voltage gain is non-inverting:\n\\[\n\\boxed{A_v=\\frac{v_{out}}{v_{in}}=G_m\\left(R_D\\parallel r_o\\right)}\n\\]\nor, if \\(R_D\\ll r_o\\) and body effect is neglected,\n\\[\n\\boxed{A_v\\approx g_mR_D.}\n\\]\nThe source input resistance is approximately\n\\[\n\\boxed{R_{in}\\approx \\frac{1}{g_m+g_{mb}}}\n\\]\nwith a more exact expression\n\\[\nR_{in}=\\frac{r_o+R_D}{1+(g_m+g_{mb})r_o}.\n\\]\nThe output resistance with an ideal input voltage source is\n\\[\n\\boxed{R_{out}=R_D\\parallel r_o.}\n\\]\nIn saturation,\n\\[\ng_m=\\sqrt{2\\mu_n C_{ox}\\frac{W}{L}I_D}\n=\\mu_n C_{ox}\\frac{W}{L}(V_{GS}-V_T).\n\\]\n\nSo, as drawn, the source is directly grounded and the input is shorted to ground, giving \\(A_v\\approx0\\). The usual intended interpretation of this topology would be a common-gate amplifier, whose gain is approximately \\(g_m(R_D\\parallel r_o)\\), non-inverting.",
        "format": "markdown",
        "sha256": "58357a082ddae85f83aa03ea9b6d4850c19e187b859f696470faad7ec5e61ad4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly notices that the source/input node is hard-shorted to ground and concludes the as-drawn circuit has ideally zero gain from Vin. The separate intended common-gate discussion does not undermine that conclusion.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 16949,
        "total_tokens": 17854,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 16949,
        "total_tokens": 17854,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an enhancement-mode \\(n\\)-channel MOSFET, \\(C_1\\) is large enough to be an ac short and an open circuit at dc, and the body effect is neglected unless stated otherwise.\n\n\\[\n\\beta=\\mu_n C_{ox}\\frac{W}{L},\\qquad V_{OV}=V_{GS}-V_{TH}\n\\]\n\n## 1. Important point about the drawing\nThe gate is held at the dc bias \\(V_b\\); the output is at the drain. The input is coupled through \\(C_1\\) to the source. This is the topology of a **common-gate amplifier**.  \n\nHowever, the drawing also shows the source connected directly to ground. If that is a true dc/ac short, then \\(C_1\\) is effectively connected between \\(V_{in}\\) and ground, so \\(V_{in}\\) cannot modulate \\(V_{GS}\\). In that literal case, \\(V_{out}\\) is independent of \\(V_{in}\\) and the circuit only establishes a dc bias. A practical common-gate stage requires a dc bias current source/resistor from source to ground, not a direct short.\n\n## 2. DC operating point (as drawn, source grounded)\nAt dc, \\(C_1\\) is open and the gate draws no current:\n\n\\[\nV_G=V_b,\\qquad V_S=0,\\qquad V_{GS}=V_b\n\\]\n\nFor cutoff, \\(V_b\\le V_{TH}\\):\n\n\\[\nI_D\\approx 0,\\qquad V_{out}=V_{DD}\n\\]\n\nIf \\(M_1\\) is in saturation and channel-length modulation is neglected:\n\n\\[\nI_D=\\frac{\\beta}{2}(V_b-V_{TH})^2\n\\]\n\n\\[\nV_{out}=V_D=V_{DD}-I_DR_D\n\\]\n\nSaturation requires approximately\n\n\\[\nV_D\\ge V_b-V_{TH}\n\\]\n\nIf this condition is not satisfied, \\(M_1\\) enters the triode region:\n\n\\[\nI_D=\\beta\\left[(V_b-V_{TH})V_D-\\frac12V_D^2\\right],\n\\qquad\nV_D=V_{DD}-I_DR_D\n\\]\n\nand must be solved together with the resistor equation. Including channel-length modulation replaces the saturation current by\n\n\\[\nI_D=\\frac{\\beta}{2}(V_b-V_{TH})^2(1+\\lambda V_D)\n\\]\n\nwith \\(r_o\\approx 1/(\\lambda I_D)\\).\n\nThe small-signal parameters are\n\n\\[\ng_m=\\sqrt{2\\beta I_D}\\approx \\frac{2I_D}{V_{OV}},\n\\qquad\nr_o\\approx \\frac{1}{\\lambda I_D}.\n\\]\n\n## 3. Small-signal gain\n### Literal connection: source grounded\nFor an ideal input source and ideal grounded source,\n\n\\[\nv_s=0,\\qquad v_{gs}=v_g-v_s=0\n\\]\n\nso the input \\(v_{in}\\) produces no change in drain current:\n\n\\[\n\\boxed{\\frac{v_{out}}{v_{in}}=0}\n\\]\n\nAs drawn, the circuit does not amplify \\(V_{in}\\); it is only a dc-biased MOSFET load.\n\nIf instead the signal is applied to the gate bias \\(V_b\\), then the circuit is an ordinary common-source amplifier:\n\n\\[\n\\boxed{A_v=\\frac{v_{out}}{v_b}\\approx -g_m(R_D\\parallel r_o)}\n\\]\n\nIt is inverting, has high input resistance, and\n\n\\[\nR_{out}\\approx R_D\\parallel r_o.\n\\]\n\n### Intended common-gate operation\nIf a proper source bias current source/resistor is present so the source is not ac-shorted, the gate is at ac ground and the input drives the source. Then, neglecting body effect,\n\n\\[\nv_{gs}=-v_s\n\\]\n\nand the voltage gain from source to drain is\n\n\\[\n\\boxed{\nA_v=\\frac{v_{out}}{v_s}\n\\approx g_m(R_D\\parallel r_o)\n}\n\\]\n\nMore exactly,\n\n\\[\nA_v=\\frac{(g_mr_o+1)R_D}{R_D+r_o}.\n\\]\n\nThe gain is positive/non-inverting. If body effect is included, replace \\(g_m\\) by \\(g_m+g_{mb}\\).\n\nInput resistance looking into the source:\n\n\\[\n\\boxed{\nR_{in}\\approx \\frac{1}{g_m}\n}\n\\]\n\nwith the more exact expression\n\n\\[\nR_{in}=\\frac{R_D+r_o}{1+g_mr_o}.\n\\]\n\nOutput resistance for an ideal input voltage source:\n\n\\[\n\\boxed{\nR_{out}\\approx R_D\\parallel r_o.\n}\n\\]\n\nIf the source is driven through a generator resistance \\(R_s\\), the overall gain is reduced by the input divider:\n\n\\[\n\\frac{v_{out}}{v_{in}}\n=\nA_v\\frac{R_{in}}{R_s+R_{in}}.\n\\]\n\n## 4. Role of \\(C_1\\)\n\\(C_1\\) provides ac coupling/DC blocking. In a proper common-gate stage its impedance must be small at signal frequencies. Its lower cutoff frequency is approximately\n\n\\[\nf_L\\approx\\frac{1}{2\\pi C_1(R_s+R_{in})}.\n\\]\n\n## Summary\n- The schematic is intended to be an **NMOS common-gate amplifier**, biased by \\(V_b\\), loaded by \\(R_D\\), with output at the drain.\n- In a proper common-gate connection:\n  - voltage gain is non-inverting and roughly \\(g_m(R_D\\parallel r_o)\\),\n  - input resistance is low, \\(\\sim 1/g_m\\),\n  - output resistance is high, \\(\\sim R_D\\parallel r_o\\),\n  - it is useful as a current buffer/wideband stage and as part of a cascode.\n- As drawn, with the source directly grounded, \\(V_{in}\\) is effectively shorted to ground; the circuit does not amplify \\(V_{in}\\). A source bias current source/resistor or a different input connection is required for actual amplification.",
        "format": "markdown",
        "sha256": "da75e3529bdf19976d441f357b682b7e2f04cf6782b67eec01e24782dcdb2a8d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It explicitly notices that the source is hard-shorted to ground and concludes that the input is shunted and the ideal gain from Vin is zero, matching the full-credit rule. The discussion of an intended common-gate stage is clearly conditional.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 896,
        "input_tokens": 905,
        "output_tokens": 26165,
        "total_tokens": 27070,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24204,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 896,
        "input_tokens": 905,
        "output_tokens": 26165,
        "total_tokens": 27070,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24204,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an \\(n\\)-channel enhancement MOSFET, the bias \\(V_b\\) is ideal at signal frequencies, and \\(C_1\\) is large enough to be an ac short in the midband. Define\n\\[\nK_n=\\mu_n C_{ox}\\frac{W}{L},\\qquad\nV_{OV}=V_{GS}-V_{TH},\n\\]\nand, when channel-length modulation is included,\n\\[\nI_D=\\frac12 K_n V_{OV}^2(1+\\lambda V_{DS}),\\qquad\nr_o\\simeq \\frac{1}{\\lambda I_D}.\n\\]\n\n## Important point about the drawing\nThe transistor is operating as a common-gate stage only if its source is allowed to move with the input. In the drawing, however, the source is connected directly to ground. At signal frequencies an ideal ground is a short, so\n\\[\nv_s=0 \\quad\\Rightarrow\\quad v_{gs}=v_g-v_s=0.\n\\]\nThus, **with the circuit exactly as drawn, the input signal is shorted to ground and the circuit does not amplify**. It behaves as a dc-biased MOSFET current sink with a drain resistor \\(R_D\\). The input sees only \\(C_1\\) to ground:\n\\[\nZ_{in}= \\frac{1}{sC_1},\\qquad\nv_{out,ac}=0,\\qquad\nR_{out}=R_D\\parallel r_o.\n\\]\nAt dc, \\(C_1\\) is open; \\(v_{in}\\) has no dc effect on the source.\n\n## DC bias for the drawn circuit\nBecause the source is grounded,\n\\[\nV_G=V_b,\\qquad V_S=0,\\qquad V_{GS}=V_b.\n\\]\n\n- If \\(V_b\\le V_{TH}\\), \\(M_1\\) is off:\n  \\[\n  I_D=0,\\qquad V_{out}=V_{DD}.\n  \\]\n- If \\(M_1\\) is in saturation:\n  \\[\n  I_D\\simeq \\frac12 K_n (V_b-V_{TH})^2,\n  \\qquad\n  V_{out}=V_{DD}-I_D R_D.\n  \\]\n  Including \\(\\lambda\\), solve\n  \\[\n  I_D=\\frac12 K_n (V_b-V_{TH})^2\n  [1+\\lambda(V_{DD}-I_DR_D)].\n  \\]\n  Saturation requires\n  \\[\n  V_b>V_{TH},\\qquad\n  V_{out}=V_{DD}-I_DR_D>V_b-V_{TH}.\n  \\]\n- If \\(V_{out}\\) falls below \\(V_b-V_{TH}\\), \\(M_1\\) enters the triode region and the triode equation must be used:\n  \\[\n  I_D=K_n\\left[(V_b-V_{TH})V_{DS}-\\frac12 V_{DS}^2\\right],\n  \\qquad\n  V_{DS}=V_{DD}-I_DR_D.\n  \\]\n\n## If the intended circuit is the usual common-gate amplifier\nMost textbooks draw this stage with a source-bias current sink or other dc return that is open to ac, rather than a direct short to ground. In that intended case, \\(C_1\\) couples the input to the source, \\(V_b\\) is an ac ground at the gate, and the drain is the output. Then, in saturation:\n\\[\ng_m=K_n V_{OV}=\\sqrt{2K_n I_D},\n\\qquad\nr_o=\\frac{1}{\\lambda I_D}.\n\\]\nIf the body is grounded separately from the source, include the body-effect transconductance \\(g_{mb}=\\eta g_m\\); if the body is tied to the source, set \\(g_{mb}=0\\).\n\nThe midband small-signal results are:\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n=\n\\left(g_m+g_{mb}+\\frac{1}{r_o}\\right)\n(R_D\\parallel r_o),\n\\]\nor, for \\(r_o\\) large and negligible body effect,\n\\[\n\\boxed{A_v\\approx g_m(R_D\\parallel r_o)\\approx g_mR_D.}\n\\]\nThe output is **non-inverting** with respect to the source input.\n\nThe input resistance looking into the source is approximately\n\\[\n\\boxed{R_{in}\\approx \\frac{1}{g_m+g_{mb}}\\approx \\frac{1}{g_m}}\n\\]\nwhen body effect is neglected. A more exact expression including \\(r_o\\) is\n\\[\nR_{in}=\\frac{R_D+r_o}{1+(g_m+g_{mb})r_o}.\n\\]\nThe output resistance, with an ideal voltage source driving the input, is approximately\n\\[\n\\boxed{R_{out}\\approx R_D\\parallel r_o.}\n\\]\nIf an ac load \\(R_L\\) is connected at the output, replace \\(R_D\\) by \\(R_D\\parallel R_L\\) in the small-signal gain and output-resistance formulas.\n\nThe coupling capacitor \\(C_1\\) produces a high-pass response with a low-frequency corner approximately\n\\[\nf_L\\simeq \\frac{1}{2\\pi C_1\\big(R_{in}+R_{\\text{source}}\\big)}\n\\]\nfor the common-gate interpretation. At high frequencies, transistor parasitic capacitances together with \\(R_D\\parallel r_o\\) introduce a low-pass roll-off.\n\nSo the key conclusion is: **as drawn, the source is ac-shorted to ground and the stage has zero small-signal gain. If the source ground is meant to represent a dc-bias/current-source return rather than an ideal ac short, then the circuit is a common-gate amplifier with \\(A_v\\approx g_m(R_D\\parallel r_o)\\), low input resistance \\(\\sim 1/g_m\\), and output resistance \\(\\sim R_D\\parallel r_o\\).**",
        "format": "markdown",
        "sha256": "64547c830747657947fe102b3c1a9838b8c2d2c6f7f6c1f29b0f05bffd948fdd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly notices that the source is directly shorted to ground and concludes that the input is shorted, giving ideally zero small-signal gain. The additional common-gate analysis is explicitly conditional on a different circuit interpretation.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 896,
        "input_tokens": 905,
        "output_tokens": 32656,
        "total_tokens": 33561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30817,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 896,
        "input_tokens": 905,
        "output_tokens": 32656,
        "total_tokens": 33561,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30817,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **two poles**.\n\nReason: In the small-signal high-frequency model, the source is grounded, so \\(C_{SB}\\) is shorted and has no effect. The independent capacitive nodes are the **gate node** and the **drain/output node**; \\(C_{GS}\\), \\(C_{GD}\\), and \\(C_{DB}\\) form a second-order network. The feedback capacitance \\(C_{GD}\\) also creates a transmission zero, but it does not add another pole.\n\n\\[\n\\boxed{2\\text{ poles (and one zero)}}\n\\]\n\nIn a dominant-pole approximation it is often treated as approximately single-pole, but the exact circuit is second-order.",
        "format": "markdown",
        "sha256": "91b5411db1368a5e9685c3823ef95403924329fba01b3c0a839f0c4d7bac23c1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the count by noting that C_SB is shorted out and the remaining capacitors provide two independent energy-storage states. The zero and dominant-pole comments are consistent.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 996,
        "output_tokens": 10603,
        "total_tokens": 11599,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10460,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 996,
        "output_tokens": 10603,
        "total_tokens": 11599,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10460,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **two poles** (and one zero due to \\(C_{GD}\\)).\n\nReason: in the small-signal model, the two independent capacitive nodes are the gate node and the output/drain node. \\(C_{SB}\\) is effectively shorted to ground because the source is grounded, so it does not add a pole. The remaining \\(C_{GS}\\), \\(C_{GD}\\), and \\(C_{DB}\\) give a second-order denominator, hence **2 finite poles**.",
        "format": "markdown",
        "sha256": "635101e1c4dbd4288e8f3923ce0930a396e5a2553682f640886d066766aabf3d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the capacitor count: CSB is shorted because the source is grounded, while the remaining capacitors yield a second-order denominator.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 996,
        "output_tokens": 7920,
        "total_tokens": 8916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7821,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 996,
        "output_tokens": 7920,
        "total_tokens": 8916,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7821,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **2 finite poles** (assuming the MOSFET source is grounded as drawn in the small-signal circuit).\n\nReason: \\(C_{SB}\\) is shorted by the source-to-ground connection, so it does not add a pole. The independent dynamic nodes are the **gate** and the **drain/output**; \\(C_{GD}\\) couples them, while \\(C_{GS}\\) and \\(C_{DB}\\) are shunt capacitances. The resulting transfer function has a second-order denominator, hence two poles.",
        "format": "markdown",
        "sha256": "7f20e8e87478ca8e136b0f49111538dc5a068d888f632e2f736bc6be6885eb85"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles and justifies the count by noting that CSB is shorted and the gate/drain capacitances provide two independent dynamic states.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 997,
        "output_tokens": 17598,
        "total_tokens": 18595,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17491,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 997,
        "output_tokens": 17598,
        "total_tokens": 18595,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17491,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume \\(M_1\\) is an n-channel enhancement MOSFET, the gate current is negligible, and the body is tied to the source unless noted. Define\n\n\\[\nk=\\frac{R_2}{R_1+R_2}\\qquad (0<k<1), \\qquad R_F=R_1+R_2 .\n\\]\n\nThe gate is biased from the drain by the \\(R_1R_2\\) divider, while the input drives the source. This is a negative-feedback amplifier; from \\(V_{\\rm in}\\) to \\(V_{\\rm out}\\) it is non-inverting.\n\n## DC / large-signal operation\n\nWith no gate current,\n\n\\[\nV_G=kV_{\\rm out},\n\\]\nso\n\\[\nV_{GS}=kV_{\\rm out}-V_{\\rm in},\\qquad\nV_{DS}=V_{\\rm out}-V_{\\rm in}.\n\\]\n\nThe drain current from the supply/load side is\n\n\\[\nI_D=\\frac{V_{DD}-V_{\\rm out}}{R_D}\n-\\frac{V_{\\rm out}}{R_1+R_2},\n\\]\n\nwhere the second term is the current through the feedback divider. If \\(R_1+R_2\\gg R_D\\), this divider loading can be neglected.\n\nIn saturation,\n\n\\[\nI_D=\\frac12 K_n(V_{GS}-V_T)^2\n\\quad\\text{(ignoring channel-length modulation)},\n\\]\n\nso\n\n\\[\n\\boxed{\n\\frac{(V_{DD}-V_{\\rm out})}{R_D}\n-\\frac{V_{\\rm out}}{R_1+R_2}\n=\n\\frac12 K_n\\!\\left(kV_{\\rm out}-V_{\\rm in}-V_T\\right)^2\n}\n\\]\n\nfor the on/saturation region. The transistor is in saturation while on (for \\(V_{\\rm out}>0\\)):\n\n\\[\nV_{DS}\\ge V_{GS}-V_T\n\\;\\Longrightarrow\\;\n(1-k)V_{\\rm out}+V_T\\ge0.\n\\]\n\nIt cuts off when\n\n\\[\nkV_{\\rm out}-V_{\\rm in}<V_T.\n\\]\n\nAt cutoff, the output is set by the \\(R_D\\)–\\((R_1+R_2)\\) divider:\n\n\\[\nV_{\\rm out}\\approx V_{DD}\\frac{R_1+R_2}{R_D+R_1+R_2},\n\\]\nor approximately \\(V_{DD}\\) if \\(R_1+R_2\\gg R_D\\).\n\nIf the loop gain is large,\n\n\\[\nV_{GS}\\approx V_T \\quad (\\text{or }V_T+V_{\\rm ov}),\n\\]\n\nso\n\n\\[\n\\boxed{\nV_{\\rm out}\\approx\n\\frac{V_{\\rm in}+V_T+V_{\\rm ov}}{k}\n=\n\\left(1+\\frac{R_1}{R_2}\\right)\n\\bigl(V_{\\rm in}+V_T+V_{\\rm ov}\\bigr),\n}\n\\]\n\nwhere \\(V_{\\rm ov}=V_{GS}-V_T\\) depends on the bias current. Thus the output is a level-shifted, amplified version of the input. Small changes are amplified by approximately\n\n\\[\n\\boxed{\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx \\frac1k\n=1+\\frac{R_1}{R_2}.\n}\n\\]\n\n## Small-signal analysis\n\nLet \\(g_m\\) be the MOSFET transconductance, \\(r_o\\) its small-signal output resistance, and \\(g_{mb}\\) the body-effect transconductance. Nodal analysis gives\n\n\\[\n\\boxed{\nA_v=\n\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{\ng_m+g_{mb}+\\frac1{r_o}\n}{\n\\frac1{R_D}+\\frac1{R_1+R_2}\n+k g_m+\\frac1{r_o}\n}\n}\n\\]\n\nwhere \\(k=R_2/(R_1+R_2)\\).  \nIf the body is tied to the source or body effect is ignored, set \\(g_{mb}=0\\).  \nIf \\(r_o\\to\\infty\\) and the feedback divider does not load the output appreciably,\n\n\\[\n\\boxed{\nA_v\\approx\n\\frac{g_mR_D}{1+k g_mR_D}.\n}\n\\]\n\nFor large loop gain \\(k g_mR_D\\gg1\\), this reduces to the familiar resistor-ratio result:\n\n\\[\n\\boxed{\nA_v\\approx \\frac1k\n=1+\\frac{R_1}{R_2}.\n}\n\\]\n\nThe loop-gain magnitude is approximately\n\n\\[\n\\boxed{\nT\\approx k g_m\\left(R_D\\parallel (R_1+R_2)\\parallel r_o\\right).\n}\n\\]\n\nLarger \\(T\\) gives a gain closer to \\(1/k\\) and lowers the output resistance.\n\n### Input resistance seen at \\(V_{\\rm in}\\)\n\nIncluding the loading of \\(R_1+R_2\\),\n\n\\[\n\\boxed{\nR_{\\rm in}\\approx\n\\frac{R_D\\parallel (R_1+R_2)}{A_v}.\n}\n\\]\n\nWith high loop gain and neglecting body effect,\n\n\\[\nR_{\\rm in}\\approx\nk\\left[R_D\\parallel (R_1+R_2)\\right].\n\\]\n\nNotice that the input is the MOSFET source, so this is not an extremely high-impedance input; the feedback raises its input resistance above that of a simple common-gate stage, but it can still load the driving source.\n\n### Output resistance\n\nWith the input source ac-grounded,\n\n\\[\n\\boxed{\nR_{\\rm out}=\n\\left[\n\\frac1{r_o}\n+\\frac1{R_D}\n+\\frac1{R_1+R_2}\n+k g_m\n\\right]^{-1}.\n}\n\\]\n\nIf \\(r_o\\) and feedback-divider loading are ignored,\n\n\\[\n\\boxed{\nR_{\\rm out}\\approx\nR_D\\parallel \\frac1{k g_m}\n=\n\\frac{R_D}{1+k g_mR_D}.\n}\n\\]\n\nThus negative feedback lowers the output resistance; in the high-gain limit the output behaves somewhat like a voltage source whose value is set by the \\(R_1/R_2\\) divider.\n\n## Summary\n\n- \\(M_1\\) is an n-channel MOSFET used as a feedback amplifier.\n- Feedback is taken from the drain and applied to the gate through \\(R_1,R_2\\); the input is applied to the source.\n- It is non-inverting from \\(V_{\\rm in}\\) to \\(V_{\\rm out}\\).\n- Closed-loop gain is approximately  \n  \\[\n  A_v\\approx 1+\\frac{R_1}{R_2}\n  \\]\n  when the loop gain is large.\n- The output has a dc offset due to \\(V_T\\) (and overdrive), and the usable linear range is limited by the supply and by cutoff/saturation of \\(M_1\\).\n- Negative feedback reduces output resistance and makes the gain depend mainly on \\(R_1/R_2\\), while bandwidth and linearity improve at the expense of reduced gain.",
        "format": "markdown",
        "sha256": "fb6e95286a82150f34dfcc5e41d97da96b07d380898de1166598c4dd033317bd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven input, output-divider feedback to the gate, and negative feedback, with the correct non-inverting closed-loop gain approaching 1/k = 1 + R1/R2. Extra analyses do not contradict the essential model.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 38344,
        "total_tokens": 39217,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33957,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 38344,
        "total_tokens": 39217,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33957,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume the device is an \\(n\\)-channel enhancement MOSFET, operating in saturation, with negligible gate current and low-frequency operation. The body is taken to be tied to the source; if it is tied to ground, include the body-effect transconductance \\(g_{mb}\\) as noted below.\n\nDefine the feedback factor\n\\[\n\\beta=\\frac{R_2}{R_1+R_2},\\qquad R_{12}=R_1+R_2 .\n\\]\n\n## 1. Circuit function\nThe MOSFET is used as a common-gate stage: the signal enters at the source, and the output is taken at the drain. The divider \\(R_1,R_2\\) feeds a fraction of the output back to the gate:\n\\[\nV_F=\\beta V_{\\rm out},\\qquad \nV_{GS}=V_F-V_{\\rm in}=\\beta V_{\\rm out}-V_{\\rm in}.\n\\]\nSince an increase in \\(V_{\\rm out}\\) raises the gate voltage, increases \\(I_D\\), and therefore drops more voltage across \\(R_D\\), the feedback opposes the change. Thus it is negative feedback.\n\nTopology: **series mixing at the input and voltage/shunt sampling at the output** (a voltage-series or series-shunt feedback amplifier). Its small-signal output is **non-inverting** with respect to the source input. For large loop gain, the gain is set mainly by the resistor ratio:\n\\[\nA_v\\approx \\frac1{\\beta}=1+\\frac{R_1}{R_2}.\n\\]\n\n## 2. DC operating point\nAt dc,\n\\[\nV_F=\\beta V_{\\rm out},\n\\]\nand the drain-node current balance is\n\\[\nI_D=\\frac{V_{DD}-V_{\\rm out}}{R_D}-\\frac{V_{\\rm out}}{R_1+R_2}.\n\\]\nEquivalently,\n\\[\nI_D=\\frac{V_{DD}\\frac{R_{12}}{R_D+R_{12}}-V_{\\rm out}}\n{R_D\\parallel R_{12}}.\n\\]\nIf the MOSFET is in saturation,\n\\[\nI_D=\\frac12\\mu_n C_{ox}\\frac{W}{L}\n\\bigl(\\beta V_{\\rm out}-V_{\\rm in}-V_T\\bigr)^2\n\\]\n(optionally multiplied by \\(1+\\lambda(V_{\\rm out}-V_{\\rm in})\\)). Substituting this into the current balance and solving the resulting quadratic gives the quiescent \\(V_{\\rm out}\\). For very large \\(g_m\\),\n\\[\n\\beta V_{\\rm out}\\approx V_{\\rm in}+V_T\n\\quad\\Rightarrow\\quad\nV_{\\rm out}\\approx \\frac{V_{\\rm in}+V_T}{\\beta}\n=\\left(1+\\frac{R_1}{R_2}\\right)(V_{\\rm in}+V_T).\n\\]\nThe transistor is on for\n\\[\n\\beta V_{\\rm out}-V_{\\rm in}>V_T.\n\\]\nIf this is not satisfied it is cut off, and\n\\[\nV_{\\rm out}=\\frac{V_{DD}(R_1+R_2)}{R_D+R_1+R_2}.\n\\]\nFor saturation,\n\\[\nV_{DS}\\ge V_{GS}-V_T,\n\\]\nwhich gives\n\\[\nV_{\\rm out}(1-\\beta)+V_T\\ge 0.\n\\]\nThis is normally satisfied for a positive output bias.\n\n## 3. Small-signal analysis\nLet\n\\[\ng_m=\\sqrt{2\\mu_n C_{ox}\\frac{W}{L}I_{DQ}}\n\\]\nand \\(r_o=1/(\\lambda I_{DQ})\\). At low frequency the gate draws no current, so\n\\[\nv_g=\\beta v_o.\n\\]\n\n### Simplified result (neglect \\(r_o\\), no external load)\nWith\n\\[\nR_p=R_D\\parallel(R_1+R_2),\n\\]\nthe small-signal voltage gain from source to drain is\n\\[\n\\boxed{\nA_v=\\frac{v_o}{v_{\\rm in}}\n=\n\\frac{g_mR_p}{1+g_m\\beta R_p}\n}\n\\]\nand the small-signal input resistance seen at the source is\n\\[\n\\boxed{\nR_{\\rm in}\n=\n\\frac{1+g_m\\beta R_p}{g_m}\n=\n\\frac1{g_m}+\\beta R_p .\n}\n\\]\nThe output resistance seen back into the output node, with the input source set to zero and no external load, is\n\\[\n\\boxed{\nR_{\\rm out}\n=\nR_p\\parallel\\frac{1}{g_m\\beta}\n=\n\\frac{R_p}{1+g_m\\beta R_p}.\n}\n\\]\nIf \\(R_1+R_2\\gg R_D\\), these reduce approximately to\n\\[\nA_v\\approx \\frac{g_mR_D}{1+g_m\\beta R_D},\n\\qquad\nR_{\\rm in}\\approx \\frac1{g_m}+\\beta R_D,\n\\qquad\nR_{\\rm out}\\approx R_D\\parallel\\frac1{g_m\\beta}.\n\\]\n\n### Including \\(r_o\\)\nWith \\(R_p=R_D\\parallel(R_1+R_2)\\) (set \\(R_p\\) also in parallel with an external load if one is connected),\n\\[\n\\boxed{\nA_v=\n\\frac{g_m+1/r_o}\n{1/R_D+1/(R_1+R_2)+1/r_o+g_m\\beta}\n}\n\\]\n\\[\n\\boxed{\nR_{\\rm in}=\n\\frac{1+\\frac{R_p}{r_o}+g_m\\beta R_p}\n{g_m+1/r_o}\n}\n\\]\n\\[\n\\boxed{\nR_{\\rm out}=\nr_o\\parallel R_D\\parallel(R_1+R_2)\\parallel\\frac1{g_m\\beta}.\n}\n\\]\nAn external load \\(R_L\\) appears in parallel at the output. For a finite source resistance \\(R_s\\), the source-node signal is attenuated as\n\\[\nv_s=v_{\\rm in}\\frac{R_{\\rm in}}{R_s+R_{\\rm in}},\n\\]\nso multiply the gain by \\(R_{\\rm in}/(R_s+R_{\\rm in})\\).\n\nIf the body is not tied to the source but grounded, add \\(g_{mb}\\) to \\(g_m\\) in the numerator of \\(A_v\\) and to the denominator of \\(R_{\\rm in}\\); for an ideal input voltage source, \\(R_{\\rm out}\\) above is unchanged.\n\n## Key conclusions\n- \\(R_D\\) converts the drain current to output voltage and sets the quiescent current together with the feedback bias.\n- \\(R_1,R_2\\) provide negative voltage feedback and set the closed-loop gain approximately to \\(1+R_1/R_2\\).\n- The feedback stabilizes the bias and gain, lowers the output resistance, and increases the input resistance compared with the same common-gate stage without feedback.\n- The output is in phase with the source input; the transistor must be biased so that it remains on and in saturation for the desired signal swing.",
        "format": "markdown",
        "sha256": "2710444046487cc814bc1cc692c03a38e5e6cba9d1ff5506154a57b59971b4bb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-to-gate divider feedback, and negative-feedback action; its closed-loop gain is also correct. Extra bias and resistance discussions are not required.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 45951,
        "total_tokens": 46824,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 44497,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 45951,
        "total_tokens": 46824,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 44497,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the transistor is an \\(n\\)-channel enhancement MOSFET operating in saturation, with negligible gate current and body effect:\n\n## 1. Circuit function\nThis is a source-driven MOSFET amplifier with negative feedback from the drain to the gate. The divider \\(R_1,R_2\\) samples \\(V_{\\text{out}}\\) and returns a fraction to the gate:\n\\[\nV_F=\\frac{R_2}{R_1+R_2}V_{\\text{out}}\n\\]\nThus\n\\[\nV_{GS}=V_F-V_{\\text{in}}\n=\\frac{R_2}{R_1+R_2}V_{\\text{out}}-V_{\\text{in}}.\n\\]\nThe feedback is negative because an increase in \\(V_{\\text{out}}\\) raises the gate voltage, which tends to increase the MOSFET current and pull \\(V_{\\text{out}}\\) back down. The output is in phase with the input at the source.\n\n## 2. DC bias equations\nLet\n\\[\n\\beta=\\frac{R_2}{R_1+R_2}.\n\\]\nFor DC values \\(V_{\\text{in}},V_{\\text{out}}\\):\n\\[\nV_{GS}=\\beta V_{\\text{out}}-V_{\\text{in}},\\qquad\nV_{DS}=V_{\\text{out}}-V_{\\text{in}}.\n\\]\nThe drain current in saturation is\n\\[\nI_D=\\frac12\\mu_nC_{ox}\\frac{W}{L}\n\\left(V_{GS}-V_{TH}\\right)^2(1+\\lambda V_{DS}).\n\\]\nKCL at the drain gives\n\\[\n\\frac{V_{DD}-V_{\\text{out}}}{R_D}=I_D.\n\\]\nSolve these equations for \\(V_{\\text{out}}\\). For \\(\\lambda\\simeq0\\), define\n\\[\nx=V_{GS}-V_{TH}>0.\n\\]\nThen\n\\[\nx=\n\\frac{-1+\\sqrt{1+2\\beta R_DK(\\beta V_{DD}-V_{\\text{in}}-V_{TH})}}\n{\\beta R_DK},\n\\]\nwhere \\(K=\\mu_nC_{ox}W/L\\), and\n\\[\nV_{\\text{out}}=\\frac{V_{\\text{in}}+V_{TH}+x}{\\beta}.\n\\]\nSaturation requires\n\\[\nV_{DS}>V_{GS}-V_{TH}.\n\\]\n\n## 3. Small-signal gain\nFor small-signal analysis, let\n\\[\nr_o\\simeq\\frac{1}{\\lambda I_D},\\qquad\ng_m=\\mu_nC_{ox}\\frac{W}{L}\\left(V_{GS}-V_{TH}\\right)\n\\simeq\\sqrt{2K I_D}.\n\\]\nAlso define\n\\[\nR_F=R_1+R_2,\\qquad\nR_\\parallel=R_D\\parallel R_F\\parallel r_o.\n\\]\nThen\n\\[\n\\boxed{\nA_v=\\frac{v_{\\text{out}}}{v_{\\text{in}}}\n=\n\\frac{(g_m+1/r_o)R_\\parallel}\n{1+g_m\\beta R_\\parallel}\n}\n\\]\nwhere \\(\\beta=R_2/(R_1+R_2)\\).\n\nFor \\(r_o\\to\\infty\\),\n\\[\n\\boxed{\nA_v\\simeq\n\\frac{g_m(R_D\\parallel (R_1+R_2))}\n{1+g_m\\beta(R_D\\parallel (R_1+R_2))}\n}\n\\]\nand if the loop gain is large,\n\\[\n\\boxed{\nA_v\\simeq \\frac{1}{\\beta}\n=1+\\frac{R_1}{R_2}.\n}\n\\]\nThus the closed-loop voltage gain is set mainly by \\(R_1/R_2\\). The polarity is non-inverting from \\(V_{\\text{in}}\\) to \\(V_{\\text{out}}\\).\n\n## 4. Input and output resistance\nLooking into the source from \\(V_{\\text{in}}\\):\n\\[\n\\boxed{\nR_{\\text{in}}\n=\n\\frac{1+R_L(g_m\\beta+1/r_o)}\n{g_m+1/r_o},\n\\qquad\nR_L=R_D\\parallel(R_1+R_2)\n}\n\\]\nFor large \\(r_o\\),\n\\[\n\\boxed{\nR_{\\text{in}}\\simeq \\frac{1}{g_m}\n+\\beta\\left[R_D\\parallel(R_1+R_2)\\right].\n}\n\\]\n\nLooking into the drain with the input source set to zero:\n\\[\n\\boxed{\nR_{\\text{out}}\n=\n\\frac{1}\n{\\frac1{R_D}+\\frac1{R_1+R_2}+\\frac1{r_o}+g_m\\beta}\n}\n\\]\nor\n\\[\n\\boxed{\nR_{\\text{out}}\n=\n\\frac{R_D\\parallel(R_1+R_2)\\parallel r_o}\n{1+g_m\\beta\\left[R_D\\parallel(R_1+R_2)\\parallel r_o\\right]}.\n}\n\\]\nFor large loop gain,\n\\[\nR_{\\text{out}}\\approx \\frac{1}{g_m\\beta},\n\\]\nso negative feedback lowers the output resistance.\n\n## Summary\n- The circuit is a negative-feedback MOSFET voltage amplifier with series voltage mixing and output-voltage sampling.\n- Its closed-loop gain is approximately\n\\[\n\\boxed{A_v\\approx 1+\\frac{R_1}{R_2}}\n\\]\nwhen \\(g_m\\beta R_\\parallel\\gg1\\).\n- Negative feedback stabilizes the gain, increases the input resistance, and reduces the output resistance.\n- The MOSFET must remain in saturation; otherwise replace the square-law saturation current by the triode-region equation.",
        "format": "markdown",
        "sha256": "b2b0ce410f187f37886d2c9e1482223b43d56d8c6b0144906d6f236f5a959a14"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven input, output-divider feedback to the gate, and negative feedback, and gives the correct gain in the large-loop-gain limit. The finite-\u001b[0mro and resistance details are secondary and do not undermine the essential answer.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 22897,
        "total_tokens": 23770,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21729,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 873,
        "output_tokens": 22897,
        "total_tokens": 23770,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21729,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Taking the transistor symbols as NMOS devices, the circuit is an **NMOS source follower (common-drain amplifier) with an active current-source load**.\n\n### 1. Circuit function\n- \\(M_1\\): NMOS source follower.  \n  - Gate: \\(V_{\\rm in}\\)\n  - Drain: \\(V_{DD}\\)\n  - Source: \\(V_{\\rm out}\\)\n- \\(M_2\\): NMOS biased by \\(V_b\\), acting as a current sink/current-source load.  \n  - It fixes the quiescent current \\(I_Q\\) through \\(M_1\\).\n\nThus the output is taken at the source of \\(M_1\\), so the circuit is a voltage buffer/level shifter: \\(V_{\\rm out}\\) follows \\(V_{\\rm in}\\) with a dc offset.\n\n### 2. DC operation\nAssume both devices are in saturation. With\n\\[\n\\beta_i=\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_i,\n\\]\nthe first-order currents are\n\\[\nI_Q \\approx \\frac{\\beta_2}{2}(V_b-V_{T2})^2\n\\]\nfor \\(M_2\\), and\n\\[\nI_Q \\approx \\frac{\\beta_1}{2}\\left(V_{\\rm in}-V_{\\rm out}-V_{T1}\\right)^2\n\\]\nfor \\(M_1\\), neglecting channel-length modulation and body effect. Equating them gives\n\\[\nV_{\\rm out}\\approx V_{\\rm in}-V_{T1}-\\sqrt{\\frac{2I_Q}{\\beta_1}}\n   = V_{\\rm in}-V_{GS1}.\n\\]\nSo the output follows the input shifted down by the gate–source voltage of \\(M_1\\).\n\nIf the body of \\(M_1\\) is grounded, body effect increases \\(V_{T1}\\) as \\(V_{\\rm out}\\) rises:\n\\[\nV_{T1}=V_{T0}+\\gamma\\left(\\sqrt{2\\phi_F+V_{\\rm out}}-\\sqrt{2\\phi_F}\\right),\n\\]\nso the dc transfer is somewhat nonlinear. If the body is tied to the source, there is no body effect.\n\nBias conditions:\n\\[\nV_b>V_{T2},\n\\]\n\\[\nV_{\\rm out}>V_b-V_{T2}=V_{ov2}\n\\]\nfor \\(M_2\\) to remain in saturation, and\n\\[\nV_{\\rm in}-V_{\\rm out}>V_{T1}\n\\]\nfor \\(M_1\\) to be on. In normal operation \\(M_1\\) is saturated because its drain is at \\(V_{DD}\\).\n\nIncreasing \\(V_b\\) increases the bias current \\(I_Q\\), which increases \\(V_{GS1}\\) and therefore lowers \\(V_{\\rm out}\\) for a fixed \\(V_{\\rm in}\\).\n\n### 3. Small-signal behavior\nUsing the small-signal model, including body effect and finite output resistances,\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{g_{m1}}\n{g_{m1}+g_{mb1}+\\frac{1}{r_{o1}}+\\frac{1}{r_{o2}}}\n=\n\\frac{g_{m1}R_L}{1+(g_{m1}+g_{mb1})R_L},\n\\]\nwhere\n\\[\nR_L=r_{o1}\\parallel r_{o2}\n\\]\n(and any external load can be placed in parallel with these).\n\nUsually \\(g_m\\gg 1/r_o\\), so\n\\[\nA_v\\approx 1,\n\\]\nand it is positive (non-inverting). With body effect,\n\\[\nA_v\\approx \\frac{g_{m1}}{g_{m1}+g_{mb1}}<1.\n\\]\n\nThe output resistance is\n\\[\nR_{\\rm out}\n=\n\\frac{1}{g_{m1}+g_{mb1}+g_{ds1}+g_{ds2}}\n\\approx \\frac{1}{g_{m1}},\n\\]\nso the source follower has a low output resistance. Its low-frequency input resistance is essentially infinite because it is the gate of a MOSFET.\n\n### 4. Use and limitations\n- Acts as a voltage buffer/level shifter: high input impedance, low output resistance, voltage gain close to unity.\n- \\(V_b\\) sets the bias current and therefore the operating point.\n- Output swing is limited by the threshold/overdrive of \\(M_1\\) and by the saturation voltage of \\(M_2\\).\n- Body effect and channel-length modulation reduce the gain and cause nonlinearity.\n- Proper operation requires both transistors to remain in saturation; otherwise the buffer clips or the current-source load no longer behaves ideally.",
        "format": "markdown",
        "sha256": "67204046f0367af8ee7b607cbff1515c61a061c504fd8b8ae4fa19dc4cf6bccc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its current-source load, and gives the positive, slightly sub-unity gain with appropriate body-effect and finite-output-resistance refinements. This meets the golden solution’s full-credit rule.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 14684,
        "total_tokens": 15313,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12869,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 14684,
        "total_tokens": 15313,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12869,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "### Circuit type\nAssuming the symbols are **n-channel enhancement MOSFETs**, the circuit is an **NMOS source follower (common-drain amplifier)** with an active **current-source load**:\n\n- \\(M_1\\): input transistor; drain at \\(V_{DD}\\), gate at \\(V_{in}\\), source at \\(V_{out}\\).\n- \\(M_2\\): biased current sink; drain at \\(V_{out}\\), source at ground, gate at \\(V_b\\).\n- \\(V_{out}\\) is taken at the source of \\(M_1\\), so \\(M_1\\) acts as a voltage follower.\n\n### DC operation\nThe same current flows through both transistors:\n\\[\nI_D=I_{D1}=I_{D2}.\n\\]\nFor \\(M_2\\) in saturation, the bias current is set by \\(V_b\\):\n\\[\nI_D \\approx \\frac{1}{2}\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2\n(V_b-V_{T2})^2\n\\]\nneglecting channel-length modulation/body effect.\n\nFor \\(M_1\\) in saturation:\n\\[\nI_D \\approx \\frac{1}{2}\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_1\n(V_{in}-V_{out}-V_{T1})^2.\n\\]\nEquating the currents gives, ignoring body effect and \\(\\lambda\\):\n\\[\nV_{out}\n= V_{in}-V_{T1}\n-\\sqrt{\\frac{(W/L)_2}{(W/L)_1}}\\,(V_b-V_{T2}).\n\\]\nThus the output is a **level-shifted version of the input**, shifted down by approximately \\(V_{GS1}\\). With body effect, replace \\(V_{T1}\\) by \\(V_{T1}(V_{out})\\).\n\nFor proper linear operation:\n\\[\nV_b>V_{T2},\n\\]\n\\[\nV_{in}>V_{out}+V_{T1},\n\\]\nand \\(M_2\\) should remain in saturation:\n\\[\nV_{out}\\ge V_b-V_{T2}.\n\\]\nAlso, \\(V_{in}\\) must be kept below the value that would push \\(M_1\\) into triode—usually not a problem for \\(V_{in}\\le V_{DD}\\).\n\n### Small-signal behavior\nLet\n\\[\ng_{m1}=\\sqrt{2\\beta_1 I_D},\\qquad\nr_{o1}=\\frac{1}{\\lambda I_D},\\qquad\nr_{o2}=\\frac{1}{\\lambda I_D}.\n\\]\nIf body effect is included, let \\(g_{mb1}\\) be the body-effect transconductance; set \\(g_{mb1}=0\\) if the body of \\(M_1\\) is tied to its source.\n\nThe small-signal voltage gain is\n\\[\n\\boxed{\nA_v=\\frac{v_{out}}{v_{in}}\n=\n\\frac{g_{m1}}\n{g_{m1}+g_{mb1}+g_{o1}+g_{o2}}\n}\n\\]\nwith \\(g_{o1}=1/r_{o1}\\), \\(g_{o2}=1/r_{o2}\\).  \nIf body effect and finite output resistance are neglected:\n\\[\n\\boxed{A_v\\approx 1}\n\\]\nand it is **positive/non-inverting**.\n\nInput resistance:\n\\[\n\\boxed{R_{in}\\approx \\infty}\n\\]\nat low frequencies.\n\nOutput resistance:\n\\[\n\\boxed{\nR_{out}\n=\n\\frac{1}{g_{m1}+g_{mb1}+g_{o1}+g_{o2}}\n\\approx \\frac{1}{g_{m1}+g_{mb1}}\n\\approx \\frac{1}{g_{m1}}\n}\n\\]\nso the output impedance is low.\n\n### Summary\n- **Function:** non-inverting voltage buffer / source follower with a current-source load.\n- **Gain:** slightly less than unity, \\(A_v\\lesssim 1\\), positive.\n- **Input impedance:** very high.\n- **Output impedance:** low, approximately \\(1/g_{m1}\\).\n- **DC output:** \\(V_{out}\\approx V_{in}-V_{GS1}\\), so it provides a level shift.\n- **Bias:** \\(V_b\\) sets the current through \\(M_2\\), which fixes the quiescent current and therefore the overdrive of \\(M_1\\).\n- **Main limitation:** limited output swing/headroom; for \\(M_2\\) to behave as a good current source, it must remain in saturation.",
        "format": "markdown",
        "sha256": "365d547523c7d0a18b1cb727861b582347a034e09ff835fe54930d54d41d33e2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its NMOS current-source load, with a positive gain slightly below unity. The gain and low output-resistance expressions also match the expected small-signal behavior.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 20854,
        "total_tokens": 21483,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19886,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 20854,
        "total_tokens": 21483,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19886,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is an **NMOS source follower (common-drain stage) with an NMOS current-sink load**.  \n- \\(M_1\\): input transistor; gate is driven by \\(V_{\\rm in}\\), drain at \\(V_{DD}\\), source at the output node.\n- \\(M_2\\): active load/current sink; biased by \\(V_b\\), drain at the output node, source grounded.\n- Output is taken at the source of \\(M_1\\)/drain of \\(M_2\\).\n\nAssuming both transistors are n-channel enhancement MOSFETs and are biased in saturation (body tied to source for the simple first-order result; if the body is grounded, include body effect), let\n\\[\n\\beta_i=\\mu_n C_{ox}\\left(\\frac WL\\right)_i ,\\qquad V_T\\text{ = threshold voltage.}\n\\]\n\n### 1. DC operating point\n\nThe lower transistor sets the bias current:\n\\[\nI_Q \\simeq \\frac12\\beta_2(V_b-V_T)^2,\n\\]\nvalid when\n\\[\nV_b>V_T,\\qquad V_{\\rm out}\\ge V_b-V_T\n\\]\nso that \\(M_2\\) remains in saturation and behaves as a current source.\n\nThe same current flows through \\(M_1\\), so\n\\[\nI_Q \\simeq \\frac12\\beta_1(V_{\\rm in}-V_{\\rm out}-V_T)^2 .\n\\]\nEquating the currents gives, ignoring channel-length modulation and body effect,\n\\[\nV_{\\rm out}\n\\simeq V_{\\rm in}-V_T-\\sqrt{\\frac{2I_Q}{\\beta_1}}\n= V_{\\rm in}-V_T-\\sqrt{\\frac{\\beta_2}{\\beta_1}}\\,(V_b-V_T).\n\\]\nIf \\(M_1\\) and \\(M_2\\) are matched \\((\\beta_1=\\beta_2)\\), this simplifies to\n\\[\nV_{\\rm out}\\simeq V_{\\rm in}-V_b\n\\]\nor, more generally,\n\\[\nV_{\\rm out}=V_{\\rm in}-V_{GS1},\n\\]\nwhere \\(V_{GS1}\\) is set by the bias current. Thus the output **follows the input, shifted downward by one gate-source voltage**. It is a non-inverting level shifter/buffer.\n\nFor \\(M_1\\) saturation:\n\\[\nV_{DD}-V_{\\rm out}\\ge V_{\\rm in}-V_{\\rm out}-V_T\n\\quad\\Rightarrow\\quad\nV_{\\rm in}\\lesssim V_{DD}+V_T.\n\\]\nFor normal input swings below \\(V_{DD}\\), \\(M_1\\) stays saturated. If \\(V_{\\rm in}\\) is too low, \\(M_1\\) cuts off and the follower relation fails; \\(M_2\\) then enters triode as the output falls. The output high level is limited to about\n\\[\nV_{\\rm out,max}\\approx V_{DD}-V_{GS1},\n\\]\nso the stage is not rail-to-rail.\n\n### 2. Small-signal behavior\n\nIncluding body effect through \\(g_{mb1}\\), channel-length resistances \\(r_{o1},r_{o2}\\), and a load resistance \\(R_L\\) from output to ground,\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n=\n\\frac{g_{m1}}\n{g_{m1}+g_{mb1}+\\dfrac{1}{r_{o1}}+\\dfrac{1}{r_{o2}}+\\dfrac{1}{R_L}}\n\\approx 1.\n\\]\nIf the body of \\(M_1\\) is tied to its source, set \\(g_{mb1}=0\\). The gain is non-inverting and slightly less than unity; body effect and finite output resistance reduce it.\n\nThe output resistance is low:\n\\[\nR_{\\rm out}\n=\n\\frac{1}\n{g_{m1}+g_{mb1}+\\dfrac{1}{r_{o1}}+\\dfrac{1}{r_{o2}}+\\dfrac{1}{R_L}}\n\\approx \\frac{1}{g_{m1}+g_{mb1}}.\n\\]\nThe input resistance at low frequency is essentially infinite:\n\\[\nR_{\\rm in}\\approx\\infty\n\\]\nbecause it is a MOS gate.\n\nA change in the bias voltage \\(V_b\\) changes the output approximately as\n\\[\n\\frac{v_{\\rm out}}{v_b}\\approx -g_{m2}R_{\\rm out},\n\\]\ni.e. increasing the bias current pulls the output down.\n\n### 3. Summary of characteristics\n\n- **Function:** voltage buffer/source follower and DC level shifter.\n- **Polarity:** non-inverting.\n- **Voltage gain:** slightly below \\(1\\), ideally \\(\\approx1\\).\n- **Output impedance:** low, approximately \\(1/g_{m1}\\), so it can drive capacitive or low-resistance loads better than a high-impedance node.\n- **Input impedance:** very high, set mainly by gate capacitance.\n- **Output level:** \\(V_{\\rm out}\\approx V_{\\rm in}-V_{GS1}\\), so the high output is one \\(V_{GS}\\) below \\(V_{DD}\\); low output can approach ground only when the bias current falls/either transistor leaves saturation.\n- **Limitations:** reduced gain and nonlinearity from body effect/channel-length modulation; limited output swing; class-A static power consumption \\(P_{\\rm DC}\\approx I_QV_{DD}\\); requires \\(V_b>V_T\\) and sufficient headroom for \\(M_2\\) to remain a good current sink.",
        "format": "markdown",
        "sha256": "6ba492f52da6faf93ab5f292f65db78b04735df6a197b7a32b3daff5662395a6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower with M2 as a current-sink load, and gives the essential non-inverting gain at or slightly below unity. The body-effect and finite-output-resistance refinements are consistent with the golden solution.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 19271,
        "total_tokens": 19900,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18109,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 629,
        "output_tokens": 19271,
        "total_tokens": 19900,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18109,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **CMOS inverter** (complementary MOS inverter).  \n- **M1 (lower transistor): n-channel MOSFET, pull-down device.**\n- **M2 (upper transistor): p-channel MOSFET, pull-up device.**\n- The gates are connected together to \\(V_{\\rm in}\\), and the drains are connected together to \\(V_{\\rm out}\\).\n- Sources are connected to \\(0\\,\\mathrm V\\) and \\(V_{DD}\\), respectively.\n\n### 1. Logic operation\nAssuming enhancement-mode devices and \\(0\\le V_{\\rm in}\\le V_{DD}\\):\n\n| \\(V_{\\rm in}\\) | M1 (NMOS) | M2 (PMOS) | \\(V_{\\rm out}\\) |\n|---|---|---|---|\n| Low, \\(0\\) | OFF | ON | High, \\(\\approx V_{DD}\\) |\n| High, \\(V_{DD}\\) | ON | OFF | Low, \\(\\approx 0\\) |\n| Intermediate | partly ON | partly ON | switching region |\n\nThus\n\\[\nV_{\\rm out}\\approx \\overline{V_{\\rm in}}\n\\]\nso the circuit behaves as a digital inverter.\n\n- When \\(V_{\\rm in}=0\\), \\(V_{GS1}=0\\), so M1 is off.  \n  For M2, \\(V_{SG2}=V_{DD}\\), so M2 turns on and pulls \\(V_{\\rm out}\\) to \\(V_{DD}\\).\n- When \\(V_{\\rm in}=V_{DD}\\), \\(V_{SG2}=0\\), so M2 is off.  \n  M1 has \\(V_{GS1}=V_{DD}\\), turns on, and pulls \\(V_{\\rm out}\\) to ground.\n\n### 2. Voltage-transfer characteristic\nThe NMOS conducts when\n\\[\nV_{\\rm in}>V_{tn},\n\\]\nand the PMOS conducts when\n\\[\nV_{DD}-V_{\\rm in}>|V_{tp}|,\n\\]\ni.e.\n\\[\nV_{\\rm in}<V_{DD}-|V_{tp}|.\n\\]\n\nFor \\(0<V_{\\rm in}<V_{tn}\\), M1 is off and \\(V_{\\rm out}\\approx V_{DD}\\).  \nFor \\(V_{DD}-|V_{tp}|<V_{\\rm in}<V_{DD}\\), M2 is off and \\(V_{\\rm out}\\approx 0\\).  \nBetween these, both transistors can conduct, giving the steep switching transition.\n\nAt the switching threshold \\(V_M\\), both transistors are approximately in saturation, and their currents are equal:\n\\[\n\\frac12 K_n(V_M-V_{tn})^2\n=\n\\frac12 K_p(V_{DD}-V_M-|V_{tp}|)^2,\n\\]\nwhere\n\\[\nK_n=\\mu_n C_{\\rm ox}\\frac{W_n}{L_n},\\qquad\nK_p=\\mu_p C_{\\rm ox}\\frac{W_p}{L_p}.\n\\]\nThus\n\\[\nV_M=\n\\frac{V_{tn}+\\sqrt{\\frac{K_p}{K_n}}\\left(V_{DD}-|V_{tp}|\\right)}\n{1+\\sqrt{\\frac{K_p}{K_n}}}.\n\\]\n\nFor a symmetrical inverter,\n\\[\nK_n=K_p,\\qquad V_{tn}=|V_{tp}|,\n\\]\nso\n\\[\nV_M\\approx \\frac{V_{DD}}{2}.\n\\]\nIn practice, because \\(\\mu_n>\\mu_p\\), the PMOS is usually made wider so that\n\\[\n\\mu_n\\left(\\frac WL\\right)_n\n\\approx\n\\mu_p\\left(\\frac WL\\right)_p\n\\]\nfor a symmetric switching point.\n\n### 3. Currents and power\nWhen the input is held at a valid logic level, one transistor is off; ideally there is **no static current** except leakage:\n\\[\nP_{\\rm static}\\approx 0.\n\\]\nDuring switching, both transistors conduct briefly, producing a “crowbar” or short-circuit current from \\(V_{DD}\\) to ground. The main power in digital operation is dynamic:\n\\[\nP_{\\rm dyn}\\approx \\alpha C_L V_{DD}^2 f,\n\\]\nwhere \\(C_L\\) is the load capacitance, \\(f\\) is the switching frequency, and \\(\\alpha\\) is the activity factor. Leakage power is\n\\[\nP_{\\rm leak}\\approx V_{DD}I_{\\rm leak}.\n\\]\n\n### 4. Small-signal/analog behavior\nIf biased near \\(V_M\\), the circuit can also act as an inverting amplifier. Both gates are driven, so both transistors contribute transconductance. Its small-signal gain is approximately\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx -(g_{m1}+g_{m2})(r_{o1}\\parallel r_{o2}),\n\\]\nand its small-signal output resistance is\n\\[\nR_{\\rm out}\\approx r_{o1}\\parallel r_{o2}\n\\]\n(neglecting external load). The negative sign shows inversion.\n\n### Summary\n- The circuit is a **CMOS inverter**.\n- M1 is the NMOS pull-down; M2 is the PMOS pull-up.\n- It realizes \\(V_{\\rm out}=\\bar V_{\\rm in}\\) in digital operation.\n- It has nearly rail-to-rail output swing, low static power, high input resistance, and a steep switching characteristic around \\(V_M\\).\n- A symmetric design gives \\(V_M\\approx V_{DD}/2\\); the device widths can be adjusted to set the switching threshold and noise margins.",
        "format": "markdown",
        "sha256": "3b1a7653fe56875fd840455f132bd101615604b67a0df50d45a3b181e2838b40"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter and its NMOS pull-down and PMOS pull-up; the logic operation and supplemental analysis are consistent with the circuit.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 14877,
        "total_tokens": 15110,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 14877,
        "total_tokens": 15110,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **static CMOS inverter (NOT gate)**.\n\n- **\\(M_1\\)** is an n-channel enhancement MOSFET (pull-down device), source at ground.\n- **\\(M_2\\)** is a p-channel enhancement MOSFET (pull-up device), source at \\(V_{DD}\\).\n- The gates are tied to \\(V_{\\rm in}\\); the drains are tied to \\(V_{\\rm out}\\).\n\n### Logic operation\nFor valid logic levels:\n\n| \\(V_{\\rm in}\\) | \\(M_1\\) (nMOS) | \\(M_2\\) (pMOS) | \\(V_{\\rm out}\\) |\n|---|---|---|---|\n| LOW \\((\\approx 0)\\) | OFF | ON | HIGH \\((\\approx V_{DD})\\) |\n| HIGH \\((\\approx V_{DD})\\) | ON | OFF | LOW \\((\\approx 0)\\) |\n\nThus,\n\\[\nV_{\\rm out}=\\overline{V_{\\rm in}}\n\\]\nand the circuit realizes a CMOS inverter.\n\n### Transfer characteristic\nAssuming ideal enhancement devices with thresholds \\(V_{tn}>0\\) and \\(|V_{tp}|>0\\):\n\n1. **\\(V_{\\rm in}<V_{tn}\\)**  \n   \\(M_1\\) is off; \\(M_2\\) is on and holds the output high.  \n   \\[\n   V_{\\rm out}\\approx V_{DD}\n   \\]\n\n2. **\\(V_{tn}<V_{\\rm in}<V_M\\)**  \n   \\(M_1\\) begins conducting in saturation; \\(M_2\\) is still on (usually in triode). The output begins to fall. This is the high-gain transition region.\n\n3. **\\(V_{\\rm in}\\approx V_M\\)**  \n   Both transistors may conduct strongly. At the switching threshold the inverter has high voltage gain. For a symmetric inverter:\n   \\[\n   V_M\\approx \\frac{V_{DD}}{2}\n   \\]\n   The general long-channel expression is\n   \\[\n   V_M=\n   \\frac{V_{tn}+\\sqrt{\\frac{\\beta_p}{\\beta_n}}\n   \\left(V_{DD}-|V_{tp}|\\right)}\n   {1+\\sqrt{\\frac{\\beta_p}{\\beta_n}}},\n   \\qquad\n   \\beta=\\mu C_{ox}\\frac{W}{L}.\n   \\]\n   Making the nMOS and pMOS strengths equal gives \\(V_M=V_{DD}/2\\). Because hole mobility is lower, the pMOS is usually made wider than the nMOS.\n\n4. **\\(V_M<V_{\\rm in}<V_{DD}-|V_{tp}|\\)**  \n   \\(M_1\\) is on, \\(M_2\\) is still on; the output continues falling rapidly.\n\n5. **\\(V_{\\rm in}>V_{DD}-|V_{tp}|\\)**  \n   \\(M_2\\) is off; \\(M_1\\) is on and pulls the output low:\n   \\[\n   V_{\\rm out}\\approx 0.\n   \\]\n\nThe DC output current is found by equating the nMOS and pMOS currents:\n\\[\nI_{D,M1}=I_{D,M2}.\n\\]\nAt valid logic inputs one transistor is off, so the ideal quiescent current is essentially zero.\n\n### Important properties\n- **Rail-to-rail output:** \\(V_{OH}\\approx V_{DD}\\), \\(V_{OL}\\approx 0\\).\n- **Very high input impedance:** the gate draws only capacitive/leakage current.\n- **No ideal static power** with a valid fixed input; power is mainly dynamic:\n  \\[\n  P_{\\rm dyn}\\approx \\alpha C_L V_{DD}^2 f\n  \\]\n  plus short-circuit power during switching, when both transistors are momentarily on.\n- **Noise margins:**\n  \\[\n  NM_H=V_{OH}-V_{IH},\\qquad\n  NM_L=V_{IL}-V_{OL}.\n  \\]\n  They are maximized when the inverter is designed symmetrically, with \\(V_M\\approx V_{DD}/2\\). For a simple matched long-channel model with \\(V_{tn}=|V_{tp}|=V_T\\),\n  \\[\n  V_{IL}\\approx\\frac{3V_{DD}+2V_T}{8},\\quad\n  V_{IH}\\approx\\frac{5V_{DD}-2V_T}{8},\n  \\]\n  giving equal high and low noise margins.\n\nSo the circuit is the basic **CMOS inverter/NOT gate**, the fundamental building block of CMOS digital logic. An input left floating or biased near mid-supply is undesirable because both transistors can conduct, producing a large crowbar current.",
        "format": "markdown",
        "sha256": "d1c731e49d373d072c8822f17a8e1ae3ff68dc0f94beaf5c1c779df2f304340e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter and its NMOS pull-down, PMOS pull-up, and logic operation. The additional analysis is consistent with inverter behavior; the golden solution explicitly awards full credit for this identification.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 16698,
        "total_tokens": 16931,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 16698,
        "total_tokens": 16931,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15727,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **CMOS inverter** (logic NOT gate).\n\n- \\(M_1\\): n-channel MOSFET connected between the output and ground; it acts as the **pull-down** device.\n- \\(M_2\\): p-channel MOSFET connected between \\(V_{DD}\\) and the output; it acts as the **pull-up** device.\n- The gates of \\(M_1\\) and \\(M_2\\) are tied together to \\(V_{\\text{in}}\\).\n- The drains are tied together to \\(V_{\\text{out}}\\).\n\n### Operation\nNeglecting leakage,\n\n\\[\nM_1 \\text{ is ON when } V_{\\text{in}}>V_{TN}\n\\]\n\n\\[\nM_2 \\text{ is ON when } V_{DD}-V_{\\text{in}}>|V_{TP}|\n\\quad \\text{i.e. } V_{\\text{in}}<V_{DD}-|V_{TP}|\n\\]\n\n| \\(V_{\\text{in}}\\) | \\(M_1\\) (nMOS) | \\(M_2\\) (pMOS) | \\(V_{\\text{out}}\\) |\n|---|---|---|---|\n| Low, \\(\\approx 0\\) | OFF | ON | High, \\(\\approx V_{DD}\\) |\n| High, \\(\\approx V_{DD}\\) | ON | OFF | Low, \\(\\approx 0\\) |\n| Intermediate | may be ON | may be ON | transition region |\n\nThus,\n\n\\[\nV_{\\text{out}}=\\overline{V_{\\text{in}}}\n\\]\n\nand the circuit implements a digital inverter.\n\n### Voltage transfer characteristic\n- For \\(V_{\\text{in}}\\) near \\(0\\), output is pulled to \\(V_{DD}\\) through \\(M_2\\).\n- For \\(V_{\\text{in}}\\) near \\(V_{DD}\\), output is pulled to ground through \\(M_1\\).\n- In between, both transistors can conduct; the output changes rapidly from high to low, giving an inverting, high-gain transfer characteristic.\n\nThe switching threshold \\(V_M\\) (where \\(V_{\\text{in}}=V_{\\text{out}}\\)) is approximately, assuming both devices are in saturation at switching,\n\n\\[\nV_M\n=\n\\frac{V_{DD}-|V_{TP}|+\\sqrt{\\frac{\\beta_n}{\\beta_p}}V_{TN}}\n{1+\\sqrt{\\frac{\\beta_n}{\\beta_p}}}\n\\]\n\nwhere \\(\\beta=\\mu C_{ox}W/L\\).  \nFor a symmetric inverter,\n\n\\[\n\\beta_n=\\beta_p,\\quad V_{TN}=|V_{TP}|\n\\quad\\Rightarrow\\quad\nV_M\\approx \\frac{V_{DD}}{2}.\n\\]\n\nIn practice, because electron mobility is larger than hole mobility, the pMOS is usually made wider than the nMOS to obtain a symmetric switching point.\n\n### Power and impedance\n- In steady logic high or low, one transistor is OFF, so there is ideally **no DC path** from \\(V_{DD}\\) to ground. Static power is therefore very small, only leakage.\n- During switching, both transistors are briefly ON, causing a short-circuit current. Additional power is required to charge/discharge the output capacitance:\n\n\\[\nP_{\\text{dyn}}\\approx \\alpha C_L V_{DD}^2 f\n\\]\n\nplus a short-circuit component.\n- The input is a MOS gate, so its DC input resistance is extremely high.\n- The output is driven through the ON resistance of \\(M_1\\) or \\(M_2\\).\n\n### Noise margins\nFor an ideal symmetric CMOS inverter, \\(V_{OH}\\approx V_{DD}\\), \\(V_{OL}\\approx0\\), and the noise margins are approximately half the supply voltage each:\n\n\\[\nNM_H \\approx NM_L \\approx \\frac{V_{DD}}{2}\n\\]\n\nin an ideal abrupt-switch model. In a real MOS inverter, they are obtained from the transfer characteristic where the slope is \\(-1\\), and are somewhat smaller.\n\n**Summary:** The circuit is a CMOS inverter/NOT gate: input low gives output high through the pMOS; input high gives output low through the nMOS. It has rail-to-rail output levels, very low static power, high input impedance, and is the fundamental building block of CMOS digital logic.",
        "format": "markdown",
        "sha256": "ea4738a861b747eeb8de2ea86bcf359bad7df985528a508c79132cc1ffeae572"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter and its NMOS pull-down, PMOS pull-up, and complementary operation. The additional analysis is consistent with the circuit and does not contradict its operation.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 11423,
        "total_tokens": 11656,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10548,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 11423,
        "total_tokens": 11656,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10548,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **CMOS inverter** (assuming the usual symbol convention: upper device \\(M_1\\) is p-channel, lower device \\(M_2\\) is n-channel). Both gates are driven by the same input \\(V_{\\rm in}\\), and the drains are joined at the output \\(V_{\\rm out}\\).\n\n### Operation\n- **\\(V_{\\rm in}\\) LOW \\((\\approx 0\\,\\mathrm V)\\):**  \n  \\(M_2\\) is OFF, \\(M_1\\) is ON. The output is pulled to \\(V_{DD}\\).  \n  \\[\n  V_{\\rm out}\\approx V_{DD}\\quad(\\text{logic }1)\n  \\]\n- **\\(V_{\\rm in}\\) HIGH \\((\\approx V_{DD})\\):**  \n  \\(M_1\\) is OFF, \\(M_2\\) is ON. The output is pulled to ground.  \n  \\[\n  V_{\\rm out}\\approx 0\\quad(\\text{logic }0)\n  \\]\n- **Intermediate input:** both transistors can be ON briefly. The output moves sharply from \\(V_{DD}\\) to 0 around the switching threshold, so the circuit acts as an inverting voltage amplifier in this region.\n\nThus the ideal logic relation is\n\\[\nV_{\\rm out}=\\overline{V_{\\rm in}}.\n\\]\n\n### Threshold conditions\nFor n-channel \\(M_2\\):\n\\[\nV_{\\rm GS2}=V_{\\rm in},\\qquad\nM_2\\text{ ON if }V_{\\rm in}>V_{Tn}.\n\\]\nFor p-channel \\(M_1\\):\n\\[\nV_{\\rm SG1}=V_{DD}-V_{\\rm in},\\qquad\nM_1\\text{ ON if }V_{DD}-V_{\\rm in}>|V_{Tp}|,\n\\]\nor\n\\[\nV_{\\rm in}<V_{DD}-|V_{Tp}|.\n\\]\n\n### Switching point\nAt the switching threshold \\(V_M\\), both transistors are typically in saturation and their currents are equal:\n\\[\n\\frac12\\beta_n(V_M-V_{Tn})^2\n=\n\\frac12\\beta_p(V_{DD}-V_M-|V_{Tp}|)^2,\n\\]\nso\n\\[\nV_M=\n\\frac{V_{Tn}+\\sqrt{\\frac{\\beta_p}{\\beta_n}}\\,\n\\bigl(V_{DD}-|V_{Tp}|\\bigr)}\n{1+\\sqrt{\\frac{\\beta_p}{\\beta_n}}}.\n\\]\nFor a symmetric inverter, \\(V_{Tn}=|V_{Tp}|\\) and \\(\\beta_n=\\beta_p\\), giving\n\\[\nV_M=\\frac{V_{DD}}{2}.\n\\]\n\nThe voltage-transfer characteristic is therefore inverting with a steep transition around \\(V_M\\):\n- \\(V_{\\rm out}\\approx V_{DD}\\) for low \\(V_{\\rm in}\\),\n- sharp fall near \\(V_M\\),\n- \\(V_{\\rm out}\\approx 0\\) for high \\(V_{\\rm in}\\).\n\n### Small-signal behavior\nWhen biased near \\(V_M\\), the circuit behaves as a CMOS amplifier with high small-signal gain:\n\\[\nA_v\\simeq\n-\\frac{g_{m1}+g_{m2}}{g_{ds1}+g_{ds2}}.\n\\]\nIn an ideal CMOS process with negligible output conductance, the gain can be very large; in practice it is finite.\n\n### Power and characteristics\n- In steady logic states, ideally **one transistor is OFF**, so static power is nearly zero.\n- Power is consumed mainly during switching:\n  \\[\n  P_{\\rm dyn}\\approx \\alpha C_L V_{DD}^{2}f\n  \\]\n  plus short-circuit and leakage power.\n- Input impedance is very high (gate capacitance); output impedance is low in either steady logic state.\n- Output swing is essentially rail-to-rail: \\(0\\) to \\(V_{DD}\\).\n\nSo, functionally, the circuit is a **CMOS logic inverter** and, when biased at its switching point, also a high-gain inverting amplifier. If the diagram is interpreted as having two identical n-channel devices instead, then it is not a true CMOS inverter: at low input both devices would be OFF and the output would float, while at high input both conduct and the output is set by a resistive ratio.",
        "format": "markdown",
        "sha256": "e3fcbb3b4799a8999d4d2109403f9c7ef23eb7113860c4dbae8378010e1db68e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer identifies the upper device as p-channel and analyzes the circuit as a conventional CMOS inverter. The golden solution requires recognizing both devices as NMOS; its conditional caveat does not correct the main analysis.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 13088,
        "total_tokens": 13333,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12198,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 13088,
        "total_tokens": 13333,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12198,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **CMOS inverter**—a digital **NOT gate**—assuming the upper transistor \\(M_1\\) is a p-channel MOSFET and the lower transistor \\(M_2\\) is an n-channel MOSFET.\n\n\\[\nV_{\\text{out}}=\\overline{V_{\\text{in}}}\n\\]\n\n### Operation\n- **\\(V_{\\text{in}}=0\\) (logic LOW):**\n  - \\(M_2\\) is OFF because \\(V_{GS,n}=0<V_{TN}\\).\n  - \\(M_1\\) is ON because \\(V_{SG,p}=V_{DD}>|V_{TP}|\\).\n  - \\(V_{\\text{out}}\\) is pulled up to approximately \\(V_{DD}\\) (logic HIGH).\n  - In the ideal case there is no dc current from \\(V_{DD}\\) to ground.\n\n- **\\(V_{\\text{in}}=V_{DD}\\) (logic HIGH):**\n  - \\(M_1\\) is OFF because \\(V_{SG,p}=0< |V_{TP}|\\).\n  - \\(M_2\\) is ON because \\(V_{GS,n}=V_{DD}>V_{TN}\\).\n  - \\(V_{\\text{out}}\\) is pulled down to approximately \\(0\\ \\text{V}\\) (logic LOW).\n  - Again, no ideal static current flows.\n\n- **Intermediate \\(V_{\\text{in}}\\):**\n  - Both transistors can be ON when\n    \\[\n    V_{TN}<V_{\\text{in}}<V_{DD}-|V_{TP}|.\n    \\]\n  - This is the transition region of the voltage-transfer characteristic. A direct current can flow briefly through the supply-to-ground path, producing **short-circuit power** during switching.\n  - For symmetric devices, the switching threshold is approximately\n    \\[\n    V_M \\approx \\frac{V_{DD}}{2}.\n    \\]\n    More generally, if both devices are saturated at switching,\n    \\[\n    V_M=\n    \\frac{V_{TN}+\\sqrt{\\frac{\\beta_p}{\\beta_n}}\\left(V_{DD}-|V_{TP}|\\right)}\n    {1+\\sqrt{\\frac{\\beta_p}{\\beta_n}}},\n    \\]\n    where \\(\\beta=\\mu C_{ox}(W/L)\\).\n\n### Truth table\n\\[\n\\begin{array}{c|c}\nV_{\\text{in}} & V_{\\text{out}}\\\\\\hline\n0 & V_{DD}\\ (\\text{HIGH})\\\\\nV_{DD} & 0\\ (\\text{LOW})\n\\end{array}\n\\]\n\n### Important characteristics\n- **Logic function:** inversion, \\(Y=\\bar{A}\\).\n- **Ideal output levels:** \\(V_{OH}=V_{DD}\\), \\(V_{OL}=0\\).\n- **Static power:** very small in steady logic states; only leakage in real devices.\n- **Dynamic power:** mainly\n  \\[\n  P_{\\text{dyn}}\\approx \\alpha C_L V_{DD}^2 f,\n  \\]\n  plus short-circuit power during transitions.\n- **Delay:** high-to-low output transition is mainly through \\(M_2\\); low-to-high transition is mainly through \\(M_1\\). The pMOS is often made wider to compensate for lower hole mobility.\n- At the switching point the circuit can act as an inverting amplifier, but digital use avoids continuous biasing in this high-current region.\n\nSo the circuit functions as a **CMOS inverter/NOT gate**, producing a logic-high output for a low input and a logic-low output for a high input.",
        "format": "markdown",
        "sha256": "a8d6fc5fec01b1c4569860e07b09d9ceac40758a4612bb3be983ce58d47d2122"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly identifies M1 as pMOS and analyzes the circuit as an ordinary CMOS inverter; the golden solution requires recognizing both devices as NMOS.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 11434,
        "total_tokens": 11679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10231,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 11434,
        "total_tokens": 11679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10231,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **CMOS inverter** (assuming the usual convention: upper transistor \\(M_1\\) is p-channel and lower transistor \\(M_2\\) is n-channel).\n\n### 1. Connections and device roles\n- \\(M_1\\): pMOS, source at \\(V_{DD}\\), drain at \\(V_\\text{out}\\), gate at \\(V_\\text{in}\\).\n- \\(M_2\\): nMOS, source at ground, drain at \\(V_\\text{out}\\), gate at \\(V_\\text{in}\\).\n- Both gates are tied together; both drains are tied together. The output is taken from the common drain node.\n\n### 2. Static operation\nLet \\(V_{TN}\\) be the nMOS threshold voltage and \\(V_{TP}=|V_{tp}|\\) be the magnitude of the pMOS threshold voltage.\n\n| \\(V_\\text{in}\\) | \\(M_1\\) (pMOS) | \\(M_2\\) (nMOS) | \\(V_\\text{out}\\) |\n|---|---|---|---|\n| Low, \\(V_\\text{in}<V_{TN}\\) | ON | OFF | High \\(\\approx V_{DD}\\) |\n| High, \\(V_\\text{in}>V_{DD}-V_{TP}\\) | OFF | ON | Low \\(\\approx 0\\) |\n| Intermediate | ON | ON | Determined by drive strengths |\n\nSo the circuit performs logic inversion:\n\\[\nV_\\text{out} = \\overline{V_\\text{in}}\n\\]\nfor digital input levels \\(0\\) and \\(V_{DD}\\).\n\nIn steady state with \\(V_\\text{in}=0\\) or \\(V_\\text{in}=V_{DD}\\), one transistor is off, so ideally no direct current flows from \\(V_{DD}\\) to ground. Only leakage current is present; hence static power dissipation is very small.\n\n### 3. Voltage transfer characteristic\nFor a slowly varying input:\n\n- For \\(V_\\text{in}<V_{TN}\\): \\(M_2\\) is cut off; \\(M_1\\) is on and charges the output to \\(V_{DD}\\).\n- For \\(V_\\text{in}>V_{DD}-V_{TP}\\): \\(M_1\\) is cut off; \\(M_2\\) is on and discharges the output to \\(0\\).\n- In the transition region, both devices may be on. The output changes rapidly from \\(V_{DD}\\) to \\(0\\); the inverter has high voltage gain in this region, so it can also be used as an amplifier if biased near the switching point.\n\nThe switching threshold \\(V_M\\) is found by equating the saturation currents of the two devices:\n\\[\n\\frac{\\beta_n}{2}(V_M-V_{TN})^2\n=\n\\frac{\\beta_p}{2}(V_{DD}-V_M-|V_{TP}|)^2\n\\]\nwhere\n\\[\n\\beta_n=\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_n,\\qquad\n\\beta_p=\\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_p.\n\\]\nThus\n\\[\nV_M=\n\\frac{V_{TN}+\\sqrt{\\frac{\\beta_p}{\\beta_n}}\\,\n\\left(V_{DD}-|V_{TP}|\\right)}\n{1+\\sqrt{\\frac{\\beta_p}{\\beta_n}}}.\n\\]\nFor a symmetric inverter with \\(\\beta_n=\\beta_p\\) and \\(V_{TN}=|V_{TP}|\\):\n\\[\nV_M=\\frac{V_{DD}}{2}.\n\\]\n\n### 4. Current and power\n- During the high-to-low or low-to-high transition, both transistors can be on simultaneously, causing a brief “crowbar” current from \\(V_{DD}\\) to ground.\n- The average dynamic power is approximately\n\\[\nP_\\text{dyn}\\approx \\alpha C_L V_{DD}^2 f\n\\]\nplus short-circuit power, where \\(\\alpha\\) is the switching activity, \\(C_L\\) the load capacitance, and \\(f\\) the clock/input frequency.\n- Static power is only leakage:\n\\[\nP_\\text{static}\\approx I_\\text{leak}V_{DD}.\n\\]\n\n### 5. Important properties\n- Rail-to-rail output swing: \\(V_{OH}\\approx V_{DD}\\), \\(V_{OL}\\approx 0\\).\n- High input resistance (MOS gates).\n- Low static power.\n- The output is inverted relative to the input.\n- Speed is limited by charging/discharging the load and internal capacitances.\n- If the upper device were not pMOS (or the lower not nMOS), the circuit would not operate as a proper CMOS inverter; in particular, a low input would leave the output floating or undefined.\n\nIn short, the circuit is a **CMOS logic inverter** with a sharp voltage-transfer characteristic and negligible static power consumption.",
        "format": "markdown",
        "sha256": "661a51fb00cc4da4cb0994672b0142aa7d775217ad7eb2d2a853bae9715525d4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the upper device as pMOS and analyzes the circuit as a conventional CMOS inverter; the golden solution requires both devices to be identified as NMOS.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 16158,
        "total_tokens": 16403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15146,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 16158,
        "total_tokens": 16403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15146,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **ratioed inverter/active-load inverter** with a diode-connected PMOS load.\n\n### 1. Circuit identification\n- **M1** is an NMOS driver: source at ground, drain at \\(V_{\\rm out}\\), gate at \\(V_{\\rm in}\\).\n- **M2** is a PMOS load: source at \\(V_{DD}\\), drain at \\(V_{\\rm out}\\), and its gate is tied to its drain.\n- Because M2’s gate is shorted to its drain, M2 is **diode-connected**. When it is on, it operates in saturation, so its small-signal resistance is approximately \\(1/g_{m2}\\).\n\nThe logic function is **inversion**:\n\\[\nV_{\\rm out} = \\overline{V_{\\rm in}}\n\\]\nbut with degraded levels and nonzero static power.\n\n### 2. DC operation\nLet \\(V_{TN}\\) be the NMOS threshold and \\(V_{TP}\\) the magnitude of the PMOS threshold.\n\n**When \\(V_{\\rm in}\\) is low:** M1 is off. M2 pulls \\(V_{\\rm out}\\) up until the PMOS reaches threshold:\n\\[\nV_{\\rm OH} \\approx V_{DD}-V_{TP}\n\\]\nIdeally, no static current flows after settling.\n\n**When \\(V_{\\rm in}\\) is high:** M1 is on and pulls \\(V_{\\rm out}\\) down. Both M1 and M2 conduct, so the inverter draws static current. The low level is determined by the strength ratio \\(\\beta_N/\\beta_P\\):\n\\[\n\\frac{\\beta_P}{2}(V_{DD}-V_{TP}-V_{\\rm OL})^2\n=\n\\beta_N\\left[(V_{\\rm in}-V_{TN})V_{\\rm OL}-\\frac{V_{\\rm OL}^2}{2}\\right]\n\\]\nwith \\(V_{\\rm in}=V_{DD}\\) for a valid low level. If \\(\\beta_N\\gg\\beta_P\\), \\(V_{\\rm OL}\\approx 0\\); otherwise \\(V_{\\rm OL}\\) is significant.\n\n### 3. Voltage transfer characteristic\nFor long-channel devices, the inverter current balance is:\n\\[\nI_{D2}=I_{D1}\n\\]\nwhere\n\\[\nI_{D2}=\\frac{\\beta_P}{2}(V_{DD}-V_{TP}-V_{\\rm out})^2\n\\]\nwhen M2 is on, i.e. \\(V_{\\rm out}<V_{DD}-V_{TP}\\).\n\nThe NMOS is in saturation when\n\\[\nV_{\\rm out}>V_{\\rm in}-V_{TN},\n\\]\nand in linear when\n\\[\nV_{\\rm out}<V_{\\rm in}-V_{TN}.\n\\]\nThus:\n- For \\(V_{\\rm in}<V_{TN}\\), M1 is off and \\(V_{\\rm out}\\approx V_{DD}-V_{TP}\\).\n- For \\(V_{\\rm in}\\) just above \\(V_{TN}\\), both transistors are saturated, giving\n  \\[\n  V_{\\rm out}=V_{DD}-V_{TP}\n  -\\sqrt{\\frac{\\beta_N}{\\beta_P}}\\,(V_{\\rm in}-V_{TN}).\n  \\]\n  The slope is\n  \\[\n  \\frac{dV_{\\rm out}}{dV_{\\rm in}}\n  =-\\sqrt{\\frac{\\beta_N}{\\beta_P}}.\n  \\]\n- For larger \\(V_{\\rm in}\\), M1 enters the linear region and the VTC becomes nonlinear.\n\nThe switching threshold \\(V_M\\) defined by \\(V_{\\rm in}=V_{\\rm out}\\) is approximately\n\\[\nV_M=\n\\frac{V_{DD}-V_{TP}+\\sqrt{\\beta_N/\\beta_P}\\,V_{TN}}\n{1+\\sqrt{\\beta_N/\\beta_P}},\n\\]\nprovided \\(V_{DD}>V_{TN}+V_{TP}\\).\n\n### 4. Small-signal gain\nIn the saturated region, the small-signal voltage gain is\n\\[\nA_v \\approx -\\frac{g_{mN}}{g_{mP}}\n\\approx -\\sqrt{\\frac{\\beta_N}{\\beta_P}},\n\\]\nincluding finite output resistance:\n\\[\nA_v \\approx -g_{mN}\\left(r_{oN}\\parallel r_{oP}\\parallel \\frac{1}{g_{mP}}\\right).\n\\]\nThe diode-connected PMOS provides a low load resistance, so the gain is relatively low.\n\n### 5. Important limitations\n- **Reduced high level:** \\(V_{\\rm OH}\\approx V_{DD}-V_{TP}\\), not \\(V_{DD}\\).\n- **Ratio-dependent low level:** To get a small \\(V_{\\rm OL}\\), the NMOS must be much stronger than the PMOS.\n- **Static power:** When \\(V_{\\rm in}\\) is high, both transistors are on, so current flows from \\(V_{DD}\\) to ground.\n- **Poor noise margins:** The asymmetric VTC and degraded levels give low noise margins.\n- **Not a standard CMOS inverter:** In a standard CMOS inverter, both gates are tied to the input; here the PMOS gate is tied to the output, making it a diode-connected active load.\n\nIn summary, the circuit is a **diode-connected load inverter** that inverts the input but with a degraded high level, ratio-dependent low level, and nonzero static power when the output is low. It is useful in simple analog/active-load circuits but is not preferred for high-performance digital logic.",
        "format": "markdown",
        "sha256": "a11e7f5a017d5b44baee684d92b5359bcd5ba55c04f6a6720b3b13fff292c486"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain with both devices’ output resistances included consistently. The additional operating-point discussion does not undermine the essential answer.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 23070,
        "total_tokens": 23315,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 23070,
        "total_tokens": 23315,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the usual enhancement-MOSFET symbols, the circuit is:\n\n- **M1:** n-channel MOSFET, source grounded, gate driven by \\(V_{\\rm in}\\), drain at \\(V_{\\rm out}\\).\n- **M2:** p-channel MOSFET, source at \\(V_{DD}\\), drain at \\(V_{\\rm out}\\), with its **gate connected to its drain**. Thus M2 is a **diode-connected PMOS active load**.\n\nSo the circuit is an **NMOS common-source stage with a diode-connected PMOS load**. It behaves as an inverting amplifier/logic inverter, but it is a **ratioed** circuit, not a complementary CMOS inverter. If a standard CMOS inverter were intended, the gate of M2 would be connected to \\(V_{\\rm in}\\), not to \\(V_{\\rm out}\\).\n\nLet  \n\\[\nK_n=\\frac12\\mu_n C_{ox}\\frac{W_1}{L_1},\\qquad\nK_p=\\frac12\\mu_p C_{ox}\\frac{W_2}{L_2},\n\\]\nand let \\(V_{tn}>0\\), \\(V_{tp}<0\\). Use \\(V_{TP}=|V_{tp}|\\).\n\n### DC operation\nIgnoring channel-length modulation and body effect, the currents in the saturated region are\n\\[\nI_{D1}=K_n(V_{\\rm in}-V_{tn})^2,\n\\]\n\\[\nI_{D2}=K_p(V_{DD}-V_{\\rm out}-V_{TP})^2.\n\\]\nWhen both are conducting, KCL gives\n\\[\nK_n(V_{\\rm in}-V_{tn})^2\n=\nK_p(V_{DD}-V_{\\rm out}-V_{TP})^2.\n\\]\n\nThe pulled-up high output is limited by the PMOS threshold:\n\\[\nV_{OH}\\approx V_{DD}-V_{TP}.\n\\]\nThis is because M2 turns off when \\(V_{SG2}=V_{DD}-V_{\\rm out}\\lesssim V_{TP}\\).\n\nFor the region where M1 is in saturation and M2 is on,\n\\[\nV_{\\rm out}\n=\nV_{DD}-V_{TP}\n-\n\\sqrt{\\frac{K_n}{K_p}}\\,(V_{\\rm in}-V_{tn}).\n\\]\nThus the voltage-transfer characteristic is **inverting**. The switching threshold, using \\(V_{\\rm out}=V_{\\rm in}\\), is approximately\n\\[\nV_M=\n\\frac{V_{DD}-V_{TP}\n+\\sqrt{K_n/K_p}\\,V_{tn}}\n{1+\\sqrt{K_n/K_p}}.\n\\]\n\nWhen \\(V_{\\rm in}\\) becomes high enough, M1 enters the triode region and the low output is found from\n\\[\nK_n[2(V_{\\rm in}-V_{tn})V_{\\rm out}-V_{\\rm out}^2]\n=\nK_p(V_{DD}-V_{\\rm out}-V_{TP})^2.\n\\]\nFor \\(V_{\\rm in}=V_{DD}\\) and small \\(V_{OL}\\), an approximation is\n\\[\nV_{OL}\\approx\n\\frac{K_p(V_{DD}-V_{TP})^2}\n{2K_n(V_{DD}-V_{tn})}.\n\\]\nSo \\(V_{OL}\\) is made smaller by making M1 stronger than M2, i.e. \\(K_n\\gg K_p\\), but this also shifts the switching threshold.\n\n### Small-signal behavior\nIn the saturated amplifier region, the small-signal gain is\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx\n-\\frac{g_{m1}}{g_{m2}}\n\\approx\n-\\sqrt{\\frac{\\mu_n(W/L)_1}{\\mu_p(W/L)_2}},\n\\]\nwith sign showing inversion. Including output resistances,\n\\[\nA_v\\approx\n-\\frac{g_{m1}}{g_{m2}+1/r_{o1}+1/r_{o2}},\n\\]\nand\n\\[\nR_{\\rm out}\\approx r_{o1}\\parallel r_{o2}\\parallel \\frac{1}{g_{m2}}.\n\\]\nThe diode-connected load has a comparatively low resistance, so this stage has only moderate gain; a true current-source or cascode load would give higher gain.\n\n### Logic behavior\n- \\(V_{\\rm in}\\) low: M1 is off; M2 pulls/holds the output high, approximately \\(V_{OH}=V_{DD}-|V_{tp}|\\).\n- \\(V_{\\rm in}\\) high: M1 turns on and pulls the output low; current still flows through M2, so the circuit dissipates static power in the low-output state.\n- Therefore it performs inversion, but with a degraded high level and ratioed logic behavior.\n\nIn short: **the circuit is an inverting NMOS stage with a diode-connected PMOS load—an active-load inverter/common-source amplifier.** It is not a complementary CMOS inverter unless M2’s gate is connected to \\(V_{\\rm in}\\) instead of \\(V_{\\rm out}\\).",
        "format": "markdown",
        "sha256": "153827b621236dc1c2d7aa93e41e20cd72550c7236e8f8882493c41ed871c35e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the NMOS common-source stage with a diode-connected PMOS load and gives the inverting gain both without and with consistent output-resistance terms. The extra large-signal discussion does not undermine the essential answer.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 384,
        "input_tokens": 393,
        "output_tokens": 27485,
        "total_tokens": 27878,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26427,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 384,
        "input_tokens": 393,
        "output_tokens": 27485,
        "total_tokens": 27878,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26427,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a simple **inverter/amplifier** consisting of an **NMOS driver** (\\(M_1\\)) and a **diode-connected PMOS load** (\\(M_2\\)).  \n\n- \\(M_1\\) is an NMOS transistor whose source is grounded and whose gate is driven by \\(V_{in}\\).  \n- \\(M_2\\) is a PMOS transistor whose source is connected to \\(V_{DD}\\), whose drain is connected to \\(V_{out}\\), and whose gate is tied to its drain. Thus \\(M_2\\) is diode-connected and always operates in saturation.\n\n---\n\n## 1. Operating regions\n\nLet \\(V_{Tn}\\) be the NMOS threshold, and let \\(V_{TP}=|V_{Tp}|\\) be the magnitude of the PMOS threshold.\n\n- **\\(M_1\\)**:\n  - Off when \\(V_{in}<V_{Tn}\\).\n  - In saturation when \\(V_{in}>V_{Tn}\\) and \\(V_{out}>V_{in}-V_{Tn}\\).\n  - In triode when \\(V_{in}>V_{Tn}\\) and \\(V_{out}<V_{in}-V_{Tn}\\).\n\n- **\\(M_2\\)**:\n  - It is on when \\(V_{out}<V_{DD}-V_{TP}\\).\n  - Because it is diode-connected, \\(V_{SD}=V_{SG}=V_{DD}-V_{out}\\), so it is always in saturation when on.\n\n---\n\n## 2. Voltage transfer characteristic (VTC)\n\nLet  \n\\[\nk_n=\\frac12\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_n,\\qquad\nk_p=\\frac12\\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_p\n\\]\nand define\n\\[\nr=\\sqrt{\\frac{k_n}{k_p}}.\n\\]\n\n### Region 1: \\(V_{in}<V_{Tn}\\)\n\\(M_1\\) is off. The only current is the PMOS current, which must be zero, so \\(M_2\\) is at threshold. Hence\n\\[\n\\boxed{V_{out}=V_{DD}-V_{TP}}\\equiv V_{OH}.\n\\]\nThis is the output high level. It is degraded by \\(V_{TP}\\) and is not full \\(V_{DD}\\).\n\n### Region 2: \\(V_{in}>V_{Tn}\\), \\(M_1\\) in saturation\nBoth transistors are in saturation. Equating currents:\n\\[\nk_p(V_{DD}-V_{out}-V_{TP})^2\n=\nk_n(V_{in}-V_{Tn})^2.\n\\]\nThus\n\\[\n\\boxed{V_{out}=V_{DD}-V_{TP}-r(V_{in}-V_{Tn})}.\n\\]\nThis is a **linear region** with slope \\(-r\\). The small-signal gain is\n\\[\n\\boxed{A_v=-\\frac{g_{m1}}{g_{m2}}=-r=-\\sqrt{\\frac{k_n}{k_p}}}.\n\\]\n\nThis region is valid while\n\\[\nV_{out}>V_{in}-V_{Tn},\n\\]\ni.e.\n\\[\nV_{in}<V_{Tn}+\\frac{V_{DD}-V_{TP}}{1+r}.\n\\]\n\n### Region 3: \\(V_{in}>V_{Tn}+\\frac{V_{DD}-V_{TP}}{1+r}\\), \\(M_1\\) in triode\n\\(M_1\\) enters the triode region. The output is found by solving\n\\[\nk_p(V_{DD}-V_{out}-V_{TP})^2\n=\nk_n\\left[2(V_{in}-V_{Tn})V_{out}-V_{out}^2\\right].\n\\]\nFor \\(V_{in}=V_{DD}\\), the output low level \\(V_{OL}\\) is approximately\n\\[\n\\boxed{V_{OL}\\approx\n\\frac{k_p(V_{DD}-V_{TP})^2}{2k_n(V_{DD}-V_{Tn})}}\n\\]\nfor small \\(V_{OL}\\). The exact value is obtained by solving the above quadratic equation.\n\n---\n\n## 3. Switching threshold \\(V_M\\)\n\nThe switching threshold occurs when \\(V_{in}=V_{out}=V_M\\). Both transistors are in saturation, so\n\\[\nk_n(V_M-V_{Tn})^2\n=\nk_p(V_{DD}-V_M-V_{TP})^2.\n\\]\nTaking square roots,\n\\[\n\\boxed{V_M=\\frac{V_{DD}-V_{TP}+r\\,V_{Tn}}{1+r}}.\n\\]\nIf \\(V_{Tn}=V_{TP}\\) and \\(r=1\\) (i.e. \\(k_n=k_p\\)), then \\(V_M=V_{DD}/2\\).\n\n---\n\n## 4. Summary of the circuit behavior\n\n- **Inverting amplifier:** The circuit is an inverting amplifier. The gain in the transition region is \\(-\\sqrt{k_n/k_p}\\).\n- **Diode-connected load:** The PMOS load \\(M_2\\) is always in saturation and provides a nonlinear load. Its small-signal resistance is \\(1/g_{m2}\\).\n- **Ratioed inverter:** The transistor sizes (ratio \\(k_n/k_p\\)) determine the switching threshold, output high level, and output low level. The output high level is \\(V_{DD}-V_{TP}\\), not full \\(V_{DD}\\).\n- **Static power:** When \\(V_{in}\\) is low, \\(M_1\\) is off and no static current flows. When \\(V_{in}\\) is high, both \\(M_1\\) and \\(M_2\\) are on, so a static current flows from \\(V_{DD}\\) to ground. This is a ratioed inverter, unlike a CMOS inverter which has no static power.\n- **Application:** It is used as a simple analog inverter/amplifier and in some ratioed logic circuits. It is not a standard CMOS inverter because the output levels are not rail-to-rail and it has static power consumption in the high-input state.\n\nThe voltage transfer characteristic is therefore a curve that starts at \\(V_{OH}=V_{DD}-V_{TP}\\) for \\(V_{in}<V_{Tn}\\), then decreases linearly with slope \\(-\\sqrt{k_n/k_p}\\) in the saturation region, and finally falls to \\(V_{OL}\\) as \\(V_{in}\\) approaches \\(V_{DD}\\).",
        "format": "markdown",
        "sha256": "34c795fc462b90056d60c9bfd7bf317894788c70bb98ba3d8ae9aadc3206f976"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain \u0002-gm1/gm2\u0002 (equivalently the square-law ratio). The additional VTC discussion does not undermine the essential answer.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 27834,
        "total_tokens": 28079,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26488,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 245,
        "output_tokens": 27834,
        "total_tokens": 28079,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26488,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the arrow shown is the source arrow for an enhancement **p-channel MOSFET**, the circuit is a two-transistor PMOS stage: an inverting common-source amplifier/ratioed inverter with a diode-connected active load.\n\n- \\(M_2\\): PMOS driver  \n  - Source at \\(V_{DD}\\)\n  - Gate at \\(V_{\\rm in}\\)\n  - Drain at \\(V_{\\rm out}\\)\n\n- \\(M_1\\): PMOS active load  \n  - Source at \\(V_{\\rm out}\\)\n  - Gate and drain tied to ground  \n  - Therefore \\(M_1\\) is diode-connected and is always in saturation when it is on.\n\n### Large-signal operation\nFor a PMOS,\n\\[\n\\text{on when } V_{SG}>|V_T|.\n\\]\n\n- \\(M_2\\) is on when\n  \\[\n  V_{DD}-V_{\\rm in}>|V_{T2}|.\n  \\]\n- \\(M_1\\) is on when\n  \\[\n  V_{\\rm out}>|V_{T1}|.\n  \\]\n\nIf both are on and \\(M_2\\) is in saturation,\n\\[\nI_{D2}=\\frac{\\beta_2}{2}\\bigl(V_{DD}-V_{\\rm in}-|V_{T2}|\\bigr)^2,\n\\]\n\\[\nI_{D1}=\\frac{\\beta_1}{2}\\bigl(V_{\\rm out}-|V_{T1}|\\bigr)^2,\n\\]\nwhere\n\\[\n\\beta_i=\\mu_p C_{\\rm ox}\\left(\\frac{W}{L}\\right)_i.\n\\]\nAt the output node, \\(I_{D2}=I_{D1}\\), so\n\\[\n\\boxed{\nV_{\\rm out}\n=\n|V_{T1}|\n+\n\\sqrt{\\frac{\\beta_2}{\\beta_1}}\n\\left(\nV_{DD}-V_{\\rm in}-|V_{T2}|\n\\right)\n}\n\\]\nvalid while \\(M_2\\) remains saturated:\n\\[\nV_{\\rm out}\\le V_{\\rm in}+|V_{T2}|.\n\\]\nIf \\(V_{\\rm in}\\) is too high, \\(M_2\\) turns off and \\(M_1\\) discharges the output until\n\\[\nV_{\\rm out}\\approx |V_{T1}|,\n\\]\nso the low level is not exactly \\(0\\). If \\(V_{\\rm in}\\) is low, \\(M_2\\) pulls the output high; the high level depends on the \\(W/L\\) ratio and is not necessarily rail-to-rail.\n\nThus the stage is inverting:\n\\[\n\\boxed{V_{\\rm out}\\approx \\overline{V_{\\rm in}}\\ \\text{when used as logic}}\n\\]\nbut it is ratioed logic: it draws static current when the output is high/transitioning, unlike a complementary CMOS inverter.\n\n### Small-signal behavior\nFor analog operation, bias \\(V_{\\rm in}\\) near the switching/transition region. Ignoring channel-length modulation,\n\\[\n\\boxed{\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx\n-\\frac{g_{m2}}{g_{m1}}\n=\n-\\sqrt{\\frac{\\beta_2}{\\beta_1}}\n}\n\\]\nso the amplifier is inverting. Including channel-length modulation/body effect,\n\\[\n\\boxed{\nA_v\\approx\n-\\frac{g_{m2}}\n{g_{m1}+g_{ds1}+g_{ds2}+g_{mb1}}\n}\n\\]\nwhere the terms in the denominator represent the diode-connected load conductance and the finite output conductances.\n\nThe small-signal output resistance is correspondingly low:\n\\[\nR_{\\rm out}\\approx\n\\frac{1}{g_{m1}+g_{ds1}+g_{ds2}+g_{mb1}}.\n\\]\nIncreasing \\((W/L)_2\\) relative to \\((W/L)_1\\) increases gain magnitude, but also changes the switching threshold and the output high level.\n\nThe switching threshold, for \\(V_{\\rm in}=V_{\\rm out}=V_M\\) in the saturation region, is approximately\n\\[\n\\boxed{\nV_M=\n\\frac{|V_{T1}|+\\sqrt{\\beta_2/\\beta_1}\\,(V_{DD}-|V_{T2}|)}\n{1+\\sqrt{\\beta_2/\\beta_1}}\n}\n\\]\nequal to about \\(V_{DD}/2\\) for equal devices and thresholds.\n\n**Summary:** the circuit is an inverting PMOS common-source amplifier with a diode-connected PMOS load. It can be used as a ratioed PMOS inverter or, when biased near its transition point, as an inverting analog amplifier. Its output levels are not rail-to-rail, and it is not a low-power complementary CMOS inverter.\n\n*If your symbol convention uses the arrow to denote n-channel depletion-mode devices, then the same topology instead behaves as a source follower with a grounded-gate current-source load: non-inverting, gain slightly less than one, with a dc level shift.*",
        "format": "markdown",
        "sha256": "c81e9c345b83819407c7fde7763aec98e5a0f41c0a783113f843c8b5722b2d9b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Identifies both devices as PMOS, M2 as the common-source input device, and M1 as a diode-connected PMOS load tied to ground; it gives the correct small-signal gain, approximately −gm2/gm1. The speculative alternate symbol-convention note does not displace the correct main analysis.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 37446,
        "total_tokens": 38312,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36384,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 37446,
        "total_tokens": 38312,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36384,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the symbols are standard enhancement p-channel MOSFETs, the circuit is a **pMOS common-source amplifier with a diode-connected pMOS active load**. If it is driven rail-to-rail, it behaves as a **ratioed pMOS inverter**.\n\nLet  \n\\[\nV_t=|V_{TP}|>0,\\qquad \n\\beta_i=\\mu_p C_{ox}(W/L)_i .\n\\]\n\n### 1. Device roles and bias\n- \\(M_2\\): source at \\(V_{DD}\\), drain at \\(V_{OUT}\\), gate at \\(V_{IN}\\). It is the input/common-source device.\n- \\(M_1\\): source at \\(V_{OUT}\\), drain and gate at ground. It is **diode-connected** and therefore acts as a saturated active load, not as an ideal current source.\n\nFor \\(M_1\\),\n\\[\nV_{SG1}=V_{OUT},\\qquad V_{SD1}=V_{OUT}.\n\\]\nWhenever \\(V_{OUT}>V_t\\), it is on, and because \\(V_{SD1}=V_{SG1}>V_{SG1}-V_t\\), it remains in saturation. Thus\n\\[\nI_1=\\frac{\\beta_1}{2}(V_{OUT}-V_t)^2\n\\]\n(neglecting channel-length modulation and body effect for the DC estimate).\n\nFor \\(M_2\\),\n\\[\nV_{SG2}=V_{DD}-V_{IN},\\qquad V_{SD2}=V_{DD}-V_{OUT}.\n\\]\nIt is on when\n\\[\nV_{IN}<V_{DD}-V_t.\n\\]\nIt is in saturation when\n\\[\nV_{OUT}<V_{IN}+V_t,\n\\]\nand then\n\\[\nI_2=\\frac{\\beta_2}{2}(V_{DD}-V_{IN}-V_t)^2.\n\\]\n\n### 2. DC transfer in the active region\nEquating \\(I_1=I_2\\) in saturation gives\n\\[\n\\boxed{\nV_{OUT}=V_t+\n\\sqrt{\\frac{\\beta_2}{\\beta_1}}\\,\n\\bigl(V_{DD}-V_{IN}-V_t\\bigr)\n}\n\\]\n(with \\(\\lambda=0\\)). This is an inverting characteristic: increasing \\(V_{IN}\\) decreases \\(V_{OUT}\\).\n\n- If \\(V_{IN}\\) is too low, \\(M_2\\) enters the triode region; this occurs when\n\\[\nV_{OUT}>V_{IN}+V_t.\n\\]\nThe output then approaches the high rail; the exact high level follows from the triode/saturation current balance.\n- If \\(V_{IN}\\ge V_{DD}-V_t\\), \\(M_2\\) is cut off. The output can only be pulled down by \\(M_1\\) until \\(M_1\\) turns off near \\(V_{OUT}\\approx V_t\\) in the ideal square-law model. In a real circuit, leakage eventually changes this.\n\n### 3. Small-signal behavior\nAt the chosen bias point, let\n\\[\ng_{m2}=\\beta_2(V_{DD}-V_{IN}-V_t),\\qquad\ng_{m1}=\\beta_1(V_{OUT}-V_t),\n\\]\nand\n\\[\nr_{oi}=\\frac{1}{\\lambda_i I_D}.\n\\]\nIf body effect is included for \\(M_1\\), add \\(g_{mb1}\\).\n\nThe output resistance is\n\\[\n\\boxed{\nR_o=\nr_{o1}\\parallel r_{o2}\\parallel\n\\frac{1}{g_{m1}+g_{mb1}}\n}\n\\]\nor, ignoring body effect and using conductances,\n\\[\nR_o\\approx\n\\frac{1}{g_{m1}+g_{o1}+g_{o2}}.\n\\]\n\nThe small-signal voltage gain is\n\\[\n\\boxed{\nA_v=\\frac{v_{out}}{v_{in}}\n=-g_{m2}R_o\n}\n\\]\nso the stage is inverting (\\(180^\\circ\\) phase shift).\n\nIf the output conductances are small and the diode-connected load dominates,\n\\[\n\\boxed{\nA_v\\approx -\\frac{g_{m2}}{g_{m1}}\n= -\\sqrt{\\frac{\\beta_2}{\\beta_1}}\n}\n\\]\nand, if \\(\\mu_pC_{ox}\\) is the same for both devices,\n\\[\n\\boxed{\n|A_v|\\approx\n\\sqrt{\\frac{(W/L)_2}{(W/L)_1}} .\n}\n\\]\nThus the driver \\(M_2\\) should be wider/stronger than the load \\(M_1\\) if gain or a strong high level is required.\n\nThe low-frequency input resistance is essentially infinite because the input is a MOS gate. The output resistance is approximately \\(1/g_{m1}\\) when the diode-connected load is dominant.\n\n### 4. Digital/inverter behavior\nWhen used as a ratioed inverter:\n- \\(V_{IN}\\) high: \\(M_2\\) off; \\(M_1\\) pulls the output low until approximately \\(V_t\\) (ideal enhancement-load model; leakage/loading can change this).\n- \\(V_{IN}\\) low: \\(M_2\\) pulls the output high, while \\(M_1\\) is on, so static current flows. The high output is degraded unless \\(M_2\\) is much stronger than \\(M_1\\).\n\nThe switching threshold, obtained by setting \\(V_{IN}=V_{OUT}=V_M\\) with both devices saturated, is\n\\[\n\\boxed{\nV_M=\n\\frac{s\\,V_{DD}+(1-s)V_t}{1+s},\n\\qquad\ns=\\sqrt{\\frac{\\beta_2}{\\beta_1}}.\n}\n\\]\nFor symmetric devices, \\(\\beta_1=\\beta_2\\), \\(V_M=V_{DD}/2\\).\n\nIn summary, the circuit is an **inverting active-load common-source amplifier** (and a ratioed pMOS inverter when used digitally), with gain approximately\n\\[\n\\boxed{\nA_v\\approx\n-g_{m2}\\left(r_{o2}\\parallel r_{o1}\\parallel \\frac{1}{g_{m1}}\\right)\n}\n\\]\nand, for an ideal square-law diode load with negligible output conductance,\n\\[\n\\boxed{\nA_v\\approx\n-\\sqrt{\\frac{\\beta_2}{\\beta_1}}.\n}\n\\]\nBecause the load is diode-connected, the gain is relatively limited compared with a true current-source load; replacing \\(M_1\\) with a properly biased current source would greatly increase the output resistance and voltage gain.",
        "format": "markdown",
        "sha256": "74a5847ecc15a08db3403b7b97b372ba05396b699362a3ecb8ef413c633beca1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, M2 as the common-source input device, and M1 as a diode-connected PMOS load with gate and drain at ground. It gives the required gm/gm gain, Av ≈ −gm2/gm1, and its additional circuit analysis is consistent with that interpretation.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 38045,
        "total_tokens": 38911,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36665,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 38045,
        "total_tokens": 38911,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36665,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "As drawn, the circuit is a two-MOSFET series stage between \\(V_{DD}\\) and ground, with the output taken at the common node between the two devices.\n\n### Connections\n- \\(M_2\\): gate driven by \\(V_{in}\\); one terminal connected to \\(V_{DD}\\); the other to \\(V_{out}\\).\n- \\(M_1\\): connected between \\(V_{out}\\) and ground; its gate is returned to ground.\n- The output is at the common drain/source node.\n\nBecause the lower gate is grounded, this is **not an ordinary CMOS inverter**. For a normal CMOS inverter, both gates would be driven by \\(V_{in}\\). If \\(M_1\\) is an enhancement-mode NMOS, grounding its gate simply turns it off; the circuit only makes sense if \\(M_1\\) is a depletion-mode NMOS (or is given a separate bias), acting as a current-source load.\n\n## Usual analog interpretation: source follower with active current-source load\nAssuming \\(M_2\\) is an n-channel MOSFET and \\(M_1\\) is a depletion-mode NMOS current sink, the stage is a **common-drain source follower**:\n\n\\[\nV_{out}\\approx V_{in}-V_{GS2}\n\\]\n\nThe lower transistor \\(M_1\\), with \\(V_{GS1}=0\\), sets a nearly constant bias current\n\n\\[\nI_Q=I_{D1}\\approx \\frac12 K_1(-V_{t1})^2\n\\]\n\nwhere \\(K_1=\\mu_nC_{ox}(W/L)_1\\) and \\(V_{t1}<0\\) for a depletion device (or use \\(I_Q=I_{DSS}\\) in a simpler model).\n\nFor \\(M_2\\) in saturation,\n\n\\[\nI_Q=\\frac12 K_2\\left(V_{in}-V_{out}-V_{t2}\\right)^2\n\\]\n\nso\n\n\\[\nV_{out}=V_{in}-V_{t2}-\\sqrt{\\frac{2I_Q}{K_2}}\n\\]\n\nBody effect increases \\(V_{t2}\\) and reduces \\(V_{out}\\).\n\n### Small-signal behavior\nThe output follows the input without inversion. Its voltage gain is slightly less than one:\n\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n=\n\\frac{g_{m2}}\n{g_{m2}+g_{mb2}+1/r_{o2}+1/R_L}\n\\approx \\frac{g_{m2}}{g_{m2}+g_{mb2}+1/R_L}\n\\]\n\nwhere \\(R_L\\) is dominated by the current-source output resistance \\(r_{o1}\\). With ideal current source and no body effect, \\(A_v\\to 1\\).\n\nOther properties:\n- High input resistance.\n- Low output resistance:\n  \\[\n  R_{out}\\approx \\frac{1}{g_{m2}+g_{mb2}}\\parallel r_{o2}\\parallel r_{o1}\n  \\approx \\frac1{g_{m2}}\n  \\]\n- Non-inverting voltage buffer / level shifter.\n- Output high level is degraded by \\(V_{GS2}\\), and output swing is limited by the voltage headroom required to keep \\(M_1\\) acting as a current source.\n\nIf \\(V_{in}\\) is too low, \\(M_2\\) cuts off and \\(M_1\\) pulls the output low. If \\(V_{in}\\) is increased, the output rises, but it cannot exceed approximately \\(V_{DD}-V_{GS2}\\).\n\n## Important note\nIf the intended circuit is the standard **CMOS inverter**, then the lower gate must be connected to \\(V_{in}\\), not ground. In that case:\n- \\(M_2\\) is a PMOS and \\(M_1\\) is an NMOS.\n- \\(V_{in}\\) low \\(\\Rightarrow\\) PMOS ON, NMOS OFF \\(\\Rightarrow V_{out}\\approx V_{DD}\\).\n- \\(V_{in}\\) high \\(\\Rightarrow\\) PMOS OFF, NMOS ON \\(\\Rightarrow V_{out}\\approx 0\\).\n- It is an inverting logic gate; static power is very small, and current flows mainly during switching.\n\nSo the circuit as actually drawn is best described as an **active-loaded MOSFET stage**, most likely a **source follower with a depletion-mode current-source load**, rather than a conventional CMOS inverter.",
        "format": "markdown",
        "sha256": "0b6996b89451501bab49d7c65d8175b19e4ef1238ec9e45d60af97a370d0e22b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the devices as NMOS and the stage as a source follower. Both devices are PMOS: M2 is a common-source input device and M1 is a diode-connected PMOS load, giving approximately Av = -gm2/gm1. The proposed positive-gain follower analysis contradicts the circuit’s essential operation.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 34230,
        "total_tokens": 35096,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33322,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 866,
        "output_tokens": 34230,
        "total_tokens": 35096,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33322,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For the cascode current source shown, the output is taken at the drain of the lower transistor \\(M_1\\). In the small-signal model, \\(V_{DD}\\), \\(V_{b1}\\), and \\(V_{b2}\\) are ac ground, so \\(M_2\\) behaves as \\(r_{o2}\\), and \\(M_1\\) is a common-gate device with source degeneration.\n\nNeglecting body effect:\n\n\\[\n\\boxed{R_{\\rm out}=r_{o1}+r_{o2}+g_{m1}r_{o1}r_{o2}}\n\\]\n\nSince usually \\(g_{m1}r_{o1}\\gg 1\\),\n\n\\[\n\\boxed{R_{\\rm out}\\approx g_{m1}r_{o1}r_{o2}}\n\\]\n\nIf body effect of \\(M_1\\) is included, replace \\(g_{m1}\\) by \\(g_{m1}+g_{mb1}\\):\n\n\\[\n\\boxed{R_{\\rm out}=r_{o1}+r_{o2}+(g_{m1}+g_{mb1})r_{o1}r_{o2}\n\\approx (g_{m1}+g_{mb1})r_{o1}r_{o2}}\n\\]\n\nwhere \\(r_{o1},r_{o2}\\) are the output resistances of \\(M_1,M_2\\), and \\(g_{m1}\\) is the transconductance of the lower transistor \\(M_1\\). If the bulk is tied to the source, set \\(g_{mb1}=0\\).",
        "format": "markdown",
        "sha256": "876f725ce2466d4351f2be2aab6e06d1bae32ad6fe493c5a6f143cff690602bb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate cascode device and gives the correct output-resistance expression and approximation; body effect is handled appropriately.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 13927,
        "total_tokens": 14964,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13601,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 13927,
        "total_tokens": 14964,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13601,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For low-frequency small-signal analysis, \\(V_{DD}\\) and the bias voltages are ac grounds. The top transistor \\(M_2\\) presents \\(r_{o2}\\) at node \\(X\\), and \\(M_1\\) is degenerated by that resistance. Hence\n\n\\[\n\\boxed{R_{\\rm out}\n= r_{o1}+r_{o2}+(g_{m1}+g_{mb1})r_{o1}r_{o2}\n\\approx (g_{m1}+g_{mb1})r_{o1}r_{o2}}\n\\]\n\nIf body effect is neglected, set \\(g_{mb1}=0\\):\n\n\\[\n\\boxed{R_{\\rm out}\\approx g_{m1}r_{o1}r_{o2}\n= (g_{m1}r_{o1})r_{o2}}\n\\]\n\nsince usually \\(g_m r_o\\gg 1\\). Here \\(M_1\\) is the lower transistor (nearest \\(R_{\\rm out}\\)); if your notation numbers the cascode device as \\(M_2\\), interchange the subscripts \\(1\\leftrightarrow2\\).",
        "format": "markdown",
        "sha256": "4400be7a456e7459f91b5ca05adf215be79f83e5d9a6efe0b12199999cc12250"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Gives the correct output-resistance expression with M1 as the output-side device and the correct gm1 cascode factor. The notation caveat does not change the result for the figure.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 16965,
        "total_tokens": 18002,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16731,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 16965,
        "total_tokens": 18002,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16731,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For the PMOS cascode current source shown, with all bias sources ac-grounded, the small-signal output resistance looking into the lower transistor’s drain is\n\n\\[\nR_{\\rm out}=r_{o1}+\\left(1+g_{m1}r_{o1}\\right)r_{o2}\n\\]\n\nor equivalently,\n\n\\[\n\\boxed{R_{\\rm out}=r_{o1}+r_{o2}+g_{m1}r_{o1}r_{o2}}\n\\]\n\nwhere \\(M_1\\) is the lower PMOS whose drain is the output, and\n\n\\[\nr_{o1}=\\frac{1}{\\lambda_1 I_D},\\qquad\nr_{o2}=\\frac{1}{\\lambda_2 I_D}.\n\\]\n\nSince usually \\(g_m r_o \\gg 1\\),\n\n\\[\n\\boxed{R_{\\rm out}\\approx g_{m1}r_{o1}r_{o2}}.\n\\]\n\nIf body effect of \\(M_1\\) is included, replace \\(g_{m1}\\) by \\((g_{m1}+g_{mb1})\\):\n\n\\[\nR_{\\rm out}=r_{o1}+r_{o2}+(g_{m1}+g_{mb1})r_{o1}r_{o2}\n\\;\\approx\\;(g_{m1}+g_{mb1})r_{o1}r_{o2}.\n\\]\n\nSo the cascode gives an output resistance roughly \\(g_m r_o\\) times larger than a single transistor’s \\(r_o\\).",
        "format": "markdown",
        "sha256": "3faabfbf044c0cde4e717ce16c17f8b453fa03fd7888d2a4e9036471da64ed28"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS cascode with M1 as the output-side cascode device and gives the expected Rout expression and approximation; body effect is handled appropriately.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1038,
        "output_tokens": 12858,
        "total_tokens": 13896,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12538,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1038,
        "output_tokens": 12858,
        "total_tokens": 13896,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12538,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the two devices are PMOS transistors (as drawn with \\(V_{DD}\\) at the top):\n\nFor \\(M_2\\),  \n\\[\nV_{SG2}=V_{DD}-V_{b2},\\qquad\nV_{SD2}=V_{DD}-V_X .\n\\]\nSaturation requires\n\\[\nV_{SD2} \\ge V_{SG2}-|V_{Tp}|.\n\\]\nSubstituting,\n\\[\nV_{DD}-V_X \\ge V_{DD}-V_{b2}-|V_{Tp}|\n\\]\nor\n\\[\n\\boxed{V_X \\le V_{b2}+|V_{Tp}|.}\n\\]\nAt equality \\(M_2\\) is at the edge of saturation, so in design leave some margin:\n\\[\nV_X < V_{b2}+|V_{Tp}|.\n\\]\n\nNode \\(X\\) is set by the lower/cascode device \\(M_1\\). If \\(M_1\\) is in saturation,\n\\[\nV_X \\approx V_{b1}+|V_{Tp}|+V_{ov1}.\n\\]\nTherefore, ignoring body effect, \\(M_2\\) remains saturated if\n\\[\nV_{b1}+V_{ov1} \\le V_{b2}\n\\]\nor approximately\n\\[\n\\boxed{V_{b1} < V_{b2}-V_{ov1}.}\n\\]\nSo for the PMOS circuit, choose \\(V_{b2}\\) sufficiently higher than \\(V_{b1}\\) so that the intermediate node \\(X\\) is not pushed too close to \\(V_{DD}\\). Also keep the output voltage low enough that \\(M_1\\) stays saturated:\n\\[\nV_{\\text{out}} \\le V_{b1}+|V_{Tp}|.\n\\]\n\nIn practice, satisfy these inequalities with design margin over process, voltage, and temperature, or use a cascode bias/feedback circuit that generates \\(V_{b1}\\) relative to \\(V_{b2}\\) so that \\(V_X\\) stays below the saturation limit. If the transistors were NMOS instead, all inequalities would be reversed.",
        "format": "markdown",
        "sha256": "34718cf9df00868efcf3d78ea159951a1de60cb1ec01b906fb308b995ab007bd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, gives M2’s saturation condition, and relates VX to Vb1 to derive the equivalent bias condition. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1045,
        "output_tokens": 14588,
        "total_tokens": 15633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14139,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1045,
        "output_tokens": 14588,
        "total_tokens": 15633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14139,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the devices in the figure are PMOS, \\(M_2\\) has  \n\\(V_{S2}=V_{DD}\\), \\(V_{G2}=V_{b2}\\), and \\(V_{D2}=V_X\\).\n\nFor a PMOS to be in saturation,\n\\[\n|V_{SG2}|>|V_{THP2}|\n\\]\nand\n\\[\n|V_{SD2}|\\ge |V_{SG2}|-|V_{THP2}| .\n\\]\nUsing the actual node voltages,\n\\[\nV_{SG2}=V_{DD}-V_{b2},\\qquad\nV_{SD2}=V_{DD}-V_X.\n\\]\nTherefore \\(M_2\\) is saturated when\n\\[\n\\boxed{V_{DD}-V_{b2}>|V_{THP2}|}\n\\]\nand\n\\[\n\\boxed{V_{DD}-V_X \\ge V_{DD}-V_{b2}-|V_{THP2}|}\n\\]\nor, more simply,\n\\[\n\\boxed{V_X \\le V_{b2}+|V_{THP2}|}.\n\\]\n\nEquivalently, defining the overdrive\n\\[\nV_{OV2}=V_{SG2}-|V_{THP2}|=V_{DD}-V_{b2}-|V_{THP2}|>0,\n\\]\nyou need\n\\[\n\\boxed{V_{SD2}=V_{DD}-V_X \\ge V_{OV2}}.\n\\]\nAt the edge of saturation, \\(V_X=V_{b2}+|V_{THP2}|\\); in design, leave some margin.\n\nIn the cascode, \\(V_X\\) is set by the lower device \\(M_1\\) and the current level. If \\(M_1\\) is also in saturation,\n\\[\nV_X=V_{b1}+|V_{GS1}|,\n\\]\nso \\(M_2\\) remains saturated provided\n\\[\n\\boxed{V_{b1}+|V_{GS1}| \\le V_{b2}+|V_{THP2}|}\n\\]\nor, for matched thresholds,\n\\[\n\\boxed{V_{b2}-V_{b1}\\gtrsim V_{OV1}}.\n\\]\nSo, in practice: bias \\(V_{b2}\\) high enough (but still \\(V_{b2}<V_{DD}-|V_{THP2}|\\) so \\(M_2\\) is on), and ensure \\(V_X\\) is not too high by keeping \\(M_1\\) properly biased/saturated. The output voltage must also stay within the cascode’s allowed compliance range; otherwise \\(M_1\\) leaves saturation, \\(V_X\\) moves, and \\(M_2\\) can also fall out of saturation.",
        "format": "markdown",
        "sha256": "e08bb4ecbcc763377c2ab2fbe9d4b4cc3456f8c65ed62abbe00fed4fcd0d8636"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, states M2’s saturation condition, and relates VX to Vb1 to derive the required bias condition. The additional design comments do not undermine the essential answer.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1045,
        "output_tokens": 20988,
        "total_tokens": 22033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20401,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1045,
        "output_tokens": 20988,
        "total_tokens": 22033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20401,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To keep \\(M_2\\) in saturation, its drain–source voltage must be at least its overdrive. For the PMOS cascode shown (with \\(V_{DD}\\) at the top), the source of \\(M_2\\) is at \\(V_{DD}\\), its drain is at node \\(X\\), and its gate is at \\(V_{b2}\\). Thus,\n\n\\[\nV_{SD2}=V_{DD}-V_X,\\qquad V_{SG2}=V_{DD}-V_{b2}\n\\]\n\nSaturation requires\n\n\\[\nV_{SD2}\\ge V_{SG2}-|V_{thp}|\n\\]\n\nso\n\n\\[\nV_{DD}-V_X \\ge V_{DD}-V_{b2}-|V_{thp}|\n\\]\n\nwhich simplifies to\n\n\\[\n\\boxed{V_X \\le V_{b2}+|V_{thp}|}\n\\]\n\nor equivalently,\n\n\\[\n\\boxed{V_{b2} \\ge V_X-|V_{thp}|}\n\\]\n\nAlso, \\(M_2\\) must remain on, so \\(V_{b2}<V_{DD}-|V_{thp}|\\).\n\nSince \\(M_1\\) is in saturation, \\(V_X\\) is approximately \\(V_{b1}+|V_{thp}|+V_{ov1}\\). Therefore, to keep \\(M_2\\) in saturation, the bias \\(V_{b2}\\) must be chosen high enough:\n\n\\[\n\\boxed{V_{b2} > V_{b1}+V_{ov1}}\n\\]\n\nwith a small margin, while still satisfying \\(V_{b2}<V_{DD}-|V_{thp}|\\). In practice, choose \\(V_{b2}\\) so that node \\(X\\) remains below \\(V_{b2}+|V_{thp}|\\), and ensure the output voltage is not so high that \\(M_1\\) leaves saturation or \\(M_2\\) enters triode.",
        "format": "markdown",
        "sha256": "6d90a1acbddf4793d244b7cbcdedb34b882c1cf98c8a7a6a1c3a1a6e95d12db7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS saturation condition and relates \\(V_X\\) to \\(V_{b1}\\), yielding the equivalent bias condition \\(V_{b2}-V_{b1}\\gtrsim V_{ov1}\\) for equal thresholds.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 238,
        "output_tokens": 24497,
        "total_tokens": 24735,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24087,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 238,
        "output_tokens": 24497,
        "total_tokens": 24735,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24087,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume the two transistors are enhancement-mode NMOS devices and are biased in saturation. The circuit is an **NMOS cascode amplifier with an ideal current-source load**:\n\n- \\(M_1\\): input/common-source transistor driven by \\(V_{in}\\).\n- \\(M_2\\): common-gate cascode transistor biased by \\(V_{b1}\\).\n- \\(I_1\\): dc bias-current load. For small signals it is an open circuit (infinite impedance) if ideal.\n- \\(V_{out}\\): taken at the drain of \\(M_2\\). The node \\(X\\) is the source of \\(M_2\\) and drain of \\(M_1\\).\n- The stage is inverting: increasing \\(V_{in}\\) tends to increase \\(M_1\\) current, pulling \\(V_{out}\\) down.\n\n### DC operating point\n\nIn steady state, if both devices conduct and are in saturation,\n\\[\nI_{D1}=I_{D2}=I_1 .\n\\]\nIgnoring body effect and channel-length modulation,\n\\[\nI_1=\\frac12\\mu_n C_{ox}\\left(\\frac WL\\right)_1\n(V_{in}-V_{T1})^2 ,\n\\]\n\\[\nI_1=\\frac12\\mu_n C_{ox}\\left(\\frac WL\\right)_2\n(V_{b1}-V_X-V_{T2})^2 .\n\\]\nDefine overdrive voltages\n\\[\nV_{ov1}=V_{in}-V_{T1},\\qquad\nV_{ov2}=V_{b1}-V_X-V_{T2}.\n\\]\nThen approximately\n\\[\nV_X\\simeq V_{b1}-V_{T2}-V_{ov2},\n\\]\nand the saturation requirements are\n\\[\nM_1:\\quad V_X>V_{ov1},\n\\]\n\\[\nM_2:\\quad V_{out}>V_X+V_{ov2}.\n\\]\nThus the cascode requires extra voltage headroom; the minimum possible output voltage for proper saturation is about\n\\[\nV_{out,\\min}\\approx V_{ov1}+V_{ov2}.\n\\]\nA real current-source load also requires headroom near \\(V_{DD}\\).\n\nWith an ideal current source and an ideal saturation model, the dc value of \\(V_{out}\\) is not uniquely fixed: it is a high-impedance node. In practice, finite transistor output resistance, finite current-source output resistance, output load, or feedback fixes the quiescent \\(V_{out}\\). If \\(V_{in}\\) is below threshold, \\(M_1\\) is off and the output is pulled high; if \\(V_{in}\\) overdrives \\(M_1\\), the output falls low.\n\n### Small-signal analysis\n\nLet\n\\[\ng_{mi}=\\sqrt{2\\mu_n C_{ox}(W/L)_i I_1},\n\\qquad\nr_{oi}\\approx \\frac{1}{\\lambda_i I_1},\n\\]\nand include \\(M_2\\) body effect through\n\\[\ng_{mb2}=\\eta g_{m2},\n\\qquad\ng_{m2}^{*}=g_{m2}+g_{mb2}.\n\\]\nIf the body of \\(M_2\\) is tied to its source, simply set \\(g_{mb2}=0\\).\n\nThe output resistance looking into the cascode is\n\\[\nR_{out,cas}\n=\nr_{o1}+r_{o2}+g_{m2}^{*}r_{o1}r_{o2}\n\\]\n\\[\n\\approx g_{m2}^{*}r_{o1}r_{o2},\n\\qquad (g_mr_o\\gg1).\n\\]\nThe effective short-circuit transconductance is\n\\[\nG_m\n=\ng_{m1}\n\\frac{g_{m2}^{*}+1/r_{o2}}\n{g_{m2}^{*}+1/r_{o1}+1/r_{o2}}\n\\approx g_{m1}.\n\\]\nIf the current source has finite small-signal output resistance \\(R_{cs}\\), and a load \\(R_L\\) is connected,\n\\[\nR_{load}=R_{cs}\\parallel R_L,\n\\qquad\nR_{out,total}=R_{out,cas}\\parallel R_{load}.\n\\]\nThe low-frequency voltage gain is\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n=\n-G_m\\,R_{out,total}\n\\approx\n-g_{m1}\\,\\big(R_{out,cas}\\parallel R_{load}\\big).\n\\]\nFor an ideal current-source load and no external load,\n\\[\nA_v\\approx -g_{m1}g_{m2}^{*}r_{o1}r_{o2},\n\\]\nor, retaining the finite-\\(r_o\\) expression more accurately,\n\\[\nA_{v,\\mathrm{open}}\n\\approx\n-g_{m1}r_{o1}\\left(1+g_{m2}^{*}r_{o2}\\right).\n\\]\nWithout the cascode (replace \\(M_2\\) by a wire), the gain would be only approximately\n\\[\nA_v\\approx -g_{m1}r_{o1},\n\\]\nso the cascode increases the voltage gain by roughly the intrinsic gain \\(g_{m2}r_{o2}\\) of \\(M_2\\).\n\nThe gate input resistance is essentially infinite at low frequency:\n\\[\nR_{in}\\approx \\infty.\n\\]\n\n### Role of \\(M_2\\)\n\nThe cascode transistor \\(M_2\\):\n\n- raises the output resistance and therefore the voltage gain;\n- isolates the drain of \\(M_1\\) from the output, reducing Miller multiplication of \\(C_{gd1}\\) and improving high-frequency behavior;\n- adds a non-dominant pole at node \\(X\\), whose impedance is roughly of order \\(1/g_{m2}\\) in typical loaded operation;\n- costs additional voltage headroom and requires an appropriate bias \\(V_{b1}\\).\n\nIn summary, the circuit is a high-gain, inverting, current-source-loaded NMOS cascode amplifier. Its gain is controlled mainly by \\(g_{m1}\\) and the very large cascode output resistance, while \\(M_2\\) acts as a shielding/cascode device that improves gain and input-output isolation at the expense of headroom. Numerical \\(V_{out}\\) or gain values require the transistor parameters \\((W/L,\\lambda,V_T,\\mu_nC_{ox})\\), bias current \\(I_1\\), and bias voltage \\(V_{b1}\\).",
        "format": "markdown",
        "sha256": "6da3e76f00a821c7bf997197b2f4d0eb3aa8bc6aa912ee21db6dc1b5ec584ebd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression. The additional details do not undermine the essential analysis.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 708,
        "output_tokens": 33099,
        "total_tokens": 33807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31751,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 708,
        "output_tokens": 33099,
        "total_tokens": 33807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31751,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure shows a **current-source-loaded NMOS cascode amplifier**: \\(M_1\\) is the input/common-source device, \\(M_2\\) is the cascode/common-gate device, and \\(I_1\\) is the high-impedance load/bias current source. The output is taken at the drain of \\(M_2\\).\n\n### 1. DC/large-signal operation\nIn steady state,\n\\[\nI_{D1}=I_{D2}=I_1.\n\\]\nBoth transistors must be kept in saturation for amplifier operation:\n\\[\nV_{in}>V_{T1},\\qquad V_X \\ge V_{in}-V_{T1},\n\\]\n\\[\nV_{b1}-V_X>V_{T2},\\qquad\nV_{out}\\ge V_{b1}-V_{T2}.\n\\]\nEquivalently, using overdrive voltages,\n\\[\nV_X\\ge V_{OV1},\\qquad V_{out}-V_X\\ge V_{OV2}.\n\\]\nFor maximum output swing, \\(V_{b1}\\) is chosen so that\n\\[\nV_{out,\\min}\\approx V_{OV1}+V_{OV2},\n\\]\nwhile the maximum output is limited by the current-source compliance and supply, approximately \\(V_{DD}-V_{OV,\\text{load}}\\).\n\nIgnoring channel-length modulation:\n\\[\nI_1=\\frac12\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_1\n(V_{in}-V_{T1})^2\n\\]\nand\n\\[\nI_1=\\frac12\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2\n(V_{b1}-V_X-V_{T2})^2.\n\\]\nWith channel-length modulation, the finite \\(r_{o1},r_{o2}\\) also determine the exact quiescent \\(V_{out}\\). The body effect of \\(M_2\\) raises its threshold because its source \\(X\\) is above ground; this must be included in accurate biasing.\n\nIncreasing \\(V_{in}\\) increases the pull-down current of \\(M_1\\), so the output moves lower. Thus the stage is an **inverting amplifier**:\n\\[\nv_{out}\\approx -|A_v|\\,v_{in}.\n\\]\n\n### 2. Small-signal behavior\nLet\n\\[\ng_{m1},\\ r_{o1}\n\\]\nbe the small-signal parameters of \\(M_1\\), and\n\\[\ng_{m2},\\ g_{mb2},\\ r_{o2}\n\\]\nthose of \\(M_2\\), where \\(g_{mb2}=\\eta g_{m2}\\) accounts for the body effect of the cascode transistor. For an ideal current source, \\(I_1\\) is an AC open circuit.\n\nThe output resistance looking into the cascode branch is\n\\[\nR_{out,\\text{casc}}\n\\approx r_{o1}+r_{o2}\n+(g_{m2}+g_{mb2})r_{o1}r_{o2}.\n\\]\nIf the body effect is neglected,\n\\[\nR_{out,\\text{casc}}\n\\approx r_{o1}+r_{o2}+g_{m2}r_{o1}r_{o2}\n\\approx g_{m2}r_{o1}r_{o2}.\n\\]\nIf the current source has finite small-signal output resistance \\(R_I\\), then\n\\[\nR_{out}=R_{out,\\text{casc}}\\parallel R_I.\n\\]\n\nThe low-frequency voltage gain is approximately\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n\\approx -g_{m1}\\,R_{out}\n= -g_{m1}\\left(R_{out,\\text{casc}}\\parallel R_I\\right).\n\\]\nFor an ideal current-source load, \\(R_I\\to\\infty\\), so\n\\[\nA_v\\approx\n-g_{m1}\\left[r_{o1}+r_{o2}\n+(g_{m2}+g_{mb2})r_{o1}r_{o2}\\right]\n\\]\nand, commonly,\n\\[\n|A_v|\\approx g_{m1}g_{m2}r_{o1}r_{o2}\n=(g_{m1}r_{o1})(g_{m2}r_{o2}).\n\\]\nIf the load resistance is much smaller than the cascode output resistance, then\n\\[\nA_v\\approx -g_{m1}R_I,\n\\]\nso the gain is then set mainly by the load, not by the cascode.\n\nThe input resistance at low frequency is essentially infinite,\n\\[\nR_{in}\\approx \\infty,\n\\]\nwhile the output resistance is very high, as above.\n\n### 3. Role of \\(M_2\\)\n\\(M_2\\) is a **cascode/common-gate device**:\n- It passes the current generated by \\(M_1\\) to the output.\n- Its gate \\(V_{b1}\\) is AC ground, so it shields the output from node \\(X\\).\n- It increases the output resistance by roughly the intrinsic gain of \\(M_2\\), approximately \\(g_{m2}r_{o2}\\).\n- This boosts the gain when the load is highly resistive.\n- It also reduces the Miller effect of \\(M_1\\)'s gate–drain capacitance, improving high-frequency response.\n\nThe price is reduced voltage headroom because both \\(M_1\\) and \\(M_2\\) must remain saturated; the minimum output voltage is approximately \\(V_{OV1}+V_{OV2}\\). The body effect of \\(M_2\\) can also limit swing and slightly increase its threshold. At higher frequencies, node \\(X\\) introduces an additional pole, but its impedance is low, roughly \\(1/(g_{m2}+g_{mb2})\\), so it is usually not the dominant pole.\n\nIn short, the circuit is a high-output-impedance, high-gain inverting cascode amplifier. Its numerical gain and bias point cannot be calculated without transistor dimensions, process parameters, bias voltages, and the current-source output resistance.",
        "format": "markdown",
        "sha256": "4820933f6732236313e4e4d1d89618ca3f80b9216236064c98b0721fb3de02b7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent gain expression −gm1Rout (including the ideal-load cascode result).",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 640,
        "input_tokens": 708,
        "output_tokens": 20867,
        "total_tokens": 21575,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19592,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 640,
        "input_tokens": 708,
        "output_tokens": 20867,
        "total_tokens": 21575,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19592,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This is a single-ended **NMOS cascode amplifier** with an ideal current-source load (or the input branch of a telescopic-cascode/OTA).\n\n- \\(M_1\\): input common-source NMOS, gate driven by \\(v_{in}\\), source grounded.\n- \\(M_2\\): cascode/common-gate NMOS, gate held at dc bias \\(V_{b1}\\).\n- \\(I_1\\): dc current-source load; ideally it is an open circuit for small signals.\n- \\(v_{out}\\): taken at the drain of \\(M_2\\), the high-impedance output node.\n\nSince no numerical device data are given, the following is symbolic.\n\n## 1. DC operating point\n\nFor the devices to operate normally as an amplifier, both NMOS transistors must be in saturation. The same dc current flows through the stack:\n\\[\nI_{D1}=I_{D2}=I_1 .\n\\]\nUsing the square-law model (neglecting channel-length modulation for the bias estimate),\n\\[\nI_1=\\frac12 k_{n1}'(V_{in}-V_{Tn1})^2 ,\n\\]\n\\[\nI_1=\\frac12 k_{n2}'\\big[V_{b1}-V_X-V_{Tn2}(V_X)\\big]^2 ,\n\\]\nwhere \\(V_X\\) is the voltage at the source of \\(M_2\\). \\(M_2\\) has a body effect because its source is above ground:\n\\[\nV_{Tn2}=V_{Tn0}+\\gamma\\left(\\sqrt{2\\phi_F+V_X}-\\sqrt{2\\phi_F}\\right).\n\\]\nThe input bias \\(V_{in}\\) and the gate bias \\(V_{b1}\\) are chosen so that this current equals \\(I_1\\).\n\nSaturation requirements:\n\\[\nV_X \\ge V_{in}-V_{Tn1}\\quad (M_1),\n\\]\n\\[\nV_{out}\\ge V_X+\\big(V_{b1}-V_X-V_{Tn2}\\big)\n\\quad\\Longleftrightarrow\\quad\nV_{out}\\ge V_{b1}-V_{Tn2}\\quad (M_2).\n\\]\nThus the lowest usable output voltage is approximately\n\\[\nV_{out,\\min}\\approx V_{ov1}+V_{ov2},\n\\]\nwhere \\(V_{ov}=V_{GS}-V_T\\). If \\(v_{out}\\) falls below this, \\(M_2\\) enters triode; the cascode loses its high output resistance and the gain drops sharply.\n\nWith an ideal current source and a simple square-law model neglecting output resistance, the quiescent value of \\(v_{out}\\) is not well determined; it is only constrained by the saturation/headroom range. In a real circuit, the current source is usually a PMOS current mirror with finite output resistance, or the amplifier is placed in feedback, which sets the dc output voltage.\n\n## 2. Small-signal behavior\n\nAt low frequency, \\(M_1\\) converts the input voltage into a small-signal current:\n\\[\ni_{d1}\\approx g_{m1}v_{in}.\n\\]\n\\(M_2\\) behaves as a common-gate cascode device: it passes this current to the output and greatly increases the output resistance. The output is inverting: increasing \\(v_{in}\\) turns \\(M_1\\) on harder, pulling \\(v_{out}\\) downward.\n\nDefine\n\\[\nR_L=R_{cs}\\parallel R_{\\rm ext},\n\\]\nwhere \\(R_{cs}\\) is the finite small-signal output resistance of the current-source load (infinite for an ideal source) and \\(R_{\\rm ext}\\) is any external load resistance. The small-signal resistance looking down into the cascode output is\n\\[\nR_{out,c}\n= r_{o1}+r_{o2}\n +(g_{m2}+g_{mb2})r_{o1}r_{o2},\n\\]\nwhere \\(g_{mb2}\\) accounts for the body effect of \\(M_2\\). Often \\(g_m r_o\\gg1\\), so\n\\[\nR_{out,c}\\approx (g_{m2}r_{o2})r_{o1}.\n\\]\nThe total output resistance is\n\\[\nR_{out}=R_{out,c}\\parallel R_L.\n\\]\n\nTo first order, the short-circuit transconductance is\n\\[\nG_m\\approx g_{m1},\n\\]\nso the low-frequency voltage gain is\n\\[\n\\boxed{\nA_v=\\frac{v_{out}}{v_{in}}\n\\approx -g_{m1}\\big(R_{out,c}\\parallel R_L\\big)\n}\n\\]\nor, if the current-source load is ideal and no external load is connected,\n\\[\n\\boxed{\nA_v\\approx -g_{m1}R_{out,c}\n\\approx -g_{m1}g_{m2}r_{o1}r_{o2}\n}\n\\]\nneglecting body effect. Including body effect replaces \\(g_{m2}\\) by \\(g_{m2}+g_{mb2}\\) in the output-resistance term. If the load resistance is much smaller than \\(R_{out,c}\\),\n\\[\nA_v\\approx -g_{m1}R_L,\n\\]\nso the cascode gives little extra gain in a very low-impedance load.\n\nA more exact \\(r_o\\)-model expression is\n\\[\nG_m=\ng_{m1}\\frac{g_{m2}+g_{mb2}+1/r_{o2}}\n{g_{m2}+g_{mb2}+1/r_{o2}+1/r_{o1}},\n\\]\n\\[\nA_v=-G_m\\,R_{out},\n\\qquad\nR_{out}=R_{out,c}\\parallel R_L .\n\\]\nFor most hand calculations, \\(G_m\\approx g_{m1}\\) is sufficiently accurate.\n\n## 3. Role of \\(M_2\\)\n\n\\(M_2\\) is the cascode transistor. Its main effects are:\n\n- **Boosts output resistance** by roughly \\(g_{m2}r_{o2}\\), increasing the voltage gain.\n- **Shields \\(M_1\\) from the output**, reducing the Miller effect on \\(C_{gd1}\\) and improving high-frequency behavior/reverse isolation.\n- **Costs voltage headroom**: the cascode requires about one extra overdrive voltage, so the minimum usable \\(v_{out}\\) is higher than for a simple common-source stage.\n- \\(M_2\\)'s body effect increases its threshold and output resistance; it helps gain slightly but reduces available swing. If possible, tying its body to its source removes \\(g_{mb2}\\).\n\n## 4. Main limitations\n\n- The ideal current source is an open circuit for small signals, so the gain is limited by the finite \\(r_{o1},r_{o2}\\) of the MOSFETs. With ideal square-law devices having \\(r_o\\to\\infty\\), the open-loop low-frequency gain becomes infinite/undefined.\n- In a real implementation, the current source is a PMOS current source or current mirror; its finite output resistance \\(R_{cs}\\) appears in parallel with \\(R_{out,c}\\).\n- The output is a very high-impedance node; it must be connected to a high-impedance load, a buffer, or feedback. Driving a low-resistance load reduces the gain approximately to \\(-g_{m1}R_L\\).\n- The output swing is limited approximately to\n\\[\nV_{ov1}+V_{ov2}\\lesssim V_{out}\\lesssim V_{DD}-|V_{ov,\\text{load}}|.\n\\]\n- The circuit is unstable/unbiased if left open-loop with an ideal current source; practical biasing by a current mirror and/or common-mode feedback is required.\n\n**Summary:** The circuit is an inverting high-gain NMOS cascode stage. \\(M_1\\) performs voltage-to-current conversion; \\(M_2\\) increases the output resistance and reduces Miller feedback. Its approximate small-signal gain is\n\\[\nA_v\\approx -g_{m1}\\left[R_L\\parallel\\left(r_{o1}+r_{o2}\n+(g_{m2}+g_{mb2})r_{o1}r_{o2}\\right)\\right],\n\\]\nwhich for an ideal high-impedance load and negligible body effect becomes\n\\[\nA_v\\approx -g_{m1}g_{m2}r_{o1}r_{o2}.\n\\]",
        "format": "markdown",
        "sha256": "18c3c63120b54825bdeb2ca7ce2e972c4d8e10dfb94ed490725e265b53f3ee10"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the required gain expressions for both finite and ideal current-source loading. Extra analysis does not alter the essential answer.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 708,
        "output_tokens": 25655,
        "total_tokens": 26363,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23880,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 708,
        "output_tokens": 25655,
        "total_tokens": 26363,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23880,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes. The circuit is a **cascode structure**.\n\n- **M1** is the input/common-source transistor: its gate is driven by \\(V_{in}\\), its source is grounded, and its drain is connected to the source of M2.\n- **M2** is the cascode/common-gate transistor: its gate is held at the bias voltage \\(V_{b1}\\), and its drain connects to the load resistor \\(R_D\\) and the output \\(V_{out}\\).\n\nThus the two transistors are stacked in series—common-source M1 followed by common-gate M2—which is the standard single-stage cascode amplifier topology. The bias voltage \\(V_{b1}\\) should be a stable DC/AC-ground bias for M2 to act as the cascode device.",
        "format": "markdown",
        "sha256": "2f3bee0dad64915d09ef726666699b0d17e50830ad0ef74262eb9543be46109c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source stage; the golden solution explicitly assigns 0 to answers that call it a cascode.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 1885,
        "total_tokens": 2642,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1814,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 1885,
        "total_tokens": 2642,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1814,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes. The circuit is a **single-ended NMOS cascode amplifier** (with a resistive load \\(R_D\\)):\n\n- \\(M_1\\): input transistor in a **common-source** configuration, with gate driven by \\(V_{\\mathrm{in}}\\).\n- \\(M_2\\): cascode transistor in a **common-gate** configuration, with its gate held at a dc bias \\(V_{b1}\\).\n- \\(M_1\\) drain drives \\(M_2\\) source; output is taken from \\(M_2\\) drain.\n\nSo it is a **cascode** structure, not merely two cascaded common-source stages. If \\(V_{b1}\\) were actually an ac signal input rather than a dc bias, then it would no longer be the conventional cascode configuration.",
        "format": "markdown",
        "sha256": "7e79556070edacb17f39e24fcd0d4841ee71a981c1ab607a2108619a61af5f42"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source input device, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 1535,
        "total_tokens": 2292,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1368,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 1535,
        "total_tokens": 2292,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1368,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes. The circuit is a simple **cascode amplifier** (common-source/common-gate cascode).\n\n- \\(M_1\\) is the input transistor in a common-source connection; its gate is driven by \\(V_{\\rm in}\\), and its source is grounded.\n- \\(M_2\\) is the cascode transistor in a common-gate connection; its gate is held at a DC bias \\(V_{b1}\\), and its source is connected to the drain of \\(M_1\\).\n- The output is taken at the drain of \\(M_2\\), with \\(R_D\\) as the load.\n\nSo topologically, **yes, it is a cascode structure**. For proper operation, \\(V_{b1}\\) must bias both MOSFETs in saturation. This is a basic/telescopic cascode, not a folded cascode.",
        "format": "markdown",
        "sha256": "8bfb1437873622b41261ba48aadcad0451bf3cc56aaf0b0ec1bd5390f03312a8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source input device, so the structure lacks the cascode resistance boost.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 3179,
        "total_tokens": 3936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 757,
        "output_tokens": 3179,
        "total_tokens": 3936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In a cascode the Miller effect is reduced because the high-output-voltage swing is **isolated from the input device’s drain/collector**.\n\nFor a simple common-source/common-emitter stage, the feedback capacitance \\(C_{gd}\\) (or \\(C_{bc}\\)) bridges input and output and sees the full voltage gain:\n\n\\[\nC_{\\rm in}\\approx C_{gs}+C_{gd}(1+|A_v|),\n\\qquad A_v\\approx -g_m R_L,\n\\]\n\nso \\(C_{gd}\\) is multiplied by a large factor.\n\nIn a cascode, the input transistor \\(Q_1\\) feeds a common-gate/common-base transistor \\(Q_2\\) whose gate/base is ac-grounded. The input resistance seen looking into the source/emitter of \\(Q_2\\) is low, approximately\n\n\\[\nR_{\\rm in2}\\approx \\frac{1}{g_{m2}}.\n\\]\n\nThus the voltage gain of \\(Q_1\\) itself is only\n\n\\[\nA_{v1}=\\frac{v_{d1}}{v_{\\rm in}}\n\\approx -g_{m1}(1/g_{m2})\n= -\\frac{g_{m1}}{g_{m2}},\n\\]\n\nwhich is about \\(-1\\) for matched devices. Consequently the Miller multiplication of \\(Q_1\\)’s \\(C_{gd}\\) is only\n\n\\[\nC_{\\rm in}\\approx C_{gs1}+C_{gd1}\\left(1+\\frac{g_{m1}}{g_{m2}}\\right),\n\\]\n\nrather than being multiplied by the full amplifier gain \\(g_m R_L\\).\n\nThe large overall voltage gain appears at the output of \\(Q_2\\), but the ac-grounded gate/base of \\(Q_2\\) shields this output from the input. \\(Q_2\\)’s \\(C_{gd}\\) goes mainly to ac ground and loads the output; it does not provide a large input-to-output feedback path. Therefore the input capacitance is much smaller, the input pole is pushed higher, and reverse coupling is reduced. The Miller effect is decreased—not completely eliminated—and other poles, such as the cascode-node pole, may then limit bandwidth.",
        "format": "markdown",
        "sha256": "a93872f30d76e81536e1fc7340191557e4d40f16cfb76f7c138bd3ad51157213"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance cascode node and the resulting roughly unity-magnitude gain across the input device’s Cgd, so its Miller multiplication is about 2 rather than the full stage gain. The minor omission of body effect in the approximation does not change the conclusion.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 6519,
        "total_tokens": 6562,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5917,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 6519,
        "total_tokens": 6562,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5917,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The Miller effect is reduced in a cascode because the input transistor’s drain is not allowed to swing with the full, high-gain output.\n\nFor a normal common-source stage, the gate–drain capacitance \\(C_{gd}\\) sees the full inverting voltage gain,\n\n\\[\nA_v \\approx -g_m R_L,\n\\]\n\nso the input capacitance is approximately\n\n\\[\nC_{\\rm in}\\approx C_{gs}+C_{gd}(1+|A_v|).\n\\]\n\nThus \\(C_{gd}\\) is Miller-multiplied by a large factor when the load resistance/gain is large.\n\nIn a cascode, a common-gate device is placed between the common-source device and the output. The source of the common-gate device presents a low impedance to the drain of the input device:\n\n\\[\nR_X \\approx \\frac{1}{g_{m2}}\n\\]\n\n(ignoring finite \\(r_o\\)). Therefore the voltage gain from the gate of the input transistor to its own drain/internal node is only\n\n\\[\nA_X \\approx -g_{m1}R_X \\approx -\\frac{g_{m1}}{g_{m2}}.\n\\]\n\nFor matched devices this is about \\(-1\\), not the full cascode gain. Hence the input capacitance is approximately\n\n\\[\nC_{\\rm in,cascode}\n\\approx C_{gs1}+C_{gd1}\\left(1+\\frac{g_{m1}}{g_{m2}}\\right),\n\\]\n\nwhich for \\(g_{m1}\\approx g_{m2}\\) is only about \\(C_{gs1}+2C_{gd1}\\). The large output voltage swing appears at the drain of the upper common-gate transistor, not at the drain of the input transistor. Since the upper transistor’s gate is at ac ground, its \\(C_{gd}\\) is effectively from the output to ground, not a feedback capacitance from output back to the input.\n\nSo the cascode “shields” the input from the high-swing output; the high output resistance and gain are obtained at the output while the input transistor sees only a low-impedance internal node. The Miller effect is therefore much less pronounced, although not entirely eliminated—there is still a modest Miller multiplication and an internal-node pole set mainly by the upper device’s \\(g_m\\) and node capacitance.",
        "format": "markdown",
        "sha256": "1edf2c20fd97b263abc703c025139a9dc2aa529e3201ba06b9a273a6d687362f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance cascode internal node and the resulting modest gain across the input transistor’s Cgd (about −1 for matched devices), distinguishing it from the full output gain. The Miller effect is reduced, not eliminated; the gm2-only approximation is explicitly qualified.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 8045,
        "total_tokens": 8088,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7565,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 8045,
        "total_tokens": 8088,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7565,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The Miller effect comes from a capacitance between the input and output—usually \\(C_{bc}\\) or \\(C_{gd}\\)—that sees the amplifier’s voltage gain. Its effective input capacitance is approximately\n\n\\[\nC_{\\rm in,M}=C(1-A_v),\n\\]\n\nor for a negative gain, \\(C(1+|A_v|)\\).\n\nIn a simple common-emitter/common-source stage, the collector/drain is the high-swing output, so \\(A_v\\approx -g_mR_L\\) and the feedback capacitance is multiplied by a large factor.\n\nIn a cascode, the input device is followed by a common-base/common-gate device:\n\n- The collector/drain of the first device is connected to the emitter/source of the common-base/gate device, which presents a low input impedance, roughly \\(1/g_{m2}\\) or \\(r_{e2}\\).\n- Therefore the voltage gain from the input to that internal collector/drain node is small:\n  \\[\n  A_{v1}=\\frac{v_{c1}}{v_b}\\approx -\\frac{g_{m1}}{g_{m2}}\\approx -1\n  \\]\n  for equal currents.\n- So the Miller multiplication of \\(C_{bc1}\\) or \\(C_{gd1}\\) is only about\n  \\[\n  C_{\\mu1}\\left(1+\\frac{g_{m1}}{g_{m2}}\\right),\n  \\]\n  roughly \\(2C_{\\mu1}\\) in a typical matched cascode, instead of \\(C_{\\mu1}(1+g_mR_L)\\).\n\nThe full output voltage swing does occur at the collector/drain of the upper device, but its base/gate is AC grounded. Its collector-base/gate capacitance therefore goes mainly from the output to AC ground, not back to the overall input, so it does not produce input Miller capacitance.\n\nThus the cascode “shields” the input device from the high output voltage swing, giving much lower input capacitance, higher input impedance, wider bandwidth, and better reverse isolation. The effect is reduced, not perfectly eliminated; finite upper-device input impedance, device output capacitance, and nonideal grounds leave some residual feedback.",
        "format": "markdown",
        "sha256": "e6c34701e5b146bf51e98fd4a046bfe53e1d2ccefcea43ef2c05240575568981"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance cascode node and shows that the gain across the input device’s Cgd is about −1, so its Miller multiplication is roughly 2 rather than the full stage-gain factor. The effect is accurately described as reduced, not eliminated.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 6851,
        "total_tokens": 6894,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6401,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 43,
        "output_tokens": 6851,
        "total_tokens": 6894,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6401,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the symbols are the usual ones—\\(M_1\\) is a pMOS transistor and \\(M_2\\) is an nMOS transistor, with \\(V_{\\rm in}\\) driving the source of \\(M_2\\) and \\(V_{b1}\\) biasing its gate—the circuit is:\n\n\\[\n\\boxed{\\text{An nMOS common-gate stage loaded by a pMOS current-source active load.}}\n\\]\n\nThe output node \\(V_{\\rm out}\\) is the common drain node of \\(M_1\\) and \\(M_2\\), and it is a high-impedance node.\n\n### 1. DC bias / operating region\n\nLet the DC current through the stack be \\(I_B\\). Then\n\n\\[\nI_{D1}=I_{D2}=I_B.\n\\]\n\nFor \\(M_1\\) (pMOS current source) to be in saturation,\n\n\\[\nV_{DD}-V_{b2}>|V_{TP}|,\n\\qquad\nV_{out}\\le V_{b2}+|V_{TP}|.\n\\]\n\nIts bias current, ignoring channel-length modulation for the moment, is\n\n\\[\nI_B \\approx\n\\frac{1}{2}\\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_1\n\\left(V_{DD}-V_{b2}-|V_{TP}|\\right)^2.\n\\]\n\nFor \\(M_2\\) (nMOS common-gate) to conduct and remain in saturation,\n\n\\[\nV_{b1}-V_{in}>V_{TN},\n\\qquad\nV_{out}\\ge V_{b1}-V_{TN},\n\\]\n\nwhere \\(V_{TN}\\) may include body effect if the bulk is not tied to the source. The current is\n\n\\[\nI_B \\approx\n\\frac{1}{2}\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2\n\\left(V_{b1}-V_{in}-V_{TN}\\right)^2.\n\\]\n\nThus, for both transistors to remain in saturation,\n\n\\[\n\\boxed{\nV_{b1}-V_{TN}\\lesssim V_{out}\\lesssim V_{b2}+|V_{TP}|\n}\n\\]\n\nwith the exact equality set by the current balance, including finite output resistances/channel-length modulation. With ideal current sources and no channel-length modulation, the output dc voltage is not well defined because it is a floating high-impedance node; in practice, \\(r_{o1}\\), \\(r_{o2}\\), mismatch, or feedback set it.\n\n### 2. Small-signal behavior\n\nReplace the biased \\(M_1\\) by its output resistance \\(r_{o1}\\), and use the small-signal model of \\(M_2\\) with transconductance \\(g_{m2}\\), body-effect transconductance \\(g_{mb2}\\), and output resistance \\(r_{o2}\\). Define\n\n\\[\ng_m' = g_{m2}+g_{mb2}\n\\]\n\n(use only \\(g_{m2}\\) if the bulk is tied to the source or body effect is neglected).\n\n#### Voltage gain\n\n\\[\n\\boxed{\nA_v=\\frac{v_{out}}{v_{in}}\n\\approx\ng_m'(r_{o1}\\parallel r_{o2})\n}\n\\]\n\nMore exactly,\n\n\\[\n\\boxed{\n\\frac{v_{out}}{v_{in}}\n=\n\\frac{g_m'+\\frac{1}{r_{o2}}}\n     {\\frac{1}{r_{o1}}+\\frac{1}{r_{o2}}}\n}\n\\]\n\nThe gain is positive (non-inverting): increasing \\(V_{in}\\) decreases the \\(V_{GS}\\) of \\(M_2\\), reducing its current, so the current-source load charges the output node upward.\n\n#### Input resistance\n\n\\[\n\\boxed{\nR_{in}\\approx \\frac{1}{g_{m2}+g_{mb2}}\n}\n\\]\n\nIf the finite output resistances are included,\n\n\\[\n\\boxed{\nR_{in}=\n\\frac{r_{o1}+r_{o2}}\n     {1+(g_{m2}+g_{mb2})r_{o2}}\n}\n\\]\n\nThus the common-gate input has a low input impedance.\n\n#### Output resistance\n\nWith an ideal zero-resistance input voltage source, set \\(v_{in}=0\\) for small-signal purposes:\n\n\\[\n\\boxed{\nR_{out}\\approx r_{o1}\\parallel r_{o2}\n}\n\\]\n\nIf the input source has finite resistance \\(R_s\\),\n\n\\[\n\\boxed{\nR_{out}=\nr_{o1}\\parallel\n\\left[\nr_{o2}\\bigl(1+(g_{m2}+g_{mb2})R_s\\bigr)+R_s\n\\right].\n}\n\\]\n\n### 3. Qualitative operation\n\n- \\(M_1\\) acts as a current-source load; \\(V_{b2}\\) sets the bias current.\n- \\(M_2\\) is a common-gate transistor: it converts variations of the source voltage \\(V_{in}\\) into drain-current variations.\n- The stage has:\n  - large non-inverting voltage gain,\n  - low input resistance \\(\\approx 1/g_m\\),\n  - high output resistance,\n  - output swing limited by both transistors staying in saturation.\n- If the input source cannot sink dc current, an ac-coupling/bias network is needed because the dc bias current flows through the source terminal of \\(M_2\\).\n\nIf an external load \\(R_L\\) is connected from \\(V_{out}\\) to ac ground, replace \\(r_{o1}\\) in the small-signal formulas by \\(r_{o1}\\parallel R_L\\).\n\n> If your symbol convention instead has \\(V_{in}\\) applied to the gate of \\(M_2\\) with \\(V_{b1}\\) as its source bias, then the stage is a common-source amplifier rather than common-gate. In that case, approximately  \n> \\[\n> A_v\\approx -g_{m2}(r_{o1}\\parallel r_{o2}),\\qquad\n> R_{in}\\approx \\infty,\\qquad\n> R_{out}\\approx r_{o1}\\parallel r_{o2},\n> \\]\n> i.e., an inverting high-gain stage with a pMOS current-source load.",
        "format": "markdown",
        "sha256": "48ee91148adaf8abcebbf420ae9af66abc16af7ef3c8fcdecaf8bf09787cf766"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS with a PMOS current-source load, places Vin at M2’s source and the bias voltages appropriately, and gives the non-inverting gain and low input resistance. Its gain expression is equivalent to the golden expression; the additional details do not contradict the essential analysis.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 650,
        "output_tokens": 29234,
        "total_tokens": 29884,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 650,
        "output_tokens": 29234,
        "total_tokens": 29884,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27926,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure is a CMOS active-loaded amplifier. Under the usual reading of the symbols:\n\n- \\(M_1\\): pMOS transistor with source at \\(V_{DD}\\), gate biased at \\(V_{b2}\\); it behaves as a current-source load.\n- \\(M_2\\): nMOS transistor with gate biased at \\(V_{b1}\\), source driven by \\(V_{in}\\), and drain at \\(V_{out}\\).  \n  Thus \\(M_2\\) is connected as a **common-gate amplifier**, loaded by the pMOS current source.\n\n## 1. DC bias / operating conditions\n\nFor \\(M_1\\), with ideal channel-length modulation ignored for the moment,\n\\[\nV_{SG1}=V_{DD}-V_{b2},\\qquad\nV_{ov1}=V_{SG1}-|V_{tp}|.\n\\]\nFor \\(M_1\\) to be on and in saturation,\n\\[\nV_{b2}<V_{DD}-|V_{tp}|,\n\\]\nand\n\\[\nV_{out}<V_{b2}+|V_{tp}|.\n\\]\nIts current is\n\\[\nI_{D1}=\\frac12 \\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_1\n\\left(V_{DD}-V_{b2}-|V_{tp}|\\right)^2\n\\left[1+\\lambda_p(V_{DD}-V_{out})\\right].\n\\]\n\nFor \\(M_2\\),\n\\[\nV_{GS2}=V_{b1}-V_{in},\\qquad\nV_{ov2}=V_{b1}-V_{in}-V_{tn}.\n\\]\nFor \\(M_2\\) to be on and in saturation,\n\\[\nV_{in}<V_{b1}-V_{tn},\n\\]\nand\n\\[\nV_{out}>V_{b1}-V_{tn}\n\\]\n(equivalently \\(V_{DS2}=V_{out}-V_{in}>V_{ov2}\\)).\nIts current is approximately\n\\[\nI_{D2}=\\frac12 \\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2\n\\left(V_{b1}-V_{in}-V_{tn}\\right)^2\n\\left[1+\\lambda_n(V_{out}-V_{in})\\right].\n\\]\nIf the body of \\(M_2\\) is tied to ground rather than to its source, the body effect changes \\(V_{tn}\\) and adds a small-signal \\(g_{mb}\\).\n\nIn steady state, ignoring any external load,\n\\[\nI_{D1}=I_{D2}.\n\\]\nIncluding finite output resistances, this determines the quiescent output voltage \\(V_{out}\\). The useful output range is approximately\n\\[\nV_{b1}-V_{tn}<V_{out}<V_{b2}+|V_{tp}|,\n\\]\nso both transistors remain in saturation.\n\n## 2. Small-signal behavior\n\nDefine\n\\[\ng_{m2}=\\sqrt{2\\mu_n C_{ox}(W/L)_2 I_D},\n\\qquad\nr_{o1}\\approx \\frac{1}{\\lambda_p I_D},\n\\qquad\nr_{o2}\\approx \\frac{1}{\\lambda_n I_D}.\n\\]\nIf a load resistance \\(R_L\\) is connected at \\(V_{out}\\), the output resistance is\n\\[\nR_{out}=r_{o1}\\parallel r_{o2}\\parallel R_L.\n\\]\nFor no external load, omit \\(R_L\\).\n\nThe common-gate voltage gain is non-inverting:\n\\[\n\\frac{v_{out}}{v_{in}}\n\\approx\n(g_{m2}+g_{mb2})\\,R_{out},\n\\]\nor, neglecting body effect,\n\\[\n\\boxed{\\frac{v_{out}}{v_{in}}\\approx g_{m2}\\left(r_{o1}\\parallel r_{o2}\\parallel R_L\\right)}\n\\]\nwith a positive sign. A more exact expression, including the finite \\(r_{o2}\\) feedback term, is\n\\[\nA_v=\n\\frac{(g_{m2}+g_{mb2})+1/r_{o2}}\n{1/r_{o2}+1/(r_{o1}\\parallel R_L)}.\n\\]\nThe input resistance looking into the source of \\(M_2\\) is low:\n\\[\nR_{in}\\approx \\frac{1}{g_{m2}+g_{mb2}}\n\\]\nor about \\(1/g_{m2}\\) if body effect is neglected. The output resistance is high, set by \\(r_{o1}\\parallel r_{o2}\\).\n\n## 3. Operation summary\n\n- \\(M_1\\) supplies a nearly constant bias current and provides a large output resistance.\n- \\(M_2\\) converts the input voltage at its source into a drain current; this current flows through the high output resistance, producing a voltage at \\(V_{out}\\).\n- The stage is a **common-gate amplifier / current buffer**: low input impedance, high output impedance, non-inverting voltage gain. It is often used in low-noise amplifiers, cascode stages, and current-sensing circuits.\n\nIf the drawing convention in your course instead takes \\(V_{in}\\) as the gate of \\(M_2\\) and \\(V_{b1}\\) as its source bias, then the circuit is a **common-source amplifier**; the same output-resistance calculation applies, but the gain is inverted:\n\\[\nA_v\\approx -g_{m2}\\left(r_{o1}\\parallel r_{o2}\\parallel R_L\\right),\n\\]\nand the input resistance is ideally very high at low frequency.",
        "format": "markdown",
        "sha256": "b252947a42ba0c3a07b302b9fdf71ecfd8f999ea45e78580bdbb36dad38536df"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS with PMOS current-source load, places Vin at M2’s source, and gives the non-inverting gain and low input resistance. The optional detailed formulas do not contradict the essential answer.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 650,
        "output_tokens": 31417,
        "total_tokens": 32067,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 650,
        "output_tokens": 31417,
        "total_tokens": 32067,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30240,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a **single-stage CMOS amplifier** with a **PMOS current-source load** and an **NMOS driving transistor** (a current-source-loaded inverter / common-source amplifier).\n\n### 1. Device roles\n- **M1 (PMOS):** connected between \\(V_{DD}\\) and \\(V_{out}\\), gate biased by \\(V_{b2}\\). It acts as a **current source**.\n- **M2 (NMOS):** connected between \\(V_{out}\\) and \\(V_{b1}\\), gate driven by \\(V_{in}\\). It acts as the **common-source driver**.\n- The output \\(V_{out}\\) is the common drain node of the two transistors.\n\n### 2. DC bias\nIn steady state, the currents through M1 and M2 must be equal:\n\\[\nI_{D1}=I_{D2}=I_D\n\\]\nIf both are in saturation, the square-law equations are:\n\\[\nI_{D1}=\\frac12 \\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_1\n\\left(V_{DD}-V_{b2}-|V_{thp}|\\right)^2\n\\left(1+\\lambda_p(V_{DD}-V_{out})\\right)\n\\]\n\\[\nI_{D2}=\\frac12 \\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_2\n\\left(V_{in}-V_{b1}-V_{thn}\\right)^2\n\\left(1+\\lambda_n(V_{out}-V_{b1})\\right)\n\\]\nSolving these gives the bias/output voltage \\(V_{out}\\).\n\nSaturation conditions:\n\\[\n\\text{M1: } V_{out}\\le V_{b2}+|V_{thp}|\n\\]\n\\[\n\\text{M2: } V_{out}\\ge V_{in}-V_{thn}\n\\]\nAlso, for proper operation:\n\\[\nV_{b1}<V_{out}<V_{DD}\n\\]\n\n### 3. Transfer characteristic\nThe circuit is an **inverting amplifier**:\n- When \\(V_{in}\\) is low, M2 is off, so M1 pulls \\(V_{out}\\) high (\\(\\approx V_{DD}\\)).\n- When \\(V_{in}\\) is high, M2 conducts and pulls \\(V_{out}\\) low (\\(\\approx V_{b1}+I_D R_{on2}\\)).\n- The switching threshold is where the currents are equal:\n\\[\nV_{in,th}=V_{b1}+V_{thn}\n+\\sqrt{\\frac{\\mu_p(W/L)_1}{\\mu_n(W/L)_2}}\n\\left(V_{DD}-V_{b2}-|V_{thp}|\\right)\n\\]\nThe output is a **high-gain inverter** with a transition region around \\(V_{in,th}\\).\n\n### 4. Small-signal analysis\nAssume both transistors are in saturation. The small-signal gain is:\n\\[\nA_v=-g_{m2}(r_{o1}\\parallel r_{o2})\n\\]\nwhere\n\\[\ng_{m2}=\\sqrt{2\\mu_n C_{ox}(W/L)_2 I_D}\n=\\frac{2I_D}{V_{in}-V_{b1}-V_{thn}}\n\\]\n\\[\nr_{o1}=\\frac{1}{\\lambda_p I_D},\\qquad\nr_{o2}=\\frac{1}{\\lambda_n I_D}\n\\]\nThe input resistance is:\n\\[\nR_{in}=\\infty\n\\]\nThe output resistance is:\n\\[\nR_{out}=r_{o1}\\parallel r_{o2}\n\\]\nThe gain is negative and high because the output is a high-impedance node.\n\n### 5. Summary\nThe circuit is a **PMOS current-source-loaded NMOS common-source amplifier**:\n- High voltage gain, inverting output.\n- High output impedance, so the output is sensitive to load.\n- Static current flows when the output is low, so it dissipates static power.\n- \\(V_{b1}\\) and \\(V_{b2}\\) adjust the operating point and output swing.\n- The output swing is approximately from \\(V_{b1}\\) to \\(V_{DD}\\), with a transition at \\(V_{in,th}\\).",
        "format": "markdown",
        "sha256": "dc1805145eafb9930e6746c57a6e09f0cb8a90124f14eeb81d3848cf3f24251c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2's gate and identifies the circuit as a common-source inverter. The golden solution specifies Vin at M2's source in a common-gate stage; this topology error directly triggers the stated zero-credit rule.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 27819,
        "total_tokens": 28052,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 27819,
        "total_tokens": 28052,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26931,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **2 poles**:\n\n1. At the input/gate node of \\(M_1\\) (set by \\(R_S\\), \\(C_{GS}\\), and the coupling through \\(C_{GD}\\)).\n2. At the output node \\(V_{\\text{out}}\\) (loaded by \\(C_{DB}\\), \\(C_{GD2}\\), \\(C_{DB2}\\), etc.).\n\nThe ac-grounded bias/supply terminals of \\(M_2\\) do not create additional independent nodes; \\(C_{GD}\\) couples the two nodes but does not add a third pole.",
        "format": "markdown",
        "sha256": "b71c15438501dc21909dadc84d634f20bb6f74d21330039b5175423999a51381"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two poles at the M1 gate and output nodes, assigns the relevant capacitances to those nodes, and notes that CGD couples the nodes without adding a third pole.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 23051,
        "total_tokens": 23986,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22933,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 23051,
        "total_tokens": 23986,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22933,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **2 poles**.\n\nIn the small-signal ac equivalent, there are only two independent capacitive nodes:\n\n1. The input gate node of \\(M_1\\) — \\(C_{GS}\\) to ground, with \\(C_{GD}\\) coupling it to the output.\n2. The output node (drain of \\(M_1\\)/drain of \\(M_2\\)) — \\(C_{DB}\\), \\(C_{GD2}\\), and \\(C_{DB2}\\) are effectively in parallel to ac ground.\n\nThe gate, source, and body of \\(M_2\\) are at ac ground, so they do not create additional independent nodes. The transfer function is therefore second-order, i.e. **two poles**.  \nIf ideal infinite output resistance is assumed, one of these poles is at the origin; with the usual finite transistor output resistance, both are finite.",
        "format": "markdown",
        "sha256": "d80513f4924b9e8d87cb530842f83e0071caa418c82bb1c7338728f984c29c40"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the two capacitive nodes and assigns the relevant capacitances to them; the M1 gate-output coupling does not add a pole. The output-resistance qualification is also consistent with the idealized limit.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 28099,
        "total_tokens": 29034,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27920,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 28099,
        "total_tokens": 29034,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27920,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit has **2 poles**.\n\nIn the small-signal model, there are only two independent capacitive nodes that can create poles:\n\n1. **Input node** at the gate of \\(M_1\\): includes \\(C_{GS}\\) and the Miller-coupled \\(C_{GD}\\).\n2. **Output node** at the common drain: includes \\(C_{DB}\\), \\(C_{GD2}\\), \\(C_{DB2}\\), and the other end of \\(C_{GD}\\).\n\nThe gate and supply of \\(M_2\\) are ac grounds, so \\(C_{GD2}\\) and \\(C_{DB2}\\) simply add capacitance from output to ground and do not create additional poles.\n\n\\[\n\\boxed{\\text{2 poles}}\n\\]\n\nThe feedthrough capacitor \\(C_{GD}\\) can also introduce a zero, but it does not increase the pole count beyond the two independent capacitive nodes.",
        "format": "markdown",
        "sha256": "bb2024a9d27322b4f20acba5dfd5bc1f959ea63b50e7401565769180317d4761"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies two independent capacitive nodes, assigns the output capacitances appropriately, and notes that the coupling capacitor can add a zero without creating another pole.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 15299,
        "total_tokens": 16234,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15117,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 935,
        "output_tokens": 15299,
        "total_tokens": 16234,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15117,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume the two symbols are enhancement-mode \\(n\\)-channel MOSFETs, with the body effect neglected unless stated otherwise. The circuit is a **resistor-loaded NMOS inverter realized with a two-transistor series pull-down stack**. Since both gates are tied to \\(V_{\\rm in}\\), it is also the pull-down network of a two-input NAND with its inputs tied together.\n\n### Basic operation\n- \\(V_{\\rm in}\\) low: both \\(M_1\\) and \\(M_2\\) are off. No current flows through \\(R_D\\), so\n  \\[\n  V_{\\rm out}\\approx V_{DD}.\n  \\]\n- \\(V_{\\rm in}\\) high: both \\(M_1\\) and \\(M_2\\) turn on, pulling \\(V_{\\rm out}\\) low. Because the two devices are in series and \\(R_D\\) is a passive pull-up, \\(V_{\\rm out}\\) is set by a resistive divider, so it is **not exactly 0 V**.\n- Therefore the logic function is inversion:\n  \\[\n  V_{\\rm out}=\\overline{V_{\\rm in}}\n  \\]\n  for valid logic levels. If the gates were separate inputs \\(A,B\\), the same structure would implement a 2-input NAND: output low only when both inputs are high.\n\n### Approximate \\(V-I/V_{\\rm out}\\) relations\nLet\n\\[\n\\beta=\\mu_n C_{ox}\\frac{W}{L}, \\qquad V_T=\\text{NMOS threshold}.\n\\]\nFor a conducting stack, KCL at the output is\n\\[\nI_D=\\frac{V_{DD}-V_{\\rm out}}{R_D}.\n\\]\n\nFor \\(V_{\\rm in}>V_T\\) while \\(V_{\\rm out}\\) is still high enough that \\(M_2\\) is saturated and \\(M_1\\) is in triode (equal devices, body effect ignored),\n\\[\nV_X=\\left(1-\\frac1{\\sqrt2}\\right)(V_{\\rm in}-V_T),\n\\]\n\\[\nI_D\\approx \\frac{\\beta}{4}(V_{\\rm in}-V_T)^2,\n\\]\nand\n\\[\nV_{\\rm out}=V_{DD}-I_D R_D.\n\\]\nThus the series stack gives roughly half the current of a single saturated NMOS with the same overdrive.\n\nThe switching point \\(V_M\\) where \\(V_{\\rm out}=V_{\\rm in}\\) approximately satisfies\n\\[\n\\frac{V_{DD}-V_M}{R_D}\n\\approx\n\\frac{\\beta}{4}(V_M-V_T)^2.\n\\]\n\nFor a large high input, both transistors are in their triode region, and a rough low-output estimate is\n\\[\nV_{OL}\\approx\n\\frac{V_{DD}}\n{1+\\frac{\\beta R_D}{2}(V_{\\rm in,H}-V_T)} .\n\\]\nHence \\(R_D\\) must be sufficiently large relative to the effective ON resistance of the stack; otherwise the output-low level is too high and the circuit does not provide a valid logic zero.\n\n### Important second-order effects\n- \\(M_2\\) has a nonzero source voltage \\(V_X\\). In a common-substrate process its source-body voltage is positive, so its threshold increases:\n  \\[\n  V_{T2}=V_{T0}+\\gamma\\left(\\sqrt{2\\phi_F+V_X}-\\sqrt{2\\phi_F}\\right).\n  \\]\n  This reduces the pull-down current, raises the switching threshold, and increases delay.\n- The stack has a “stacking” effect: it conducts less current than a single NMOS of the same size and therefore is slower or requires larger \\(W/L\\). It also reduces subthreshold leakage.\n- Unlike a CMOS inverter, there is a static current path from \\(V_{DD}\\) to ground when \\(V_{\\rm in}\\) is high:\n  \\[\n  P_{dc}\\approx V_{DD}I_D\n  =V_{DD}\\frac{V_{DD}-V_{OL}}{R_D}.\n  \\]\n- The output high is close to \\(V_{DD}\\), but the output low is ratio-dependent and nonzero.\n\n### Small-signal viewpoint\nIf biased so that \\(M_2\\) is saturated and \\(M_1\\) is in triode, the series pair behaves like a composite transistor. For equal devices and ignoring channel-length modulation/body effect, its effective transconductance is about\n\\[\ng_{m,\\rm eff}\\approx \\frac{\\beta}{2}(V_{\\rm in}-V_T),\n\\]\nso the low-frequency gain is approximately\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\n\\approx -g_{m,\\rm eff}\\,R_D\n\\]\n(modified by the finite output resistance of \\(M_2\\) if channel-length modulation is included). With a constant bias on the upper gate, this structure would be a cascode; with the gate tied to \\(V_{\\rm in}\\), it is a self-cascode-like stack and is not a true cascode.\n\nNumerical values for \\(V_{OH},V_{OL},V_M\\), gain, and delay require \\(V_{DD}\\), \\(R_D\\), \\(V_T\\), \\(\\beta\\), and the body-effect/process parameters.",
        "format": "markdown",
        "sha256": "136329d7df30c5d806058573929384f1d3a0f3a2f03f92917242970fe67ce366"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The operating analysis is largely sound: it identifies the common-gated stack, the lower device in triode and upper device in saturation under the stated bias, and derives the reduced current and transconductance. However, it does not clearly state the key conclusion that the pair behaves approximately like one NMOS with effective channel length L1 + L2.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 28653,
        "total_tokens": 29414,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27565,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 28653,
        "total_tokens": 29414,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27565,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the schematic provided, here is a detailed analysis of the circuit.\n\n### 1. Circuit Identification\nThis circuit is a **Cascode Amplifier** (specifically, a stacked MOSFET amplifier with a common input). It consists of two N-channel enhancement-mode MOSFETs (\\(M_1\\) and \\(M_2\\)) connected in series. \n\nUnlike a traditional cascode where the upper transistor's gate is held at a fixed DC bias voltage, here **both gates are tied to the same input voltage (\\(V_{in}\\))**. \n\n### 2. Components and Configuration\n*   **\\(M_1\\) (Bottom Transistor):** Operates primarily as a **Common-Source (CS)** amplifier. Its source is grounded.\n*   **\\(M_2\\) (Top Transistor):** Acts as the cascode device. Because its gate is connected to the input rather than a fixed AC ground, it acts as a signal-following current buffer.\n*   **\\(R_D\\):** The drain load resistor.\n*   **\\(V_{DD}\\):** The positive DC supply voltage.\n*   **\\(V_{in}\\):** The input signal (which contains both the DC bias and the AC signal).\n*   **\\(V_{out}\\):** The output voltage, taken at the drain of \\(M_2\\).\n\n### 3. DC (Bias) Analysis\nFor the circuit to operate as an amplifier, both transistors must ideally be in the **saturation region**. \n*   The current flowing through the branch is \\(I_D = I_{D1} = I_{D2}\\).\n*   \\(V_{GS1} = V_{in} - 0 = V_{in}\\)\n*   \\(V_{GS2} = V_{in} - V_{D1}\\) (where \\(V_{D1}\\) is the voltage at the node between the two transistors).\n\n**Biasing Challenge:** Because both gates share the same voltage, ensuring both transistors remain in saturation is difficult. \n*   For \\(M_1\\) to be saturated: \\(V_{D1} > V_{in} - V_{th}\\).\n*   For \\(M_2\\) to conduct: \\(V_{GS2} > V_{th} \\Rightarrow V_{in} - V_{D1} > V_{th} \\Rightarrow V_{D1} < V_{in} - V_{th}\\).\n*   These inequalities contradict each other. In practice, to keep \\(M_1\\) saturated, \\(M_2\\) is often forced into the triode region, or the dimensions of the transistors (\\(W/L\\)) must be carefully ratioed. For small-signal AC analysis, we typically assume an ideal operating point where both are in saturation.\n\n### 4. AC (Small-Signal) Analysis\nWhen a small AC signal \\(v_{in}\\) is applied on top of the DC bias:\n*   \\(M_1\\) converts the input voltage into a small-signal current: \\(i_{d1} = g_{m1} v_{in}\\).\n*   \\(M_2\\) transfers this current to the output. Because its gate is driven by \\(v_{in}\\) at the same time as \\(M_1\\), the voltage at the intermediate node (drain of \\(M_1\\)) remains nearly constant. This is known as a **virtual AC ground** at that node.\n\n**Key Small-Signal Parameters:**\n*   **Transconductance (\\(G_m\\)):** The overall transconductance is approximately equal to that of the bottom transistor: \n    \\[\nG_m \\approx g_{m1}\n\\]\n*   **Output Resistance (\\(R_{out}\\)):** The cascode configuration significantly boosts the output resistance looking into the drain of \\(M_2\\):\n    \\[\nR_{out} \\approx g_{m2} \\cdot r_{o1} \\cdot r_{o2}\n\\]\n    *(where \\(r_{o1}\\) and \\(r_{o2}\\) are the output resistances of the individual transistors).*\n*   **Voltage Gain (\\(A_v\\)):** The gain is the transconductance multiplied by the total impedance at the output (the parallel combination of \\(R_D\\) and \\(R_{out}\\)):\n    \\[\nA_v = -G_m (R_D \\parallel R_{out}) \\approx -g_{m1} R_D\n\\]\n    *(Note: If \\(R_D\\) is much smaller than \\(R_{out}\\), the gain is similar to a single-transistor amplifier. The true benefit of this cascode is seen when \\(R_D\\) is replaced by a high-impedance active current source).*\n\n### 5. Advantages and Disadvantages\n**Advantages:**\n*   **High Output Impedance:** Provides a much higher output resistance than a single MOSFET.\n*   **Simplified Biasing:** Eliminates the need for a separate DC bias generation circuit for the cascode transistor (since it uses \\(V_{in}\\)).\n*   **Reduced Miller Effect for \\(M_1\\):** Because the intermediate node acts as a virtual AC ground, the gate-drain capacitance of \\(M_1\\) is not multiplied by the full voltage gain, improving the frequency response.\n\n**Disadvantages:**\n*   **High Input Capacitance:** The gate-drain capacitance of \\(M_2\\) is connected between the input and the highly amplified output, causing a severe **Miller effect** that dominates the input capacitance and can limit high-frequency performance.\n*   **Reduced Voltage Headroom:** Stacking two transistors requires a higher \\(V_{DD}\\) to keep both functional.\n*   **Difficult DC Biasing:** As noted, keeping both identical transistors saturated with a common gate voltage is inherently problematic.",
        "format": "markdown",
        "sha256": "5de93d0f0b07f2fd39cbc7079967e26d71298782f32dd320c845587deafda68c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misclassifies the circuit as a true cascode, assigns the devices incorrect operating regions, and uses a cascode output-resistance formula. It misses the essential result: the lower device operates in triode and extends the upper device’s channel, so the pair behaves approximately like one NMOS with effective channel length L1 + L2.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 12879,
        "total_tokens": 13640,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11680,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 12879,
        "total_tokens": 13640,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11680,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the two symbols are enhancement-mode n-channel MOSFETs, with the lower device \\(M_1\\) driven by \\(V_{\\rm in}\\), the upper device \\(M_2\\) in series, and \\(R_D\\) as the pull-up resistor, the circuit is a resistor-loaded NMOS inverter (or, if the two gates are separate inputs, an NMOS NAND gate). Let \\(V_X\\) be the node between \\(M_2\\) and \\(M_1\\), and define\n\\[\nK=\\mu_n C_{\\rm ox}\\frac{W}{L},\\qquad I_D^{\\rm sat}=\\frac{K}{2}(V_{GS}-V_T)^2,\n\\]\n\\[\nI_D^{\\rm tri}=K\\left[(V_{GS}-V_T)V_{DS}-\\frac{V_{DS}^2}{2}\\right].\n\\]\nNeglect for the moment channel-length modulation and body effect.\n\n### DC equations\nFor \\(M_1\\):\n\\[\nV_{GS1}=V_{\\rm in},\\qquad V_{DS1}=V_X.\n\\]\nFor \\(M_2\\):\n\\[\nV_{GS2}=V_{G2}-V_X,\\qquad V_{DS2}=V_{\\rm out}-V_X,\n\\]\nwhere \\(V_{G2}\\) is the actual gate voltage of \\(M_2\\). The same current flows through both devices and through \\(R_D\\):\n\\[\nI_D(M_1)=I_D(M_2)=\\frac{V_{DD}-V_{\\rm out}}{R_D}.\n\\]\nSolving these equations, with the proper cutoff/saturation/triode condition for each transistor, gives the operating point and the voltage-transfer characteristic.\n\n### If \\(M_2\\)'s gate is tied to \\(V_{\\rm in}\\) as drawn\nThen, for identical devices,\n\\[\nV_{\\rm in}<V_T:\\quad \\text{both transistors off},\\quad I_D=0,\\quad V_{\\rm out}=V_{DD}.\n\\]\nAs \\(V_{\\rm in}\\) rises above \\(V_T\\), the stack conducts. In the first part of the characteristic \\(M_2\\) is saturated and \\(M_1\\) is in triode. Let\n\\[\na=V_{\\rm in}-V_T.\n\\]\nThen\n\\[\nI_D=\\frac{K}{4}a^2,\n\\qquad\nV_X=a\\left(1-\\frac{1}{\\sqrt2}\\right),\n\\]\nand\n\\[\n\\boxed{V_{\\rm out}=V_{DD}-\\frac{K R_D}{4}(V_{\\rm in}-V_T)^2}\n\\]\nas long as\n\\[\nV_{\\rm out}\\ge V_{\\rm in}-V_T.\n\\]\nThis condition ends at\n\\[\nV_{\\rm inA}=V_T+\n\\frac{2}{K R_D}\\left(\\sqrt{1+K R_D V_{DD}}-1\\right).\n\\]\nFor \\(V_{\\rm in}>V_{\\rm inA}\\), \\(M_2\\) enters triode; both upper and lower transistors are then in the ohmic region for most of the low-output part. The output is the smaller root of\n\\[\nV_{\\rm out}^2-\\left(2a+\\frac{4}{K R_D}\\right)V_{\\rm out}\n+\\frac{4V_{DD}}{K R_D}=0,\n\\]\ni.e.\n\\[\n\\boxed{\nV_{\\rm out}\n=a+\\frac{2}{K R_D}\n-\\sqrt{\\left(a+\\frac{2}{K R_D}\\right)^2\n-\\frac{4V_{DD}}{K R_D}}\n}\n\\]\nwhen this root is below \\(V_{\\rm in}-V_T\\).\n\nAt very large \\(V_{\\rm in}\\), a useful approximation is\n\\[\nV_{\\rm out}\\approx\n\\frac{V_{DD}}{1+\\frac{K R_D}{2}(V_{\\rm in}-V_T)} ,\n\\]\nso for a good low level one needs large \\(W/L\\) or a sufficiently large \\(R_D\\).\n\nThe switching threshold \\(V_M\\) (where \\(V_{\\rm out}=V_{\\rm in}\\)) is\n\\[\n\\boxed{\nV_M=V_T+\n\\frac{2}{K R_D}\n\\left[\n\\sqrt{1+K R_D(V_{DD}-V_T)}-1\n\\right].\n}\n\\]\nTypical output levels are\n\\[\nV_{OH}\\approx V_{DD},\\qquad\nV_{OL}\\ll V_{DD}\\quad\\text{if }K R_D(V_{DD}-V_T)\\gg1.\n\\]\n\n### Logic operation\n- Low \\(V_{\\rm in}\\): \\(M_1\\) and \\(M_2\\) are off; the resistor pulls \\(V_{\\rm out}\\) high.  \n- High \\(V_{\\rm in}\\): both series transistors conduct, pulling \\(V_{\\rm out}\\) low.  \nThus the circuit behaves as an inverter.\n\nIf the two gates are instead two independent logic inputs \\(A\\) and \\(B\\), then the output is low only when both inputs are high, so the circuit is a resistor-loaded NMOS NAND gate:\n\\[\nV_{\\rm out}\\text{ high unless }A=B=1,\\qquad\nY=\\overline{AB}.\n\\]\n\n### Practical notes\n- In an integrated n-channel process, the upper transistor has its source at a positive potential \\(V_X\\). Its body effect raises its threshold voltage,\n\\[\nV_{T2}=V_{T0}+\\gamma\\left(\\sqrt{2\\phi_F+V_X}-\\sqrt{2\\phi_F}\\right),\n\\]\nso the real current is lower and the real \\(V_{OL}\\) is slightly higher than the simple square-law result.\n- This is ratioed logic: a finite current flows when the pull-down stack is on, so static power is dissipated for the low-output state. The low level is not exactly \\(0\\) unless \\(R_D\\) is very large or the transistor widths are sufficiently large.\n- If in your version of the figure the gate of \\(M_2\\) is not connected to \\(V_{\\rm in}\\) but to a fixed bias, \\(V_{DD}\\), or its own drain, replace \\(V_{G2}\\) above by that actual voltage. For a fixed-bias upper gate the circuit becomes a cascode-type stage: \\(M_1\\) is the input transistor, \\(M_2\\) is an upper cascode/current-passing device, and the output resistance is increased. For a diode-connected \\(M_2\\), set \\(V_{G2}=V_{\\rm out}\\). The same current-balance equations above still apply.",
        "format": "markdown",
        "sha256": "0d4a5faccec57852ac9151a3a0a84809e6e30d4b38f9dbb743faeed3c31076fc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly recognizes the common-gated series NMOS stack and identifies the lower device as triode and the upper device as saturated in the relevant region; much of its inverter analysis is consistent with that topology. However, it misses the essential conclusion that the pair behaves approximately like one NMOS with effective channel length L1 + L2, focusing instead on logic behavior and adding irrelevant alternative-topology discussion.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 48193,
        "total_tokens": 48954,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41948,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 761,
        "output_tokens": 48193,
        "total_tokens": 48954,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41948,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume the MOSFETs are enhancement NMOS devices and are biased in saturation, and that \\(I_1\\) is an ideal dc tail-current sink. The circuit is a **source-coupled NMOS pair** with a single-ended output:\n- \\(M_1\\): input device; its drain is at \\(V_{DD}\\), so it acts as a source follower/common-drain stage driven by \\(V_{in}\\).\n- \\(M_2\\): common-gate device biased by \\(V_b\\); its drain drives the resistive load \\(R_D\\) and produces \\(V_{out}\\).\n- \\(I_1\\) fixes the total source current, \\(I_{D1}+I_{D2}=I_1\\). Rising \\(V_{in}\\) increases \\(I_{D1}\\), decreases \\(I_{D2}\\), and therefore **raises** \\(V_{out}\\). The small-signal gain is non-inverting from \\(V_{in}\\) to \\(V_{out}\\).\n\n## 1. DC / large-signal operation\n\nFor saturation and negligible channel-length modulation,\n\\[\nI_{D1}=\\frac{\\beta_1}{2}(V_{in}-V_S-V_{Tn})^2,\n\\qquad\nI_{D2}=\\frac{\\beta_2}{2}(V_b-V_S-V_{Tn})^2,\n\\]\nwhere\n\\[\nI_{D1}+I_{D2}=I_1,\n\\]\nand\n\\[\nV_{out}=V_{DD}-I_{D2}R_D.\n\\]\nHere \\(V_S\\) is the dc voltage of the common-source node, and\n\\(\\beta_i=\\mu_n C_{ox}(W/L)_i\\).\n\nFor matched devices, \\(\\beta_1=\\beta_2=\\beta\\), with \\(\\Delta=V_{in}-V_b\\):\n\\[\nV_S=\\frac{V_{in}+V_b}{2}-V_{Tn}\n-\\sqrt{\\frac{I_1}{\\beta}-\\frac{\\Delta^2}{4}},\n\\]\n\\[\nI_{D2}=\n\\frac{I_1}{2}\n-\\frac{\\beta\\Delta}{2}\n\\sqrt{\\frac{I_1}{\\beta}-\\frac{\\Delta^2}{4}},\n\\]\nprovided both transistors remain on:\n\\[\n|\\Delta|<\\sqrt{\\frac{2I_1}{\\beta}}.\n\\]\nThen\n\\[\nV_{out}=V_{DD}-I_{D2}R_D.\n\\]\n\nAt the balanced operating point \\(V_{in}=V_b\\),\n\\[\nI_{D1}=I_{D2}=\\frac{I_1}{2},\n\\]\n\\[\nV_{S,Q}=V_b-V_{Tn}-\\sqrt{\\frac{I_1}{\\beta}},\n\\]\n\\[\nV_{out,Q}=V_{DD}-\\frac{I_1R_D}{2}.\n\\]\n\nFor \\(V_{in}\\) far above \\(V_b\\), \\(M_2\\) cuts off and \\(V_{out}\\to V_{DD}\\). For \\(V_{in}\\) far below \\(V_b\\), \\(M_1\\) cuts off, \\(M_2\\) takes all of \\(I_1\\), and the output tends toward \\(V_{DD}-I_1R_D\\), provided \\(M_2\\) remains in saturation/triode is avoided.\n\nUseful saturation conditions:\n\\[\nM_1:\\quad V_{DD} > V_{in}-V_{Tn},\n\\]\nwhich is normally satisfied for \\(V_{in}\\le V_{DD}\\),\n\\[\nM_2:\\quad V_{out} > V_b-V_{Tn}.\n\\]\nThe tail source also needs enough voltage headroom:\n\\[\nV_S > V_{\\text{compliance of }I_1}.\n\\]\n\n## 2. Small-signal voltage gain\n\nDefine\n\\[\ng_{mi}=\\sqrt{2\\beta_i I_{Di}}\n\\]\n(and \\(g_{mi}\\approx 2I_{Di}/V_{ov,i}\\) in strong inversion), with channel-length output resistances \\(r_{oi}\\), and body-effect transconductances \\(g_{mbi}\\) if the bulk is not tied to each source. If body-source are tied, set \\(g_{mbi}=0\\).\n\nNeglecting channel-length modulation, body effect, and finite tail-source resistance, the small-signal equivalent gives\n\\[\nv_s=\\frac{g_{m1}v_{in}}{g_{m1}+g_{m2}},\n\\]\nand the output is produced by the small-signal decrease of \\(I_{D2}\\):\n\\[\nA_v=\\frac{v_{out}}{v_{in}}\n\\approx\n\\frac{g_{m1}g_{m2}}{g_{m1}+g_{m2}}R_D.\n\\]\nFor matched transistors at balance \\(g_{m1}=g_{m2}=g_m\\):\n\\[\n\\boxed{A_v\\approx \\frac{g_mR_D}{2}>0.}\n\\]\nIf the devices are matched and balanced,\n\\[\ng_m=\\sqrt{\\beta I_1},\n\\]\nso\n\\[\n\\boxed{A_v\\approx \\frac{R_D}{2}\\sqrt{\\beta I_1}\n=\\frac{R_D}{2}\\sqrt{\\mu_nC_{ox}(W/L)I_1}.}\n\\]\nAt very small signals around \\(V_{in}=V_b\\), this is the incremental gain. For larger swings the pair is nonlinear and eventually one device cuts off.\n\nIncluding the finite output resistance of a matched pair with ideal tail current source gives the useful approximation\n\\[\nA_v\\cong \\frac{g_m}{2}\\,(R_D\\parallel 2r_o)\n\\]\nwhen \\(r_{o1}=r_{o2}=r_o\\); for \\(R_D\\ll r_o\\), this reduces to \\(g_mR_D/2\\).\n\nIncluding body effect, the simplified gain is\n\\[\nA_v\\approx\n\\frac{g_{m1}(g_{m2}+g_{mb2})R_D}\n{g_{m1}+g_{mb1}+g_{m2}+g_{mb2}}.\n\\]\nIf the body is tied to the source, omit the \\(g_{mb}\\) terms. For a source-coupled pair with matched devices and an ideal tail, the body effect largely cancels in the differential-mode gain.\n\nA compact general small-signal expression including finite \\(r_{oi}\\), body effect, and finite tail resistance \\(R_T\\) of \\(I_1\\) is\n\\[\nA_v=\n\\frac{g_{m1}\\!\\left(g_{m2}+g_{mb2}+\\frac1{r_{o2}}\\right)}\n{\\left(g_{m1}+g_{mb1}+\\frac1{r_{o1}}+\\frac1{R_T}\\right)\n\\left(\\frac1{R_D}+\\frac1{r_{o2}}\\right)\n+\\frac{g_{m2}+g_{mb2}+1/r_{o2}}{R_D}},\n\\]\nwith \\(R_T\\to\\infty\\) for an ideal current source. The sign is positive as drawn: increasing \\(V_{in}\\) raises \\(V_{out}\\).\n\nIf a small signal is applied to \\(V_b\\) while \\(V_{in}\\) is held fixed, the gain to \\(V_{out}\\) is negative (approximately \\(-g_{m1}g_{m2}R_D/(g_{m1}+g_{m2})\\) when secondary effects are small).\n\n## 3. Input and output resistance\n\nAt low frequency the gate input resistance is effectively infinite:\n\\[\nR_{in}\\approx\\infty.\n\\]\n\nThe output resistance looking into the \\(M_2\\) drain without \\(R_D\\) is\n\\[\nR_{out,M2}\n=\nr_{o2}\\left[1+(g_{m2}+g_{mb2})R_s\\right]+R_s,\n\\]\nwhere\n\\[\nR_s=\n\\left(\ng_{m1}+g_{mb1}+\\frac1{r_{o1}}+\\frac1{R_T}\n\\right)^{-1}\n\\]\nis the small-signal resistance from the common-source node to ground (excluding \\(M_2\\)). Including the load resistor,\n\\[\n\\boxed{R_{out}=R_D\\parallel R_{out,M2}.}\n\\]\nFor an ideal tail, no body effect, and matched devices,\n\\[\nR_s\\approx \\frac1{g_m},\\qquad\nR_{out,M2}\\approx 2r_o,\n\\]\nso\n\\[\nR_{out}\\approx R_D\\parallel 2r_o.\n\\]\nIf \\(R_D\\ll r_o\\), the output resistance is approximately just \\(R_D\\).\n\n## Summary\n\n- The circuit is a single-ended-output source-coupled pair/differential amplifier; \\(M_1\\) is driven by \\(V_{in}\\), \\(M_2\\) is biased at \\(V_b\\), and the ideal tail current sets \\(I_{D1}+I_{D2}=I_1\\).\n- Increasing \\(V_{in}\\) increases \\(V_{out}\\); the low-frequency gain is positive.\n- For matched devices and neglecting secondary effects:\n\\[\nA_v\\approx \\frac{g_{m1}g_{m2}}{g_{m1}+g_{m2}}R_D\n\\approx \\frac{g_mR_D}{2}\n=\\frac{R_D}{2}\\sqrt{\\beta I_1}.\n\\]\n- The output dc level is approximately\n\\[\nV_{out,Q}=V_{DD}-\\frac{I_1R_D}{2}\n\\]\nwhen \\(V_{in}=V_b\\) and the devices are matched.\n- Keep both transistors saturated: \\(V_{out}>V_b-V_{Tn}\\) and the tail node above the current-source compliance. Large \\(|V_{in}-V_b|\\) drives one transistor off and makes the transfer characteristic nonlinear/clipped.",
        "format": "markdown",
        "sha256": "922a8714ec16438b9113e6ce464df5ce56b65b30b46e35df22ef8ed80a2faeda"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-coupled pair as a source follower driving a common-gate stage, with the output at M2’s drain, and gives the correct non-inverting gain. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1040,
        "output_tokens": 41711,
        "total_tokens": 42751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 39687,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1040,
        "output_tokens": 41711,
        "total_tokens": 42751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 39687,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume enhancement-mode NMOS transistors \\(M_1,M_2\\), matched, biased in saturation, and neglect channel-length modulation for the large-signal expressions. The circuit is a source-coupled differential pair with only one output taken at the drain of \\(M_2\\). \\(I_1\\) is the tail current source; \\(V_b\\) is the reference/bias input.\n\n### 1. Operation\n- \\(M_1\\) senses \\(V_{\\rm in}\\); its drain is tied to \\(V_{DD}\\), so it acts as a source follower driving the common-source node.\n- \\(M_2\\) is a common-gate stage with fixed gate bias \\(V_b\\). Its drain drives \\(R_D\\), producing \\(V_{\\rm out}\\).\n- The tail current fixes\n  \\[\n  I_{D1}+I_{D2}=I_1.\n  \\]\n- If \\(V_{\\rm in}\\) increases, \\(M_1\\) takes more of the tail current, the common-source node rises, \\(M_2\\)’s \\(V_{GS}\\) decreases, \\(I_{D2}\\) decreases, and therefore\n  \\[\n  V_{\\rm out}=V_{DD}-I_{D2}R_D\n  \\]\n  rises. Thus the output is **non-inverting with respect to \\(V_{\\rm in}\\)** (and inverting with respect to \\(V_b\\)).\n\n### 2. Large-signal/D.C. behavior\nLet\n\\[\n\\beta=\\mu_n C_{ox}\\frac{W}{L}\n\\]\nfor equal devices, and define \\(V_{id}=V_{\\rm in}-V_b\\). Ignoring channel-length modulation,\n\\[\nI_{D1}=\\frac{I_1}{2}\n+\\frac{\\beta}{4}V_{id}\n\\sqrt{\\frac{4I_1}{\\beta}-V_{id}^2},\n\\]\n\\[\nI_{D2}=\\frac{I_1}{2}\n-\\frac{\\beta}{4}V_{id}\n\\sqrt{\\frac{4I_1}{\\beta}-V_{id}^2}.\n\\]\nHence\n\\[\nV_{\\rm out}\n=V_{DD}-I_{D2}R_D.\n\\]\nThese equations are valid while both transistors remain on:\n\\[\n|V_{id}|<\\sqrt{\\frac{2I_1}{\\beta}}.\n\\]\nBeyond that, one transistor cuts off and the output saturates at approximately \\(V_{DD}\\) or \\(V_{DD}-I_1R_D\\).\n\nFor zero differential input, \\(V_{\\rm in}=V_b\\):\n\\[\nI_{D1}=I_{D2}=\\frac{I_1}{2},\n\\]\n\\[\nV_{\\rm out,Q}=V_{DD}-\\frac{I_1R_D}{2},\n\\]\n\\[\nV_S=V_b-V_{TH}-\\sqrt{\\frac{I_1}{\\beta}},\n\\]\nwhere \\(V_S\\) is the common-source voltage. The small-signal transconductance of each transistor at this bias is\n\\[\ng_m=\\sqrt{\\beta I_1}\n\\]\n(assuming equal \\(W/L\\)).\n\nFor saturation:\n\\[\nV_{DD}-V_S>V_{GS1}-V_{TH},\n\\qquad\nV_{\\rm out}-V_S>V_{GS2}-V_{TH}.\n\\]\nIn particular, \\(M_2\\) requires roughly\n\\[\nV_{\\rm out}>V_b-V_{TH}.\n\\]\nThe tail current source also requires enough voltage at the common-source node to remain in saturation.\n\n### 3. Small-signal voltage gain\nFor low frequencies, short circuit the d.c. sources and let \\(v_{\\rm in},v_b,v_{\\rm out}\\) denote small-signal variations. Ignoring \\(r_o\\),\n\\[\nv_{\\rm out}\n=\n\\frac{g_{m1}g_{m2}R_D}{g_{m1}+g_{m2}}\n\\left(v_{\\rm in}-v_b\\right).\n\\]\nTherefore\n\\[\nA_v=\\frac{v_{\\rm out}}{v_{\\rm in}}\\bigg|_{v_b=0}\n=\n\\frac{g_{m1}g_{m2}R_D}{g_{m1}+g_{m2}}.\n\\]\nFor matched transistors, \\(g_{m1}=g_{m2}=g_m\\), so\n\\[\n\\boxed{A_v=+\\frac{g_mR_D}{2}}\n\\]\nwith \\(V_b\\) held constant. Equivalently,\n\\[\n\\boxed{v_{\\rm out}\\approx \\frac{g_mR_D}{2}(v_{\\rm in}-v_b)}\n\\]\nfor small differential input.\n\nIncluding finite channel-length resistance \\(r_o\\), for matched devices,\n\\[\n\\boxed{A_v=\\frac{g_m}{2}\\left(R_D\\parallel 2r_o\\right)}\n\\]\n\\[\n\\approx \\frac{g_mR_D}{2}\n\\quad\\text{if }R_D\\ll r_o.\n\\]\nThe output resistance at the output node is approximately\n\\[\n\\boxed{R_{\\rm out}=R_D\\parallel 2r_o}\n\\]\n(including \\(R_D\\)); without \\(R_D\\), the resistance looking into the drain of \\(M_2\\) is approximately \\(2r_o\\). With ideal transistors, \\(r_o\\to\\infty\\), so \\(R_{\\rm out}\\approx R_D\\).\n\nThe low-frequency input resistance is essentially infinite because it is a MOSFET gate.\n\n### 4. Common-mode behavior\nWith an ideal tail current source, matched devices, and low-frequency analysis, common-mode variations at \\(V_{\\rm in}\\) and \\(V_b\\) are ideally rejected. If the tail current source has finite output resistance \\(R_T\\), the common-mode gain is approximately\n\\[\nA_{cm}\\approx -\\,\\frac{R_D}{2R_T},\n\\]\nso the CMRR is approximately\n\\[\n\\boxed{\\mathrm{CMRR}\\approx g_mR_T}\n\\]\nunder the usual approximation \\(g_mR_T\\gg1\\). A high-impedance tail current source is therefore important for good common-mode rejection.\n\n### Summary\n\\[\n\\boxed{\\text{Single-ended output differential amplifier: }V_{\\rm out}\\propto V_{\\rm in}-V_b}\n\\]\n\\[\n\\boxed{A_v\\approx +\\frac{g_mR_D}{2}\\quad(g_m=\\sqrt{\\beta I_1}\\text{ at balanced bias})}\n\\]\n\\[\n\\boxed{V_{\\rm out,Q}=V_{DD}-\\frac{I_1R_D}{2}}\n\\]\nfor matched devices with \\(V_{\\rm in,Q}=V_b\\). Numerical values require \\(V_{DD},I_1,R_D,W/L,V_{TH},\\) etc.",
        "format": "markdown",
        "sha256": "474a79c68f88e77880a9440297277590a3553d08a0c76674b9b1f2d4de199c93"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-coupled pair as a source follower driving a common-gate stage, and gives the correct non-inverting gain. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1040,
        "output_tokens": 35453,
        "total_tokens": 36493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1040,
        "output_tokens": 35453,
        "total_tokens": 36493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Circuit type:** This is a source-coupled NMOS differential pair with a single-ended output. The ideal tail current \\(I_1\\) is split between \\(M_1\\) and \\(M_2\\). \\(M_1\\)’s drain is tied directly to \\(V_{DD}\\), so only \\(M_2\\)’s drain current flows through \\(R_D\\) and produces \\(V_{\\rm out}\\). The differential input is \\(V_{in}-V_b\\); \\(V_{in}\\) is non-inverting and \\(V_b\\) is inverting to \\(V_{\\rm out}\\).\n\nAssume \\(M_1\\) and \\(M_2\\) are matched, operate in saturation, and channel-length modulation/body effect are neglected unless noted. Let\n\\[\n\\beta=\\mu_n C_{ox}\\frac{W}{L},\\qquad V_{th}=V_{th,n}.\n\\]\n\n### DC operating point\nAt balance \\(V_{in}=V_b\\),\n\\[\nI_{D1}=I_{D2}=\\frac{I_1}{2},\n\\]\n\\[\nV_{ov0}=\\sqrt{\\frac{I_1}{\\beta}},\\qquad\nV_S=V_b-V_{th}-V_{ov0}=V_{in}-V_{th}-V_{ov0},\n\\]\n\\[\nV_{\\rm out,Q}=V_{DD}-\\frac{I_1}{2}R_D.\n\\]\nFor \\(M_2\\) to remain saturated,\n\\[\nV_{\\rm out,Q}\\ge V_b-V_{th}.\n\\]\nFor \\(M_1\\), saturation is normally satisfied if \\(V_{DD}\\ge V_{in}-V_{th}\\).\n\nThe small-signal transconductance at this bias is\n\\[\ng_m=\\sqrt{\\beta I_1}=\\beta V_{ov0}.\n\\]\n\n### Large-signal behavior\nLet \\(V_{id}=V_{in}-V_b\\). While both devices are on and saturated,\n\\[\nI_{D2}\n=\n\\frac{I_1}{2}\n-\\frac{\\beta}{4}V_{id}\n\\sqrt{\\frac{4I_1}{\\beta}-V_{id}^2},\n\\]\nand\n\\[\nV_{\\rm out}=V_{DD}-I_{D2}R_D.\n\\]\nFor \\(V_{id}>\\sqrt{2I_1/\\beta}\\), \\(M_2\\) turns off and \\(V_{\\rm out}\\approx V_{DD}\\). For \\(V_{id}<-\\sqrt{2I_1/\\beta}\\), \\(M_1\\) turns off and \\(I_{D2}\\approx I_1\\), so \\(V_{\\rm out}\\approx V_{DD}-I_1R_D\\) as long as \\(M_2\\) remains saturated.\n\n### Small-signal gain\nThe small-signal drain current in \\(M_2\\) is\n\\[\ni_{d2}=-\\frac{g_m}{2}(v_{in}-v_b).\n\\]\nThus\n\\[\nv_{\\rm out}\\approx \\frac{g_m R_D}{2}(v_{in}-v_b).\n\\]\nIf \\(V_b\\) is a fixed DC bias, the voltage gain from \\(V_{in}\\) to \\(V_{\\rm out}\\) is\n\\[\n\\boxed{A_v=\\frac{g_m R_D}{2}}\n\\]\nand is non-inverting. If \\(V_b\\) is the input while \\(V_{in}\\) is fixed, the gain is \\(-g_mR_D/2\\).\n\nWith channel-length modulation included, the effective output resistance is approximately \\(R_D\\parallel 2r_o\\), so\n\\[\nA_v\\approx \\frac{g_m}{2}\\left(R_D\\parallel 2r_o\\right).\n\\]\n\n### Input/output resistance\n\\[\nR_{\\rm in}\\approx \\infty\n\\]\nat low frequency because the inputs are MOSFET gates. The output resistance is\n\\[\nR_{\\rm out}\\approx R_D\n\\]\nif \\(r_o\\) is neglected, or\n\\[\nR_{\\rm out}\\approx R_D\\parallel 2r_o\n\\]\nwhen \\(r_o\\) is included.\n\n### Common-mode rejection\nWith an ideal tail current source, common-mode input changes do not change the output, so\n\\[\nA_{cm}\\approx 0,\\qquad \\text{CMRR}\\to\\infty.\n\\]\nIf the tail source has finite small-signal resistance \\(r_t\\), then approximately\n\\[\nA_{cm}\\approx -\\frac{g_m R_D}{1+2g_m r_t},\\qquad\n\\text{CMRR}\\approx \\frac{|A_d|}{|A_{cm}|}\\approx g_m r_t.\n\\]\n\n**Summary:** The circuit is a single-ended differential amplifier. For a fixed \\(V_b\\), it converts \\(V_{in}-V_b\\) to a current that steers away from \\(M_2\\), producing an output voltage \\(V_{\\rm out}=V_{DD}-I_{D2}R_D\\). Its nominal small-signal gain is \\(g_mR_D/2\\), it is non-inverting from \\(V_{in}\\), and it rejects common-mode signals well if the tail current source is ideal.",
        "format": "markdown",
        "sha256": "168b506d9aeb3924dfd1e84705ce22f770a351a39083a97b0abe6adbacca766c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the circuit as a source-coupled differential pair with M2’s gate biased at Vb and output taken at M2’s drain. Its non-inverting gain for Vin with Vb fixed also agrees with the expected result.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 39774,
        "total_tokens": 40007,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 38712,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 233,
        "output_tokens": 39774,
        "total_tokens": 40007,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 38712,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The output is the source of the source-follower transistor \\(M_1\\), with \\(M_2\\) acting as a current-sink load. The inductance is an active/small-signal effect caused by \\(M_1\\), its gate–source capacitance \\(C_{gs}\\), and the gate resistance \\(R_S\\); it is not a physical coil.\n\nWhen the input source is killed to find \\(Z_{\\rm out}\\), the gate of \\(M_1\\) is connected to ac ground through \\(R_S\\). But \\(C_{gs}\\) couples the output node back to the gate. For a small test voltage \\(v_o\\) at \\(V_{\\rm out}\\),\n\n\\[\nv_g \\approx v_o\\frac{sR_S C_{gs}}{1+sR_S C_{gs}},\n\\qquad\nv_{gs}=v_g-v_o=-\\frac{v_o}{1+sR_S C_{gs}}.\n\\]\n\nThus the gate voltage cannot follow the source instantaneously; \\(R_S C_{gs}\\) introduces a delay/phase shift. Consequently the controlled current \\(g_m v_{gs}\\) supplied by \\(M_1\\) is not in phase with \\(v_o\\). The small-signal output admittance is approximately\n\n\\[\nY_{\\rm out}(s)\\approx g_{mb1}+g_{ds1}+g_{ds2}+\\frac{g_{m1}+sC_{gs}}{1+sR_S C_{gs}}+Y_{\\text{parasitics}} .\n\\]\n\nAt low frequencies,\n\n\\[\nY_{\\rm out}\\approx G+s\\big[C_{gs}(1-g_{m1}R_S)+C_p\\big],\n\\]\n\nwhere \\(G=g_{m1}+g_{mb1}+g_{ds1}+g_{ds2}\\) and \\(C_p\\) represents parasitic capacitance. If\n\n\\[\ng_{m1}R_S>1\n\\]\n\n(the effect is even stronger for large \\(R_S\\)), the reactive term in \\(Y_{\\rm out}\\) has the sign of an inductive susceptance. Equivalently, over that frequency range\n\n\\[\nZ_{\\rm out}\\approx \\frac{1}{G}+j\\omega L_{\\rm eq},\n\\]\n\nwith\n\n\\[\nL_{\\rm eq}\\approx \\frac{C_{gs}(g_{m1}R_S-1)}{G^2}\n\\approx \\frac{R_S C_{gs}}{g_{m1}}\n\\quad\\text{for }g_{m1}R_S\\gg1.\n\\]\n\nSo the circuit looks like a resistance with a positive reactive part: the current lags the applied voltage, which is exactly inductive behavior. Physically, \\(R_S\\) combined with \\(C_{gs}\\) delays the gate voltage, so the source follower’s channel current responds later than the output voltage. This active-inductor effect disappears if \\(R_S\\) is too small; at very high frequencies other parasitic capacitances dominate and the impedance becomes capacitive again. \\(M_2\\) mainly biases the stage and provides a high output resistance; it does not create the inductance.",
        "format": "markdown",
        "sha256": "37210c00ab0d371cf9125599f922d0e32b8d7b75201b7c7deef7f277c62ab3ff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and derives the gate–source feedback that makes the output impedance inductive when gm1RS > 1, with a consistent low-frequency inductance estimate. The high-frequency parasitic caveat is secondary and does not undermine the core explanation.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 818,
        "output_tokens": 25896,
        "total_tokens": 26714,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 818,
        "output_tokens": 25896,
        "total_tokens": 26714,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The output is not a real inductor; the circuit is acting as an **active/simulated inductor**. The effect comes from the upper transistor \\(M_1\\) operating as a source follower with a finite gate-source resistance \\(R_s\\) and its gate–source capacitance \\(C_{gs}\\).\n\nFor small-signal output impedance, set \\(V_{\\rm in}=0\\) and apply a test voltage \\(v_x\\) at \\(V_{\\rm out}\\). Let \\(v_g\\) be the gate voltage of \\(M_1\\). The gate is connected to ac ground through \\(R_s\\), while \\(C_{gs}\\) couples the gate to the output. Thus\n\n\\[\n\\frac{v_g}{R_s}+sC_{gs}(v_g-v_x)=0\n\\]\n\nso\n\n\\[\nv_g=\\frac{sR_s C_{gs}}{1+sR_s C_{gs}}v_x .\n\\]\n\nThe small-signal current that a test source must supply at the output, including the device’s \\(g_m\\), is approximately\n\n\\[\ni_x=(g_m+sC_{gs})(v_x-v_g)+G_L v_x ,\n\\]\n\nwhere \\(G_L\\) represents the parallel output resistance/capacitance of \\(M_1\\), \\(M_2\\), and any load. Ignoring the load for the moment,\n\n\\[\nY_{\\rm out}(s)=\\frac{i_x}{v_x}\n=\\frac{g_m+sC_{gs}}{1+sR_s C_{gs}} .\n\\]\n\nPutting \\(s=j\\omega\\),\n\n\\[\nY_{\\rm out}\n=\n\\frac{g_m+\\omega^2R_s C_{gs}^2\n+j\\omega C_{gs}(1-g_mR_s)}\n{1+(\\omega R_s C_{gs})^2}.\n\\]\n\nThe imaginary part of the admittance is negative when\n\n\\[\ng_mR_s>1.\n\\]\n\nA negative susceptance corresponds to an inductive reactance; equivalently, \\(Z_{\\rm out}=1/Y_{\\rm out}\\) has a positive imaginary part. At low frequencies this can be written as an equivalent series inductance\n\n\\[\nZ_{\\rm out}\\approx \\frac{1}{g_m}\n+j\\omega L_{\\rm eq},\n\\qquad\nL_{\\rm eq}\\approx\n\\frac{C_{gs}}{g_m}\\left(R_s-\\frac{1}{g_m}\\right),\n\\]\n\nwhich is positive for \\(R_s>1/g_m\\).\n\nPhysically, when the output voltage changes, the gate voltage does not follow instantly because of the \\(R_sC_{gs}\\) network. This produces a phase-shifted gate–source voltage and hence a channel current that lags the output voltage. A lagging current is the signature of an inductor. In other words, the transistor plus the gate-source capacitance behaves like a gyrator: it converts the capacitance into an effective inductance at the output.\n\nThe lower transistor \\(M_2\\) mainly supplies the bias current and presents an output resistance/capacitance in parallel; it does not create the inductance but lowers the \\(Q\\). At very high frequencies, the output capacitance and other parasitics (e.g., \\(C_{gd}\\), \\(C_{db}\\)) dominate and the terminal impedance again becomes capacitive. Thus the output impedance can be inductive only over the appropriate frequency band and when \\(R_s\\) is large enough. If \\(R_s\\) were zero (gate at ideal ac ground), the inductive effect would disappear.",
        "format": "markdown",
        "sha256": "05c93d7a4dbf5eb660923e0337bbf1cfe9750dda9179bfac6258b22793f54e7c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and derives the output admittance and positive equivalent series inductance for Rs > 1/gm. The equations capture the Cgs-mediated frequency dependence; the parasitic high-frequency caveat does not undermine the explanation.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 818,
        "output_tokens": 18704,
        "total_tokens": 19522,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 818,
        "output_tokens": 18704,
        "total_tokens": 19522,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18005,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The “inductance” is not a real coil; it is an **active equivalent inductance** produced by the source follower when its gate is driven through a finite resistance.\n\nFor small-signal output impedance, set \\(V_{\\rm in}=0\\). Then the gate of \\(M_1\\) is not an ideal ac ground; it sees \\(R_S\\) to ground. The output node is coupled to the gate through \\(C_{gs}\\). If a test voltage \\(v_o\\) is applied at \\(V_{\\rm out}\\), the gate voltage is approximately\n\\[\n\\frac{v_g}{v_o}\\approx\n\\frac{sR_S C_{gs}}{1+sR_S(C_{gs}+C_{gd})},\n\\]\nwhere \\(s=j\\omega\\). Thus the gate-source voltage, and hence the controlled current \\(g_m v_{gs}\\), has a frequency-dependent magnitude and phase with respect to \\(v_o\\). At low frequency the gate is almost grounded and the output resistance is roughly \\(1/g_m\\); at higher frequency the gate begins to follow the source through \\(C_{gs}\\), reducing \\(v_{gs}\\) and making the port draw less current for the same applied voltage. That phase lag/current reduction is equivalent to an inductive reactance.\n\nA simple model (neglecting \\(C_{gd}\\), output capacitance, and finite \\(r_o\\)) gives\n\\[\nZ_{\\rm out}(s)\\approx \\frac{1+sR_S C_{gs}}{g_m+sC_{gs}}.\n\\]\nExpanding at low frequencies,\n\\[\nZ_{\\rm out}\\approx \\frac{1}{g_m}\n+s\\,\\frac{C_{gs}}{g_m}\\left(R_S-\\frac{1}{g_m}\\right)\n= \\frac{1}{g_m}+sL_{\\rm eq},\n\\]\nwith\n\\[\nL_{\\rm eq}\\approx \\frac{C_{gs}}{g_m}\n\\left(R_S-\\frac{1}{g_m}\\right).\n\\]\nTherefore, when\n\\[\nR_S>\\frac{1}{g_m},\n\\]\nthe output impedance has a positive reactance, i.e. it looks inductive. If \\(R_S\\) is smaller, the same simple model gives a capacitive reactance. Including the finite output resistances of \\(M_1\\) and \\(M_2\\) and the load capacitance only adds parallel real and capacitive components; over some frequency range the total impedance can still be inductive.\n\nPhysically, \\(C_{gs}\\), the transistor transconductance, and \\(R_S\\) form a gyrator-like active network that converts the gate capacitance into an equivalent inductance at the source. The bottom device \\(M_2\\) mainly supplies bias current and its output resistance appears in parallel; it does not create the effect, but it affects the damping \\(Q\\). This inductive output impedance is important because it can resonate with a capacitive load, causing peaking or ringing in a source-follower buffer.",
        "format": "markdown",
        "sha256": "5adb99762e6acfeff63485c96b4d9867cbea70d532b54778f921d1e6dcf681f3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains the low- to high-frequency transition from approximately 1/gm to RS as Cgs couples the gate to the source, and derives the inductive condition RS > 1/gm and equivalent inductance. Minor comments about loading do not affect the essential answer.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 768,
        "input_tokens": 818,
        "output_tokens": 24524,
        "total_tokens": 25342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23924,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 768,
        "input_tokens": 818,
        "output_tokens": 24524,
        "total_tokens": 25342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23924,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume both \\(M_1\\) and \\(M_2\\) are enhancement NMOS transistors, and the line from \\(V_{out}\\) down to \\(M_2\\) is a real connection to the gate of \\(M_2\\). Then the circuit is a common-source stage \\(M_1\\) with an active feedback/current-sink transistor \\(M_2\\) controlled by the output.\n\n### 1. Connections and operation\n- \\(M_1\\): gate \\(=V_X\\), source \\(=0\\), drain \\(=V_{out}\\). It acts as an inverting common-source amplifier.\n- \\(R_{D1}\\): converts the drain current of \\(M_1\\) into an output voltage.\n- \\(M_2\\): drain \\(=V_X\\), source \\(=0\\), gate \\(=V_{out}\\). It forms a feedback path from output back to node \\(X\\).\n- The current source injects \\(I_{in}\\) into node \\(X\\).\n\nThus the input current controls \\(V_X\\), \\(M_1\\) converts \\(V_X\\) into an output current/voltage, and \\(M_2\\) feeds the output back to the input node. Depending on the bias of \\(M_2\\), the circuit can behave as an active-feedback transimpedance stage; because the feedback has a positive-feedback tendency, it can also exhibit hysteresis/latching if \\(M_2\\) is not strongly in triode.\n\n### 2. DC operating point\nLet\n\\[\nI_D=\\frac12\\mu_n C_{ox}\\frac{W}{L}(V_{GS}-V_T)^2\n\\]\nin saturation, and ignore body effect and channel-length modulation initially.\n\nAt node \\(X\\):\n\\[\nI_{D2}=I_{in}\n\\]\nAt the output:\n\\[\nI_{D1}=\\frac{V_{DD}-V_{out}}{R_{D1}}\n\\]\nIf both transistors are in saturation:\n\\[\nV_{out}=V_{T2}+\\sqrt{\\frac{2I_{in}}{\\beta_2}},\n\\qquad \\beta_i=\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_i\n\\]\nand\n\\[\nV_X=V_{T1}+\\sqrt{\\frac{2(V_{DD}-V_{out})}{\\beta_1 R_{D1}}}.\n\\]\nValid if\n\\[\nV_{out}\\ge V_X-V_{T1}\n\\]\nfor \\(M_1\\) saturation, and\n\\[\nV_X\\ge V_{out}-V_{T2}\n\\]\nfor \\(M_2\\) saturation.\n\nIf \\(M_2\\) is in triode, which is common for an active feedback device, replace its current equation by\n\\[\nI_{in}=\\beta_2\\left[(V_{out}-V_{T2})V_X-\\frac{V_X^2}{2}\\right],\n\\]\nwith \\(V_X<V_{out}-V_{T2}\\), and solve together with the \\(M_1\\) load equation.\n\n### 3. Small-signal analysis\nLet\n\\[\ng_{mi}=\\frac{\\partial I_{Di}}{\\partial V_{GSi}},\n\\qquad\ng_{dsi}=\\frac1{r_{oi}}=\\frac{\\partial I_{Di}}{\\partial V_{DSi}}.\n\\]\nUsing \\(i_{in}\\) positive into node \\(X\\), \\(v_x\\), and \\(v_{out}\\):\n\nKCL at node \\(X\\):\n\\[\ni_{in}=g_{m2}v_{out}+g_{ds2}v_x\n\\]\nKCL at the output:\n\\[\ng_{m1}v_x+\\left(g_{ds1}+\\frac{1}{R_{D1}}\\right)v_{out}=0\n\\]\nSolving:\n\\[\n\\boxed{\n\\frac{v_{out}}{i_{in}}\n=\n\\frac{1}{\ng_{m2}\n-\n\\frac{g_{ds2}}{g_{m1}}\n\\left(g_{ds1}+\\frac{1}{R_{D1}}\\right)\n}}\n\\]\nThe small-signal voltage gain from \\(V_X\\) to \\(V_{out}\\) is the usual common-source gain:\n\\[\n\\boxed{\n\\frac{v_{out}}{v_x}\n=\n-\\frac{g_{m1}}{g_{ds1}+1/R_{D1}}\n\\approx\n-g_{m1}(R_{D1}\\|r_{o1})\n}\n\\]\nThe small-signal input resistance at node \\(X\\) is\n\\[\n\\boxed{\nR_{in,X}\n=\n\\frac{v_x}{i_{in}}\n=\n\\frac{1}{\ng_{ds2}\n-\n\\frac{g_{m1}g_{m2}}{g_{ds1}+1/R_{D1}}\n}\n}\n\\]\nIf \\(g_{ds2}\\) is very small, i.e. \\(M_2\\) behaves almost as an ideal current source, the feedback can make \\(R_{in,X}\\) negative; in practice \\(M_2\\) is often biased in triode so that \\(g_{ds2}\\) is large enough for stable linear operation.\n\nA useful approximate form when channel-length modulation is neglected and \\(M_2\\) is in saturation is\n\\[\n\\frac{v_{out}}{i_{in}}\\approx \\frac{1}{g_{m2}},\n\\qquad\n\\frac{v_{out}}{v_x}\\approx -g_{m1}R_{D1}.\n\\]\n\n### 4. Stability note\nBecause \\(V_{out}\\) drives the gate of \\(M_2\\), there is a positive-feedback path. If the loop gain is large, the circuit can latch or exhibit hysteresis. A rough condition for positive small-signal input/output resistance is\n\\[\ng_{ds2}\\left(g_{ds1}+\\frac{1}{R_{D1}}\\right)\n>\ng_{m1}g_{m2}.\n\\]\nIf this condition is not met, the circuit can behave as a Schmitt trigger/latch rather than a linear amplifier.\n\n### If \\(V_{out}\\) is not actually connected to \\(M_2\\)\nIf the intended circuit is the standard NMOS current mirror in which \\(M_2\\) is diode-connected at node \\(X\\), then the results simplify to:\n\\[\nI_{D2}=I_{in},\\qquad\nI_{D1}\\approx \\frac{\\beta_1}{\\beta_2}I_{in},\n\\]\n\\[\nV_{out}=V_{DD}-I_{D1}R_{D1},\n\\]\nand small-signal:\n\\[\n\\frac{v_{out}}{i_{in}}\n\\approx\n-\\frac{g_{m1}}{g_{m2}}\\bigl(R_{D1}\\|r_{o1}\\bigr),\n\\qquad\nR_{in,X}\\approx \\frac{1}{g_{m2}},\n\\qquad\nR_{out}\\approx R_{D1}\\|r_{o1}.\n\\]\n\nSo, as drawn, the circuit is best described as a common-source NMOS stage with active shunt feedback through \\(M_2\\); its behavior is set by the bias region of \\(M_2\\), and the small-signal transimpedance is the boxed expression above.",
        "format": "markdown",
        "sha256": "8efa2386e5e4af71eb056d261799cf4b0e8f536d12a82bb99f887bd1fee60f4a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that M2’s gate is tied to Vout, recognizes the positive-feedback loop through M1 and M2, and notes possible negative input resistance and latching. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1049,
        "output_tokens": 39596,
        "total_tokens": 40645,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35166,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1049,
        "output_tokens": 39596,
        "total_tokens": 40645,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35166,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming the MOSFETs are NMOS, are biased in saturation, and the lower device is connected as the drawing indicates:\n\n- \\(M_1\\): gate \\(=X\\), drain \\(=V_{\\rm out}\\), source \\(=0\\)\n- \\(M_2\\): gate \\(=V_{\\rm out}\\), drain \\(=X\\), source \\(=0\\)\n- \\(I_{\\rm in}\\) injects current into node \\(X\\)\n- \\(R_{D1}\\) is between \\(V_{DD}\\) and \\(V_{\\rm out}\\)\n\nThus \\(M_1\\) is a common-source stage, and \\(M_2\\) provides cross-coupled feedback from \\(V_{\\rm out}\\) to \\(X\\). The feedback is positive, so the small-signal port resistances can be negative; stability depends on the source/load.\n\n## 1. DC operating point\n\nLet  \n\\[\n\\beta_i=\\mu_nC_{ox}\\left(\\frac{W}{L}\\right)_i,\\qquad V_T=V_{Tn}.\n\\]\nNeglecting channel-length modulation initially,\n\\[\nI_{D2}=\\frac{\\beta_2}{2}(V_{\\rm out}-V_T)^2,\\qquad\nI_{D1}=\\frac{\\beta_1}{2}(X-V_T)^2.\n\\]\n\nKCL at \\(X\\) and at \\(V_{\\rm out}\\) gives\n\\[\nI_{\\rm in}=I_{D2},\n\\]\n\\[\n\\frac{V_{DD}-V_{\\rm out}}{R_{D1}}=I_{D1}.\n\\]\n\nTherefore, for both devices in saturation,\n\\[\n\\boxed{V_{\\rm out}=V_T+\\sqrt{\\frac{2I_{\\rm in}}{\\beta_2}}}\n\\]\nand\n\\[\n\\boxed{X=V_T+\\sqrt{\\frac{2(V_{DD}-V_{\\rm out})}{\\beta_1 R_{D1}}}}\n\\]\nprovided\n\\[\nV_{\\rm out}\\ge X-V_T \\qquad (M_1\\ \\text{saturation}),\n\\]\n\\[\nX\\ge V_{\\rm out}-V_T \\qquad (M_2\\ \\text{saturation}),\n\\]\nand both devices are on. If these inequalities fail, the triode equations must be used.\n\nIncluding channel-length modulation: replace the currents by\n\\[\nI_{D1}=\\frac{\\beta_1}{2}(X-V_T)^2(1+\\lambda_1 V_{\\rm out}),\n\\]\n\\[\nI_{D2}=\\frac{\\beta_2}{2}(V_{\\rm out}-V_T)^2(1+\\lambda_2 X),\n\\]\nand solve the two KCL equations numerically/implicitly.\n\n## 2. Small-signal model\n\nDefine\n\\[\ng_{mi}=\\sqrt{2\\beta_i I_{Di}},\\qquad\nr_{oi}=\\frac{1}{\\lambda_i I_{Di}},\n\\]\nor equivalently \\(g_{mi}=2I_{Di}/(V_{GSi}-V_T)\\), \\(r_{oi}=V_{Ai}/I_{Di}\\).\n\nFor no external load at \\(V_{\\rm out}\\), let\n\\[\nR_P=R_{D1}\\parallel r_{o1},\n\\qquad\n\\frac1{R_P}=\\frac1{R_{D1}}+\\frac1{r_{o1}}.\n\\]\n\nSmall-signal KCL at output and at \\(X\\):\n\\[\ng_{m1}v_x+\\frac{v_{\\rm out}}{R_{D1}}+\\frac{v_{\\rm out}}{r_{o1}}=0,\n\\]\n\\[\ni_{\\rm in}=g_{m2}v_{\\rm out}+\\frac{v_x}{r_{o2}}.\n\\]\n\nSolving,\n\\[\n\\boxed{\n\\frac{v_{\\rm out}}{i_{\\rm in}}\n=\n\\frac{1}{\ng_{m2}\n-\\frac{1}{g_{m1}r_{o2}}\n\\left(\\frac1{R_{D1}}+\\frac1{r_{o1}}\\right)\n}\n}\n\\]\nor equivalently\n\\[\n\\boxed{\n\\frac{v_{\\rm out}}{i_{\\rm in}}\n=\n\\frac{g_{m1}r_{o2}R_P}\n{g_{m1}g_{m2}r_{o2}R_P-1}\n}\n\\]\nwith \\(R_P=R_{D1}\\parallel r_{o1}\\).\n\nIf \\(r_{o2}\\to\\infty\\), this reduces to\n\\[\n\\boxed{\\frac{v_{\\rm out}}{i_{\\rm in}}\\approx \\frac1{g_{m2}}.}\n\\]\n\nIf a voltage is applied directly at \\(X\\), the common-source voltage gain is\n\\[\n\\boxed{\\frac{v_{\\rm out}}{v_x}\n=-g_{m1}(R_{D1}\\parallel r_{o1}).}\n\\]\n\n## 3. Small-signal resistances\n\nThe small-signal resistance seen at node \\(X\\) is\n\\[\n\\boxed{\nR_{{\\rm in},X}\n=\n\\frac{v_x}{i_{\\rm in}}\n=\n\\frac{1}{\n\\frac1{r_{o2}}\n-g_{m1}g_{m2}(R_{D1}\\parallel r_{o1})\n}\n}\n\\]\nor, in the form showing the negative resistance,\n\\[\n\\boxed{\nR_{{\\rm in},X}\n=\n-\\frac{1}{\ng_{m1}g_{m2}(R_{D1}\\parallel r_{o1})\n-\\frac1{r_{o2}}\n}.\n}\n\\]\nIt is negative for typical large \\(g_m r_o\\) because of the positive-feedback loop.\n\nThe output resistance looking into \\(V_{\\rm out}\\), with the input current source set to zero, is\n\\[\n\\boxed{\nR_{\\rm out}\n=\n\\frac{1}{\n\\frac1{R_{D1}}+\\frac1{r_{o1}}\n-g_{m1}g_{m2}r_{o2}\n}.\n}\n\\]\nThis is also typically a small negative incremental resistance. If the input current source has finite small-signal output resistance \\(R_s\\), replace \\(r_{o2}\\) in the feedback term by \\(r_{o2}\\parallel R_s\\):\n\\[\nR_{\\rm out}\n=\n\\frac{1}{\n\\frac1{R_{D1}}+\\frac1{r_{o1}}\n-g_{m1}g_{m2}(r_{o2}\\parallel R_s)\n}.\n\\]\n\nFor stable amplifier operation, the net conductance at the output node should remain positive:\n\\[\n\\boxed{\n\\frac1{R_{D1}}+\\frac1{r_{o1}}+\\frac1{R_L}\n>\ng_{m1}g_{m2}r_{o2}\n}\n\\]\nwhere \\(R_L\\) is the external load. Otherwise the positive feedback can cause oscillation or latch-like behavior.\n\n## Summary\n\n- \\(V_{\\rm out}\\) is primarily set by the diode-like characteristic of \\(M_2\\):\n  \\[\n  V_{\\rm out}\\approx V_T+\\sqrt{\\frac{2I_{\\rm in}}{\\beta_2}}.\n  \\]\n- The small-signal current-to-voltage gain is approximately\n  \\[\n  \\frac{v_{\\rm out}}{i_{\\rm in}}\\approx \\frac1{g_{m2}}.\n  \\]\n- Finite \\(r_{o2}\\) makes the feedback loop active; it reduces the effective denominator, increasing gain and producing negative small-signal input/output resistance.\n- If the lower transistor was instead intended to be diode-connected at node \\(X\\) (the usual current-mirror connection), then there is no feedback from \\(V_{\\rm out}\\) to \\(M_2\\), and the standard current mirror results apply:\n  \\[\n  V_{\\rm out}=V_{DD}-R_{D1}I_{D1},\n  \\]\n  \\[\n  \\frac{v_{\\rm out}}{i_{\\rm in}}\n  \\approx -\\frac{g_{m1}R_{D1}}{g_{m2}},\n  \\qquad\n  R_{\\rm out}=R_{D1}\\parallel r_{o1}.\n  \\]",
        "format": "markdown",
        "sha256": "fbf03e56d3b4fcfe78c94ec0b38993173f9d1750e6b9b0186bd3cfb8549168c5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate connection to Vout, the positive-feedback loop, and the resulting negative input resistance and possible instability. Its small-signal input-resistance expression matches the golden result; the additional analysis does not undermine the essential answer.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1049,
        "output_tokens": 35991,
        "total_tokens": 37040,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 32630,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1049,
        "output_tokens": 35991,
        "total_tokens": 37040,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 32630,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume both devices are enhancement-mode n-channel MOSFETs with their sources grounded, and neglect channel-length modulation initially. The circuit is a current mirror / current-to-voltage converter:\n\n- \\(M_2\\) is diode-connected (gate and drain at node \\(X\\)).\n- \\(M_1\\) is the output transistor.\n- \\(I_{\\rm in}\\) sets the gate voltage of both transistors, and \\(M_1\\) sinks a mirrored current through \\(R_{D1}\\), producing \\(V_{\\rm out}\\).\n- Increasing \\(I_{\\rm in}\\) increases the current through \\(M_1\\) and therefore lowers \\(V_{\\rm out}\\): the stage is inverting.\n\nLet\n\\[\n\\beta_i=\\mu_n C_{ox}\\left(\\frac WL\\right)_i,\\qquad \nI_D=\\frac{\\beta_i}{2}(V_{GS}-V_T)^2\n\\]\nin saturation.\n\n### 1. Node \\(X\\) and \\(M_2\\)\n\nFor positive \\(I_{\\rm in}\\),\n\\[\nI_{D2}=I_{\\rm in}.\n\\]\nBecause \\(M_2\\) is diode-connected, \\(V_{GS2}=V_{DS2}=V_X\\). It is in saturation whenever it is on, so\n\\[\nI_{\\rm in}=\\frac{\\beta_2}{2}(V_X-V_T)^2,\n\\]\ngiving\n\\[\nV_X=V_T+\\sqrt{\\frac{2I_{\\rm in}}{\\beta_2}}.\n\\]\nIf \\(I_{\\rm in}=0\\) ideally, both transistors are off.\n\n### 2. Output while \\(M_1\\) is saturated\n\nThe resistor current is\n\\[\nI_{D1}=\\frac{V_{DD}-V_{\\rm out}}{R_{D1}}.\n\\]\nWith \\(M_1\\) saturated,\n\\[\nI_{D1}=\\frac{\\beta_1}{2}(V_X-V_T)^2.\n\\]\nTherefore\n\\[\nV_{\\rm out}=V_{DD}-R_{D1}\\frac{\\beta_1}{\\beta_2}I_{\\rm in}.\n\\]\nIf the two transistors are matched, \\(\\beta_1=\\beta_2=\\beta\\):\n\\[\n\\boxed{V_{\\rm out}=V_{DD}-R_{D1}I_{\\rm in}}\n\\]\nwhile \\(M_1\\) remains saturated.\n\nThe saturation condition for \\(M_1\\) is\n\\[\nV_{\\rm out}\\ge V_X-V_T,\n\\]\ni.e.\n\\[\nV_{DD}-R_{D1}\\frac{\\beta_1}{\\beta_2}I_{\\rm in}\n\\ge\n\\sqrt{\\frac{2I_{\\rm in}}{\\beta_2}}\n\\]\n(with equal thresholds).\n\n### 3. When \\(M_1\\) enters triode\n\nAs \\(I_{\\rm in}\\) increases, \\(V_{\\rm out}\\) falls. When\n\\[\nV_{\\rm out}<V_X-V_T,\n\\]\n\\(M_1\\) enters the triode region. Then\n\\[\n\\frac{V_{DD}-V_{\\rm out}}{R_{D1}}\n=\n\\beta_1\\left[\n(V_X-V_T)V_{\\rm out}\n-\\frac{V_{\\rm out}^2}{2}\n\\right],\n\\]\nwith\n\\[\nV_X=V_T+\\sqrt{\\frac{2I_{\\rm in}}{\\beta_2}}.\n\\]\nSolving this quadratic gives \\(V_{\\rm out}\\), choosing the root with\n\\[\n0\\le V_{\\rm out}<V_X-V_T.\n\\]\nFor very large \\(I_{\\rm in}\\), \\(M_1\\) is deeply in triode and\n\\[\nV_{\\rm out}\\approx\n\\frac{V_{DD}}{1+\\beta_1 R_{D1}(V_X-V_T)}\n\\longrightarrow 0\n\\]\n(as \\(V_X\\) becomes large).\n\n### 4. Region summary\n\n| Region | Condition (matched devices) | \\(V_{\\rm out}\\) |\n|---|---|---|\n| \\(M_1,M_2\\) off | \\(I_{\\rm in}=0\\) | \\(V_{\\rm out}\\approx V_{DD}\\) |\n| \\(M_1\\) saturation; \\(M_2\\) saturation | \\(0<I_{\\rm in}<I_{\\rm in,b}\\) | \\(V_{\\rm out}=V_{DD}-R_{D1}I_{\\rm in}\\) for matched devices |\n| \\(M_1\\) triode; \\(M_2\\) saturation | \\(I_{\\rm in}>I_{\\rm in,b}\\) | solve the triode equation above; \\(V_{\\rm out}\\) tends toward \\(0\\) |\n\nHere the boundary \\(I_{\\rm in,b}\\) is found from \\(V_{\\rm out}=V_X-V_T\\). If \\(V_{\\rm ov,b}=V_{X,b}-V_T\\), then\n\\[\n\\frac{\\beta_1}{2}V_{\\rm ov,b}^2\n=\n\\frac{V_{DD}-V_{\\rm ov,b}}{R_{D1}},\n\\]\nand\n\\[\nI_{\\rm in,b}=\\frac{\\beta_2}{2}V_{\\rm ov,b}^2.\n\\]\nFor matched transistors this is the point at which the linear relation \\(V_{\\rm out}=V_{DD}-R_{D1}I_{\\rm in}\\) stops being valid.\n\n### 5. Nonidealities and small-signal behavior\n\nWith channel-length modulation \\((\\lambda\\neq0)\\), the mirror ratio is not exact, and one solves implicitly:\n\\[\n\\frac{V_{DD}-V_{\\rm out}}{R_{D1}}\n=\n\\frac{\\beta_1}{2}(V_X-V_T)^2(1+\\lambda V_{\\rm out}),\n\\]\n\\[\nI_{\\rm in}\n=\n\\frac{\\beta_2}{2}(V_X-V_T)^2(1+\\lambda V_X).\n\\]\nThus \\(M_1\\) has a finite small-signal output resistance \\(r_{o1}\\).\n\nAbout a bias point in saturation, for an incremental input current \\(i_{\\rm in}\\),\n\\[\nv_x\\approx i_{\\rm in}\\left(\\frac1{g_{m2}}\\parallel r_{o2}\\right),\n\\]\nand\n\\[\nv_{\\rm out}\\approx\n-g_{m1}(R_{D1}\\parallel r_{o1})v_x.\n\\]\nNeglecting \\(r_{o2}\\),\n\\[\n\\boxed{\n\\frac{v_{\\rm out}}{i_{\\rm in}}\n\\approx\n-\\frac{g_{m1}}{g_{m2}}\\,(R_{D1}\\parallel r_{o1})\n}\n\\]\nand with \\(\\lambda=0\\), matched devices, this reduces to\n\\[\n\\boxed{\\frac{v_{\\rm out}}{i_{\\rm in}}\\approx -R_{D1}}.\n\\]\nIf the sizes differ,\n\\[\n\\frac{v_{\\rm out}}{i_{\\rm in}}\\approx\n-\\frac{\\beta_1}{\\beta_2}R_{D1}\n\\]\nfor \\(\\lambda=0\\).\n\nOverall: the circuit is a current-controlled current mirror with a resistive load. It produces a high output for zero/low input current, lowers the output almost linearly with \\(I_{\\rm in}\\) while \\(M_1\\) is saturated, and saturates near ground once \\(I_{\\rm in}\\) is large enough to drive \\(M_1\\) into triode. Numerical values require \\(V_{DD}\\), \\(R_{D1}\\), transistor \\(W/L\\) values, \\(\\mu_nC_{ox}\\), and \\(V_T\\).",
        "format": "markdown",
        "sha256": "96d1026c5d84506ba57114558fb705b946783278ae86adde456fe8b1fa332627"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly places the input current at X and recognizes M1’s inverting, resistively loaded action, but wrongly treats M2 as diode-connected and the circuit as a current mirror, missing the positive-feedback loop through M1 and M2.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1049,
        "output_tokens": 28067,
        "total_tokens": 29116,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23420,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1049,
        "output_tokens": 28067,
        "total_tokens": 29116,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23420,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming low-frequency small-signal operation, the transistors biased in saturation, and neglecting channel-length modulation and body effect (\\(r_o\\to\\infty\\)), the circuit is a **shunt-shunt negative-feedback transimpedance amplifier**:\n\n- \\(M_1\\) is a common-gate input transistor whose gate is at ac ground through the bias source \\(V_b\\).\n- \\(M_2\\) is a common-source inverting gain stage.\n- \\(R_F\\) feeds the output voltage back to the input node, forming negative feedback.\n\nLet\n\\[\nv_s=\\text{small-signal voltage at the source of }M_1,\\qquad\nv_o=V_{\\rm out}\\text{ (small-signal)}\n\\]\nand let \\(I_{\\rm in}\\) be positive in the direction of the arrow in the figure.\n\n### Small-signal equations\n\\[\nv_x=g_{m1}R_{D1}v_s\n\\]\n\\[\n\\left(\\frac1{R_{D2}}+\\frac1{R_F}\\right)v_o\n+g_{m2}v_x-\\frac{v_s}{R_F}=0\n\\]\n\\[\nI_{\\rm in}=\\left(g_{m1}+\\frac1{R_F}\\right)v_s-\\frac{v_o}{R_F}\n\\]\n\nSolving gives the closed-loop transresistance:\n\\[\n\\boxed{\nZ_T=\\frac{V_{\\rm out}}{I_{\\rm in}}\n=\n\\frac{\nR_{D2}\\left(1-g_{m1}g_{m2}R_{D1}R_F\\right)\n}{\n1+g_{m1}(R_F+R_{D2})\n+g_{m1}g_{m2}R_{D1}R_{D2}\n}\n}\n\\]\nFor the usual case of large loop gain,\n\\[\ng_{m1}g_{m2}R_{D1}R_{D2}\\gg 1+g_{m1}(R_F+R_{D2}),\n\\]\nthis reduces to\n\\[\n\\boxed{V_{\\rm out}\\approx -I_{\\rm in}R_F}\n\\]\nso the transresistance is approximately \\(-R_F\\). The negative sign is because an increasing input current raises \\(v_x\\), turning on \\(M_2\\) more and pulling \\(V_{\\rm out}\\) down. If \\(I_{\\rm in}\\) is defined in the opposite direction, the sign reverses.\n\nThe small-signal input resistance seen by the current source is\n\\[\n\\boxed{\nR_{\\rm in}=\\frac{v_s}{I_{\\rm in}}\n=\n\\frac{\nR_F+R_{D2}\n}{\n1+g_{m1}(R_F+R_{D2})\n+g_{m1}g_{m2}R_{D1}R_{D2}\n}\n}\n\\]\nThus negative feedback lowers the input resistance; without feedback,\n\\[\nR_F\\to\\infty \\quad\\Rightarrow\\quad R_{\\rm in}\\to \\frac1{g_{m1}}.\n\\]\n\nThe output resistance, with the input current source opened, is\n\\[\n\\boxed{\nR_{\\rm out}\n=\n\\left[\n\\frac1{R_{D2}}\n+\n\\frac{g_{m1}(1+g_{m2}R_{D1})}\n{1+g_{m1}R_F}\n\\right]^{-1}\n}\n\\]\nso feedback also lowers the output resistance; with \\(R_F\\to\\infty\\), \\(R_{\\rm out}\\to R_{D2}\\).\n\nThe voltage gain from the input node to the output node is\n\\[\n\\boxed{\nA_v=\\frac{v_o}{v_s}\n=\n\\frac{\nR_{D2}\\left(1-g_{m1}g_{m2}R_{D1}R_F\\right)\n}{\nR_{D2}+R_F\n}\n}\n\\]\nand without feedback (\\(R_F\\to\\infty\\)),\n\\[\nA_v\\to -g_{m1}g_{m2}R_{D1}R_{D2}.\n\\]\n\n### Bias conditions\nFor saturation (assuming \\(M_2\\)'s source is ground),\n\\[\nM_1:\\quad V_X\\ge V_b-V_{TH1},\n\\]\n\\[\nM_2:\\quad V_{\\rm out}\\ge V_X-V_{TH2},\n\\]\ntogether with \\(V_b-V_S>V_{TH1}\\), where \\(V_S\\) is the dc voltage at the input node. \\(R_{D1}\\), \\(R_{D2}\\), \\(V_b\\), and \\(R_F\\) must be chosen to satisfy these inequalities.\n\n### Main conclusions\n- The circuit converts input current to output voltage; ideally \\(V_{\\rm out}\\approx -I_{\\rm in}R_F\\).\n- \\(M_1\\) provides a low-impedance current-input node.\n- \\(M_2\\) supplies inverting gain, allowing large loop gain.\n- \\(R_F\\) sets the transresistance, stabilizes the dc operating point, lowers input/output resistance, and increases usable bandwidth, subject to stability/compensation requirements.\n\nIf the bulk of \\(M_1\\) is grounded, replace \\(g_{m1}\\) in the formulas by \\(g_{m1}+g_{mb1}\\). Finite \\(r_{o1},r_{o2}\\) can be included by adding their conductances in the small-signal nodal equations; the approximations above remain valid when the loop gain is large.",
        "format": "markdown",
        "sha256": "6daad7376de703b1057aa833106c9b3acef2d13f37a0a98a45a65f2227d4d6c9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from the output to the input node, forming a transimpedance amplifier. It also gives the expected −RF high-loop-gain result and low input resistance.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1027,
        "output_tokens": 44169,
        "total_tokens": 45196,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33798,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1027,
        "output_tokens": 44169,
        "total_tokens": 45196,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33798,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "A complete numerical analysis is impossible without transistor sizes, bias voltages, and resistor values, but the circuit can be analyzed symbolically. Assume both transistors are NMOS and are biased in saturation, \\(V_{DD}\\) and \\(V_b\\) are ac grounds, and channel-length modulation/body effect are initially neglected. The circuit is a shunt–shunt negative-feedback current-to-voltage amplifier (transimpedance amplifier): \\(M_1\\) is a common-gate input stage, \\(M_2\\) is a common-source output stage, and \\(R_F\\) feeds the output back to the input node.\n\nLet  \n- \\(v_s\\) = small-signal voltage at the source of \\(M_1\\) (input node),  \n- \\(v_x\\) = small-signal voltage at node \\(X\\),  \n- \\(v_o=V_{\\rm out}\\),  \n- \\(i_{\\rm in}\\) = input current in the arrow direction (injected into the input node).\n\nFor the first-order model, \\(r_o\\to\\infty\\), \\(g_{mb}=0\\):\n\n\\[\ng_{m1}v_s+\\frac{v_s-v_o}{R_F}=i_{\\rm in}\n\\]\n\n\\[\nv_x=g_{m1}R_{D1}v_s\n\\]\n\n\\[\n\\frac{v_o}{R_{D2}}+g_{m2}v_x+\\frac{v_o-v_s}{R_F}=0\n\\]\n\nSolving gives the closed-loop transresistance\n\n\\[\n\\boxed{\nR_T\\equiv \\frac{v_o}{i_{\\rm in}}\n=\n-\\frac{g_{m1}g_{m2}R_{D1}-\\frac{1}{R_F}}\n{g_{m1}\\left(\\frac1{R_{D2}}+\\frac1{R_F}\\right)\n+\\frac{1}{R_{D2}R_F}\n+\\frac{g_{m1}g_{m2}R_{D1}}{R_F}}\n}\n\\]\n\nor, equivalently,\n\n\\[\n\\boxed{\nR_T=\n-\\frac{R_{D2}\\left(g_{m1}g_{m2}R_{D1}R_F-1\\right)}\n{g_{m1}(R_F+R_{D2})+1+g_{m1}g_{m2}R_{D1}R_{D2}}\n}\n\\]\n\nThe input resistance seen at the source of \\(M_1\\) is\n\n\\[\n\\boxed{\nR_{\\rm in}=\\frac{v_s}{i_{\\rm in}}\n=\n\\frac{R_F+R_{D2}}\n{1+g_{m1}\\!\\left(R_F+R_{D2}+g_{m2}R_{D1}R_{D2}\\right)}\n}\n\\]\n\nThe output resistance, measured with the input current source open-circuited, is\n\n\\[\n\\boxed{\nR_{\\rm out}\n=\n\\left[\n\\frac1{R_{D2}}\n+\n\\frac{g_{m1}(1+g_{m2}R_{D1})}{1+g_{m1}R_F}\n\\right]^{-1}\n}\n\\]\n\nFor high loop gain, approximately\n\n\\[\nL \\approx \\frac{g_{m2}R_{D1}R_{D2}}{R_F},\n\\]\n\nand if \\(L\\gg1\\),\n\n\\[\n\\boxed{R_T\\approx -R_F}\n\\]\n\nso the current-to-voltage gain is set mainly by the feedback resistor. The common-gate input and shunt feedback make the input resistance small:\n\n\\[\nR_{\\rm in}\\approx \\frac{1/g_{m1}}{1+L}\n\\quad\\text{(for \\(R_F\\gg R_{D2}\\))},\n\\]\n\nand the output resistance is also reduced by feedback:\n\n\\[\nR_{\\rm out}\\approx \\frac{R_{D2}}{1+L}.\n\\]\n\nThe feedback current, with the arrow shown from output to input, is\n\n\\[\ni_{RF}=\\frac{v_o-v_s}{R_F}.\n\\]\n\nIn the high-gain limit the input current is almost entirely supplied through \\(R_F\\):\n\n\\[\ni_{RF}\\approx -i_{\\rm in},\n\\qquad\nv_o\\approx -R_F i_{\\rm in}.\n\\]\n\nThus, for a positive current injected into the input node, the output decreases. If the input current arrow is reversed, all signs of \\(v_o\\) and \\(i_{RF}\\) reverse.\n\nTo include \\(r_{o1},r_{o2}\\) and body effect, replace \\(g_{m1}\\) by an effective input conductance\n\n\\[\ng_i=\\frac{g_{m1}+g_{mb1}+g_{ds1}}{1+g_{ds1}R_{D1}},\n\\qquad g_{ds1}=1/r_{o1},\n\\]\n\nand replace \\(1/R_{D2}\\) by\n\n\\[\ng_o=\\frac1{R_{D2}}+g_{ds2},\n\\qquad g_{ds2}=1/r_{o2}.\n\\]\n\nThen the compact results are\n\n\\[\nD=g_i g_o+\\frac{g_i+g_o}{R_F}\n+\\frac{g_i g_{m2}R_{D1}}{R_F},\n\\]\n\n\\[\n\\boxed{\nR_T=-\\frac{g_i g_{m2}R_{D1}-1/R_F}{D}\n}\n\\]\n\n\\[\n\\boxed{\nR_{\\rm in}=\\frac{g_o+1/R_F}{D}\n}\n\\]\n\n\\[\n\\boxed{\nR_{\\rm out}\n=\n\\left[\ng_o+\\frac{g_i(1+g_{m2}R_{D1})}{1+g_iR_F}\n\\right]^{-1}\n}\n\\]\n\nThe circuit operates as a negative-feedback transimpedance amplifier only if \\(M_1\\) and \\(M_2\\) remain in saturation:\n\n\\[\nV_{DS1}>V_{GS1}-V_{Tn},\\qquad\nV_{DS2}>V_{GS2}-V_{Tn}.\n\\]\n\nIf either device leaves saturation, these small-signal expressions must be modified using the appropriate MOSFET model. At higher frequencies, capacitances at the input, at node \\(X\\), and at the output introduce poles; \\(R_F\\) can then produce bandwidth extension but may also cause peaking, so stability/phase margin must be checked.",
        "format": "markdown",
        "sha256": "07ccc1a2be04c102297dbd575d00dc3d1d222e10ce60e2d0bf4057ed4ebc08f1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from the output to the input, forming a transimpedance amplifier. The stated high-gain result and sign are also consistent with the golden solution.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1027,
        "output_tokens": 50519,
        "total_tokens": 51546,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 49258,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1027,
        "output_tokens": 50519,
        "total_tokens": 51546,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 49258,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume both MOSFETs are NMOS biased in saturation, low-frequency operation, and (unless stated) ignore body effect and channel-length modulation. Let the small-signal voltage of the input/source node of \\(M_1\\) be \\(v_i\\), the drain of \\(M_1\\) be \\(v_X\\), and the output be \\(v_o\\). The input current arrow for \\(I_{in}\\) is taken upward into the input node.\n\n## 1. Circuit function\n\n- \\(M_1\\) operates as a common-gate transistor; its source is the low-impedance input node.\n- \\(R_{D1}\\) converts the small-signal current of \\(M_1\\) into a voltage at node \\(X\\), which drives the gate of \\(M_2\\).\n- \\(M_2\\) is a common-source inverting stage, so \\(v_o\\) is inverted relative to an increase of \\(v_X\\).\n- \\(R_F\\) provides shunt–shunt negative feedback: it senses \\(V_{out}\\) and injects a feedback current into the input node. The circuit is therefore a transimpedance amplifier (current input, voltage output).\n\nFor a positive current step injected into the input: \\(v_i\\uparrow\\), \\(v_X\\uparrow\\), \\(M_2\\) pulls more current, and \\(v_o\\downarrow\\). Feedback through \\(R_F\\) opposes the input disturbance, so feedback is negative.\n\n## 2. Small-signal analysis with \\(r_o\\to\\infty\\)\n\nWith \\(g_{m1},g_{m2}\\) the transistor transconductances:\n\n\\[\ni_{d1}=-g_{m1}v_i\n\\]\n\nKCL at node \\(X\\):\n\n\\[\n\\frac{v_X}{R_{D1}}+i_{d1}=0\n\\quad\\Rightarrow\\quad\nv_X=g_{m1}R_{D1}v_i .\n\\]\n\nAt the output,\n\n\\[\ni_{d2}=g_{m2}v_X,\n\\]\n\nand KCL gives\n\n\\[\n\\frac{v_o}{R_{D2}}+g_{m2}v_X+\\frac{v_o-v_i}{R_F}=0 .\n\\]\n\nDefine\n\n\\[\nR_L'=R_{D2}\\parallel R_F=\\frac{R_{D2}R_F}{R_{D2}+R_F}.\n\\]\n\nThen the “internal” voltage gain from the input node to the output is\n\n\\[\nA_v=\\frac{v_o}{v_i}\n=\nR_L'\\left(\\frac{1}{R_F}-g_{m1}g_{m2}R_{D1}\\right)\n=\n\\frac{R_{D2}}{R_{D2}+R_F}\n-g_{m1}g_{m2}R_{D1}R_L' .\n\\]\n\nNormally the second term dominates, so \\(A_v<0\\).\n\nThe input-node KCL is\n\n\\[\ni_{in}=g_{m1}v_i+\\frac{v_i-v_o}{R_F},\n\\]\n\nso the input admittance is\n\n\\[\nY_{in}=\\frac{i_{in}}{v_i}\n=\ng_{m1}+\\frac{1-A_v}{R_F}.\n\\]\n\nHence\n\n\\[\n\\boxed{\nZ_{in}=\\frac{v_i}{i_{in}}\n=\n\\frac{1}{g_{m1}+(1-A_v)/R_F}\n}\n\\]\n\nand the closed-loop transimpedance is\n\n\\[\n\\boxed{\nZ_T=\\frac{v_o}{i_{in}}\n=\n\\frac{A_v}{g_{m1}+(1-A_v)/R_F}\n=\n\\frac{A_vR_F}{1+g_{m1}R_F-A_v}\n}.\n\\]\n\nEquivalently,\n\n\\[\n\\boxed{\nV_{out}\\approx Z_T I_{in}\n}\n\\]\n\nfor small signals.\n\n## 3. High-loop-gain approximation\n\nDefine the loop-gain magnitude\n\n\\[\nT=\n\\frac{g_{m2}R_{D1}(R_{D2}\\parallel R_F)}{R_F}\n=\n\\frac{g_{m2}R_{D1}R_{D2}}{R_{D2}+R_F}.\n\\]\n\nIf \\(T\\gg1\\),\n\n\\[\n\\boxed{Z_T\\approx -R_F\\frac{T}{1+T}\\approx -R_F}\n\\]\n\nso\n\n\\[\n\\boxed{V_{out}\\approx -R_F I_{in}}.\n\\]\n\nThe sign follows the current-source arrow shown; reversing the arrow reverses the sign.\n\nAlso, the feedback greatly lowers the input resistance:\n\n\\[\n\\boxed{\nR_{in}\\approx \\frac{1}{g_{m1}(1+T)}\n}\n\\]\n\nor, including the direct feed-through term,\n\n\\[\nR_{in}\n=\n\\left[\ng_{m1}(1+T)+\\frac{1}{R_{D2}+R_F}\n\\right]^{-1}.\n\\]\n\nThe output resistance is approximately\n\n\\[\n\\boxed{\nR_{out}\\approx\nR_{D2}\\parallel\n\\frac{R_F+1/g_{m1}}{1+g_{m2}R_{D1}}\n}.\n\\]\n\nFor large loop gain this reduces to approximately \\(R_{D2}/(1+T)\\).\n\n## 4. Including channel-length modulation/body effect\n\nLet\n\n\\[\ng_{o1}=\\frac{1}{r_{o1}},\\qquad\ng_{o2}=\\frac{1}{r_{o2}},\n\\]\n\nand include \\(g_{mb1}\\) only if the body of \\(M_1\\) is not tied to its source. Then define\n\n\\[\nA_x=\\frac{v_X}{v_i}\n=\n\\frac{g_{m1}+g_{mb1}+g_{o1}}\n     {1/R_{D1}+g_{o1}},\n\\]\n\nand\n\n\\[\nR_L=\\frac{1}{1/R_{D2}+g_{o2}+1/R_F}.\n\\]\n\nThe finite-\\(r_o\\) results are\n\n\\[\n\\boxed{\nA_v=\\frac{v_o}{v_i}\n=\nR_L\\left(\n\\frac{1}{R_F}-g_{m2}A_x\n\\right)\n}\n\\]\n\n\\[\n\\boxed{\nY_{in}\n=\n\\frac{i_{in}}{v_i}\n=\n\\frac{A_x}{R_{D1}}+\\frac{1-A_v}{R_F}\n}\n\\]\n\n\\[\n\\boxed{\nZ_T=\\frac{v_o}{i_{in}}=\\frac{A_v}{Y_{in}}\n}\n\\]\n\nSetting \\(g_{o1}=g_{o2}=g_{mb1}=0\\) recovers the simpler expressions above. If an external load \\(R_L\\) is connected to the output, replace \\(R_{D2}\\) by \\(R_{D2}\\parallel R_L\\) in the output-load expressions.\n\n## 5. Bias and design notes\n\nFor proper operation both devices should stay saturated:\n\n- \\(M_1\\): \\(V_X>V_b-V_{TH1}\\) approximately, and \\(V_b-V_S>V_{TH1}\\).\n- \\(M_2\\): \\(V_{out}>V_X-V_{TH2}\\).\n- The bias current through \\(M_1\\) is approximately\n  \\[\n  I_{D1}=\\frac{V_{DD}-V_X}{R_{D1}},\n  \\]\n  and the feedback resistor also carries dc current, so \\(I_{in}\\), \\(R_F\\), and \\(V_{out}\\) bias are coupled.\n- A large \\(R_F\\) gives larger transimpedance but smaller loop gain; a small \\(R_F\\) gives lower input impedance, wider bandwidth, and greater feedback but lower transimpedance.\n- The circuit relies on negative feedback for its well-defined transimpedance. With parasitic capacitances at the input, \\(X\\), and output, ensure sufficient phase margin; the dominant high-frequency limitation is usually at the low-impedance input node and the \\(X\\)/output poles.\n\nIn short, this is a shunt-feedback common-gate/common-source transimpedance amplifier: for sufficiently large loop gain its current-to-voltage gain is set almost entirely by the feedback resistor,\n\n\\[\n\\boxed{V_{out}\\approx -I_{in}R_F,}\n\\]\n\nwhile feedback lowers both its input and output small-signal resistances and improves its bandwidth.",
        "format": "markdown",
        "sha256": "9f9471e2e4f8665e7f4711ecf5d7971476597e91645445358beee3d26c6f6c6d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from the output to the input, forming a transimpedance amplifier. This satisfies the golden solution’s full-credit rule.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1027,
        "output_tokens": 38053,
        "total_tokens": 39080,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1027,
        "output_tokens": 38053,
        "total_tokens": 39080,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36353,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "### Assumptions\n- \\(M_1\\) is an NMOS transistor biased by \\(V_b\\).\n- \\(M_2\\) is a PMOS transistor connected to \\(V_{DD}\\).\n- The unlabeled lower current source is a bias sink; call it \\(I_B\\). It only shifts the dc operating point. If it is not intended, set \\(I_B=0\\).\n- Channel-length modulation and body effect are neglected in the first-order equations. For body effect, replace \\(g_{m1}\\) by \\(g_{m1}+g_{mb1}\\).\n\nLet the lower common node be \\(X\\).\n\n## 1. Basic operation\nThe circuit is a negative-feedback CMOS stage:\n- \\(M_1\\) is a common-gate/current-sink device whose gate is fixed at \\(V_b\\).\n- \\(M_2\\) is a feedback PMOS whose gate is \\(V_{\\rm out}\\).\n- If \\(V_{\\rm out}\\) rises, \\(M_2\\) supplies less current; the feedback adjusts the voltage at node \\(X\\) to keep the current through \\(M_1\\) approximately fixed.\n- Thus node \\(X\\) is a low-impedance current-input node, while \\(V_{\\rm out}\\) is the voltage-output node.\n\nEquivalently, with capacitance at \\(V_{\\rm out}\\), the same topology is a gyrator/CMOS active-inductor circuit.\n\n## 2. DC/large-signal behavior\nFor an unloaded output, the top current source forces the \\(M_1\\) drain current to \\(I_1\\):\n\\[\nI_{D1}=I_1.\n\\]\nThen\n\\[\nV_X=V_b-V_{Tn}-\\sqrt{\\frac{2I_1}{\\beta_n}},\n\\]\nwhere\n\\[\n\\beta_n=\\mu_n C_{ox}\\left(\\frac{W}{L}\\right)_1 .\n\\]\n\nKCL at node \\(X\\):\n\\[\nI_{D2}=I_B-I_1-I_{\\rm in}.\n\\]\nIf \\(M_2\\) is in saturation,\n\\[\n\\boxed{\nV_{\\rm out}\n=V_{DD}-|V_{Tp}|\n-\\sqrt{\\frac{2\\left(I_B-I_1-I_{\\rm in}\\right)}{\\beta_p}}\n}\n\\]\nwith\n\\[\n\\beta_p=\\mu_p C_{ox}\\left(\\frac{W}{L}\\right)_2 .\n\\]\n\nThus, to first order, a change in \\(I_{\\rm in}\\) changes the current in \\(M_2\\), and therefore changes \\(V_{\\rm out}\\).\n\n### Saturation requirements\nFor \\(M_1\\):\n\\[\nV_b-V_X>V_{Tn},\n\\qquad\nV_{\\rm out}\\ge V_b-V_{Tn}.\n\\]\nFor \\(M_2\\):\n\\[\nV_{\\rm out}<V_{DD}-|V_{Tp}|,\n\\qquad\nV_X\\le V_{\\rm out}+|V_{Tp}|.\n\\]\n\n## 3. Small-signal low-frequency response\nLet\n\\[\ng_{m2}=\\sqrt{2\\beta_p I_{D2,Q}},\n\\]\nwhere \\(I_{D2,Q}=I_B-I_1-I_{\\rm in,Q}\\).\n\nA small input current \\(i_{\\rm in}\\) (positive upward, as drawn) gives\n\\[\ni_{d2}=-i_{\\rm in}.\n\\]\nSince\n\\[\nv_{\\rm out}=-\\frac{i_{d2}}{g_{m2}},\n\\]\nwe obtain\n\\[\n\\boxed{\n\\frac{v_{\\rm out}}{i_{\\rm in}}\\approx \\frac{1}{g_{m2}}.\n}\n\\]\nSo the stage acts as a current-to-voltage converter with transresistance approximately \\(1/g_{m2}\\). If the defined input current is taken in the opposite direction, the sign reverses.\n\nThe input resistance at node \\(X\\) is very small because of the feedback:\n\\[\n\\boxed{\nR_{{\\rm in},X}\n\\approx\n\\frac{1}{g_{m2}\\left(1+g_{m1}r_{o1}\\right)}\n}\n\\]\nor, including body effect,\n\\[\nR_{{\\rm in},X}\\approx\n\\frac{1}{g_{m2}\\left[1+(g_{m1}+g_{mb1})r_{o1}\\right]}.\n\\]\nWith finite output resistances, add \\(1/r_{o2}\\) appropriately:\n\\[\nR_{{\\rm in},X}\n\\approx\n\\frac{1}{g_{m2}\\left[1+(g_{m1}+g_{mb1})r_{o1}\\right]+1/r_{o2}}.\n\\]\nIdeally, with \\(r_{o1}\\to\\infty\\), node \\(X\\) is a virtual ground for small signals.\n\nThe small-signal output resistance of the closed-loop voltage node is approximately\n\\[\n\\boxed{\nR_{{\\rm out}}\\approx \\frac{1}{g_{m2}}.\n}\n\\]\nSo \\(V_{\\rm out}\\) is a relatively low-impedance node.\n\n## 4. High-frequency behavior: active inductor\nIf the output terminal \\(V_{\\rm out}\\) has a total capacitance \\(C\\) to ground (including \\(C_{gs2}\\) and any external load), the input admittance at node \\(X\\) is approximately\n\\[\nY_{\\rm in}(s)\n\\approx\ng_{m1}\n+\n\\frac{g_{m1}g_{m2}}{sC}.\n\\]\nHence\n\\[\n\\boxed{\nZ_{\\rm in}(s)\n=\n\\frac{1}{Y_{\\rm in}(s)}\n\\approx\n\\frac{sC}{g_{m1}\\left(sC+g_{m2}\\right)}.\n}\n\\]\nFor frequencies well below \\(g_{m2}/C\\),\n\\[\n\\boxed{\nZ_{\\rm in}\\approx sL_{\\rm eq},\n\\qquad\nL_{\\rm eq}=\\frac{C}{g_{m1}g_{m2}}.\n}\n\\]\nIncluding body effect,\n\\[\n\\boxed{\nL_{\\rm eq}\\approx\\frac{C}{(g_{m1}+g_{mb1})g_{m2}}.\n}\n\\]\nEquivalently, the input node sees a simulated grounded inductor of value \\(L_{\\rm eq}\\) in parallel with a resistance of about \\(1/g_{m1}\\). Finite \\(r_{o1},r_{o2}\\) make the inductor lossy.\n\n## Summary\n- The circuit is a negative-feedback CMOS current-to-voltage/gyrator stage.\n- \\(M_1\\) is the common-gate/current-setting device; \\(M_2\\) is the feedback PMOS.\n- Low-frequency transresistance:\n  \\[\n  v_{\\rm out}/i_{\\rm in}\\approx 1/g_{m2}.\n  \\]\n- Input impedance at node \\(X\\) is very low:\n  \\[\n  R_{{\\rm in}}\\approx \\frac{1}{g_{m2}(1+g_{m1}r_{o1})}.\n  \\]\n- With capacitance at \\(V_{\\rm out}\\), the circuit behaves as a gyrator/active inductor with\n  \\[\n  L_{\\rm eq}\\approx \\frac{C}{g_{m1}g_{m2}}.\n  \\]\n- Proper operation requires \\(M_1\\) and \\(M_2\\) to remain saturated as given above.",
        "format": "markdown",
        "sha256": "807bd700c5dd56099336e2c6238c1a5f4a8fb9c3a08cbcccc5fb44674c8a9f77"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS input device and M2 as the PMOS feedback device driven by Vout, describes feedback to node X, and gives the very low input resistance and transimpedance of approximately 1/gm2. The additional active-inductor discussion is consistent with the topology.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 41464,
        "total_tokens": 42520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36439,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 41464,
        "total_tokens": 42520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36439,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Interpreting the rectangular two-terminal devices \\(M_1\\) and \\(M_2\\) as memristors, and letting \\(V_X\\equiv V_{\\rm out}\\) be the voltage at the center node:\n\n- \\(M_2\\) is connected between \\(V_{DD}\\) and \\(V_{\\rm out}\\).\n- \\(M_1\\) is connected between \\(V_{\\rm out}\\) and \\(V_b\\).\n- The current source \\(I_1\\) injects current into the \\(V_{\\rm out}\\) node.\n- Call the net current injected into that node by all lower current sources \\(I_{\\rm src}\\), positive into the node. For the drawn arrows,\n  \\[\n  I_{\\rm src}=I_1+I_{\\rm in}^{(\\uparrow)}-I_{\\rm sink}^{(\\downarrow)},\n  \\]\n  where the upward lower source is the labeled \\(I_{\\rm in}\\) and the downward source is its value if present. If the only active lower source is the labeled sink, use \\(I_{\\rm src}=I_1-I_{\\rm in}\\) instead.\n\nLet the instantaneous memristances be\n\\[\nR_1=R_{M1}(t),\\qquad R_2=R_{M2}(t).\n\\]\nThen KCL at \\(V_{\\rm out}\\) gives\n\\[\n\\frac{V_{\\rm out}-V_{DD}}{R_2}\n+\n\\frac{V_{\\rm out}-V_b}{R_1}\n=\nI_{\\rm src},\n\\]\nso\n\\[\n\\boxed{\nV_{\\rm out}\n=\n\\frac{R_1 V_{DD}+R_2 V_b+R_1R_2 I_{\\rm src}}\n{R_1+R_2}\n}\n\\]\nor, using conductances \\(G_1=1/R_1,\\;G_2=1/R_2\\),\n\\[\n\\boxed{\nV_{\\rm out}\n=\n\\frac{G_2 V_{DD}+G_1 V_b+I_{\\rm src}}\n{G_1+G_2}.\n}\n\\]\n\nThe currents through the memristors, positive in the directions \\(V_{DD}\\to V_{\\rm out}\\) and \\(V_{\\rm out}\\to V_b\\), are\n\\[\ni_{M2}=\\frac{V_{DD}-V_{\\rm out}}{R_2},\n\\qquad\ni_{M1}=\\frac{V_{\\rm out}-V_b}{R_1}.\n\\]\nThus\n\\[\ni_{M1}=i_{M2}+I_{\\rm src}.\n\\]\n\nFor the memristor state dynamics,\n\\[\n\\dot q_{M1}=\\pm i_{M1},\\qquad\n\\dot q_{M2}=\\pm i_{M2},\n\\]\n\\[\nR_{M1}=R_{M1}(q_{M1}),\\qquad\nR_{M2}=R_{M2}(q_{M2}),\n\\]\nwhere the sign depends on the polarity marked on each memristor. These equations together with the KCL expression determine \\(V_{\\rm out}\\) and the slow evolution of the memristances.\n\nImportant special cases:\n\n1. **No current injected, \\(I_{\\rm src}=0\\):**  \n   The circuit is simply a programmable memristive voltage divider:\n   \\[\n   \\boxed{\n   V_{\\rm out}\n   =\n   \\frac{R_1 V_{DD}+R_2 V_b}{R_1+R_2}\n   }\n   \\]\n   If \\(V_b=0\\),\n   \\[\n   V_{\\rm out}=\\frac{R_1}{R_1+R_2}V_{DD}.\n   \\]\n   Equal memristances give \\(V_{\\rm out}=(V_{DD}+V_b)/2\\).\n\n2. **Small-signal/read mode about fixed memristances:**  \n   The output node sees an equivalent Thevenin resistance\n   \\[\n   \\boxed{R_{\\rm th}=R_1\\parallel R_2=\\frac{R_1R_2}{R_1+R_2}}\n   \\]\n   and a current-to-voltage sensitivity\n   \\[\n   \\boxed{\\frac{\\partial V_{\\rm out}}{\\partial I_{\\rm src}}\n   =R_1\\parallel R_2.}\n   \\]\n   A positive injected current raises \\(V_{\\rm out}\\); a current drawn out of the node lowers it.\n\n3. **Programming state:**  \n   A nonzero \\(I_{\\rm src}\\) changes the currents through \\(M_1\\) and \\(M_2\\). If the resulting voltage/current exceeds the memristor threshold, the memristances change. The sign of the current through each device determines whether its memristance increases or decreases. The two devices are driven in complementary directions by an injected current at the center node, so this arrangement can be used as a programmable memristive voltage divider/memory element: the output voltage encodes the memristance ratio and is retained after the sources are removed, provided the memristors are below their switching threshold during readout.\n\nIf an external load \\(R_L\\) is connected from \\(V_{\\rm out}\\) to ground, simply add \\(1/R_L\\) to the denominator:\n\\[\nV_{\\rm out}\n=\n\\frac{G_2V_{DD}+G_1V_b+I_{\\rm src}}\n{G_1+G_2+1/R_L}.\n\\]\n\nIf the \\(M_1,M_2\\) symbols in your course are intended as MOSFETs rather than memristors, the same nodal/current-summing structure applies, but the linear conductance terms must be replaced by the appropriate MOSFET drain-current expressions.",
        "format": "markdown",
        "sha256": "f0ef2dd950e3b546781b63721f14666af9815920b6f1ab9f0c695e05fc1eb4ec"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the MOSFETs as memristors and analyzes a passive voltage divider, missing the common-gate NMOS, PMOS feedback path, and low-input-resistance current-feedback behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 30147,
        "total_tokens": 31203,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27662,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 30147,
        "total_tokens": 31203,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27662,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is an active-feedback current-to-voltage converter (a current sensor/buffer). Assuming the usual symbols: \\(M_2\\) is a PMOS with source at \\(V_{DD}\\), and \\(M_1\\) is an NMOS whose source is the internal node \\(X\\). The bottom unlabeled source is treated as a bias current \\(I_B\\).\n\n### 1. DC operating point\nFor no external load at \\(V_{\\rm out}\\),\n\\[\nI_{D1}=I_1\n\\]\nbecause the top current source and \\(M_1\\) are in series.\n\nFor \\(M_1\\) in saturation,\n\\[\nI_{D1}=\\frac12\\beta_n(V_b-V_X-V_{Tn})^2\n\\]\nso\n\\[\nV_X\\approx V_b-V_{Tn}-\\sqrt{\\frac{2I_1}{\\beta_n}},\n\\qquad \\beta_n=\\mu_n C_{ox}\\frac{W_1}{L_1}.\n\\]\nThus \\(V_X\\) is set mainly by \\(V_b\\) and \\(I_1\\); \\(M_1\\) holds the input node at a low incremental impedance.\n\nAt node \\(X\\), with \\(I_{\\rm in}\\) injected upward into \\(X\\) and the other source drawing \\(I_B\\) out of \\(X\\),\n\\[\nI_{D1}+I_{D2}=I_B-I_{\\rm in}\n\\]\nso\n\\[\nI_{D2}=I_B-I_{\\rm in}-I_1.\n\\]\nFor \\(M_2\\) in saturation,\n\\[\nI_{D2}=\\frac12\\beta_p\\big(V_{DD}-V_{\\rm out}-|V_{Tp}|\\big)^2,\n\\]\nhence\n\\[\n\\boxed{\nV_{\\rm out}\\approx\nV_{DD}-|V_{Tp}|-\n\\sqrt{\\frac{2\\left(I_B-I_{\\rm in}-I_1\\right)}{\\beta_p}}\n}\n\\]\nfor \\(I_B-I_{\\rm in}-I_1>0\\), where\n\\[\n\\beta_p=\\mu_p C_{ox}\\frac{W_2}{L_2}.\n\\]\nIf the input current is defined in the opposite direction, replace \\(I_{\\rm in}\\) by \\(-I_{\\rm in}\\). Thus the output has a square-root dependence on the input current. Increasing \\(I_{\\rm in}\\) (in the direction shown) reduces \\(M_2\\)'s current and raises \\(V_{\\rm out}\\).\n\n### 2. Saturation requirements\n- \\(M_1\\): \n\\[\nV_{\\rm out}\\ge V_b-V_{Tn}\n\\]\nand \\(V_b-V_X>V_{Tn}\\).\n- \\(M_2\\):\n\\[\nV_{\\rm out}<V_{DD}-|V_{Tp}|,\\qquad\nV_X\\le V_{\\rm out}+|V_{Tp}|.\n\\]\nIf \\(I_{\\rm in}\\) is too large, \\(M_2\\) cuts off; if too small, \\(M_2\\) can enter triode and the square-root expression is no longer valid.\n\n### 3. Small-signal behavior\nLet\n\\[\ng_{m1}=\\sqrt{2\\beta_n I_{D1}},\\qquad\ng_{m2}=\\sqrt{2\\beta_p I_{D2}},\n\\]\nand include body effect for \\(M_1\\) as \\(g_{m1}'=g_{m1}+g_{mb1}\\). The feedback loop \\(M_1\\)-\\(M_2\\) is negative feedback, so the input node is nearly a virtual ground and the output is a low-impedance voltage node.\n\nTo first order,\n\\[\n\\boxed{\\frac{v_{\\rm out}}{i_{\\rm in}}\\approx \\frac{1}{g_{m2}}}\n\\]\nfor a small current injected into \\(X\\), with the sign corresponding to the arrow shown. Also,\n\\[\n\\boxed{r_{\\rm in,X}\\approx \\frac{1}{(g_{m1}+g_{mb1})g_{m2}r_{o1}}}\n\\]\nwhich is a very small input resistance.\n\nThe output resistance is approximately\n\\[\n\\boxed{r_{\\rm out}\\approx \\frac{1}{g_{m2}} \\parallel r_{\\rm source}},\n\\]\nwhere \\(r_{\\rm source}\\) is the finite output resistance of the top current source (infinite for an ideal source). If the current is instead drawn out of the input node, the sign of the transfer is reversed.\n\n### 4. Function\nThis circuit accepts a current at a low-impedance node and produces a corresponding voltage at a relatively low-impedance output. \\(M_1\\) acts as a common-gate cascode/level shifter, while \\(M_2\\) provides shunt feedback and converts the current mismatch into \\(V_{\\rm out}\\). Therefore, it is effectively a current-to-voltage converter/current sensor with a nonlinear square-root large-signal characteristic and a linear small-signal transresistance of about \\(1/g_{m2}\\).",
        "format": "markdown",
        "sha256": "0608c05d6ac7d7be23c340a8387706f8d5f3a9f5db0739f99e7549a292d1cdb9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS input device and M2 as the PMOS feedback device, with feedback into node X. It gives the very low input resistance and the expected small-signal transresistance of approximately 1/gm2; its additional operating-point detail does not undermine the essential analysis.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 42828,
        "total_tokens": 43884,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41777,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1056,
        "output_tokens": 42828,
        "total_tokens": 43884,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41777,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No—there is no finite capacitance at which the ring oscillator suddenly stops oscillating, provided the inverters have enough small-signal gain.\n\nModel each inverter as a one-pole inverting stage:\n\\[\nH(s)=-\\frac{A_0}{1+sR_oC_L},\n\\]\nwhere \\(A_0\\) is its dc voltage gain and \\(R_o\\) its output resistance. The loop gain is\n\\[\nT(s)=H(s)^3.\n\\]\nOscillation requires \\(T(j\\omega)\\) to be positive real, i.e.\n\\[\n3(180^\\circ-\\tan^{-1}\\omega R_oC_L)=360^\\circ\n\\]\nso\n\\[\n\\tan^{-1}\\omega R_oC_L=60^\\circ,\n\\qquad\n\\omega_{\\rm osc}=\\frac{\\sqrt3}{R_oC_L}.\n\\]\nAt that frequency,\n\\[\n|T(j\\omega_{\\rm osc})|\n=\\frac{A_0^3}{(1+3)^{3/2}}\n=\\frac{A_0^3}{8},\n\\]\nwhich is independent of \\(C_L\\). Thus if \\(A_0>2\\), the circuit oscillates for every finite \\(C_L\\). Increasing the capacitors only lowers the oscillation frequency; the oscillator shifts to a lower frequency so that the capacitor impedances at the oscillation frequency remain finite and appropriate for the phase condition. The period grows roughly in proportion to \\(C_L\\).\n\nIn the strict mathematical limit \\(C_L\\to\\infty\\), \\(\\omega_{\\rm osc}\\to0\\) and the period/startup time tends to infinity. Thus an idealized circuit with literally infinite capacitance would have no finite-frequency, finite-time oscillation; in practice, leakage, finite drive current, and finite observation time can make a very large capacitance appear to prevent oscillation. But for any arbitrarily large but finite capacitance, the ideal circuit still oscillates.",
        "format": "markdown",
        "sha256": "efc35522a9b04f1c856cfe878adc9471f6c4bff9a9b2318a7b10446b837255fa"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the ring continues oscillating at a lower frequency for any finite, arbitrarily large capacitance, and supports this with the appropriate small-signal phase and gain analysis. The infinite-capacitance limit caveat does not undermine the answer.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1050,
        "output_tokens": 18964,
        "total_tokens": 20014,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18577,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1050,
        "output_tokens": 18964,
        "total_tokens": 20014,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18577,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No—assuming ideal or sufficiently high-gain inverters, making the three load capacitors arbitrarily large does **not** stop oscillation for any finite capacitance. It only lowers the oscillation frequency.\n\nFor a 3-inverter ring oscillator with each inverter modeled as a gain \\(-A\\) and output resistance \\(R\\) driving \\(C_L\\), the loop gain is\n\n\\[\nL(s)=\\left(\\frac{-A}{1+sRC_L}\\right)^3 .\n\\]\n\nOscillation occurs when \\(L(j\\omega)=1\\). The phase condition gives\n\n\\[\n3\\tan^{-1}(\\omega RC_L)=180^\\circ\n\\quad\\Rightarrow\\quad\n\\omega RC_L=\\sqrt{3},\n\\]\n\nso\n\n\\[\nf_{\\rm osc}=\\frac{\\sqrt{3}}{2\\pi R C_L}\\propto \\frac{1}{C_L}.\n\\]\n\nThe gain condition is independent of \\(C_L\\) (for this model): \\(A\\ge 2\\) (with some extra gain needed for startup). Thus increasing \\(C_L\\) simply makes the oscillation slower.\n\nAs \\(C_L\\to\\infty\\), \\(f_{\\rm osc}\\to 0\\). In the strict mathematical limit of infinite capacitance, the node voltages cannot change and there is no observable oscillation; also, in a real circuit leakage and finite gain can eventually prevent oscillation if \\(C_L\\) is absurdly large. But for any arbitrarily large finite capacitance, the ideal circuit still oscillates, only at an arbitrarily low frequency.",
        "format": "markdown",
        "sha256": "20d4a0bfe4cab9f70c5b2f0a3553f602c6fefe4c910a584898cd43152ef7fea2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that identical finite capacitors lower the oscillation frequency without stopping oscillation, and supports this with a valid small-signal phase and gain analysis. The caveats about the infinite-capacitance limit and real-circuit nonidealities do not undermine the stated ideal-model result.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1050,
        "output_tokens": 4968,
        "total_tokens": 6018,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1050,
        "output_tokens": 4968,
        "total_tokens": 6018,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**For any finite capacitance, no**—not if the inverters are otherwise ideal and have enough gain. Increasing the three load capacitors only slows the ring oscillator down. It does not remove the oscillation condition.\n\nWith a simple small-signal model, let each inverter have gain \\(-A\\) and output resistance \\(R\\). Then each stage is a low-pass stage\n\\[\n\\frac{V_i}{V_{i-1}}=-\\frac{A}{1+j\\omega R C_L}.\n\\]\nThe loop can start oscillating provided \\(A>2\\); increasing \\(C_L\\) only scales the pole positions and lowers the oscillation frequency, roughly as\n\\[\nf_{\\rm osc}\\sim \\frac{1}{R C_L}\n\\]\n(exact factor depends on thresholds/gain). Thus, as \\(C_L\\to\\infty\\), the period grows without bound and \\(f_{\\rm osc}\\to0\\). There is no finite critical capacitance at which oscillation suddenly stops, in this ideal model.\n\nIn the **strict mathematical limit** \\(C_L=\\infty\\) with ideal capacitors, the nodes cannot change voltage in finite time, so there is no finite-frequency oscillation. Also, in a perfectly balanced, noiseless circuit the ring can remain at the unstable all-midpoint state forever; any tiny noise/asymmetry starts it, though the startup time also grows with \\(C_L\\). In real circuits, leakage, finite input impedance, mismatch, and simulator/numerical issues can prevent startup or make the very-low-frequency oscillation difficult to observe.\n\nSo: **arbitrarily large but finite capacitors ⇒ it still oscillates, just arbitrarily slowly; exactly infinite capacitance ⇒ the period is infinite, i.e. no finite-frequency oscillation.**",
        "format": "markdown",
        "sha256": "d1d38a65ea88cf55ec2ed2e6648a4e9be568dc1413911159335182ba7082888f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that any finite, equal loading capacitance slows the ring without stopping oscillation, and supports this with a valid small-signal model and the A > 2 gain condition. The exact-infinite-capacitance caveat is consistent with the frequency tending to zero.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1051,
        "output_tokens": 12526,
        "total_tokens": 13577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12175,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1051,
        "output_tokens": 12526,
        "total_tokens": 13577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12175,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure is a three-stage ring oscillator. Doubling all three load capacitors doubles each stage delay, so the oscillation frequency is halved:\n\n\\[\nC_L\\to 2C_L \\quad\\Rightarrow\\quad f_0\\to \\frac{f_0}{2}.\n\\]\n\nFor a thermal-noise-limited ring oscillator in the usual \\(1/f^2\\) phase-noise region, assuming the same devices/bias and comparing at a fixed offset \\(\\Delta f\\),\n\n\\[\n\\mathcal L(\\Delta f)\\propto \\left(\\frac{f_0}{\\Delta f}\\right)^2.\n\\]\n\nTherefore,\n\n\\[\n\\frac{\\mathcal L_{\\text{new}}}{\\mathcal L_{\\text{old}}}\n=\\left(\\frac{1}{2}\\right)^2=\\frac14,\n\\]\n\nso the phase-noise power spectral density **decreases by about \\(10\\log_{10}4\\approx 6\\,\\mathrm{dB}\\)** at a given absolute offset frequency—i.e. the phase noise **improves by roughly 6 dB**.\n\nThe \\(1/f^3\\)/\\(1/f^2\\) corner frequencies and other frequency-dependent features also scale downward with \\(f_0\\). If compared at the same *normalized* offset \\(\\Delta f/f_0\\), the ideal phase-noise curve is essentially unchanged.",
        "format": "markdown",
        "sha256": "779b1b952c9b5493ea81ede8d7b0291ec1dd9054258781b9d2823bee41bef8b0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that doubling the capacitors halves the oscillation frequency and lowers phase noise by about 6 dB at a fixed offset; it also correctly notes the unchanged result at fixed normalized offset.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 21544,
        "total_tokens": 22592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19723,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 21544,
        "total_tokens": 22592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19723,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling the three load capacitors \\(C_L\\) halves the oscillation frequency (ideally \\(f_0 \\propto 1/C_L\\)). For thermal noise in the \\(1/f^2\\) phase-noise region, the ring-oscillator phase noise satisfies\n\n\\[\n\\mathcal L(\\Delta f)\\propto \\frac{f_0^2}{P_{\\rm DC}}\\frac{1}{\\Delta f^2}\n\\quad\\Rightarrow\\quad\n\\mathcal L(\\Delta f)\\propto \\frac{1}{C_L^2}\n\\]\n\nwith the same devices, bias, and output swing.\n\nTherefore, with \\(C_L\\to 2C_L\\),\n\n\\[\n\\mathcal L \\to \\frac{1}{4}\\mathcal L\n\\]\n\ni.e. the phase noise at a fixed offset decreases by about\n\n\\[\n10\\log_{10}(4)\\approx 6\\ \\text{dB}.\n\\]\n\nSo the phase noise improves by roughly **6 dB** (for the thermal-noise-limited case), while the oscillator runs at half the frequency. If the oscillator is re-tuned to keep the same frequency by increasing the current/gm, the improvement is different (roughly 3 dB for doubling the capacitance in that ideal comparison).",
        "format": "markdown",
        "sha256": "c15e69cedea2fff02d1ab94345ea4bab46ac185f4f1dd062c5bbef630d17fb77"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that doubling the capacitance halves the oscillation frequency, giving about a fourfold (6 dB) phase-noise reduction at a fixed offset. The retuning caveat is secondary to the question.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 33298,
        "total_tokens": 34346,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 33298,
        "total_tokens": 34346,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For a three-stage inverter ring oscillator like the one shown, doubling each load capacitor \\(C_L\\) doubles every stage time constant, so the oscillation frequency is approximately halved:\n\n\\[\nf_0' \\approx \\frac{f_0}{2}.\n\\]\n\nFor the usual thermal/white-noise-dominated ring-oscillator phase noise, at a fixed absolute offset \\(\\Delta f\\),\n\n\\[\n\\mathcal L(\\Delta f)\\propto \\frac{f_0^2}{Q^2\\Delta f^2},\n\\]\n\nand the open-loop \\(Q\\) of the three-stage ring is essentially unchanged when all capacitors are scaled together. Hence\n\n\\[\n\\mathcal L'(\\Delta f)\\approx \\frac14\\,\\mathcal L(\\Delta f),\n\\]\n\ni.e. the single-sideband phase noise decreases by\n\n\\[\n10\\log_{10}(4)\\approx 6.0\\ \\text{dB}.\n\\]\n\nSo, assuming the inverters are otherwise unchanged and thermal noise dominates, doubling all three \\(C_L\\)'s lowers the phase-noise power by a factor of 4, or **6 dB**, at a given absolute offset frequency. If one compares at the same *fractional* offset \\(\\Delta f/f_0\\), the normalized phase noise is essentially unchanged.",
        "format": "markdown",
        "sha256": "b77cdde70d9553261b7ba13ef306dbff88b4e362d4a2a4093781f081a1ac9edb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that doubling the capacitors approximately halves the oscillation frequency, giving a fourfold (6 dB) phase-noise reduction at a fixed absolute offset, and notes the fixed-relative-offset qualification.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 30011,
        "total_tokens": 31059,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1048,
        "output_tokens": 30011,
        "total_tokens": 31059,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the usual practical (finite-gain, finite-output-resistance) model: **yes, for sufficiently large \\(C_L\\) the circuit will stop oscillating.** There is a finite maximum load capacitance.\n\nThe large capacitor makes the pole at that node approximately\n\n\\[\n\\omega_p \\approx \\frac{1}{R_o(C_L+C_{\\rm in})},\n\\]\n\nwhich moves toward zero as \\(C_L\\to\\infty\\). Oscillation requires both the correct loop phase and loop gain \\(\\ge 1\\). At the frequency where the other inverter stages supply the remaining phase shift, the gain of the heavily loaded stage falls roughly as\n\n\\[\n|A_{\\rm loaded}|\\sim \\frac{1}{\\omega R_o C_L}\\to 0.\n\\]\n\nEventually the loop gain at the required phase is less than one, so the circuit cannot start or sustain oscillation; it settles to a dc operating point, typically near the inverter threshold.\n\nCaveat: if you use a completely idealized digital/delay-line model with infinite inverter gain and no finite output resistance, the ideal result is simply \\(f_{\\rm osc}\\to 0\\) as \\(C_L\\to\\infty\\). But a real ring oscillator with only one node heavily loaded will cease oscillating once the load exceeds a critical value; \\(C_L\\to\\infty\\) certainly means no finite-frequency oscillation.",
        "format": "markdown",
        "sha256": "f972860483ff3751a5984dcdb404a31883ef6e64730ebf0a61a5982978d6a44b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that sufficiently large one-sided loading causes a dominant pole and gain roll-off, violating the oscillation condition and potentially leaving the circuit at a DC operating point. The idealized-model caveat does not undermine the practical conclusion.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 18074,
        "total_tokens": 19142,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17801,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 18074,
        "total_tokens": 19142,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17801,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes—for a practical inverter circuit with finite gain and finite output resistance, it will eventually stop oscillating when \\(C_L\\) is made large enough.**  \n\nThe figure is a three-stage inverter ring oscillator with one interstage node loaded by \\(C_L\\). In a linearized model, each inverter contributes a pole. The loaded stage has transfer roughly\n\n\\[\n\\frac{-A_v}{1+j\\omega R_o C_L},\n\\]\n\nwhere \\(A_v\\) is the inverter low-frequency gain and \\(R_o\\) its output resistance. For oscillation, the loop must have \\(0^\\circ\\) total phase shift (mod \\(360^\\circ\\)) and loop gain at least unity. As \\(C_L\\) becomes very large, the phase condition can still be satisfied at a frequency set mainly by the other two inverter stages, but at that frequency the loaded stage’s gain falls as\n\n\\[\n\\left|\\frac{A_v}{1+j\\omega R_o C_L}\\right|\n\\approx \\frac{A_v}{\\omega R_o C_L}\\to 0.\n\\]\n\nThus the loop gain at the phase-crossover frequency tends to zero. For any finite inverter gain there is a maximum tolerable \\(C_L\\); beyond it the Barkhausen condition \\(|T(j\\omega)| \\ge 1\\) cannot be met, so the circuit fails to start—or fails to sustain—oscillation and settles to a stable dc operating point.\n\nFor the simplified case of equal unloaded node capacitance \\(C_i\\), the threshold condition can be written as\n\n\\[\nA_v^3 \\ge 2\\frac{(r+1)^2}{r},\n\\qquad r=\\frac{C_L}{C_i}.\n\\]\n\nAs \\(r\\to\\infty\\), the required \\(A_v\\to\\infty\\), so a finite-gain circuit must stop oscillating.\n\n**Caveat:** In an ideal mathematical model with infinite inverter gain and ideal voltage-source outputs, the conclusion can be model-dependent (the capacitor may only add delay, or the oscillation may tend to zero frequency). But for any real inverter, making \\(C_L\\) arbitrarily large will prevent oscillation.",
        "format": "markdown",
        "sha256": "7e64e00435613f92a4d1c363122dd8a231a4abfb4b4709556457fa6d80cd8098"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large loading on one node can stop oscillation and explains the dominant-pole gain loss at the phase-crossover frequency. The finite-gain/Barkhausen reasoning and dc-settling interpretation match the golden solution; the quantitative model is consistent with the same trend.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 24006,
        "total_tokens": 25074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23582,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 24006,
        "total_tokens": 25074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23582,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes—under the usual finite-gain/Barkhausen small-signal model, a sufficiently large \\(C_L\\) will prevent sustained oscillation.\n\nThe extra capacitance introduces a dominant pole in the feedback loop. The loop must simultaneously satisfy the phase condition (the three inversions plus the stage poles must give \\(0^\\circ\\) loop phase) and have loop gain \\(\\ge 1\\). As \\(C_L\\to\\infty\\), the pole due to that node moves toward zero frequency; at the frequency needed for the other stages to supply the remaining phase shift, that capacitor looks nearly like an ac ground and heavily attenuates the signal. The loop-gain magnitude falls below unity, so oscillation dies out. Equivalently, an infinite capacitance would freeze that node, breaking the ring.\n\nFor finite but not too large \\(C_L\\), the circuit may still oscillate—just at a lower frequency. There is a maximum tolerable \\(C_L\\) beyond which oscillation ceases. In an idealized model with infinite gain and no other dynamics one may describe the limit as frequency tending to zero, but that is a degenerate limit and not a sustained practical oscillation.",
        "format": "markdown",
        "sha256": "1e4f7e0a4e0ef7f12bc42bd29e9ae4da48f57b3a504fae708a991cadfb09a022"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that sufficiently large one-node capacitance creates a dominant pole, unbalances the loop, and drives loop gain below unity so oscillation stops. The added frequency-limit caveat does not undermine the essential answer.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 28065,
        "total_tokens": 29133,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30987,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1068,
        "output_tokens": 28065,
        "total_tokens": 29133,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30987,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**It improves (decreases) by about \\(3\\ \\mathrm{dB}\\)**, assuming an ideal, unloaded CMOS ring oscillator and thermal-noise–limited operation.\n\nDoubling both device widths roughly doubles:\n\n- drive current \\(I_D\\) and \\(g_m\\),\n- node capacitance \\(C\\) (gate/drain parasitics),\n- dc power dissipation,\n\nso the oscillation frequency remains approximately unchanged:\n\\[\nf_{\\rm osc}\\sim \\frac{I_D}{C V_{DD}}\\; \\xrightarrow{W\\to 2W}\\; \\text{about the same.}\n\\]\n\nThe thermal current-noise PSD of each MOSFET is proportional to \\(g_m\\), while the effective node impedance falls as \\(1/g_m\\) (or, equivalently, the stored/oscillating energy grows with \\(C\\)). The resulting phase-noise spectral density scales as\n\\[\n\\mathcal L(\\Delta f)\\propto \\frac{\\sum 4kT\\gamma g_m}{C^2}\\propto \\frac{W}{W^2}=\\frac{1}{W}.\n\\]\nThus doubling \\(W\\) halves the phase-noise power:\n\\[\n\\Delta \\mathcal L = 10\\log_{10}\\!\\left(\\frac12\\right)\\approx -3\\ \\mathrm{dB}.\n\\]\n\nSo the single-sideband phase noise at a given offset becomes about **3 dB lower**; the rms phase jitter decreases by roughly a factor of \\(\\sqrt{2}\\). Exact results can differ if fixed external load capacitance, constant-current biasing, short-channel effects, or flicker noise dominate.",
        "format": "markdown",
        "sha256": "407c98ee9580e14ae0daf9fd93ad63dd31555f9c2f0007d969fc0977f94c3d7a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly predicts about a 3 dB phase-noise reduction and gives a consistent width-scaling explanation: device noise and capacitance increase, while the resulting signal-to-noise ratio improves by a factor of two.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 17716,
        "total_tokens": 18732,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16984,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 17716,
        "total_tokens": 18732,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16984,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling both the NMOS and PMOS widths in this three-stage CMOS ring oscillator ideally causes:\n\n- The device currents/transconductances and node capacitances to both roughly double, so the oscillation frequency and voltage swing remain about the same.\n- The thermal phase-noise power spectral density scales approximately as  \n  \\[\n  \\mathcal L(\\Delta f)\\propto \\frac{g_m}{C^2}\\propto \\frac{1}{W}\n  \\]\n  for fixed frequency and bias conditions.\n\nTherefore, with \\(W\\to 2W\\),\n\\[\n\\mathcal L_{2W}(\\Delta f)\\approx \\frac{1}{2}\\mathcal L_{W}(\\Delta f),\n\\]\nso the phase noise decreases by about\n\n\\[\n10\\log_{10}(2)\\approx 3\\ \\text{dB}\n\\]\n\n(equivalently, phase-noise PSD halves and rms phase jitter over a fixed bandwidth drops by \\(\\sqrt2\\)). The dc current/power roughly doubles. Fixed parasitic capacitance, short-channel effects, or a fixed external bias current can make the actual improvement differ.",
        "format": "markdown",
        "sha256": "4630b3e4fff835e4e7172ef7ca2686f5c233c66c30827d5d600934e7e2e80ea3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly predicts about a 3 dB phase-noise reduction and gives a consistent width-scaling explanation: device noise current power and transconductance scale with width, while node capacitance doubles, reducing noise voltage/phase-noise PSD by a factor of two. The power and jitter comments are also consistent.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 14529,
        "total_tokens": 15545,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14302,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 14529,
        "total_tokens": 15545,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14302,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling both \\(W_n\\) and \\(W_p\\) increases the drive current and the transconductance by about \\(2\\times\\), but it also doubles the device/gate capacitance at each node. Thus, to first order, the ring oscillator’s frequency stays about the same because\n\\[\nt_d \\sim \\frac{C V_{DD}}{I_D}, \\qquad C\\propto W,\\; I_D\\propto W.\n\\]\n\nThe thermal noise voltage referred to the switching node scales as\n\\[\n\\overline{v_n^2}\\sim \\frac{kT}{C}\\propto \\frac{1}{W},\n\\]\nso the phase-noise power spectral density decreases by roughly a factor of 2. Therefore,\n\\[\n\\Delta \\mathcal L(\\Delta f) \\approx 10\\log_{10}(1/2)\\approx -3\\ \\text{dB}.\n\\]\n\n**Answer: The phase noise improves—decreases by about \\(3\\,\\text{dB}\\)—assuming ideal first-order scaling and that the oscillation frequency is approximately unchanged. The power dissipation roughly doubles. In real short-channel devices, fixed parasitics and flicker-noise effects can make the exact improvement differ.**",
        "format": "markdown",
        "sha256": "1f727d94e6639ff1ebf3f7732b3059e3656a4690fe16172ea778ea7c74eec4c3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly predicts about a 3 dB phase-noise reduction and gives the valid capacitance-scaling justification; the frequency and power comments are consistent with the golden solution.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 12933,
        "total_tokens": 13949,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12689,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1016,
        "output_tokens": 12933,
        "total_tokens": 13949,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12689,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For a small-signal perturbation at the common supply rail, the three identical inverters respond in the same way, so all three input/output nodes move together. Thus, for the common-mode supply signal, each inverter behaves as if its input were tied to its output: a diode-connected PMOS in series with a diode-connected NMOS. The supply sees three such branches in parallel.\n\nFor one inverter, with PMOS/NMOS small-signal transconductances \\(g_{mp},g_{mn}\\) and output conductances \\(g_{dsp}=1/r_{op}\\), \\(g_{dsn}=1/r_{on}\\), its equivalent resistance is\n\\[\nR_{\\text{inv}}\n=\n\\frac{1}{g_{mp}+g_{dsp}}\n+\n\\frac{1}{g_{mn}+g_{dsn}}.\n\\]\nThree equal inverters in parallel give\n\\[\n\\boxed{\nR_X\n=\n\\frac{1}{3}\\left[\n\\frac{1}{g_{mp}+g_{dsp}}\n+\n\\frac{1}{g_{mn}+g_{dsn}}\n\\right]\n}\n\\]\nwith the usual convention that the test current enters the supply node.\n\nIf channel-length modulation is neglected and the two devices of each inverter are matched, \\(g_{mp}=g_{mn}=g_m\\),\n\\[\n\\boxed{\nR_X=\\frac{1}{3}\\left(\\frac1{g_m}+\\frac1{g_m}\\right)\n=\\frac{2}{3g_m}.\n}\n\\]\nThis low-frequency small-signal resistance is positive for the ideal symmetric ring; the sign would reverse only if one defines the current as leaving the supply node.",
        "format": "markdown",
        "sha256": "c1a19a60e129d19804e27d19845a8631b2bb72085d4ab402c1fb12387313b630"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based resistance from a diode-connected-inverter model, but misses the dominant oscillation-driven charging and discharging of the load capacitances. The expected resistance is approximately 1/(3f0CL), with possible refinement for f0's supply dependence.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 28442,
        "total_tokens": 29454,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28097,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 28442,
        "total_tokens": 29454,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28097,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For a low-frequency small-signal analysis, assume the three identical CMOS inverters are matched and biased in their high-gain region. Let each pMOS/nMOS have small-signal transconductance \\(g_m\\) and output conductance \\(g_{ds}=1/r_o\\).\n\nApply a test voltage \\(v_x\\) at the common supply node. By symmetry, all three inverter output/input nodes shift together; KCL gives\n\\[\nv_o=\\frac{v_x}{2}.\n\\]\nThe supply current drawn by one inverter is\n\\[\ni=(g_m+g_{ds})(v_x-v_o)\n =\\frac{g_m+g_{ds}}{2}v_x.\n\\]\nWith three inverters,\n\\[\nI_x=3i=\\frac{3}{2}(g_m+g_{ds})v_x.\n\\]\nHence\n\\[\n\\boxed{R_X=\\frac{v_x}{I_x}\n =\\frac{2}{3(g_m+g_{ds})}}\n\\]\nor, neglecting channel-length modulation/output resistance,\n\\[\n\\boxed{R_X\\approx \\frac{2}{3g_m}}.\n\\]\n\nIf \\(G_m=g_{mn}+g_{mp}\\) denotes the total transconductance of one symmetric inverter, this is equivalently\n\\[\nR_X\\approx \\frac{4}{3G_m}.\n\\]\n\nThe resistance is positive for the low-frequency common-mode supply port. At higher frequencies, capacitances must be included and \\(R_X\\) becomes a frequency-dependent impedance.",
        "format": "markdown",
        "sha256": "3575ac4a8b1aa7bb9749714d8c2e3bf592a78a4bc76efe5646c683ce4ada3adc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based resistance and ignores the dominant oscillation-driven charging and discharging of the node capacitances. The golden solution specifically assigns this kind of internally consistent static analysis a score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 38203,
        "total_tokens": 39215,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 37891,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 38203,
        "total_tokens": 39215,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 37891,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assume each inverter is a CMOS inverter biased in its small-signal (linear) region. By symmetry, a small test voltage \\(v_x\\) applied at the common supply node shifts all three internal inverter nodes by the same small-signal voltage. Hence, for each inverter the small-signal input and output voltages are effectively equal, so its PMOS and NMOS devices look like two diode-connected MOSFETs in series between the supply node and ground.\n\nUsing \\(g_{mN},g_{mP}\\) for the device transconductances and \\(g_{dsN},g_{dsP}\\) for their output conductances, one inverter branch has resistance\n\\[\nR_{\\rm branch}\n=\n\\frac{1}{g_{mP}+g_{dsP}}\n+\n\\frac{1}{g_{mN}+g_{dsN}}.\n\\]\nThe three inverters are in parallel at the supply node, so\n\\[\n\\boxed{\nR_X\n=\n\\frac{1}{3}\\left[\n\\frac{1}{g_{mP}+g_{dsP}}\n+\n\\frac{1}{g_{mN}+g_{dsN}}\n\\right]\n=\n\\frac{g_{mN}+g_{mP}+g_{dsN}+g_{dsP}}\n{3(g_{mP}+g_{dsP})(g_{mN}+g_{dsN})}\n}\n\\]\nThis is a positive resistance for a symmetric ring linearized about its quiescent point.\n\nFor the usual symmetric case \\(g_{mN}=g_{mP}=g_m\\) and\n\\(g_{dsN}=g_{dsP}=g_{ds}\\),\n\\[\n\\boxed{\nR_X=\\frac{2}{3(g_m+g_{ds})}\n\\approx \\frac{2}{3g_m}\n\\quad (g_{ds}\\ll g_m)\n}\n\\]\nIf the inverter transconductance is instead quoted as the total transconductance\n\\(G_m=g_{mN}+g_{mP}\\), then for symmetric devices the approximate result is\n\\[\n\\boxed{R_X\\approx \\frac{4}{3G_m}}.\n\\]\n\nFor ideal logic inverters with no dc conduction at the operating point, the small-signal resistance would instead be infinite; the finite result above applies when both devices are on, as in the linearized mid-rail operating point of a CMOS ring oscillator.",
        "format": "markdown",
        "sha256": "0604db48538c510a2b5433087f31f324a4324265a72090dfa44d9cb42d358b44"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based resistance and ignores the oscillation-driven charging and discharging of the load capacitances, which sets the resistance in the question. The static derivation is internally consistent enough for the rubric’s specified score of 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 28925,
        "total_tokens": 29937,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1012,
        "output_tokens": 28925,
        "total_tokens": 29937,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "There is no single \\(R_X\\) for a ring oscillator that is actually running. The expression\n\\[\nR_X \\simeq \\frac13\\left(\\frac1{g_{mn}}+\\frac1{g_{mp}}\\right)\n\\]\nis only a low-frequency, small-signal **quiescent** estimate about the balanced operating point where all three inverters are held at their switching threshold, with \\(r_o\\), capacitances, body effect, etc. neglected. The “two diode-connected devices in series” explanation is misleading: the MOS gates are not tied to their own drains in a ring oscillator. The result can be recovered in an ideal analysis because a common supply perturbation shifts the stages together, but that is not equivalent to each inverter being locally diode-connected.\n\nFor a circuit that is oscillating:\n\n- The balanced dc point is unstable and is not the operating point. A real oscillator settles into a large-signal periodic orbit.\n- The transistors switch between cutoff, saturation, and triode; \\(g_m\\) and the supply current are periodic functions of time, \\(g_m(t)\\), \\(i_{DD}(t)\\).\n- A small disturbance at the supply sees a periodically time-varying (LPTV) circuit, not a fixed resistor. A sinusoidal perturbation produces sidebands at \\(\\omega \\pm n\\omega_{\\rm osc}\\).\n- Therefore, in general, the supply presents a complex, frequency-dependent admittance, and possibly gain/negative real parts at some sidebands. At best one can define a low-frequency averaged effective conductance,\n  \\[\n  G_{X,\\text{eff}}=\\overline{\\frac{\\partial i_{DD}}{\\partial V_{DD}}}\n  \\]\n  over one oscillation period, or a full LPTV admittance \\(Y_X(\\Omega)\\). These depend on oscillation amplitude, waveform, load capacitance, short-circuit current, frequency, etc., and are generally not the quiescent \\(1/R_X\\) above.\n\nEven within the idealized small-signal model about the threshold point, \\(R_X\\) is not a constant unless one takes the dc limit. For example, neglecting \\(r_o\\) but including a capacitance \\(C\\) at each output,\n\\[\nY_X(s)\\approx 3g_{mp}\\frac{sC+g_{mn}}{sC+g_{mp}+g_{mn}},\n\\]\nso only at \\(s=0\\) do you get\n\\[\nY_X(0)=\\frac{3g_{mp}g_{mn}}{g_{mp}+g_{mn}},\n\\qquad\nR_X(0)=\\frac13\\left(\\frac1{g_{mn}}+\\frac1{g_{mp}}\\right).\n\\]\nAt nonzero frequency the impedance is complex; during oscillation the model must be further linearized about the periodic switching waveform.\n\nSo: if you literally mean the small-signal derivative about the *same exact dc equilibrium*, that limit is still given by the formula (subject to its approximations), although the equilibrium is unstable. But for the actual oscillating circuit, the answer changes: there is no constant \\(R_X\\), and the quoted value is not the effective supply resistance of the running oscillator.",
        "format": "markdown",
        "sha256": "bc2f347078b20c6852f6e9f8f64493ce27f8828064f375362ecfd180d37cef1b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer focuses on the time-varying small-signal model and says the running oscillator has no effective scalar resistance. It misses the expected average capacitive-charging mechanism and the key conclusion that the resulting resistance remains on the order of the MOS on-resistance, not much higher than the static estimate.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 27282,
        "total_tokens": 28374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27857,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 27282,
        "total_tokens": 28374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27857,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The quoted expression is **not a general “resistance of the oscillating ring oscillator.”** It is only the low-frequency small-signal equivalent resistance at a specified dc operating point, in the common-mode sense, and with the usual approximation \\(g_m\\gg g_{ds}\\).\n\nA few points:\n\n1. **If the circuit is actually oscillating**, it has no stable dc operating point. The bias is periodic; the transistor \\(g_m\\)’s vary over the oscillation cycle. A small perturbation at the supply can be frequency-converted (sidebands) and can have a phase-dependent, complex, even negative real part at some frequencies. Therefore, in steady oscillation there is no single time-independent \\(R_X\\) as sketched. A periodic small-signal / harmonic-balance analysis is needed.\n\n2. **If you only linearize about the ideal balanced point** (all three nodes at the same dc voltage), the local common-mode value is approximately\n   \\[\n   R_X(0)\\approx\n   \\frac{1}{3}\\left[\n   \\frac{1}{g_{mn}+g_{dsn}}\n   +\\frac{1}{g_{mp}+g_{dsp}}\n   \\right],\n   \\]\n   which reduces to the quoted result when \\(g_{ds}\\ll g_m\\). This value is the differential resistance of the common-mode network at that bias point. The fact that the loop is capable of oscillating does not, by itself, add a negative-resistance term to this common-mode port in a perfectly symmetric linear model; the oscillatory mode is a phase-sequenced loop mode, while a supply perturbation is common-mode.\n\n3. **For an actual large-signal oscillating CMOS ring**, the devices switch. During much of the cycle one transistor is off and \\(g_m\\approx0\\), while during transitions both devices may conduct. Thus the average/effective supply resistance is set by the switching current, delay/frequency variation with \\(V_{DD}\\), and short-circuit current—not by the mid-bias \\(g_m\\) formula. At low frequency, the observable quantity is the derivative of the average supply current,\n   \\[\n   R_{X,\\rm eff}^{-1} = \\frac{dI_{DD,\\rm avg}}{dV_{DD}},\n   \\]\n   not simply the diode-connected \\(g_m\\) expression.\n\nSo: **at the unstable dc bias point, the formula can still be written as a small-signal linearization; but for a real oscillating circuit, the answer changes—there is no single \\(R_X\\), and the simple diode-connected approximation is no longer valid.**",
        "format": "markdown",
        "sha256": "67461bb447f8c49f8e8cb294e3029a689d4443aa9775bb441b4f9d24f8f43692"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer focuses on the lack of a fixed DC operating point and says the resistance changes, but misses the key result: oscillatory supply current is set mainly by charging and discharging node capacitances, leaving the effective resistance on the order of the MOS on-resistance rather than much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 34061,
        "total_tokens": 35153,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33521,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 34061,
        "total_tokens": 35153,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 33521,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The quoted expression is a **low-frequency small-signal result about a fixed quiescent operating point**, not a general result for an oscillating ring.\n\nAt a common-mode small-signal change \\(v_x\\) on \\(V_{DD}\\), the currents in the NMOS and PMOS of each inverter must balance to first order at its output. Thus each stage presents an effective conductance\n\\[\ng_{\\text{stage}}=\\frac{g_{mn}g_{mp}}{g_{mn}+g_{mp}},\n\\]\nand the three stages in parallel give\n\\[\nG_X=3\\,g_{\\text{stage}},\\qquad\nR_X=\\frac1{G_X}=\\frac13\\left(\\frac1{g_{mn}}+\\frac1{g_{mp}}\\right).\n\\]\nEquivalently, each inverter *looks* diode-connected because, for this common-mode supply perturbation, the gate and drain small-signal voltages of the devices in an inverter move together. It does not mean the ring is actually gate-to-drain shorted.\n\nSo:\n\n- **If the circuit is not oscillating**, or if you are asking for the local small-signal/Jacobian value at the unstable bias used for start-up, the expression is the usual approximation. The fact that the loop itself may have a right-half-plane pole does not by itself change that local Jacobian.\n\n- **If the circuit is actually oscillating in steady state**, the situation changes. There is no fixed dc operating point. The transistor transconductances become periodic functions of time,\n  \\[\n  g_{mn}=g_{mn}(t),\\qquad g_{mp}=g_{mp}(t),\n  \\]\n  and devices spend part of the cycle in cutoff/triode rather than sitting in saturation at a bias point. A small perturbation at the supply is no longer described by a single real resistor; it is described by a periodically time-varying linear system. A sinusoidal test at frequency \\(\\omega\\) produces components at \\(\\omega\\pm n\\omega_{\\rm osc}\\), and near \\(\\omega_{\\rm osc}\\) the oscillator can be pulled/injection-locked. Thus the supply port has a frequency-dependent, generally complex admittance; it may look active near certain frequencies, and “\\(R_X\\)” is not a unique positive number.\n\nIf one wants an averaged dc resistance during oscillation, one must compute\n\\[\nR_{X,\\text{avg}}=\n\\left(\\frac{d\\langle I_{VDD}\\rangle}{dV_{DD}}\\right)^{-1}\n\\]\nover one complete oscillation period, including the change in oscillation frequency and the dynamic capacitor-charging current. For a rail-to-rail switching CMOS ring this is dominated by dynamic charging current, short-circuit current, and the fraction of time the devices conduct; it is generally not the above class-A diode-connected result.\n\nFor illustration, in a very simplified linear model with identical stages, capacitance \\(C\\) at each output, and only common-mode excitation,\n\\[\nY_X(j\\omega)\\approx\n3g_{mp}\\frac{g_{mn}+j\\omega C}{g_{mn}+g_{mp}+j\\omega C},\n\\]\nso\n\\[\nR_X(0)=\\frac13\\left(\\frac1{g_{mn}}+\\frac1{g_{mp}}\\right),\n\\]\nbut at the oscillator’s actual frequency the impedance is different. This simple formula does not include the nonlinear limit cycle.\n\n**Bottom line:** The formula is valid only as a low-frequency/quasi-static small-signal equivalent at a fixed bias (or for an infinitesimal oscillation). In a real oscillating ring oscillator, yes—the effective supply resistance/impedance changes: use periodic small-signal analysis or harmonic-balance/time-domain simulation; a single \\(R_X\\) is not sufficient.",
        "format": "markdown",
        "sha256": "d42e8a87470e749e5e40ed16ca068bfb90972dcbde1e21af69dc04dd6f9962f4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes dynamic capacitor charging, but does not derive the average resistance or show that it remains on the order of the MOS on-resistance. Instead it concludes that the effective resistance changes and that no single value applies, missing the key result.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 29582,
        "total_tokens": 30674,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28817,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1092,
        "output_tokens": 29582,
        "total_tokens": 30674,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28817,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To first order, the initial small-signal voltage gain of this regenerative comparator is approximately\n\n\\[\nA_{v0}\\approx \\frac{g_{m1,2}}{g_{m3,4}+g_{m5,6}}\n\\]\n\n(up to finite-output-resistance effects). Increasing the width of \\(M_7\\) increases the tail current \\(I_{SS}\\). In saturation, \\(g_m\\propto\\sqrt{I_D}\\), so the transconductances of the input pair and of the cross-coupled latch devices both increase roughly by the same factor.\n\nTherefore, the **initial voltage gain remains approximately constant** as \\(W_7\\) is increased; what increases is mainly the bias current, speed, and power dissipation. If \\(M_7\\) becomes so wide that devices leave saturation, headroom is reduced, or short-channel effects dominate, the gain may decrease somewhat in practice.",
        "format": "markdown",
        "sha256": "139e08e4e480774e06948f152cef69554f295e9aac78e3160f65254207cea1ed"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer identifies that a wider M7 raises tail current, but incorrectly concludes the initial gain stays constant. The essential trend is that gain decreases because gm grows more slowly than the tail current.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1055,
        "output_tokens": 29621,
        "total_tokens": 30676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 29438,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1055,
        "output_tokens": 29621,
        "total_tokens": 30676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 29438,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To first order, the **initial voltage gain remains essentially unchanged** as \\(W_7\\) is increased.\n\nThe tail transistor \\(M_7\\) sets the bias current. Increasing its width raises \\(I_{\\text{tail}}\\) and therefore increases the transconductances of the input devices and the cross-coupled latch devices. During the initial pre-regeneration phase the small-signal gain is set mainly by a transconductance ratio, approximately\n\n\\[\nA_{v0}\\sim \\frac{g_{m1,2}}{g_{m,\\text{latch}}}\n\\]\n\n(up to the sign/effective latch transconductance). In saturation, \\(g_m\\propto \\sqrt{I_D}\\), so the \\(\\sqrt{I_{\\text{tail}}}\\) factor cancels in the ratio.\n\nThus:\n\n- Ideally: \\(A_{v0}\\) is **independent of \\(W_7\\)** for fixed device dimensions of \\(M_1\\)–\\(M_6\\) and all devices staying in saturation.\n- Increasing \\(W_7\\) mainly increases the bias current, improving speed/regeneration and possibly changing offset/noise.\n- In real short-channel devices, if \\(W_7\\) is made too large and velocity saturation, channel-length modulation, or loss of saturation occurs, the initial gain usually **decreases slightly** rather than increasing.\n\nSo the expected ideal answer is: **the initial voltage gain stays approximately constant.**",
        "format": "markdown",
        "sha256": "0e4f8c2f6b2fd1c55597d2518331e57a3e1e81f8b69e5d559c899c272264fe54"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives the wrong trend: the initial gain decreases as M7 widens. Although it notes that tail current and transconductance rise, its proposed input-to-latch transconductance cancellation misses the relevant gain dependence on tail current.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1055,
        "output_tokens": 30503,
        "total_tokens": 31558,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30213,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1055,
        "output_tokens": 30503,
        "total_tokens": 31558,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 30213,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Assuming all devices remain in saturation and we use the usual square-law model, the **initial voltage gain stays approximately constant**—it is not changed (to first order) by increasing the width of \\(M_7\\).\n\nBefore regenerative action, the small-signal gain is set by a ratio of transconductances, e.g.\n\n\\[\nA_{v,\\text{init}} \\approx \\frac{g_{m1,2}}{g_{m3,4}}\n\\]\n\nor, when both cross-coupled NMOS/PMOS latch devices are considered,\n\n\\[\nA_{v,\\text{init}} \\approx \\frac{g_{m1,2}}{g_{m3,4}+g_{m5,6}}.\n\\]\n\nIncreasing \\(W_7\\) increases the tail current and hence increases all \\(g_m\\)'s. Since for a saturated MOS\n\n\\[\ng_m \\propto \\sqrt{\\mu C_{ox}\\frac{W}{L}I_D},\n\\]\n\nthe increase in current raises the numerator and denominator in the same way, so the ratio cancels.\n\nSo:\n\n- **Initial small-signal voltage gain:** approximately unchanged with larger \\(W_7\\).\n- **Main effect of increasing \\(W_7\\):** larger tail current, faster regeneration/shorter latch time constant, and better speed—at the cost of power/headroom.\n- In a real short-channel process, or if devices leave saturation, the gain may decrease somewhat because of finite output resistance and mobility degradation.",
        "format": "markdown",
        "sha256": "96065b25602e2acfe75d730134c881a566a5457635bbe7165b89a13b2d4737be"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that a wider M7 increases tail current, but the conclusion that initial gain stays constant relies on an invalid cancellation argument. The gain decreases as tail current rises, so the answer misses the essential trend.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1055,
        "output_tokens": 34578,
        "total_tokens": 35633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34271,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1055,
        "output_tokens": 34578,
        "total_tokens": 35633,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34271,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the capacitance at nodes \\(P\\) and \\(Q\\) **reduces the initial (pre-regeneration) voltage gain** and increases the comparison delay.\n\nThese nodes are high-impedance internal nodes. A larger \\(C_P,C_Q\\) increases the time constant for their voltages to change, so for the same input difference and clock-evaluation time, a smaller differential voltage is developed before the cross-coupled latch begins to regenerate. In the short-time limit the output difference grows roughly as\n\n\\[\n\\Delta V_{XY}(t)\\propto \\frac{g_{m1}g_{m3}}{C_X C_P}\\,\\Delta V_{\\rm in}\\,t^2\n\\]\n\nfor symmetric capacitors, so the initial gain varies roughly inversely with the capacitance at \\(P,Q\\).\n\nThe eventual/static transconductance-limited gain is mainly set by device \\(g_m\\) ratios, but in a dynamic comparator the **effective initial gain** becomes smaller; if the capacitance is too large, small input differences may not be resolved within the allotted clock period.",
        "format": "markdown",
        "sha256": "7cdab6579d20526ac546f10c689e3ebc139724598686f4571af5b4a596f15914"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that larger capacitance slows the transient and increases delay, but incorrectly concludes that initial gain decreases. The longer amplification interval compensates for the slower differential-voltage buildup, leaving the initial gain essentially unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 27403,
        "total_tokens": 28457,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27189,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 27403,
        "total_tokens": 28457,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27189,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the capacitance at nodes **P and Q** slows the discharge/charging of those internal nodes. During the initial, pre-regeneration phase, the same differential current from \\(M_1/M_2\\) produces a smaller voltage change on the larger capacitance, so the initial differential voltage delivered to the latch is reduced. Equivalently, the early-time gain behaves roughly as\n\n\\[\nv_{PQ}(t)\\sim \\frac{g_{m1,2}}{C_{P,Q}}\\,v_{id}\\,t,\n\\]\n\nor, including the latch loading,\n\n\\[\nv_{PQ}\\approx \\frac{g_{m1,2}}{g_{m3,4}}\n\\left(1-e^{-t/\\tau_{P,Q}}\\right)v_{id},\n\\qquad\n\\tau_{P,Q}\\approx \\frac{C_{P,Q}}{g_{m3,4}} .\n\\]\n\nThus, for a given comparison time, the **initial/effective voltage gain decreases** and the regeneration/delay time increases. If the comparator were allowed to settle indefinitely, the final small-signal gain set by transistor \\(g_m\\) ratios would be largely independent of the capacitance, but in a clocked comparator the larger capacitance degrades the gain available in the initial phase.",
        "format": "markdown",
        "sha256": "dc82b52a9a1baced9bb942626a549b4fccb90c0f2e4e207e15ae850a6f280acc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer correctly notes that larger capacitance slows the node-voltage change, but concludes that the initial gain decreases. It misses that the amplification phase lasts proportionally longer, so the capacitance cancels and the initial gain remains approximately unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 34760,
        "total_tokens": 35814,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34506,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 34760,
        "total_tokens": 35814,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34506,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the capacitance at nodes \\(P\\) and \\(Q\\) reduces the initial (pre-regeneration) voltage gain.\n\nDuring the first phase, the input pair \\(M_{1,2}\\) converts the differential input into a current that charges/discharges the capacitance at \\(P,Q\\):\n\n\\[\n\\Delta V_{P,Q}\\approx \\frac{g_{m1,2}\\,V_{\\rm in}}{sC_{P,Q}}\n\\quad\\text{or, in the time domain,}\\quad\n\\Delta V_{P,Q}(t)\\approx \\frac{g_{m1,2}V_{\\rm in}}{C_{P,Q}}\\,t\n\\]\n\nfor a short initial time.  Thus, for the same input and same observation time, a larger \\(C_P=C_Q\\) produces a smaller differential voltage at \\(P,Q\\).  That reduced voltage drives the cross-coupled pair \\(M_{3,4}\\), so the early differential output voltage is also smaller; the initial gain falls roughly as \\(1/C_{P,Q}\\) (or as a lower bandwidth/time constant).  The comparator consequently becomes slower.\n\nA larger capacitance can make \\(P,Q\\) look more like ac ground to the regenerative cross-coupled pair once the latch starts, which can strengthen regeneration/loop gain, but it does not increase the input-to-output initial gain and, if made too large, it suppresses the input information reaching the latch and greatly increases delay.",
        "format": "markdown",
        "sha256": "2dadb5ccfe47fdd1468566531b3d2da868f3512b2d2cd7e57ef077da80b41818"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer incorrectly says the initial gain decreases. It correctly notes that larger capacitance slows the node-voltage change and comparator transient, but misses that the pre-regeneration interval lengthens proportionally, so the capacitance cancels and the initial gain remains approximately unchanged.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 46949,
        "total_tokens": 48003,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 46661,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 46949,
        "total_tokens": 48003,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 46661,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of **M5 and M6 normally degrades speed** (increases the comparator delay), unless the devices were initially undersized.\n\nM5/M6 are the cross-coupled PMOS pull-up/latch devices. During the decision phase, the output nodes \\(X\\) and \\(Y\\) are precharged high, and one of them must be pulled low by the input pair and the NMOS cross-coupled pair M3/M4. Making M5/M6 wider:\n\n- adds gate/drain/junction capacitance at \\(X\\) and \\(Y\\), so the critical node discharges more slowly;\n- increases the PMOS pull-up strength, which can oppose the desired common-mode/differential change while the latch is resolving;\n- gives stronger positive feedback only after a differential has already developed, so it does not help the initial decision time.\n\nThere is an optimum: too-small M5/M6 gives weak regeneration; too-large M5/M6 gives excessive capacitance/contention. For a normally sized high-speed comparator, widening them further usually **reduces speed**, and also increases power and kickback.",
        "format": "markdown",
        "sha256": "9c8d9d55babceb6202b7882f13c969edd4f53648bbdff4f4fe901b10779d939a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies M5/M6 as cross-coupled PMOS devices and recognizes that added capacitance eventually limits speed, but it reverses the key initial trend: widening them initially strengthens regeneration and improves speed. Its claim that regeneration does not help the initial decision contradicts the central mechanism.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 27949,
        "total_tokens": 29003,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27696,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 27949,
        "total_tokens": 29003,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27696,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of **M5 and M6 normally degrades the speed** of this sense-amplifier/latch circuit; it increases the clock-to-output delay.\n\nReason:\n\n- M5 and M6 are the cross-coupled **PMOS keeper/latch** devices connected to the high-impedance nodes \\(X\\) and \\(Y\\).\n- In this circuit, during evaluation the important transition is that the input pair and the cross-coupled NMOS devices pull one of \\(X/Y\\) **low** from its precharged high level. Larger PMOS devices do not help this low-going transition.\n- Making M5/M6 wider adds significant gate/drain capacitance to \\(X\\) and \\(Y\\), so the input pair must charge/discharge a larger capacitance. It can also create more contention with the pull-down path and slow the precharge phase.\n- They should only be strong enough to hold the high node and provide sufficient positive feedback/noise margin. There is an optimum size; beyond that, increasing their widths slows the circuit.\n\nSo, for high-speed operation, **M5 and M6 should generally be kept relatively weak/minimum-sized**, not widened excessively.",
        "format": "markdown",
        "sha256": "ec885f58d85555315774f94c3727c3f41060f4e68b636177186e21b55471b4b8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M5/M6 as cross-coupled PMOS devices and notes that their added capacitance can eventually hurt speed. But it gives the opposite initial trend: wider devices strengthen regeneration, so speed initially improves before capacitance limits the benefit.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 18275,
        "total_tokens": 19329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18039,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 18275,
        "total_tokens": 19329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 18039,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "There is no unconditional “wider = faster” answer. M5/M6 are the cross-coupled PMOS positive-feedback pair of the regenerative latch, so their width has two opposing effects:\n\n- Larger \\(W_{5,6}\\) raises their transconductance \\(g_m\\), which can speed up the final latch regeneration. The regeneration time constant is roughly\n  \\[\n  \\tau \\sim \\frac{C_X+C_Y}{g_{m3}+g_{m4}+g_{m5}+g_{m6}} .\n  \\]\n- But larger \\(W_{5,6}\\) also increases the parasitic capacitance at the output nodes \\(X,Y\\) almost proportionally to \\(W\\), and strengthens the PMOS pull-up that fights the initial discharge of \\(X,Y\\). Since the comparator outputs are precharged high and the decision starts by pulling one side low, a too-strong PMOS latch acts like a keeper and delays the decision, particularly for small input differences. It also slows precharge and increases charge injection/kickback and power.\n\nSo the speed vs. \\(W_{5,6}\\) curve has an optimum. If M5/M6 are initially too weak, increasing them can improve speed. If they are already reasonably sized, as is usually the case in an optimized dynamic comparator, increasing them further typically **degrades the overall speed** and increases power. They should be sized only as strong as needed for regeneration; for high speed, optimize them by simulation rather than simply maximizing their widths.",
        "format": "markdown",
        "sha256": "a450a1d207857104ec5b2a48e47e252df9c218e4807abe31bb57bdf6acc468b4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the cross-coupled PMOS pair and the regeneration-versus-capacitance tradeoff, including an optimum width. However, it emphasizes that widening typically degrades speed once the devices are reasonably sized, rather than giving the expected initial speed improvement for the sizing increase in question.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 19311,
        "total_tokens": 20365,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19001,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1054,
        "output_tokens": 19311,
        "total_tokens": 20365,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19001,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of the clocked transistors does **not** make this C²MOS latch faster in a simple, monotonic way.\n\n- A small increase can help because it lowers the ON-resistance of the series pull-up/pull-down paths.\n- But the larger clocked devices also add diffusion capacitance directly to nodes such as \\(X\\) and \\(Y\\), add capacitance to the internal floating nodes between the clocked and data transistors, and load the \\(CK/\\bar{CK}\\) lines. In this latch, the internal nodes float during part of the cycle, so the extra capacitance/charge sharing and clock feedthrough quickly dominate.\n\nThus there is an optimum sizing, usually roughly comparable to the series data devices (often near minimum, or just large enough to make the series stack balanced). If the clocked transistors are increased much beyond that optimum, the **speed degrades**, not improves. So, in the usual design sense, oversizing the clocked transistors slows the circuit down.",
        "format": "markdown",
        "sha256": "71947aa67cc63cefd281e0fdcada2ad91f08aac766fa830ecb64dfd856fd0d4f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly says widening initially reduces series on-resistance and improves speed, while added capacitance eventually limits or reverses the benefit at an optimum width. Extra discussion of internal-node effects and sizing is not needed for the central answer.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1029,
        "output_tokens": 41938,
        "total_tokens": 42967,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41737,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1029,
        "output_tokens": 41938,
        "total_tokens": 42967,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41737,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of the **clocked transistors** generally **degrades the speed** of this TSPC/clocked-CMOS register. In the usual minimum-sized design, making them wider increases the diffusion capacitance at the internal nodes \\(x\\) and \\(y\\) and increases the load on the \\(CK/\\overline{CK}\\) lines. The data transistors still limit the series stack current, so the reduction in clock-transistor on-resistance gives little benefit, while the added capacitance and clock skew slow the precharge/evaluate transitions and increase power.\n\nStrictly, there can be an optimum size if the clocked devices were initially very undersized; a modest increase may help until that optimum. But beyond that—and for normally sized clocked transistors—the overall speed worsens. Therefore clocked transistors should normally be kept small/minimum-sized; do not widen them to improve speed.",
        "format": "markdown",
        "sha256": "fba631781aa13383196160b765a490aebc94af907044784e3c9410a4fb9ae3c9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It mentions a possible optimum, but its main conclusion is that widening generally degrades speed and that the resistance reduction gives little benefit. The golden answer says widening improves speed initially as on-resistance falls, with added capacitance limiting or reversing the benefit only at larger widths.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1029,
        "output_tokens": 32787,
        "total_tokens": 33816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34201,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1029,
        "output_tokens": 32787,
        "total_tokens": 33816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 34201,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the width of the clocked transistors is **not simply a speed improvement**. There is an optimum, and beyond that optimum the speed **degrades**.\n\n- Wider clocked devices reduce their ON-resistance, which can slightly speed up charging/discharging of the internal nodes \\(x\\) and \\(y\\) when the stage turns on.\n- But those same devices add diffusion capacitance directly at the high-impedance nodes \\(x\\) and \\(y\\), increase the clock-line capacitance \\(C_{CK}, C_{\\overline{CK}}\\), and increase clock feedthrough/charge injection when the clock switches.\n- In this clocked latch/frequency-divider, the current is ultimately limited by the fixed non-clocked devices and the load at \\(x/y\\). Once the clocked transistors are large enough that their series resistance is negligible, making them still wider only adds capacitance and slows the circuit.\n\nSo, in the usual design range, increasing the clocked transistor widths beyond a small optimum **degrades the maximum speed**; they should be kept near minimum or optimized together with the data transistors, rather than widened arbitrarily.",
        "format": "markdown",
        "sha256": "917a045482f7247836231973e2b53c6d3383f2ac35cbe27800eed766e6f5f639"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It identifies the initial benefit from reduced clocked-device on-resistance and the eventual capacitance penalty, giving the expected optimum and degradation beyond it. The extra bottleneck discussion does not contradict that trend.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1029,
        "output_tokens": 36249,
        "total_tokens": 37278,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1029,
        "output_tokens": 36249,
        "total_tokens": 37278,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 36025,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes. With ideal complementary clocks, the circuit is a two-stage clocked-inverter/latch frequency divider:\n\n- When \\(CK\\) is high, the left stage is transparent: \\(x=\\overline z\\). Since \\(z=\\overline y\\), this gives \\(x=y\\).\n- When \\(CK\\) is low, the right stage is transparent: \\(y=\\overline x\\). The other node holds.\n\nThus \\(x\\) and \\(y\\) toggle at half the clock frequency, with their transitions separated by half a clock period. Since their output period is two clock periods, that separation is\n\\[\n\\frac{T_{CK}/2}{2T_{CK}}\\cdot 360^\\circ = 90^\\circ.\n\\]\nTherefore \\(x\\) and \\(y\\) are quadrature outputs. Also, since \\(z=\\overline y\\), \\(z\\) is quadrature with \\(x\\) but in antiphase with \\(y\\). Exact quadrature requires a 50% duty-cycle clock and well-matched delays; real circuits can have phase error.",
        "format": "markdown",
        "sha256": "6404c9dfd50290587eb9435736355a5ab7d31adfbc06ebdf5d11a96269ce2519"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies nominal divide-by-two quadrature and the half-clock-period transition spacing. It notes delay mismatch can cause phase error, but does not explain the unequal latch loading or the specific Inv3 delay that skews Z.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 11051,
        "total_tokens": 12066,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10348,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 11051,
        "total_tokens": 12066,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10348,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes—ideally, the structure is a master–slave/divide-by-two type circuit and can provide quadrature outputs.\n\nThe two latch stages are clocked on opposite phases (\\(CK\\) and \\(\\overline{CK}\\)). With the feedback inverter \\(Inv_3\\), the circuit behaves as a divide-by-two stage. The internal node \\(x\\) changes on the opposite clock phase from the output \\(y\\). If the input clock period is \\(T_{CK}\\), the divided output period is \\(2T_{CK}\\), and the delay between \\(x\\) and \\(y\\) is \\(T_{CK}/2\\), which is\n\n\\[\n\\frac{T_{CK}/2}{2T_{CK}}\\cdot 360^\\circ = 90^\\circ .\n\\]\n\nSo \\(x\\) and \\(y\\) are the two quadrature phases at \\(f_{CK}/2\\). The node \\(z\\) is simply the complement of \\(y\\) (\\(180^\\circ\\) phase). To obtain all four phases, \\(0^\\circ,90^\\circ,180^\\circ,270^\\circ\\), you would also need the complement of \\(x\\), e.g. by adding/buffering an inverter or using the differential node if available.\n\nIn practice, exact quadrature requires matched latch delays, symmetrical layout, and buffered outputs; mismatches/delay/loading cause phase error.",
        "format": "markdown",
        "sha256": "7ff3283b012ef583d70bdf3be75745a5344d2e31eceebb5ffce871fd422d4192"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the divide-by-two operation and nominal 90° relationship between X and Y, and notes that delay and loading can cause phase error. It does not specifically explain the Inv3 delay skewing Z or the unequal loading of the two latch outputs, as required for full credit.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 18109,
        "total_tokens": 19124,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17826,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 18109,
        "total_tokens": 19124,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17826,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes—if both phases are brought out.** The core is a divide-by-2 master–slave type divider. During one clock phase node \\(X\\) is set, and during the opposite phase \\(Z\\) is updated; thus \\(X\\) and \\(Z\\) change on opposite clock edges. With a 50% duty-cycle clock, the edge separation is half an input-clock period, which is one quarter of the divided output period—i.e. \\(90^\\circ\\). So \\(X\\) and \\(Z\\) (or \\(X\\) and \\(Y\\)) can be used as quadrature outputs; \\(Y\\) and \\(Z\\) are complements, not quadrature.\n\nHowever, the single buffered terminal \\(Z\\) alone is **not** a quadrature output. For practical use, node \\(X\\) must be buffered/driven without disturbing the divider. Also, non-50% clock duty-cycle, device mismatch, and unequal buffer delays will introduce phase error.",
        "format": "markdown",
        "sha256": "f5bee90814a745370c0755bfa1f631c73ff94786ee9901ae3f92509d508ede9d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies nominal quadrature from the latches switching on opposite clock edges and notes phase error from delays. It does not explain the unequal loading of the two latch outputs, a key source of nonideal phase error.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 23261,
        "total_tokens": 24276,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23061,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1015,
        "output_tokens": 23261,
        "total_tokens": 24276,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 23061,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Do **not** simply make the clocked transistors wider to improve speed. There is an optimum size.\n\nWidening them reduces their ON resistance, so a modest increase can make the clocked inverters switch faster. However, it also increases:\n\n- diffusion capacitance at the internal nodes between the clocked and non-clocked devices,\n- gate capacitance on \\(CK\\) and \\(\\overline{CK}\\),\n- clock feed-through/charge-sharing effects at the floating nodes.\n\nIn this clocked-CMOS (C2MOS latch) circuit, once the clocked devices are comparable to the non-clocked devices, the extra capacitance dominates: the added charge must be moved every clock transition, the clock edge is loaded more, and the benefit from lower \\(R_{\\rm on}\\) becomes small. The delay therefore has a minimum versus width; beyond that, **increasing the widths degrades the overall speed** and increases dynamic power.\n\nSo: a small increase may help, but over-sizing the clocked transistors slows the circuit; they should be sized at the optimum, not maximum width.",
        "format": "markdown",
        "sha256": "0e337343b3d85a84f3f7a302e763d24eb59458d4b3b74eca91a1787788e8716f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It says widening first helps by reducing on-resistance, then excessive sizing can slow the circuit, and identifies charge sharing and clock loading as limits—an outcome explicitly allowed by the golden solution.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 39466,
        "total_tokens": 40503,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 39248,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 39466,
        "total_tokens": 40503,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 39248,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of the clocked transistors does **not improve the speed of this circuit once they are adequately sized; in fact it usually degrades it**.\n\nThe clocked devices act mainly as switches in the clocked CMOS inverters. Making them wider does reduce their ON resistance, but it also:\n\n- increases the diffusion capacitance at the internal, often floating/high-impedance nodes of the clocked inverters,\n- increases the capacitance seen by the clock lines \\(CK\\) and \\(\\overline{CK}\\),\n- makes charge sharing/clock feedthrough at the storage/dynamic nodes worse,\n- and slows the clock edge if the clock driver has finite strength.\n\nIn this latch/register loop, those extra capacitances must be charged or discharged every cycle, and the reduction in switch resistance saturates. Therefore, beyond a modest optimum, additional width slows the loop. The clocked transistors are normally kept minimum or only as large as needed; the data transistors are the ones sized for speed.\n\nSo: **the speed worsens (or at best stays nearly the same) when the clocked transistors are made wider; it does not improve for a normal design point.** If they were initially undersized, a small increase could help, but there is an optimum beyond which widening them degrades performance.",
        "format": "markdown",
        "sha256": "f4db3b27e39e67059d59fe8b598827052c45990ee979f606cbdaee4724c13c46"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "The answer allows an initial speed improvement when the switches are undersized, followed by an optimum and degradation as width increases, and identifies charge sharing as a limiting effect. This matches the golden solution’s explicit full-credit rule for that trend.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 42413,
        "total_tokens": 43450,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 42150,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 42413,
        "total_tokens": 43450,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 42150,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of the clocked transistors is **not simply a speed-up**.\n\n- They are in series with the active path, so increasing their width \\(W\\) lowers their on-resistance, which tends to **improve** the local data-path delay.\n- But increasing \\(W\\) also increases their gate capacitance (loading the clock) and their drain/source diffusion capacitance at the internal nodes. The clock line is usually a critical, heavily loaded net, so this can dominate.\n\nHence the delay has an **optimum**. Starting from an undersized clocked device, making it wider can speed things up; once it is about the same size as the data devices, further widening typically **degrades the overall speed** because the extra clock and internal-node capacitance outweighs the small reduction in \\(R_{\\rm on}\\).\n\nIn practice, clocked transistors in a clocked-CMOS/C²MOS latch are kept no larger than necessary—usually comparable to or slightly larger than the data transistors—to make their on-resistance negligible without adding excessive clock load. A blanket increase of their widths will generally **not improve the speed** and can make it worse.",
        "format": "markdown",
        "sha256": "4bd592c6442003a01126608e657c5257ea44cf86d2bea634cf998ae73e8db4c1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly notes that widening lowers on-resistance, but overstates clock and internal-node capacitance as dominant and concludes that further widening generally degrades speed. The topology’s key result is that widening improves speed considerably; the answer also misses charge sharing as the swing-degradation limit.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 49706,
        "total_tokens": 50743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 49473,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1037,
        "output_tokens": 49706,
        "total_tokens": 50743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 49473,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure is a **clocked feedback loop**:\n\n\\[\nQ \\;\\xrightarrow[\\;CK\\;]{} \\text{Inv}_1 \n\\;\\xrightarrow[\\;\\overline{CK}\\;]{} \n\\text{Inv}_2 \\rightarrow \\text{Inv}_3 \\rightarrow Q\n\\]\n\nSo the loop contains **three inverters**, i.e. odd inversion, and two switches driven by complementary clock phases.\n\nAssume the switch labeled \\(CK\\) is on when \\(CK=1\\), and the \\(\\overline{CK}\\) switch is on when \\(CK=0\\).\n\n- **When \\(CK=1\\):** first switch is closed, second open. The output \\(Q\\) drives the input of \\(\\text{Inv}_1\\), producing \\(\\overline Q\\). The two-inverter section is isolated and holds its previous state only on parasitic capacitance.\n- **When \\(CK=0\\):** first switch opens, second closes. The prepared value \\(\\overline Q\\) is transferred through the non-inverting two-inverter section to the output, so \\(Q\\) becomes complemented.\n\nThus, for a periodic clock,\n\n\\[\nQ_{n+1}=\\overline{Q_n},\n\\]\n\nso the arrangement behaves as a **dynamic toggle flip-flop / divide-by-two circuit** (output changes on one clock edge; \\(f_Q=f_{CK}/2\\)). It is not a true static latch as drawn, because the stored state is retained only by charge on floating nodes.\n\nTwo important points:\n\n1. **Clock overlap is dangerous.** If both switches are ever on simultaneously, the three-inverter loop is closed. A closed loop with an odd number of inversions has no stable dc state and can oscillate/race. It then behaves like a three-stage ring oscillator with frequency approximately\n   \\[\n   f_{\\rm osc}\\approx \\frac{1}{2(t_{\\rm Inv1}+t_{\\rm Inv2}+t_{\\rm Inv3})}.\n   \\]\n   For identical inverter delays \\(t_d\\), \\(f_{\\rm osc}\\approx 1/(6t_d)\\). This can cause metastability or corrupt stored data.\n2. **No external data input is shown.** As drawn, it is an autonomous clocked loop. A normal static memory element would require an even-inversion feedback loop, a keeper, or an explicit data input; a proper two-phase clock should be non-overlapping, and the state must be refreshed periodically because dynamic nodes can leak.\n\nIn short: it is a **dynamic clocked toggle/divider loop**, and it becomes an **unstable ring oscillator/race hazard** if \\(CK\\) and \\(\\overline{CK}\\) overlap.",
        "format": "markdown",
        "sha256": "d480c79b899d41209ab8c5ec1963dff61c7b2d2a43bbc8d5181e06e696b61a04"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the circuit as a dynamic clocked toggle/divide-by-two loop with output frequency half the clock frequency, satisfying the golden solution’s full-credit rule. The extra internal-path and overlap discussion is not required.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 20052,
        "total_tokens": 20722,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19509,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 20052,
        "total_tokens": 20722,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19509,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure is a **closed, clock-controlled inverter loop**—a dynamic (charge-storage) feedback circuit. Label the switch controlled by \\(CK\\) as \\(S_1\\) and the one controlled by \\(\\overline{CK}\\) as \\(S_2\\). Let \\(Q\\) be the fed-back output at the far right.\n\nAssume non-overlapping clock phases:\n\n| Phase | \\(S_1\\) | \\(S_2\\) | Node behavior |\n|---|---|---|---|\n| \\(CK=1\\) | ON | OFF | \\(Inv_1\\) samples \\(Q\\), so its output becomes \\(\\bar Q\\). The right-hand side is isolated and holds its previous value, so \\(Q\\) is retained. |\n| \\(CK=0\\) | OFF | ON | The stored \\(\\bar Q\\) is passed through the second switch and then through **two inverters**, so the two inverters do not change the logic level. Thus \\(Q\\) becomes the previously stored \\(\\bar Q\\). |\n\nTherefore, once per complete clock cycle,\n\\[\nQ_{n+1}=\\overline{Q_n}.\n\\]\nSo, with a running clock, \\(Q\\) toggles every clock period. The output is a square wave at\n\\[\nf_Q=\\frac{f_{CK}}{2},\n\\]\ni.e. the circuit acts as a **clocked toggle flip-flop / divide-by-two frequency divider**.\n\nImportant points:\n\n- The two inverters after \\(\\overline{CK}\\) form a **non-inverting buffer/delay**; logically \\(Q\\) equals the node just after the second switch.\n- This is a **dynamic** circuit: when one switch is open, the isolated node stores charge on capacitance. Leakage eventually destroys the state, so continuous clocking or a keeper/refresh circuit is needed.\n- If the clock phases overlap and both switches are on simultaneously, the closed loop contains **three inverters**, giving \\(Q=\\bar Q\\). It then has no stable binary state and behaves as a **three-stage ring oscillator** (or may settle near the inverter switching threshold with high short-circuit current). Such overlap is generally undesirable.\n- If the intended use is a static latch, the arrangement as drawn is not a robust static memory: a static latch should use positive feedback with an even number of inversions or a cross-coupled keeper.\n- The state is not defined at power-up unless a reset/initialization is provided.",
        "format": "markdown",
        "sha256": "004d7b098994a9c250c21863cb0e5fb2701ef3cfbed4c331c4a461d654f27ebe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies a dynamic, clocked divide-by-two circuit and states that its output frequency is half the clock frequency. Its additional internal-path and overlap discussion is not needed for full credit.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 19918,
        "total_tokens": 20588,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19426,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 19918,
        "total_tokens": 20588,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19426,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure shows a **closed-loop, clock-controlled inverter chain**—essentially a dynamic ring counter / clocked ring oscillator. Reading the symbols:\n\n- The triangles with a bubble are inverters (NOT gates); one is labeled \\(Inv_1\\).\n- The small-circle/slant symbols are switches or transmission gates.\n- The switches are driven by two complementary clock phases, \\(CK\\) and \\(\\overline{CK}\\).\n- The last inverter output is fed back through the lower wire to the input, so the circuit is a feedback loop, not a one-way chain.\n- There are three inverter stages (an odd number) separated by clocked switches.\n\nOperation:\n\n1. If all switches were permanently closed, the loop would contain three inversions. An odd number of inversions in a closed loop has no stable dc state, so it would behave as a **three-stage ring oscillator**, with frequency approximately  \n   \\[\n   f \\approx \\frac{1}{2(T_1+T_2+T_3)}\n   \\]\n   where \\(T_i\\) are the propagation delays of the stages. For equal delays \\(\\tau\\),  \n   \\[\n   f\\approx \\frac{1}{6\\tau},\\qquad T_{\\rm osc}\\approx 6\\tau.\n   \\]\n\n2. In normal two-phase clocking, the switches conduct on alternate phases. The loop samples and transfers charge/logic level stage by stage. With \\(CK,\\overline{CK}\\) alternating and three inverting stages, the loop cannot remain static; the nodal states alternate. For ideal gates, if \\(Q_1,Q_2,Q_3\\) are the inverter outputs, a possible steady sequence is:\n   \\[\n   \\begin{array}{c|ccc}\n   \\text{phase} & Q_1&Q_2&Q_3\\\\\\hline\n   CK=1 & 1&1&0\\\\\n   CK=0 & 1&0&0\\\\\n   CK=1 & 0&0&1\\\\\n   CK=0 & 0&1&1\\\\\n   CK=1 & 1&1&0\n   \\end{array}\n   \\]\n   and its complement is also possible. Thus each node is a square wave at half the clock frequency:\n   \\[\n   f_{\\rm out}=\\frac{f_{CK}}{2}.\n   \\]\n   So the arrangement operates as a **dynamic divide-by-two clocked ring counter** (or a frequency divider), with the states stored temporarily on the capacitances when switches are open.\n\nPractical points:\n\n- \\(CK\\) and \\(\\overline{CK}\\) should be non-overlapping; if both phases conduct simultaneously, the loop can race or latch unpredictably.\n- Because the storage is dynamic, the clock must run fast enough that leakage does not erase the state before the next refresh.\n- Real mismatch, noise, and finite rise times can resolve metastable/start-up states; in a symmetric ideal model the initial condition sets which phase sequence occurs.\n- If the switches are treated simply as enabling devices and held closed, the same circuit is the classic three-inverter ring oscillator.\n\nIn short: **it is a three-stage clocked inverting feedback loop—normally a dynamic frequency divider/ring counter; without clocked interruption it is a three-stage ring oscillator.**",
        "format": "markdown",
        "sha256": "bd734b25df27131dc6bf07f0deb6e7faf8207faf82349a73e6acfea857b877c4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the arrangement as a dynamic divide-by-two and explains clocked sampling and temporary charge storage. The extra ring-oscillator discussion is not needed, but does not change the essential answer.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 25918,
        "total_tokens": 26588,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25695,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 670,
        "output_tokens": 25918,
        "total_tokens": 26588,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25695,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter is an **always-on feedback (keeper) inverter** connected between the final feedback/output node and the output node of \\(\\mathrm{Inv}_1\\). Its effect is a trade-off:\n\n- **When the CK switch is closed**, it is effectively in parallel with \\(\\mathrm{Inv}_1\\). This increases the drive at that internal node, so the node can switch faster and is less sensitive to leakage/noise. However, it also adds input capacitance to the preceding node and increases short-circuit/crowbar current during transitions. If the previous stage is weak, the extra load can actually slow the overall path.\n\n- **When the CK switch is open**, it keeps the internal node defined instead of letting it float. This makes the circuit more static/robust: it improves noise margin and removes the low-frequency/leakage problem of a purely dynamic node. But it also fights any new value being transferred through the clocked path (a ratioed contention). If it is too strong, the node may not switch; if too weak, it may not hold reliably.\n\n- **Feedback/loop behavior:** In the phase where the second switch is closed, the red inverter plus the two following inverters form an odd-inversion feedback loop. If that loop is closed long enough, it can **ring or oscillate**. This can be intentional in an oscillator, where it sets/changes the frequency and can affect duty cycle/jitter; but in a latch or divider, it is generally undesirable unless the keeper is weak or clocked off.\n\n- **Power/area:** It adds area, gate capacitance, and extra dynamic/short-circuit power. A keeper inverter is therefore usually made weak; if robustness is not required, removing it or making it clocked improves speed and power but risks floating-node/leakage failures.\n\nIn short: the red inverter improves static robustness and can increase local drive, but at the cost of extra capacitance, contention, power, and possible unwanted oscillation/ratio limitations.",
        "format": "markdown",
        "sha256": "53c871282e9df0b218ebc1bf0d080e1f54a27de3d9577c3598c15b70fabc7465"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the red inverter as a keeper rather than a feedforward path bypassing the CK switch and Inv1. Although it notices a possible oscillating loop and contention, it incorrectly claims the inverter removes the low-frequency problem; in fact, the unclocked branch can corrupt division at low rates and raises the minimum usable clock frequency.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 36197,
        "total_tokens": 36811,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35791,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 36197,
        "total_tokens": 36811,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35791,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter is a **feed-forward/auxiliary inversion path** from the oscillator/feedback node to the internal node between Inv1 and the \\(\\overline{CK}\\) switch. It is effectively in parallel with the “CK switch + Inv1” branch when that switch is closed, and it remains connected when the switch is open.\n\nIts main effects are:\n\n- **Higher speed / higher oscillation or clock frequency:** When the CK switch is on, the red inverter and Inv1 drive the same internal node with the same polarity. Their transconductances add, reducing the node’s delay and rise/fall time. It also bypasses the on-resistance of the CK switch and the input delay of Inv1. The oscillator/divider loop therefore has more gain and shorter effective delay, allowing faster operation and often a wider locking/tuning range.\n\n- **Regeneration / startup / holding:** When the CK switch is open, the red inverter still defines the internal node from the output node; it acts like a keeper/precharge path, reducing floating-node and charge-sharing problems. In a ring oscillator or divider it can supply the extra inversion needed for the loop to oscillate rather than merely latch. This makes startup and high-speed operation more robust.\n\n- **Costs:** It adds capacitance/load, dynamic current, and possible crowbar/short-circuit current if it fights Inv1. It can also create an always-on feedback path—causing spurious self-oscillation, multiple oscillation modes, worse jitter/phase noise, and duty-cycle error—and may prevent the circuit from truly turning off. If it is too strong, it can dominate Inv1 and effectively bypass the CK switch, so the circuit no longer behaves as a clean clocked/hold circuit.\n\nSo the red inverter generally **improves speed, loop gain, startup, and locking/operating range, but at the expense of power and possible contention/noise/spurious modes**. If it is intended only as a keeper, it should be made weak; if it is a speed/lock-range booster, its size must be chosen so that it does not overpower the clocked path.",
        "format": "markdown",
        "sha256": "39d0636578f8585c6e2e6cd23102a1ef45331c09e8b49009cc7565c20812962d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the feedforward bypass and its speed benefit, and notes possible self-oscillation and contention. But it miscasts the branch as a keeper and does not state the key low-frequency consequence: the unclocked loop can corrupt division and raise the minimum usable clock frequency; its claims of improved operating/locking range are unsupported.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 24485,
        "total_tokens": 25099,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24049,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 24485,
        "total_tokens": 25099,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24049,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter is acting as a **feedback/keeper inverter** around the latch node. It forms a positive-feedback loop with `Inv1`.\n\n- **Function:** When the clock-controlled transmission gate turns off, the input node of `Inv1` would float. The red inverter drives it back to the stored logic level, so the latch retains its previous state. This prevents leakage, charge sharing, noise, and glitches—important in a clock-gating/latch circuit.\n\n- **Timing/performance cost:** While the transmission gate is on, the keeper opposes any new data that tries to change the stored value. The input driver must overcome it, so the red inverter adds contention and capacitance. This increases the latch’s setup time and data-to-output delay and can reduce the maximum clock frequency. If it is too strong, the latch can even fail to be written; if too weak, the stored state may be lost through leakage or noise.\n\n- **Power/area:** During transitions, the keeper and the forward inverter can both conduct, causing extra short-circuit/crowbar current and dynamic power. It also adds area and load capacitance.\n\nTherefore, a keeper inverter is normally made **weak**—minimum width, long channel, and/or higher threshold—or replaced by a **clocked/tri-state feedback inverter** that turns off during the transparent phase. That gives the storage robustness without strongly fighting the input.\n\nIf the highlighted inverter is instead only the `CK`-to-`\\bar{CK}` clock inverter rather than a keeper, then its delay/skew is what matters: it can create temporary overlap/dead time between the two transmission gates, causing charge sharing, short-circuit current, and timing margin loss. Matching and sizing it to `CK` is then the key issue.",
        "format": "markdown",
        "sha256": "23d0938ee37d456631fda5613ba79926a82df74fa2f576c44184941142671833"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the red inverter as a keeper/feedback path. The actual inverter creates an unclocked feedforward path that bypasses part of the first latch, improving high-speed operation but raising the minimum usable clock frequency at low rates.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 25556,
        "total_tokens": 26170,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27884,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 614,
        "output_tokens": 25556,
        "total_tokens": 26170,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 27884,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No—not in the sense stated. The red inverter is **not cross-coupled with `Inv1`** in the drawing, and it is not a conventional keeper that makes the dynamic circuit static and removes the leakage-imposed minimum clock frequency.\n\nLet the left feedback node before the `CK` switch be \\(A\\), the input of `Inv1` be \\(B\\), and the output of `Inv1` be \\(C\\). Then:\n\n- `Inv1` does \\(C=\\bar B\\).\n- The `CK` switch, when closed, makes \\(B=A\\).\n- The red inverter is connected from \\(A\\) to \\(C\\), so it enforces \\(C=\\bar A\\).\n\nSo:\n\n1. **When the `CK` switch is closed**, \\(A=B\\), and the red inverter is simply in parallel with `Inv1`. They both try to produce the same output. This is not a cross-coupled latch; a cross-coupled latch needs the second inverter’s output to drive the first inverter’s input, i.e. \\(C\\to B\\), not \\(A\\to C\\).\n\n2. **When the `CK` switch is open**, the red inverter bypasses the first clocked stage. It then can close a loop through the other switch and `Inv2`/`Inv3`. That loop has an odd number of inversions when the \\(\\overline{CK}\\) switch is closed, so it is regenerative/oscillatory rather than a stable two-inverter storage loop. It keeps the loop defined/oscillating; it does not “hold” a DC state.\n\nA real keeper for `Inv1` would be a **weak inverter connected from the output of `Inv1` back to its input/dynamic storage node**, forming a positive-feedback latch so that when the clock switch opens the node retains its value. That weak keeper can be overridden during evaluation and can reduce the minimum clock-frequency problem caused by leakage. The red inverter as drawn is instead an **always-on feedforward/bypass inverter around the first clocked stage**. In some very loose terminology, a weak parallel inverter used to support a tri-stated node may be called a “keeper,” but the quoted description “cross-coupled latch with `Inv1`” is wrong, and one such device does not by itself eliminate the leakage constraint for the whole dynamic loop.\n\nSo I would reject the quoted answer as stated. The red inverter’s actual function is to provide an inverse copy of the loop-output node at the output of `Inv1` during the phase when the `CK` switch is off—i.e. it bypasses/continues the feedback path—not to store the node’s state as a cross-coupled keeper.",
        "format": "markdown",
        "sha256": "a69c9a196fd4c9552745b868413324f804d2c6f3fc285e9e980c3120cc60e308"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly rejects the keeper interpretation and identifies the red inverter as an unclocked feedforward bypass, including the odd-inversion loop. It omits the key frequency tradeoff: the branch can help at high rates but overpower the intended latch behavior at low rates, raising the minimum usable clock frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 657,
        "output_tokens": 51535,
        "total_tokens": 52192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 50978,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 657,
        "output_tokens": 51535,
        "total_tokens": 52192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 50978,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "I think the key point is that the quoted answer is **not quite right in its wording**, although it is pointing at the right general idea.\n\nThe red inverter is not a “keeper that forms a cross-coupled latch with `Inv1`” in the usual sense. A keeper is normally a weak inverter connected in the feedback loop so that the latch’s state is held when the clock is stopped. In this figure, the red inverter is connected across the first inverter/clock switch, so its role is to provide a **weak feedback/keeper path** that holds the internal node and prevents it from being lost by leakage. That is why it can relax the “minimum clock frequency” requirement of a dynamic latch.\n\nMore precisely:\n\n- The red inverter is a **weak keeper** (often drawn weak/small in a real design).\n- It is used to maintain the state of the dynamic latch when the clock is stopped or the clock period is very long.\n- It does not “remove” the clock frequency requirement in a fundamental sense; it makes the latch **static-like** so that leakage-induced state loss is avoided, or at least greatly reduced. If the keeper is weak or the leakage is too high, the state can still eventually be lost.\n- It is not a cross-coupled latch with `Inv1` in the sense of two inverters directly in a closed loop. It is an auxiliary feedback/keeper path used to keep the node from floating and to compensate for leakage.\n\nSo: **partially agree, but the “cross-coupled latch with Inv1” wording is misleading.** The actual role is to provide a weak keeper/feedback path that prevents the dynamic node from floating and thus removes the need for a minimum clock frequency for proper operation.",
        "format": "markdown",
        "sha256": "6562509bd0c1e57d712c2a8211857db30b4c75c009edfdd50d313f5b480fcaf7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the red inverter as a keeper/feedback path and claims it relaxes the minimum-frequency limit. It is actually an unclocked feedforward branch that bypasses part of the latch path, helping at high rates but potentially corrupting operation at low rates.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 285,
        "output_tokens": 48491,
        "total_tokens": 48776,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 48136,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 285,
        "output_tokens": 48491,
        "total_tokens": 48776,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 48136,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No. As drawn, the red inverter is **not** a keeper and it does **not** form a cross-coupled latch with `Inv1`.\n\nLet\n\n- \\(X\\) = the left-hand node (also connected to the feedback wire from the final output),\n- \\(Y\\) = input of `Inv1` (right of the CK switch),\n- \\(Z\\) = output of `Inv1`.\n\nThe red inverter is connected from \\(X\\) to \\(Z\\). `Inv1` is connected from \\(Y\\) to \\(Z\\), with the CK switch between \\(X\\) and \\(Y\\).\n\n- When CK is closed, \\(X=Y\\), so the red inverter and `Inv1` are simply **two inverters in parallel** driving \\(Z\\). They are not cross-coupled.\n- When CK is open, \\(Y\\) is isolated, but the red inverter still forces\n  \\[\n  Z=\\overline X .\n  \\]\n  Thus it **bypasses the CK switch**; it does not hold the actual isolated storage node \\(Y\\).\n\nA real keeper/staticizer would be a **weak inverter connected from the output of `Inv1` back to its isolated input**, i.e. \\(Z\\to Y\\), so that `Inv1` and the keeper form a positive-feedback cross-coupled latch during the hold phase. It must be weak enough to be overridden when the input switch turns on. The red inverter in this figure does not do that.\n\nIn the complete loop, the red path is an always-on feed-forward/bypass path. Together with the other inverters it can close a loop with an odd number of inversions in one clock phase; that is a race/regenerative or ring-oscillator-type path, not a stable charge-holding latch. Therefore it cannot “remove” the minimum-clock-frequency constraint caused by leakage. At best it changes the logic/clocking of the stage; at worst it causes contention, charge sharing, or oscillation if the clock is held.\n\nSo the cited answer is incorrect on both points: the red inverter is not cross-coupled with `Inv1`, and it is not a leakage keeper. Its role is essentially an **always-on inverter/bypass around the first clocked inverter**, not a staticizer. To eliminate the minimum clock-frequency requirement, use a properly connected weak keeper/staticizer on the actual dynamic node.",
        "format": "markdown",
        "sha256": "c95b5944224cc712664661ff618b1afef85745c4ef990acd525c2d8139c0dada"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly rejects the keeper interpretation and identifies the red inverter as an unclocked feedforward bypass, not a hold path. It omits the key tradeoff: the bypass can improve high-speed operation but can overpower the latch path at low clock rates and raise the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 657,
        "output_tokens": 63663,
        "total_tokens": 64320,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 63174,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 657,
        "output_tokens": 63663,
        "total_tokens": 64320,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 63174,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "A 50 Ω input resistance is only one design constraint; it does not by itself give a unique minimum-noise design.  You must also specify allowable power, gain, bandwidth, output load, and technology.  The usual procedure is to write \\(R_{in}\\) and the noise factor \\(F\\) of the shunt-feedback inverter, impose \\(R_{in}=50\\Omega\\), and then minimize \\(F\\) with respect to the remaining design variables (transistor widths, bias current, feedback resistor, etc.).\n\nFor the circuit shown, let  \n\\[\ng_m=g_{m1}+g_{m2},\\qquad g_{ds}=g_{ds1}+g_{ds2}\n\\]\nbe the total inverter small-signal transconductance and output conductance, and let \\(R_F\\) be the feedback resistor.  At low frequencies,\n\\[\nR_{in}=\\frac{R_F}{1+A_v}\n      =\\frac{1+g_{ds}R_F}{g_m+g_{ds}},\n\\]\nwhere\n\\[\nA_v=\\frac{g_mR_F-1}{1+g_{ds}R_F}\n\\]\nis the voltage gain.  If the output conductance is small,\n\\[\nR_{in}\\approx \\frac{1}{g_m}\\qquad(g_mR_F\\gg1),\n\\]\nso\n\\[\nR_{in}=50\\,\\Omega\\quad\\Rightarrow\\quad\ng_m\\approx \\frac{1}{50\\,\\Omega}=20\\ {\\rm mS}.\n\\]\nIf \\(g_{ds}\\) is not negligible, \\(R_F\\) must be chosen as\n\\[\nR_F=\\frac{R_{in}(g_m+g_{ds})-1}{g_{ds}},\n\\]\nso that \\(R_{in}=50\\,\\Omega\\).\n\nTo first order, the noise factor is approximately\n\\[\nF\\approx 1+\\frac{\\gamma}{g_mR_s}+\\frac{\\alpha R_s}{R_F},\n\\]\nwhere \\(\\gamma\\approx 2/3\\) for a long-channel MOSFET (higher in short-channel devices), \\(R_s=R_{in}=50\\,\\Omega\\), and \\(\\alpha\\) is of order unity and depends on the output loading, gain, and exact topology.  With the ideal high-output-impedance approximation,\n\\[\nF\\approx 1+\\gamma+\\frac{4(1+\\gamma)R_s}{R_F}\n\\]\nwhen \\(g_m\\approx 1/R_s\\).  The exact feedback term depends on the output load and parasitics; use a circuit simulator for the final value.\n\nThus, for a fixed \\(R_{in}=50\\,\\Omega\\):\n\n- **Make \\(R_F\\) as large as the gain/bandwidth/linearity budget permits.**  \n  The feedback resistor is one of the main noise contributors; its noise contribution falls as \\(1/R_F\\).  A small \\(R_F\\) improves bandwidth but degrades NF.\n\n- **Set the total transistor transconductance from the matching condition.**  \n  For a high-gain, high-\\(r_o\\) design, \\(g_{m1}+g_{m2}\\approx 1/50\\,\\Omega=20\\,{\\rm mS}\\).  If the output conductance is significant, use the exact relation above to choose \\(R_F\\) for \\(R_{in}=50\\,\\Omega\\).\n\n- **Bias M1 and M2 for high \\(g_m/I_D\\), low excess noise factor, and sufficient \\(r_o\\).**  \n  Use the minimum overdrive/current density that still gives enough speed, and use a longer channel or a cascode if it improves \\(r_o\\) and the intrinsic gain.  In long-channel devices, the thermal noise current is\n  \\[\n  \\overline{i_{d}^{2}}=4kT\\gamma g_m\\Delta f,\n  \\]\n  so for a fixed total \\(g_m\\) the NMOS/PMOS split matters only through the weighted sum\n  \\[\n  \\gamma_N g_{m1}+\\gamma_P g_{m2}.\n  \\]\n  Allocate more \\(g_m\\) to the device with lower excess noise, if that is allowed.\n\n- **At high frequency, do not simply maximize the width.**  \n  The input capacitance \\(C_{gs}\\) and the induced gate noise change the optimum.  Choose the transistor widths so that the required 50 Ω input impedance coincides with the optimum noise impedance at the frequency of interest; this is the noise-matching condition.  In practice, sweep \\(W_N,W_P,L,I_{\\rm bias}\\) and \\(R_F\\) in simulation and minimize NF subject to \\(S_{11}\\), bandwidth, gain, and linearity.\n\n- **Ideal lower bound.**  \n  With a simple long-channel model and large \\(R_F\\), the matched common-source/inverter stage cannot go below approximately\n  \\[\n  F_{\\min}\\approx 1+\\gamma,\n  \\]\n  i.e. \\(NF_{\\min}\\approx 2.2\\ {\\rm dB}\\) for \\(\\gamma=2/3\\) (about \\(3\\ {\\rm dB}\\) for \\(\\gamma=1\\)).  Real short-channel devices, finite \\(R_F\\), parasitic capacitance, and output loading give higher values.  If there is no power, gain, or bandwidth limit, increasing the open-loop gain and \\(R_F\\) with more power can drive the noise factor closer to unity, so the problem has no finite optimum without those additional constraints.\n\nIn short: enforce \\(R_{in}=50\\,\\Omega\\) by the matching relation above, then maximize \\(R_F\\) within the bandwidth/gain budget and choose the transistor sizes/bias for the highest practical \\(g_m\\), lowest \\(\\gamma\\), and favorable noise matching.  The final optimization is normally done with a noise simulation (noise circles) rather than by adjusting a single component.",
        "format": "markdown",
        "sha256": "4bbd095b1d172c40e1b67ed7ac2c08a03eeb4c897380efb632ded0971a2cae07"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It gives the correct finite-output-resistance matching relation, but it largely treats the match as fixing gm at 1/50 Ω and incorrectly calls 1+γ a lower bound. It does not clearly explain that gm can be raised above 1/Rs while increasing RF to preserve the match, allowing NF below 1+γ; its later claim about approaching unity is contradictory rather than a clear resolution.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 47621,
        "total_tokens": 48660,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 46427,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 47621,
        "total_tokens": 48660,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 46427,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Treat the 50 \\(\\Omega\\) input resistance as a **constraint**, not as the quantity to minimize. In this circuit the feedback resistor is mainly the matching element; once the transistor \\(g_m\\) and output resistance are chosen, \\(R_F\\) is fixed by the 50 \\(\\Omega\\) requirement. The noise figure is then minimized by changing the active devices/bias and by choosing a lower-noise allocation of \\(g_m\\), not by arbitrarily changing \\(R_F\\).\n\nFor a first-order design (ignore \\(C_1\\) and device capacitances at the operating frequency), let\n\n\\[\nG_m=g_{m1}+g_{m2},\\qquad \nR_o=r_{o1}\\parallel r_{o2}\\parallel R_L,\n\\]\n\nwhere \\(R_L\\) includes the output load. Then approximately\n\n\\[\nR_{\\rm in}\\approx \\frac{R_F+R_o}{1+G_m R_o}.\n\\]\n\nThus, to keep \\(R_{\\rm in}=R_s=50\\,\\Omega\\),\n\n\\[\n\\boxed{R_F=R_s(1+G_mR_o)-R_o}\n\\]\n\nor, for high gain \\(G_mR_o\\gg1\\),\n\n\\[\nR_F\\approx R_s(1+G_mR_o)\\approx R_sG_mR_o.\n\\]\n\nSo if you increase transistor width/current to improve noise, \\(g_m\\) changes; you must retune \\(R_F\\) according to this equation to keep the input at 50 \\(\\Omega\\).\n\nA useful low-frequency noise-factor expression for this shunt-feedback stage, including feedback-resistor and MOS channel thermal noise, is\n\n\\[\nF\n=\n1+\n\\frac{R_F}{R_s}\n\\frac{(1+G_mR_s)^2}{(G_mR_F-1)^2}\n+\n\\frac{\\Gamma}{R_s}\n\\frac{(R_F+R_s)^2}{(G_mR_F-1)^2},\n\\]\n\nwhere\n\n\\[\n\\Gamma=\\gamma_n g_{m1}+\\gamma_p g_{m2}\n\\]\n\n(plus the conductance of any physical load resistor whose noise is to be included), and\n\n\\[\nNF=10\\log_{10}F.\n\\]\n\nIn the usual high-gain, matched case this reduces approximately to\n\n\\[\nF\\simeq 1+\\frac{R_s}{R_F}+\\frac{\\gamma_{\\rm eff}}{G_mR_s}\n\\simeq\n1+\\frac{1}{G_mR_o}+\\frac{\\gamma_{\\rm eff}}{G_mR_s},\n\\]\n\nwith \\(\\gamma_{\\rm eff}=(\\gamma_n g_{m1}+\\gamma_p g_{m2})/G_m\\). This shows the main design directions:\n\n1. **Increase the loop gain \\(G_mR_o\\).**  \n   Larger total transconductance and larger output resistance lower the noise contribution of both the feedback resistor and the channel noise. In practice this means more bias current, better \\(g_m/I_D\\) (moderate/weak inversion as allowed by bandwidth), and longer channels/higher \\(r_o\\) if the resulting capacitance and \\(f_T\\) are acceptable.\n\n2. **Minimize the weighted channel-noise contribution.**  \n   Because \\(M_1\\) and \\(M_2\\) share the same node, the matching depends on \\(G_m=g_{m1}+g_{m2}\\), while the noise depends on \\(\\gamma_ng_{m1}+\\gamma_pg_{m2}\\). Therefore do not simply make the inverter geometrically symmetric; choose \\(W_n/L_n\\) and \\(W_p/L_p\\) so that most of the needed transconductance comes from the device with the lower effective \\(\\gamma\\), while still keeping both devices saturated and preserving the required dc bias.\n\n3. **Use \\(R_F\\) only as the matching control.**  \n   After changing \\(W\\) or bias, recalculate \\(R_F\\) from\n   \\[\n   R_F=R_s(1+G_mR_o)-R_o.\n   \\]\n   If the required \\(R_F\\) becomes negative or unrealistically large, the chosen \\(g_m\\)/load cannot be matched to 50 \\(\\Omega\\). If \\(R_F\\) alone is allowed to vary, there is no remaining degree of freedom under the exact 50 \\(\\Omega\\) constraint.\n\n4. **At RF, include \\(C_{gs}\\), gate resistance, and induced-gate noise.**  \n   Then use the two-port noise parameters:\n   \\[\n   F=F_{\\min}\n   +\\frac{R_n}{G_s}|Y_s-Y_{\\rm opt}|^2 .\n   \\]\n   For a fixed source admittance \\(Y_s=1/50\\), the lowest NF is obtained when the noise-optimum admittance presented to the active device is made equal to \\(1/50\\), while the input matching network/feedback makes the input admittance seen by the source also \\(1/50\\). In this simple feedback inverter this is generally done by sweeping transistor widths/bias in a simulator, with \\(R_F\\) adjusted at each point to satisfy\n   \\[\n   \\Re\\{Z_{\\rm in}(f_0)\\}=50\\,\\Omega,\\qquad\n   \\Im\\{Z_{\\rm in}(f_0)\\}=0.\n   \\]\n   If the topology does not have enough degrees of freedom, add a lossless input matching network, source degeneration, neutralization, gm-boosting, or use a differential/current-reused arrangement.\n\nPractical optimization procedure:\n\n- Fix \\(R_s=50\\,\\Omega\\), bias current/power, and operating frequency.\n- Sweep \\(W_n\\), \\(W_p\\), \\(L\\), and bias current.\n- For each point, set\n  \\[\n  R_F=R_s(1+G_mR_o)-R_o\n  \\]\n  or, more accurately, let the simulator/optimizer adjust \\(R_F\\) so that \\(Z_{\\rm in}(f_0)=50\\,\\Omega\\).\n- Minimize \\(NF(f_0)\\) subject to input match, gain, bandwidth, stability, and power constraints.\n- Keep \\(M_1,M_2\\) in saturation; use short gate fingers and proper layout to minimize gate resistance and parasitics.\n- Choose \\(C_1\\) large enough to be an RF short but not so large that start-up/low-frequency behavior is affected.\n\nBottom line: for a fixed 50 \\(\\Omega\\) input, the optimum is not found by tuning \\(R_F\\) alone. The correct approach is to maximize the permissible loop gain \\(G_mR_o\\), minimize the weighted channel-noise term \\(\\gamma_ng_{m1}+\\gamma_pg_{m2}\\), and then set \\(R_F\\) to restore \\(R_{\\rm in}=50\\,\\Omega\\). In a real RF design, do this together with full capacitance/inductance and induced-gate-noise models; the true minimum is usually found by a constrained noise optimization/simulation rather than by a single closed-form value.",
        "format": "markdown",
        "sha256": "0ae3a65b6fa4675b6cd977f63a770126c948066bd975928db886a7c48d129bec"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly uses the finite-output-resistance input-match relation and explains that gm can be increased while RF is retuned to keep Rin at 50 Ω, allowing NF to fall. The additional implementation and noise-model details do not undermine the central answer.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 37133,
        "total_tokens": 38172,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 37133,
        "total_tokens": 38172,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Use \\(R_{\\rm in}=50~\\Omega\\) as a constraint, not as the quantity to optimize. For the shunt-feedback inverter-style LNA in the figure, take the coupling capacitor \\(C_1\\) to be a short at the operating frequency. Define\n\n\\[\nR_S=50\\ \\Omega,\\qquad\nG_m=g_{m1}+g_{m2},\\qquad\nG_{ds}=g_{ds1}+g_{ds2}.\n\\]\n\nFor the low-frequency small-signal model,\n\n\\[\nR_{\\rm in}=\\frac{1+G_{ds}R_F}{G_m+G_{ds}} .\n\\]\n\nThus, once the transistor sizes and bias are chosen, the 50-\\(\\Omega\\) requirement fixes the feedback resistor:\n\n\\[\n\\boxed{R_F=\\frac{R_S(G_m+G_{ds})-1}{G_{ds}} }\n\\]\n\n(approximately \\(R_F\\approx(1+A_v)R_S\\) when the loop gain is high, with \\(A_v\\simeq G_m/G_{ds}\\)). Do not choose \\(R_F\\) independently for noise; it must satisfy this matching condition at the design frequency. If the transistor gates/parasitics make \\(R_{\\rm in}\\) complex, include the input capacitance and make the imaginary part zero with \\(C_1\\) or a lossless matching element.\n\nThe linear noise factor (ignoring induced gate noise and flicker noise) is approximately\n\n\\[\nF=1+\n\\frac{R_F}{R_S}\\frac{(1+G_mR_S)^2}{(G_mR_F-1)^2}\n+\n\\frac{\\gamma_n g_{m1}+\\gamma_p g_{m2}}{R_S}\n\\frac{(R_F+R_S)^2}{(G_mR_F-1)^2},\n\\]\n\nwhere \\(F=NF_{\\text{linear}}\\) and \\(NF_{\\rm dB}=10\\log_{10}F\\). For an active-load version where only \\(M_1\\) is driven by the input, replace \\(G_m\\) by \\(g_{m1}\\) in the signal-gain terms and keep the load noise term; for the inverter version shown, both devices contribute signal transconductance.\n\nUsing the matching condition, the design is optimized as follows:\n\n1. **Sweep transistor sizes and bias** (\\(W/L\\) of both devices and dc current). For each choice compute \\(g_m,g_{ds}\\), solve \\(R_F\\) from the 50-\\(\\Omega\\) equation, and evaluate \\(F\\). Choose the choice giving minimum \\(F\\) while still satisfying bandwidth, power, linearity and headroom.\n2. **Maximize useful loop gain/gm and minimize output conductance.** In the simple thermal-noise model, increasing \\(G_m\\) while adjusting \\(R_F\\) to keep \\(R_{\\rm in}=50~\\Omega\\) lowers the input-referred channel noise and also allows a larger, less-noisy feedback resistor. Increasing \\(G_m/G_{ds}\\) (higher intrinsic gain, longer channel, cascode, high-\\(r_o\\) load) reduces the noise floor caused by \\(R_F\\).\n3. **Keep the active load low-noise.** If \\(M_2\\) is only a current-source load, make its \\(g_m\\) (noise current) small while keeping its output resistance high; an ideal load adds no noise. Avoid adding series resistors. In an inverter, both devices provide signal gain, so use a proper PMOS/NMOS width ratio and bias so the total \\(g_m\\) per current is large and \\(\\gamma_n g_{m1}+\\gamma_p g_{m2}\\) is minimized.\n4. **At RF, use lossless noise matching.** Select device width/bias so that the optimum source impedance \\(Z_{\\rm opt}\\) of the input transistor is transformed to \\(50~\\Omega\\), while the input network still presents \\(50~\\Omega\\) to the source. In practice this is often done with a series gate inductor and source-degeneration inductor: set\n   \\[\n   \\Re\\{Z_{\\rm in}\\}=\\omega_T L_s=R_S,\n   \\]\n   and tune the imaginary part with a lossless element. This decouples the 50-\\(\\Omega\\) input match from the noise optimum much better than a purely resistive feedback network.\n5. Recheck the full circuit including \\(C_{gs}\\), Miller capacitance, \\(C_1\\), package/pad capacitance and inductor/capacitor \\(Q\\). At high frequency, solve the noise circles together with the input-match condition numerically; analytic low-frequency formulas are only a starting point.\n\nIn the ideal low-frequency thermal-noise model, the 50-\\(\\Omega\\) constraint alone does **not** give a finite optimum: \\(NF\\) decreases as \\(G_m\\) and \\(G_m/G_{ds}\\) are increased. Thus the practical optimum is usually at the maximum allowed gain/gm for the specified power or bandwidth. A useful rule of thumb for high loop gain is\n\n\\[\nF\\;\\approx\\;1+\\frac{1}{1+A_v}+\\frac{\\gamma}{G_mR_S},\n\\qquad A_v\\simeq \\frac{G_m}{G_{ds}},\n\\]\n\nso increase \\(A_v\\) and \\(G_mR_S\\) until bandwidth/power/headroom limits are reached, and keep the load and feedback-resistor noise as small as possible.",
        "format": "markdown",
        "sha256": "c5e3257fbc1d064b22fc75b250a88c4973b0b2af939d0ad0a8ef72f795157142"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It includes the finite-output-resistance input-match relation, shows how to adjust RF to keep Rin at 50 Ω, and correctly explains that gm can exceed 1/Rs so NF can fall below 1 + γ. The recommendation to raise gm while maintaining the match aligns with the golden solution.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 41101,
        "total_tokens": 42140,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35910,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1039,
        "output_tokens": 41101,
        "total_tokens": 42140,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 35910,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Let \\(P\\) be the input gate and let the open-loop voltage gain from \\(P\\) to \\(V_{\\rm out}\\) be  \n\\[\nA_v=\\frac{v_{\\rm out}}{v_P}<0 .\n\\]\nBecause the feedback is negative, write \\(A_v=-A\\), where \\(A>0\\) is the gain magnitude.\n\nApplying a small-signal test voltage \\(v_t\\) at the input,\n\\[\ni_t=sC_{\\rm in}v_t+\\frac{v_t-v_{\\rm out}}{R_F}.\n\\]\nUsing \\(v_{\\rm out}\\simeq -A v_t\\),\n\\[\ni_t=v_t\\left(sC_{\\rm in}+\\frac{1+A}{R_F}\\right),\n\\]\nso\n\\[\n\\boxed{\nZ_{\\rm in}(s)=\n\\left(sC_{\\rm in}+\\frac{1+A}{R_F}\\right)^{-1}\n= \\frac{R_F}{1+A}\\;\\middle\\|\\;\\frac{1}{sC_{\\rm in}} .\n}\n\\]\nThus the low-frequency input resistance is\n\\[\n\\boxed{R_{\\rm in}\\approx \\frac{R_F}{1+A}}.\n\\]\n\nFor the circuit shown, neglecting channel-length modulation and assuming the PMOS pair \\(M_2,M_3\\) is matched with an ideal tail current \\(I_{SS}\\),\n\\[\nA\\approx\n\\left(g_{m1}R_{D1}\\right)\n\\left(\\frac{g_{m2}R_{D2}}{2}\\right)\n=\n\\frac{1}{2}g_{m1}g_{m2}R_{D1}R_{D2},\n\\]\nso\n\\[\n\\boxed{\nR_{\\rm in}\\approx\n\\frac{R_F}\n{1+\\frac{1}{2}g_{m1}g_{m2}R_{D1}R_{D2}}\n}\n\\]\nand\n\\[\n\\boxed{\nZ_{\\rm in}(s)\\approx\n\\left[\nsC_{\\rm in}\n+\n\\frac{1+\\frac{1}{2}g_{m1}g_{m2}R_{D1}R_{D2}}\n{R_F}\n\\right]^{-1}.\n}\n\\]\n\nIf \\(r_o\\) is included, replace \\(R_{D1}\\) by \\(R_{D1}\\parallel r_{o1}\\) and, for a matched \\(M_2/M_3\\) pair, \\(R_{D2}\\) by \\(R_{D2}\\parallel 2r_o\\) in the gain expression. If the question asks only for the impedance looking into the amplifier (excluding the source capacitance \\(C_{\\rm in}\\)), omit the \\(sC_{\\rm in}\\) term.",
        "format": "markdown",
        "sha256": "f9c65c0d8b4ca4af08ad47f04b0723322287598d67a9e3a083c1fa2ceffa545b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies the negative-feedback Miller reduction and gives the appropriate unloaded gain, but misses the exact output-side resistance term: the input resistance is (RF + RD2)/(1 + A0), not RF/(1 + A0).",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 38336,
        "total_tokens": 38577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 38332,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 38336,
        "total_tokens": 38577,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 38332,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Let \\(g_{mi}\\) be the small-signal transconductance of transistor \\(M_i\\), and neglect channel-length modulation/body effect for the usual hand calculation. The amplifier has negative shunt feedback through \\(R_F\\).\n\nAt the input node \\(P\\), the first stage gives\n\\[\nv_x=-g_{m1}R_{D1}v_P .\n\\]\nThe \\(M_2\\)-\\(M_3\\) differential pair (with an ideal tail current source) has an effective transconductance from \\(X\\) to the output current\n\\[\nG_{m,\\text{diff}}=\\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}} .\n\\]\nThus the short-circuit output current produced by the second stage is\n\\[\ni_o=-G\\,v_P,\\qquad\nG=g_{m1}R_{D1}G_{m,\\text{diff}}\n= g_{m1}R_{D1}\\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}} .\n\\]\n\nUsing KCL at the output node,\n\\[\n-Gv_P=\\frac{v_o}{R_{D2}}+\\frac{v_o-v_P}{R_F},\n\\]\nand at the input node the current supplied is\n\\[\nI_{in}=\\frac{v_P-v_o}{R_F}.\n\\]\nSolving gives the low-frequency input resistance\n\\[\n\\boxed{\nR_{in}=\\frac{R_F+R_{D2}}\n{1+g_{m1}R_{D1}R_{D2}\\dfrac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}}\n}\n\\]\nfor \\(r_o\\to\\infty\\).\n\nIf \\(M_2\\) and \\(M_3\\) are matched and equally biased, \\(g_{m2}=g_{m3}=g_{mp}\\), so\n\\[\n\\boxed{\nR_{in}=\n\\frac{R_F+R_{D2}}\n{1+\\frac{1}{2}g_{m1}g_{mp}R_{D1}R_{D2}}\n}\n\\]\nand, for large loop gain or \\(R_F\\gg R_{D2}\\),\n\\[\n\\boxed{\nR_{in}\\approx\n\\frac{R_F}\n{1+\\frac{1}{2}g_{m1}g_{mp}R_{D1}R_{D2}}\n}\n\\]\nfor the matched case.\n\nIncluding the input capacitance shown, the total impedance at \\(P\\) is\n\\[\n\\boxed{\nZ_{in}(s)=R_{in}\\parallel \\frac{1}{sC_{in}}\n=\\frac{R_{in}}{1+sR_{in}C_{in}} .\n}\n\\]\n\nWith finite output resistances, replace \\(R_{D2}\\) by the output resistance of the amplifier seen at \\(V_{out}\\) with \\(R_F\\) removed and use the corresponding short-circuit transconductance; in the common case \\(r_{o}\\to\\infty\\), the boxed expression above is the standard result. The forward voltage gain is inverting; its magnitude is the loop-gain factor in the denominator.",
        "format": "markdown",
        "sha256": "240493540727a4c618084a12e36bff49d2bf8c3299f527ca7feb901a3f57f5eb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It gives the exact required result, \\(R_{in}=(R_F+R_{D2})/(1+A_0)\\), and its matched-pair expression for \\(A_0\\) agrees with the golden solution. The extra impedance discussion does not alter the correct answer.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 41743,
        "total_tokens": 41984,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41096,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 41743,
        "total_tokens": 41984,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 41096,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Neglecting channel-length modulation and transistor capacitances, and assuming the drain of \\(M_2\\) is tied to node \\(X\\) (diode-connected, as drawn), define\n\n\\[\ng_{\\rm eff}=\\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}} .\n\\]\n\nThe open-loop small-signal voltage gain from \\(P\\) to \\(V_{\\rm out}\\) is\n\n\\[\nA_v=\\left.\\frac{v_{\\rm out}}{v_P}\\right|_{R_F\\to\\infty}\n=\n-\\frac{g_{m1}R_{D1}\\,g_{\\rm eff}R_{D2}}{1+g_{\\rm eff}R_{D1}} .\n\\]\n\nWith the shunt feedback resistor \\(R_F\\) and output resistance \\(R_o\\simeq R_{D2}\\), the low-frequency active input resistance is\n\n\\[\n\\boxed{\nR_{\\rm in}\n=\n\\frac{R_F+R_{D2}}{1- A_v}\n=\n\\frac{R_F+R_{D2}}\n{1+\\dfrac{g_{m1}R_{D1}g_{\\rm eff}R_{D2}}{1+g_{\\rm eff}R_{D1}}}\n}\n\\]\n\nor, equivalently,\n\n\\[\n\\boxed{\nR_{\\rm in}\n=\n(R_F+R_{D2})\\,\n\\frac{1+g_{\\rm eff}R_{D1}}\n{1+g_{\\rm eff}R_{D1}+g_{m1}R_{D1}g_{\\rm eff}R_{D2}}\n}\n\\]\n\nwith\n\\[\ng_{\\rm eff}=\\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}.\n\\]\n\nThe total input impedance, including the input capacitor \\(C_{\\rm in}\\), is\n\n\\[\n\\boxed{\nZ_{\\rm in}(s)\n=\nR_{\\rm in}\\parallel \\frac{1}{sC_{\\rm in}}\n=\n\\left(\nsC_{\\rm in}\n+\n\\frac{1+|A_v|}{R_F+R_{D2}}\n\\right)^{-1},\n\\qquad s=j\\omega .\n}\n\\]\n\nFor \\(g_{m2}=g_{m3}=g_m\\), this becomes\n\n\\[\n|A_v|\n=\n\\frac{g_{m1}R_{D1}\\,g_mR_{D2}}\n{2+g_mR_{D1}},\n\\qquad\nR_{\\rm in}\n=\n\\frac{R_F+R_{D2}}\n{1+\\dfrac{g_{m1}R_{D1}g_mR_{D2}}{2+g_mR_{D1}}}.\n\\]\n\nIn the usual high-gain approximation \\(g_mR_{D1}\\gg2\\) and \\(g_{m1}R_{D2}\\gg1\\),\n\n\\[\n\\boxed{\nR_{\\rm in}\\approx \\frac{R_F}{1+g_{m1}R_{D2}},\n\\qquad\nZ_{\\rm in}\\approx\n\\left(\nsC_{\\rm in}\n+\n\\frac{1+g_{m1}R_{D2}}{R_F}\n\\right)^{-1}.\n}\n\\]\n\nIf the question asks only for the input resistance looking into the amplifier, use the \\(R_{\\rm in}\\) expression above; include \\(C_{\\rm in}\\) only when the total input impedance at the source node is required.",
        "format": "markdown",
        "sha256": "91c7d9e02c27ac6e4baa2571f77fc1aa19f8ccc98592b7304f11f6d1116a59f4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It uses the correct Miller-form structure and retains the output resistance, but its assumed device model adds an extra factor of 1 + g_eff R_D1 to the gain. The required unloaded gain is A0 = (1/2)g_m1 g_m2,3 R_D1 R_D2, so the central input-resistance result and high-gain approximation are incorrect.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 57276,
        "total_tokens": 57517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 56612,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 241,
        "output_tokens": 57276,
        "total_tokens": 57517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 56612,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "You cannot get the VCO phase noise from the LDO noise spectrum \\(S_{th}\\) alone; you also need the transfer from the LDO output voltage to the VCO instantaneous frequency, i.e. the VCO supply-pushing coefficient.\n\nLet \\(v_n(t)\\) be the LDO output noise at the VCO supply. For small perturbations,\n\n\\[\nf_{\\rm osc}(t)=f_0 + K_{\\rm push}\\,v_n(t),\n\\qquad\nK_{\\rm push}\\equiv \\left.\\frac{\\partial f_{\\rm osc}}{\\partial V_{\\rm DD}}\\right|_{V_{\\rm cont}}\n\\quad [\\mathrm{Hz/V}].\n\\]\n\nThe phase is \\(\\phi(t)=2\\pi\\int (f_{\\rm osc}-f_0)\\,dt\\), so in the frequency domain the voltage-to-phase transfer is\n\n\\[\nH_{\\phi,V_{\\rm DD}}(f_m)=\\frac{K_{\\rm push}}{j f_m}\n\\]\n\nfor low modulation frequencies compared with the carrier. Therefore, using one-sided PSDs,\n\n\\[\n\\boxed{\nS_{\\phi,\\mathrm{LDO}}(f_m)\n=\n\\frac{K_{\\rm push}^{\\,2}}{f_m^{2}}\\,\nS_{V,\\mathrm{LDO}}(f_m)\n\\quad [\\mathrm{rad^2/Hz}]\n}\n\\]\n\nand the single-sideband phase-noise contribution is\n\n\\[\n\\boxed{\n\\mathcal L_{\\mathrm{LDO}}(f_m)\n=\n10\\log_{10}\\!\\left[\n\\frac{K_{\\rm push}^{\\,2}\\,S_{V,\\mathrm{LDO}}(f_m)}\n     {2 f_m^{2}}\n\\right]\n\\ \\mathrm{dBc/Hz}\n}\n\\]\n\nwhere \\(S_{V,\\mathrm{LDO}}(f_m)\\) is the LDO output-noise PSD at the offset frequency \\(f_m\\). If \\(S_{th}\\) is already the one-sided LDO output voltage-noise PSD, set \\(S_{V,\\mathrm{LDO}}(f_m)=S_{th}(f_m)\\). The factor \\(1/2\\) comes from the definition of single-sideband phase noise; with two-sided PSDs, use the same convention consistently.\n\nFor white thermal noise, \\(S_{th}\\) is approximately constant, so\n\n\\[\nS_{\\phi,\\mathrm{LDO}}(f_m)\\propto \\frac{1}{f_m^{2}},\n\\qquad\n\\mathcal L_{\\mathrm{LDO}}(f_m)\\sim -20\\ \\mathrm{dB/dec}.\n\\]\n\nIf a frequency-dependent pushing coefficient \\(K_{\\rm push}(f_m)\\) is available, replace \\(K_{\\rm push}\\) by \\(K_{\\rm push}(f_m)\\). More generally, replace \\(K_{\\rm push}/(j f_m)\\) by the full small-signal transfer \\(H_{\\phi,V_{\\rm DD}}(f_m)\\) from the LDO output to oscillator phase, obtained from PSS+PAC/PXF or PSS+Pnoise in a circuit simulator or measured.\n\nFor the varactor-tuned LC VCO shown, a useful estimate is\n\n\\[\nK_{\\rm push}\n\\simeq\n-\\frac{f_0}{2C_{\\rm eq}}\n\\frac{\\partial C_{\\rm eq}}{\\partial V_{\\rm DD}},\n\\qquad\nf_0=\\frac{1}{2\\pi\\sqrt{L C_{\\rm eq}}},\n\\]\n\nwhere \\(C_{\\rm eq}\\) is the effective tank capacitance including varactors and parasitics. As drawn, the varactor bias is essentially \\(V_{\\rm DD}-V_{\\rm cont}\\), so if the only supply sensitivity is through the varactor bias,\n\n\\[\nK_{\\rm push}\\approx -K_{\\rm VCO},\n\\qquad\nK_{\\rm VCO}=\\frac{\\partial f_0}{\\partial V_{\\rm cont}}.\n\\]\n\nThe sign does not matter for the PSD. If \\(V_{\\rm cont}\\) is also noisy, use the equivalent bias noise \\(v_{\\rm DD}-v_{\\rm cont}\\) and add the contributions coherently.\n\nIn an ideally symmetric differential VCO, a purely common-mode supply perturbation is rejected to first order; realistic supply pushing comes from varactor bias dependence, nonlinear capacitances, mismatch, finite current-source output impedance, etc. Thus \\(K_{\\rm push}\\) should include the actual circuit effects or be simulated.\n\nFinally, the LDO contribution is added in power to the intrinsic VCO phase noise and other noise sources:\n\n\\[\nS_{\\phi,\\mathrm{tot}}=\nS_{\\phi,\\mathrm{intrinsic}}+\nS_{\\phi,\\mathrm{LDO}}+\\cdots,\n\\]\n\n\\[\n\\mathcal L_{\\mathrm{tot}}\n=\n10\\log_{10}\\!\\left(\n10^{\\mathcal L_{\\mathrm{intrinsic}}/10}\n+\n10^{\\mathcal L_{\\mathrm{LDO}}/10}\n+\\cdots\n\\right).\n\\]\n\nFor accurate high-offset or strongly nonlinear cases, do not use the quasi-static pushing formula alone; run a periodic steady-state plus periodic-noise analysis with the LDO noise source included.",
        "format": "markdown",
        "sha256": "37fc4d1cbe4cd1027a642dfe126c167fb5959efa328d18947ab746643834fc6f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly converts LDO voltage-noise PSD through the supply-pushing sensitivity to phase noise with the required 1/f_m^2 dependence, gives the SSB relation, and captures the varactor/KVCO design insight. Extra simulation and noise-combination details do not undermine the answer.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 22638,
        "total_tokens": 23640,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21618,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 22638,
        "total_tokens": 23640,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 21618,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The LDO noise density alone does not determine the VCO phase noise; you also need the transfer from the LDO output node to the oscillator phase. The usual small-noise calculation is:\n\nLet\n\n- \\(v_{n}(t)\\) be the small noise voltage at the VCO supply rail after the LDO, with one-sided voltage noise PSD  \n  \\[\n  S_{V_{DD}}(f)\\quad [\\mathrm{V^2/Hz}]\n  \\]\n  (if the LDO spec is already the output-noise PSD, \\(S_{V_{DD}}=S_{\\rm th}\\); otherwise include the LDO output/decoupling transfer to the VCO rail),\n- \\(K_{V_{DD}}\\) be the VCO supply-pushing gain\n  \\[\n  K_{V_{DD}}=\\frac{\\partial f_{\\rm osc}}{\\partial V_{DD}}\\quad [\\mathrm{Hz/V}]\n  \\]\n  or, more generally, the small-signal transfer from a sinusoidal \\(V_{DD}\\) perturbation at offset \\(f_m\\) to the VCO instantaneous frequency, \\(K_{V_{DD}}(f_m)\\).\n\nThe supply noise frequency-modulates the oscillator:\n\\[\n\\delta f(t)=K_{V_{DD}}v_n(t),\n\\]\nso the instantaneous-frequency noise PSD is\n\\[\nS_f(f_m)=|K_{V_{DD}}(f_m)|^2 S_{V_{DD}}(f_m).\n\\]\nSince phase is the integral of frequency,\n\\[\nS_\\phi(f_m)=\\frac{S_f(f_m)}{f_m^2}\n       =\\frac{|K_{V_{DD}}(f_m)|^2 S_{V_{DD}}(f_m)}{f_m^2}.\n\\]\nThe single-sideband phase noise (relative to carrier) is therefore\n\\[\n\\boxed{\n\\mathcal L(f_m)\n=\\frac12 S_\\phi(f_m)\n=\\frac{|K_{V_{DD}}(f_m)|^2 S_{V_{DD}}(f_m)}{2f_m^2}\n}\n\\]\nfor a one-sided PSD. In dBc/Hz,\n\\[\n\\mathcal L_{\\rm dBc/Hz}(f_m)\n=10\\log_{10}\\!\\left[\n\\frac{|K_{V_{DD}}(f_m)|^2 S_{V_{DD}}(f_m)}{2f_m^2}\n\\right].\n\\]\nIf the LDO thermal noise is white over the offset of interest and \\(K_{V_{DD}}\\) is approximately constant, set \\(S_{V_{DD}}(f_m)=S_{\\rm th}\\):\n\\[\n\\boxed{\n\\mathcal L(f_m)\\approx \\frac{K_{V_{DD}}^2 S_{\\rm th}}{2f_m^2}\n}\n\\]\nso a white thermal noise gives a \\(1/f_m^2\\) phase-noise contribution. Any LDO flicker noise would give a \\(1/f_m^3\\) contribution.\n\nFor this specific VCO, \\(K_{V_{DD}}\\) is found from the actual supply-to-frequency conversion, including the varactor bias, capacitor banks, parasitic capacitances, core nonlinearity, etc. A rough small-signal estimate is\n\\[\nK_{V_{DD}}\n=-\\frac{f_0}{2C_{\\rm eff}}\\frac{\\partial C_{\\rm eff}}{\\partial V_{DD}},\n\\]\nwhere \\(C_{\\rm eff}\\) is the effective tank capacitance seen by the differential mode. The varactors are usually the main path: for an ideal varactor biased by approximately \\(V_{DD}-V_{cont}\\), changing \\(V_{DD}\\) is equivalent to changing \\(V_{cont}\\) with opposite sign, so\n\\[\n|K_{V_{DD}}|\\approx |K_{VCO}|\n=\\left|\\frac{\\partial f_0}{\\partial V_{cont}}\\right|\n\\]\nwhen the only relevant path is the varactor and \\(V_{cont}\\) is ground-referenced. If \\(V_{cont}\\) also tracks the LDO rail, use the net variation of \\(V_{DD}-V_{cont}\\), since the two may cancel.\n\nIn practice, the most reliable way to get \\(K_{V_{DD}}(f_m)\\) or the full phase transfer \\(H_{\\phi,V_{DD}}(f_m)\\) is to simulate the oscillator with a small-signal supply excitation: PSS plus PXF/pnoise or a small injected tone at \\(V_{DD}\\) and measurement of the resulting sidebands. Then\n\\[\n\\mathcal L(f_m)=\\frac12 |H_{\\phi,V_{DD}}(f_m)|^2 S_{V_{DD}}(f_m),\n\\]\nwith \\(H_{\\phi,V_{DD}}\\approx K_{V_{DD}}/f_m\\) in the quasi-static/low-offset limit. This automatically includes nonlinear varactor effects, common-mode-to-frequency conversion, AM-to-PM conversion, and mismatch.\n\nFinally, the LDO rail noise is normally common-mode at the differential output. In an ideal symmetric differential oscillator with zero supply pushing, the LDO noise produces no differential phase noise. In the real circuit, the nonlinear varactors and other device capacitances give a finite \\(K_{V_{DD}}\\), so the above expression applies. The total phase noise is the sum of uncorrelated contributions:\n\\[\n\\mathcal L_{\\rm tot}(f_m)\n=\n\\mathcal L_{\\rm intrinsic}(f_m)\n+\n\\mathcal L_{\\rm LDO}(f_m)\n+\\cdots\n\\]\n(using the same one-sided/two-sided PSD convention throughout).",
        "format": "markdown",
        "sha256": "f43d5c877dddf82e10773e010cab49c90d4b8a65c9573ee161c8762ae0f021e8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing, converts LDO noise through the supply-to-frequency sensitivity, and applies the 1/Δf² FM-to-phase-noise relation. It also notes the direct varactor path makes the sensitivity closely related to KVCO; PSD-convention details are secondary.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 32237,
        "total_tokens": 33239,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31094,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 32237,
        "total_tokens": 33239,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 31094,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "You need more than \\(S_{th}\\) alone: you need the VCO’s supply-to-frequency conversion gain (supply pushing), plus any filtering between the LDO and the VCO supply.\n\nFor the free-running VCO shown, the LDO noise at \\(V_{\\rm out}\\) is mostly common-mode on the tank nodes \\(X,Y\\). It changes the varactor bias approximately as \\(V_X-V_{\\rm cont}\\approx V_{\\rm out}-V_{\\rm cont}\\), and also changes parasitic MOS/junction capacitances. Hence it frequency-modulates the oscillator.\n\nDefine the supply pushing coefficient at the operating point as\n\n\\[\nK_{\\rm push}=\\frac{\\partial f_0}{\\partial V_{\\rm DD}}\n\\quad [\\mathrm{Hz/V}],\n\\qquad\nK_\\omega=\\frac{\\partial \\omega_0}{\\partial V_{\\rm DD}}\n=2\\pi K_{\\rm push}\n\\quad [\\mathrm{rad/s/V}].\n\\]\n\nFor an LC tank this is approximately\n\n\\[\nK_{\\rm push}\n= -\\frac{f_0}{2C_{\\rm tank}(V_{\\rm DD})}\n  \\frac{\\partial C_{\\rm tank}}{\\partial V_{\\rm DD}},\n\\]\n\nwhere \\(C_{\\rm tank}\\) includes the varactors and all supply-dependent parasitic capacitances. In practice, the most reliable way to get it is a periodic steady-state simulation while sweeping the supply voltage by a small amount.\n\nLet \\(S_{v_{dd}}(f_m)\\) be the one-sided noise PSD at the VCO supply, in \\(\\mathrm{V^2/Hz}\\), at offset \\(f_m\\) from the carrier. If the LDO is ideal-connected directly to the VCO and no filtering is included, then\n\n\\[\nS_{v_{dd}}(f_m)=S_{th}(f_m).\n\\]\n\nIf the LDO data sheet gives an amplitude noise density \\(e_n\\) in \\(\\mathrm{V/\\sqrt{Hz}}\\), then use \\(S_{th}=e_n^2\\).\n\nThe supply noise produces instantaneous frequency deviation\n\n\\[\nf_{\\rm inst}(t)=f_0+K_{\\rm push}\\,v_{dd}(t),\n\\]\n\nand the phase is the integral of the frequency error:\n\n\\[\n\\phi(t)=2\\pi K_{\\rm push}\\int v_{dd}(t)\\,dt.\n\\]\n\nThus, at offset \\(f_m\\), with \\(S_{v_{dd}}\\) one-sided,\n\n\\[\nS_\\phi(f_m)=\\left(\\frac{K_{\\rm push}}{f_m}\\right)^2\nS_{v_{dd}}(f_m)\n\\quad [\\mathrm{rad^2/Hz}],\n\\]\n\nand the single-sideband phase-noise spectrum is\n\n\\[\n\\boxed{\n\\mathcal L_{\\rm LDO}(f_m)\n=\n\\frac{1}{2}\n\\left(\\frac{K_{\\rm push}}{f_m}\\right)^2\nS_{v_{dd}}(f_m)\n}\n\\]\n\nwhere \\(\\mathcal L\\) is a linear power ratio per Hz. In dBc/Hz:\n\n\\[\n\\boxed{\n\\mathcal L_{\\rm LDO,dB}(f_m)\n=\n10\\log_{10}\\!\\left[\n\\frac{K_{\\rm push}^2\\,S_{v_{dd}}(f_m)}\n     {2 f_m^2}\n\\right]\n}\n\\]\n\nEquivalently, using \\(K_\\omega\\) in \\(\\mathrm{rad/s/V}\\),\n\n\\[\n\\mathcal L_{\\rm LDO}(f_m)\n=\n\\frac{K_\\omega^2}{8\\pi^2 f_m^2}\nS_{v_{dd}}(f_m)\n=\n\\frac{K_\\omega^2}{2(2\\pi f_m)^2}\nS_{v_{dd}}(f_m).\n\\]\n\nFor pure white thermal LDO noise, \\(S_{v_{dd}}\\) is roughly constant, so the LDO contribution to phase noise falls as\n\n\\[\n\\mathcal L_{\\rm LDO}(f_m)\\propto \\frac{1}{f_m^2},\n\\]\n\ni.e. \\(-20\\,\\mathrm{dB/decade}\\). If the LDO noise also has a \\(1/f\\) flicker component, insert the actual frequency-dependent \\(S_{v_{dd}}(f_m)\\); the flicker part produces a \\(1/f_m^3\\) contribution.\n\nFor a more exact calculation:\n\n- Replace \\(S_{th}\\) by the noise actually reaching the VCO supply:\n  \\[\n  S_{v_{dd}}(f_m)=|H_{\\rm LDO\\to VCO}(f_m)|^2 S_{th}(f_m),\n  \\]\n  where \\(H\\) includes the LDO output impedance, output capacitor, package inductance, on-chip decoupling, etc.\n- Use a periodic small-signal noise analysis (PSS + pnoise) or impulse-sensitivity-function analysis to obtain the full voltage-noise-to-phase transfer:\n  \\[\n  S_\\phi(f_m)=|H_{\\phi,V_{\\rm DD}}(f_m)|^2 S_{v_{dd}}(f_m),\n  \\qquad\n  \\mathcal L=\\frac{1}{2}S_\\phi,\n  \\]\n  using a one-sided \\(S_\\phi\\). This automatically includes high-frequency folding and finite tank bandwidth. The simple \\(K_{\\rm push}\\) formula above is the low-frequency/adiabatic approximation and is usually accurate for offsets well below \\(f_0\\) and below the LDO/decoupling bandwidth.\n- If the LDO noise reaches other bias/control nodes, combine the paths coherently before squaring. For example, if \\(V_{\\rm cont}\\) also moves with the LDO,\n  \\[\n  K_{\\rm eff}(f_m)\n  =\n  K_{V_{\\rm DD}}H_{V_{\\rm DD}}(f_m)\n  +\n  K_{V_{\\rm cont}}H_{V_{\\rm cont}}(f_m)+\\cdots,\n  \\]\n  then use \\(|K_{\\rm eff}|^2/f_m^2\\) in the phase-noise formula. In the schematic, if \\(V_{\\rm cont}\\) is ground-referenced, LDO noise changes \\(V_{\\rm DD}-V_{\\rm cont}\\); if \\(V_{\\rm cont}\\) is generated from the same LDO and tracks \\(V_{\\rm DD}\\), the common-mode effect can be strongly rejected.\n\nFinally, add this contribution to the intrinsic VCO phase noise in linear power, not directly in dB:\n\n\\[\n\\mathcal L_{\\rm total}\n=\n\\mathcal L_{\\rm VCO,intrinsic}\n+\n\\mathcal L_{\\rm LDO}\n+\\cdots .\n\\]\n\nThe factor of \\(1/2\\) depends on convention. If a paper defines the phase PSD as two-sided and writes \\(\\mathcal L=S_\\phi\\) for positive offsets, the \\(1/2\\) is absorbed into that definition; with a two-sided supply-noise PSD at positive frequency, the single-sideband result corresponds to \\(K_f^2S_{v_{dd}}^{\\rm 2-sided}/f_m^2\\).",
        "format": "markdown",
        "sha256": "1980db397ebc77a3cf4b3150171bfaa1801834cf7f4cdbe5b54a9824a8687b75"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies supply pushing and gives the appropriate FM-to-phase-noise conversion, including the 1/f_m^2 dependence and valid PSD conventions. It notes direct varactor modulation but omits the stated design insight that Kpush is closely related to KVCO and that reducing KVCO reduces this noise contribution.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 28340,
        "total_tokens": 29342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26909,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1002,
        "output_tokens": 28340,
        "total_tokens": 29342,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26909,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Adding \\(C_T\\) at the tail/common-source node normally **improves (reduces) the phase noise**, especially the contribution from the tail current source and even-order nonlinearity.\n\nReason: at the oscillation frequency \\(\\omega_0\\), the tail node \\(P\\) is a virtual ground for the differential signal, so an ideal \\(C_T\\) does not load/detune the differential tank. However, at \\(2\\omega_0\\) (and other even harmonics) \\(P\\) is not a virtual ground. Noise from the tail current source and even-harmonic currents/voltages there can be mixed by the nonlinear cross-coupled pair into sidebands around \\(\\omega_0\\), i.e. phase noise. \\(C_T\\) shunts these currents and makes \\(P\\) a low-impedance AC ground, suppressing the up/down-conversion. It can also push the core toward a class-C-like, narrower conduction-angle operation, reducing noise injection from the devices.\n\nIn an ideal, perfectly balanced, noiseless circuit an ideal capacitor has no first-order effect. In practice the improvement is not necessarily monotonic: tail parasitics (bond-wire/current-source inductance/capacitance) can resonate with \\(C_T\\), and if the tail impedance is made large near \\(2\\omega_0\\) instead of small, phase noise can worsen. Thus the useful bias is:\n\n\\[\n\\frac{1}{2\\omega_0 C_T}\\ll |Z_{\\text{tail}}|\n\\]\n\nso that the tail node is a low impedance at \\(2\\omega_0\\). With that condition, adding \\(C_T\\) lowers phase noise; too small a value has little effect, and a mistuned/large value with parasitics may create a resonance that degrades phase noise.",
        "format": "markdown",
        "sha256": "3dc03283c195c4a0093c8732596e7c348c68a40b2a281933fca4e263c040a9e6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It captures a nonmonotonic effect and identifies class-C-like operation as a possible improvement. However, it mainly attributes the benefit to shunting tail noise, omits the peak tank currents exceeding ISS mechanism, and gives a parasitic-resonance caveat rather than Razavi’s key degradation mechanisms.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 22765,
        "total_tokens": 23769,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22403,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 22765,
        "total_tokens": 23769,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 22403,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "With a properly chosen \\(C_T\\), the phase noise generally **improves (decreases)**.\n\nThe tail (common-source) node is not an ideal ground; because of the nonlinear switching of the cross-coupled pair it has a strong component at \\(2f_0\\). Adding \\(C_T\\):\n\n- Changes/terminates the tail-node impedance at even harmonics, reducing common-mode second-harmonic voltage and noise up-conversion.\n- Bypasses high-frequency noise from the tail current source \\(I_{SS}\\) to ground, so less of it is converted into differential-mode phase noise.\n- Shapes the conduction angle of \\(M_1,M_2\\) (class-C-like operation), so the devices are near/off around the tank-voltage zero crossings, where phase-noise sensitivity is maximum.\n\nHowever, \\(C_T\\) is not “the larger the better.” If \\(C_T\\) is too large or is not chosen together with the tail parasitics, it effectively shorts the tail node at \\(2f_0\\), removes the beneficial second-harmonic waveform, reduces the effective negative conductance/amplitude and can form an unwanted tail resonance. Then phase noise can increase or oscillation may start poorly.\n\nSo: **optimum \\(C_T\\) reduces phase noise; arbitrary/very large \\(C_T\\) may degrade it. Phase noise versus \\(C_T\\) normally has a minimum; simulate with actual parasitics/bias.**",
        "format": "markdown",
        "sha256": "6354dc6cb4d4177ad0366516ec04e348c76f7fd9e79a4e6d4139ac27f2850334"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly identifies an optimum/nonmonotonic effect and gives a class-C-like improvement mechanism. However, it omits the key peak-current-greater-than-ISS explanation and the specific degradations in the golden solution, substituting questionable tail-filtering and large-CT explanations.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 29164,
        "total_tokens": 30168,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28876,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 29164,
        "total_tokens": 30168,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 28876,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Adding \\(C_T\\) to the tail/common-source node normally **improves (reduces) the phase noise**, especially the contribution from the tail current source. In an ideal differential oscillator the tail node is a virtual ground at \\(f_0\\); the important unwanted component there is the second harmonic at \\(2f_0\\). The tail capacitor provides a low impedance at \\(2f_0\\), so the common-source voltage swing and the tail-current-source noise are shunted instead of being mixed/upconverted by the nonlinear transistor pair into phase noise. The ideal capacitor itself adds no noise.\n\nPractical caveats:\n- The effect is not without limit: \\(C_T\\) must be large enough to make the tail node a good short at \\(2f_0\\); an optimum value usually exists.\n- Too large a \\(C_T\\) gives little further improvement and can hurt the oscillator through parasitic common-mode loading, reduced headroom/amplitude/tuning range, mismatch, or a changed conduction angle.\n- In a perfectly ideal, perfectly symmetric oscillator with a noiseless tail source, the capacitor would not change the phase noise at all; the improvement comes from filtering real common-mode/second-harmonic noise and its upconversion.\n\nSo, in a normal design: **phase noise decreases (improves), particularly the tail-current-source contribution, if \\(C_T\\) is chosen correctly.**",
        "format": "markdown",
        "sha256": "9ca69ae8ee1101a1abf31cf22c7b56c24545c1b54efa18530d96765cb1bb3f21"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It mentions an optimum and generic downsides from excessive capacitance, but misses the key class-C current mechanism and Razavi’s specific phase-noise degradations. Its main explanation—that CT reduces phase noise by filtering tail-node ripple and tail-source noise—is not the essential result.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 25369,
        "total_tokens": 26373,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25088,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1004,
        "output_tokens": 25369,
        "total_tokens": 26373,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25088,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This is a quadrature LC oscillator: two identical cross-coupled LC tanks coupled to force a \\(90^\\circ\\) phase relation between \\((X_1,Y_1)\\) and \\((X_2,Y_2)\\).\n\nTo first order, the oscillation frequency is set by the resonance of each LC tank:\n\\[\n\\boxed{\\;f_{\\rm osc}\\approx \\frac{\\omega_0}{2\\pi}\n=\\frac{1}{2\\pi\\sqrt{L_{\\rm eff}C_{\\rm eff}}}\\;}\n\\]\nwhere \\(L_{\\rm eff}\\) and \\(C_{\\rm eff}\\) are the effective differential tank inductance and capacitance seen between the two output nodes of one oscillator, e.g. between \\(X_1\\) and \\(Y_1\\).\n\nFor the common case where each output has an inductor \\(L\\) connected to the ac-grounded supply rail, the differential tank inductance is\n\\[\nL_{\\rm eff}=2L .\n\\]\nIf each output node has total capacitance \\(C_n\\) to ground, the differential capacitance is \\(C_{\\rm eff}=C_n/2\\), so\n\\[\n\\boxed{f_{\\rm osc}\\approx \\frac{1}{2\\pi\\sqrt{L\\,C_n}}.}\n\\]\nEquivalently, with a total differential capacitance \\(C_d\\) between the two outputs,\n\\[\nf_{\\rm osc}\\approx \\frac{1}{2\\pi\\sqrt{(2L)C_d}}.\n\\]\n\nThe coupling transistors biased by \\(I_1\\) mainly enforce quadrature. They give only a small frequency shift:\n\\[\n\\omega_{\\rm osc}\\approx \\omega_0\\left[1\\mp \\frac{1}{2Q}\\frac{g_{m1}}{g_{m,SS}}\\right],\n\\]\nwhere \\(Q\\) is the tank quality factor, \\(g_{m,SS}\\) is set by \\(I_{SS}\\), and \\(g_{m1}\\) is set by \\(I_1\\). Often \\(I_1\\ll I_{SS}\\), so the simple estimate \\(f_{\\rm osc}\\approx 1/(2\\pi\\sqrt{L_{\\rm eff}C_{\\rm eff}})\\) is accurate.\n\nNo numerical frequency can be computed from the figure alone because the inductor values, tank capacitances, and transistor/process parasitics are not given.",
        "format": "markdown",
        "sha256": "c0322091d207cbfb330e4f0192c767bd993641d896ebf25b056f89fdcbf576b4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It gives the tank resonance and the required first-order coupling shift proportional to the coupling-to-core transconductance ratio over 2Q. The stated bias-current mapping makes its ratio equivalent to I1/ISS; the effective differential-tank details are ancillary.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 20577,
        "total_tokens": 21566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 20577,
        "total_tokens": 21566,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 20113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "For an ideal symmetric version of this circuit, the oscillation frequency is set by the LC tanks, not by the bias currents \\(I_{SS}\\) and \\(I_1\\). If each output node has inductance \\(L\\) to the supply and total capacitance \\(C\\) to ac ground,\n\n\\[\n\\boxed{\\;f_{\\rm osc}\\approx \\frac{1}{2\\pi\\sqrt{LC}}\\;}\n\\]\n\nor equivalently\n\n\\[\n\\omega_{\\rm osc}\\approx \\frac{1}{\\sqrt{LC}}.\n\\]\n\nHere \\(C\\) includes the transistor parasitics and any tank capacitance (none is drawn explicitly). The currents only control the negative conductance/coupling and hence whether oscillation starts and which coupled mode dominates; in the ideal model they do not shift the frequency.\n\nIn a more detailed coupled/quadrature-oscillator model, the coupling transistors introduce a small frequency pulling:\n\n\\[\nf_{\\rm osc}\\approx f_0\\left(1\\mp \\frac{1}{2Q}\\frac{g_{m1}}{g_{mSS}}\\right),\n\\qquad f_0=\\frac{1}{2\\pi\\sqrt{LC}},\n\\]\n\nwhere \\(Q\\) is the tank quality factor and \\(g_{m1}\\) is the transconductance of the coupling pair biased by \\(I_1\\). For identical square-law devices, \\(g_{m1}/g_{mSS}\\approx\\sqrt{I_1/I_{SS}}\\); in the fully switched limit, this ratio is approximately \\(I_1/I_{SS}\\).\n\nSo the leading-order estimate is the usual LC-tank resonance, with a small correction if the coupling strength is significant. A numerical value cannot be obtained without \\(L\\), \\(C\\), \\(Q\\), and device/bias data.",
        "format": "markdown",
        "sha256": "efbe4fb7357dbe71b3ea0264cc13c0fe302f094494da29df1d88c10982d8e269"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Gives the tank resonance and the correct first-order coupling-induced shift, with the coupling-to-core transconductance ratio and the fully switched current-ratio limit. The qualified statement that the ideal tank has no pulling does not undermine the included estimate.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 47883,
        "total_tokens": 48872,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 48699,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 47883,
        "total_tokens": 48872,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 48699,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "deepseek/deepseek-v4.1-flash-1017",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit is a pair of cross-coupled differential LC oscillators. Its oscillation frequency is set primarily by the resonant tank of each oscillator, not by the bias currents.\n\nFor one tank, to first order,\n\n\\[\nf_0 \\approx \\frac{1}{2\\pi\\sqrt{L_{\\rm eff}C_{\\rm eff}}}\n\\]\n\nwhere  \n\n- \\(L_{\\rm eff}\\) is the effective tank inductance,  \n- \\(C_{\\rm eff}\\) is the total effective capacitance across the tank, including MOS parasitics, varactors, and wiring capacitance.\n\nIf each drawn coil has inductance \\(L\\) from a tank node to the common ac ground, and \\(C_n\\) is the capacitance from each node to ground, then\n\n\\[\nf_0 \\approx \\frac{1}{2\\pi\\sqrt{L C_n}} .\n\\]\n\nAlternatively, using the differential tank inductance \\(L_{\\rm eff}=2L\\) and differential capacitance \\(C_{\\rm diff}\\) between the two nodes,\n\n\\[\nf_0 \\approx \\frac{1}{2\\pi\\sqrt{(2L)C_{\\rm diff}}} .\n\\]\n\nThe cross-coupled pair biased by \\(I_{SS}\\) supplies the negative resistance needed for oscillation. The extra cross-coupled pair biased by \\(I_1\\) couples the two oscillators; it can create two close supermodes and slightly pull the frequency through parasitics/nonlinearity, but the first-order frequency is still the LC resonance.\n\nA numerical value cannot be obtained from this schematic alone because no inductor, capacitor, transistor-size, or process values are shown. For typical integrated CMOS LC oscillators, this topology usually oscillates in the low-to-tens of GHz range. For example, with \\(L=1\\,\\mathrm{nH}\\) and \\(C=1\\,\\mathrm{pF}\\),\n\n\\[\nf_0 \\approx \\frac{1}{2\\pi\\sqrt{10^{-9}\\cdot10^{-12}}}\n\\approx 5.0\\ \\mathrm{GHz}.\n\\]\n\nSo the estimate is \\(f\\approx 1/(2\\pi\\sqrt{L_{\\rm eff}C_{\\rm eff}})\\); plugging in the actual tank inductance and capacitance gives the numerical oscillation frequency.",
        "format": "markdown",
        "sha256": "a034eee76d9fae6abc056eccd644a29ccf17ea3334bf9d6df3925e4ca394431f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The tank resonance estimate is correct and the answer recognizes that the extra pair couples the oscillators, but it omits the essential coupling-induced frequency shift, approximately Δω = αω₀/(2Q), and mischaracterizes the shift as arising through parasitics or nonlinearity.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 20301,
        "total_tokens": 21290,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19857,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 989,
        "output_tokens": 20301,
        "total_tokens": 21290,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19857,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    }
  ]
}
