{
  "model_key": "gpt_4o_2024_11_20",
  "display_name": "GPT-4o (2024-11-20)",
  "provider": "openai",
  "evaluation_model_ids": [],
  "thinking_effort": "default",
  "configuration_note": "GPT-4o (2024-11-20) answered the 50 tasks in three rollouts through OpenRouter's chat completions route (openai/gpt-4o-2024-11-20) without reasoning (the model has no reasoning setting). Requests set temperature to 0 and max_tokens to 16,384, the model's output limit. Each request was one user message holding only the question text and its figure: no title, headings or system prompt. Answers cut off at the output limit were re-run; every attempt is counted in tokens and cost. Answers were graded by GPT-6 Luna at maximum reasoning effort. Cost uses OpenRouter's list price for GPT-4o (2024-11-20) on 2026-11-10 ($2.50 input, $1.25 cached input, $10.00 output per 1M tokens).",
  "mode": "direct_qa",
  "summary": {
    "rollout_count": 3,
    "answer_count": 150,
    "scores": {
      "overall": {
        "gpt_6_luna_max": {
          "response_count": 150,
          "correct_count": 12,
          "incorrect_count": 138,
          "partial_credit_count": 86,
          "zero_count": 52,
          "mean_score_0_to_4": 1.2666666666666666,
          "score_percent": 31.666666666666664,
          "score_distribution": {
            "0": 52,
            "1": 48,
            "2": 20,
            "3": 18,
            "4": 12
          }
        },
        "active": {
          "response_count": 150,
          "correct_count": 12,
          "incorrect_count": 138,
          "partial_credit_count": 86,
          "zero_count": 52,
          "mean_score_0_to_4": 1.2666666666666666,
          "score_percent": 31.666666666666664,
          "score_distribution": {
            "0": 52,
            "1": 48,
            "2": 20,
            "3": 18,
            "4": 12
          }
        }
      },
      "part1": {
        "gpt_6_luna_max": {
          "response_count": 90,
          "correct_count": 11,
          "incorrect_count": 79,
          "partial_credit_count": 35,
          "zero_count": 44,
          "mean_score_0_to_4": 1.0222222222222221,
          "score_percent": 25.555555555555554,
          "score_distribution": {
            "0": 44,
            "1": 25,
            "2": 7,
            "3": 3,
            "4": 11
          }
        },
        "active": {
          "response_count": 90,
          "correct_count": 11,
          "incorrect_count": 79,
          "partial_credit_count": 35,
          "zero_count": 44,
          "mean_score_0_to_4": 1.0222222222222221,
          "score_percent": 25.555555555555554,
          "score_distribution": {
            "0": 44,
            "1": 25,
            "2": 7,
            "3": 3,
            "4": 11
          }
        }
      },
      "part2": {
        "gpt_6_luna_max": {
          "response_count": 60,
          "correct_count": 1,
          "incorrect_count": 59,
          "partial_credit_count": 51,
          "zero_count": 8,
          "mean_score_0_to_4": 1.6333333333333333,
          "score_percent": 40.833333333333336,
          "score_distribution": {
            "0": 8,
            "1": 23,
            "2": 13,
            "3": 15,
            "4": 1
          }
        },
        "active": {
          "response_count": 60,
          "correct_count": 1,
          "incorrect_count": 59,
          "partial_credit_count": 51,
          "zero_count": 8,
          "mean_score_0_to_4": 1.6333333333333333,
          "score_percent": 40.833333333333336,
          "score_distribution": {
            "0": 8,
            "1": 23,
            "2": 13,
            "3": 15,
            "4": 1
          }
        }
      }
    },
    "by_rollout": {
      "1": {
        "response_count": 50,
        "correct_count": 4,
        "incorrect_count": 46,
        "partial_credit_count": 28,
        "zero_count": 18,
        "mean_score_0_to_4": 1.28,
        "score_percent": 32.0,
        "score_distribution": {
          "0": 18,
          "1": 15,
          "2": 6,
          "3": 7,
          "4": 4
        }
      },
      "2": {
        "response_count": 50,
        "correct_count": 2,
        "incorrect_count": 48,
        "partial_credit_count": 31,
        "zero_count": 17,
        "mean_score_0_to_4": 1.22,
        "score_percent": 30.5,
        "score_distribution": {
          "0": 17,
          "1": 16,
          "2": 8,
          "3": 7,
          "4": 2
        }
      },
      "3": {
        "response_count": 50,
        "correct_count": 6,
        "incorrect_count": 44,
        "partial_credit_count": 27,
        "zero_count": 17,
        "mean_score_0_to_4": 1.3,
        "score_percent": 32.5,
        "score_distribution": {
          "0": 17,
          "1": 17,
          "2": 6,
          "3": 4,
          "4": 6
        }
      }
    },
    "tokens": {
      "response_count": 150,
      "usage_record_count": 150,
      "complete_usage_count": 150,
      "missing_usage_count": 0,
      "missing_cached_input_count": 0,
      "complete": true,
      "totals": {
        "cached_input_tokens": 20480,
        "input_tokens": 126957,
        "output_tokens": 68906,
        "total_tokens": 195863
      },
      "known_totals": {
        "cached_input_tokens": 20480,
        "input_tokens": 126957,
        "output_tokens": 68906,
        "total_tokens": 195863
      }
    },
    "by_rollout_part": {
      "part1": {
        "1": {
          "response_count": 30,
          "correct_count": 4,
          "incorrect_count": 26,
          "partial_credit_count": 10,
          "zero_count": 16,
          "mean_score_0_to_4": 1.0333333333333334,
          "score_percent": 25.833333333333336,
          "score_distribution": {
            "0": 16,
            "1": 6,
            "2": 3,
            "3": 1,
            "4": 4
          }
        },
        "2": {
          "response_count": 30,
          "correct_count": 2,
          "incorrect_count": 28,
          "partial_credit_count": 14,
          "zero_count": 14,
          "mean_score_0_to_4": 0.9333333333333333,
          "score_percent": 23.333333333333332,
          "score_distribution": {
            "0": 14,
            "1": 10,
            "2": 2,
            "3": 2,
            "4": 2
          }
        },
        "3": {
          "response_count": 30,
          "correct_count": 5,
          "incorrect_count": 25,
          "partial_credit_count": 11,
          "zero_count": 14,
          "mean_score_0_to_4": 1.1,
          "score_percent": 27.500000000000004,
          "score_distribution": {
            "0": 14,
            "1": 9,
            "2": 2,
            "4": 5
          }
        }
      },
      "part2": {
        "1": {
          "response_count": 20,
          "correct_count": 0,
          "incorrect_count": 20,
          "partial_credit_count": 18,
          "zero_count": 2,
          "mean_score_0_to_4": 1.65,
          "score_percent": 41.25,
          "score_distribution": {
            "0": 2,
            "1": 9,
            "2": 3,
            "3": 6
          }
        },
        "2": {
          "response_count": 20,
          "correct_count": 0,
          "incorrect_count": 20,
          "partial_credit_count": 17,
          "zero_count": 3,
          "mean_score_0_to_4": 1.65,
          "score_percent": 41.25,
          "score_distribution": {
            "0": 3,
            "1": 6,
            "2": 6,
            "3": 5
          }
        },
        "3": {
          "response_count": 20,
          "correct_count": 1,
          "incorrect_count": 19,
          "partial_credit_count": 16,
          "zero_count": 3,
          "mean_score_0_to_4": 1.6,
          "score_percent": 40.0,
          "score_distribution": {
            "0": 3,
            "1": 8,
            "2": 4,
            "3": 4,
            "4": 1
          }
        }
      }
    }
  },
  "answers": [
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "When you double the length and width of a MOSFET, the intrinsic gain remains unchanged. Here's why:\n\nThe intrinsic gain (\\(A_v\\)) of a MOSFET is given by:\n\n\\[\nA_v = g_m \\cdot r_o\n\\]\n\nwhere:\n- \\(g_m\\) is the transconductance,\n- \\(r_o\\) is the output resistance.\n\n1. **Transconductance (\\(g_m\\))**: \\(g_m\\) is proportional to the width-to-length ratio (\\(W/L\\)) of the MOSFET. Doubling both \\(W\\) and \\(L\\) keeps \\(W/L\\) constant, so \\(g_m\\) remains unchanged.\n\n2. **Output resistance (\\(r_o\\))**: \\(r_o\\) is inversely proportional to the channel length (\\(L\\)). Doubling \\(L\\) increases \\(r_o\\), but doubling \\(W\\) increases the current-driving capability, which balances the effect. As a result, \\(r_o\\) also remains unchanged.\n\nSince both \\(g_m\\) and \\(r_o\\) are unaffected by doubling \\(W\\) and \\(L\\), the intrinsic gain (\\(A_v\\)) remains the same.",
        "format": "markdown",
        "sha256": "86c9f1133cf7bb01a7126bb49d02d58c573e733501e17aee69f8c74894f34c70"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly gives intrinsic gain as gm·ro and recognizes that gm is approximately unchanged when W/L is fixed, but it wrongly concludes that ro is unchanged. At constant overdrive, current is approximately unchanged while ro increases with length, so intrinsic gain approximately doubles.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 260,
        "total_tokens": 287,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 260,
        "total_tokens": 287,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "When you double the length and width of a MOSFET, the intrinsic gain remains **unchanged**. Here's why:\n\nThe intrinsic gain (\\(A_v\\)) of a MOSFET is given by:\n\n\\[\nA_v = g_m \\cdot r_o\n\\]\n\nwhere:\n- \\(g_m\\) is the transconductance,\n- \\(r_o\\) is the output resistance.\n\n1. **Transconductance (\\(g_m\\))**: \\(g_m\\) is proportional to the width-to-length ratio (\\(W/L\\)) of the MOSFET. Doubling both \\(W\\) and \\(L\\) keeps \\(W/L\\) constant, so \\(g_m\\) does not change.\n\n2. **Output resistance (\\(r_o\\))**: \\(r_o\\) is inversely proportional to the channel length (\\(L\\)). Doubling \\(L\\) increases \\(r_o\\), but doubling \\(W\\) increases the current-driving capability, which balances the effect. As a result, \\(r_o\\) also remains unchanged.\n\nSince both \\(g_m\\) and \\(r_o\\) are unaffected by doubling \\(W\\) and \\(L\\), the intrinsic gain (\\(A_v = g_m \\cdot r_o\\)) remains the same.",
        "format": "markdown",
        "sha256": "72802a463b716addba59ee0eb0bf1f24c701a84ff3f3f2d0eb48d5411e481432"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that doubling both dimensions keeps W/L and approximately gm unchanged, but incorrectly concludes that ro is unchanged. With the bias condition in the golden solution, ro increases as channel length increases, so intrinsic gain approximately doubles; the answer gives the opposite conclusion.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 272,
        "total_tokens": 299,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 272,
        "total_tokens": 299,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "When you double the length and width of a MOSFET, the intrinsic gain remains **unchanged**. Here's why:\n\nThe intrinsic gain (\\(A_v\\)) of a MOSFET is given by:\n\n\\[\nA_v = g_m \\cdot r_o\n\\]\n\nwhere:\n- \\(g_m\\) is the transconductance,\n- \\(r_o\\) is the output resistance.\n\n1. **Transconductance (\\(g_m\\))**: \\(g_m\\) is proportional to the width-to-length ratio (\\(W/L\\)) of the MOSFET. Doubling both \\(W\\) and \\(L\\) keeps \\(W/L\\) constant, so \\(g_m\\) does not change.\n\n2. **Output resistance (\\(r_o\\))**: \\(r_o\\) is inversely proportional to the drain current (\\(I_D\\)) and depends on the channel length (\\(L\\)). Doubling \\(L\\) increases \\(r_o\\), but doubling \\(W\\) increases \\(I_D\\), which decreases \\(r_o\\). These effects cancel each other out, leaving \\(r_o\\) unchanged.\n\nSince both \\(g_m\\) and \\(r_o\\) remain unchanged, the intrinsic gain (\\(A_v = g_m \\cdot r_o\\)) also remains unchanged when both the length and width of the MOSFET are doubled.",
        "format": "markdown",
        "sha256": "c2cb366792c4982614cf0a832c80d394a427988d3e361cb6d98ca98eba24d4fb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly states that intrinsic gain is gm·ro and that doubling both dimensions leaves W/L, and thus gm under the stated bias assumption, approximately unchanged. But it incorrectly claims the current increase cancels the channel-length effect on ro; with constant overdrive, current stays approximately unchanged, ro roughly doubles, and intrinsic gain increases.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 291,
        "total_tokens": 318,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 291,
        "total_tokens": 318,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine who is correct, let's analyze the relationship between the transconductance (\\(g_m\\)) of a MOSFET and the overdrive voltage (\\(V_{ov}\\)).\n\nThe transconductance of a MOSFET in the saturation region is given by:\n\n\\[\ng_m = \\frac{\\partial I_D}{\\partial V_{GS}} = \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{th}) = 2 \\sqrt{\\mu_n C_{ox} \\frac{W}{L} I_D}\n\\]\n\nHere:\n- \\(I_D\\) is the drain current,\n- \\(V_{GS}\\) is the gate-source voltage,\n- \\(V_{th}\\) is the threshold voltage,\n- \\(V_{ov} = V_{GS} - V_{th}\\) is the overdrive voltage,\n- \\(\\mu_n\\) is the electron mobility,\n- \\(C_{ox}\\) is the oxide capacitance per unit area,\n- \\(W\\) and \\(L\\) are the width and length of the MOSFET channel.\n\nFrom the equation, we see that \\(g_m\\) is directly proportional to \\(V_{ov}\\) (or \\(V_{GS} - V_{th}\\)) in the saturation region. As \\(V_{ov}\\) increases, \\(g_m\\) increases.\n\nThus, **Student A is correct**: the transconductance of a MOSFET increases as the overdrive voltage increases.",
        "format": "markdown",
        "sha256": "12cddf8d60584a815af44284980afa9dace3f86f29e52ad412fda1d13728432f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A and explains that, for fixed device dimensions in saturation, gm = μCox(W/L)Vov, so gm increases with overdrive voltage.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 316,
        "total_tokens": 355,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 316,
        "total_tokens": 355,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine who is correct, let's analyze the relationship between the transconductance (\\(g_m\\)) of a MOSFET and the overdrive voltage (\\(V_{ov} = V_{GS} - V_{th}\\)).\n\nThe transconductance of a MOSFET in the saturation region is given by:\n\n\\[\ng_m = \\frac{\\partial I_D}{\\partial V_{GS}} = \\mu_n C_{ox} \\frac{W}{L} V_{ov}\n\\]\n\nwhere:\n- \\(\\mu_n\\) is the electron mobility,\n- \\(C_{ox}\\) is the oxide capacitance per unit area,\n- \\(W\\) is the width of the MOSFET,\n- \\(L\\) is the length of the MOSFET,\n- \\(V_{ov} = V_{GS} - V_{th}\\) is the overdrive voltage.\n\nFrom this equation, we can see that \\(g_m\\) is directly proportional to \\(V_{ov}\\). This means that as the overdrive voltage increases, the transconductance also increases.\n\n**Conclusion: Student A is correct.** The transconductance of a MOSFET increases as the overdrive voltage increases.",
        "format": "markdown",
        "sha256": "5f4d901dbc767cde2268eb6f8a594df15c673d138c7b4cc67bb7b30e9ed288be"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A and uses the saturation-region relation showing that, for a fixed device size, gm increases with overdrive voltage. Discussing Student B’s fixed-current condition is optional.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 252,
        "total_tokens": 291,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 252,
        "total_tokens": 291,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine who is correct, let's analyze the relationship between the transconductance (\\(g_m\\)) of a MOSFET and the overdrive voltage (\\(V_{ov}\\)).\n\nThe transconductance of a MOSFET in the saturation region is given by:\n\n\\[\ng_m = \\frac{\\partial I_D}{\\partial V_{GS}} = \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{th}) = 2 \\sqrt{\\mu_n C_{ox} \\frac{W}{L} I_D}\n\\]\n\nHere:\n- \\(I_D\\) is the drain current,\n- \\(V_{GS}\\) is the gate-source voltage,\n- \\(V_{th}\\) is the threshold voltage,\n- \\(V_{ov} = V_{GS} - V_{th}\\) is the overdrive voltage,\n- \\(\\mu_n\\) is the electron mobility,\n- \\(C_{ox}\\) is the oxide capacitance per unit area,\n- \\(W\\) and \\(L\\) are the width and length of the MOSFET channel.\n\nFrom the equation, we see that \\(g_m\\) is directly proportional to \\(V_{ov}\\) (or \\(V_{GS} - V_{th}\\)) in the saturation region. As \\(V_{ov}\\) increases, \\(g_m\\) increases.\n\nThus, **Student A is correct**: the transconductance of a MOSFET increases as the overdrive voltage increases.",
        "format": "markdown",
        "sha256": "12cddf8d60584a815af44284980afa9dace3f86f29e52ad412fda1d13728432f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A and explains that, for fixed device dimensions in saturation, gm = μCox(W/L)Vov, so gm increases with overdrive voltage.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 316,
        "total_tokens": 355,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 39,
        "output_tokens": 316,
        "total_tokens": 355,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the small-signal models of PMOS and NMOS devices are not identical, but they are very similar. The key differences arise due to the opposite polarity of the devices:\n\n1. **Polarity of Currents and Voltages**: \n   - In an NMOS transistor, the current flows from the drain to the source, and the gate voltage must be positive relative to the source to turn the device on.\n   - In a PMOS transistor, the current flows from the source to the drain, and the gate voltage must be negative relative to the source to turn the device on.\n\n2. **Small-Signal Parameters**:\n   - The small-signal parameters (e.g., transconductance \\( g_m \\), output resistance \\( r_o \\), and gate capacitances) are defined similarly for both NMOS and PMOS devices, but the signs of the voltages and currents are reversed for PMOS due to the opposite polarity.\n\n3. **Circuit Representation**:\n   - The small-signal equivalent circuit for a PMOS device is essentially the same as that for an NMOS device, except that the direction of the current sources and the polarity of the controlling voltages are reversed.\n\nIn summary, while the small-signal models of PMOS and NMOS devices are structurally similar, the key difference lies in the polarity of the currents and voltages. This difference must be accounted for when analyzing circuits containing both types of transistors.",
        "format": "markdown",
        "sha256": "a0c3283b6d10306c3dac99755cb6453bcdf509fb0e1c9ece6f8bbc56ba9a2d41"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Although it opens with “No,” it explains that the models have essentially the same structure, with current and voltage signs reversed—equivalent to the same form under consistent polarity conventions.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 295,
        "total_tokens": 322,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 295,
        "total_tokens": 322,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the small-signal models of PMOS and NMOS devices are not identical, but they are very similar. The key difference lies in the polarity of the currents and voltages due to the opposite types of charge carriers (holes in PMOS and electrons in NMOS) and the opposite direction of current flow.\n\nHere are the main points of comparison:\n\n1. **Transconductance (\\(g_m\\)):**\n   - Both PMOS and NMOS devices have a transconductance parameter (\\(g_m\\)) that relates the small-signal drain current to the small-signal gate-source voltage (\\(i_d = g_m v_{gs}\\)).\n   - However, for a PMOS, the direction of the current is opposite to that of an NMOS because the PMOS operates with holes as the majority carriers.\n\n2. **Output Resistance (\\(r_o\\)):**\n   - Both devices have an output resistance (\\(r_o\\)) that models the small-signal drain-source resistance due to channel length modulation.\n   - The expressions for \\(r_o\\) are similar, but the signs of the voltages and currents are reversed for PMOS compared to NMOS.\n\n3. **Polarity of Voltages and Currents:**\n   - In an NMOS, the gate-source voltage (\\(V_{GS}\\)) and drain-source voltage (\\(V_{DS}\\)) are positive for normal operation, while in a PMOS, the gate-source voltage (\\(V_{SG}\\)) and source-drain voltage (\\(V_{SD}\\)) are typically negative.\n   - The small-signal parameters are defined with respect to these conventions, so the signs of the small-signal currents and voltages differ.\n\n4. **Circuit Symbols and Biasing:**\n   - The circuit symbols for PMOS and NMOS devices differ, and their biasing conditions are opposite. For example, a PMOS is typically biased with the source at a higher potential than the drain, while an NMOS is biased with the source at a lower potential than the drain.\n\nIn summary, while the small-signal models of PMOS and NMOS devices are structurally similar (both include \\(g_m\\), \\(r_o\\), and capacitances), the signs of the voltages and currents differ due to the opposite nature of the charge carriers and the direction of current flow.",
        "format": "markdown",
        "sha256": "09c165690cd839dd7e80917c79c76363905262887ad36ad96ba70b02615f5035"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It recognizes that the models have the same basic structure and that polarity conventions differ, but incorrectly answers “no” instead of saying they are the same in form when consistent polarities are used.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 482,
        "total_tokens": 509,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 482,
        "total_tokens": 509,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the small-signal models of PMOS and NMOS devices are not identical, but they are very similar. The key differences arise due to the opposite polarity of the devices:\n\n1. **Polarity of Currents and Voltages**: \n   - In an NMOS transistor, the current flows from the drain to the source, and the gate voltage must be positive relative to the source to turn the device on.\n   - In a PMOS transistor, the current flows from the source to the drain, and the gate voltage must be negative relative to the source to turn the device on.\n\n2. **Small-Signal Parameters**:\n   - The small-signal parameters (e.g., transconductance \\( g_m \\), output resistance \\( r_o \\)) are defined similarly for both NMOS and PMOS devices, but the signs of the voltages and currents are reversed for PMOS due to the opposite polarity.\n\n3. **Circuit Representation**:\n   - The small-signal equivalent circuit for a PMOS device is essentially the same as that for an NMOS device, except that the directions of the current sources and the polarity of the controlling voltages are reversed.\n\nIn summary, while the small-signal models of PMOS and NMOS devices are structurally similar, the key difference lies in the polarity of the currents and voltages, which reflects the complementary nature of these two types of transistors.",
        "format": "markdown",
        "sha256": "567ea74059c454ab59e87a9896b81401a763d890696b5e3b03ea40e8efc393ff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "The answer explains that the models are essentially the same in form, with current directions and voltage polarities reversed, matching the golden solution’s full-credit rule.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 287,
        "total_tokens": 314,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 27,
        "output_tokens": 287,
        "total_tokens": 314,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the circuit shown, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The current \\( I_X \\) depends on the operating region of the MOSFET, which is determined by the voltage \\( V_X \\). Here's the step-by-step process:\n\n---\n\n### 1. **MOSFET Operating Regions**\nThe MOSFET \\( M_1 \\) has three operating regions:\n- **Cutoff Region**: \\( V_{GS} < V_{th} \\), where \\( I_X = 0 \\).\n- **Triode Region**: \\( V_{GS} > V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\), where \\( I_X \\) increases linearly with \\( V_X \\).\n- **Saturation Region**: \\( V_{GS} > V_{th} \\) and \\( V_{DS} \\geq V_{GS} - V_{th} \\), where \\( I_X \\) is constant.\n\nHere:\n- \\( V_{GS} = V_X \\) (since the gate is connected to \\( V_X \\)).\n- \\( V_{DS} = V_X \\) (since the drain is connected to \\( V_X \\)).\n\n---\n\n### 2. **Behavior of \\( I_X \\) vs. \\( V_X \\)**\n- For \\( V_X < V_{th} \\): The MOSFET is in the **cutoff region**, and \\( I_X = 0 \\).\n- For \\( V_X > V_{th} \\): The MOSFET enters the **saturation region** because \\( V_{DS} = V_X \\geq V_{GS} - V_{th} \\). In this region, \\( I_X \\) is approximately constant and given by:\n  \\[\n  I_X = \\frac{1}{2} k_n (V_X - V_{th})^2\n  \\]\n  where \\( k_n \\) is the MOSFET's transconductance parameter.\n\n---\n\n### 3. **Sketch**\nThe plot of \\( I_X \\) versus \\( V_X \\) will look like this:\n- **For \\( V_X < V_{th} \\):** \\( I_X = 0 \\) (horizontal line at \\( I_X = 0 \\)).\n- **For \\( V_X > V_{th} \\):** \\( I_X \\) increases quadratically with \\( V_X \\).\n\nThe curve starts at \\( (V_X, I_X) = (V_{th}, 0) \\) and rises quadratically for \\( V_X > V_{th} \\).\n\n---\n\n### Final Sketch\nThe graph will have:\n- A flat region at \\( I_X = 0 \\) for \\( V_X < V_{th} \\).\n- A parabolic rise for \\( V_X > V_{th} \\).",
        "format": "markdown",
        "sha256": "16eed9c0c76544db6d712ba38425b93e673993274ca4409f30e5945f96847a15"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies cutoff below threshold and a quadratic rise above threshold for the diode-connected NMOS. The generic claim that saturation current is constant is imprecise, but the equation and stated sketch give the correct result.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1123,
        "output_tokens": 620,
        "total_tokens": 1743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1123,
        "output_tokens": 620,
        "total_tokens": 1743,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the circuit shown, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The current \\( I_X \\) depends on the operating region of the MOSFET, which is determined by the voltage \\( V_X \\). Here's the step-by-step process:\n\n1. **Identify the MOSFET operating regions:**\n   - **Cutoff region:** When \\( V_{GS} < V_{th} \\), the MOSFET is off, and \\( I_X = 0 \\).\n   - **Triode region:** When \\( V_{GS} > V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\), the MOSFET operates in the linear region, and \\( I_X \\) increases linearly with \\( V_X \\).\n   - **Saturation region:** When \\( V_{GS} > V_{th} \\) and \\( V_{DS} \\geq V_{GS} - V_{th} \\), the MOSFET operates in saturation, and \\( I_X \\) becomes relatively constant.\n\n2. **Determine \\( V_{GS} \\):**\n   - In this circuit, \\( V_{GS} = V_X \\) because the gate is connected to the drain.\n\n3. **Sketch \\( I_X \\) versus \\( V_X \\):**\n   - For \\( V_X < V_{th} \\), \\( I_X = 0 \\) (cutoff region).\n   - For \\( V_X > V_{th} \\), \\( I_X \\) increases with \\( V_X \\) in the triode region and then saturates when \\( V_X \\) reaches \\( V_{GS} - V_{th} \\).\n\n### Final Sketch:\n- The plot starts at \\( I_X = 0 \\) for \\( V_X < V_{th} \\).\n- For \\( V_X > V_{th} \\), \\( I_X \\) increases linearly at first and then flattens out as \\( V_X \\) increases further, indicating the saturation region.",
        "format": "markdown",
        "sha256": "abab38b64f5a4f02ad9630a415a4e0cb2a2e56e97d5ebfc3aa2b8ee1eb526378"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The cutoff behavior below threshold is correct, but the main conclusion above threshold is wrong: a diode-connected NMOS is in saturation and its current rises quadratically, not linearly and then flattening.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1123,
        "output_tokens": 446,
        "total_tokens": 1569,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1123,
        "output_tokens": 446,
        "total_tokens": 1569,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the circuit shown, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The current \\( I_X \\) depends on the operating region of the MOSFET, which is determined by the voltage \\( V_X \\). Here's the step-by-step process:\n\n1. **Identify the MOSFET operating regions:**\n   - **Cutoff region:** When \\( V_{GS} < V_{th} \\), the MOSFET is off, and \\( I_X = 0 \\).\n   - **Triode region:** When \\( V_{GS} > V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\), the MOSFET operates in the linear region, and \\( I_X \\) increases linearly with \\( V_X \\).\n   - **Saturation region:** When \\( V_{GS} > V_{th} \\) and \\( V_{DS} \\geq V_{GS} - V_{th} \\), the MOSFET operates in saturation, and \\( I_X \\) becomes constant.\n\n2. **Relate \\( V_X \\) to \\( V_{GS} \\):**\n   - In this circuit, \\( V_{GS} = V_X \\) because the gate is connected to the source through the voltage source \\( V_X \\).\n\n3. **Sketch \\( I_X \\) versus \\( V_X \\):**\n   - For \\( V_X < V_{th} \\), \\( I_X = 0 \\) (cutoff region).\n   - For \\( V_X > V_{th} \\), \\( I_X \\) increases linearly in the triode region and then saturates at a constant value in the saturation region.\n\nThe resulting plot of \\( I_X \\) versus \\( V_X \\) will look like this:\n- A flat line at \\( I_X = 0 \\) for \\( V_X < V_{th} \\).\n- A rising curve for \\( V_X > V_{th} \\), transitioning from linear to saturation behavior.",
        "format": "markdown",
        "sha256": "ffbc7419f133d54842803753e7289118ace1d17de5bd5c09a74b996969f07a11"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies cutoff below threshold, but misreads the diode-connected NMOS and predicts a linear rise followed by saturation. In this circuit, the device is in saturation as soon as it turns on, so the current rises quadratically.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1123,
        "output_tokens": 442,
        "total_tokens": 1565,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1123,
        "output_tokens": 442,
        "total_tokens": 1565,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the given circuit, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The MOSFET operates in different regions depending on the gate-source voltage \\( V_{GS} \\), which is determined by \\( V_X \\).\n\n### Key Points for Analysis:\n1. **Threshold Voltage (\\( V_{th} \\))**: The MOSFET starts conducting when \\( V_{GS} > V_{th} \\). Below this threshold, \\( I_X = 0 \\).\n2. **Regions of Operation**:\n   - **Cutoff Region**: \\( V_{GS} \\leq V_{th} \\), \\( I_X = 0 \\).\n   - **Saturation Region**: \\( V_{GS} > V_{th} \\) and \\( V_{DS} \\geq V_{GS} - V_{th} \\), \\( I_X \\) is proportional to \\( (V_{GS} - V_{th})^2 \\).\n   - **Triode Region**: \\( V_{GS} > V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\), \\( I_X \\) depends linearly on \\( V_{DS} \\).\n\n3. **Circuit Behavior**:\n   - \\( V_{GS} = V_X \\) (since the source is grounded).\n   - \\( V_{DS} = 1 \\, \\text{V} \\) (fixed by the 1 V source).\n\n### Sketching \\( I_X \\) vs. \\( V_X \\):\n- For \\( V_X \\leq V_{th} \\): \\( I_X = 0 \\) (cutoff region).\n- For \\( V_X > V_{th} \\): The MOSFET enters saturation since \\( V_{DS} = 1 \\, \\text{V} \\geq V_{GS} - V_{th} \\). In this region, \\( I_X \\propto (V_X - V_{th})^2 \\).\n\n### Final Sketch:\n1. The curve starts at \\( I_X = 0 \\) for \\( V_X \\leq V_{th} \\).\n2. For \\( V_X > V_{th} \\), \\( I_X \\) increases quadratically with \\( V_X \\).\n\nThis results in a graph where \\( I_X \\) is zero up to \\( V_{th} \\), and then rises parabolically for \\( V_X > V_{th} \\).",
        "format": "markdown",
        "sha256": "ae3db9e1ff4a05cbe5bef065cdf315f08482c961878657ff0e7790f875a7fae4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies cutoff below threshold and the initial quadratic saturation-region rise, but incorrectly extends saturation to all higher VX. The device enters triode at VX = VTH + 1 V, after which IX rises roughly linearly; missing this key transition makes the sketch incomplete.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 539,
        "total_tokens": 1663,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 539,
        "total_tokens": 1663,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the circuit shown, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The MOSFET operates in different regions depending on the gate-source voltage \\( V_{GS} \\), which is determined by \\( V_X \\).\n\n### Key Points for Analysis:\n1. **Threshold Voltage (\\( V_{th} \\))**: The MOSFET starts conducting when \\( V_{GS} > V_{th} \\). Below \\( V_{th} \\), \\( I_X = 0 \\).\n2. **Regions of Operation**:\n   - **Cutoff Region** (\\( V_{GS} < V_{th} \\)): \\( I_X = 0 \\).\n   - **Saturation Region** (\\( V_{GS} > V_{th} \\) and \\( V_{DS} > V_{GS} - V_{th} \\)): \\( I_X \\propto (V_{GS} - V_{th})^2 \\).\n   - **Linear Region** (\\( V_{GS} > V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\)): \\( I_X \\propto V_{DS} \\).\n\n3. **Circuit Behavior**:\n   - \\( V_{GS} = V_X \\) (since the source is grounded).\n   - \\( V_{DS} = 1 \\, \\text{V} \\) (fixed by the 1 V source).\n\n### Sketching \\( I_X \\) vs. \\( V_X \\):\n- For \\( V_X < V_{th} \\): \\( I_X = 0 \\) (cutoff region).\n- For \\( V_X > V_{th} \\): The MOSFET enters saturation since \\( V_{DS} = 1 \\, \\text{V} > V_{GS} - V_{th} \\). In this region, \\( I_X \\propto (V_X - V_{th})^2 \\).\n\n### Final Sketch:\n1. Start with \\( I_X = 0 \\) for \\( V_X < V_{th} \\).\n2. For \\( V_X > V_{th} \\), plot a parabolic curve representing \\( I_X \\propto (V_X - V_{th})^2 \\).\n\nThis results in a curve that is flat for \\( V_X < V_{th} \\) and rises quadratically for \\( V_X > V_{th} \\).",
        "format": "markdown",
        "sha256": "cfd9830d92ed7cefd44bf60b1d3a9e731a12e67df73c5025040e17b5e0dd188e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies cutoff and the initial quadratic rise, but incorrectly claims the MOSFET remains in saturation for all VX > VTH. Above VTH + 1 V it enters triode and IX rises roughly linearly, so the key part of the sketch is missing.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 528,
        "total_tokens": 1652,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 528,
        "total_tokens": 1652,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch \\( I_X \\) versus \\( V_X \\) for the given circuit, we need to analyze the behavior of the MOSFET \\( M_1 \\) in the circuit. The MOSFET operates in different regions depending on the gate-source voltage \\( V_{GS} \\) and the drain-source voltage \\( V_{DS} \\). Here's the step-by-step process:\n\n---\n\n### 1. **Circuit Analysis**\n- \\( V_{GS} = V_X \\) (since the source is grounded).\n- \\( V_{DS} = 1 \\, \\text{V} \\) (fixed by the 1 V voltage source).\n\nThe current \\( I_X \\) through the MOSFET depends on its operating region:\n\n#### **a. Cutoff Region (\\( V_{GS} < V_{th} \\)):**\n- If \\( V_X < V_{th} \\), the MOSFET is off, and \\( I_X = 0 \\).\n\n#### **b. Saturation Region (\\( V_{GS} \\geq V_{th} \\) and \\( V_{DS} \\geq V_{GS} - V_{th} \\)):**\n- If \\( V_X \\geq V_{th} \\), the MOSFET operates in saturation.\n- The drain current \\( I_X \\) is given by:\n  \\[\n  I_X = \\frac{1}{2} k_n (V_{GS} - V_{th})^2 = \\frac{1}{2} k_n (V_X - V_{th})^2\n  \\]\n  where \\( k_n = \\mu_n C_{ox} \\frac{W}{L} \\) is the process-dependent transconductance parameter.\n\n#### **c. Triode Region (\\( V_{GS} \\geq V_{th} \\) and \\( V_{DS} < V_{GS} - V_{th} \\)):**\n- In this circuit, \\( V_{DS} = 1 \\, \\text{V} \\) is fixed. If \\( V_X \\) is large enough such that \\( V_{DS} < V_{GS} - V_{th} \\), the MOSFET enters the triode region.\n- The current \\( I_X \\) in this region is:\n  \\[\n  I_X = k_n \\left[ (V_X - V_{th}) V_{DS} - \\frac{V_{DS}^2}{2} \\right]\n  \\]\n\n---\n\n### 2. **Sketching \\( I_X \\) vs. \\( V_X \\):**\n- For \\( V_X < V_{th} \\): \\( I_X = 0 \\) (cutoff region).\n- For \\( V_X \\geq V_{th} \\): \\( I_X \\) increases quadratically in the saturation region.\n- If \\( V_X \\) becomes large enough such that \\( V_{DS} < V_{GS} - V_{th} \\), the MOSFET transitions to the triode region, and \\( I_X \\) increases linearly with \\( V_X \\).\n\n---\n\n### 3. **Qualitative Plot:**\n- The plot starts at \\( I_X = 0 \\) for \\( V_X < V_{th} \\).\n- For \\( V_X \\geq V_{th} \\), \\( I_X \\) increases quadratically in the saturation region.\n- If \\( V_X \\) becomes very large, \\( I_X \\) transitions to a linear increase in the triode region.",
        "format": "markdown",
        "sha256": "ec6b727fab32b0458435327f6a1846c7bb538bc488337e3902a59186a1b0cd30"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies cutoff, the quadratic saturation rise, and the transition to a roughly linear triode-region rise when the fixed 1 V drain voltage is exceeded by the overdrive. The stated region condition implies the transition at V_X = V_th + 1 V.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 739,
        "total_tokens": 1863,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 739,
        "total_tokens": 1863,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the device shown in the figure can act as a current source. The circuit consists of a MOSFET (M1) with its gate and drain connected together, forming a diode-connected MOSFET. In this configuration, the MOSFET operates in the saturation region, where the current \\( I_x \\) is primarily determined by the gate-source voltage \\( V_{GS} \\) and the MOSFET's parameters (e.g., \\( k_n \\), \\( V_{th} \\)).\n\nThis setup is commonly used in analog circuits to create a current source or a current mirror, as the current \\( I_x \\) remains relatively constant for a wide range of output voltages, provided the MOSFET stays in saturation.",
        "format": "markdown",
        "sha256": "d7fe86221bb917d4d6eb72bb8627684d1853ae4709f0abe790c592a2ec6ffd19"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly says the device can act as a current source. As drawn, M1 is a diode-connected PMOS with low small-signal impedance (about 1/gm), so its current varies with terminal voltage rather than remaining nearly constant.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 151,
        "total_tokens": 596,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 151,
        "total_tokens": 596,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the device shown in the figure can act as a current source. The circuit consists of a MOSFET (M1) with its gate and drain connected together, forming a diode-connected MOSFET. In this configuration, the MOSFET operates in the saturation region, where the current \\( I_x \\) is primarily determined by the MOSFET's characteristics and the applied voltage.\n\nThis configuration is often used in analog circuits to create a constant current source, as the current through the MOSFET remains relatively constant for a wide range of output voltages, provided the MOSFET remains in saturation.",
        "format": "markdown",
        "sha256": "2920e17795d06f6d95ec4ec997d1eff60f77fdab1218dae7f83b5b0853ca2405"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly concludes that the diode-connected device can act as a current source. As drawn, M1 is a PMOS with gate and drain grounded; it presents low impedance (about 1/gm), so its current varies with terminal voltage.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 124,
        "total_tokens": 569,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 124,
        "total_tokens": 569,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the device shown in the figure can act as a current source. The circuit consists of a MOSFET (M1) with its gate and drain connected together, forming a diode-connected MOSFET. In this configuration, the MOSFET operates in the saturation region, where the current \\( I_x \\) is primarily determined by the MOSFET's characteristics and the applied voltage.\n\nThis setup is commonly used in analog circuits to create a current source or a current mirror, as the current through the MOSFET remains relatively constant for a wide range of output voltages, provided the MOSFET stays in saturation.",
        "format": "markdown",
        "sha256": "58c2561e2e1a5c9f55b90d24a71cf079f3b14f13a2eccfa3c7e4301223507734"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly concludes that the diode-connected device can act as a current source. As drawn, M1 is a PMOS whose diode connection presents a low impedance (about 1/gm), not a nearly constant-current output.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 127,
        "total_tokens": 572,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 445,
        "output_tokens": 127,
        "total_tokens": 572,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (denoted as \\( M_1 \\)) with a resistive load (\\( R_D \\)) and a source resistor (\\( R_S \\)). Here's the analysis:\n\n---\n\n### **1. Circuit Description**\n- **Input (\\( V_{in} \\))**: Applied to the gate of the MOSFET.\n- **Output (\\( V_{out} \\))**: Taken from the drain of the MOSFET.\n- **\\( R_S \\)**: Source resistor, which provides negative feedback and stabilizes the circuit.\n- **\\( R_D \\)**: Drain resistor, which determines the output voltage swing.\n- **\\( V_{DD} \\)**: Supply voltage.\n\n---\n\n### **2. Operating Principle**\n- The MOSFET operates in the **saturation region** for amplification.\n- The input signal \\( V_{in} \\) modulates the gate-source voltage (\\( V_{GS} \\)), which controls the drain current (\\( I_D \\)).\n- The drain current flows through \\( R_D \\), creating a voltage drop that determines the output voltage \\( V_{out} \\).\n\n---\n\n### **3. Key Equations**\n#### **DC Analysis**\n1. **Gate Voltage (\\( V_G \\))**:\n   \\[\n   V_G = V_{in}\n   \\]\n\n2. **Source Voltage (\\( V_S \\))**:\n   \\[\n   V_S = I_D R_S\n   \\]\n\n3. **Gate-Source Voltage (\\( V_{GS} \\))**:\n   \\[\n   V_{GS} = V_G - V_S\n   \\]\n\n4. **Drain Voltage (\\( V_D \\))**:\n   \\[\n   V_D = V_{DD} - I_D R_D\n   \\]\n\n5. **Output Voltage (\\( V_{out} \\))**:\n   \\[\n   V_{out} = V_D\n   \\]\n\n#### **AC Analysis**\n- The small-signal voltage gain (\\( A_v \\)) is given by:\n   \\[\n   A_v = -\\frac{g_m R_D}{1 + g_m R_S}\n   \\]\n   where:\n   - \\( g_m \\): Transconductance of the MOSFET (\\( g_m = \\frac{2I_D}{V_{GS} - V_{th}} \\)).\n   - \\( V_{th} \\): Threshold voltage of the MOSFET.\n\n---\n\n### **4. Observations**\n- **Voltage Gain**: The gain is negative, indicating an inverted output.\n- **Role of \\( R_S \\)**: Provides negative feedback, reducing gain but improving linearity and stability.\n- **Output Swing**: Limited by \\( V_{DD} \\) and the voltage drops across \\( R_D \\) and \\( R_S \\).\n\n---\n\n### **5. Applications**\n- This circuit is commonly used in analog signal amplification, such as in audio amplifiers or sensor signal processing.",
        "format": "markdown",
        "sha256": "2b7458a1e7dbe94f424d3cf282b352010a9393b26ae42d908f0cd18302c100d2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It gives the correct inverting source-degenerated common-source gain, but never identifies M1 as a PMOS and its DC equations place the resistors as in an NMOS stage, opposite to the figure. That is a significant topology and device-role error.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1120,
        "output_tokens": 622,
        "total_tokens": 1742,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1120,
        "output_tokens": 622,
        "total_tokens": 1742,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (denoted as \\( M_1 \\)) with a resistive load (\\( R_D \\)) and a source resistor (\\( R_S \\)). Below is the analysis of the circuit:\n\n---\n\n### **1. Circuit Description**\n- **Input (\\( V_{in} \\))**: The input signal is applied to the gate of the MOSFET.\n- **Output (\\( V_{out} \\))**: The output is taken from the drain of the MOSFET.\n- **\\( R_S \\)**: The source resistor provides negative feedback, stabilizing the circuit.\n- **\\( R_D \\)**: The drain resistor converts the drain current into a voltage signal.\n- **\\( V_{DD} \\)**: The supply voltage powers the circuit.\n\n---\n\n### **2. Operating Principle**\n- The MOSFET operates in the **saturation region** for amplification. This requires:\n  \\[\n  V_{DS} > V_{GS} - V_{th}\n  \\]\n  where \\( V_{DS} \\) is the drain-source voltage, \\( V_{GS} \\) is the gate-source voltage, and \\( V_{th} \\) is the threshold voltage of the MOSFET.\n\n- The small-signal input voltage (\\( v_{in} \\)) modulates the gate-source voltage (\\( V_{GS} \\)), which in turn controls the drain current (\\( I_D \\)).\n\n---\n\n### **3. DC Analysis**\n- The DC operating point (bias point) is determined by the resistors \\( R_S \\) and \\( R_D \\), and the supply voltage \\( V_{DD} \\).\n- The gate current is negligible for a MOSFET, so the gate voltage is:\n  \\[\n  V_G = V_{in}\n  \\]\n- The source voltage is:\n  \\[\n  V_S = I_D R_S\n  \\]\n- The drain voltage is:\n  \\[\n  V_D = V_{DD} - I_D R_D\n  \\]\n- The gate-source voltage is:\n  \\[\n  V_{GS} = V_G - V_S\n  \\]\n\nUsing these equations, \\( I_D \\) can be solved iteratively or using the MOSFET's current equation in the saturation region:\n\\[\nI_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n\\]\nwhere \\( k_n \\) is the MOSFET's transconductance parameter.\n\n---\n\n### **4. AC Analysis**\n- For small-signal analysis, the MOSFET is modeled as a voltage-controlled current source with transconductance \\( g_m \\):\n  \\[\n  g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th})\n  \\]\n- The small-signal voltage gain is:\n  \\[\n  A_v = \\frac{v_{out}}{v_{in}} = -\\frac{g_m R_D}{1 + g_m R_S}\n  \\]\n  - The negative sign indicates a 180° phase shift between input and output.\n  - \\( R_S \\) introduces feedback, reducing the gain but improving linearity and stability.\n\n---\n\n### **5. Key Observations**\n- **Voltage Gain**: The gain depends on \\( g_m \\), \\( R_D \\), and \\( R_S \\). Increasing \\( R_D \\) or \\( g_m \\) increases the gain, while \\( R_S \\) reduces it.\n- **Input Impedance**: The input impedance is high because the gate current is negligible.\n- **Output Impedance**: The output impedance is approximately \\( R_D \\) in parallel with the MOSFET's output resistance.\n\n---\n\n### **6. Applications**\nThis circuit is commonly used in:\n- Analog signal amplification.\n- Audio amplifiers.\n- RF amplifiers.",
        "format": "markdown",
        "sha256": "52504910a27725d6dde2cf01b8379cf561e6d537a4276ac87893058529ba6d26"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The common-source topology and inverting gain are correct, but the bias and saturation equations implicitly treat M1 as an NMOS with the opposite supply-resistor arrangement. The actual circuit uses a PMOS, so the device-polarity error merits 1.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1120,
        "output_tokens": 824,
        "total_tokens": 1944,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1120,
        "output_tokens": 824,
        "total_tokens": 1944,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (M₁). Here's the analysis:\n\n---\n\n### **1. Circuit Description**\n- **M₁**: The MOSFET is the active device, operating in the saturation region for amplification.\n- **\\( R_S \\)**: The source resistor provides feedback and stabilizes the operating point.\n- **\\( R_D \\)**: The drain resistor converts the drain current into an output voltage.\n- **\\( V_{DD} \\)**: The supply voltage powers the circuit.\n- **\\( V_{in} \\)**: The input signal is applied to the gate of the MOSFET.\n- **\\( V_{out} \\)**: The output voltage is taken from the drain of the MOSFET.\n\n---\n\n### **2. Operating Regions**\nFor the MOSFET to operate in the saturation region (required for amplification):\n\\[\nV_{GS} > V_{th} \\quad \\text{and} \\quad V_{DS} > V_{GS} - V_{th}\n\\]\nwhere:\n- \\( V_{GS} \\): Gate-to-source voltage.\n- \\( V_{DS} \\): Drain-to-source voltage.\n- \\( V_{th} \\): Threshold voltage of the MOSFET.\n\n---\n\n### **3. DC Analysis**\nThe DC operating point (biasing) is determined by:\n- \\( V_{GS} \\): Set by the input \\( V_{in} \\).\n- \\( I_D \\): The drain current, which flows through \\( R_D \\) and \\( R_S \\).\n\nUsing Kirchhoff's Voltage Law (KVL) for the source loop:\n\\[\nV_{GS} = V_{in} - I_D R_S\n\\]\n\nFor the drain loop:\n\\[\nV_{out} = V_{DD} - I_D R_D\n\\]\n\n---\n\n### **4. Small-Signal Analysis**\nFor small-signal operation, the MOSFET is modeled using its small-signal parameters:\n- **Transconductance (\\( g_m \\))**: Relates the small-signal drain current to the gate-source voltage:\n  \\[\n  g_m = \\frac{2 I_D}{V_{GS} - V_{th}}\n  \\]\n- **Output Resistance (\\( r_o \\))**: Represents the MOSFET's channel-length modulation effect.\n\nThe small-signal voltage gain is:\n\\[\nA_v = \\frac{v_{out}}{v_{in}} = -g_m R_D \\parallel r_o\n\\]\nwhere \\( R_D \\parallel r_o \\) is the parallel combination of \\( R_D \\) and \\( r_o \\).\n\n---\n\n### **5. Key Observations**\n- The circuit inverts the input signal (\\( A_v < 0 \\)).\n- The gain depends on \\( g_m \\), \\( R_D \\), and \\( r_o \\).\n- \\( R_S \\) provides negative feedback, improving stability but reducing gain.\n\n---\n\n### **6. Applications**\nThis circuit is commonly used in:\n- Analog signal amplification.\n- Audio amplifiers.\n- Intermediate stages in RF circuits.",
        "format": "markdown",
        "sha256": "233b42de5b08103df402beb1aa4b6b32abc2f0cbb1eb7f9a8ecf826434ef4e8b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly recognizes a common-source stage, inversion, and that source degeneration reduces gain. However, it omits the PMOS identity and the essential degeneration factor in the gain, and its DC equations assume supply/resistor connections inconsistent with the shown circuit.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1120,
        "output_tokens": 648,
        "total_tokens": 1768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1120,
        "output_tokens": 648,
        "total_tokens": 1768,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** with a source resistor (\\(R_S\\)). Here's the analysis:\n\n---\n\n### **Circuit Description**\n1. **Transistor \\(M_1\\):** This is an n-channel MOSFET operating as the active device.\n2. **\\(V_{DD}\\):** The supply voltage.\n3. **\\(R_S\\):** The source resistor, which provides negative feedback and stabilizes the circuit.\n4. **\\(V_{in}\\):** The input voltage applied to the gate of the MOSFET.\n5. **\\(V_{out}\\):** The output voltage taken from the drain of the MOSFET.\n\n---\n\n### **Operation**\n1. **Input Stage:**\n   - The input voltage (\\(V_{in}\\)) controls the gate-source voltage (\\(V_{GS}\\)) of the MOSFET.\n   - The MOSFET operates in the saturation region if \\(V_{GS} > V_{th}\\) (threshold voltage) and \\(V_{DS} > V_{GS} - V_{th}\\).\n\n2. **Output Stage:**\n   - The output voltage (\\(V_{out}\\)) is taken at the drain of the MOSFET.\n   - The drain current (\\(I_D\\)) flows through the source resistor (\\(R_S\\)) and is related to the MOSFET's operating point.\n\n---\n\n### **Key Equations**\n1. **Drain Current (\\(I_D\\)):**\n   In the saturation region:\n   \\[\n   I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n   \\]\n   where \\(k_n = \\mu_n C_{ox} \\frac{W}{L}\\) is the MOSFET's transconductance parameter.\n\n2. **Source Voltage (\\(V_S\\)):**\n   \\[\n   V_S = I_D R_S\n   \\]\n\n3. **Gate-Source Voltage (\\(V_{GS}\\)):**\n   \\[\n   V_{GS} = V_{in} - V_S\n   \\]\n\n4. **Output Voltage (\\(V_{out}\\)):**\n   \\[\n   V_{out} = V_{DD} - I_D R_D\n   \\]\n   where \\(R_D\\) is the drain resistance (if present). In this circuit, \\(R_D = 0\\), so:\n   \\[\n   V_{out} = V_{DD} - I_D R_S\n   \\]\n\n---\n\n### **Small-Signal Analysis**\nFor small variations in \\(V_{in}\\), the circuit amplifies the input signal. The small-signal gain (\\(A_v\\)) is given by:\n\\[\nA_v = -g_m \\cdot R_{eff}\n\\]\nwhere:\n- \\(g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th})\\) is the transconductance.\n- \\(R_{eff} = R_S || r_o\\), where \\(r_o\\) is the MOSFET's output resistance.\n\n---\n\n### **Key Observations**\n1. **Negative Feedback:** The source resistor (\\(R_S\\)) introduces negative feedback, which stabilizes the operating point and reduces gain.\n2. **Voltage Gain:** The gain is inversely proportional to \\(R_S\\), as \\(R_S\\) reduces the effective transconductance.\n3. **Output Swing:** The output voltage swing is limited by \\(V_{DD}\\) and the voltage drop across \\(R_S\\).\n\n---\n\nThis circuit is commonly used in analog electronics for amplification with improved stability due to the source resistor.",
        "format": "markdown",
        "sha256": "f3dee2ba8394426b45b1839f244c19be9af28a77681bd10dc423423c2037140e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the source follower as a common-source amplifier, places the output at the drain, and gives an unrelated gain expression. It misses the circuit’s essential positive, less-than-unity gain.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 769,
        "total_tokens": 1549,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 769,
        "total_tokens": 1549,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** with a source resistor (\\(R_S\\)). Here's the analysis:\n\n---\n\n### **Circuit Description**\n1. **Transistor \\(M_1\\):**\n   - \\(M_1\\) is an n-channel MOSFET.\n   - The gate is connected to the input voltage (\\(V_{in}\\)).\n   - The drain is connected to the supply voltage (\\(V_{DD}\\)) through the MOSFET's channel.\n   - The source is connected to ground through the resistor \\(R_S\\).\n\n2. **Input and Output:**\n   - \\(V_{in}\\) is the input signal applied to the gate of \\(M_1\\).\n   - \\(V_{out}\\) is the output voltage, measured at the source of \\(M_1\\).\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The MOSFET operates in the saturation region if the gate-source voltage (\\(V_{GS}\\)) is greater than the threshold voltage (\\(V_{th}\\)) and the drain-source voltage (\\(V_{DS}\\)) is sufficiently large.\n   - The source resistor \\(R_S\\) provides negative feedback, stabilizing the operating point.\n\n2. **Small-Signal Analysis:**\n   - The small-signal gain of the circuit is determined by the transconductance of the MOSFET (\\(g_m\\)) and the source resistor (\\(R_S\\)).\n   - The gain is approximately:\n     \\[\n     A_v = \\frac{V_{out}}{V_{in}} = \\frac{-g_m R_S}{1 + g_m R_S}\n     \\]\n     The negative sign indicates a phase inversion between the input and output.\n\n3. **Output Voltage:**\n   - The output voltage is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_S\n     \\]\n     where \\(I_D\\) is the drain current.\n\n---\n\n### **Key Features**\n1. **Voltage Gain:**\n   - The gain is less than 1 due to the feedback provided by \\(R_S\\).\n   - This makes the circuit suitable for applications requiring low gain and high linearity.\n\n2. **Input Impedance:**\n   - The input impedance is high because the gate of the MOSFET draws negligible current.\n\n3. **Output Impedance:**\n   - The output impedance is determined by \\(R_S\\) and the small-signal parameters of the MOSFET.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing, such as amplifying small signals in audio or sensor applications.",
        "format": "markdown",
        "sha256": "bbd19b130be9e206efc46435294cc2e65dfebcbe4ea3a98681c797b7c835908f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The output is at the source, so this is a source follower, not a common-source amplifier. Its gain is positive, approximately gmRS/(1 + gmRS); the candidate incorrectly gives it a negative, inverting gain. It identifies some relevant connections and gain magnitude, but misses the essential topology and phase.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 548,
        "total_tokens": 1328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 548,
        "total_tokens": 1328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** with a source resistor (\\(R_S\\)). Here's the analysis:\n\n---\n\n### **1. Circuit Description**\n- **Transistor \\(M_1\\):** This is an n-channel MOSFET operating as the active device.\n- **\\(V_{DD}\\):** The supply voltage.\n- **\\(R_S\\):** The source resistor, which provides negative feedback and stabilizes the circuit.\n- **\\(V_{in}\\):** The input voltage applied to the gate of the MOSFET.\n- **\\(V_{out}\\):** The output voltage taken from the drain of the MOSFET.\n\n---\n\n### **2. Operating Regions**\nThe MOSFET operates in one of three regions:\n1. **Cutoff Region:** When \\(V_{GS} < V_{th}\\), the MOSFET is off, and no current flows.\n2. **Triode Region:** When \\(V_{GS} > V_{th}\\) and \\(V_{DS} < V_{GS} - V_{th}\\), the MOSFET operates as a resistor.\n3. **Saturation Region:** When \\(V_{GS} > V_{th}\\) and \\(V_{DS} \\geq V_{GS} - V_{th}\\), the MOSFET operates as an amplifier.\n\nFor amplification, the MOSFET must operate in the **saturation region**.\n\n---\n\n### **3. DC Analysis**\nTo determine the operating point:\n1. **Gate Voltage (\\(V_G\\)):** \\(V_G = V_{in}\\).\n2. **Source Voltage (\\(V_S\\)):** \\(V_S = I_D R_S\\), where \\(I_D\\) is the drain current.\n3. **Gate-Source Voltage (\\(V_{GS}\\)):** \\(V_{GS} = V_G - V_S = V_{in} - I_D R_S\\).\n4. **Drain Voltage (\\(V_D\\)):** \\(V_D = V_{DD} - I_D R_D\\), where \\(R_D\\) is the drain resistance (not shown in this circuit).\n\nThe drain current \\(I_D\\) is determined by the MOSFET's current equation in saturation:\n\\[\nI_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2,\n\\]\nwhere \\(k_n = \\mu_n C_{ox} \\frac{W}{L}\\) is the MOSFET's transconductance parameter.\n\n---\n\n### **4. AC Analysis**\nFor small-signal analysis:\n1. **Small-Signal Model:** Replace the MOSFET with its small-signal equivalent (a voltage-controlled current source with transconductance \\(g_m\\)).\n2. **Transconductance (\\(g_m\\)):**\n   \\[\n   g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th}).\n   \\]\n3. **Voltage Gain (\\(A_v\\)):**\n   The voltage gain is given by:\n   \\[\n   A_v = -\\frac{g_m R_D}{1 + g_m R_S},\n   \\]\n   where \\(R_D\\) is the drain resistance. In this circuit, \\(R_D\\) is not explicitly shown, so the output impedance of the MOSFET may dominate.\n\n---\n\n### **5. Source Degeneration Effect**\nThe source resistor \\(R_S\\) introduces **negative feedback**, which:\n- Reduces the gain (\\(A_v\\)).\n- Improves linearity.\n- Stabilizes the operating point against variations in \\(V_{th}\\) or \\(k_n\\).\n\n---\n\n### **6. Output Voltage (\\(V_{out}\\)):**\nThe output voltage is:\n\\[\nV_{out} = V_D = V_{DD} - I_D R_D.\n\\]\n\n---\n\n### **Summary**\n- The circuit is a common-source amplifier with source degeneration.\n- The gain is reduced due to \\(R_S\\), but stability and linearity are improved.\n- Proper biasing ensures the MOSFET operates in the saturation region for amplification.",
        "format": "markdown",
        "sha256": "8739c2bf9755eab577fcb4d55f67d67dd122d41d25380d5d83f08b437fdcf0ee"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source follower as a common-source stage and places the output at the drain. Its gain expression and drain-resistor analysis therefore do not describe the circuit; only generic MOSFET and source-resistor observations are relevant.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 866,
        "total_tokens": 1646,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 866,
        "total_tokens": 1646,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using an NMOS transistor \\( M_1 \\). Here's the analysis:\n\n---\n\n### Components:\n1. **\\( M_1 \\)**: NMOS transistor, acts as the active device.\n2. **\\( R_D \\)**: Drain resistor, converts the drain current into a voltage signal.\n3. **\\( V_{DD} \\)**: Supply voltage.\n4. **\\( V_{in} \\)**: Input voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: Output voltage taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **Input Stage**:\n   - The input voltage \\( V_{in} \\) is applied to the gate of \\( M_1 \\).\n   - The gate-source voltage \\( V_{GS} \\) controls the current \\( I_D \\) through the transistor.\n\n2. **Output Stage**:\n   - The drain current \\( I_D \\) flows through \\( R_D \\), creating a voltage drop across \\( R_D \\).\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n\n3. **Modes of Operation**:\n   - \\( M_1 \\) operates in the **saturation region** for amplification, where:\n     \\[\n     I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n     \\]\n     Here, \\( k_n = \\mu_n C_{ox} \\frac{W}{L} \\) is the process transconductance parameter, \\( V_{th} \\) is the threshold voltage, and \\( W/L \\) is the transistor's width-to-length ratio.\n\n4. **Small-Signal Gain**:\n   - The small-signal voltage gain \\( A_v \\) is:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of \\( M_1 \\), given by:\n     \\[\n     g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th})\n     \\]\n\n---\n\n### Key Observations:\n1. **Inversion**:\n   - The circuit inverts the input signal, as indicated by the negative gain \\( A_v \\).\n\n2. **Biasing**:\n   - Proper biasing of \\( V_{GS} \\) is required to ensure \\( M_1 \\) operates in the saturation region.\n\n3. **Output Swing**:\n   - The output voltage \\( V_{out} \\) is limited by \\( V_{DD} \\) (upper limit) and the voltage drop across \\( R_D \\) (lower limit).\n\n4. **Frequency Response**:\n   - The circuit's frequency response is determined by parasitic capacitances in \\( M_1 \\) and the load.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing as a voltage amplifier.",
        "format": "markdown",
        "sha256": "5b7e828891fe647be4dc6020d8a64dfb1849edb516f6e19d24098e0e0f6ac435"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the topology and input connection: the circuit is common-gate, with Vin at the source and the gate AC-grounded. Its gain is non-inverting (approximately +gm(RD || ro)), not the stated inverting common-source gain.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 648,
        "total_tokens": 1428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 648,
        "total_tokens": 1428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using an NMOS transistor \\( M_1 \\). Here's the analysis:\n\n---\n\n### Components:\n1. **\\( M_1 \\)**: NMOS transistor, acting as the active device.\n2. **\\( R_D \\)**: Drain resistor, which converts the drain current into a voltage.\n3. **\\( V_{DD} \\)**: Supply voltage.\n4. **\\( V_{in} \\)**: Input voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: Output voltage taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **Input Stage**:\n   - The input voltage \\( V_{in} \\) is applied to the gate of \\( M_1 \\).\n   - The gate-source voltage \\( V_{GS} \\) controls the current \\( I_D \\) through the transistor.\n\n2. **Output Stage**:\n   - The drain current \\( I_D \\) flows through \\( R_D \\), creating a voltage drop across \\( R_D \\).\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n\n3. **Modes of Operation**:\n   - \\( M_1 \\) operates in the **saturation region** for amplification, where:\n     \\[\n     I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n     \\]\n     Here, \\( k_n \\) is the process transconductance parameter, and \\( V_{th} \\) is the threshold voltage of the NMOS transistor.\n\n4. **Small-Signal Analysis**:\n   - For small variations in \\( V_{in} \\), the small-signal output voltage \\( v_{out} \\) is related to the small-signal input voltage \\( v_{in} \\) by the gain \\( A_v \\):\n     \\[\n     A_v = \\frac{v_{out}}{v_{in}} = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of \\( M_1 \\), given by:\n     \\[\n     g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th})\n     \\]\n\n---\n\n### Key Observations:\n1. **Voltage Gain**:\n   - The circuit provides a negative voltage gain, meaning the output is inverted relative to the input.\n   - The magnitude of the gain depends on \\( g_m \\) and \\( R_D \\).\n\n2. **Input and Output Impedance**:\n   - The input impedance is high because the gate of the NMOS transistor draws negligible current.\n   - The output impedance is approximately \\( R_D \\).\n\n3. **Biasing**:\n   - Proper biasing of \\( V_{GS} \\) is required to ensure \\( M_1 \\) operates in the saturation region.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal amplification, such as in audio amplifiers or as a building block in operational amplifiers.",
        "format": "markdown",
        "sha256": "d6aeae52dd6ca9a9a54980358c4a35c182575a085e095437f94c065544084858"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source-driven, gate-ac-grounded common-gate stage as a gate-driven common-source stage. Consequently, its input impedance and gain sign are wrong; the actual gain is non-inverting and the input resistance is approximately 1/gm.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 665,
        "total_tokens": 1445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 665,
        "total_tokens": 1445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using an NMOS transistor \\( M_1 \\). Here's the analysis:\n\n---\n\n### Components:\n1. **\\( M_1 \\)**: NMOS transistor, acts as the active device.\n2. **\\( R_D \\)**: Drain resistor, converts the current through \\( M_1 \\) into a voltage.\n3. **\\( V_{DD} \\)**: Supply voltage, provides power to the circuit.\n4. **\\( V_{in} \\)**: Input voltage, applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: Output voltage, taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **Input Stage**:\n   - The input voltage \\( V_{in} \\) is applied to the gate of \\( M_1 \\).\n   - The gate-source voltage \\( V_{GS} \\) controls the current \\( I_D \\) through the transistor.\n\n2. **Output Stage**:\n   - The current \\( I_D \\) flows through the drain resistor \\( R_D \\), creating a voltage drop across \\( R_D \\).\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n\n3. **Modes of Operation**:\n   - \\( M_1 \\) operates in the **saturation region** for amplification, where:\n     \\[\n     I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n     \\]\n     Here, \\( k_n \\) is the process transconductance parameter, and \\( V_{th} \\) is the threshold voltage of the NMOS transistor.\n\n4. **Small-Signal Analysis**:\n   - For small variations in \\( V_{in} \\), the small-signal gain \\( A_v \\) is:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of \\( M_1 \\), given by:\n     \\[\n     g_m = \\frac{\\partial I_D}{\\partial V_{GS}} = k_n (V_{GS} - V_{th})\n     \\]\n\n---\n\n### Key Observations:\n1. **Voltage Gain**:\n   - The circuit inverts the input signal (\\( A_v < 0 \\)).\n   - The magnitude of the gain depends on \\( g_m \\) and \\( R_D \\).\n\n2. **Output Voltage Swing**:\n   - The output voltage \\( V_{out} \\) is limited by \\( V_{DD} \\) and the voltage drop across \\( R_D \\).\n   - To avoid distortion, \\( V_{out} \\) must stay within the linear region of operation.\n\n3. **Biasing**:\n   - Proper biasing of \\( V_{GS} \\) is crucial to ensure \\( M_1 \\) operates in the saturation region.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing as a voltage amplifier.",
        "format": "markdown",
        "sha256": "37ab190f83bb0ae909ed7a26885b8d96af005867d01585f47e5336a9ba23faff"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the input as applied to the gate rather than the source, so it analyzes the wrong topology and gives the wrong gain sign. The circuit is common-gate, with approximately +gm(RD || ro) gain and input resistance near 1/gm.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 649,
        "total_tokens": 1429,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 649,
        "total_tokens": 1429,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (M₁). Here's the analysis:\n\n### Components and Configuration:\n1. **M₁ (MOSFET)**:\n   - Acts as the amplifying device.\n   - The gate is driven by the input signal \\( V_{in} \\) through the coupling capacitor \\( C_1 \\).\n   - The source is connected to ground.\n   - The drain is connected to \\( V_{DD} \\) through the load resistor \\( R_D \\).\n\n2. **\\( R_D \\)**:\n   - Acts as the load resistor.\n   - Converts the drain current into a voltage signal at \\( V_{out} \\).\n\n3. **\\( C_1 \\)**:\n   - A coupling capacitor that blocks DC components of \\( V_{in} \\) while allowing the AC signal to pass to the gate of the MOSFET.\n\n4. **\\( V_b \\)**:\n   - A DC bias voltage applied to the gate of the MOSFET to set its operating point in the saturation region.\n\n5. **\\( V_{DD} \\)**:\n   - The supply voltage for the circuit.\n\n6. **\\( V_{out} \\)**:\n   - The output voltage, taken from the drain of the MOSFET.\n\n---\n\n### Operation:\n1. **Biasing**:\n   - The gate of the MOSFET is biased with \\( V_b \\) to ensure the MOSFET operates in the saturation region for amplification.\n   - The coupling capacitor \\( C_1 \\) ensures that the AC input signal \\( V_{in} \\) is superimposed on the DC bias voltage \\( V_b \\).\n\n2. **Amplification**:\n   - The input signal \\( V_{in} \\) modulates the gate voltage of the MOSFET.\n   - This causes variations in the drain current \\( I_D \\), which flows through \\( R_D \\).\n   - The voltage drop across \\( R_D \\) creates the output voltage \\( V_{out} \\), which is an amplified version of \\( V_{in} \\) (inverted due to the common-source configuration).\n\n3. **AC Analysis**:\n   - The small-signal voltage gain \\( A_v \\) is approximately:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of the MOSFET.\n\n4. **Input and Output Impedance**:\n   - The input impedance is high due to the MOSFET's gate.\n   - The output impedance is approximately \\( R_D \\).\n\n---\n\n### Key Points:\n- The circuit inverts the input signal (180° phase shift).\n- The gain depends on \\( g_m \\) and \\( R_D \\).\n- Proper biasing is crucial to ensure the MOSFET operates in the saturation region for linear amplification.\n- The coupling capacitor \\( C_1 \\) ensures that the DC biasing is not affected by the input signal.\n\nThis circuit is commonly used in analog signal processing for amplification purposes.",
        "format": "markdown",
        "sha256": "53fcb787e8185934ef3ba4327eae430240b50dce5baa4e354b6b07fc41dc61e6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the input as being applied to the gate and treats the circuit as a common-source amplifier, missing that Vin is applied to the source node shorted to ground. Its gain conclusion is therefore based on the wrong topology.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 632,
        "total_tokens": 1412,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 632,
        "total_tokens": 1412,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (M₁). Here's the analysis:\n\n---\n\n### **Components and Configuration**\n1. **MOSFET (M₁):**\n   - Acts as the amplifying device.\n   - The gate is driven by the input signal \\( V_{in} \\) through the coupling capacitor \\( C_1 \\).\n   - The source is grounded.\n   - The drain is connected to \\( V_{DD} \\) through the load resistor \\( R_D \\).\n\n2. **\\( R_D \\):**\n   - Acts as the load resistor.\n   - Converts the drain current into an output voltage \\( V_{out} \\).\n\n3. **\\( C_1 \\):**\n   - A coupling capacitor that blocks DC components of \\( V_{in} \\) and allows only the AC signal to pass to the gate of the MOSFET.\n\n4. **\\( V_b \\):**\n   - A bias voltage applied to the gate of the MOSFET to set the operating point (quiescent point).\n\n5. **\\( V_{DD} \\):**\n   - The supply voltage for the circuit.\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The gate of the MOSFET is biased at \\( V_b \\) to ensure the MOSFET operates in the saturation region for amplification.\n   - The bias voltage \\( V_b \\) is chosen such that \\( V_{GS} > V_{th} \\), where \\( V_{th} \\) is the threshold voltage of the MOSFET.\n\n2. **Signal Amplification:**\n   - The input signal \\( V_{in} \\) is superimposed on the bias voltage \\( V_b \\) via \\( C_1 \\).\n   - The small variations in \\( V_{in} \\) cause changes in the drain current \\( I_D \\), which are converted into voltage variations across \\( R_D \\).\n   - The output voltage \\( V_{out} \\) is taken from the drain and is inverted with respect to the input signal due to the common-source configuration.\n\n3. **AC Analysis:**\n   - The small-signal gain of the amplifier is approximately:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of the MOSFET, given by:\n     \\[\n     g_m = \\frac{2I_{D,Q}}{V_{GS} - V_{th}}\n     \\]\n     \\( I_{D,Q} \\) is the quiescent drain current.\n\n4. **Coupling Capacitor \\( C_1 \\):**\n   - Blocks the DC component of \\( V_{in} \\) and ensures only the AC signal is amplified.\n   - Its value is chosen to ensure a low reactance at the operating frequency.\n\n---\n\n### **Key Points**\n- **Voltage Gain:** The circuit provides a high voltage gain, determined by \\( g_m \\) and \\( R_D \\).\n- **Inversion:** The output signal is inverted with respect to the input signal.\n- **Frequency Response:** The coupling capacitor \\( C_1 \\) and the parasitic capacitances of the MOSFET affect the frequency response of the amplifier.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing, such as audio amplification and RF circuits.",
        "format": "markdown",
        "sha256": "7e661a849aed647dbd4c4445c1b92b5c72f935a06c4a53b54b36e3b4dd179774"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the topology, placing the input at the gate instead of the source, and misses that the source node is shorted to ground. Thus the input is shorted and the ideal gain is zero, not a common-source gain of \\(-g_mR_D\\).",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 699,
        "total_tokens": 1479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 699,
        "total_tokens": 1479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier** using a MOSFET (M₁). Here's the analysis:\n\n---\n\n### **Components and Configuration**\n1. **MOSFET (M₁):**\n   - Acts as the amplifying device.\n   - The gate is driven by the input signal \\( V_{in} \\) through the coupling capacitor \\( C_1 \\).\n   - The source is grounded.\n   - The drain is connected to \\( V_{DD} \\) through the load resistor \\( R_D \\).\n\n2. **\\( R_D \\):**\n   - Acts as the load resistor.\n   - Converts the drain current into an output voltage \\( V_{out} \\).\n\n3. **\\( C_1 \\):**\n   - A coupling capacitor that blocks DC components of \\( V_{in} \\) and allows only the AC signal to pass to the gate of the MOSFET.\n\n4. **\\( V_b \\):**\n   - A DC bias voltage applied to the gate of the MOSFET to set its operating point in the saturation region.\n\n5. **\\( V_{DD} \\):**\n   - The supply voltage.\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The gate of the MOSFET is biased with \\( V_b \\) to ensure the MOSFET operates in the saturation region, which is necessary for amplification.\n\n2. **Signal Amplification:**\n   - The input signal \\( V_{in} \\) is coupled to the gate of the MOSFET through \\( C_1 \\).\n   - The small variations in \\( V_{in} \\) modulate the gate voltage, causing changes in the drain current \\( I_D \\).\n   - These changes in \\( I_D \\) produce a corresponding voltage drop across \\( R_D \\), resulting in an amplified output voltage \\( V_{out} \\).\n\n3. **Output Voltage:**\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n   - The small-signal gain of the amplifier is approximately:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of the MOSFET.\n\n---\n\n### **Key Points**\n- The circuit inverts the input signal because of the negative gain (\\( A_v < 0 \\)).\n- The coupling capacitor \\( C_1 \\) ensures that the DC biasing of the MOSFET is not affected by the input signal source.\n- Proper selection of \\( V_b \\), \\( R_D \\), and \\( C_1 \\) is crucial for optimal operation.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing, such as audio amplifiers and RF amplifiers, where signal amplification is required.",
        "format": "markdown",
        "sha256": "0734b27f8c4f7a5b9a53c6524ff39bf39a0a1fbf23b02184cb0e1ebebbc2fa47"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the input as applied to the gate and treats the source as simply grounded, missing that Vin is applied to the source node that is hard-shorted to ground. Its common-source gain analysis is therefore based on the wrong topology.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 594,
        "total_tokens": 1374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 594,
        "total_tokens": 1374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a common-source amplifier with parasitic capacitances. The poles of the circuit are determined by the RC time constants formed by the resistances and capacitances in the circuit. \n\nThe circuit has the following capacitances:\n\n1. **\\(C_{GS}\\)**: Gate-to-source capacitance.\n2. **\\(C_{GD}\\)**: Gate-to-drain capacitance.\n3. **\\(C_{DB}\\)**: Drain-to-bulk capacitance.\n4. **\\(C_{SB}\\)**: Source-to-bulk capacitance.\n\nEach of these capacitances, in combination with the resistances in the circuit (\\(R_S\\), \\(R_D\\), and the transistor's internal resistances), contributes to a pole in the frequency response.\n\n### Total Number of Poles:\nThe circuit has **4 poles**, corresponding to the 4 capacitances (\\(C_{GS}\\), \\(C_{GD}\\), \\(C_{DB}\\), and \\(C_{SB}\\)).",
        "format": "markdown",
        "sha256": "1a9de29d77bb0b4e60e0bc5fceaf07f267e62eb34cfa754c12d07469e1b656a5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer identifies the common-source stage and its capacitances, but incorrectly assigns one pole to each capacitor. In this circuit, CSB is shorted out and only two capacitor voltages are independent, so there are two poles.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 204,
        "total_tokens": 988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 204,
        "total_tokens": 988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a common-source amplifier with parasitic capacitances. The poles of the circuit are determined by the RC time constants formed by the resistances and capacitances in the circuit. \n\n### Capacitances in the circuit:\n1. **\\( C_{GS} \\)**: Gate-to-source capacitance.\n2. **\\( C_{GD} \\)**: Gate-to-drain capacitance.\n3. **\\( C_{DB} \\)**: Drain-to-bulk capacitance.\n4. **\\( C_{SB} \\)**: Source-to-bulk capacitance.\n\nEach of these capacitances, in combination with the resistances in the circuit (\\( R_S \\), \\( R_D \\), and the transistor's internal resistances), contributes to a pole in the frequency response.\n\n### Number of Poles:\nThe circuit has **four poles**, corresponding to the four capacitances (\\( C_{GS} \\), \\( C_{GD} \\), \\( C_{DB} \\), and \\( C_{SB} \\)). However, depending on the circuit's design and operating conditions, some poles may dominate while others may have negligible effects.",
        "format": "markdown",
        "sha256": "9006f6cd81c38d04cf9ef0c6ec3a70011a0f962bd52c36507e2d4ce4585c070b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The conclusion of four poles is incorrect: CSB is shorted out because its terminals are grounded, and only two capacitor voltages are independent. The answer identifies the common-source stage and relevant capacitors but wrongly assigns one pole to each capacitor.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 233,
        "total_tokens": 1017,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 233,
        "total_tokens": 1017,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a common-source amplifier with parasitic capacitances. The poles in the circuit are determined by the RC time constants formed by the resistances and capacitances in the circuit. \n\n### Key capacitances:\n1. **\\( C_{GS} \\)**: Gate-to-source capacitance.\n2. **\\( C_{GD} \\)**: Gate-to-drain capacitance.\n3. **\\( C_{DB} \\)**: Drain-to-bulk capacitance.\n4. **\\( C_{SB} \\)**: Source-to-bulk capacitance.\n\n### Key resistances:\n1. **\\( R_S \\)**: Source resistance.\n2. **\\( R_D \\)**: Drain resistance.\n\n### Poles:\nEach RC combination introduces a pole in the circuit. The poles are associated with the following:\n1. The \\( C_{GS} \\) and \\( R_S \\) combination.\n2. The \\( C_{GD} \\) and the equivalent resistance seen at the gate and drain.\n3. The \\( C_{DB} \\) and \\( R_D \\) combination.\n4. The \\( C_{SB} \\) and the source resistance.\n\nThus, the circuit has **four poles**.",
        "format": "markdown",
        "sha256": "cf2f8ba1b87bf82685ec256b4fe30433a44b8d01fc0b4ca081c34ee7d1e11050"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer identifies the common-source stage and its capacitances, but incorrectly assigns a pole to each RC combination. The grounded-source capacitance is shorted out, and the remaining capacitor voltages are not all independent; the circuit has two poles, not four.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 248,
        "total_tokens": 1032,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 248,
        "total_tokens": 1032,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source MOSFET amplifier** with a resistive divider for biasing. Here's a detailed analysis:\n\n---\n\n### **Components and Configuration**\n1. **MOSFET (M1):**\n   - Acts as the amplifying device.\n   - The gate voltage \\( V_F \\) determines the operating region of the MOSFET.\n\n2. **Resistors \\( R_1 \\) and \\( R_2 \\):**\n   - Form a voltage divider to set the gate voltage \\( V_F \\).\n   - \\( V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2} \\).\n\n3. **Resistor \\( R_D \\):**\n   - Acts as the load resistor.\n   - Converts the drain current \\( I_D \\) into an output voltage \\( V_{out} \\).\n\n4. **Input Voltage \\( V_{in} \\):**\n   - Applied to the gate of the MOSFET.\n   - Modulates the drain current \\( I_D \\), which in turn affects \\( V_{out} \\).\n\n5. **Output Voltage \\( V_{out} \\):**\n   - Taken from the drain of the MOSFET.\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The voltage divider formed by \\( R_1 \\) and \\( R_2 \\) sets the gate voltage \\( V_F \\).\n   - \\( V_F \\) determines the operating point of the MOSFET (cutoff, triode, or saturation region).\n\n2. **Amplification:**\n   - When \\( V_{in} \\) is applied, it modulates the gate voltage \\( V_G \\), causing a change in the drain current \\( I_D \\).\n   - The change in \\( I_D \\) produces a corresponding change in \\( V_{out} \\) across \\( R_D \\).\n\n3. **Output Voltage:**\n   - \\( V_{out} = V_{DD} - I_D R_D \\).\n   - \\( I_D \\) depends on the MOSFET's operating region and the gate-source voltage \\( V_{GS} \\).\n\n---\n\n### **Key Equations**\n1. **Voltage Divider:**\n   \\[\n   V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2}\n   \\]\n\n2. **Drain Current in Saturation:**\n   \\[\n   I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n   \\]\n   where:\n   - \\( k_n = \\mu_n C_{ox} \\frac{W}{L} \\) (process-dependent constant),\n   - \\( V_{GS} = V_F + V_{in} \\),\n   - \\( V_{th} \\) is the threshold voltage.\n\n3. **Output Voltage:**\n   \\[\n   V_{out} = V_{DD} - I_D R_D\n   \\]\n\n---\n\n### **Design Considerations**\n1. **Biasing Stability:**\n   - The resistors \\( R_1 \\) and \\( R_2 \\) should be chosen to ensure the MOSFET operates in the saturation region for proper amplification.\n\n2. **Gain:**\n   - The small-signal voltage gain is approximately:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m = \\frac{\\partial I_D}{\\partial V_{GS}} \\) is the transconductance.\n\n3. **Input Impedance:**\n   - High, as the gate of the MOSFET draws negligible current.\n\n4. **Output Impedance:**\n   - Determined by \\( R_D \\) in parallel with the MOSFET's output resistance.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal amplification, such as audio amplifiers or sensor signal conditioning.",
        "format": "markdown",
        "sha256": "6b72429bbbd882a15027bc2ce06e732705be11f458f4dfe250f3ec187ed00777"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the topology: the input is at M1’s source, and R1–R2 feed the output back to the gate. Treating the divider as fixed bias and predicting a gate-input common-source gain of −gmRD misses the central negative-feedback mechanism.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 813,
        "total_tokens": 1593,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 813,
        "total_tokens": 1593,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source MOSFET amplifier** with a resistive divider for biasing. Here's a detailed analysis:\n\n---\n\n### **Components and Configuration**\n1. **MOSFET (M1):**\n   - Acts as the amplifying device.\n   - The gate voltage \\( V_F \\) determines the operating region of the MOSFET.\n\n2. **Resistors \\( R_1 \\) and \\( R_2 \\):**\n   - Form a voltage divider to set the gate voltage \\( V_F \\).\n   - \\( V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2} \\).\n\n3. **Resistor \\( R_D \\):**\n   - Acts as the load resistor.\n   - Converts the drain current \\( I_D \\) into an output voltage \\( V_{out} \\).\n\n4. **Input Voltage \\( V_{in} \\):**\n   - Applied to the gate of the MOSFET.\n   - Modulates the drain current \\( I_D \\), which in turn affects \\( V_{out} \\).\n\n5. **Output Voltage \\( V_{out} \\):**\n   - Taken from the drain of the MOSFET.\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The voltage divider formed by \\( R_1 \\) and \\( R_2 \\) sets the gate voltage \\( V_F \\).\n   - \\( V_F \\) determines the operating point of the MOSFET (cutoff, triode, or saturation region).\n\n2. **Amplification:**\n   - When \\( V_{in} \\) is applied, it modulates the gate voltage \\( V_G \\), causing a change in the drain current \\( I_D \\).\n   - The change in \\( I_D \\) produces a corresponding change in \\( V_{out} \\) across \\( R_D \\).\n\n3. **Output Voltage:**\n   - \\( V_{out} = V_{DD} - I_D R_D \\).\n   - \\( I_D \\) depends on the MOSFET's operating region and the gate-source voltage \\( V_{GS} \\).\n\n---\n\n### **Key Equations**\n1. **Gate Voltage:**\n   \\[\n   V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2}\n   \\]\n\n2. **Drain Current (in saturation):**\n   \\[\n   I_D = \\frac{1}{2} k_n (V_{GS} - V_{th})^2\n   \\]\n   where:\n   - \\( k_n \\) is the MOSFET's transconductance parameter.\n   - \\( V_{GS} = V_F + V_{in} \\).\n   - \\( V_{th} \\) is the MOSFET's threshold voltage.\n\n3. **Output Voltage:**\n   \\[\n   V_{out} = V_{DD} - I_D R_D\n   \\]\n\n---\n\n### **Design Considerations**\n1. **Biasing Stability:**\n   - The resistors \\( R_1 \\) and \\( R_2 \\) should be chosen to ensure the MOSFET operates in the saturation region for proper amplification.\n\n2. **Gain:**\n   - The voltage gain \\( A_v \\) is approximately:\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m = \\frac{\\partial I_D}{\\partial V_{GS}} \\) is the MOSFET's transconductance.\n\n3. **Input and Output Impedance:**\n   - Input impedance is high due to the MOSFET's gate.\n   - Output impedance is approximately \\( R_D \\).\n\n---\n\n### **Applications**\nThis circuit is commonly used in:\n- Small-signal amplification.\n- Analog signal processing.\n- Audio amplifiers.",
        "format": "markdown",
        "sha256": "5bb81f5635be316e635b09b110b205df211f99cb69168f01b0b075ceb0abee94"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer misses the essential topology: Vin is applied at the source, and the R1–R2 divider feeds Vout back to the gate as negative feedback. Its common-source, gate-input model and gain are therefore wrong; it earns limited credit for recognizing the MOSFET drain output and load resistor.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 799,
        "total_tokens": 1579,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 799,
        "total_tokens": 1579,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source MOSFET amplifier** with a resistive divider for biasing. Here's a detailed analysis:\n\n---\n\n### **Components and Configuration**\n1. **MOSFET (M₁):**\n   - Acts as the amplifying device.\n   - The gate voltage \\( V_F \\) determines the operating region of the MOSFET.\n\n2. **Resistors \\( R_1 \\) and \\( R_2 \\):**\n   - Form a voltage divider to set the gate voltage \\( V_F \\).\n   - \\( V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2} \\).\n\n3. **Resistor \\( R_D \\):**\n   - Acts as the load resistor.\n   - Converts the drain current \\( I_D \\) into an output voltage \\( V_{out} \\).\n\n4. **Input Voltage \\( V_{in} \\):**\n   - Applied to the gate of the MOSFET.\n   - Modulates the drain current \\( I_D \\), which in turn affects \\( V_{out} \\).\n\n5. **Output Voltage \\( V_{out} \\):**\n   - Taken from the drain of the MOSFET.\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - The voltage divider formed by \\( R_1 \\) and \\( R_2 \\) sets the gate voltage \\( V_F \\).\n   - \\( V_F \\) determines the operating point of the MOSFET (cutoff, triode, or saturation region).\n\n2. **Amplification:**\n   - When \\( V_{in} \\) is applied, it modulates the gate voltage \\( V_G \\), causing variations in the drain current \\( I_D \\).\n   - The drain current \\( I_D \\) flows through \\( R_D \\), creating a voltage drop across it.\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_D \\cdot R_D\n     \\]\n\n3. **Small-Signal Analysis:**\n   - For small variations in \\( V_{in} \\), the MOSFET operates in the saturation region, and the small-signal gain is approximately:\n     \\[\n     A_v = -g_m \\cdot R_D\n     \\]\n     where \\( g_m \\) is the transconductance of the MOSFET.\n\n---\n\n### **Key Equations**\n1. **Gate Voltage (\\( V_F \\)):**\n   \\[\n   V_F = V_{DD} \\cdot \\frac{R_2}{R_1 + R_2}\n   \\]\n\n2. **Output Voltage (\\( V_{out} \\)):**\n   \\[\n   V_{out} = V_{DD} - I_D \\cdot R_D\n   \\]\n\n3. **Small-Signal Gain (\\( A_v \\)):**\n   \\[\n   A_v = -g_m \\cdot R_D\n   \\]\n\n---\n\n### **Design Considerations**\n1. **Biasing Stability:**\n   - The values of \\( R_1 \\) and \\( R_2 \\) should be chosen to ensure the MOSFET operates in the saturation region for proper amplification.\n\n2. **Load Resistance (\\( R_D \\)):**\n   - A higher \\( R_D \\) increases the gain but reduces the output swing.\n\n3. **Input Signal:**\n   - The input signal \\( V_{in} \\) should be small enough to keep the MOSFET in the saturation region.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal amplification, such as in audio amplifiers or sensor signal conditioning.",
        "format": "markdown",
        "sha256": "e6e99d32d93d99309a4518df1782dcccedf5b40ee63d0f5683ffe66c1f468f58"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer misses the source-input, output-to-gate feedback topology: it treats the circuit as a common-source stage with gate input and gives an inverting gain. Only generic MOSFET amplifier observations are relevant.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 771,
        "total_tokens": 1551,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 771,
        "total_tokens": 1551,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's the analysis:\n\n### Components:\n1. **M1**: The main transistor (common-source configuration) amplifies the input signal \\( V_{in} \\).\n2. **M2**: The active load transistor operates as a current source, providing a high output impedance to improve gain.\n3. **\\( V_b \\)**: The bias voltage applied to the gate of \\( M_2 \\) sets the current through \\( M_2 \\), which also flows through \\( M_1 \\).\n4. **\\( V_{DD} \\)**: The supply voltage.\n\n---\n\n### Operation:\n1. **Input Signal**:\n   - \\( V_{in} \\) is applied to the gate of \\( M_1 \\). This modulates the drain current of \\( M_1 \\), which is mirrored by \\( M_2 \\).\n\n2. **Active Load**:\n   - \\( M_2 \\) is biased in saturation mode by \\( V_b \\), acting as a constant current source. This increases the output impedance at \\( V_{out} \\), enhancing the voltage gain.\n\n3. **Output Voltage**:\n   - The output voltage \\( V_{out} \\) is taken at the drain of \\( M_1 \\). It is inversely related to the input voltage \\( V_{in} \\), as \\( M_1 \\) operates in the common-source configuration.\n\n---\n\n### Key Equations:\n1. **Voltage Gain**:\n   \\[\n   A_v = -g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n   - \\( R_{out} \\): Output resistance, primarily determined by \\( M_2 \\) in saturation mode.\n\n2. **Output Resistance**:\n   \\[\n   R_{out} \\approx r_{o2} \\parallel r_{o1}\n   \\]\n   where:\n   - \\( r_{o1} \\): Output resistance of \\( M_1 \\).\n   - \\( r_{o2} \\): Output resistance of \\( M_2 \\).\n\n3. **Bias Current**:\n   - The current through \\( M_1 \\) and \\( M_2 \\) is set by \\( V_b \\) and the characteristics of \\( M_2 \\).\n\n---\n\n### Design Considerations:\n1. **Biasing**:\n   - \\( V_b \\) must be chosen such that \\( M_2 \\) operates in saturation mode.\n   - \\( V_{in} \\) must ensure \\( M_1 \\) operates in saturation mode for proper amplification.\n\n2. **Gain**:\n   - High gain is achieved by maximizing \\( g_{m1} \\) (transconductance of \\( M_1 \\)) and \\( R_{out} \\) (output resistance).\n\n3. **Frequency Response**:\n   - The circuit's bandwidth is limited by parasitic capacitances at the output node.\n\n---\n\n### Applications:\nThis circuit is commonly used in analog integrated circuits for amplification purposes, such as in operational amplifiers or as a building block in more complex analog designs.",
        "format": "markdown",
        "sha256": "812384668d5e5efda1f007beaeb7fa2de33d9b25e5cb83933e5e406268d2c139"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the circuit as a common-source amplifier; M1 is a source follower with output at its source, giving positive gain near unity, not an inverting high-gain stage.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 663,
        "total_tokens": 1443,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 663,
        "total_tokens": 1443,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: The main transistor (common-source amplifier).\n2. **M2**: The active load transistor, operating as a current source.\n3. **\\( V_{in} \\)**: Input voltage applied to the gate of \\( M_1 \\).\n4. **\\( V_b \\)**: Bias voltage applied to the gate of \\( M_2 \\), setting its operating point.\n5. **\\( V_{DD} \\)**: Supply voltage.\n6. **\\( V_{out} \\)**: Output voltage.\n\n---\n\n### Operation:\n1. **M1 (Amplifier)**:\n   - \\( M_1 \\) is configured as a common-source amplifier.\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M_1 \\), controlling its drain current.\n   - The output voltage \\( V_{out} \\) is taken at the drain of \\( M_1 \\).\n\n2. **M2 (Active Load)**:\n   - \\( M_2 \\) is configured as a current source, providing a constant current to \\( M_1 \\).\n   - The gate of \\( M_2 \\) is biased with \\( V_b \\), which sets the current through \\( M_2 \\).\n   - \\( M_2 \\) operates in the saturation region, where its drain current is relatively constant.\n\n3. **Amplification**:\n   - The small-signal input \\( V_{in} \\) causes a change in the drain current of \\( M_1 \\), which in turn causes a voltage swing at \\( V_{out} \\).\n   - The active load \\( M_2 \\) provides a high output impedance, increasing the voltage gain of the circuit.\n\n---\n\n### Key Equations:\n1. **Voltage Gain**:\n   \\[\n   A_v = -g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n   - \\( R_{out} \\): Output resistance, primarily determined by \\( M_2 \\) in saturation.\n\n2. **Output Resistance**:\n   \\[\n   R_{out} \\approx r_{o2}\n   \\]\n   where \\( r_{o2} \\) is the output resistance of \\( M_2 \\) in saturation.\n\n3. **Biasing**:\n   - \\( V_b \\) sets the operating point of \\( M_2 \\), ensuring it remains in saturation.\n   - \\( V_{DD} \\) provides the supply voltage for the circuit.\n\n---\n\n### Design Considerations:\n1. **Bias Voltage \\( V_b \\)**:\n   - \\( V_b \\) must be chosen such that \\( M_2 \\) operates in saturation.\n   - \\( V_b > V_{th2} \\), where \\( V_{th2} \\) is the threshold voltage of \\( M_2 \\).\n\n2. **Operating Regions**:\n   - \\( M_1 \\) operates in saturation for proper amplification.\n   - \\( M_2 \\) operates in saturation to act as a current source.\n\n3. **Gain**:\n   - The gain depends on \\( g_{m1} \\) and \\( r_{o2} \\). A higher \\( g_{m1} \\) (achieved by increasing the bias current) and a higher \\( r_{o2} \\) (achieved by proper sizing of \\( M_2 \\)) result in higher gain.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing, such as in amplifiers and operational transconductance amplifiers (OTAs).\n- The active load improves gain and reduces power consumption compared to a resistive load.",
        "format": "markdown",
        "sha256": "95c1161e06afd08564f9b2f392475e8cdb55847ee0b8ffb1aa9ff1071fdd150d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the source follower as a common-source amplifier, places the output at the wrong terminal, and gives an inverting gain. The golden solution explicitly assigns 0 for this topology error.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 796,
        "total_tokens": 1576,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 796,
        "total_tokens": 1576,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: The main transistor (common-source configuration) that amplifies the input signal \\( V_{in} \\).\n2. **M2**: The active load transistor, which operates as a current source. Its gate is biased by \\( V_b \\), setting the current through the circuit.\n3. **\\( V_{DD} \\)**: The supply voltage.\n4. **\\( V_{out} \\)**: The output voltage.\n\n---\n\n### Operation:\n1. **Input Signal (\\( V_{in} \\))**:\n   - \\( V_{in} \\) is applied to the gate of \\( M_1 \\). This controls the current flowing through \\( M_1 \\) (drain current \\( I_{D1} \\)).\n   - \\( M_1 \\) operates in the saturation region for proper amplification.\n\n2. **Active Load (\\( M_2 \\))**:\n   - \\( M_2 \\) is configured as a current source. Its gate is biased with a constant voltage \\( V_b \\), ensuring that \\( M_2 \\) operates in the saturation region.\n   - The current through \\( M_2 \\) (drain current \\( I_{D2} \\)) is approximately constant and equal to \\( I_{D1} \\) (assuming ideal conditions).\n\n3. **Output Voltage (\\( V_{out} \\))**:\n   - The output voltage is taken at the drain of \\( M_1 \\), which is also the drain of \\( M_2 \\).\n   - As \\( V_{in} \\) increases, the current through \\( M_1 \\) increases, causing a larger voltage drop across \\( M_2 \\). This reduces \\( V_{out} \\), resulting in an inverted output signal.\n\n---\n\n### Key Characteristics:\n1. **Gain**:\n   - The voltage gain \\( A_v \\) is approximately:\n     \\[\n     A_v = -g_{m1} \\cdot r_{o1} \\parallel r_{o2}\n     \\]\n     where:\n     - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n     - \\( r_{o1} \\): Output resistance of \\( M_1 \\).\n     - \\( r_{o2} \\): Output resistance of \\( M_2 \\).\n\n2. **Input Impedance**:\n   - The input impedance is high because the gate of \\( M_1 \\) is insulated (MOSFET property).\n\n3. **Output Impedance**:\n   - The output impedance is determined by the parallel combination of \\( r_{o1} \\) and \\( r_{o2} \\).\n\n4. **Biasing**:\n   - Proper biasing of \\( M_1 \\) and \\( M_2 \\) ensures that both transistors operate in the saturation region.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing, such as amplifiers in integrated circuits, due to its high gain and compact design.",
        "format": "markdown",
        "sha256": "237553dcbfbc5ae1bc60ff8df7fd996db616471796488e127c89e429e39b0378"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the circuit as a common-source amplifier with an active load and gives an inverting gain. It is a source follower with positive gain at or slightly below unity.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 644,
        "total_tokens": 1424,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 644,
        "total_tokens": 1424,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_1\\)) and a p-channel MOSFET (\\(M_2\\)). Here's the analysis:\n\n---\n\n### **Circuit Description**\n1. **MOSFET \\(M_1\\) (n-channel):**\n   - The source is connected to ground.\n   - The drain is connected to the output (\\(V_{out}\\)).\n   - The gate is connected to the input (\\(V_{in}\\)).\n\n2. **MOSFET \\(M_2\\) (p-channel):**\n   - The source is connected to \\(V_{DD}\\) (supply voltage).\n   - The drain is connected to the output (\\(V_{out}\\)).\n   - The gate is connected to the input (\\(V_{in}\\)).\n\n---\n\n### **Operation**\nThe circuit operates as follows, depending on the input voltage (\\(V_{in}\\)):\n\n1. **When \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (n-channel) is OFF because the gate-source voltage (\\(V_{GS}\\)) is 0.\n   - \\(M_2\\) (p-channel) is ON because the gate-source voltage (\\(V_{SG}\\)) is \\(V_{DD}\\).\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic HIGH).\n\n2. **When \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (n-channel) is ON because the gate-source voltage (\\(V_{GS}\\)) is \\(V_{DD}\\).\n   - \\(M_2\\) (p-channel) is OFF because the gate-source voltage (\\(V_{SG}\\)) is 0.\n   - The output (\\(V_{out}\\)) is pulled down to ground (logic LOW).\n\n---\n\n### **Key Characteristics**\n1. **Inversion:**\n   - The circuit inverts the input signal. A LOW input produces a HIGH output, and a HIGH input produces a LOW output.\n\n2. **Power Consumption:**\n   - The circuit consumes negligible power in steady states (when \\(V_{in}\\) is either 0 or \\(V_{DD}\\)).\n   - Power is consumed only during switching (when \\(V_{in}\\) transitions between 0 and \\(V_{DD}\\)).\n\n3. **High Noise Margin:**\n   - CMOS inverters have high noise margins, making them robust against noise in digital circuits.\n\n4. **Fast Switching:**\n   - CMOS inverters are capable of fast switching due to the complementary operation of \\(M_1\\) and \\(M_2\\).\n\n---\n\n### **Applications**\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory devices, and other integrated circuits.",
        "format": "markdown",
        "sha256": "82c6d956c295251e9cca46347f0c07a3d8525eb7c65bc53ff98b0a9949ca91f1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter and its NMOS pull-down, PMOS pull-up, connections, and logic operation. The extra analysis is consistent with the circuit.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 621,
        "total_tokens": 1061,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 621,
        "total_tokens": 1061,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_1\\)) and a p-channel MOSFET (\\(M_2\\)), connected in a complementary configuration. Here's the analysis:\n\n---\n\n### **Circuit Description:**\n1. **Input (\\(V_{in}\\)):**\n   - The input voltage is applied to the gates of both transistors (\\(M_1\\) and \\(M_2\\)).\n\n2. **Output (\\(V_{out}\\)):**\n   - The output is taken from the common drain connection of \\(M_1\\) and \\(M_2\\).\n\n3. **Power Supply (\\(V_{DD}\\)):**\n   - The source of \\(M_2\\) is connected to \\(V_{DD}\\), the positive supply voltage.\n   - The source of \\(M_1\\) is connected to ground.\n\n---\n\n### **Operation:**\nThe circuit operates in two states depending on the input voltage (\\(V_{in}\\)):\n\n#### **1. \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (nMOS) is OFF because its gate-source voltage (\\(V_{GS1}\\)) is 0.\n   - \\(M_2\\) (pMOS) is ON because its gate-source voltage (\\(V_{GS2}\\)) is negative (\\(-V_{DD}\\)).\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) through \\(M_2\\).\n\n   **Output: High (\\(V_{out} = V_{DD}\\))**\n\n#### **2. \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (nMOS) is ON because its gate-source voltage (\\(V_{GS1}\\)) is \\(V_{DD}\\).\n   - \\(M_2\\) (pMOS) is OFF because its gate-source voltage (\\(V_{GS2}\\)) is 0.\n   - The output (\\(V_{out}\\)) is pulled down to ground through \\(M_1\\).\n\n   **Output: Low (\\(V_{out} = 0\\))**\n\n---\n\n### **Key Characteristics:**\n1. **Inversion:**\n   - The circuit inverts the input signal. A low input produces a high output, and a high input produces a low output.\n\n2. **Power Consumption:**\n   - The circuit consumes negligible power in steady states (when \\(V_{in}\\) is either 0 or \\(V_{DD}\\)) because only one transistor conducts at a time.\n   - Power is consumed during switching due to transient currents and charging/discharging of the output capacitance.\n\n3. **High Noise Margin:**\n   - CMOS inverters have high noise margins, making them robust against noise in digital circuits.\n\n4. **Fast Switching:**\n   - CMOS inverters are capable of fast switching due to the complementary operation of \\(M_1\\) and \\(M_2\\).\n\n---\n\n### **Applications:**\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory, and other integrated circuits.",
        "format": "markdown",
        "sha256": "834f1f6c5aca6264b519bffce823ed06d9bce425a209f459fc1eb9716bc456d8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, its NMOS pull-down and PMOS pull-up, and their complementary operation. The extra power and switching comments do not contradict the circuit's operation.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 684,
        "total_tokens": 1124,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 684,
        "total_tokens": 1124,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_1\\)) and a p-channel MOSFET (\\(M_2\\)). Here's the analysis:\n\n---\n\n### **Circuit Description**\n1. **MOSFET \\(M_1\\) (n-channel):**\n   - The source is connected to ground.\n   - The drain is connected to the output (\\(V_{out}\\)).\n   - The gate is connected to the input (\\(V_{in}\\)).\n\n2. **MOSFET \\(M_2\\) (p-channel):**\n   - The source is connected to \\(V_{DD}\\) (supply voltage).\n   - The drain is connected to the output (\\(V_{out}\\)).\n   - The gate is connected to the input (\\(V_{in}\\)).\n\n---\n\n### **Operation**\nThe circuit operates as follows, depending on the input voltage (\\(V_{in}\\)):\n\n1. **When \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (n-channel) is OFF because the gate-source voltage (\\(V_{GS}\\)) is 0.\n   - \\(M_2\\) (p-channel) is ON because the gate-source voltage (\\(V_{SG}\\)) is \\(V_{DD}\\).\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic HIGH).\n\n2. **When \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (n-channel) is ON because \\(V_{GS} = V_{DD}\\).\n   - \\(M_2\\) (p-channel) is OFF because \\(V_{SG} = 0\\).\n   - The output (\\(V_{out}\\)) is pulled down to ground (logic LOW).\n\n---\n\n### **Key Characteristics**\n- **Inversion:** The circuit inverts the input signal. A LOW input produces a HIGH output, and a HIGH input produces a LOW output.\n- **High Input Impedance:** The gates of the MOSFETs draw negligible current, making the circuit power-efficient.\n- **Low Power Consumption:** Power is consumed only during switching (when the input transitions between HIGH and LOW).\n\n---\n\n### **Applications**\n- CMOS inverters are widely used in:\n  - Digital logic gates (e.g., NAND, NOR, etc.).\n  - Microprocessors and digital circuits.\n  - Signal buffering and amplification.\n\nThis circuit is a simple yet powerful example of CMOS technology, which is the backbone of modern digital electronics.",
        "format": "markdown",
        "sha256": "98e2ed5525111413c7949472d21b52e7afcd5c0c84a6e7868ae4ed30be36069a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, its NMOS pull-down and PMOS pull-up connections, and its complementary operation.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 560,
        "total_tokens": 1000,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 560,
        "total_tokens": 1000,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, which is a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_2\\)) and a p-channel MOSFET (\\(M_1\\)). Here's the analysis:\n\n### Components:\n1. **\\(M_1\\)**: A p-channel MOSFET connected to \\(V_{DD}\\) (positive supply voltage).\n2. **\\(M_2\\)**: An n-channel MOSFET connected to ground (\\(GND\\)).\n3. **\\(V_{in}\\)**: Input voltage applied to the gates of both \\(M_1\\) and \\(M_2\\).\n4. **\\(V_{out}\\)**: Output voltage taken from the connection between \\(M_1\\) and \\(M_2\\).\n\n### Operation:\nThe circuit operates as follows, depending on the input voltage (\\(V_{in}\\)):\n\n1. **When \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (p-channel MOSFET) is **ON** because its gate-source voltage (\\(V_{GS}\\)) is negative.\n   - \\(M_2\\) (n-channel MOSFET) is **OFF** because its gate-source voltage (\\(V_{GS}\\)) is zero.\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic HIGH).\n\n2. **When \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (p-channel MOSFET) is **OFF** because its gate-source voltage (\\(V_{GS}\\)) is zero.\n   - \\(M_2\\) (n-channel MOSFET) is **ON** because its gate-source voltage (\\(V_{GS}\\)) is positive.\n   - The output (\\(V_{out}\\)) is pulled down to ground (\\(GND\\)) (logic LOW).\n\n### Key Characteristics:\n- **Inversion**: The circuit inverts the input signal. A low input produces a high output, and a high input produces a low output.\n- **High Noise Margin**: CMOS inverters have high noise margins, making them robust against noise.\n- **Low Power Consumption**: Power is consumed only during switching (when \\(V_{in}\\) transitions between high and low states).\n\n### Applications:\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory, and other digital systems. They form the basis of more complex logic gates and circuits.",
        "format": "markdown",
        "sha256": "c56bc9d7af10c11c88275f2b78c1c81bbc250e9616cbd624681b7ee1375349e0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as p-channel and analyzes the circuit as a complementary CMOS inverter. Both devices are NMOS, so the required device-identification gate assigns 0.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 548,
        "total_tokens": 988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 548,
        "total_tokens": 988,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, which is a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_2\\)) and a p-channel MOSFET (\\(M_1\\)). Here's the analysis:\n\n### Components:\n1. **\\(M_1\\)**: A p-channel MOSFET connected to \\(V_{DD}\\) (positive supply voltage).\n2. **\\(M_2\\)**: An n-channel MOSFET connected to ground.\n3. **\\(V_{in}\\)**: Input voltage applied to the gates of both \\(M_1\\) and \\(M_2\\).\n4. **\\(V_{out}\\)**: Output voltage taken from the connection between \\(M_1\\) and \\(M_2\\).\n\n### Operation:\nThe circuit operates as follows:\n1. **When \\(V_{in}\\) is low (close to 0V):**\n   - \\(M_1\\) (p-channel) is turned on because its gate-source voltage (\\(V_{GS}\\)) is negative.\n   - \\(M_2\\) (n-channel) is turned off because its \\(V_{GS}\\) is below the threshold voltage.\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) through \\(M_1\\).\n\n2. **When \\(V_{in}\\) is high (close to \\(V_{DD}\\)):**\n   - \\(M_1\\) (p-channel) is turned off because its \\(V_{GS}\\) is close to 0V.\n   - \\(M_2\\) (n-channel) is turned on because its \\(V_{GS}\\) is positive and above the threshold voltage.\n   - The output (\\(V_{out}\\)) is pulled down to ground through \\(M_2\\).\n\n### Key Characteristics:\n- **Inversion**: The circuit inverts the input signal. A low input produces a high output, and a high input produces a low output.\n- **High Input Impedance**: The gates of MOSFETs draw negligible current, making the circuit suitable for driving by other logic gates.\n- **Low Power Consumption**: In steady states (when \\(V_{in}\\) is either high or low), only one of the transistors conducts, minimizing power dissipation.\n\n### Applications:\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory, and other digital systems, due to their simplicity, low power consumption, and high speed.",
        "format": "markdown",
        "sha256": "04ffdc3911462c78b5da1bd0a5436011eff5790344395807acb1bcc3cfb91e90"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as a PMOS and analyzes the circuit as an ordinary CMOS inverter. The figure has two NMOS devices, so the golden solution's non-negotiable scoring gate requires 0.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 536,
        "total_tokens": 976,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 536,
        "total_tokens": 976,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, which is a fundamental building block in digital electronics. It consists of two MOSFETs: an n-channel MOSFET (\\(M_2\\)) and a p-channel MOSFET (\\(M_1\\)).\n\n### Key Components:\n1. **\\(M_1\\) (PMOS transistor):**\n   - Source is connected to \\(V_{DD}\\) (positive supply voltage).\n   - Drain is connected to the output (\\(V_{out}\\)).\n   - Gate is connected to the input (\\(V_{in}\\)).\n\n2. **\\(M_2\\) (NMOS transistor):**\n   - Source is connected to ground.\n   - Drain is connected to the output (\\(V_{out}\\)).\n   - Gate is connected to the input (\\(V_{in}\\)).\n\n### Operation:\nThe circuit operates as follows, depending on the input voltage (\\(V_{in}\\)):\n\n1. **When \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (PMOS) is ON because its gate-source voltage (\\(V_{GS}\\)) is negative.\n   - \\(M_2\\) (NMOS) is OFF because its gate-source voltage (\\(V_{GS}\\)) is zero.\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic HIGH).\n\n2. **When \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (PMOS) is OFF because its gate-source voltage (\\(V_{GS}\\)) is zero.\n   - \\(M_2\\) (NMOS) is ON because its gate-source voltage (\\(V_{GS}\\)) is positive.\n   - The output (\\(V_{out}\\)) is pulled down to ground (logic LOW).\n\n### Summary of Behavior:\n- The circuit inverts the input signal:\n  - \\(V_{in} = 0 \\rightarrow V_{out} = V_{DD}\\)\n  - \\(V_{in} = V_{DD} \\rightarrow V_{out} = 0\\)\n\n### Applications:\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory, and other digital systems, due to their low power consumption and high switching speed.",
        "format": "markdown",
        "sha256": "1947dbd6762511dce20b10addbcf4d2a92270bc0652bdc33d2cd0c2624baa4fb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as PMOS and analyzes the circuit as a conventional CMOS inverter. The golden solution explicitly requires both devices to be identified as NMOS; this error requires a score of 0.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 496,
        "total_tokens": 936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 440,
        "output_tokens": 496,
        "total_tokens": 936,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with an active load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: A MOSFET operating as the amplifying transistor.\n2. **M2**: A MOSFET operating as an active load (current source).\n3. **\\( V_{DD} \\)**: The supply voltage.\n4. **\\( V_{in} \\)**: The input voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: The output voltage taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **Amplification by \\( M_1 \\):**\n   - \\( M_1 \\) is configured as a common-source amplifier.\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M_1 \\), controlling its drain current \\( I_{D1} \\).\n   - The output voltage \\( V_{out} \\) is taken at the drain of \\( M_1 \\), and it is inversely related to \\( I_{D1} \\) due to the voltage drop across \\( M_2 \\).\n\n2. **Active Load \\( M_2 \\):**\n   - \\( M_2 \\) is configured as a current source.\n   - Its gate and drain are connected, forcing \\( M_2 \\) to operate in the saturation region.\n   - \\( M_2 \\) provides a high output impedance, improving the gain of the amplifier.\n\n---\n\n### Key Equations:\n1. **Output Voltage (\\( V_{out} \\)):**\n   \\[\n   V_{out} = V_{DD} - I_{D1} \\cdot R_{out}\n   \\]\n   where \\( R_{out} \\) is the effective output resistance of \\( M_2 \\).\n\n2. **Small-Signal Voltage Gain (\\( A_v \\)):**\n   \\[\n   A_v = -g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n   - \\( R_{out} \\): Output resistance of \\( M_2 \\), approximately \\( r_{o2} \\) (the small-signal output resistance of \\( M_2 \\)).\n\n3. **Output Resistance (\\( R_{out} \\)):**\n   \\[\n   R_{out} \\approx r_{o2}\n   \\]\n   \\( r_{o2} \\) is the small-signal output resistance of \\( M_2 \\), given by:\n   \\[\n   r_{o2} = \\frac{1}{\\lambda_2 I_{D2}}\n   \\]\n   where \\( \\lambda_2 \\) is the channel-length modulation parameter of \\( M_2 \\), and \\( I_{D2} \\) is the drain current of \\( M_2 \\).\n\n---\n\n### Advantages:\n1. **High Gain:** The active load \\( M_2 \\) provides a high output resistance, enhancing the voltage gain.\n2. **Compact Design:** The use of an active load eliminates the need for a large resistor, saving space in integrated circuits.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog integrated circuits, such as operational amplifiers and signal processing circuits, where high gain and compact design are required.",
        "format": "markdown",
        "sha256": "52ef8cdb363a4bd4916774223ce269b5f82b1ed3f2bd3853131a7358a5c8b0e8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes a common-source stage and notes that M2 is gate-drain connected, but treats the diode-connected load as a high-output-resistance current source. It therefore misses the dominant load impedance (approximately 1/gm2) and gives the wrong gain; the golden solution caps this misreading at 1.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 706,
        "total_tokens": 1486,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 706,
        "total_tokens": 1486,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with an active load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: A MOSFET operating as the amplifying transistor.\n2. **M2**: A MOSFET operating as an active load (current source).\n3. **\\( V_{DD} \\)**: The supply voltage.\n4. **\\( V_{in} \\)**: The input voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: The output voltage taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **Amplification by \\( M_1 \\):**\n   - \\( M_1 \\) is configured as a common-source amplifier.\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M_1 \\), controlling its drain current \\( I_{D1} \\).\n   - The output voltage \\( V_{out} \\) is taken at the drain of \\( M_1 \\), and it is inversely related to \\( I_{D1} \\) due to the voltage drop across \\( M_2 \\).\n\n2. **Active Load by \\( M_2 \\):**\n   - \\( M_2 \\) is configured as a current source, providing a high output impedance.\n   - The gate and drain of \\( M_2 \\) are connected, forcing \\( M_2 \\) to operate in the saturation region.\n   - This configuration ensures that \\( M_2 \\) provides a nearly constant current, improving the gain of the amplifier.\n\n---\n\n### Key Equations:\n1. **Output Voltage (\\( V_{out} \\)):**\n   \\[\n   V_{out} = V_{DD} - I_{D1} \\cdot R_{out}\n   \\]\n   where \\( R_{out} \\) is the output resistance of \\( M_2 \\).\n\n2. **Small-Signal Voltage Gain (\\( A_v \\)):**\n   \\[\n   A_v = -g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n   - \\( R_{out} \\): Output resistance of \\( M_2 \\), given by \\( r_{o2} \\), the small-signal output resistance of \\( M_2 \\).\n\n3. **Output Resistance (\\( R_{out} \\)):**\n   \\[\n   R_{out} = r_{o2}\n   \\]\n   \\( r_{o2} \\) is the small-signal output resistance of \\( M_2 \\), which is high due to the active load configuration.\n\n---\n\n### Advantages of the Circuit:\n1. **High Gain:**\n   - The active load \\( M_2 \\) provides a high output resistance, increasing the overall voltage gain.\n2. **Compact Design:**\n   - The use of an active load eliminates the need for a large resistor, saving space in integrated circuits.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog integrated circuits, such as operational amplifiers and signal processing circuits, where high gain and compact design are required.",
        "format": "markdown",
        "sha256": "fd020d19de5eb299ff279f512a999d46d022fea337e1fed81bf06367e36448a6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It identifies the common-source stage and notes M2's gate-drain connection, but incorrectly treats the diode-connected load as a high-output-resistance current source. The gain should be approximately -gm1/gm2, not -gm1·ro2.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 669,
        "total_tokens": 1449,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 669,
        "total_tokens": 1449,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with an active load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: A MOSFET operating as the amplifying transistor.\n2. **M2**: A MOSFET operating as an active load (current source).\n3. **\\( V_{DD} \\)**: The supply voltage.\n4. **\\( V_{in} \\)**: The input voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{out} \\)**: The output voltage taken from the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **M1 (Amplifying Transistor)**:\n   - \\( M_1 \\) is configured in a common-source configuration.\n   - The input signal \\( V_{in} \\) is applied to the gate of \\( M_1 \\).\n   - The source of \\( M_1 \\) is connected to ground, and the drain is connected to the output node.\n\n2. **M2 (Active Load)**:\n   - \\( M_2 \\) is configured as a current source.\n   - Its gate is connected to its drain, which ensures that \\( M_2 \\) operates in the saturation region.\n   - \\( M_2 \\) provides a high output impedance, which improves the gain of the amplifier.\n\n3. **Amplification**:\n   - When \\( V_{in} \\) increases, the gate-source voltage (\\( V_{GS1} \\)) of \\( M_1 \\) increases, causing \\( M_1 \\) to conduct more current.\n   - This increases the voltage drop across \\( M_2 \\), reducing \\( V_{out} \\).\n   - Conversely, when \\( V_{in} \\) decreases, \\( M_1 \\) conducts less current, and \\( V_{out} \\) increases.\n   - This results in an amplified, inverted output signal.\n\n---\n\n### Key Characteristics:\n1. **Voltage Gain**:\n   - The voltage gain (\\( A_v \\)) is approximately:\n     \\[\n     A_v = -g_{m1} \\cdot R_{out}\n     \\]\n     where:\n     - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n     - \\( R_{out} \\): Output resistance, primarily determined by \\( M_2 \\) in saturation.\n\n2. **High Output Impedance**:\n   - The active load \\( M_2 \\) provides a high output impedance, which enhances the voltage gain compared to a resistive load.\n\n3. **Inversion**:\n   - The circuit inverts the input signal, as the output decreases when the input increases.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog integrated circuits, such as operational amplifiers and signal processing systems, due to its high gain and compact design.",
        "format": "markdown",
        "sha256": "afcb961b4371a53825b294c995d106b54e54c7a62759bdff892c7a2a089c3aa0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly recognizes the inverting common-source behavior, but mischaracterizes the diode-connected PMOS as a high-output-impedance current-source load and gives no correct gain relation. The golden solution caps this topology misreading at 1.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 594,
        "total_tokens": 1374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 594,
        "total_tokens": 1374,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. It consists of two MOSFETs: an NMOS transistor (\\(M_1\\)) and a PMOS transistor (\\(M_2\\)). Here's the analysis:\n\n---\n\n### **Circuit Description**\n1. **PMOS Transistor (\\(M_2\\))**:\n   - Connected between \\(V_{DD}\\) (supply voltage) and the output (\\(V_{out}\\)).\n   - The gate of \\(M_2\\) is connected to the input (\\(V_{in}\\)).\n   - Conducts when \\(V_{in}\\) is low (logic 0).\n\n2. **NMOS Transistor (\\(M_1\\))**:\n   - Connected between the output (\\(V_{out}\\)) and ground.\n   - The gate of \\(M_1\\) is connected to the input (\\(V_{in}\\)).\n   - Conducts when \\(V_{in}\\) is high (logic 1).\n\n---\n\n### **Operation**\n1. **When \\(V_{in} = 0\\) (logic 0)**:\n   - \\(M_2\\) (PMOS) is ON, and \\(M_1\\) (NMOS) is OFF.\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic 1).\n\n2. **When \\(V_{in} = V_{DD}\\) (logic 1)**:\n   - \\(M_2\\) (PMOS) is OFF, and \\(M_1\\) (NMOS) is ON.\n   - The output (\\(V_{out}\\)) is pulled down to ground (logic 0).\n\n---\n\n### **Key Characteristics**\n- **Inversion**: The circuit inverts the input signal. A low input produces a high output, and a high input produces a low output.\n- **High Noise Margin**: CMOS inverters are known for their high noise margins, making them robust against noise.\n- **Low Power Consumption**: Power is consumed only during switching (when the input changes state).\n\n---\n\n### **Applications**\n- CMOS inverters are widely used in digital logic circuits, such as:\n  - Logic gates.\n  - Flip-flops.\n  - Memory cells.\n  - Microprocessors.\n\nThis circuit is a simple yet powerful example of CMOS technology in digital electronics.",
        "format": "markdown",
        "sha256": "3617c482923c6d01806ac1ddd9f65ab01b5b800f9f5cbd66586ce293cac274a1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the circuit as a CMOS inverter with an NMOS pull-down. Both devices are PMOS; M1 is a diode-connected PMOS load, so the answer misses the actual topology and gm/gm behavior.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 502,
        "total_tokens": 1282,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 502,
        "total_tokens": 1282,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. Here's an analysis of its operation:\n\n### Components:\n1. **M1**: NMOS transistor (bottom transistor).\n2. **M2**: PMOS transistor (top transistor).\n3. **\\( V_{in} \\)**: Input voltage.\n4. **\\( V_{out} \\)**: Output voltage.\n5. **\\( V_{DD} \\)**: Supply voltage.\n\n### Operation:\nThe circuit operates in two main states depending on the input voltage (\\( V_{in} \\)):\n\n#### 1. **When \\( V_{in} \\) is Low (0 or close to 0):**\n   - The NMOS transistor (M1) is OFF because \\( V_{in} \\) is less than its threshold voltage (\\( V_{th} \\)).\n   - The PMOS transistor (M2) is ON because \\( V_{in} \\) is less than \\( V_{DD} \\) (PMOS turns on when its gate voltage is low).\n   - Current flows from \\( V_{DD} \\) through M2 to the output (\\( V_{out} \\)).\n   - \\( V_{out} \\) is pulled up to \\( V_{DD} \\) (logic HIGH).\n\n#### 2. **When \\( V_{in} \\) is High (\\( V_{DD} \\)):**\n   - The NMOS transistor (M1) is ON because \\( V_{in} \\) exceeds its threshold voltage (\\( V_{th} \\)).\n   - The PMOS transistor (M2) is OFF because \\( V_{in} \\) is equal to \\( V_{DD} \\) (PMOS turns off when its gate voltage is high).\n   - Current flows from \\( V_{out} \\) through M1 to ground.\n   - \\( V_{out} \\) is pulled down to 0 (logic LOW).\n\n### Summary of Behavior:\n- **\\( V_{in} = 0 \\):** \\( V_{out} = V_{DD} \\) (logic HIGH).\n- **\\( V_{in} = V_{DD} \\):** \\( V_{out} = 0 \\) (logic LOW).\n\n### Key Characteristics:\n1. **Inversion:** The circuit inverts the input signal.\n2. **High Input Impedance:** CMOS inverters have high input impedance, meaning they draw very little current from the input source.\n3. **Low Power Consumption:** Power is consumed only during switching (when \\( V_{in} \\) transitions between 0 and \\( V_{DD} \\)).\n4. **Fast Switching:** CMOS inverters are capable of high-speed operation.\n\nThis circuit is widely used in digital logic gates, microprocessors, and other digital systems.",
        "format": "markdown",
        "sha256": "689e8681c3fb699707d80da83d7c446f2720a41943dec703f4981affb796ef47"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the circuit as a CMOS inverter with an NMOS pull-down. Both devices are PMOS; M1 is a diode-connected PMOS load, so the answer misses the circuit’s topology and gm/gm gain mechanism.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 582,
        "total_tokens": 1362,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 582,
        "total_tokens": 1362,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **CMOS inverter**, a fundamental building block in digital electronics. It consists of two MOSFETs: an NMOS transistor (\\(M_1\\)) and a PMOS transistor (\\(M_2\\)) connected in a complementary configuration. Here's the analysis:\n\n---\n\n### **Circuit Description:**\n1. **PMOS Transistor (\\(M_2\\)):**\n   - Source is connected to \\(V_{DD}\\) (positive supply voltage).\n   - Drain is connected to the output (\\(V_{out}\\)).\n   - Gate is connected to the input (\\(V_{in}\\)).\n\n2. **NMOS Transistor (\\(M_1\\)):**\n   - Source is connected to ground.\n   - Drain is connected to the output (\\(V_{out}\\)).\n   - Gate is connected to the input (\\(V_{in}\\)).\n\n---\n\n### **Operation:**\nThe circuit operates as follows, depending on the input voltage (\\(V_{in}\\)):\n\n1. **When \\(V_{in} = 0\\) (Low Input):**\n   - \\(M_1\\) (NMOS) is OFF because its gate-source voltage (\\(V_{GS}\\)) is 0.\n   - \\(M_2\\) (PMOS) is ON because its gate-source voltage (\\(V_{SG}\\)) is \\(V_{DD}\\).\n   - The output (\\(V_{out}\\)) is pulled up to \\(V_{DD}\\) (logic HIGH).\n\n2. **When \\(V_{in} = V_{DD}\\) (High Input):**\n   - \\(M_1\\) (NMOS) is ON because its gate-source voltage (\\(V_{GS}\\)) is \\(V_{DD}\\).\n   - \\(M_2\\) (PMOS) is OFF because its gate-source voltage (\\(V_{SG}\\)) is 0.\n   - The output (\\(V_{out}\\)) is pulled down to ground (logic LOW).\n\n---\n\n### **Key Characteristics:**\n1. **Inversion Property:**\n   - The circuit inverts the input signal: a LOW input produces a HIGH output, and a HIGH input produces a LOW output.\n\n2. **High Noise Margins:**\n   - The CMOS inverter has high noise margins, making it robust against noise in digital circuits.\n\n3. **Low Power Consumption:**\n   - Power is consumed only during switching (when \\(V_{in}\\) transitions between LOW and HIGH), as one transistor is always OFF in steady-state conditions.\n\n4. **Output Impedance:**\n   - The output impedance is low because either \\(M_1\\) or \\(M_2\\) provides a strong connection to ground or \\(V_{DD}\\).\n\n---\n\n### **Applications:**\n- CMOS inverters are widely used in digital logic circuits, such as microprocessors, memory, and other integrated circuits.",
        "format": "markdown",
        "sha256": "7f1218685b0ce075d7f60ab49202444b38dc94ece1180ac17a70886f848e6124"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies both the topology and M1: the circuit has two PMOS devices, with M2 as the common-source input device and M1 as a diode-connected PMOS load, not a CMOS inverter. It misses the essential gm/gm gain and operation.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 602,
        "total_tokens": 1382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 602,
        "total_tokens": 1382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To find \\( R_{\\text{out}} \\) in the given circuit, we analyze the small-signal output resistance of the cascode configuration. The circuit consists of two MOSFETs, \\( M_1 \\) and \\( M_2 \\), with \\( M_2 \\) acting as a cascode device.\n\n### Small-Signal Analysis:\n1. **Output Resistance of \\( M_1 \\):**\n   The small-signal output resistance of \\( M_1 \\) is given by:\n   \\[\n   r_{o1} = \\frac{1}{\\lambda_1 I_{D1}}\n   \\]\n   where \\( \\lambda_1 \\) is the channel-length modulation parameter of \\( M_1 \\), and \\( I_{D1} \\) is the drain current of \\( M_1 \\).\n\n2. **Output Resistance of \\( M_2 \\):**\n   The small-signal output resistance of \\( M_2 \\) is given by:\n   \\[\n   r_{o2} = \\frac{1}{\\lambda_2 I_{D2}}\n   \\]\n   where \\( \\lambda_2 \\) is the channel-length modulation parameter of \\( M_2 \\), and \\( I_{D2} \\) is the drain current of \\( M_2 \\).\n\n3. **Effective Output Resistance \\( R_{\\text{out}} \\):**\n   The cascode configuration significantly increases the output resistance due to the gain provided by \\( M_2 \\). The effective output resistance is:\n   \\[\n   R_{\\text{out}} = r_{o2} \\cdot \\left(1 + g_{m2} r_{o1}\\right)\n   \\]\n   where:\n   - \\( g_{m2} \\) is the transconductance of \\( M_2 \\),\n   - \\( r_{o1} \\) is the output resistance of \\( M_1 \\),\n   - \\( r_{o2} \\) is the output resistance of \\( M_2 \\).\n\n### Final Expression:\nSubstituting \\( r_{o1} \\) and \\( r_{o2} \\) into the equation:\n\\[\nR_{\\text{out}} = \\frac{1}{\\lambda_2 I_{D2}} \\cdot \\left(1 + g_{m2} \\cdot \\frac{1}{\\lambda_1 I_{D1}}\\right)\n\\]\n\nThis is the small-signal output resistance of the cascode circuit.",
        "format": "markdown",
        "sha256": "cd8f84e12db6609a074d8df4b8e3e979b0ac51cde1bb0a27c4186d62c00b9470"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer assigns the cascode role to M2 and uses gm2, whereas M1 is the cascode device and the leading term is gm1 ro1 ro2. It does not explicitly misidentify the devices as NMOS, so this earns limited partial credit.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 522,
        "total_tokens": 1300,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 522,
        "total_tokens": 1300,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To find \\( R_{\\text{out}} \\) in the given circuit, we analyze the small-signal output resistance of the cascode configuration. The circuit consists of two MOSFETs, \\( M_1 \\) and \\( M_2 \\), with \\( M_2 \\) acting as a cascode device.\n\n### Small-Signal Analysis:\n1. **Output Resistance of \\( M_1 \\):**\n   - The small-signal output resistance of \\( M_1 \\) is \\( r_{o1} \\), where \\( r_{o1} = \\frac{1}{\\lambda_1 I_{D1}} \\), and \\( \\lambda_1 \\) is the channel-length modulation parameter of \\( M_1 \\).\n\n2. **Effect of \\( M_2 \\):**\n   - \\( M_2 \\) increases the output resistance by providing additional gain. The small-signal resistance looking into the drain of \\( M_2 \\) is given by:\n     \\[\n     R_{\\text{out}} = r_{o2} + (1 + g_{m2} r_{o2}) r_{o1}\n     \\]\n     where:\n     - \\( r_{o2} = \\frac{1}{\\lambda_2 I_{D2}} \\) is the output resistance of \\( M_2 \\),\n     - \\( g_{m2} = \\frac{\\partial I_{D2}}{\\partial V_{GS2}} \\) is the transconductance of \\( M_2 \\).\n\n3. **Simplified Expression:**\n   - If \\( g_{m2} r_{o2} \\gg 1 \\), the output resistance simplifies to:\n     \\[\n     R_{\\text{out}} \\approx g_{m2} r_{o1} r_{o2}\n     \\]\n\n### Final Expression:\nThe output resistance \\( R_{\\text{out}} \\) of the cascode circuit is approximately:\n\\[\nR_{\\text{out}} \\approx g_{m2} r_{o1} r_{o2}\n\\]\nThis shows that the cascode configuration significantly increases the output resistance compared to a single transistor.",
        "format": "markdown",
        "sha256": "3daee77800d0e33b6eabaffbf0449bae082aeb349930336f6ad88a787661eb45"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer assigns the cascode role to M2 and uses gm2, but M1 is the cascode device, so the output resistance is approximately gm1 ro1 ro2 (with the fuller expression including ro1 + ro2).",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 453,
        "total_tokens": 1231,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 453,
        "total_tokens": 1231,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To find \\( R_{\\text{out}} \\) in the given circuit, we analyze the small-signal output resistance of the cascode configuration. The circuit consists of two MOSFETs, \\( M_1 \\) and \\( M_2 \\), with \\( M_2 \\) acting as a cascode device.\n\n### Small-Signal Analysis:\n1. **Output Resistance of \\( M_1 \\):**\n   - The small-signal output resistance of \\( M_1 \\) is \\( r_{o1} \\), where \\( r_{o1} = \\frac{1}{\\lambda_1 I_{D1}} \\).\n   - Here, \\( \\lambda_1 \\) is the channel-length modulation parameter of \\( M_1 \\), and \\( I_{D1} \\) is the drain current of \\( M_1 \\).\n\n2. **Effect of \\( M_2 \\):**\n   - \\( M_2 \\) is a cascode transistor, which increases the output resistance by providing additional gain.\n   - The small-signal resistance looking into the drain of \\( M_2 \\) is approximately:\n     \\[\n     R_{\\text{out}} = r_{o2} \\cdot (1 + g_{m2} r_{o1}),\n     \\]\n     where:\n     - \\( r_{o2} = \\frac{1}{\\lambda_2 I_{D2}} \\) is the output resistance of \\( M_2 \\),\n     - \\( g_{m2} = \\frac{\\partial I_{D2}}{\\partial V_{GS2}} \\) is the transconductance of \\( M_2 \\),\n     - \\( r_{o1} \\) is the output resistance of \\( M_1 \\).\n\n3. **Final Expression for \\( R_{\\text{out}} \\):**\n   Substituting the above terms, the total output resistance is:\n   \\[\n   R_{\\text{out}} = r_{o2} \\cdot (1 + g_{m2} r_{o1}),\n   \\]\n   where \\( r_{o2} \\) dominates the resistance, and \\( g_{m2} r_{o1} \\) provides the gain enhancement.\n\n### Key Observations:\n- The cascode configuration significantly increases the output resistance compared to a single transistor.\n- \\( R_{\\text{out}} \\) depends on the intrinsic parameters of \\( M_1 \\) and \\( M_2 \\), such as \\( g_{m2} \\), \\( r_{o1} \\), and \\( r_{o2} \\).",
        "format": "markdown",
        "sha256": "685f0870571e1201e4331d9311eba4930f18dcc11a928a293e25dae7d468c012"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer incorrectly identifies M2 as the cascode device and uses gm2; the actual cascode device is M1, so the output-resistance expression is wrong. It only earns limited credit for recognizing cascode resistance enhancement.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 544,
        "total_tokens": 1322,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 778,
        "output_tokens": 544,
        "total_tokens": 1322,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To ensure that transistor \\( M_2 \\) is in saturation in the given circuit, the following condition must be satisfied:\n\n\\[\nV_{DS2} \\geq V_{GS2} - V_{th2}\n\\]\n\nWhere:\n- \\( V_{DS2} \\) is the drain-to-source voltage of \\( M_2 \\),\n- \\( V_{GS2} \\) is the gate-to-source voltage of \\( M_2 \\),\n- \\( V_{th2} \\) is the threshold voltage of \\( M_2 \\).\n\n### Steps to Ensure \\( M_2 \\) is in Saturation:\n1. **Determine \\( V_{GS2} \\):**\n   - The gate of \\( M_2 \\) is connected to \\( V_{b2} \\), and the source of \\( M_2 \\) is at node \\( X \\). Thus:\n     \\[\n     V_{GS2} = V_{b2} - V_X\n     \\]\n\n2. **Determine \\( V_{DS2} \\):**\n   - The drain of \\( M_2 \\) is connected to \\( V_{DD} \\), and the source is at \\( V_X \\). Thus:\n     \\[\n     V_{DS2} = V_{DD} - V_X\n     \\]\n\n3. **Saturation Condition:**\n   - Substitute \\( V_{GS2} \\) and \\( V_{DS2} \\) into the saturation condition:\n     \\[\n     V_{DD} - V_X \\geq (V_{b2} - V_X) - V_{th2}\n     \\]\n\n4. **Simplify the Inequality:**\n   - Rearrange the terms:\n     \\[\n     V_{DD} \\geq V_{b2} - V_{th2}\n     \\]\n\n### Key Design Considerations:\n- Ensure that \\( V_{b2} \\) is chosen such that \\( V_{DD} \\) satisfies the above inequality.\n- \\( V_X \\) is determined by the operation of \\( M_1 \\), so \\( M_1 \\) must also be properly biased to ensure \\( M_2 \\) remains in saturation.\n\nBy carefully selecting \\( V_{b2} \\) and ensuring \\( V_{DD} \\) is sufficiently high, \\( M_2 \\) can be kept in saturation.",
        "format": "markdown",
        "sha256": "74d916ac7047c66dd074484e06fddd49422ff8c5d0de6f92d734bcfe7712a2bd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It uses the NMOS saturation condition and reverses M2’s source and drain; the resulting inequality misses the essential relation between VX and Vb1. It earns minimal credit for mentioning saturation and that M1 affects VX.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 491,
        "total_tokens": 1277,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 491,
        "total_tokens": 1277,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To ensure that transistor \\( M_2 \\) is in saturation in the given circuit, the following condition must be satisfied:\n\n\\[\nV_{DS2} \\geq V_{GS2} - V_{th2}\n\\]\n\nWhere:\n- \\( V_{DS2} \\) is the drain-to-source voltage of \\( M_2 \\),\n- \\( V_{GS2} \\) is the gate-to-source voltage of \\( M_2 \\),\n- \\( V_{th2} \\) is the threshold voltage of \\( M_2 \\).\n\n### Steps to Ensure \\( M_2 \\) is in Saturation:\n1. **Determine \\( V_{GS2} \\):**\n   - The gate of \\( M_2 \\) is connected to \\( V_{b2} \\), and the source of \\( M_2 \\) is at node \\( X \\). Thus:\n     \\[\n     V_{GS2} = V_{b2} - V_X\n     \\]\n\n2. **Determine \\( V_{DS2} \\):**\n   - The drain of \\( M_2 \\) is connected to \\( V_{DD} \\), and the source is at node \\( X \\). Thus:\n     \\[\n     V_{DS2} = V_{DD} - V_X\n     \\]\n\n3. **Saturation Condition:**\n   - Substitute \\( V_{GS2} \\) and \\( V_{DS2} \\) into the saturation condition:\n     \\[\n     V_{DD} - V_X \\geq (V_{b2} - V_X) - V_{th2}\n     \\]\n\n4. **Simplify the Inequality:**\n   - Rearrange the terms:\n     \\[\n     V_{DD} \\geq V_{b2} - V_{th2}\n     \\]\n\n### Key Design Considerations:\n- Ensure that \\( V_{b2} \\) is chosen such that \\( V_{DD} \\geq V_{b2} - V_{th2} \\).\n- \\( V_X \\) is determined by the operation of \\( M_1 \\), so ensure that \\( M_1 \\) is also properly biased to maintain \\( V_X \\) at a level that satisfies the above condition.\n\nBy carefully selecting \\( V_{b2} \\) and ensuring \\( V_{DD} \\) is sufficiently high, \\( M_2 \\) can be kept in saturation.",
        "format": "markdown",
        "sha256": "82341a106ff7fb781736d68002947f8023de7d24238310f806e836bbc5722661"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It reverses M2’s source and drain and applies the NMOS saturation condition to the PMOS device, yielding an irrelevant condition on VDD and Vb2. It does not relate VX to Vb1 as required.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 505,
        "total_tokens": 1291,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 505,
        "total_tokens": 1291,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To ensure that transistor **M2** is in saturation in the given circuit, the following condition must be satisfied:\n\n\\[\nV_{DS2} \\geq V_{GS2} - V_{th2}\n\\]\n\nWhere:\n- \\( V_{DS2} \\) is the drain-to-source voltage of \\( M_2 \\),\n- \\( V_{GS2} \\) is the gate-to-source voltage of \\( M_2 \\),\n- \\( V_{th2} \\) is the threshold voltage of \\( M_2 \\).\n\n### Steps to Ensure \\( M_2 \\) is in Saturation:\n1. **Gate Voltage of \\( M_2 \\):**\n   The gate voltage of \\( M_2 \\) is set by \\( V_{b2} \\). Ensure that \\( V_{b2} \\) is high enough to turn \\( M_2 \\) on and allow it to operate in saturation.\n\n2. **Source Voltage of \\( M_2 \\):**\n   The source of \\( M_2 \\) is connected to the drain of \\( M_1 \\) (node \\( X \\)). The voltage at node \\( X \\) depends on the current through \\( M_1 \\) and the biasing conditions of \\( M_1 \\). Ensure that the voltage at \\( X \\) is low enough to satisfy the saturation condition for \\( M_2 \\).\n\n3. **Drain Voltage of \\( M_2 \\):**\n   The drain of \\( M_2 \\) is connected to \\( V_{DD} \\), which is typically the highest voltage in the circuit. This ensures that \\( V_{DS2} \\) is large enough to meet the saturation condition.\n\n4. **Verify \\( V_{DS2} \\):**\n   Calculate \\( V_{DS2} = V_{DD} - V_X \\), where \\( V_X \\) is the voltage at node \\( X \\). Ensure that:\n   \\[\n   V_{DD} - V_X \\geq V_{b2} - V_X - V_{th2}\n   \\]\n   Simplifying:\n   \\[\n   V_{DD} \\geq V_{b2} - V_{th2}\n   \\]\n\n### Design Considerations:\n- Choose \\( V_{b2} \\) such that \\( M_2 \\) is properly biased in saturation.\n- Ensure that \\( M_1 \\) is also in saturation, as its operation affects the voltage at node \\( X \\).\n- Verify that \\( V_{DD} \\) is sufficiently high to maintain \\( M_2 \\) in saturation.\n\nBy carefully setting \\( V_{b2} \\), \\( V_{b1} \\), and \\( V_{DD} \\), you can ensure that \\( M_2 \\) operates in the saturation region.",
        "format": "markdown",
        "sha256": "ed5d8e2a7fafd1f907f80c12ef028a4835ff440e946b3a04dac025877357805f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It gives a generic saturation criterion and mentions node X, but reverses M2’s PMOS terminal orientation, uses the NMOS condition, and incorrectly treats Vb2 as the control. It misses the key relation between X and Vb1.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 582,
        "total_tokens": 1368,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 786,
        "output_tokens": 582,
        "total_tokens": 1368,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current source load**. Here's a detailed analysis:\n\n---\n\n### Components and Configuration:\n1. **Transistors:**\n   - \\( M_1 \\): Acts as the input transistor, configured in a common-source configuration.\n   - \\( M_2 \\): Acts as a current source, providing a constant current \\( I_1 \\) to the circuit.\n\n2. **Biasing:**\n   - \\( V_{b1} \\): Provides the gate bias voltage for \\( M_2 \\), ensuring it operates in the saturation region as a current source.\n   - \\( V_{in} \\): The input signal applied to the gate of \\( M_1 \\).\n\n3. **Current Source:**\n   - The current source \\( I_1 \\) ensures a constant current flows through \\( M_2 \\), which is mirrored to \\( M_1 \\).\n\n4. **Output:**\n   - \\( V_{out} \\): The output voltage is taken at the drain of \\( M_2 \\).\n\n---\n\n### Operation:\n1. **Input Stage:**\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M_1 \\), causing variations in its drain current \\( I_{D1} \\).\n   - \\( M_1 \\) operates in the saturation region, where its drain current is approximately:\n     \\[\n     I_{D1} = \\frac{1}{2} k_n (V_{GS1} - V_{th})^2\n     \\]\n     where \\( k_n \\) is the transconductance parameter, \\( V_{GS1} = V_{in} - V_{SS} \\), and \\( V_{th} \\) is the threshold voltage.\n\n2. **Current Source Load:**\n   - \\( M_2 \\) is biased to operate as a current source, providing a constant current \\( I_1 \\). This ensures that the current through \\( M_1 \\) is mirrored to \\( M_2 \\).\n\n3. **Output Voltage:**\n   - The output voltage \\( V_{out} \\) is determined by the voltage drop across \\( M_2 \\):\n     \\[\n     V_{out} = V_{DD} - I_{D2} R_{out}\n     \\]\n     where \\( R_{out} \\) is the output resistance of \\( M_2 \\).\n\n4. **Small-Signal Gain:**\n   - The small-signal voltage gain \\( A_v \\) of the circuit is given by:\n     \\[\n     A_v = -g_{m1} R_{out}\n     \\]\n     where \\( g_{m1} \\) is the transconductance of \\( M_1 \\), and \\( R_{out} \\) is the output resistance of \\( M_2 \\).\n\n---\n\n### Key Observations:\n1. **High Gain:**\n   - The circuit achieves high gain due to the high output resistance of the current source load (\\( M_2 \\)).\n\n2. **Linear Amplification:**\n   - The circuit amplifies small input signals linearly, provided \\( M_1 \\) and \\( M_2 \\) remain in the saturation region.\n\n3. **Biasing Stability:**\n   - Proper biasing of \\( M_2 \\) (via \\( V_{b1} \\)) ensures a stable operating point for the circuit.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing, such as in operational amplifiers, voltage amplifiers, and active loads.",
        "format": "markdown",
        "sha256": "f89ba7f71c4aea3bbbdb8ebd800c6e059802670c328b60f3718bf909e70bdb97"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M2 as a current-source load rather than the NMOS common-gate cascode and assigns the load role incorrectly. Although it gives a generic common-source gain formula, it misses the circuit’s defining topology and boosted output resistance.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 739,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 739,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current source load**. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **Transistor \\( M_1 \\):**\n   - Acts as the input transistor.\n   - Its gate is driven by the input signal \\( V_{in} \\).\n   - Operates in the saturation region for amplification.\n\n2. **Transistor \\( M_2 \\):**\n   - Acts as a current source load.\n   - Its gate is biased by \\( V_{b1} \\), which sets the current through \\( M_2 \\).\n\n3. **Current Source \\( I_1 \\):**\n   - Provides a constant current \\( I_1 \\) to the circuit.\n   - Ensures that \\( M_2 \\) operates in the saturation region.\n\n4. **Output Node \\( V_{out} \\):**\n   - The output voltage is taken at the drain of \\( M_2 \\).\n\n---\n\n### **Operation**\n1. **Input Signal:**\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M_1 \\), causing variations in its drain current.\n\n2. **Current Flow:**\n   - The current through \\( M_1 \\) flows through \\( M_2 \\), which acts as a load.\n   - \\( M_2 \\) is biased to operate in the saturation region, providing a high output impedance.\n\n3. **Output Voltage:**\n   - The output voltage \\( V_{out} \\) is determined by the voltage drop across \\( M_2 \\).\n   - As \\( V_{in} \\) increases, the current through \\( M_1 \\) increases, causing \\( V_{out} \\) to decrease.\n\n---\n\n### **Key Equations**\n1. **Current through \\( M_1 \\):**\n   \\[\n   I_{D1} = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{GS1} - V_{th})^2\n   \\]\n   where \\( V_{GS1} = V_{in} \\).\n\n2. **Output Voltage:**\n   \\[\n   V_{out} = V_{DD} - I_{D1} R_{out}\n   \\]\n   where \\( R_{out} \\) is the output resistance of \\( M_2 \\).\n\n3. **Small-Signal Gain:**\n   \\[\n   A_v = -g_{m1} R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\) is the transconductance of \\( M_1 \\).\n   - \\( R_{out} \\) is the output resistance of \\( M_2 \\).\n\n---\n\n### **Design Considerations**\n1. **Biasing:**\n   - \\( V_{b1} \\) must be chosen to ensure \\( M_2 \\) operates in saturation.\n   - \\( V_{in} \\) must be within a range to keep \\( M_1 \\) in saturation.\n\n2. **Gain:**\n   - The gain depends on \\( g_{m1} \\) and \\( R_{out} \\).\n   - \\( g_{m1} \\) can be increased by increasing the width-to-length ratio \\( W/L \\) of \\( M_1 \\).\n\n3. **Output Impedance:**\n   - The high output impedance of \\( M_2 \\) improves the gain.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing as a high-gain amplifier.\n- It is also a building block in operational amplifiers and other analog integrated circuits.",
        "format": "markdown",
        "sha256": "47b1b75bccf4bfd95012c53a8eeb5dd5c603078661ed204198123f346c6404c7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M1 as the input device, predicts an inverted response, and gives a generic common-source gain form. But it misidentifies M2 as a current-source load rather than the NMOS common-gate cascode, and therefore misses the cascode’s role in boosting output resistance; its stated gain also treats Rout as belonging to M2 alone.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 757,
        "total_tokens": 1537,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 757,
        "total_tokens": 1537,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current source load**. Here's a detailed analysis:\n\n---\n\n### Components and Configuration:\n1. **Transistors:**\n   - \\( M_1 \\): Acts as the input transistor, configured in a common-source configuration.\n   - \\( M_2 \\): Acts as a current source load, with its gate biased by \\( V_{b1} \\).\n\n2. **Current Source:**\n   - \\( I_1 \\): Provides a constant current to the circuit.\n\n3. **Biasing:**\n   - \\( V_{b1} \\): Sets the gate voltage of \\( M_2 \\), ensuring it operates in saturation as a current source.\n\n4. **Input and Output:**\n   - \\( V_{in} \\): The input signal applied to the gate of \\( M_1 \\).\n   - \\( V_{out} \\): The output voltage, taken at the drain of \\( M_1 \\).\n\n---\n\n### Operation:\n1. **DC Biasing:**\n   - \\( M_2 \\) is biased to operate in saturation, acting as a high-impedance current source.\n   - \\( M_1 \\) is also biased to operate in saturation, with its gate voltage determined by \\( V_{in} \\).\n\n2. **Small-Signal Analysis:**\n   - The small-signal input \\( v_{in} \\) modulates the gate voltage of \\( M_1 \\), causing a change in its drain current.\n   - The drain current of \\( M_1 \\) flows through \\( M_2 \\), which acts as a load.\n   - The output voltage \\( v_{out} \\) is given by:\n     \\[\n     v_{out} = -g_{m1} v_{in} R_{out}\n     \\]\n     where:\n     - \\( g_{m1} \\): Transconductance of \\( M_1 \\).\n     - \\( R_{out} \\): Output resistance of the circuit, dominated by the output resistance of \\( M_2 \\) (\\( r_{o2} \\)).\n\n3. **Voltage Gain:**\n   - The voltage gain \\( A_v \\) is approximately:\n     \\[\n     A_v = -g_{m1} r_{o2}\n     \\]\n     where \\( r_{o2} \\) is the output resistance of \\( M_2 \\).\n\n4. **High Impedance Load:**\n   - The current source \\( M_2 \\) provides a high output impedance, improving the gain of the amplifier.\n\n---\n\n### Key Observations:\n1. **High Gain:**\n   - The circuit achieves high gain due to the high output resistance of \\( M_2 \\).\n\n2. **Current Source Load:**\n   - The use of \\( M_2 \\) as a current source load improves linearity and gain compared to a resistive load.\n\n3. **Frequency Response:**\n   - The circuit's frequency response is determined by the parasitic capacitances of \\( M_1 \\) and \\( M_2 \\), as well as the load capacitance.\n\n---\n\n### Applications:\nThis circuit is commonly used in analog integrated circuits as a high-gain amplifier stage, particularly in operational amplifiers and other high-performance analog designs.",
        "format": "markdown",
        "sha256": "376d6d564c376a8b0effaecd38a3b748eeec37ecdd849faf45475614efd4afa8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M2 as a current-source load and places the output at M1’s drain. M2 is the NMOS common-gate cascode, and its stack boosts the output resistance; the stated gain using only M2’s ro is therefore incorrect.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 676,
        "total_tokens": 1456,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 676,
        "total_tokens": 1456,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**. \n\nIn this circuit:\n- **M1** is the input transistor, which is typically configured as a common-source amplifier.\n- **M2** is the cascode transistor, which is biased by the voltage \\( V_{b1} \\). It is configured to improve the gain and bandwidth of the circuit by reducing the Miller effect and increasing the output impedance.\n\nThis arrangement is a classic cascode configuration, commonly used in analog circuit design to enhance performance.",
        "format": "markdown",
        "sha256": "2c28a6d76b052c4ae3969dcd52efbef36835f4237b1f628d970d81f8a9860add"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower, not a common-source input stage, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 108,
        "total_tokens": 892,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 108,
        "total_tokens": 892,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**. \n\nIn this circuit:\n- **M1** is the input transistor, which amplifies the input signal \\( V_{in} \\).\n- **M2** is the cascode transistor, which is biased by \\( V_{b1} \\). It improves the performance of the circuit by increasing the output impedance and reducing the Miller effect, leading to better frequency response and gain stability.\n\nThis configuration is a classic example of a cascode amplifier.",
        "format": "markdown",
        "sha256": "178eadc656c069d1c7bc1836e519d803e2270006eaca3a5f2fa93f9505be4fd9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Incorrectly calls the circuit a cascode. M1 is a PMOS source follower, not a common-source input stage, so the structure lacks cascode output-resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 106,
        "total_tokens": 890,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 106,
        "total_tokens": 890,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**. \n\nIn this circuit:\n- **M1** is the input transistor, which amplifies the input signal \\( V_{in} \\).\n- **M2** is the cascode transistor, which is biased by \\( V_{b1} \\). It improves the performance of the circuit by increasing the output impedance and reducing the Miller effect, leading to better frequency response and gain stability.\n\nThis configuration is a classic example of a cascode amplifier.",
        "format": "markdown",
        "sha256": "178eadc656c069d1c7bc1836e519d803e2270006eaca3a5f2fa93f9505be4fd9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Incorrectly calls the circuit a cascode. M1 is a PMOS source follower, not a common-source input stage, so the structure lacks cascode output-resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 106,
        "total_tokens": 890,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 106,
        "total_tokens": 890,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The Miller effect is less pronounced in a cascode amplifier due to the specific configuration of the circuit, which minimizes the voltage gain across the input-output capacitance of the amplifying transistor.\n\n### Understanding the Miller Effect:\nThe Miller effect occurs when a capacitance (e.g., the parasitic capacitance between the input and output of a transistor, \\(C_{gd}\\)) is multiplied by the gain of the stage, effectively increasing the input capacitance seen by the circuit. This can significantly degrade the high-frequency performance of the amplifier.\n\n### Cascode Configuration:\nIn a cascode amplifier, a common-emitter (or common-source) stage is cascaded with a common-base (or common-gate) stage. The key feature of the cascode is that the output voltage of the first transistor (common-emitter/source) is held relatively constant by the low input impedance of the second transistor (common-base/gate). This has the following effects:\n\n1. **Reduced Voltage Gain Across \\(C_{gd}\\):**\n   The Miller effect depends on the voltage gain between the input and output of the transistor. In the cascode configuration, the voltage at the collector (or drain) of the first transistor is relatively constant because it is connected to the low-impedance input of the second transistor. As a result, the voltage gain across \\(C_{gd}\\) of the first transistor is very small, and the effective Miller capacitance is greatly reduced.\n\n2. **Isolation of \\(C_{gd}\\):**\n   The second transistor in the cascode acts as a buffer, isolating the high-frequency effects of \\(C_{gd}\\) from the input. This further reduces the impact of the Miller effect on the overall circuit performance.\n\n3. **Improved High-Frequency Response:**\n   With the Miller effect suppressed, the input capacitance of the cascode amplifier is much smaller compared to a single-stage amplifier. This allows the cascode to achieve better high-frequency performance and a wider bandwidth.\n\n### Summary:\nThe Miller effect is less pronounced in a cascode amplifier because the voltage gain across the input-output capacitance (\\(C_{gd}\\)) of the first transistor is minimized due to the low impedance at the input of the second transistor. This reduces the effective Miller capacitance and improves the high-frequency performance of the circuit.",
        "format": "markdown",
        "sha256": "7c4877e8ad723c4b7ed5dcafe4d496e5bcbafa07f9856b3f4fe5795a7575e82b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the low-impedance cascode node as reducing the gain across the input transistor’s Cgd. However, it overstates the reduction by calling that gain very small and the drain relatively constant; it is roughly −1 for similar devices, so the Miller effect is reduced, not nearly eliminated.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 469,
        "total_tokens": 489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 469,
        "total_tokens": 489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The Miller effect is less pronounced in a cascode amplifier due to the specific configuration of the circuit, which minimizes the voltage gain across the input-output capacitance of the amplifying transistor.\n\n### Understanding the Miller Effect:\nThe Miller effect occurs when a capacitance (e.g., the parasitic capacitance between the input and output of a transistor, \\(C_{gd}\\)) is multiplied by the gain of the stage, effectively increasing the equivalent input capacitance. This can significantly degrade the high-frequency performance of the circuit.\n\n### Cascode Configuration:\nIn a cascode amplifier, a common-emitter (or common-source) stage is cascaded with a common-base (or common-gate) stage. The key feature of the cascode is that the output voltage of the first transistor (common-emitter/source) is held relatively constant by the low input impedance of the second transistor (common-base/gate). This has the following effects:\n\n1. **Reduced Voltage Gain Across \\(C_{gd}\\):**\n   The Miller effect depends on the voltage gain between the input and output of the transistor. In the cascode configuration, the voltage at the collector (or drain) of the first transistor is relatively constant because it is connected to the low-impedance input of the second transistor. As a result, the effective gain across \\(C_{gd}\\) is very small, and the Miller multiplication of \\(C_{gd}\\) is minimized.\n\n2. **Isolation of Input and Output:**\n   The cascode configuration effectively isolates the input and output stages. The first transistor handles the voltage gain, while the second transistor provides a high output impedance and prevents the output signal from feeding back to the input. This isolation further reduces the impact of the Miller effect.\n\n3. **Improved High-Frequency Performance:**\n   By minimizing the Miller effect, the cascode amplifier reduces the equivalent input capacitance and increases the bandwidth of the circuit. This makes the cascode configuration particularly suitable for high-frequency applications.\n\n### Summary:\nThe Miller effect is less pronounced in a cascode amplifier because the voltage gain across the input-output capacitance (\\(C_{gd}\\)) of the first transistor is greatly reduced due to the low impedance at the input of the second transistor. This minimizes the effective input capacitance and improves the high-frequency performance of the circuit.",
        "format": "markdown",
        "sha256": "7d12017d44857cd60982981c714b7763463015eea5713431689a4fa7886870ec"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the low-impedance cascode node as reducing the gain across Cgd, but overstates the reduction by calling that gain very small. It is roughly -1 for similar devices, so the Miller effect is reduced, not nearly eliminated.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 469,
        "total_tokens": 489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 469,
        "total_tokens": 489,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The Miller effect is less pronounced in a cascode amplifier due to the specific configuration of the circuit, which minimizes the voltage gain across the input-output capacitance of the amplifying transistor.\n\n### Understanding the Miller Effect:\nThe Miller effect occurs when a capacitance (e.g., the parasitic capacitance between the input and output of a transistor, \\(C_{gd}\\)) is multiplied by the gain of the stage, effectively increasing the equivalent input capacitance. This can significantly degrade the high-frequency performance of the circuit.\n\n### Cascode Configuration:\nIn a cascode amplifier, a common-emitter (or common-source) stage is cascaded with a common-base (or common-gate) stage. The key feature of the cascode is that the output voltage of the first transistor (common-emitter/source) is held relatively constant by the low input impedance of the second transistor (common-base/gate). This has the following effects:\n\n1. **Reduced Voltage Gain Across \\(C_{gd}\\):**\n   The Miller effect depends on the voltage gain between the input and output of the transistor. In the cascode configuration, the voltage at the collector (or drain) of the first transistor is relatively constant because it is connected to the low-impedance input of the second transistor. As a result, the voltage gain across \\(C_{gd}\\) of the first transistor is very small, and the Miller multiplication effect is minimized.\n\n2. **Isolation of Input and Output:**\n   The cascode configuration effectively isolates the input and output stages. The second transistor (common-base/gate) prevents the output signal from feeding back to the input, further reducing the impact of \\(C_{gd}\\).\n\n3. **Improved High-Frequency Performance:**\n   By suppressing the Miller effect, the cascode amplifier exhibits a much smaller equivalent input capacitance. This allows the circuit to maintain higher bandwidth and better high-frequency performance compared to a single-stage amplifier.\n\n### Summary:\nThe Miller effect is less pronounced in a cascode amplifier because the voltage gain across the parasitic capacitance \\(C_{gd}\\) of the first transistor is minimized due to the low impedance at the input of the second transistor. This reduces the effective input capacitance and improves the high-frequency performance of the circuit.",
        "format": "markdown",
        "sha256": "d8a679923a3a91738d20235a80870e73e8d699379a8bbad4acd75ba0fda0f3a8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance node at the first transistor’s drain as reducing the swing across its Cgd and hence Miller multiplication. It somewhat overstates the reduction by calling the gain very small, but the golden solution treats that as a minor flaw.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 459,
        "total_tokens": 479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 20,
        "output_tokens": 459,
        "total_tokens": 479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**, commonly used in analog design. Here's a detailed analysis:\n\n### Components:\n1. **M1**: A PMOS transistor acting as an active load.\n2. **M2**: An NMOS transistor configured as the amplifying device.\n3. **\\( V_{b1} \\)**: Bias voltage for the NMOS transistor \\( M2 \\).\n4. **\\( V_{b2} \\)**: Bias voltage for the PMOS transistor \\( M1 \\).\n5. **\\( V_{DD} \\)**: Supply voltage.\n6. **\\( V_{in} \\)**: Input signal applied to the gate of \\( M2 \\).\n7. **\\( V_{out} \\)**: Output voltage.\n\n---\n\n### Operation:\n1. **Biasing**:\n   - \\( M1 \\) is biased in the saturation region by \\( V_{b2} \\), acting as a current source.\n   - \\( M2 \\) is biased in the saturation region by \\( V_{b1} \\), allowing it to amplify the input signal.\n\n2. **Amplification**:\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M2 \\), causing variations in its drain current.\n   - The drain current of \\( M2 \\) flows through \\( M1 \\), which acts as a load. The output voltage \\( V_{out} \\) is taken at the drain of \\( M2 \\).\n\n3. **Voltage Gain**:\n   - The small-signal voltage gain \\( A_v \\) is approximately:\n     \\[\n     A_v = -g_{m2} \\cdot r_{o1} \\parallel r_{o2}\n     \\]\n     where:\n     - \\( g_{m2} \\): Transconductance of \\( M2 \\).\n     - \\( r_{o1} \\): Output resistance of \\( M1 \\).\n     - \\( r_{o2} \\): Output resistance of \\( M2 \\).\n     - \\( r_{o1} \\parallel r_{o2} \\): Parallel combination of the output resistances of \\( M1 \\) and \\( M2 \\).\n\n4. **Output Impedance**:\n   - The output impedance is dominated by the parallel combination of \\( r_{o1} \\) and \\( r_{o2} \\).\n\n---\n\n### Key Features:\n- **High Gain**: The active load (PMOS \\( M1 \\)) increases the output resistance, enhancing the voltage gain.\n- **Small Signal Amplification**: The circuit amplifies small variations in \\( V_{in} \\).\n- **Biasing Stability**: Proper biasing of \\( M1 \\) and \\( M2 \\) ensures both transistors operate in the saturation region.\n\n---\n\n### Applications:\n- Used in analog circuits such as operational amplifiers, differential amplifiers, and other signal processing blocks where high gain is required.",
        "format": "markdown",
        "sha256": "a64ca2f5c2e25636ff9593d4019a90de46e76716dde6c7c3716affd22315e1f4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at the gate of M2 and identifies the stage as common-source, contradicting the essential common-gate topology; the gain polarity is also wrong.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 612,
        "total_tokens": 1392,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 612,
        "total_tokens": 1392,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**, commonly used in analog design. Here's a detailed analysis:\n\n---\n\n### **Components and Configuration**\n1. **Transistor \\( M_1 \\):**\n   - Acts as an active load.\n   - Its gate is biased with \\( V_{b2} \\), which sets its operating point.\n\n2. **Transistor \\( M_2 \\):**\n   - Acts as the amplifying transistor.\n   - Its gate is connected to the input signal \\( V_{in} \\).\n   - Its source is biased with \\( V_{b1} \\), which sets the current through \\( M_2 \\).\n\n3. **Power Supply \\( V_{DD} \\):**\n   - Provides the supply voltage for the circuit.\n\n4. **Output \\( V_{out} \\):**\n   - Taken at the drain of \\( M_2 \\), which is also the drain of \\( M_1 \\).\n\n---\n\n### **Operation**\n1. **Biasing:**\n   - \\( V_{b1} \\) sets the bias current through \\( M_2 \\).\n   - \\( V_{b2} \\) sets the operating point of \\( M_1 \\), ensuring it operates in the saturation region to act as a high-impedance load.\n\n2. **Amplification:**\n   - When \\( V_{in} \\) increases, the gate-source voltage \\( V_{gs2} \\) of \\( M_2 \\) increases, causing an increase in the drain current \\( I_{D2} \\).\n   - This increase in \\( I_{D2} \\) causes a voltage drop across \\( M_1 \\), reducing \\( V_{out} \\).\n   - Conversely, when \\( V_{in} \\) decreases, \\( I_{D2} \\) decreases, and \\( V_{out} \\) increases.\n   - This results in an inverted output signal.\n\n3. **Active Load:**\n   - \\( M_1 \\) operates in saturation and provides a high output impedance, which increases the voltage gain of the circuit.\n\n---\n\n### **Key Equations**\n1. **Voltage Gain (\\( A_v \\)):**\n   \\[\n   A_v = -g_{m2} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m2} \\) is the transconductance of \\( M_2 \\).\n   - \\( R_{out} \\) is the output resistance, primarily determined by \\( M_1 \\) in saturation.\n\n2. **Output Resistance (\\( R_{out} \\)):**\n   \\[\n   R_{out} \\approx r_{o1} \\parallel r_{o2}\n   \\]\n   where:\n   - \\( r_{o1} \\) is the output resistance of \\( M_1 \\).\n   - \\( r_{o2} \\) is the output resistance of \\( M_2 \\).\n\n3. **Bias Current (\\( I_{D2} \\)):**\n   \\[\n   I_{D2} = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{gs2} - V_{th})^2\n   \\]\n   where:\n   - \\( \\mu_n \\) is the mobility of electrons.\n   - \\( C_{ox} \\) is the oxide capacitance per unit area.\n   - \\( W/L \\) is the width-to-length ratio of \\( M_2 \\).\n   - \\( V_{th} \\) is the threshold voltage of \\( M_2 \\).\n\n---\n\n### **Design Considerations**\n1. **Bias Voltages (\\( V_{b1} \\) and \\( V_{b2} \\)):**\n   - Must be chosen to ensure both \\( M_1 \\) and \\( M_2 \\) operate in the saturation region.\n\n2. **Gain:**\n   - The gain depends on \\( g_{m2} \\) and \\( R_{out} \\). Increasing \\( g_{m2} \\) (by increasing \\( I_{D2} \\)) or \\( R_{out} \\) (by ensuring \\( M_1 \\) has a high output resistance) improves the gain.\n\n3. **Linearity:**\n   - The circuit is nonlinear for large input signals. To maintain linearity, \\( V_{in} \\) should be small enough to keep \\( M_2 \\) in saturation.\n\n---\n\n### **Applications**\n- This circuit is commonly used in:\n  - Analog signal amplification.\n  - Differential amplifiers (as part of a larger circuit).\n  - Low-noise amplifiers.",
        "format": "markdown",
        "sha256": "50122fcf92d85587f562a833d07ca0ac2f1ccb12f2692927dc64c7ef698e692f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2’s gate and identifies the circuit as common-source, contradicting the essential topology: it is a common-gate stage with Vin at M2’s source. Its gain polarity and operation are therefore also incorrect.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 965,
        "total_tokens": 1745,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 965,
        "total_tokens": 1745,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**, commonly used in analog design. Here's a detailed analysis:\n\n---\n\n### Components:\n1. **M1**: A PMOS transistor acting as an active load.\n2. **M2**: An NMOS transistor configured as the main amplifying device.\n3. **\\( V_{b1} \\)**: Bias voltage for M2 to set its operating point.\n4. **\\( V_{b2} \\)**: Bias voltage for M1 to control its current.\n5. **\\( V_{in} \\)**: Input signal applied to the gate of M2.\n6. **\\( V_{out} \\)**: Output voltage taken from the drain of M2.\n\n---\n\n### Operation:\n1. **Biasing**:\n   - \\( V_{b1} \\) sets the gate voltage of M2, ensuring it operates in the saturation region.\n   - \\( V_{b2} \\) sets the gate voltage of M1, ensuring it also operates in the saturation region.\n\n2. **Amplification**:\n   - When \\( V_{in} \\) increases, the gate-to-source voltage (\\( V_{gs} \\)) of M2 increases, causing an increase in its drain current (\\( I_{D2} \\)).\n   - The increase in \\( I_{D2} \\) causes a larger voltage drop across M1, reducing \\( V_{out} \\).\n   - Conversely, when \\( V_{in} \\) decreases, \\( I_{D2} \\) decreases, reducing the voltage drop across M1 and increasing \\( V_{out} \\).\n\n3. **Active Load**:\n   - M1 acts as an active load, providing a high output impedance. This increases the voltage gain of the circuit compared to a resistive load.\n\n---\n\n### Key Equations:\n1. **Voltage Gain**:\n   \\[\n   A_v = -g_{m2} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m2} \\): Transconductance of M2.\n   - \\( R_{out} \\): Output resistance, primarily determined by the parallel combination of the output resistances of M1 and M2.\n\n2. **Output Resistance**:\n   \\[\n   R_{out} = r_{o1} \\parallel r_{o2}\n   \\]\n   where:\n   - \\( r_{o1} \\): Output resistance of M1.\n   - \\( r_{o2} \\): Output resistance of M2.\n\n3. **Bias Current**:\n   The bias current through M1 and M2 is determined by \\( V_{b1} \\) and \\( V_{b2} \\).\n\n---\n\n### Design Considerations:\n1. **Biasing**:\n   Proper selection of \\( V_{b1} \\) and \\( V_{b2} \\) ensures both transistors operate in the saturation region for linear amplification.\n\n2. **Gain**:\n   The gain depends on \\( g_{m2} \\) and \\( R_{out} \\). Increasing \\( g_{m2} \\) (by increasing the bias current) or \\( R_{out} \\) (by increasing the channel length of M1 and M2) improves the gain.\n\n3. **Frequency Response**:\n   The circuit's bandwidth is limited by the parasitic capacitances at the output node and the transistors.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing, such as in operational amplifiers, mixers, and other analog front-end circuits.",
        "format": "markdown",
        "sha256": "632b1e6d304b0e769ad3e0225867b6d8cdde9a7c9726b46f6c4abc4790548e39"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at M2’s gate and identifies the circuit as a common-source amplifier, contradicting the common-gate topology. Its inverted-gain analysis is therefore wrong; the golden solution explicitly assigns 0 for this error.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 739,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 739,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the number of poles in the circuit, we analyze the capacitors and their associated nodes. Each capacitor introduces a pole in the frequency response of the circuit. \n\n### Capacitors in the circuit:\n1. **\\( C_{GS} \\):** Gate-to-source capacitance of \\( M_1 \\).\n2. **\\( C_{GD} \\):** Gate-to-drain capacitance of \\( M_1 \\).\n3. **\\( C_{DB} \\):** Drain-to-bulk capacitance of \\( M_1 \\).\n4. **\\( C_{GD2} \\):** Gate-to-drain capacitance of \\( M_2 \\).\n5. **\\( C_{DB2} \\):** Drain-to-bulk capacitance of \\( M_2 \\).\n\n### Total number of poles:\nEach of these capacitors contributes a pole to the circuit. Therefore, the circuit has **5 poles**.",
        "format": "markdown",
        "sha256": "10476d2f0744ffb6939b56690f39996ddd59766d43747ec32669aaa0d8c26852"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The circuit has two poles, set by the gate and output nodes; capacitors do not each create an independent pole. The answer incorrectly counts five poles.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 190,
        "total_tokens": 974,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 190,
        "total_tokens": 974,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a two-stage MOSFET amplifier with parasitic capacitances. The poles in the circuit are determined by the RC time constants formed by the resistances and capacitances in the circuit. \n\n### Key capacitances in the circuit:\n1. **\\( C_{GS} \\):** Gate-to-source capacitance of \\( M_1 \\).\n2. **\\( C_{GD} \\):** Gate-to-drain capacitance of \\( M_1 \\).\n3. **\\( C_{DB} \\):** Drain-to-bulk capacitance of \\( M_1 \\).\n4. **\\( C_{GD2} \\):** Gate-to-drain capacitance of \\( M_2 \\).\n5. **\\( C_{DB2} \\):** Drain-to-bulk capacitance of \\( M_2 \\).\n\nEach of these capacitances, in combination with the resistances in the circuit, contributes to a pole in the frequency response.\n\n### Number of poles:\n- The circuit has **five capacitances** that can introduce poles.\n- However, some capacitances may combine or interact, reducing the effective number of poles.\n- In this case, the circuit will typically have **three dominant poles** due to the three main nodes (input, intermediate, and output).\n\nThus, the circuit has **three poles**.",
        "format": "markdown",
        "sha256": "46269f10df99a521d8cb59bc1aa68c25118cd1316be8741fd8fe22d917ed6c9f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The circuit has two poles, not three. The answer incorrectly treats capacitances as producing separate poles and invents an intermediate node, though it does identify several relevant parasitic capacitances.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 272,
        "total_tokens": 1056,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 272,
        "total_tokens": 1056,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the number of poles in the circuit, we need to identify the independent energy storage elements (capacitors) that contribute to the circuit's dynamics. Each independent capacitor introduces a pole in the transfer function.\n\nFrom the circuit:\n\n1. **Capacitors present:**\n   - \\( C_{GS} \\): Gate-to-source capacitance of \\( M_1 \\).\n   - \\( C_{GD} \\): Gate-to-drain capacitance of \\( M_1 \\).\n   - \\( C_{DB} \\): Drain-to-bulk capacitance of \\( M_1 \\).\n   - \\( C_{GD2} \\): Gate-to-drain capacitance of \\( M_2 \\).\n   - \\( C_{DB2} \\): Drain-to-bulk capacitance of \\( M_2 \\).\n\n2. **Independent capacitors:**\n   Each of these capacitors is connected to different nodes in the circuit, and they are independent energy storage elements.\n\n### Conclusion:\nThe circuit has **5 poles**, corresponding to the 5 independent capacitors.",
        "format": "markdown",
        "sha256": "3e67bfd539f281f4be130ca0565ceff8d139c6ea1f5012ee46bbc2d5df46dc7f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The circuit has two poles, not five: the listed capacitors do not represent five independent node voltages. The answer identifies relevant capacitors but incorrectly counts each as an independent pole.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 216,
        "total_tokens": 1000,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 784,
        "output_tokens": 216,
        "total_tokens": 1000,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current mirror load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: The input transistor, operating in the saturation region, amplifies the input signal \\( V_{in} \\).\n2. **M2**: The current mirror transistor, which provides a constant current load for M1.\n3. **\\( R_D \\)**: A resistor connected to \\( V_{DD} \\), which converts the current through M2 into an output voltage \\( V_{out} \\).\n4. **\\( V_{DD} \\)**: The supply voltage.\n\n---\n\n### Operation:\n1. **Input Stage (M1)**:\n   - The gate of M1 is connected to the input voltage \\( V_{in} \\).\n   - As \\( V_{in} \\) increases, the drain current \\( I_{D1} \\) of M1 increases (assuming M1 is in saturation).\n   - The source of M1 is grounded, so the source voltage is 0 V.\n\n2. **Current Mirror Load (M2)**:\n   - M2 is configured as a current mirror. Its gate and drain are connected together, ensuring it operates in saturation.\n   - The current through M2, \\( I_{D2} \\), mirrors the current \\( I_{D1} \\) of M1.\n   - The current \\( I_{D2} \\) flows through \\( R_D \\), generating the output voltage \\( V_{out} \\).\n\n3. **Output Voltage (\\( V_{out} \\))**:\n   - The output voltage is given by:\n     \\[\n     V_{out} = V_{DD} - I_{D2} R_D\n     \\]\n   - As \\( V_{in} \\) increases, \\( I_{D1} \\) (and hence \\( I_{D2} \\)) increases, causing \\( V_{out} \\) to decrease.\n\n---\n\n### Key Characteristics:\n1. **Amplification**:\n   - The circuit amplifies the input signal \\( V_{in} \\) into an output voltage \\( V_{out} \\).\n   - The gain is determined by the transconductance of M1 and the load resistance \\( R_D \\).\n\n2. **High Output Impedance**:\n   - The current mirror load (M2) provides a high output impedance, improving the gain of the amplifier.\n\n3. **Linear Operation**:\n   - For small variations in \\( V_{in} \\), the circuit operates linearly, making it suitable for analog signal amplification.\n\n---\n\n### Design Considerations:\n1. **Biasing**:\n   - Proper biasing of M1 and M2 is crucial to ensure both transistors operate in the saturation region.\n   - The gate voltage of M2 is typically set by a reference current source (not shown in the diagram).\n\n2. **Voltage Swing**:\n   - The output voltage \\( V_{out} \\) is limited by the saturation voltage of M2 and the supply voltage \\( V_{DD} \\).\n\n3. **Power Consumption**:\n   - The power consumption depends on the supply voltage \\( V_{DD} \\) and the quiescent current through the circuit.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog integrated circuits, such as operational amplifiers and signal processing systems, due to its simplicity and high gain.",
        "format": "markdown",
        "sha256": "08c55005ef1ff05997505bdc29afcfe5a5bbfa47512ae3dc95328469b800c70e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies the circuit as a current-mirror amplifier. The two NMOS devices share a gate drive and form an effective longer-channel transistor, with the lower device in triode; the answer misses this central mechanism and describes incorrect device connections and operating regions.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 699,
        "total_tokens": 1479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 699,
        "total_tokens": 1479,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current mirror load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: The input transistor, operating in the saturation region, amplifies the input signal \\( V_{in} \\).\n2. **M2**: The current mirror transistor, which provides a constant current load for \\( M_1 \\).\n3. **\\( R_D \\)**: A resistor connected to \\( V_{DD} \\), which converts the current through \\( M_2 \\) into an output voltage \\( V_{out} \\).\n4. **\\( V_{DD} \\)**: The supply voltage.\n\n---\n\n### Operation:\n1. **Input Signal**:\n   - \\( V_{in} \\) is applied to the gate of \\( M_1 \\). This controls the drain current \\( I_{D1} \\) of \\( M_1 \\).\n\n2. **Current Mirror**:\n   - \\( M_2 \\) is configured as a current mirror. It ensures that the current through \\( M_2 \\) (denoted as \\( I_{D2} \\)) is equal to \\( I_{D1} \\), assuming ideal matching between \\( M_1 \\) and \\( M_2 \\).\n\n3. **Output Voltage**:\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_{D2} R_D\n     \\]\n   - Since \\( I_{D2} \\approx I_{D1} \\), \\( V_{out} \\) depends on the input signal \\( V_{in} \\) through \\( I_{D1} \\).\n\n4. **Amplification**:\n   - The circuit amplifies small variations in \\( V_{in} \\). The gain is determined by the transconductance of \\( M_1 \\) and the load resistance \\( R_D \\):\n     \\[\n     A_v = -g_m R_D\n     \\]\n     where \\( g_m \\) is the transconductance of \\( M_1 \\).\n\n---\n\n### Key Points:\n- **Biasing**: Proper biasing ensures \\( M_1 \\) and \\( M_2 \\) operate in the saturation region.\n- **Voltage Swing**: The output voltage swing is limited by \\( V_{DD} \\) and the saturation voltage of \\( M_2 \\).\n- **Matching**: For accurate current mirroring, \\( M_1 \\) and \\( M_2 \\) should be well-matched.\n\nThis circuit is commonly used in analog design for amplification purposes, particularly in integrated circuits.",
        "format": "markdown",
        "sha256": "b9a66b67c67df096ac39cc094cf2da0c7e5b2c9216845caeabfa9afbc050a409"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the tied-gate series NMOS devices as a current mirror, assigns M1 the wrong operating region, and misses the essential longer-effective-channel behavior.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 549,
        "total_tokens": 1329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 549,
        "total_tokens": 1329,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with a current mirror load**. Here's a detailed analysis:\n\n### Components:\n1. **M1**: The input transistor, operating in the saturation region, amplifies the input signal \\( V_{in} \\).\n2. **M2**: The current mirror transistor, which provides a constant current load for \\( M_1 \\).\n3. **\\( R_D \\)**: A resistor connected to \\( V_{DD} \\), which converts the current through \\( M_2 \\) into an output voltage \\( V_{out} \\).\n4. **\\( V_{DD} \\)**: The supply voltage.\n\n---\n\n### Operation:\n1. **Input Signal**:\n   - \\( V_{in} \\) is applied to the gate of \\( M_1 \\). As \\( V_{in} \\) increases, the drain current \\( I_{D1} \\) of \\( M_1 \\) increases.\n\n2. **Current Mirror**:\n   - \\( M_2 \\) is configured as a current mirror. It ensures that the current through \\( M_2 \\) (denoted as \\( I_{D2} \\)) matches \\( I_{D1} \\), assuming ideal matching between \\( M_1 \\) and \\( M_2 \\).\n\n3. **Output Voltage**:\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_{D2} R_D\n     \\]\n   - As \\( I_{D2} \\) increases (due to an increase in \\( V_{in} \\)), \\( V_{out} \\) decreases, resulting in an inverted output.\n\n4. **Amplification**:\n   - The circuit amplifies small variations in \\( V_{in} \\) into larger variations in \\( V_{out} \\), with the gain determined by the transconductance of \\( M_1 \\) and the load resistance \\( R_D \\).\n\n---\n\n### Key Equations:\n1. **Drain Current of \\( M_1 \\)**:\n   \\[\n   I_{D1} = \\frac{1}{2} k_n (V_{in} - V_{th})^2\n   \\]\n   where \\( k_n = \\mu_n C_{ox} \\frac{W}{L} \\) is the process transconductance parameter, and \\( V_{th} \\) is the threshold voltage.\n\n2. **Output Voltage**:\n   \\[\n   V_{out} = V_{DD} - I_{D1} R_D\n   \\]\n\n3. **Voltage Gain**:\n   \\[\n   A_v = -g_m R_D\n   \\]\n   where \\( g_m = \\frac{\\partial I_{D1}}{\\partial V_{in}} = k_n (V_{in} - V_{th}) \\) is the transconductance of \\( M_1 \\).\n\n---\n\n### Summary:\n- The circuit is a **common-source amplifier** with a current mirror load.\n- It provides **voltage amplification** with an inverted output.\n- The gain depends on the transconductance of \\( M_1 \\) and the load resistance \\( R_D \\).\n- The current mirror ensures a constant current load, improving linearity and gain.",
        "format": "markdown",
        "sha256": "f22556b87266749974d7a7d3e20a346f742c4057f690b98b6e95ee47ddcd2740"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the tied-gate series NMOS devices as a current mirror and assigns the wrong operating regions. It misses the essential mechanism: M1 acts in triode as a channel extension, so the pair behaves approximately like one NMOS with a longer effective channel.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 689,
        "total_tokens": 1469,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 689,
        "total_tokens": 1469,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's a detailed analysis:\n\n---\n\n### **Components and Configuration**\n1. **Transistor M1**:\n   - Acts as the main amplifying device.\n   - Its gate is driven by the input signal \\( V_{in} \\).\n   - Operates in the saturation region for amplification.\n\n2. **Transistor M2**:\n   - Acts as an active load for M1.\n   - Its gate is biased by a constant voltage \\( V_b \\), ensuring it operates in the saturation region.\n\n3. **Current Source \\( I_1 \\)**:\n   - Provides a constant current to the source of M1 and M2.\n   - Sets the operating point of the circuit.\n\n4. **Resistor \\( R_D \\)**:\n   - Converts the current through M2 into a voltage, producing the output \\( V_{out} \\).\n\n---\n\n### **Operation**\n1. **Input Signal**:\n   - The input \\( V_{in} \\) modulates the gate voltage of M1, causing variations in its drain current.\n\n2. **Current Flow**:\n   - The current through M1 is mirrored by M2 due to the constant current source \\( I_1 \\).\n   - M2 operates as a current source load, maintaining a high output impedance.\n\n3. **Output Voltage**:\n   - The output voltage \\( V_{out} \\) is taken across \\( R_D \\).\n   - As \\( V_{in} \\) increases, the drain current of M1 increases, causing a larger voltage drop across \\( R_D \\), and \\( V_{out} \\) decreases.\n\n---\n\n### **Key Equations**\n1. **Operating Regions**:\n   - M1 and M2 must operate in the saturation region for proper amplification:\n     \\[\n     V_{DS} > V_{GS} - V_{th}\n     \\]\n     where \\( V_{th} \\) is the threshold voltage.\n\n2. **Output Voltage**:\n   - The output voltage is given by:\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n     where \\( I_D \\) is the drain current of M2 (equal to \\( I_1 \\)).\n\n3. **Small-Signal Gain**:\n   - The small-signal voltage gain is approximately:\n     \\[\n     A_v = -g_{m1} R_D\n     \\]\n     where \\( g_{m1} \\) is the transconductance of M1:\n     \\[\n     g_{m1} = \\frac{2 I_{D1}}{V_{GS1} - V_{th}}\n     \\]\n\n---\n\n### **Design Considerations**\n1. **Biasing**:\n   - \\( V_b \\) must be chosen to ensure M2 operates in saturation.\n   - \\( I_1 \\) sets the quiescent current through M1 and M2.\n\n2. **Gain**:\n   - The gain depends on \\( g_{m1} \\) and \\( R_D \\). Increasing \\( R_D \\) improves gain but reduces bandwidth.\n\n3. **Output Impedance**:\n   - The output impedance is dominated by \\( R_D \\) in parallel with the output impedance of M2.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing, such as amplifiers in integrated circuits, due to its high gain and compact design.",
        "format": "markdown",
        "sha256": "50b880e2a102666c3348f7d7ad6ba62cfa9d533ffac5df94295f6dace22cf895"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the circuit as a common-source amplifier with an active load. The actual topology is a source follower driving a common-gate stage (equivalently, a source-coupled pair), so its claimed inverting gain and current-mirror behavior are incorrect.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 715,
        "total_tokens": 1495,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 715,
        "total_tokens": 1495,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **M1**: A MOSFET acting as the main amplifying transistor. Its gate is connected to the input signal \\( V_{in} \\).\n2. **M2**: A MOSFET acting as an active load. Its gate is biased with a constant voltage \\( V_b \\).\n3. **\\( R_D \\)**: A resistor connected to the drain of \\( M2 \\), which helps set the output voltage \\( V_{out} \\).\n4. **\\( I_1 \\)**: A current source providing a constant current to the circuit.\n\n---\n\n### **Operation**\n1. **Input Stage (M1)**:\n   - \\( M1 \\) operates in the saturation region for amplification.\n   - The input signal \\( V_{in} \\) modulates the gate voltage of \\( M1 \\), causing variations in its drain current.\n\n2. **Active Load (M2)**:\n   - \\( M2 \\) is configured as a current source load. Its gate is biased with a constant voltage \\( V_b \\), ensuring it operates in the saturation region.\n   - The current through \\( M2 \\) is approximately constant, determined by its gate bias \\( V_b \\).\n\n3. **Output Voltage (\\( V_{out} \\))**:\n   - The output voltage is taken at the drain of \\( M2 \\).\n   - The voltage at \\( V_{out} \\) is determined by the current through \\( R_D \\) and the resistance \\( R_D \\):\n     \\[\n     V_{out} = V_{DD} - I_D R_D\n     \\]\n     where \\( I_D \\) is the drain current of \\( M1 \\), which is modulated by \\( V_{in} \\).\n\n---\n\n### **Key Characteristics**\n1. **Voltage Gain**:\n   - The small-signal voltage gain \\( A_v \\) is given by:\n     \\[\n     A_v = -g_{m1} R_{out}\n     \\]\n     where:\n     - \\( g_{m1} \\): Transconductance of \\( M1 \\).\n     - \\( R_{out} \\): Output resistance, which is the parallel combination of \\( R_D \\) and the output resistance of \\( M2 \\).\n\n2. **Input Impedance**:\n   - The input impedance is high because the gate of \\( M1 \\) is insulated.\n\n3. **Output Impedance**:\n   - The output impedance is approximately \\( R_D \\) in parallel with the output resistance of \\( M2 \\).\n\n---\n\n### **Design Considerations**\n1. **Biasing**:\n   - Proper biasing of \\( M1 \\) and \\( M2 \\) is crucial to ensure both transistors operate in the saturation region.\n   - \\( V_b \\) must be chosen carefully to set \\( M2 \\) in saturation.\n\n2. **Load Resistance (\\( R_D \\))**:\n   - \\( R_D \\) affects the gain and output voltage swing. A larger \\( R_D \\) increases gain but reduces the output swing.\n\n3. **Current Source (\\( I_1 \\))**:\n   - \\( I_1 \\) sets the quiescent current through \\( M1 \\) and \\( M2 \\), affecting the operating point and linearity.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing as a high-gain amplifier.\n- It is also a building block in operational amplifiers and other analog integrated circuits.",
        "format": "markdown",
        "sha256": "7c43003db7db7bd4e8617ba6bc7968b2865038733c0b7defb15fe553d1ab840b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the topology as a common-source amplifier with an active load; the circuit is a source follower driving a common-gate stage (or a source-coupled differential pair).",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 745,
        "total_tokens": 1525,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 745,
        "total_tokens": 1525,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **common-source amplifier with active load**. Here's a detailed analysis:\n\n### Components and Configuration:\n1. **M1 (Input Transistor):**\n   - Acts as the main amplifying transistor.\n   - The gate of M1 is connected to the input signal \\( V_{in} \\).\n   - The source of M1 is connected to a constant current source \\( I_1 \\), which sets the bias current.\n\n2. **M2 (Active Load):**\n   - Acts as a load for M1.\n   - The gate of M2 is connected to a bias voltage \\( V_b \\), which ensures M2 operates in saturation.\n   - The drain of M2 is connected to \\( V_{DD} \\), and its source is connected to the drain of M1.\n\n3. **\\( R_D \\):**\n   - Represents the load resistance.\n   - The output voltage \\( V_{out} \\) is taken across \\( R_D \\).\n\n4. **\\( I_1 \\):**\n   - A constant current source that sets the operating point of M1.\n\n---\n\n### Operation:\n1. **Biasing:**\n   - \\( V_b \\) sets the operating point of M2, ensuring it operates in the saturation region.\n   - \\( I_1 \\) sets the bias current through M1, ensuring it also operates in the saturation region.\n\n2. **Signal Amplification:**\n   - When \\( V_{in} \\) increases, the gate-source voltage \\( V_{gs1} \\) of M1 increases, causing an increase in the drain current \\( I_{D1} \\).\n   - The increase in \\( I_{D1} \\) causes a corresponding increase in the current through M2.\n   - Since M2 is in saturation, its drain-source voltage \\( V_{ds2} \\) decreases, leading to a decrease in \\( V_{out} \\).\n   - Thus, the circuit provides an amplified and inverted output signal.\n\n3. **Active Load Behavior:**\n   - M2 acts as an active load, providing a high output impedance. This increases the voltage gain of the circuit compared to a resistive load.\n\n---\n\n### Key Equations:\n1. **Voltage Gain (\\( A_v \\)):**\n   \\[\n   A_v = -g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\( g_{m1} \\) is the transconductance of M1.\n   - \\( R_{out} \\) is the output resistance, which is primarily determined by the output impedance of M2 in parallel with \\( R_D \\).\n\n2. **Output Resistance (\\( R_{out} \\)):**\n   \\[\n   R_{out} = R_D \\parallel r_{o2}\n   \\]\n   where \\( r_{o2} \\) is the output resistance of M2.\n\n3. **Transconductance (\\( g_{m1} \\)):**\n   \\[\n   g_{m1} = \\frac{2I_{D1}}{V_{ov1}}\n   \\]\n   where \\( V_{ov1} = V_{gs1} - V_{th1} \\) is the overdrive voltage of M1.\n\n---\n\n### Design Considerations:\n1. **Bias Voltage \\( V_b \\):**\n   - Must be chosen such that M2 operates in saturation.\n   - \\( V_b > V_{gs2} - V_{th2} \\).\n\n2. **Current Source \\( I_1 \\):**\n   - Determines the bias current through M1 and M2.\n   - Must be stable to ensure consistent operation.\n\n3. **Load Resistance \\( R_D \\):**\n   - Affects the gain and output swing.\n   - Higher \\( R_D \\) increases gain but reduces the output swing.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog signal processing, such as in amplifiers and analog front-end circuits, due to its high gain and good linearity.",
        "format": "markdown",
        "sha256": "c131fdfc91d6284f2cbe02958da478f194420fac9fcd2b1136070a63bc334c9a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the circuit as a common-source amplifier with an active load and gives an inverting gain. The actual circuit is a source follower driving a common-gate stage (or a source-coupled pair), with the output at M2’s drain.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 830,
        "total_tokens": 1610,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 830,
        "total_tokens": 1610,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a **common-source amplifier with active load**, where \\( M_1 \\) is the main amplifying transistor, and \\( M_2 \\) acts as a current source load. The output impedance of this circuit can exhibit inductive behavior due to the **negative transconductance effect** of the active load transistor \\( M_2 \\).\n\n### Explanation of Inductive Output Impedance:\n\n1. **Small-Signal Model of \\( M_2 \\):**\n   - \\( M_2 \\) is configured as a current source, with its gate biased at a constant voltage \\( V_b \\).\n   - The small-signal impedance of \\( M_2 \\) at its drain (connected to \\( V_{\\text{out}} \\)) is given by:\n     \\[\n     Z_{\\text{out}} = \\frac{1}{g_{m2}} \\cdot sC_{gs2} + r_{o2}\n     \\]\n     where:\n     - \\( g_{m2} \\): Transconductance of \\( M_2 \\),\n     - \\( C_{gs2} \\): Gate-to-source capacitance of \\( M_2 \\),\n     - \\( r_{o2} \\): Output resistance of \\( M_2 \\),\n     - \\( s \\): Complex frequency variable (\\( s = j\\omega \\)).\n\n2. **Phase Shift Due to Capacitance:**\n   - The gate-to-source capacitance \\( C_{gs2} \\) introduces a phase shift in the current through \\( M_2 \\), which can result in a **negative resistance** or **inductive behavior** at the output.\n\n3. **Inductive Behavior:**\n   - The interaction between the capacitance \\( C_{gs2} \\) and the transconductance \\( g_{m2} \\) creates a frequency-dependent impedance that mimics an inductor.\n   - At higher frequencies, the impedance of \\( M_2 \\) can be approximated as:\n     \\[\n     Z_{\\text{out}} \\approx j\\omega L_{\\text{eff}}\n     \\]\n     where \\( L_{\\text{eff}} \\) is an effective inductance determined by the circuit parameters.\n\n4. **Role of \\( M_1 \\):**\n   - The transistor \\( M_1 \\) amplifies the input signal, and its output current flows through \\( M_2 \\). The inductive nature of \\( M_2 \\)'s impedance affects the overall output impedance of the circuit, making it appear inductive.\n\n### Conclusion:\nThe output impedance of the circuit can be inductive due to the **frequency-dependent behavior of the active load transistor \\( M_2 \\)**, which arises from the interaction of its transconductance \\( g_{m2} \\) and gate-to-source capacitance \\( C_{gs2} \\). This inductive behavior is particularly significant at higher frequencies.",
        "format": "markdown",
        "sha256": "16f062012bbe683b475eaac6b8ddd769f966274f7beb83ec50667a995227b0b0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies M1 as a common-source amplifier and attributes the effect to M2, missing the actual source-follower mechanism: the RS–CGS1 interaction moves Zout from about 1/gm1 toward RS. Its proposed M2 impedance explanation is also incorrect.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 600,
        "total_tokens": 1729,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 600,
        "total_tokens": 1729,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a **common-gate amplifier** with a cascode configuration (transistor \\(M_2\\) is the cascode device). The output impedance of this circuit can appear inductive due to the **negative feedback effect** created by the cascode transistor \\(M_2\\).\n\n### Explanation:\n\n1. **Cascode Configuration**:\n   - The transistor \\(M_2\\) is configured as a cascode device, which isolates the output node (\\(V_{out}\\)) from the input node (\\(V_{in}\\)).\n   - The cascode configuration increases the output impedance of the circuit by reducing the effect of the Miller capacitance and improving the voltage gain.\n\n2. **Small-Signal Model**:\n   - In the small-signal model, the impedance at the output node is determined by the interaction of the transconductance (\\(g_m\\)) of \\(M_1\\) and the impedance seen looking into the source of \\(M_2\\).\n   - The source of \\(M_2\\) is connected to the drain of \\(M_1\\), and the small-signal current through \\(M_1\\) is mirrored into \\(M_2\\).\n\n3. **Inductive Behavior**:\n   - The cascode transistor \\(M_2\\) introduces a **current-dependent voltage** at its source due to its transconductance (\\(g_{m2}\\)).\n   - This creates a **phase shift** between the current and voltage at the output node, which mimics the behavior of an inductor.\n   - Mathematically, the impedance at the output node can be expressed as:\n     \\[\n     Z_{out} \\approx \\frac{1}{g_{m1} g_{m2} C_{gs2}}\n     \\]\n     where \\(C_{gs2}\\) is the gate-source capacitance of \\(M_2\\). This impedance has an inductive nature because it increases with frequency, similar to an inductor.\n\n4. **Physical Interpretation**:\n   - The inductive behavior arises because the cascode configuration effectively converts the capacitive behavior of \\(M_2\\) into an inductive response at the output node.\n   - This is a result of the interaction between the transconductance of \\(M_1\\) and \\(M_2\\), and the capacitance \\(C_{gs2}\\).\n\n### Conclusion:\nThe output impedance of the circuit appears inductive due to the cascode configuration, which introduces a phase shift and frequency-dependent behavior that mimics an inductor. This is a common technique in analog circuit design to achieve high output impedance and improve performance in high-frequency applications.",
        "format": "markdown",
        "sha256": "480ddf871ff943071f2000e388a320123a064ddd777df3ab11ae7b328abfedce"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the source follower/current-source topology as a cascode and gives an incorrect mechanism and impedance expression. It misses the key RS–CGS1 transition that makes Zout rise with frequency.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 550,
        "total_tokens": 1679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 550,
        "total_tokens": 1679,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a **common-gate amplifier** with a cascode configuration (transistors \\(M_1\\) and \\(M_2\\)). The output impedance of this circuit can appear inductive due to the **negative feedback effect** created by the cascode structure.\n\n### Explanation:\n\n1. **Cascode Configuration**:\n   - \\(M_2\\) is the cascode transistor, and it provides a high impedance at the drain of \\(M_1\\).\n   - The gate of \\(M_2\\) is biased at a constant voltage (\\(V_b\\)), which keeps \\(M_2\\) in saturation.\n\n2. **Small-Signal Behavior**:\n   - The small-signal output impedance at \\(V_{\\text{out}}\\) is determined by the interaction between the transconductance (\\(g_m\\)) of \\(M_1\\) and the impedance seen at the source of \\(M_2\\).\n   - The source of \\(M_2\\) is connected to the drain of \\(M_1\\), and the current through \\(M_1\\) is modulated by the small-signal voltage at \\(V_{\\text{out}}\\).\n\n3. **Inductive Behavior**:\n   - The small-signal current through \\(M_1\\) is proportional to the voltage at its gate (\\(V_{\\text{in}}\\)) and its transconductance (\\(g_{m1}\\)).\n   - Due to the cascode structure, a phase shift occurs between the current and voltage at \\(V_{\\text{out}}\\), creating a behavior similar to an inductor.\n   - This phase shift arises because the current through \\(M_1\\) lags the voltage at \\(V_{\\text{out}}\\), as \\(M_2\\) introduces a feedback effect that opposes rapid changes in current.\n\n4. **Mathematical Representation**:\n   - The output impedance can be expressed as:\n     \\[\n     Z_{\\text{out}} \\approx \\frac{1}{g_{m1}C_{\\text{gs2}}}\n     \\]\n     where \\(C_{\\text{gs2}}\\) is the gate-source capacitance of \\(M_2\\).\n   - This impedance has an inductive nature because it increases with frequency, mimicking the behavior of an inductor.\n\n### Conclusion:\nThe output impedance of the circuit appears inductive due to the interaction between the transconductance of \\(M_1\\), the capacitance of \\(M_2\\), and the cascode configuration. This inductive behavior is useful in RF circuits, where it can replace physical inductors in certain applications.",
        "format": "markdown",
        "sha256": "0d8a1c8d865ca6c253f8231532e48f5ad65268771dc55a4264e52720363d4fcf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the source follower as a cascode and gives an incorrect impedance expression. It misses the key mechanism: the RS–CGS1 transition from about 1/gm1 at low frequency to RS at high frequency.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 547,
        "total_tokens": 1676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1129,
        "output_tokens": 547,
        "total_tokens": 1676,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror amplifier** with a resistive load. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **M1 and M2**: These are NMOS transistors.\n   - M2 acts as the reference transistor, setting the current \\( I_{in} \\).\n   - M1 acts as the output transistor, mirroring the current \\( I_{in} \\) to the output.\n2. **\\( R_{D1} \\)**: A resistor connected to the drain of M1, which converts the mirrored current into a voltage at \\( V_{out} \\).\n3. **\\( I_{in} \\)**: A current source that sets the reference current for the circuit.\n4. **\\( V_{DD} \\)**: The supply voltage.\n\n---\n\n### **Operation**\n1. **Current Mirror Action**:\n   - The gate and drain of M2 are connected, forcing M2 to operate in saturation.\n   - The current \\( I_{in} \\) flows through M2, setting the gate voltage \\( V_{GS} \\) of M2.\n   - Since M1 and M2 are matched transistors (same dimensions and characteristics), the same \\( V_{GS} \\) is applied to M1, causing it to mirror the current \\( I_{in} \\).\n\n2. **Output Voltage**:\n   - The current mirrored by M1 flows through \\( R_{D1} \\), generating a voltage drop across it.\n   - The output voltage \\( V_{out} \\) is given by:\n     \\[\n     V_{out} = V_{DD} - I_{out} R_{D1}\n     \\]\n     where \\( I_{out} \\approx I_{in} \\) (assuming ideal current mirroring).\n\n3. **Saturation Condition**:\n   - For M1 to remain in saturation, the drain voltage of M1 (\\( V_{out} \\)) must satisfy:\n     \\[\n     V_{out} > V_{GS} - V_{th}\n     \\]\n     where \\( V_{th} \\) is the threshold voltage of the NMOS transistors.\n\n---\n\n### **Key Observations**\n1. **Current Mirroring Accuracy**:\n   - The accuracy of the current mirror depends on how well M1 and M2 are matched and the channel length modulation effect (\\( \\lambda \\)).\n   - If \\( \\lambda \\neq 0 \\), the output current \\( I_{out} \\) will slightly deviate from \\( I_{in} \\).\n\n2. **Output Voltage Swing**:\n   - The output voltage \\( V_{out} \\) is limited by the saturation condition of M1 and the supply voltage \\( V_{DD} \\).\n\n3. **Small-Signal Gain**:\n   - The small-signal voltage gain of the circuit is approximately:\n     \\[\n     A_v = -g_m R_{D1}\n     \\]\n     where \\( g_m \\) is the transconductance of M1:\n     \\[\n     g_m = \\frac{2 I_{in}}{V_{ov}}\n     \\]\n     and \\( V_{ov} = V_{GS} - V_{th} \\) is the overdrive voltage.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog integrated circuits for current mirroring and amplification.\n- It can also serve as a basic building block in operational amplifiers and biasing circuits.",
        "format": "markdown",
        "sha256": "dd60b005181bc7f55ab51e4b928b7cd621ad782f3e5e548b6fd8e04994eb5eba"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer treats M2 as diode-connected and invents a current-mirror topology, missing the positive-feedback loop. It also misreads the input current source rather than recognizing it as injected at X to drive M1.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 713,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 713,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror amplifier** with a resistive load. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **M1 and M2**: These are NMOS transistors.\n   - M2 acts as the reference transistor, setting the current \\( I_{in} \\).\n   - M1 acts as the output transistor, mirroring the current \\( I_{in} \\) to the load.\n2. **\\( R_{D1} \\)**: This is the load resistor connected to the drain of M1.\n3. **\\( V_{DD} \\)**: The supply voltage.\n4. **\\( I_{in} \\)**: The input current source.\n5. **\\( V_{out} \\)**: The output voltage at the drain of M1.\n\n---\n\n### **Operation**\n1. **Current Mirror Action**:\n   - The gate and drain of M2 are connected, forcing M2 to operate in saturation.\n   - The current \\( I_{in} \\) flows through M2, setting its drain current.\n   - The gate voltage of M2 is shared with M1 (node \\( X \\)), ensuring that M1 operates with the same gate-source voltage (\\( V_{GS} \\)) as M2.\n   - Assuming M1 and M2 are identical (same \\( W/L \\)), the drain current of M1 (\\( I_{D1} \\)) mirrors \\( I_{in} \\).\n\n   \\[\n   I_{D1} = I_{in}\n   \\]\n\n2. **Output Voltage (\\( V_{out} \\))**:\n   - The output voltage is determined by the voltage drop across \\( R_{D1} \\) and the supply voltage \\( V_{DD} \\).\n   - Using Ohm's law:\n\n   \\[\n   V_{out} = V_{DD} - I_{D1} R_{D1}\n   \\]\n\n   Substituting \\( I_{D1} = I_{in} \\):\n\n   \\[\n   V_{out} = V_{DD} - I_{in} R_{D1}\n   \\]\n\n3. **Saturation Condition**:\n   - For M1 to remain in saturation, the drain-source voltage (\\( V_{DS1} \\)) must satisfy:\n\n   \\[\n   V_{DS1} \\geq V_{GS1} - V_{th}\n   \\]\n\n   where \\( V_{th} \\) is the threshold voltage of the NMOS transistor.\n\n   - \\( V_{DS1} = V_{out} \\), so:\n\n   \\[\n   V_{out} \\geq V_{GS1} - V_{th}\n   \\]\n\n---\n\n### **Key Observations**\n1. **Current Mirroring**:\n   - The circuit ensures that \\( I_{D1} \\approx I_{in} \\), provided M1 and M2 are well-matched.\n2. **Output Voltage**:\n   - \\( V_{out} \\) decreases as \\( I_{in} \\) increases, due to the larger voltage drop across \\( R_{D1} \\).\n3. **Design Considerations**:\n   - \\( R_{D1} \\) and \\( V_{DD} \\) must be chosen such that \\( V_{out} \\) remains within the saturation region of M1.\n   - M1 and M2 must be matched for accurate current mirroring.\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog integrated circuits for biasing and amplification purposes.",
        "format": "markdown",
        "sha256": "87305e6fbaeeb82295b135811944f74df08fbfb3fda97b76f15a63a2a8b116fb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies the circuit as a current mirror, treats M2 as diode-connected, and says the input current flows through M2. It misses the positive-feedback loop and the actual input connection, so it does not meet the limited partial-credit condition.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 734,
        "total_tokens": 1514,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 734,
        "total_tokens": 1514,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror amplifier** with a resistive load. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **M1 and M2**: These are NMOS transistors.\n   - M2 acts as the reference transistor, setting the current \\( I_{in} \\).\n   - M1 mirrors the current from M2 and drives the load \\( R_{D1} \\).\n2. **\\( I_{in} \\)**: Input current source.\n3. **\\( R_{D1} \\)**: Load resistor.\n4. **\\( V_{DD} \\)**: Supply voltage.\n5. **\\( V_{out} \\)**: Output voltage.\n\n---\n\n### **Operation**\n1. **Current Mirror Action**:\n   - The gate and drain of M2 are connected, forcing M2 to operate in saturation.\n   - The current \\( I_{in} \\) flows through M2, setting its drain current.\n   - The gate voltage of M2 is shared with M1, ensuring that M1 operates in saturation and mirrors the current \\( I_{in} \\).\n\n2. **Output Current**:\n   - Assuming M1 and M2 are identical and neglecting channel-length modulation, the drain current of M1 (\\( I_{D1} \\)) is approximately equal to \\( I_{in} \\).\n\n3. **Output Voltage**:\n   - The output voltage \\( V_{out} \\) is determined by the voltage drop across \\( R_{D1} \\):\n     \\[\n     V_{out} = V_{DD} - I_{D1} R_{D1}\n     \\]\n   - Substituting \\( I_{D1} \\approx I_{in} \\):\n     \\[\n     V_{out} = V_{DD} - I_{in} R_{D1}\n     \\]\n\n4. **Saturation Condition**:\n   - For M1 to remain in saturation, the drain-source voltage \\( V_{DS1} \\) must satisfy:\n     \\[\n     V_{DS1} \\geq V_{GS1} - V_{th}\n     \\]\n   - Here, \\( V_{GS1} \\) is the gate-source voltage of M1, and \\( V_{th} \\) is the threshold voltage of the NMOS transistor.\n\n---\n\n### **Key Observations**\n1. **Current Mirroring Accuracy**:\n   - The accuracy of the current mirror depends on the matching of M1 and M2 (e.g., same \\( W/L \\) ratio) and the neglect of channel-length modulation.\n   - If channel-length modulation is considered, the output current \\( I_{D1} \\) will slightly deviate from \\( I_{in} \\).\n\n2. **Output Voltage Range**:\n   - \\( V_{out} \\) must be high enough to keep M1 in saturation. If \\( V_{out} \\) drops too low, M1 will enter the triode region, and the current mirroring will fail.\n\n3. **Load Dependency**:\n   - The output voltage \\( V_{out} \\) depends on the load resistor \\( R_{D1} \\). A larger \\( R_{D1} \\) results in a lower \\( V_{out} \\) for a given \\( I_{in} \\).\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog integrated circuits for biasing and amplification purposes.\n- It provides a stable current source or sink and can be used in differential amplifiers, active loads, and other analog building blocks.",
        "format": "markdown",
        "sha256": "e6fce090edd2fdae0c583429c6cd89beff15310950c924fdfedac31420c0d073"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the circuit as a current mirror, incorrectly says M2 is diode-connected, and misses the positive-feedback loop. It also fails to recognize M1 as a common-source stage driven by the input-current node.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 737,
        "total_tokens": 1517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 737,
        "total_tokens": 1517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current-to-voltage converter** (transimpedance amplifier) implemented using MOSFETs. Here's a detailed analysis:\n\n---\n\n### **Circuit Description**\n1. **Input Current Source (\\(I_{in}\\))**:\n   - The circuit converts the input current (\\(I_{in}\\)) into a proportional output voltage (\\(V_{out}\\)).\n   - \\(I_{in}\\) flows through the feedback resistor (\\(R_F\\)).\n\n2. **Transistors (\\(M_1\\) and \\(M_2\\))**:\n   - \\(M_1\\): Operates as a common-source amplifier. Its gate is biased by \\(V_b\\), and its drain is connected to \\(R_{D1}\\).\n   - \\(M_2\\): Operates as a common-source amplifier with its gate connected to the drain of \\(M_1\\) (node \\(X\\)).\n\n3. **Resistors (\\(R_{D1}\\), \\(R_{D2}\\), and \\(R_F\\))**:\n   - \\(R_{D1}\\): Sets the drain voltage of \\(M_1\\) and determines the gain of the first stage.\n   - \\(R_{D2}\\): Sets the drain voltage of \\(M_2\\) and determines the gain of the second stage.\n   - \\(R_F\\): Provides feedback and converts the input current (\\(I_{in}\\)) into a voltage.\n\n4. **Power Supply (\\(V_{DD}\\))**:\n   - Provides the necessary biasing for the circuit.\n\n---\n\n### **Operation**\n1. **Input Stage**:\n   - The input current (\\(I_{in}\\)) flows through \\(R_F\\), generating a voltage drop across it.\n   - This voltage drop modulates the gate-source voltage (\\(V_{GS}\\)) of \\(M_1\\), controlling its drain current.\n\n2. **Intermediate Stage**:\n   - The drain current of \\(M_1\\) flows through \\(R_{D1}\\), creating a voltage at node \\(X\\).\n   - This voltage is applied to the gate of \\(M_2\\), controlling its operation.\n\n3. **Output Stage**:\n   - The drain current of \\(M_2\\) flows through \\(R_{D2}\\), generating the output voltage (\\(V_{out}\\)).\n   - The output voltage is proportional to the input current (\\(I_{in}\\)).\n\n---\n\n### **Key Equations**\n1. **Voltage at Node \\(X\\)**:\n   \\[\n   V_X = V_{DD} - I_{D1} R_{D1}\n   \\]\n   where \\(I_{D1}\\) is the drain current of \\(M_1\\).\n\n2. **Output Voltage (\\(V_{out}\\))**:\n   \\[\n   V_{out} = V_{DD} - I_{D2} R_{D2}\n   \\]\n   where \\(I_{D2}\\) is the drain current of \\(M_2\\).\n\n3. **Feedback Relationship**:\n   \\[\n   V_{in} = I_{in} R_F\n   \\]\n\n4. **Overall Gain**:\n   The overall transimpedance gain is approximately:\n   \\[\n   V_{out} = -I_{in} R_F \\cdot A\n   \\]\n   where \\(A\\) is the voltage gain of the two MOSFET stages.\n\n---\n\n### **Applications**\n- Photodetector circuits (e.g., converting photocurrent to voltage).\n- Precision current sensing.\n- Analog signal processing.\n\n---\n\n### **Design Considerations**\n- Proper biasing of \\(M_1\\) and \\(M_2\\) is critical for linear operation.\n- \\(R_F\\) determines the sensitivity of the circuit.\n- \\(R_{D1}\\) and \\(R_{D2}\\) influence the gain and output swing.",
        "format": "markdown",
        "sha256": "5795771a673c98f7c7b397a94b99797c1b1b88e1e7bd083f1481111a7ae9b045"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes a current-to-voltage amplifier and correctly identifies M2 as driven by node X, but misidentifies M1 as common-source and misrepresents the feedback path. Its gain formula incorrectly multiplies the feedback transimpedance by the amplifier gain.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 819,
        "total_tokens": 1599,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 819,
        "total_tokens": 1599,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current-to-voltage converter** (transimpedance amplifier) implemented using MOSFETs. Here's a detailed analysis:\n\n---\n\n### **Circuit Components and Configuration**\n1. **Input Current Source (\\(I_{in}\\))**:\n   - The circuit converts the input current (\\(I_{in}\\)) into a proportional output voltage (\\(V_{out}\\)).\n\n2. **Transistor \\(M_1\\)**:\n   - \\(M_1\\) is an NMOS transistor operating in the saturation region. It acts as a current-controlled voltage source, converting the input current into a voltage at node \\(X\\).\n\n3. **Resistor \\(R_{D1}\\)**:\n   - \\(R_{D1}\\) is the load resistor for \\(M_1\\). The voltage at node \\(X\\) is determined by the current through \\(M_1\\) and \\(R_{D1}\\).\n\n4. **Transistor \\(M_2\\)**:\n   - \\(M_2\\) is another NMOS transistor, configured as a common-source amplifier. It amplifies the signal at node \\(X\\) and drives the output voltage (\\(V_{out}\\)).\n\n5. **Resistor \\(R_{D2}\\)**:\n   - \\(R_{D2}\\) is the load resistor for \\(M_2\\). It determines the gain of the common-source amplifier.\n\n6. **Feedback Resistor (\\(R_F\\))**:\n   - \\(R_F\\) provides negative feedback, stabilizing the circuit and setting the transimpedance gain (\\(V_{out}/I_{in}\\)).\n\n7. **Bias Voltage (\\(V_b\\))**:\n   - \\(V_b\\) sets the operating point of \\(M_2\\), ensuring it operates in the saturation region.\n\n---\n\n### **Operation**\n1. **Input Stage**:\n   - The input current (\\(I_{in}\\)) flows through \\(R_F\\), generating a voltage drop across it.\n   - This voltage drop modulates the gate-source voltage (\\(V_{GS1}\\)) of \\(M_1\\), controlling its drain current.\n\n2. **Intermediate Node (\\(X\\))**:\n   - The drain current of \\(M_1\\) flows through \\(R_{D1}\\), creating a voltage at node \\(X\\).\n   - The voltage at \\(X\\) is given by:\n     \\[\n     V_X = V_{DD} - I_{D1}R_{D1}\n     \\]\n     where \\(I_{D1}\\) is the drain current of \\(M_1\\).\n\n3. **Amplification Stage**:\n   - The voltage at \\(X\\) is applied to the gate of \\(M_2\\), modulating its drain current.\n   - The drain current of \\(M_2\\) flows through \\(R_{D2}\\), generating the output voltage (\\(V_{out}\\)).\n\n4. **Output Voltage**:\n   - The output voltage is given by:\n     \\[\n     V_{out} = V_{DD} - I_{D2}R_{D2}\n     \\]\n     where \\(I_{D2}\\) is the drain current of \\(M_2\\).\n\n5. **Feedback**:\n   - The feedback resistor (\\(R_F\\)) ensures that the output voltage is proportional to the input current. The transimpedance gain is approximately:\n     \\[\n     V_{out} = -I_{in}R_F\n     \\]\n\n---\n\n### **Key Observations**\n1. **Negative Feedback**:\n   - The feedback through \\(R_F\\) stabilizes the circuit and ensures linear operation.\n\n2. **Transimpedance Gain**:\n   - The gain is primarily determined by \\(R_F\\), with minor dependence on the MOSFET parameters.\n\n3. **Design Considerations**:\n   - \\(R_{D1}\\) and \\(R_{D2}\\) should be chosen to ensure proper biasing and gain.\n   - \\(V_b\\) must be set to keep \\(M_2\\) in saturation.\n\n---\n\n### **Applications**\n- Photodetector circuits (e.g., converting photocurrent to voltage).\n- Current sensing in analog systems.\n- Precision measurement systems.",
        "format": "markdown",
        "sha256": "23b5334ab9674377cb4caf987ef51d3d0637681a8603e7535b1445611a5fec12"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly recognizes a transimpedance amplifier with negative feedback and gives the approximate \u0000−RF\u0000 gain, but misidentifies the input operation: M1 is not described as a common-gate device with its gate at Vb and input at its source, and it incorrectly assigns Vb to M2. These connection errors cap the score at 2.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 893,
        "total_tokens": 1673,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 893,
        "total_tokens": 1673,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current-to-voltage converter** (transimpedance amplifier) implemented using MOSFETs. Here's a detailed analysis:\n\n---\n\n### **Circuit Components and Configuration**\n1. **Input Current Source (\\(I_{in}\\))**:\n   - The circuit converts the input current (\\(I_{in}\\)) into a proportional output voltage (\\(V_{out}\\)).\n\n2. **Transistor \\(M_1\\)**:\n   - \\(M_1\\) is an NMOS transistor operating in saturation mode. It acts as a current-controlled voltage source, converting the input current into a voltage at node \\(X\\).\n\n3. **Resistor \\(R_{D1}\\)**:\n   - \\(R_{D1}\\) is the load resistor for \\(M_1\\). The voltage at node \\(X\\) is determined by the current through \\(M_1\\) and \\(R_{D1}\\).\n\n4. **Transistor \\(M_2\\)**:\n   - \\(M_2\\) is another NMOS transistor, configured as a common-source amplifier. It amplifies the signal at node \\(X\\) and drives the output voltage (\\(V_{out}\\)).\n\n5. **Resistor \\(R_{D2}\\)**:\n   - \\(R_{D2}\\) is the load resistor for \\(M_2\\). It determines the gain of the common-source amplifier.\n\n6. **Feedback Resistor (\\(R_F\\))**:\n   - \\(R_F\\) provides negative feedback, stabilizing the circuit and setting the transimpedance gain (\\(V_{out}/I_{in}\\)).\n\n7. **Bias Voltage (\\(V_b\\))**:\n   - \\(V_b\\) sets the operating point of \\(M_2\\), ensuring it operates in saturation mode.\n\n---\n\n### **Operation and Analysis**\n1. **Input Stage (\\(M_1\\) and \\(R_{D1}\\))**:\n   - The input current (\\(I_{in}\\)) flows through \\(M_1\\) and \\(R_F\\).\n   - The voltage at node \\(X\\) is given by:\n     \\[\n     V_X = V_{DD} - I_{in} \\cdot R_{D1}\n     \\]\n\n2. **Amplification Stage (\\(M_2\\) and \\(R_{D2}\\))**:\n   - The voltage at node \\(X\\) is applied to the gate of \\(M_2\\), which amplifies the signal.\n   - The output voltage (\\(V_{out}\\)) is determined by the current through \\(R_{D2}\\):\n     \\[\n     V_{out} = V_{DD} - I_{D2} \\cdot R_{D2}\n     \\]\n   - \\(I_{D2}\\) is the drain current of \\(M_2\\), which depends on the voltage at node \\(X\\).\n\n3. **Feedback Mechanism**:\n   - The feedback resistor (\\(R_F\\)) ensures that the output voltage (\\(V_{out}\\)) is proportional to the input current (\\(I_{in}\\)).\n   - The transimpedance gain is approximately:\n     \\[\n     V_{out} = -I_{in} \\cdot R_F\n     \\]\n\n---\n\n### **Key Observations**\n- The circuit provides a linear relationship between the input current (\\(I_{in}\\)) and the output voltage (\\(V_{out}\\)).\n- Negative feedback via \\(R_F\\) improves stability and reduces sensitivity to variations in transistor parameters.\n- The gain of the circuit is primarily determined by \\(R_F\\), with minor contributions from \\(R_{D1}\\) and \\(R_{D2}\\).\n\n---\n\n### **Applications**\n- This circuit is commonly used in photodetector systems, where a photodiode generates a current proportional to incident light intensity.\n- It is also used in current sensing and signal conditioning applications.",
        "format": "markdown",
        "sha256": "b7a187db3f6e02701524c25e1052da2a11605383e1e3607f000daaed1c9231f7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly recognizes a transimpedance amplifier, the common-source M2 stage driven by X, and negative feedback with an approximate −RF gain. However, it misassigns Vb to M2 and fails to identify M1 as the common-gate input device, so it misses a central circuit connection; its direct expression for VX also ignores the feedback action.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 824,
        "total_tokens": 1604,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 824,
        "total_tokens": 1604,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror amplifier** with a differential input current source. Here's a detailed analysis:\n\n---\n\n### **Circuit Components**\n1. **Transistors**:\n   - \\( M_1 \\): NMOS transistor acting as the input device.\n   - \\( M_2 \\): NMOS transistor acting as the current mirror load.\n\n2. **Current Sources**:\n   - \\( I_{in} \\): Input current source.\n   - \\( I_1 \\): Bias current source.\n\n3. **Voltage Sources**:\n   - \\( V_b \\): Bias voltage applied to the gate of \\( M_1 \\).\n   - \\( V_{DD} \\): Supply voltage.\n\n4. **Output**:\n   - \\( V_{out} \\): Output voltage at the drain of \\( M_2 \\).\n\n---\n\n### **Operation**\n1. **Input Current \\( I_{in} \\)**:\n   - The input current \\( I_{in} \\) flows into the source of \\( M_1 \\), creating a voltage drop across \\( M_1 \\) based on its gate-source voltage (\\( V_{GS1} \\)).\n\n2. **Bias Voltage \\( V_b \\)**:\n   - \\( V_b \\) sets the operating point of \\( M_1 \\), ensuring it operates in the saturation region.\n\n3. **Current Mirror Action**:\n   - \\( M_2 \\) is configured as a current mirror load. The gate of \\( M_2 \\) is connected to the gate of \\( M_1 \\), ensuring that \\( M_2 \\) mirrors the current flowing through \\( M_1 \\).\n\n4. **Output Voltage \\( V_{out} \\)**:\n   - The output voltage \\( V_{out} \\) is determined by the current through \\( M_2 \\) and the load resistance (if any). Since \\( M_2 \\) mirrors the current of \\( M_1 \\), \\( V_{out} \\) depends on \\( I_{in} \\) and the characteristics of \\( M_2 \\).\n\n---\n\n### **Key Equations**\n1. **Current through \\( M_1 \\)**:\n   \\[\n   I_{D1} = I_{in}\n   \\]\n\n2. **Current through \\( M_2 \\)**:\n   \\[\n   I_{D2} = I_{D1} = I_{in}\n   \\]\n\n3. **Output Voltage \\( V_{out} \\)**:\n   \\[\n   V_{out} = V_{DD} - I_{D2} \\cdot R_{load}\n   \\]\n   (If there is no explicit load resistor, \\( V_{out} \\) is determined by the saturation voltage of \\( M_2 \\).)\n\n---\n\n### **Applications**\n- This circuit is commonly used in analog signal processing as a **current amplifier** or **current-to-voltage converter**.\n- It can also serve as a building block in operational amplifiers or differential amplifiers.\n\n---\n\n### **Assumptions**\n- Both transistors \\( M_1 \\) and \\( M_2 \\) are operating in the saturation region.\n- The current mirror is ideal, meaning \\( M_2 \\) perfectly mirrors the current of \\( M_1 \\).",
        "format": "markdown",
        "sha256": "63623d66c0796d67a5abc015264f4c18282c1a472847e4398fba0b8983979ef3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "Misidentifies M2 as an NMOS current-mirror load and misses its PMOS feedback connection to the input node. It does not describe the feedback loop or the circuit’s low-input-resistance/current-buffer behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 672,
        "total_tokens": 1452,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 672,
        "total_tokens": 1452,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror with a cascode configuration**. Here's a detailed analysis:\n\n### Components:\n1. **M1 and M2**: These are NMOS transistors.\n2. **\\( I_1 \\)**: A reference current source.\n3. **\\( I_{in} \\)**: The input current source.\n4. **\\( V_b \\)**: A bias voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{DD} \\)**: The supply voltage.\n6. **\\( V_{out} \\)**: The output voltage.\n\n---\n\n### Operation:\n1. **Current Mirror Functionality**:\n   - The circuit is designed to replicate the input current \\( I_{in} \\) at the output node \\( V_{out} \\).\n   - \\( M_1 \\) and \\( M_2 \\) form the current mirror. The gate and drain of \\( M_2 \\) are connected, ensuring that \\( M_2 \\) operates in saturation and sets the reference current \\( I_1 \\).\n\n2. **Cascode Configuration**:\n   - \\( M_1 \\) is the cascode transistor. Its gate is biased by \\( V_b \\), which ensures that \\( M_1 \\) operates in saturation.\n   - The cascode configuration improves the output impedance of the circuit, enhancing the current mirror's accuracy and reducing the effect of variations in \\( V_{out} \\).\n\n3. **Biasing**:\n   - \\( V_b \\) is chosen such that \\( M_1 \\) remains in saturation. This is typically set as:\n     \\[\n     V_b = V_{GS1} + V_{DS(sat)}\n     \\]\n     where \\( V_{GS1} \\) is the gate-source voltage of \\( M_1 \\), and \\( V_{DS(sat)} \\) is the minimum drain-source voltage required for \\( M_1 \\) to stay in saturation.\n\n4. **Output Current**:\n   - The output current \\( I_{out} \\) at \\( V_{out} \\) is ideally equal to \\( I_{in} \\), assuming perfect matching between \\( M_1 \\) and \\( M_2 \\).\n\n---\n\n### Advantages of the Cascode Configuration:\n1. **High Output Impedance**:\n   - The cascode configuration increases the output impedance, making the current mirror less sensitive to changes in \\( V_{out} \\).\n\n2. **Improved Accuracy**:\n   - The cascode transistor \\( M_1 \\) shields \\( M_2 \\) from variations in \\( V_{out} \\), ensuring that \\( M_2 \\) operates in saturation and maintains a constant current.\n\n3. **Reduced Channel-Length Modulation**:\n   - The cascode configuration minimizes the effect of channel-length modulation, improving the current mirror's performance.\n\n---\n\n### Applications:\n- This circuit is commonly used in analog integrated circuits for biasing and as a current source or sink.\n- The cascode configuration is particularly useful in high-performance analog designs where high output impedance and accuracy are critical.",
        "format": "markdown",
        "sha256": "0542973e477f438c3f45871329b49ad35ad6062afca5705581ea647fe019ca9c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads the topology as an NMOS current mirror/cascode, treats M2 as diode-connected, and misses the PMOS feedback path and low-input-resistance current-buffer behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 639,
        "total_tokens": 1419,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 639,
        "total_tokens": 1419,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "This circuit is a **current mirror with a cascode configuration**. Here's a detailed analysis:\n\n### Components:\n1. **M1 and M2**: These are NMOS transistors.\n2. **\\( I_1 \\)**: A reference current source.\n3. **\\( I_{in} \\)**: The input current source.\n4. **\\( V_b \\)**: A bias voltage applied to the gate of \\( M_1 \\).\n5. **\\( V_{DD} \\)**: The supply voltage.\n6. **\\( V_{out} \\)**: The output voltage.\n\n---\n\n### Operation:\n1. **Current Mirror Functionality**:\n   - \\( M_2 \\) is configured as a diode-connected transistor (its gate and drain are shorted).\n   - The reference current \\( I_1 \\) flows through \\( M_2 \\), setting its gate voltage.\n   - This gate voltage is mirrored to \\( M_1 \\), ensuring that \\( M_1 \\) also conducts a current proportional to \\( I_1 \\).\n\n2. **Cascode Configuration**:\n   - \\( M_1 \\) is the cascode transistor, with its gate biased by \\( V_b \\).\n   - The cascode configuration improves the output resistance of the current mirror, enhancing its performance by reducing the effect of \\( V_{out} \\) on the output current.\n\n3. **Output Current**:\n   - The output current \\( I_{out} \\) (flowing through \\( M_1 \\)) is ideally equal to \\( I_1 \\), assuming perfect mirroring and negligible channel-length modulation.\n\n4. **Bias Voltage \\( V_b \\)**:\n   - \\( V_b \\) sets the operating point of \\( M_1 \\), ensuring it remains in saturation for proper operation.\n   - \\( V_b \\) must be chosen such that \\( V_{DS} \\) of \\( M_1 \\) is sufficient to keep it in saturation.\n\n---\n\n### Key Features:\n1. **High Output Resistance**:\n   - The cascode configuration increases the output resistance, making the current mirror less sensitive to variations in \\( V_{out} \\).\n\n2. **Improved Accuracy**:\n   - The cascode structure reduces the effect of channel-length modulation, improving the accuracy of current mirroring.\n\n3. **Applications**:\n   - This circuit is commonly used in analog integrated circuits for biasing and as a current source with high output impedance.\n\n---\n\n### Design Considerations:\n1. **Saturation Conditions**:\n   - Both \\( M_1 \\) and \\( M_2 \\) must operate in the saturation region for proper mirroring.\n   - \\( V_{DS} \\) of \\( M_1 \\) and \\( M_2 \\) must satisfy the condition \\( V_{DS} \\geq V_{GS} - V_{th} \\).\n\n2. **Bias Voltage \\( V_b \\)**:\n   - \\( V_b \\) must be carefully chosen to ensure \\( M_1 \\) operates in saturation while maintaining a sufficient voltage drop across \\( M_2 \\).\n\n3. **Matching of Transistors**:\n   - \\( M_1 \\) and \\( M_2 \\) should be well-matched (same dimensions and process parameters) to ensure accurate current mirroring.\n\n---\n\n### Summary:\nThis circuit is a cascode current mirror, designed to provide a high-accuracy current source with high output resistance. It is widely used in analog circuit design for biasing and current reference applications.",
        "format": "markdown",
        "sha256": "363d01c0e98463e36bb681e58e83afb7a7863f3e4dee550b6b5b2b34c9f42eca"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads M2 as an NMOS diode-connected mirror device and describes a cascode current mirror, missing the PMOS feedback path and the circuit’s low-input-resistance current-buffer behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 725,
        "total_tokens": 1505,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 780,
        "output_tokens": 725,
        "total_tokens": 1505,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit will fail to oscillate if the three capacitors \\( C_L \\) become arbitrarily large. Here's why:\n\nThe circuit shown is a ring oscillator, which relies on the propagation delay of the inverters and the capacitive loading at each stage to determine its oscillation frequency. The capacitors \\( C_L \\) at each stage increase the load on the inverters, thereby increasing the propagation delay.\n\nIf \\( C_L \\) becomes arbitrarily large, the propagation delay of each inverter will increase significantly, and the circuit may reach a point where the inverters cannot switch states fast enough to sustain oscillation. In the extreme case, the circuit may become too slow to oscillate at all, effectively failing to oscillate.\n\nThus, the oscillation of the circuit depends on the capacitive loading, and excessively large \\( C_L \\) values can prevent the circuit from functioning as an oscillator.",
        "format": "markdown",
        "sha256": "974f1fd72244c2bbb9b4df1393b2eb8f011c29d64894a88b011e05211d7fab94"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer reaches the opposite conclusion: equal capacitors at all three nodes slow the ring and lower its frequency, but do not stop oscillation. It correctly notes that loading increases delay, but wrongly concludes that arbitrarily large delay prevents oscillation.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1472,
        "output_tokens": 184,
        "total_tokens": 1656,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1472,
        "output_tokens": 184,
        "total_tokens": 1656,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit will fail to oscillate if the three capacitors \\( C_L \\) become arbitrarily large. Here's why:\n\nThe circuit shown is a ring oscillator, which relies on the propagation delay of the inverters and the capacitive loading at each stage to generate oscillations. The oscillation frequency is inversely proportional to the total delay in the loop.\n\nIf the capacitors \\( C_L \\) become arbitrarily large, the capacitive loading at each stage increases significantly. This increases the charging and discharging time of the capacitors, which in turn increases the propagation delay of each inverter stage. As the capacitors grow larger, the delay becomes so large that the circuit cannot complete a full oscillation within a reasonable time frame, effectively halting oscillation.\n\nIn the extreme case where \\( C_L \\to \\infty \\), the circuit would behave as if it were stuck in a static state, as the capacitors would take an infinite amount of time to charge or discharge. Thus, the circuit fails to oscillate.",
        "format": "markdown",
        "sha256": "cbf4561d90176551a84a65e4b91fe95daf59eb17aaf343eeb357155afbe76114"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that larger capacitors increase inverter delay, but wrongly concludes the ring stops oscillating. For arbitrarily large finite capacitances, it continues oscillating at a lower frequency.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1472,
        "output_tokens": 210,
        "total_tokens": 1682,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1472,
        "output_tokens": 210,
        "total_tokens": 1682,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit will fail to oscillate if the three capacitors \\( C_L \\) become arbitrarily large. Here's why:\n\n1. **Increased Time Constant**: The capacitors \\( C_L \\) in the circuit, combined with the resistance of the inverters, determine the time constant of the circuit. If \\( C_L \\) becomes very large, the time constant increases significantly, causing the charging and discharging of the capacitors to slow down.\n\n2. **Loss of Oscillation**: For the circuit to oscillate, the signal must propagate through the inverters and return to the starting point with the correct timing and phase. If the capacitors are too large, the delay introduced by the charging and discharging process becomes so long that the circuit may no longer meet the conditions for oscillation.\n\n3. **Practical Limitations**: In practical terms, the inverters have finite drive strength and cannot charge or discharge arbitrarily large capacitors effectively. This further contributes to the failure of oscillation.\n\nThus, if \\( C_L \\) becomes arbitrarily large, the circuit will fail to oscillate due to excessive delay and the inability of the inverters to drive the capacitors.",
        "format": "markdown",
        "sha256": "d2a5d06b242693e08d5107991ce67eaec56bb9fa5aaad7e25c953d7fad75c311"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that larger capacitors increase delay, but incorrectly concludes that this makes the ring stop oscillating. With equal loading at all three nodes, the circuit continues oscillating at a lower frequency.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1472,
        "output_tokens": 245,
        "total_tokens": 1717,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1472,
        "output_tokens": 245,
        "total_tokens": 1717,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, the capacitors \\( C_L \\) represent the load capacitance at each stage of the ring oscillator. The phase noise of a ring oscillator is influenced by the load capacitance because it affects the oscillation frequency and the noise characteristics.\n\nIf the capacitors \\( C_L \\) are doubled:\n\n1. **Oscillation Frequency Decreases**: The oscillation frequency of the ring oscillator is inversely proportional to the load capacitance. Doubling \\( C_L \\) increases the delay per stage, reducing the oscillation frequency.\n\n2. **Phase Noise Increases**: Phase noise is inversely proportional to the oscillation frequency. A lower oscillation frequency results in higher phase noise. Additionally, larger capacitance increases the energy stored and dissipated per cycle, which can also contribute to increased phase noise.\n\n### Conclusion:\nDoubling the capacitors \\( C_L \\) will increase the phase noise of the ring oscillator.",
        "format": "markdown",
        "sha256": "2232d35dae16466775fe068e6554d06498c878f871ed6c5c1cedf5142b642088"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly says doubling the capacitors lowers the oscillation frequency, but reaches the opposite phase-noise conclusion. At a fixed offset frequency, the lower oscillation frequency reduces phase noise by about a factor of four (6 dB), rather than increasing it.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 190,
        "total_tokens": 1659,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 190,
        "total_tokens": 1659,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, the capacitors \\( C_L \\) are part of a ring oscillator. The phase noise of a ring oscillator is influenced by the capacitive load, as it affects the oscillation frequency and the noise performance.\n\nIf the capacitors \\( C_L \\) are doubled:\n\n1. **Oscillation Frequency**: The oscillation frequency of the ring oscillator is inversely proportional to the capacitive load. Doubling \\( C_L \\) will reduce the oscillation frequency.\n\n2. **Phase Noise**: Phase noise is inversely proportional to the oscillation frequency. A lower oscillation frequency (caused by the increased capacitance) will result in higher phase noise. Additionally, the increased capacitance increases the energy stored in the circuit, which can also contribute to higher phase noise.\n\n### Conclusion:\nDoubling the capacitors \\( C_L \\) will increase the phase noise of the ring oscillator.",
        "format": "markdown",
        "sha256": "1476e354cac180e2e5cf75d151287368e94815a206bb53b16504a568a7d70a7a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "Correctly notes that doubling the load capacitance lowers the oscillation frequency, but reaches the opposite phase-noise conclusion: at a fixed offset frequency, phase noise decreases by about a factor of four, not increases.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 185,
        "total_tokens": 1654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 185,
        "total_tokens": 1654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, the capacitors \\( C_L \\) are part of a ring oscillator. The phase noise of a ring oscillator is influenced by the capacitive load, as it affects the oscillation frequency and the noise performance.\n\nIf the capacitors \\( C_L \\) are doubled:\n\n1. **Oscillation Frequency**: The oscillation frequency of the ring oscillator is inversely proportional to the capacitive load. Doubling \\( C_L \\) will reduce the oscillation frequency.\n\n2. **Phase Noise**: Phase noise is inversely proportional to the oscillation frequency. A lower oscillation frequency (caused by the increased capacitance) will result in higher phase noise. Additionally, the increased capacitance increases the energy stored in the circuit, which can also contribute to higher phase noise.\n\n### Conclusion:\nDoubling the capacitors \\( C_L \\) will increase the phase noise of the ring oscillator.",
        "format": "markdown",
        "sha256": "1476e354cac180e2e5cf75d151287368e94815a206bb53b16504a568a7d70a7a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "Correctly notes that doubling the load capacitance lowers the oscillation frequency, but reaches the opposite phase-noise conclusion: at a fixed offset frequency, phase noise decreases by about a factor of four, not increases.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 185,
        "total_tokens": 1654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 185,
        "total_tokens": 1654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit may fail to oscillate if \\( C_L \\) becomes arbitrarily large. Here's why:\n\nThe circuit shown is a ring oscillator, which relies on the propagation delay of the inverters to produce oscillations. The load capacitance \\( C_L \\) at the output of one of the inverters affects the propagation delay. As \\( C_L \\) increases, the delay per stage increases because the inverter takes longer to charge and discharge the capacitor.\n\nIf \\( C_L \\) becomes excessively large, the delay may become so significant that the circuit cannot sustain oscillations. This happens because the total delay around the loop may exceed the ability of the circuit to transition states within a reasonable time frame, effectively damping the oscillations. In extreme cases, the circuit may settle into a static state instead of oscillating.\n\nThus, while the circuit can tolerate some increase in \\( C_L \\), an arbitrarily large \\( C_L \\) can prevent oscillation.",
        "format": "markdown",
        "sha256": "689d1248c7e28a9eeea983023e2368151cd1383ac3c352eb59f1752c66ed0cad"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that an arbitrarily large load on one node can stop oscillation and recognizes that it makes the node slower, potentially leaving the circuit static. However, the explanation treats excessive total delay as the cause rather than identifying the dominant-pole gain/phase roll-off (or the corresponding slow-node, finite-gain loop behavior).",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit may fail to oscillate if \\( C_L \\) becomes arbitrarily large. Here's why:\n\nThe circuit shown is a ring oscillator, which relies on the propagation delay of the inverters to produce oscillations. The load capacitance \\( C_L \\) at the output of one of the inverters affects the propagation delay. As \\( C_L \\) increases, the delay per stage increases because the inverter takes longer to charge and discharge the capacitor.\n\nIf \\( C_L \\) becomes excessively large, the delay may become so significant that the circuit cannot sustain oscillations. This happens because the total delay around the loop may exceed the ability of the circuit to transition states within a reasonable time frame, effectively damping the oscillations. In extreme cases, the circuit may settle into a static state instead of oscillating.\n\nThus, while the circuit can tolerate some increase in \\( C_L \\), an arbitrarily large \\( C_L \\) can prevent oscillation.",
        "format": "markdown",
        "sha256": "689d1248c7e28a9eeea983023e2368151cd1383ac3c352eb59f1752c66ed0cad"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that an arbitrarily large load on one node can stop oscillation and recognizes that it makes the node slower, potentially leaving the circuit static. However, the explanation treats excessive total delay as the cause rather than identifying the dominant-pole gain/phase roll-off (or the corresponding slow-node, finite-gain loop behavior).",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit may fail to oscillate if \\( C_L \\) becomes arbitrarily large. Here's why:\n\nThe circuit shown is a ring oscillator, which relies on the propagation delay of the inverters to produce oscillations. The load capacitance \\( C_L \\) at the output of one of the inverters affects the propagation delay. As \\( C_L \\) increases, the delay per stage increases because the inverter takes longer to charge and discharge the capacitor.\n\nIf \\( C_L \\) becomes excessively large, the delay may become so significant that the circuit cannot sustain oscillations. This happens because the total delay around the loop may exceed the ability of the circuit to transition states within a reasonable time frame, effectively damping the oscillations. In extreme cases, the circuit may settle into a static state instead of oscillating.\n\nThus, while the circuit can tolerate some increase in \\( C_L \\), an arbitrarily large \\( C_L \\) can prevent oscillation.",
        "format": "markdown",
        "sha256": "689d1248c7e28a9eeea983023e2368151cd1383ac3c352eb59f1752c66ed0cad"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that an arbitrarily large load on one node can stop oscillation and recognizes that it makes the node slower, potentially leaving the circuit static. However, the explanation treats excessive total delay as the cause rather than identifying the dominant-pole gain/phase roll-off (or the corresponding slow-node, finite-gain loop behavior).",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1280,
        "input_tokens": 1469,
        "output_tokens": 195,
        "total_tokens": 1664,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling the widths of the NMOS and PMOS devices in the circuit affects the phase noise as follows:\n\n1. **Reduction in Phase Noise**: Doubling the transistor widths increases the transconductance (\\(g_m\\)) of the devices. Higher transconductance improves the circuit's ability to drive the load and reduces the thermal noise contribution, which is a key component of phase noise.\n\n2. **Increased Capacitance**: Doubling the widths also increases the parasitic capacitances (gate-to-source, gate-to-drain, etc.). This can slightly reduce the oscillation frequency and may affect the phase noise at higher offset frequencies due to slower transitions.\n\n3. **Improved Signal-to-Noise Ratio (SNR)**: The increased current drive capability of wider transistors improves the signal amplitude, which enhances the SNR and reduces phase noise.\n\nIn summary, doubling the widths of the NMOS and PMOS devices generally reduces the phase noise due to improved transconductance and SNR, but the increased parasitic capacitance may introduce trade-offs in certain frequency ranges.",
        "format": "markdown",
        "sha256": "4a3f9570551d21d7f2986e2a7a184aeb1a1c18c7d89eee567de1870f54332848"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly says phase noise decreases, but gives no magnitude (the reduction is about 3 dB) and attributes it to reduced thermal noise. Device noise current actually increases with width; the result comes from signal scaling, with node capacitance and current both doubling so frequency stays about the same.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 220,
        "total_tokens": 1356,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 220,
        "total_tokens": 1356,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling the widths of the NMOS and PMOS devices in the circuit affects the phase noise as follows:\n\n1. **Reduction in Phase Noise**: Doubling the transistor widths increases the transconductance (\\(g_m\\)) of the devices. Higher transconductance improves the circuit's ability to drive the load and reduces the thermal noise contribution, which is a significant component of phase noise.\n\n2. **Increased Capacitance**: Doubling the widths also increases the parasitic capacitances (gate-to-source, gate-to-drain, etc.). This can slightly reduce the oscillation frequency and may affect the phase noise at higher offset frequencies due to slower transitions.\n\n3. **Improved Signal-to-Noise Ratio (SNR)**: The increased current drive capability of wider transistors improves the signal amplitude, which enhances the SNR and reduces phase noise.\n\nIn summary, doubling the widths of the NMOS and PMOS devices generally reduces the phase noise due to improved transconductance and SNR, but the increased parasitic capacitance may have secondary effects depending on the operating frequency and circuit design.",
        "format": "markdown",
        "sha256": "9abe63bc32f0147aec6b721346182c0f2e3a706fa1ab0ee6e8da3eee204c954a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly predicts that phase noise decreases, but omits the key approximately 3 dB amount and gives misleading reasoning: device noise current increases with width, and the oscillation frequency stays about the same.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 224,
        "total_tokens": 1360,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 224,
        "total_tokens": 1360,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Doubling the widths of the NMOS and PMOS devices in the circuit affects the phase noise as follows:\n\n1. **Reduction in Phase Noise**: Doubling the transistor widths increases the transconductance (\\(g_m\\)) of the devices. Higher transconductance improves the circuit's ability to drive the load and reduces the thermal noise contribution, which is a key component of phase noise.\n\n2. **Increased Capacitance**: Doubling the widths also increases the parasitic capacitances (gate-to-source, gate-to-drain, etc.). This can slightly reduce the oscillation frequency and may affect the phase noise at higher offset frequencies due to slower transitions.\n\n3. **Improved Signal-to-Noise Ratio (SNR)**: The increased current handling capability of wider transistors improves the SNR, which directly reduces phase noise.\n\nIn summary, doubling the widths of the NMOS and PMOS devices generally reduces the phase noise due to improved transconductance and reduced thermal noise, but the increased parasitic capacitance may slightly affect the high-frequency performance.",
        "format": "markdown",
        "sha256": "7b9891b3dce32b21335ccfa09dcb809d2ca231018f4a4bddc45a4538a4cbab51"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It gets the direction right but gives no magnitude; the expected reduction is about 3 dB. Its explanation is also flawed: device noise current increases with width, while drive current and node capacitance both double, leaving frequency roughly unchanged.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 216,
        "total_tokens": 1352,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 216,
        "total_tokens": 1352,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance seen looking into the supply node of the ring oscillator, we analyze the circuit as follows:\n\n### Key Observations:\n1. **Ring Oscillator Structure**: The circuit consists of three inverters connected in a loop, with their supply nodes tied together at the node labeled \\( R_X \\).\n2. **Small-Signal Model**: Each inverter can be modeled as a small-signal equivalent circuit, where the supply current depends on the small-signal resistance of the transistors in the inverter.\n\n### Small-Signal Resistance Analysis:\n- Each inverter contributes a small-signal resistance to the supply node. This resistance is primarily determined by the output impedance of the transistors in the inverter.\n- Assuming the inverters are identical, the small-signal resistance seen at the supply node is the parallel combination of the small-signal resistances of the three inverters.\n\nLet the small-signal resistance of each inverter be \\( r_{inv} \\). Then, the total resistance \\( R_X \\) seen at the supply node is:\n\n\\[\nR_X = \\frac{r_{inv}}{3}\n\\]\n\n### Conclusion:\nThe small-signal resistance seen looking into the supply node of the ring oscillator is the parallel combination of the small-signal resistances of the three inverters. If \\( r_{inv} \\) is the small-signal resistance of a single inverter, the total resistance is:\n\n\\[\nR_X = \\frac{r_{inv}}{3}.\n\\]",
        "format": "markdown",
        "sha256": "a24f0b9177bb0fc8498c40389e503f580a9d02c835ae176159a24872de2f3441"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that the three inverters share the supply, but incorrectly treats the resistance as a parallel combination of transistor output impedances. It misses the dominant oscillation-driven charging and discharging of the load capacitances and gives no valid expression for the resistance.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1132,
        "output_tokens": 307,
        "total_tokens": 1439,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1132,
        "output_tokens": 307,
        "total_tokens": 1439,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance seen looking into the supply node of the ring oscillator, we analyze the circuit as follows:\n\n### Key Observations:\n1. **Ring Oscillator Structure**: The circuit consists of three inverters connected in a loop, with their supply nodes tied together at the node labeled \\( R_X \\).\n2. **Small-Signal Model**: Each inverter can be modeled as a small-signal equivalent circuit, where the supply current depends on the small-signal resistance of the transistors in the inverter.\n\n### Small-Signal Resistance Analysis:\n- Each inverter contributes a small-signal resistance to the supply node. This resistance is primarily determined by the output impedance of the transistors in the inverter.\n- Assuming the inverters are identical, the small-signal resistance of each inverter at the supply node is \\( r_o \\), where \\( r_o \\) is the output resistance of the transistors in the inverter.\n\n### Combining Resistances:\n- Since the three inverters are connected in parallel at the supply node, the equivalent small-signal resistance \\( R_X \\) seen at the supply node is the parallel combination of the small-signal resistances of the three inverters:\n  \\[\n  R_X = \\frac{r_o}{3}\n  \\]\n  where \\( r_o \\) is the small-signal resistance of a single inverter.\n\n### Final Answer:\nThe small-signal resistance seen looking into the supply node of the ring oscillator is:\n\\[\nR_X = \\frac{r_o}{3}\n\\]",
        "format": "markdown",
        "sha256": "4564c37059ba25b663c976097104d1d653aa0889de7f006afabc1c04c6a775c9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer treats the supply resistance as three transistor output resistances in parallel and ignores the oscillation-driven charging and discharging of the load capacitances, which sets the resistance in the golden solution.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1132,
        "output_tokens": 314,
        "total_tokens": 1446,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1132,
        "output_tokens": 314,
        "total_tokens": 1446,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance seen looking into the supply node of the ring oscillator, we analyze the circuit as follows:\n\n### Key Observations:\n1. **Ring Oscillator Structure**: The circuit consists of three inverters connected in a loop, with their supply nodes tied together at the node labeled \\( R_X \\).\n2. **Small-Signal Model**: Each inverter can be modeled as a small-signal equivalent circuit, where the supply current depends on the small-signal resistance of the transistors in the inverter.\n\n### Small-Signal Resistance:\n- Each inverter contributes a small-signal resistance \\( r_o \\) (output resistance of the transistors) to the supply node.\n- Since the inverters are connected in parallel at the supply node, the equivalent resistance \\( R_X \\) is the parallel combination of the small-signal resistances of the three inverters.\n\nThe equivalent resistance is given by:\n\\[\nR_X = \\frac{r_o}{3}\n\\]\nwhere \\( r_o \\) is the small-signal output resistance of a single inverter.\n\n### Conclusion:\nThe small-signal resistance seen looking into the supply node of the ring oscillator is \\( R_X = \\frac{r_o}{3} \\), where \\( r_o \\) is the output resistance of one inverter.",
        "format": "markdown",
        "sha256": "cbce52592d3cf0a3bca49854f35774bd5c70e462f0c0e4c274fd1d2b5d2a35ca"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It incorrectly treats the transistor output resistances as three parallel paths from the supply and gives no valid basis for that model. It misses the dominant oscillation-driven charging and discharging of the load capacitances.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1132,
        "output_tokens": 266,
        "total_tokens": 1398,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1132,
        "output_tokens": 266,
        "total_tokens": 1398,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the answer changes if the circuit oscillates.\n\nWhen the circuit oscillates, the inverters are no longer in a static operating point where they can be modeled as two diode-connected devices in series. Instead, the transistors in the inverters are switching dynamically, and their behavior depends on the time-varying voltages and currents in the circuit. This dynamic behavior introduces additional complexities, such as capacitive effects and time-dependent changes in the effective resistance.\n\nIn the oscillating state, the small-signal resistance \\( R_X \\) seen at the supply node is influenced by the switching activity of the inverters, which causes the current drawn from the supply to vary periodically. The effective resistance \\( R_X \\) in this case would need to account for the average or dynamic impedance of the circuit during oscillation, which is generally different from the static resistance derived under the assumption of diode-connected devices.\n\nThus, the expression \\( R_X \\approx \\frac{1}{3} \\left( \\frac{1}{g_{mn}} + \\frac{1}{g_{mp}} \\right) \\) is valid only for the static case and does not hold when the circuit is oscillating.",
        "format": "markdown",
        "sha256": "1da74257cd8f891ff7092405e7e335b5d44cb2ca51f35780479aba9879e262e0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer only says that oscillation invalidates the static model and introduces generic dynamic effects. It misses the key result that capacitor charging and discharging set RX while keeping it on the order of the MOS on-resistance, not much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1212,
        "output_tokens": 243,
        "total_tokens": 1455,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1212,
        "output_tokens": 243,
        "total_tokens": 1455,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the answer changes if the circuit oscillates.\n\nWhen the circuit oscillates, the inverters are no longer in a static operating point where they can be modeled as two diode-connected devices in series. Instead, the transistors in the inverters are switching dynamically, and their behavior depends on the time-varying voltages and currents in the circuit. This dynamic behavior introduces additional complexities, such as capacitive effects and time-dependent changes in the effective resistance.\n\nIn the oscillating state, the small-signal resistance \\( R_X \\) seen at the supply node is influenced by the switching activity of the inverters, which causes the current drawn from the supply to vary periodically. The effective resistance \\( R_X \\) in this case would need to account for the average or dynamic impedance of the circuit during oscillation, which is generally different from the static resistance derived under the assumption of diode-connected devices.\n\nThus, the expression \\( R_X \\approx \\frac{1}{3} \\left( \\frac{1}{g_{mn}} + \\frac{1}{g_{mp}} \\right) \\) is valid only for the static case and does not hold when the circuit is oscillating.",
        "format": "markdown",
        "sha256": "1da74257cd8f891ff7092405e7e335b5d44cb2ca51f35780479aba9879e262e0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer only says that oscillation invalidates the static model and introduces generic dynamic effects. It misses the key result that capacitor charging and discharging set RX while keeping it on the order of the MOS on-resistance, not much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1212,
        "output_tokens": 243,
        "total_tokens": 1455,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1212,
        "output_tokens": 243,
        "total_tokens": 1455,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the answer changes if the circuit oscillates.\n\nWhen the circuit oscillates, the inverters are no longer in a static operating point, and their behavior becomes dynamic. The small-signal resistance \\( R_X \\) seen at the supply node depends on the time-varying behavior of the transistors in the inverters. During oscillation, the transistors are switching between their on and off states, and the effective resistance seen at the supply node will vary with time.\n\nThe original computation of \\( R_X \\) assumes a static operating point where each inverter behaves as two diode-connected devices in series. This assumption is valid only when the circuit is not oscillating. During oscillation, the dynamic behavior of the circuit must be considered, and the effective resistance \\( R_X \\) will no longer be accurately described by the static formula:\n\n\\[\nR_X \\approx \\frac{1}{3} \\left( \\frac{1}{g_{mn}} + \\frac{1}{g_{mp}} \\right).\n\\]\n\nInstead, the dynamic impedance at the supply node would need to be analyzed, taking into account the time-varying currents and voltages in the circuit. This requires a more detailed analysis of the oscillatory behavior of the ring oscillator.",
        "format": "markdown",
        "sha256": "ef65ba52aa467f7b7df99beed91f21318dad8643762fd90237ebe8b4bc4cb33f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that the static small-signal model is insufficient during oscillation, but omits the capacitive charging mechanism and whether RX remains on the order of the MOS on-resistance.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1212,
        "output_tokens": 257,
        "total_tokens": 1469,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1212,
        "output_tokens": 257,
        "total_tokens": 1469,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, M7 acts as a current source transistor, providing the tail current for the differential pair (M1 and M2). The width of M7 directly affects its transconductance (\\(g_{m7}\\)) and output resistance (\\(r_{o7}\\)), which in turn influence the initial voltage gain of the circuit.\n\n### Key Points:\n1. **Voltage Gain of the Differential Pair**:\n   The voltage gain (\\(A_v\\)) of the differential pair is approximately:\n   \\[\n   A_v = g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\(g_{m1}\\) is the transconductance of M1 (or M2).\n   - \\(R_{out}\\) is the effective output resistance seen at the drain of M1 or M2.\n\n2. **Effect of M7 on \\(R_{out}\\)**:\n   The effective output resistance \\(R_{out}\\) is influenced by the output resistance of M7 (\\(r_{o7}\\)), as it is in parallel with the output resistance of the load transistors (M3 and M4). Increasing the width of M7 reduces \\(r_{o7}\\) because:\n   \\[\n   r_{o7} = \\frac{1}{\\lambda I_{D7}}\n   \\]\n   where \\(\\lambda\\) is the channel-length modulation parameter, and \\(I_{D7}\\) is the drain current of M7. A wider M7 increases \\(I_{D7}\\), reducing \\(r_{o7}\\).\n\n3. **Impact on Voltage Gain**:\n   A reduction in \\(r_{o7}\\) decreases the overall \\(R_{out}\\), which reduces the voltage gain \\(A_v\\). Therefore, as the width of M7 increases, the initial voltage gain of the circuit decreases.\n\n### Conclusion:\nIncreasing the width of M7 decreases the initial voltage gain of the circuit due to the reduction in the effective output resistance.",
        "format": "markdown",
        "sha256": "38cf246a23ca765b56b444e22aa7240f11e01d3ae4b74f94b43a757bd4c977bf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The trend is correct, and the answer notes that a wider M7 increases tail current. But it attributes the gain decrease to M7’s output resistance loading the outputs, rather than the initial integration gain falling as tail current increases and gm/ICM decreases.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 414,
        "total_tokens": 1549,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 414,
        "total_tokens": 1549,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, M7 acts as a current source transistor, providing the tail current for the differential pair (M1 and M2). The width of M7 directly affects its transconductance (\\(g_{m7}\\)) and output resistance (\\(r_{o7}\\)).\n\n### Effect of Increasing the Width of M7:\n1. **Transconductance (\\(g_{m7}\\))**:\n   - The transconductance of M7 increases as its width increases because \\(g_{m7} \\propto \\sqrt{W/L}\\), where \\(W\\) is the width and \\(L\\) is the length of the transistor.\n   - A higher \\(g_{m7}\\) means M7 can source more current for a given gate overdrive voltage.\n\n2. **Output Resistance (\\(r_{o7}\\))**:\n   - The output resistance of M7 decreases as its width increases because \\(r_{o7} \\propto 1/I_{D}\\), and the drain current (\\(I_{D}\\)) increases with width.\n\n3. **Voltage Gain**:\n   - The initial voltage gain of the circuit is approximately proportional to the product of the transconductance of the differential pair (\\(g_{m1,2}\\)) and the output resistance of the circuit.\n   - The output resistance of the circuit is influenced by \\(r_{o7}\\), which decreases as the width of M7 increases.\n   - As \\(r_{o7}\\) decreases, the overall output resistance of the circuit decreases, reducing the voltage gain.\n\n### Conclusion:\nAs the width of M7 increases, the initial voltage gain of the circuit decreases due to the reduction in the output resistance contributed by M7.",
        "format": "markdown",
        "sha256": "796004fdb3d4c16eff72d4a06f28a9890016fd62617bc8e86da3bc585943289f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The trend is correct, and the answer recognizes that M7 is the tail device and its current rises with width. But it attributes the gain reduction to M7’s output resistance rather than the dominant initial integration-gain dependence on the input-pair transconductance relative to tail current.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 358,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 358,
        "total_tokens": 1493,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, M7 acts as a current source transistor, providing the tail current for the differential pair (M1 and M2). The width of M7 directly affects its transconductance (\\(g_{m7}\\)) and output resistance (\\(r_{o7}\\)), which in turn influence the initial voltage gain of the circuit.\n\n### Key Points:\n1. **Voltage Gain of the Differential Pair**:\n   The voltage gain (\\(A_v\\)) of the differential pair is approximately:\n   \\[\n   A_v = g_{m1} \\cdot R_{out}\n   \\]\n   where:\n   - \\(g_{m1}\\) is the transconductance of M1 (or M2).\n   - \\(R_{out}\\) is the effective output resistance seen at the drain of M1/M2, which depends on the output resistance of M7 and the load transistors (M3, M4).\n\n2. **Effect of Increasing the Width of M7**:\n   - Increasing the width of M7 increases its transconductance (\\(g_{m7}\\)) and decreases its output resistance (\\(r_{o7}\\)).\n   - A lower \\(r_{o7}\\) reduces the effective output resistance (\\(R_{out}\\)) of the circuit because \\(R_{out}\\) is determined by the parallel combination of \\(r_{o7}\\) and the output resistances of M3 and M4.\n\n3. **Impact on Voltage Gain**:\n   - Since \\(R_{out}\\) decreases with a wider M7, the overall voltage gain (\\(A_v\\)) decreases.\n   - Therefore, increasing the width of M7 reduces the initial voltage gain of the circuit.\n\n### Conclusion:\nAs the width of M7 increases, the initial voltage gain of the circuit decreases due to the reduction in the effective output resistance.",
        "format": "markdown",
        "sha256": "d59865c265a9d83c10787d8559d8eb1ed9e976bcbd9725164bbc8004610a8b99"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The answer gives the correct decreasing trend and recognizes M7 as the tail device, but attributes the change to a supposed reduction in output resistance from M7 loading the outputs. The key mechanism is increased tail current, which reduces the initial gain factor such as gm/ICM; the offered explanation is materially wrong.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1135,
        "output_tokens": 385,
        "total_tokens": 1520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1135,
        "output_tokens": 385,
        "total_tokens": 1520,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, increasing the capacitance at nodes \\( P \\) and \\( Q \\) will affect the initial voltage gain as follows:\n\n1. **Impact on Gain Bandwidth Product**: The capacitance at nodes \\( P \\) and \\( Q \\) contributes to the parasitic capacitance at these nodes. Increasing this capacitance will reduce the bandwidth of the circuit due to the increased RC time constant. However, the low-frequency gain (initial voltage gain) is not directly affected by this.\n\n2. **Impact on Gain**: The initial voltage gain is determined by the transconductance (\\( g_m \\)) of the transistors and the load impedance. If the increased capacitance does not significantly affect the operating point of the transistors or the load impedance, the initial voltage gain will remain largely unchanged.\n\n3. **Transient Behavior**: While the initial voltage gain may not change significantly, the increased capacitance will slow down the transient response of the circuit, as it takes longer to charge or discharge the larger capacitance.\n\nIn summary, increasing the capacitance at nodes \\( P \\) and \\( Q \\) will not significantly affect the initial voltage gain but will reduce the bandwidth and slow down the transient response of the circuit.",
        "format": "markdown",
        "sha256": "7929f9170fe393ab0b21b18ee808270487441ffb3c7b4a0a560712bed2611a08"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that the initial gain remains essentially unchanged and that larger capacitance slows the transient. However, it explains this using a generic low-frequency gain and load-impedance argument rather than the relevant dynamic gain, where the longer amplification interval cancels the reduced voltage slope.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 251,
        "total_tokens": 1386,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 251,
        "total_tokens": 1386,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, increasing the capacitance at nodes **P** and **Q** will affect the initial voltage gain as follows:\n\n1. **Impact on Gain Bandwidth Product**: The capacitance at nodes **P** and **Q** contributes to the parasitic capacitance at these nodes. Increasing this capacitance will reduce the bandwidth of the circuit due to the increased RC time constant. However, the low-frequency gain (initial voltage gain) is not directly affected by this capacitance.\n\n2. **Impact on Gain**: The initial voltage gain is primarily determined by the transconductance (\\(g_m\\)) of the transistors and the load impedance. The increased capacitance at **P** and **Q** does not directly affect the transconductance or the load impedance at low frequencies. Therefore, the initial voltage gain remains largely unchanged.\n\n3. **Transient Behavior**: While the initial voltage gain remains unaffected, the increased capacitance will slow down the transient response of the circuit, as it takes longer to charge or discharge the larger capacitance.\n\n### Conclusion:\nThe **initial voltage gain** of the circuit will **not change significantly** if the capacitance at nodes **P** and **Q** is increased. However, the circuit's bandwidth and transient response will be adversely affected.",
        "format": "markdown",
        "sha256": "1cb52d6c08f753c056363ebc3c7543bad59738dc812ffa9ec7498560beae1876"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The conclusion that the initial gain remains unchanged is correct, and the answer correctly notes that larger capacitance slows the transient. But it treats the gain as a low-frequency gm/load-impedance gain; the relevant reason is that capacitance slows the discharge while proportionally extending the amplification phase, so its effect cancels.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1135,
        "output_tokens": 263,
        "total_tokens": 1398,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1135,
        "output_tokens": 263,
        "total_tokens": 1398,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the given circuit, increasing the capacitance at nodes \\( P \\) and \\( Q \\) will affect the initial voltage gain as follows:\n\n1. **Impact on Gain Bandwidth Product**: The capacitance at nodes \\( P \\) and \\( Q \\) contributes to the parasitic capacitance at these nodes. Increasing this capacitance will reduce the bandwidth of the circuit due to the increased RC time constant. However, the low-frequency gain (initial voltage gain) is not directly affected by this.\n\n2. **Impact on Gain**: The initial voltage gain is primarily determined by the transconductance (\\( g_m \\)) of the transistors and the load impedance. If the increased capacitance does not significantly affect the operating point of the transistors or the load impedance, the initial voltage gain will remain largely unchanged.\n\n3. **Transient Behavior**: While the initial voltage gain may not change significantly, the increased capacitance will slow down the transient response of the circuit, as it takes longer to charge or discharge the larger capacitance.\n\nIn summary, increasing the capacitance at nodes \\( P \\) and \\( Q \\) will not significantly affect the initial voltage gain but will reduce the bandwidth and slow down the transient response of the circuit.",
        "format": "markdown",
        "sha256": "fff172a3f7b41c611935d0917afdc8de890b1239a4f5803c0bb1e4fade38313d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that the initial gain remains essentially unchanged and that the transient slows, but attributes this to low-frequency gain being set by transconductance and load impedance. The key reason is that the larger capacitance lengthens the amplification interval proportionally, canceling its effect on the accumulated gain.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 252,
        "total_tokens": 1387,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1135,
        "output_tokens": 252,
        "total_tokens": 1387,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of M5 and M6 in the circuit will generally improve the speed of the circuit. Here's why:\n\n1. **Reduced Resistance**: Increasing the widths of M5 and M6 reduces their on-resistance (\\(R_{on}\\)), allowing them to charge and discharge the nodes \\(X\\) and \\(Y\\) more quickly.\n\n2. **Improved Drive Strength**: Wider transistors have higher drive strength, which means they can source or sink more current. This helps in faster charging and discharging of the parasitic capacitances at nodes \\(X\\) and \\(Y\\).\n\n3. **Impact on Speed**: The speed of the circuit is often limited by the RC time constant (\\(R_{on} \\cdot C\\)) at critical nodes. By reducing \\(R_{on}\\), the RC time constant decreases, leading to faster transitions and improved speed.\n\nHowever, there are trade-offs to consider:\n- **Increased Capacitance**: Wider transistors also increase parasitic capacitances, which can partially offset the speed improvement.\n- **Power Consumption**: Wider transistors consume more power due to increased leakage and dynamic power.\n\nIn summary, increasing the widths of M5 and M6 generally improves the speed of the circuit, but the trade-offs in power and capacitance should be carefully evaluated.",
        "format": "markdown",
        "sha256": "ff326703e81c6e3301e74acf6ffa5acc453cddf54b7c6fa672f58709f337cd12"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It gets the initial trend right and notes that wider devices add capacitance, but it does not identify M5/M6’s regenerative role or explain that the capacitance eventually limits the benefit and creates an optimum width.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 273,
        "total_tokens": 1407,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 273,
        "total_tokens": 1407,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of transistors M5 and M6 in the circuit will generally improve the speed of the circuit. Here's why:\n\n1. **Reduced Resistance**: Increasing the width of M5 and M6 reduces their on-resistance (\\(R_{on}\\)), allowing them to charge and discharge the nodes \\(X\\) and \\(Y\\) more quickly.\n\n2. **Improved Current Drive**: Wider transistors can drive more current, which helps in faster charging and discharging of the parasitic capacitances at nodes \\(X\\) and \\(Y\\).\n\n3. **Impact on Speed**: Since the speed of the circuit is often limited by the RC time constant (\\(R_{on} \\cdot C\\)), reducing \\(R_{on}\\) by increasing the width of M5 and M6 decreases the time constant, thereby improving the speed.\n\nHowever, there are trade-offs to consider:\n- **Increased Capacitance**: Wider transistors also increase the parasitic capacitance at nodes \\(X\\) and \\(Y\\), which could partially offset the speed improvement.\n- **Power Consumption**: Wider transistors consume more power due to increased leakage and dynamic power.\n\nIn summary, increasing the widths of M5 and M6 generally improves the speed of the circuit, but the trade-offs in power and capacitance should be carefully evaluated.",
        "format": "markdown",
        "sha256": "4872a3b263239422934e3cf2597ca81a5fecc625f0ea39a5ed8709973045786f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly predicts an initial speed improvement and notes that added capacitance can offset it. However, it does not explain the stronger regenerative action of the cross-coupled PMOS devices or state that the benefit eventually diminishes and may reverse beyond an optimum width.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 278,
        "total_tokens": 1412,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 278,
        "total_tokens": 1412,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Increasing the widths of M5 and M6 in the circuit will generally improve the speed of the circuit. Here's why:\n\n1. **Reduced Resistance**: Increasing the widths of M5 and M6 reduces their on-resistance (\\(R_{on}\\)), allowing them to charge and discharge the nodes \\(X\\) and \\(Y\\) more quickly.\n\n2. **Improved Drive Strength**: Wider transistors have higher drive strength, which means they can source or sink more current. This helps in faster charging and discharging of the parasitic capacitances at nodes \\(X\\) and \\(Y\\).\n\n3. **Impact on Speed**: The reduced resistance and increased drive strength lead to a reduction in the RC time constant (\\(R_{on} \\cdot C\\)), which directly improves the speed of the circuit.\n\nHowever, there are trade-offs to consider:\n- **Increased Capacitance**: Wider transistors also increase the parasitic capacitance at nodes \\(X\\) and \\(Y\\). If the increase in capacitance outweighs the reduction in resistance, the speed improvement may be limited.\n- **Power Consumption**: Wider transistors consume more power due to increased leakage and dynamic power dissipation.\n\nIn summary, increasing the widths of M5 and M6 generally improves the speed of the circuit, but the extent of improvement depends on the balance between reduced resistance and increased capacitance.",
        "format": "markdown",
        "sha256": "6888131ec389edecfea245bbee35bdeee6ad6e9951c4be63a97cc5f5dcd56655"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Gets the main trend right and notes that added capacitance can limit the benefit. However, it gives a generic resistance/RC explanation rather than identifying M5/M6’s regenerative pull-up role, and does not clearly state that the improvement is initial or reaches an optimum.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 287,
        "total_tokens": 1421,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1134,
        "output_tokens": 287,
        "total_tokens": 1421,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) has the following effects:\n\n1. **Improved Drive Strength**: Increasing the transistor widths reduces their on-resistance (\\( R_{on} \\)), allowing them to charge or discharge the nodes \\( X \\) and \\( Y \\) more quickly. This can improve the speed of the circuit.\n\n2. **Increased Capacitance**: Wider transistors also increase the parasitic capacitance at the nodes they are connected to. This added capacitance can slow down the circuit because it takes more time to charge or discharge the larger capacitance.\n\n### Net Effect:\n- If the improvement in drive strength outweighs the increase in capacitance, the circuit speed improves.\n- If the increase in capacitance dominates, the circuit speed degrades.\n\nIn practice, there is an optimal transistor width that balances these effects. Beyond a certain point, increasing the widths further will degrade the speed due to excessive parasitic capacitance.",
        "format": "markdown",
        "sha256": "25124cb513a416ffd6c6b5d4f1bbdd266dcdb54c9ff5f9c91249a7ddd00ae605"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly identifies the lower on-resistance benefit, added node capacitance, and an eventual optimum, but presents the speed improvement as conditional rather than clearly stating that widening initially improves speed.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 220,
        "total_tokens": 1018,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 220,
        "total_tokens": 1018,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) has the following effects:\n\n1. **Improved Drive Strength**: Increasing the transistor widths reduces their on-resistance (\\( R_{on} \\)), allowing them to charge or discharge the nodes \\( X \\) and \\( Y \\) more quickly. This can improve the speed of the circuit by reducing the delay associated with charging and discharging these nodes.\n\n2. **Increased Capacitance**: However, increasing the widths also increases the parasitic capacitance of the transistors (gate, drain, and source capacitances). This added capacitance can slow down the circuit because it takes more time to charge or discharge the larger capacitance.\n\n### Net Effect:\n- If the increase in drive strength outweighs the increase in parasitic capacitance, the circuit speed improves.\n- If the increase in parasitic capacitance dominates, the circuit speed degrades.\n\nIn practice, there is an optimal transistor width that balances these two effects. Beyond this optimal point, further increasing the widths will degrade the speed due to excessive parasitic capacitance.",
        "format": "markdown",
        "sha256": "66f53f028727397abd2c9d14dd3f18c739d6feba5bdf031311ad0423b7438e6d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly identifies the lower on-resistance, added capacitance, and an optimum beyond which speed degrades. However, it makes the net trend conditional rather than clearly stating the required initial speed improvement as width increases.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 245,
        "total_tokens": 1043,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 245,
        "total_tokens": 1043,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) has the following effects:\n\n1. **Improved Drive Strength**: Increasing the transistor widths reduces their on-resistance (\\( R_{on} \\)), allowing them to charge or discharge the nodes \\( X \\) and \\( Y \\) more quickly. This can improve the speed of the circuit by reducing the delay associated with charging and discharging these nodes.\n\n2. **Increased Capacitance**: Wider transistors also increase the parasitic capacitance at the nodes they are connected to. This increased capacitance can slow down the circuit because it takes more time to charge or discharge larger capacitances.\n\n### Net Effect:\n- If the improvement in drive strength outweighs the increase in capacitance, the circuit speed improves.\n- If the increase in capacitance dominates, the circuit speed degrades.\n\nIn practice, there is an optimal transistor width that balances these two effects. Beyond this optimal width, further increasing the transistor size may degrade the speed due to excessive parasitic capacitance.",
        "format": "markdown",
        "sha256": "187d9e84922cc75a34cb9a0f0ee9bd88070091cdfde054cf3925dab1cb61552b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It identifies the resistance reduction, added capacitance, and an optimum, but leaves the effect conditional instead of stating the key trend that widening initially improves speed.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 233,
        "total_tokens": 1031,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 233,
        "total_tokens": 1031,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the structure in the figure does not provide quadrature outputs. Quadrature outputs refer to two signals that are 90 degrees out of phase with each other. The circuit shown appears to be a dynamic logic circuit, possibly a clocked latch or a similar structure, but it does not inherently generate quadrature signals.",
        "format": "markdown",
        "sha256": "e29ba73f28e36c6ebe465977f6214970bdefe02cd0ecfaac481c957aff1e8b7b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The conclusion is wrong: the divide-by-two structure provides nominal quadrature outputs. The answer only gives a generic definition of quadrature and does not identify the latch timing that produces it.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 64,
        "total_tokens": 847,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 64,
        "total_tokens": 847,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the structure in the figure does not provide quadrature outputs. Quadrature outputs refer to two signals that are 90 degrees out of phase with each other. The circuit shown appears to be a dynamic logic circuit, possibly a clocked latch or a similar structure, but it does not inherently generate quadrature signals. Quadrature signals are typically generated using specific oscillator or phase-shifting circuits, such as quadrature oscillators or mixers.",
        "format": "markdown",
        "sha256": "f26bdbbcba3dcc1a64aa6f8c7397b0f0177fbc4476dd365025ba0366e13bfbaf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer incorrectly rejects quadrature and misses the C2MOS divide-by-two operation, whose opposite-phase latches switch half an output period apart. It gives no relevant account of the actual timing or loading effects.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 88,
        "total_tokens": 871,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 88,
        "total_tokens": 871,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "No, the structure in the figure does not provide quadrature outputs. Quadrature outputs refer to two signals that are 90 degrees out of phase with each other. The circuit shown appears to be a dynamic logic circuit, possibly a clocked latch or a similar structure, but it does not inherently generate quadrature signals. Quadrature signals are typically generated using specific oscillator or phase-shifting circuits, such as quadrature oscillators or mixers.",
        "format": "markdown",
        "sha256": "f26bdbbcba3dcc1a64aa6f8c7397b0f0177fbc4476dd365025ba0366e13bfbaf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer incorrectly rejects quadrature and misses the C2MOS divide-by-two operation, whose opposite-phase latches switch half an output period apart. It gives no relevant account of the actual timing or loading effects.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 88,
        "total_tokens": 871,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 783,
        "output_tokens": 88,
        "total_tokens": 871,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) will generally **improve the speed** of the circuit. Here's why:\n\n1. **Increased Drive Strength**: Wider transistors have lower on-resistance (\\( R_{on} \\)), which allows them to charge or discharge the capacitive nodes faster. This reduces the propagation delay of the circuit.\n\n2. **Reduced RC Delay**: The RC delay at the nodes is proportional to the resistance of the transistors and the capacitance of the nodes. By increasing the transistor widths, the resistance decreases, leading to a reduction in the RC delay.\n\nHowever, there are trade-offs to consider:\n\n- **Increased Capacitance**: Wider transistors also have higher gate and diffusion capacitances, which can increase the load on the preceding stage and potentially slow down the overall circuit if not properly managed.\n- **Power Consumption**: Wider transistors consume more dynamic power due to increased capacitance and leakage power due to larger device sizes.\n\nIn summary, increasing the widths of the clocked transistors will improve the speed of the circuit up to a certain point, but the benefits may diminish if the increased capacitance starts to dominate or if power consumption becomes a concern.",
        "format": "markdown",
        "sha256": "61ebd1b25fd78ec6f9d8fb16db3b0d46885e80a4cdf5fab8c8c9d769bb10e6cf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that wider clocked transistors improve speed because their lower on-resistance reduces delay. It omits the key charge-sharing limitation and gives a generic capacitance caveat rather than explaining that the added capacitance is largely off the data path.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 271,
        "total_tokens": 1069,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 271,
        "total_tokens": 1069,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) will have the following effects:\n\n1. **Improved Drive Strength**: Increasing the transistor widths reduces their on-resistance, allowing them to charge or discharge the nodes faster. This can improve the speed of the circuit by reducing the delay associated with switching.\n\n2. **Increased Capacitance**: Wider transistors also increase the parasitic capacitance at the nodes they are connected to. This increased capacitance can slow down the circuit because it takes more time to charge or discharge the larger capacitance.\n\n### Net Effect:\n- If the increase in drive strength outweighs the increase in parasitic capacitance, the circuit speed will improve.\n- If the increase in parasitic capacitance dominates, the circuit speed will degrade.\n\nIn most cases, there is an optimal transistor width that balances these effects. Beyond this optimal point, further increasing the widths of the clocked transistors may degrade the speed due to excessive parasitic capacitance.",
        "format": "markdown",
        "sha256": "0dae7d43cb048cb2b11e1ee60329b21323f69b763f2ca6b664f635ae953791c1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly notes that wider clocked devices lower on-resistance, but hedges the speed trend and treats added capacitance as a generic competing load. It misses that these devices add little loading to the data path and omits charge sharing as the swing-limiting effect.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 223,
        "total_tokens": 1021,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 223,
        "total_tokens": 1021,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "In the circuit shown, increasing the widths of the clocked transistors (those controlled by the clock signals \\( CK \\) and \\( \\overline{CK} \\)) will generally **improve the speed** of the circuit. Here's why:\n\n1. **Increased Drive Strength**: Wider transistors have lower on-resistance (\\( R_{on} \\)), which allows them to charge or discharge the capacitive nodes faster. This reduces the propagation delay of the circuit.\n\n2. **Reduced RC Delay**: The RC delay at the nodes is reduced because the resistance of the clocked transistors decreases with increased width, even though the capacitance increases slightly due to the larger gate area.\n\nHowever, there are trade-offs to consider:\n\n- **Increased Capacitance**: While wider transistors reduce resistance, they also increase parasitic capacitance (gate, drain, and source capacitances). This can slightly offset the speed improvement, especially in circuits with high fan-out or heavily loaded nodes.\n\n- **Power Consumption**: Wider transistors consume more dynamic power due to increased capacitance and leakage power due to larger transistor sizes.\n\nIn summary, increasing the widths of the clocked transistors will improve the speed of the circuit, but the improvement comes at the cost of increased power consumption and potentially higher area. The decision to increase widths should balance speed requirements with power and area constraints.",
        "format": "markdown",
        "sha256": "e2a7a4819bcd3b13d605de22918f5d57b238956fd487fd12889a40891e2ccfb1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that widening the clocked transistors improves speed and cites their lower on-resistance. It omits the key topology-specific point that their added capacitance is largely off the data path and does not mention charge sharing as a limit.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 281,
        "total_tokens": 1079,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 798,
        "output_tokens": 281,
        "total_tokens": 1079,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure represents a **ring oscillator** circuit. Here's the analysis of the arrangement:\n\n1. **Components**:\n   - The circuit consists of a series of inverters (logic NOT gates) connected in a loop.\n   - There are switches labeled `CK` and `\\(\\overline{CK}\\)` that control the operation of the circuit.\n   - The inverters are connected in a feedback loop, with the output of the last inverter fed back to the input of the first.\n\n2. **Operation**:\n   - When the switches are appropriately configured, the circuit oscillates between high and low logic levels.\n   - The oscillation is due to the propagation delay of the inverters. The signal takes time to travel through each inverter, and the feedback loop ensures continuous toggling.\n   - The frequency of oscillation depends on the number of inverters and their propagation delays.\n\n3. **Purpose**:\n   - Ring oscillators are commonly used in integrated circuits for testing and measuring propagation delays, generating clock signals, or as random number generators.\n\n4. **Control**:\n   - The switches `CK` and `\\(\\overline{CK}\\)` can be used to enable or disable the oscillation. For example:\n     - When `CK` is closed, the circuit is active.\n     - When `\\(\\overline{CK}\\)` is closed, the circuit may be disabled or reset.\n\nThis circuit is a fundamental building block in digital electronics and is widely used in various applications.",
        "format": "markdown",
        "sha256": "5e7bc8e0b6a564d77c0ec81b63b1c9faac174317f4979c4fab1c07a3639360ac"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the circuit as a ring oscillator. The figure is a divide-by-two circuit built from dynamic latches, and the answer misses its essential operation.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 305,
        "total_tokens": 1424,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 305,
        "total_tokens": 1424,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure represents a **ring oscillator** circuit. Here's the analysis of the arrangement:\n\n1. **Components**:\n   - The circuit consists of a series of inverters (logic NOT gates) connected in a loop.\n   - There are switches controlled by clock signals \\( CK \\) and \\( \\overline{CK} \\) (complement of \\( CK \\)).\n   - The inverters are labeled \\( Inv_1 \\), and subsequent inverters are unnamed but follow the same logic.\n\n2. **Operation**:\n   - The switches \\( CK \\) and \\( \\overline{CK} \\) control the flow of the signal through the circuit.\n   - When \\( CK \\) is active (closed), the signal propagates through the first inverter \\( Inv_1 \\).\n   - The output of \\( Inv_1 \\) is inverted and passed to the next stage, and so on, through the chain of inverters.\n   - The feedback loop ensures that the signal continuously oscillates between high and low states.\n\n3. **Oscillation**:\n   - The circuit relies on the propagation delay of the inverters to generate oscillations.\n   - The total delay of the circuit determines the frequency of oscillation.\n   - The feedback loop ensures that the signal keeps toggling, creating a periodic waveform.\n\n4. **Applications**:\n   - Ring oscillators are commonly used in clock generation, frequency synthesis, and testing the performance of integrated circuits (e.g., measuring propagation delay).\n\n5. **Key Characteristics**:\n   - The circuit oscillates only if the number of inverters is odd. This ensures that the feedback signal is inverted, creating instability and oscillation.\n   - The frequency of oscillation is inversely proportional to the total delay of the inverters in the loop.\n\nThis specific arrangement appears to be a controlled ring oscillator, where the switches \\( CK \\) and \\( \\overline{CK} \\) can enable or disable the oscillation.",
        "format": "markdown",
        "sha256": "2effa985f2de618152cfbbc2c4811771133cc75e4457c09d2692c1ba774e1636"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the dynamic-latch divide-by-two as a ring oscillator and incorrectly claims it free-runs based on inverter delay. It misses the intended half-frequency division.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 400,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 400,
        "total_tokens": 1519,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The figure represents a **ring oscillator** circuit. Here's the analysis of the arrangement:\n\n1. **Components**:\n   - The circuit consists of a series of inverters (logic NOT gates) connected in a loop.\n   - There are switches controlled by clock signals \\( CK \\) and \\( \\overline{CK} \\) (complement of \\( CK \\)).\n   - The inverters are labeled \\( Inv_1 \\), and subsequent inverters are unnamed but follow the same logic.\n\n2. **Operation**:\n   - The switches \\( CK \\) and \\( \\overline{CK} \\) control the flow of the signal through the circuit.\n   - When \\( CK \\) is active (closed), the signal propagates through the first inverter \\( Inv_1 \\).\n   - The output of \\( Inv_1 \\) is inverted and passed to the next stage, and so on, through the chain of inverters.\n   - The feedback loop ensures that the signal continuously oscillates between high and low states.\n\n3. **Oscillation**:\n   - The circuit relies on the propagation delay of the inverters to generate oscillations.\n   - The total delay of the circuit is determined by the number of inverters and their individual propagation delays.\n   - The frequency of oscillation is inversely proportional to the total delay.\n\n4. **Purpose**:\n   - Ring oscillators are commonly used in integrated circuits for testing and measurement purposes, such as determining the delay of logic gates or generating clock signals.\n\n5. **Key Characteristics**:\n   - The circuit requires an odd number of inverters to ensure oscillation.\n   - The switches \\( CK \\) and \\( \\overline{CK} \\) can be used to enable or disable the oscillation.\n\nThis specific arrangement is a controlled ring oscillator, where the clock signals \\( CK \\) and \\( \\overline{CK} \\) can be used to start or stop the oscillation.",
        "format": "markdown",
        "sha256": "6a320fd5294622c6797fcd08a1880b4ed4f70402aed079ba5a78c7ab5a6eacd8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The circuit is a dynamic-latch divide-by-two, not a ring oscillator; the answer misidentifies its topology, operation, and function.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 398,
        "total_tokens": 1517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1119,
        "output_tokens": 398,
        "total_tokens": 1517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter in the figure is part of a feedback loop, and its inclusion affects the performance of the circuit in the following ways:\n\n1. **Inversion of Signal**: The red inverter inverts the signal, which can introduce a phase shift in the feedback loop. This phase shift is critical in determining the behavior of the circuit, such as whether it oscillates or stabilizes.\n\n2. **Feedback Control**: The red inverter creates a feedback path that can influence the timing and stability of the circuit. Depending on the design, this feedback can either stabilize the circuit or cause oscillations.\n\n3. **Delay Addition**: The inverter adds a propagation delay to the feedback loop. This delay can affect the overall timing of the circuit, potentially impacting its speed and performance.\n\n4. **Signal Conditioning**: The inverter ensures that the feedback signal is properly conditioned (e.g., inverted) to meet the requirements of the circuit's logic design.\n\nIn summary, the red inverter plays a crucial role in shaping the behavior of the circuit by introducing inversion, delay, and feedback control. Its impact on performance depends on the specific application and design goals of the circuit.",
        "format": "markdown",
        "sha256": "e09490cabe33459547fe880992ba6616852e5cebf97b49150b845b84410649a4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives only generic feedback, delay, and oscillation comments. It misses the red inverter’s feedforward path that bypasses part of the first latch and speeds operation, as well as the key low-frequency drawback that raises the minimum usable clock frequency.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 233,
        "total_tokens": 1357,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 233,
        "total_tokens": 1357,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter in the figure is part of a feedback loop, and its inclusion affects the performance of the circuit in the following ways:\n\n1. **Signal Inversion**: The red inverter inverts the signal, which can be used to create a complementary signal or to ensure proper logic levels in the circuit. This is particularly useful in clocking circuits or flip-flops where complementary clock signals are needed.\n\n2. **Delay Introduction**: The red inverter introduces a propagation delay. This delay can affect the timing of the circuit, potentially impacting the overall speed and synchronization of the system.\n\n3. **Stability and Oscillation**: If the feedback loop is improperly designed, the red inverter could contribute to instability or oscillation in the circuit. Proper design ensures that the feedback loop operates as intended without causing unwanted behavior.\n\n4. **Power Consumption**: The addition of the red inverter increases the power consumption of the circuit, as it requires additional energy to operate.\n\n5. **Signal Integrity**: The red inverter can help improve signal integrity by restoring signal levels, especially if the signal has degraded due to noise or other factors.\n\nIn summary, the red inverter plays a critical role in the circuit's functionality, but its impact on performance depends on the specific application and design considerations.",
        "format": "markdown",
        "sha256": "8e17bbc02c3fc940ab8c6d1bdfed5e33beea5f7c5416c1dbba4de55506b0ef6c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer misses the key feedforward bypass that improves high-speed operation and the unclocked branch’s low-frequency drawback, which raises the minimum usable clock frequency. Its generic mention of feedback and possible oscillation is only loosely relevant to the actual mechanism.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 256,
        "total_tokens": 1380,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 256,
        "total_tokens": 1380,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The red inverter in the figure is part of a feedback loop, and its inclusion can significantly affect the performance of the circuit. Here's how:\n\n1. **Signal Inversion and Feedback**:\n   - The red inverter introduces an additional inversion in the feedback loop. This can change the behavior of the circuit, potentially altering its stability or oscillation characteristics.\n   - If the circuit is designed as a ring oscillator, the red inverter increases the total number of inversions in the loop, which is critical for oscillation. For a ring oscillator to function, the total number of inversions in the loop must be odd.\n\n2. **Delay and Frequency**:\n   - The red inverter adds an additional propagation delay to the feedback loop. This increases the total delay of the loop, which in turn reduces the oscillation frequency of the circuit.\n   - The oscillation frequency of a ring oscillator is inversely proportional to the total delay in the loop. Adding the red inverter slows down the circuit.\n\n3. **Power Consumption**:\n   - The red inverter consumes additional power, which may slightly increase the overall power consumption of the circuit.\n\n4. **Signal Integrity**:\n   - The red inverter may also affect the signal integrity by introducing additional loading or noise into the circuit, depending on its design and placement.\n\nIn summary, the red inverter affects the performance by altering the oscillation frequency, increasing delay, and potentially impacting power consumption and signal integrity. Its inclusion must be carefully considered based on the intended functionality of the circuit.",
        "format": "markdown",
        "sha256": "3d6be4af41d5bde468b5fdf4fb873fbabb75b568b2be910117be4a59c7010b29"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer treats the red inverter as a delay-adding feedback element and predicts slower oscillation, missing the key feedforward bypass that improves high-speed operation and the unclocked branch’s low-frequency drawback. Its mention of a possible oscillating loop is only limited relevant insight.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 304,
        "total_tokens": 1428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 304,
        "total_tokens": 1428,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The answer provided is **incorrect**. The red inverter in the figure does not act as a keeper or form a cross-coupled latch with `Inv1`. Instead, its actual role is to **invert the signal** and provide feedback to the input of `Inv1`. This forms part of a **ring oscillator** circuit.\n\n### Explanation of the Circuit:\n1. The circuit shown is a **ring oscillator**, which is a common circuit used to generate a periodic clock signal.\n2. The red inverter is part of the feedback loop that connects the output of the last inverter back to the input of the first inverter (`Inv1`).\n3. The red inverter ensures that the feedback signal is inverted, maintaining the oscillation condition for the ring oscillator.\n4. The oscillation frequency depends on the number of inverters in the loop and their propagation delays.\n\n### Why the Answer is Incorrect:\n- A **keeper** is typically used to maintain the state of a node in the presence of leakage currents, often in static circuits or latches. However, this circuit is dynamic and does not rely on a keeper.\n- The red inverter does not form a cross-coupled latch with `Inv1`. A cross-coupled latch requires two inverters connected in a feedback loop to store a stable state, which is not the case here.\n\n### Actual Role of the Red Inverter:\nThe red inverter is a functional part of the feedback loop in the ring oscillator. It ensures the correct phase inversion required for oscillation. Without it, the circuit would not oscillate properly.",
        "format": "markdown",
        "sha256": "1d634c95014abaaab17ea8adecba23be9f183e498b51780db11158902c0eb631"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "Correctly rejects the keeper interpretation, but misidentifies the red inverter as feedback to Inv1 and a conventional ring-oscillator element. It misses the key feedforward path bypassing the CK switch and the high-speed/low-frequency tradeoff.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 317,
        "total_tokens": 1486,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 317,
        "total_tokens": 1486,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The answer provided is **incorrect**. The red inverter in the figure does not act as a keeper or form a cross-coupled latch with `Inv1`. Instead, its actual role is to **invert the signal** and provide feedback to the input of `Inv1`. This forms a **ring oscillator**.\n\n### Explanation of the Circuit:\n1. The circuit shown is a **ring oscillator**, which is a chain of inverters connected in a loop.\n2. The red inverter is part of the feedback loop and ensures that the signal propagates through the chain of inverters, creating oscillations.\n3. The oscillation frequency depends on the number of inverters in the loop and their propagation delay.\n\n### Why the Red Inverter is Not a Keeper:\n- A **keeper** is typically used to maintain the state of a node (e.g., in dynamic logic circuits) and prevent it from floating due to leakage. It usually involves a weak feedback mechanism.\n- In this circuit, the red inverter is not maintaining the state of the node but is actively participating in the signal inversion and propagation required for oscillation.\n\n### Summary:\nThe red inverter's role is to **invert the signal and complete the feedback loop** in the ring oscillator. It does not act as a keeper or remove any minimum clock frequency requirement.",
        "format": "markdown",
        "sha256": "a6d52f6a67689fd59b445a6851f56b60270d1c587dec3e356a44692cf543423b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly rejects the keeper interpretation and recognizes a possible ring-loop effect, but misidentifies the red inverter’s connection and misses its main feedforward role bypassing the latch path. It also omits the high-speed benefit and the low-frequency failure that raises the minimum usable clock rate.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 266,
        "total_tokens": 1435,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 266,
        "total_tokens": 1435,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The answer provided is **incorrect**. The red inverter does not act as a keeper or form a cross-coupled latch with `Inv1`. Instead, its actual role is to **invert the signal** and provide feedback to the circuit.\n\n### Explanation of the Circuit:\n1. The circuit shown is a **ring oscillator**.\n2. A ring oscillator consists of an odd number of inverters connected in a loop, with the output of the last inverter fed back to the input of the first.\n3. The red inverter is part of the feedback loop and ensures the correct phase inversion for oscillation.\n\n### Role of the Red Inverter:\n- The red inverter is **not a keeper**. A keeper is typically used to maintain a logic level in the presence of leakage or noise, often in static circuits or latches.\n- Instead, the red inverter is **essential for the oscillation** of the ring oscillator. It contributes to the odd number of inversions required for oscillation.\n\n### Minimum Clock Frequency:\n- The statement about removing the minimum clock frequency requirement due to leakage is irrelevant in this context. Ring oscillators are free-running circuits and do not rely on an external clock signal.\n\n### Conclusion:\nThe red inverter is a functional part of the ring oscillator, ensuring the correct number of inversions for oscillation. It does not act as a keeper or form a cross-coupled latch.",
        "format": "markdown",
        "sha256": "ed895614ef0f1f84ea3b59396d87bdac64ebf52592fa891986acb1019312854a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly rejects the keeper interpretation, but misidentifies the circuit as a free-running ring oscillator. The red inverter is a feedforward branch that bypasses part of the latch path; it can help at high speeds but can overpower the intended behavior at low clock rates, raising the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 283,
        "total_tokens": 1452,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1169,
        "output_tokens": 283,
        "total_tokens": 1452,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the circuit shown for noise figure (NF) while maintaining \\( R_{in} = 50 \\, \\Omega \\), the following steps can be taken:\n\n### 1. **Adjust the Transconductance (\\( g_m \\)) of \\( M_1 \\):**\n   - The input impedance \\( R_{in} \\) is determined by the feedback resistor \\( R_F \\) and the transconductance \\( g_m \\) of \\( M_1 \\):\n     \\[\n     R_{in} = \\frac{1}{g_m} \\parallel R_F\n     \\]\n   - To maintain \\( R_{in} = 50 \\, \\Omega \\), choose \\( g_m \\) such that:\n     \\[\n     g_m = \\frac{1}{R_{in}} = \\frac{1}{50} = 0.02 \\, \\text{S}\n     \\]\n   - Ensure \\( R_F \\) is large enough so that \\( R_{in} \\) is primarily determined by \\( g_m \\).\n\n### 2. **Minimize Noise Contribution from \\( R_F \\):**\n   - The feedback resistor \\( R_F \\) contributes thermal noise. To minimize its impact:\n     - Use a high \\( R_F \\) value, as long as it does not affect the stability or \\( R_{in} \\).\n     - Ensure \\( g_m \\) dominates the impedance seen at the input.\n\n### 3. **Optimize \\( M_1 \\) for Low Noise:**\n   - The noise figure is heavily influenced by the noise of \\( M_1 \\). To reduce its noise:\n     - Use a transistor with a low noise figure (e.g., a device with low flicker noise and thermal noise).\n     - Operate \\( M_1 \\) at an optimal bias point to minimize its noise contribution. This typically involves setting the drain current \\( I_D \\) to an optimal value for the given transistor.\n\n### 4. **Minimize Parasitic Capacitances:**\n   - Parasitic capacitances at the input can degrade the noise figure and input matching. To minimize their effect:\n     - Use a transistor with a small gate capacitance.\n     - Ensure proper layout techniques to reduce parasitic capacitances.\n\n### 5. **Optimize \\( M_2 \\):**\n   - \\( M_2 \\) acts as a current source. Its noise contribution should be minimized by:\n     - Using a high output impedance for \\( M_2 \\).\n     - Biasing \\( M_2 \\) properly to ensure it operates in the saturation region.\n\n### 6. **Choose \\( C_1 \\) Appropriately:**\n   - The coupling capacitor \\( C_1 \\) should be large enough to ensure it does not affect the input impedance or introduce additional noise.\n\n### 7. **Simulate and Verify:**\n   - Use circuit simulation tools to verify the noise figure and input impedance.\n   - Adjust \\( g_m \\), \\( R_F \\), and biasing conditions iteratively to achieve the desired performance.\n\nBy carefully balancing these parameters, the circuit can be optimized for a low noise figure while maintaining \\( R_{in} = 50 \\, \\Omega \\).",
        "format": "markdown",
        "sha256": "8b0349f22dcca60372628f027c4fae87eacccdab9fce5bbd19b5ca8d515a6fcd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It incorrectly treats the input resistance as approximately set by 1/gm, fixes gm at 1/50 S, and recommends making RF large. It misses the finite-output-resistance relation that allows gm and RF to increase together while holding Rin at 50 Ω and reducing NF.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 667,
        "total_tokens": 1803,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1136,
        "output_tokens": 667,
        "total_tokens": 1803,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the circuit shown for noise figure (NF) while maintaining \\( R_{in} = 50 \\, \\Omega \\), the following steps can be taken:\n\n### 1. **Adjust the Transconductance (\\( g_m \\)) of \\( M_1 \\):**\n   - The input impedance of the circuit is determined by the feedback resistor \\( R_F \\) and the transconductance \\( g_m \\) of \\( M_1 \\). Specifically:\n     \\[\n     R_{in} = \\frac{1}{g_m} \\parallel R_F\n     \\]\n   - To maintain \\( R_{in} = 50 \\, \\Omega \\), you can adjust \\( g_m \\) by changing the bias current or the dimensions (width \\( W \\) and length \\( L \\)) of \\( M_1 \\). Ensure that \\( g_m \\) is high enough to minimize the thermal noise contribution of \\( R_F \\), as a higher \\( g_m \\) reduces the effective noise resistance.\n\n### 2. **Optimize \\( R_F \\):**\n   - \\( R_F \\) contributes thermal noise to the circuit. To minimize its noise contribution, \\( R_F \\) should be as large as possible while still satisfying the input impedance requirement. This can be achieved by increasing \\( g_m \\) of \\( M_1 \\), which allows \\( R_F \\) to be larger without violating the \\( R_{in} = 50 \\, \\Omega \\) constraint.\n\n### 3. **Minimize Noise from \\( M_1 \\):**\n   - The noise figure is also influenced by the noise generated by \\( M_1 \\). To minimize this:\n     - Use a transistor with a high \\( g_m \\) to reduce its noise contribution.\n     - Choose a transistor with low flicker noise and thermal noise characteristics.\n     - Operate \\( M_1 \\) in strong inversion and saturation for optimal noise performance.\n\n### 4. **Optimize \\( M_2 \\):**\n   - \\( M_2 \\) acts as a current source and should have minimal noise contribution. Ensure that \\( M_2 \\) has a high output impedance and is biased properly to minimize its noise.\n\n### 5. **Capacitor \\( C_1 \\):**\n   - Ensure that \\( C_1 \\) is large enough to act as an AC coupling capacitor without introducing significant impedance at the operating frequency. This prevents it from affecting the input impedance or noise performance.\n\n### 6. **Biasing:**\n   - Proper biasing of \\( M_1 \\) and \\( M_2 \\) is crucial to ensure that the transistors operate in their optimal regions for low noise and high \\( g_m \\).\n\n### 7. **Simulation and Iteration:**\n   - Use circuit simulation tools (e.g., SPICE) to verify the noise figure and input impedance. Iterate the design parameters (\\( g_m \\), \\( R_F \\), and bias currents) to achieve the desired performance.\n\nBy carefully balancing \\( g_m \\), \\( R_F \\), and the transistor operating points, the circuit can be optimized for a low noise figure while maintaining \\( R_{in} = 50 \\, \\Omega \\).",
        "format": "markdown",
        "sha256": "efba7ca1ac727deb638219f127310e9b58d999b89e64f1ec42152bc88406f426"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It gives the broadly correct direction of increasing gm and RF while maintaining the match, but uses an inadequate Rin = (1/gm) || RF relation and treats M2 as a current source rather than part of the inverter’s total gm. It misses the finite-ro mechanism that allows gm to exceed 1/Rs and lowers NF below 1 + gamma.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1136,
        "output_tokens": 666,
        "total_tokens": 1802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1136,
        "output_tokens": 666,
        "total_tokens": 1802,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the circuit shown for noise figure (NF) while maintaining \\( R_{in} = 50 \\, \\Omega \\), the following steps can be taken:\n\n### 1. **Adjust the Transconductance (\\( g_m \\)) of \\( M_1 \\):**\n   - The input impedance of the circuit is determined by the feedback resistor \\( R_F \\) and the transconductance \\( g_m \\) of \\( M_1 \\). Specifically:\n     \\[\n     R_{in} = \\frac{1}{g_m} \\parallel R_F\n     \\]\n   - To maintain \\( R_{in} = 50 \\, \\Omega \\), \\( g_m \\) must be chosen appropriately. For example, if \\( R_F \\) is large, \\( g_m \\) should be approximately \\( 1/50 \\, \\text{S} \\) (20 mS).\n\n### 2. **Minimize the Noise Contribution of \\( M_1 \\):**\n   - The noise figure is primarily influenced by the thermal noise of \\( M_1 \\). To minimize this:\n     - Use a transistor with a high \\( g_m \\) (within the constraint of \\( R_{in} \\)).\n     - Operate \\( M_1 \\) in strong inversion and at an optimal bias point to maximize \\( g_m \\) while minimizing \\( \\gamma \\) (the noise coefficient).\n\n### 3. **Optimize \\( R_F \\):**\n   - \\( R_F \\) contributes thermal noise to the circuit. To reduce its noise contribution:\n     - Use a large \\( R_F \\), as long as it does not violate the \\( R_{in} \\) constraint. A larger \\( R_F \\) reduces its noise current contribution.\n\n### 4. **Choose \\( M_2 \\) for Proper Biasing:**\n   - \\( M_2 \\) provides the biasing for \\( M_1 \\). Ensure that \\( M_2 \\) is chosen to provide the correct operating point for \\( M_1 \\) without introducing significant noise.\n\n### 5. **Minimize Parasitics:**\n   - Parasitic capacitances at the input node can degrade the noise figure. Minimize these by careful layout and by choosing transistors with low gate capacitance.\n\n### 6. **Use a Low-Noise Power Supply:**\n   - Noise from the power supply (\\( V_{DD} \\)) can couple into the circuit and degrade the noise figure. Use a clean, low-noise power supply.\n\n### 7. **Simulate and Iterate:**\n   - Use circuit simulation tools to verify the noise figure and input impedance. Adjust \\( g_m \\), \\( R_F \\), and other parameters iteratively to achieve the desired performance.\n\nBy carefully balancing \\( g_m \\), \\( R_F \\), and the operating conditions of \\( M_1 \\), the circuit can be optimized for a low noise figure while maintaining \\( R_{in} = 50 \\, \\Omega \\).",
        "format": "markdown",
        "sha256": "ea7f244d1719103be896485297b363a57d93d1c8ee2ebb5a0925aacb3d45c3e0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer uses an incorrect input-resistance relation and effectively pins gm near 1/50 Ω, missing the key finite-output-resistance result: gm can exceed 1/Rs while RF is increased to keep Rin at 50 Ω, allowing NF below 1 + gamma. The generic noise and layout suggestions do not address that optimization.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1136,
        "output_tokens": 623,
        "total_tokens": 1759,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1136,
        "output_tokens": 623,
        "total_tokens": 1759,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance (\\(Z_{in}\\)) of the circuit, we analyze the circuit at the input node \\(P\\), considering the small-signal equivalent model.\n\n### Key Observations:\n1. The input impedance is determined by the impedance seen at the gate of \\(M_1\\), which is connected to the input signal \\(I_{in}\\) through \\(C_{in}\\).\n2. The gate of \\(M_1\\) is a high-impedance node because the gate current of a MOSFET is negligible.\n3. The feedback resistor \\(R_F\\) and the rest of the circuit do not directly affect the input impedance at \\(P\\) because they are connected to the drain of \\(M_1\\), not its gate.\n\n### Input Impedance Calculation:\n- The impedance at the gate of \\(M_1\\) is dominated by the parallel combination of \\(R_{in}\\) and the impedance of \\(C_{in}\\).\n- The impedance of \\(C_{in}\\) is given by:\n  \\[\n  Z_{C_{in}} = \\frac{1}{j\\omega C_{in}}\n  \\]\n  where \\(\\omega = 2\\pi f\\) is the angular frequency of the input signal.\n\n- The total input impedance is:\n  \\[\n  Z_{in} = R_{in} \\parallel Z_{C_{in}}\n  \\]\n  Using the parallel impedance formula:\n  \\[\n  Z_{in} = \\frac{R_{in} \\cdot Z_{C_{in}}}{R_{in} + Z_{C_{in}}}\n  \\]\n\n- Substituting \\(Z_{C_{in}} = \\frac{1}{j\\omega C_{in}}\\):\n  \\[\n  Z_{in} = \\frac{R_{in} \\cdot \\frac{1}{j\\omega C_{in}}}{R_{in} + \\frac{1}{j\\omega C_{in}}}\n  \\]\n\n- Simplify:\n  \\[\n  Z_{in} = \\frac{R_{in}}{1 + j\\omega R_{in} C_{in}}\n  \\]\n\n### Final Expression:\nThe input impedance of the circuit is:\n\\[\nZ_{in} = \\frac{R_{in}}{1 + j\\omega R_{in} C_{in}}\n\\]\n\nThis is a frequency-dependent impedance, with the real part dominated by \\(R_{in}\\) at low frequencies and the imaginary part becoming significant at higher frequencies due to the capacitive reactance of \\(C_{in}\\).",
        "format": "markdown",
        "sha256": "b0abad77ace4d12fa82331f091ed14affd2fb631dd799087cc82307d59be86d5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misses the feedback path that sets the input impedance and incorrectly treats the input as a MOS gate isolated from the rest of the circuit. It gives a capacitor-based expression instead of the required Miller result, Rin = (RF + RD2)/(1 + A0).",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 543,
        "total_tokens": 816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 543,
        "total_tokens": 816,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance (\\(Z_{in}\\)) of the circuit, we analyze the circuit at the input node \\(P\\), considering the small-signal equivalent model.\n\n### Key Observations:\n1. The input impedance is determined by the impedance seen at the gate of \\(M_1\\), which is connected to the input signal \\(I_{in}\\) through \\(C_{in}\\).\n2. The gate of \\(M_1\\) is a high-impedance node because the gate current of a MOSFET is negligible.\n3. The feedback resistor \\(R_F\\) and the rest of the circuit do not directly affect the input impedance at \\(P\\) because they are connected to the drain of \\(M_1\\), not its gate.\n\n### Input Impedance Calculation:\n- The impedance at the gate of \\(M_1\\) is dominated by the parallel combination of \\(R_{in}\\) and the impedance of \\(C_{in}\\).\n- The impedance of \\(C_{in}\\) is given by:\n  \\[\n  Z_{C_{in}} = \\frac{1}{j\\omega C_{in}}\n  \\]\n  where \\(\\omega = 2\\pi f\\) is the angular frequency of the input signal.\n\n- The total input impedance is:\n  \\[\n  Z_{in} = R_{in} \\parallel Z_{C_{in}}\n  \\]\n  Using the parallel impedance formula:\n  \\[\n  Z_{in} = \\frac{R_{in} \\cdot Z_{C_{in}}}{R_{in} + Z_{C_{in}}}\n  \\]\n\n- Substituting \\(Z_{C_{in}} = \\frac{1}{j\\omega C_{in}}\\):\n  \\[\n  Z_{in} = \\frac{R_{in} \\cdot \\frac{1}{j\\omega C_{in}}}{R_{in} + \\frac{1}{j\\omega C_{in}}}\n  \\]\n\n- Simplify:\n  \\[\n  Z_{in} = \\frac{R_{in}}{1 + j\\omega R_{in} C_{in}}\n  \\]\n\n### Final Expression:\nThe input impedance is:\n\\[\nZ_{in} = \\frac{R_{in}}{1 + j\\omega R_{in} C_{in}}\n\\]\n\nThis is a frequency-dependent impedance, with the real part dominated by \\(R_{in}\\) at low frequencies and the imaginary part becoming significant at higher frequencies due to the capacitive reactance of \\(C_{in}\\).",
        "format": "markdown",
        "sha256": "d0410f2d42ff830783454b1ede602a797cdedc6aafb3c8f16da71e3d1caa7375"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer ignores the feedback path that determines the input impedance and incorrectly treats the input as an isolated MOS gate. It does not provide the required Miller-theorem result, \\(R_{in}=(R_F+R_{D2})/(1+A_0)\\).",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 540,
        "total_tokens": 813,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 540,
        "total_tokens": 813,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance (\\(Z_{in}\\)) of the circuit, we analyze the small-signal equivalent of the circuit. Here's the step-by-step process:\n\n---\n\n### 1. **Identify the Input Node**\nThe input node is at \\(P\\), where the current source \\(I_{in}\\) is connected. The impedance seen at this node is the input impedance \\(Z_{in}\\).\n\n---\n\n### 2. **Small-Signal Model of \\(M_1\\)**\nThe transistor \\(M_1\\) is a common-source amplifier. Its small-signal parameters include:\n- \\(g_{m1}\\): Transconductance of \\(M_1\\).\n- \\(r_{o1}\\): Output resistance of \\(M_1\\).\n\nThe impedance at the source of \\(M_1\\) is determined by the feedback resistor \\(R_F\\) and the impedance looking into the drain of \\(M_2\\).\n\n---\n\n### 3. **Feedback Effect of \\(R_F\\)**\nThe resistor \\(R_F\\) provides negative feedback. The impedance at the input node \\(P\\) is influenced by this feedback. The effective impedance at \\(P\\) is approximately:\n\n\\[\nZ_{in} \\approx R_F \\parallel \\frac{1}{g_{m1}}\n\\]\n\nwhere:\n- \\(R_F\\) is the feedback resistor.\n- \\(\\frac{1}{g_{m1}}\\) is the small-signal input impedance of \\(M_1\\).\n\n---\n\n### 4. **Impedance Looking into \\(M_2\\)**\nThe impedance looking into the drain of \\(M_2\\) is approximately \\(r_{o2}\\), where \\(r_{o2}\\) is the output resistance of \\(M_2\\). This impedance affects the overall impedance seen at \\(P\\).\n\n---\n\n### 5. **Final Expression for \\(Z_{in}\\)**\nCombining the effects of \\(R_F\\), \\(g_{m1}\\), and the impedance looking into \\(M_2\\), the input impedance is:\n\n\\[\nZ_{in} \\approx R_F \\parallel \\frac{1}{g_{m1}}\n\\]\n\nIf \\(R_F \\gg \\frac{1}{g_{m1}}\\), then:\n\n\\[\nZ_{in} \\approx \\frac{1}{g_{m1}}\n\\]\n\nOtherwise, the feedback resistor \\(R_F\\) dominates.\n\n---\n\n### 6. **Capacitive Effects**\nThe capacitor \\(C_{in}\\) at the input introduces a frequency-dependent impedance. At low frequencies, \\(C_{in}\\) has negligible effect, but at high frequencies, the impedance becomes:\n\n\\[\nZ_{in}(\\omega) = \\left( R_F \\parallel \\frac{1}{g_{m1}} \\right) \\parallel \\frac{1}{j\\omega C_{in}}\n\\]\n\nwhere \\(\\omega = 2\\pi f\\) is the angular frequency.\n\n---\n\n### Conclusion\nThe input impedance of the circuit is primarily determined by the feedback resistor \\(R_F\\) and the transconductance \\(g_{m1}\\) of \\(M_1\\). At low frequencies:\n\n\\[\nZ_{in} \\approx R_F \\parallel \\frac{1}{g_{m1}}\n\\]\n\nAt high frequencies, the impedance is reduced due to the capacitive reactance of \\(C_{in}\\).",
        "format": "markdown",
        "sha256": "44363222776bc228b485cbb10d72347fdb50ed6b9a0e1fe9edade5b8a73efb35"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The central input-impedance expression is incorrect: it should account for the amplifier gain and output resistance, yielding \u001b[0m(R_F+R_{D2})/(1+A_0)\u001b[0m. The proposed \u001b[0mR_F\\parallel1/g_{m1}\u001b[0m relation and added capacitive model miss the dominant feedback mechanism.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 711,
        "total_tokens": 984,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 273,
        "output_tokens": 711,
        "total_tokens": 984,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise due to the thermal noise spectrum \\( S_{th} \\) generated by the LDO regulator, follow these steps:\n\n### 1. **Understand the Noise Coupling Mechanism**\n   - The LDO regulator provides the supply voltage \\( V_{out} \\) to the VCO.\n   - Thermal noise from the LDO appears as fluctuations in \\( V_{out} \\), which modulates the VCO's oscillation frequency.\n   - This frequency modulation translates into phase noise at the VCO output.\n\n### 2. **Determine the VCO's Supply Sensitivity**\n   - The VCO's oscillation frequency \\( f_{osc} \\) depends on the supply voltage \\( V_{out} \\). The sensitivity of the VCO to supply noise is quantified by the supply sensitivity coefficient \\( K_{VCO} \\), defined as:\n     \\[\n     K_{VCO} = \\frac{\\Delta f_{osc}}{\\Delta V_{out}}\n     \\]\n   - \\( K_{VCO} \\) can be determined from the VCO design or measured experimentally.\n\n### 3. **Relate Supply Noise to Frequency Noise**\n   - The thermal noise spectrum \\( S_{th} \\) from the LDO appears as voltage noise \\( S_{V_{out}} \\) at the VCO supply. The corresponding frequency noise \\( S_{f} \\) is given by:\n     \\[\n     S_{f}(f) = (K_{VCO})^2 \\cdot S_{V_{out}}(f)\n     \\]\n\n### 4. **Convert Frequency Noise to Phase Noise**\n   - Phase noise \\( \\mathcal{L}(f) \\) is related to frequency noise \\( S_{f}(f) \\) by:\n     \\[\n     \\mathcal{L}(f) = \\frac{S_{f}(f)}{(2\\pi f)^2}\n     \\]\n   - Substituting \\( S_{f}(f) \\) from the previous step:\n     \\[\n     \\mathcal{L}(f) = \\frac{(K_{VCO})^2 \\cdot S_{V_{out}}(f)}{(2\\pi f)^2}\n     \\]\n\n### 5. **Express \\( S_{V_{out}}(f) \\) in Terms of \\( S_{th} \\)**\n   - The thermal noise spectrum \\( S_{th} \\) of the LDO contributes to \\( S_{V_{out}}(f) \\). If the LDO's noise transfer function is \\( H_{LDO}(f) \\), then:\n     \\[\n     S_{V_{out}}(f) = |H_{LDO}(f)|^2 \\cdot S_{th}(f)\n     \\]\n\n### 6. **Combine the Results**\n   - Substitute \\( S_{V_{out}}(f) \\) into the phase noise expression:\n     \\[\n     \\mathcal{L}(f) = \\frac{(K_{VCO})^2 \\cdot |H_{LDO}(f)|^2 \\cdot S_{th}(f)}{(2\\pi f)^2}\n     \\]\n\n### 7. **Interpret the Result**\n   - The phase noise \\( \\mathcal{L}(f) \\) at the VCO output depends on:\n     - The LDO's thermal noise spectrum \\( S_{th}(f) \\).\n     - The LDO's noise transfer function \\( H_{LDO}(f) \\).\n     - The VCO's supply sensitivity \\( K_{VCO} \\).\n     - The offset frequency \\( f \\).\n\nThis approach provides a systematic way to compute the VCO output phase noise due to the LDO's thermal noise.",
        "format": "markdown",
        "sha256": "cdd075cba420458ea5bb3ea6d26580856c9912054e250c895f9e3b1054a91520"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies supply-noise-induced frequency modulation and converts it to phase noise with the expected inverse-square offset dependence, using dfosc/dVout as the sensitivity. It omits the circuit-specific insight that the supply perturbs the varactors directly, making Kpush closely related to KVCO and motivating a lower KVCO.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1139,
        "output_tokens": 795,
        "total_tokens": 1934,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1139,
        "output_tokens": 795,
        "total_tokens": 1934,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise due to the thermal noise spectrum \\( S_{th} \\) generated by the LDO regulator, follow these steps:\n\n### 1. **Understand the Noise Coupling Mechanism**\n   - The LDO regulator provides the supply voltage \\( V_{out} \\) to the VCO.\n   - Thermal noise from the LDO appears as fluctuations in \\( V_{out} \\), which modulates the VCO's oscillation frequency.\n   - This frequency modulation translates into phase noise at the VCO output.\n\n### 2. **Determine the VCO's Supply Sensitivity**\n   - The VCO's oscillation frequency \\( f_{osc} \\) depends on the supply voltage \\( V_{out} \\). The sensitivity of the VCO to supply noise is quantified by the **supply sensitivity function** \\( K_{VCO} \\), defined as:\n     \\[\n     K_{VCO} = \\frac{\\Delta f_{osc}}{\\Delta V_{out}}\n     \\]\n   - \\( K_{VCO} \\) is typically provided in units of Hz/V or rad/s/V.\n\n### 3. **Relate Supply Noise to Frequency Noise**\n   - The thermal noise spectrum \\( S_{th} \\) from the LDO appears as voltage noise at \\( V_{out} \\). This noise causes frequency fluctuations in the VCO:\n     \\[\n     S_{f}(f) = K_{VCO}^2 \\cdot S_{th}(f)\n     \\]\n   - Here, \\( S_{f}(f) \\) is the frequency noise power spectral density.\n\n### 4. **Convert Frequency Noise to Phase Noise**\n   - Phase noise \\( \\mathcal{L}(f) \\) is related to frequency noise \\( S_{f}(f) \\) by:\n     \\[\n     \\mathcal{L}(f) = \\frac{S_{f}(f)}{(2\\pi f)^2}\n     \\]\n   - Substituting \\( S_{f}(f) \\) from the previous step:\n     \\[\n     \\mathcal{L}(f) = \\frac{K_{VCO}^2 \\cdot S_{th}(f)}{(2\\pi f)^2}\n     \\]\n\n### 5. **Final Expression for Phase Noise**\n   - The VCO output phase noise due to the LDO's thermal noise is:\n     \\[\n     \\mathcal{L}(f) = \\frac{K_{VCO}^2 \\cdot S_{th}(f)}{(2\\pi f)^2}\n     \\]\n   - Here:\n     - \\( K_{VCO} \\): VCO supply sensitivity (Hz/V or rad/s/V).\n     - \\( S_{th}(f) \\): Thermal noise spectrum of the LDO (V\\(^2\\)/Hz).\n     - \\( f \\): Offset frequency from the carrier (Hz).\n\n### 6. **Practical Considerations**\n   - Ensure \\( K_{VCO} \\) is measured or simulated accurately for the specific VCO design.\n   - \\( S_{th}(f) \\) can be obtained from the LDO's noise model or measurements.\n   - The phase noise contribution from the LDO should be combined with other noise sources (e.g., transistor noise, tank noise) for the total phase noise.\n\nThis approach provides a systematic way to compute the VCO output phase noise due to the LDO's thermal noise.",
        "format": "markdown",
        "sha256": "6c20761b5e85aa13004eebb15863550f662b397f9b53bfdc740b57c0f4573b7f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The core method is correct: convert LDO voltage noise to frequency noise using the supply sensitivity, then apply the inverse-square FM-to-phase-noise relationship. It omits the figure-specific insight that supply perturbations act directly on the varactors, linking Kpush to KVCO and making reduced KVCO a way to lower the noise conversion.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1139,
        "output_tokens": 730,
        "total_tokens": 1869,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1139,
        "output_tokens": 730,
        "total_tokens": 1869,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise due to the thermal noise spectrum \\( S_{th} \\) generated by the LDO regulator, follow these steps:\n\n### 1. **Understand the Noise Coupling Mechanism**\n   - The LDO regulator provides the supply voltage \\( V_{out} \\) to the VCO.\n   - Thermal noise from the LDO appears as fluctuations in \\( V_{out} \\), which modulates the VCO's oscillation frequency.\n   - This frequency modulation translates into phase noise at the VCO output.\n\n### 2. **Determine the VCO's Supply Sensitivity**\n   - The VCO's oscillation frequency \\( f_{osc} \\) depends on the supply voltage \\( V_{out} \\). The sensitivity of the VCO to supply noise is quantified by the **supply sensitivity function** \\( K_{VCO} \\), defined as:\n     \\[\n     K_{VCO} = \\frac{\\Delta f_{osc}}{\\Delta V_{out}}\n     \\]\n   - \\( K_{VCO} \\) is typically provided in the VCO's design specifications or can be derived from simulations.\n\n### 3. **Relate Supply Noise to Frequency Noise**\n   - The thermal noise spectrum \\( S_{th} \\) from the LDO appears as voltage noise \\( S_{V_{out}} \\) at the VCO supply. The corresponding frequency noise \\( S_{f} \\) is given by:\n     \\[\n     S_{f}(f) = (K_{VCO})^2 \\cdot S_{V_{out}}(f)\n     \\]\n\n### 4. **Convert Frequency Noise to Phase Noise**\n   - Phase noise \\( \\mathcal{L}(f) \\) is related to frequency noise \\( S_{f}(f) \\) by:\n     \\[\n     \\mathcal{L}(f) = \\frac{S_{f}(f)}{(f - f_{osc})^2}\n     \\]\n   - Here, \\( f \\) is the offset frequency from the carrier \\( f_{osc} \\).\n\n### 5. **Substitute and Compute**\n   - Substitute \\( S_{V_{out}}(f) = S_{th}(f) \\) into the equations above:\n     \\[\n     S_{f}(f) = (K_{VCO})^2 \\cdot S_{th}(f)\n     \\]\n     \\[\n     \\mathcal{L}(f) = \\frac{(K_{VCO})^2 \\cdot S_{th}(f)}{(f - f_{osc})^2}\n     \\]\n\n### 6. **Interpret the Result**\n   - The phase noise \\( \\mathcal{L}(f) \\) at the VCO output is directly proportional to the thermal noise spectrum \\( S_{th}(f) \\) of the LDO and the square of the VCO's supply sensitivity \\( K_{VCO} \\).\n   - The offset frequency \\( f - f_{osc} \\) determines how the noise is shaped in the frequency domain.\n\n### 7. **Practical Considerations**\n   - Ensure \\( K_{VCO} \\) is accurately characterized for the specific VCO design.\n   - Include other noise sources (e.g., flicker noise, device noise) in the overall phase noise analysis if needed.\n\nBy following these steps, you can compute the VCO output phase noise due to the LDO's thermal noise.",
        "format": "markdown",
        "sha256": "e7d76b6ecc90d700b3cc6fbc35c7f7ce643f2ffdda3c764a9a84f69111e6aeeb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing, maps the LDO voltage-noise spectrum through the supply-to-frequency sensitivity, and applies the inverse-square offset-frequency FM-to-phase-noise conversion. The squared sensitivity relationship also captures why reducing that sensitivity reduces the noise; the offset notation is slightly inconsistent but does not change the intended result.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1139,
        "output_tokens": 726,
        "total_tokens": 1865,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1139,
        "output_tokens": 726,
        "total_tokens": 1865,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Adding a capacitor \\( C_T \\) to the tail node in this differential LC oscillator circuit impacts the phase noise in the following way:\n\n1. **Reduction in Tail Current Noise Coupling**: The capacitor \\( C_T \\) acts as a low-pass filter at the tail node, reducing the high-frequency noise from the current source \\( I_{SS} \\). This decreases the coupling of noise from the tail current source into the oscillator, which is a significant contributor to phase noise.\n\n2. **Improved Symmetry**: By stabilizing the tail node voltage, \\( C_T \\) helps maintain better symmetry in the differential operation of the circuit. Improved symmetry reduces the upconversion of low-frequency noise to phase noise.\n\n3. **Impact on Phase Noise**: The overall effect is a reduction in phase noise, particularly at close-in offset frequencies. This is because the noise from the tail current source is less likely to modulate the oscillation frequency.\n\nHowever, the value of \\( C_T \\) must be chosen carefully. If \\( C_T \\) is too large, it could slow down the switching speed of the transistors \\( M_1 \\) and \\( M_2 \\), potentially degrading the oscillator's performance. Conversely, if \\( C_T \\) is too small, it may not effectively filter the noise.\n\nIn summary, adding \\( C_T \\) to the tail node generally reduces phase noise by filtering noise from the tail current source and improving circuit symmetry.",
        "format": "markdown",
        "sha256": "e6bfb86263f0797a0e41694ec49fba2f4a008e34244f46f138a93021d4764384"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It concludes that CT generally reduces phase noise through tail-noise filtering and improved symmetry, missing the non-monotonic effect and Razavi’s class-C, flicker-upconversion, and instability mechanisms. The generic warning about excessive CT slowing switching does not establish the phase-noise tradeoff.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 298,
        "total_tokens": 1090,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 298,
        "total_tokens": 1090,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Adding a capacitor \\( C_T \\) to the tail node in this differential LC oscillator circuit impacts the phase noise in the following way:\n\n1. **Reduction in Tail Current Noise Coupling**: The capacitor \\( C_T \\) acts as a low-pass filter at the tail node, reducing the high-frequency noise from the current source \\( I_{SS} \\). This decreases the coupling of noise from the tail current source into the oscillator, which is a significant contributor to phase noise.\n\n2. **Improved Symmetry**: By stabilizing the tail node voltage, \\( C_T \\) helps maintain better symmetry in the differential operation of the circuit. Improved symmetry reduces the upconversion of low-frequency noise into phase noise.\n\n3. **Impact on Phase Noise**: The overall effect is a reduction in phase noise, particularly at close-in offset frequencies. This is because the filtering action of \\( C_T \\) suppresses noise sources that would otherwise modulate the oscillation frequency.\n\nHowever, the value of \\( C_T \\) must be chosen carefully. If \\( C_T \\) is too large, it could slow down the switching speed of the transistors \\( M_1 \\) and \\( M_2 \\), potentially degrading the oscillator's performance. Conversely, if \\( C_T \\) is too small, it may not effectively filter the noise.\n\nIn summary, adding \\( C_T \\) to the tail node generally reduces phase noise by filtering noise from the tail current source and improving circuit symmetry.",
        "format": "markdown",
        "sha256": "6b3c9c37c1b6eab0f859f5d930b4b5c4cf6776b0509cf1e15f209d6645512e70"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer concludes that CT generally reduces phase noise through filtering, a monotonic-improvement claim the golden solution scores 1. It misses the nonmonotonic effect and the class-C improvement and specific degradation mechanisms.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 303,
        "total_tokens": 1095,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 303,
        "total_tokens": 1095,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Adding a capacitor \\( C_T \\) to the tail node in this differential LC oscillator circuit impacts the phase noise in the following way:\n\n1. **Reduction in Tail Current Noise Coupling**: The capacitor \\( C_T \\) acts as a low-pass filter at the tail node, reducing the high-frequency noise from the current source \\( I_{SS} \\). This decreases the coupling of noise from the tail current source into the oscillator, which is a significant contributor to phase noise.\n\n2. **Improved Symmetry**: By stabilizing the tail node voltage, \\( C_T \\) helps maintain better symmetry in the differential operation of the circuit. This reduces the amplitude-to-phase noise conversion, further improving phase noise performance.\n\n3. **Trade-off with Oscillation Amplitude**: While \\( C_T \\) improves phase noise, it may slightly reduce the oscillation amplitude due to the additional loading at the tail node. However, this effect is typically small compared to the phase noise improvement.\n\n### Overall Effect:\nAdding \\( C_T \\) to the tail node generally **reduces the phase noise** of the oscillator, making it more stable and less sensitive to noise from the tail current source.",
        "format": "markdown",
        "sha256": "0b41ef987e81f1714ab43c0834f9c74b03000dbb2c808f09be8216e46282ca2a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It claims CT generally reduces phase noise through tail-node filtering, missing the nonmonotonic effect and the class-C improvement and degradation mechanisms.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 241,
        "total_tokens": 1033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 792,
        "output_tokens": 241,
        "total_tokens": 1033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To estimate the oscillation frequency of the circuit shown, we need to analyze the LC tank circuit formed by the inductors and capacitors. The oscillation frequency of an LC circuit is given by:\n\n\\[\nf = \\frac{1}{2\\pi\\sqrt{LC}}\n\\]\n\nWhere:\n- \\(L\\) is the inductance of the inductors.\n- \\(C\\) is the capacitance of the capacitors.\n\n### Steps to Estimate the Oscillation Frequency:\n1. **Identify the LC Tank Circuit**: The inductors (\\(L\\)) and capacitors (\\(C\\)) in the circuit form the resonant LC tank. The circuit appears to have two coupled LC tanks, but the oscillation frequency is primarily determined by the individual LC components.\n\n2. **Determine \\(L\\) and \\(C\\)**: If the values of \\(L\\) and \\(C\\) are provided, substitute them into the formula. If not, you would need to know or estimate these values based on the circuit design.\n\n3. **Calculate the Frequency**: Substitute the values of \\(L\\) and \\(C\\) into the formula to compute the oscillation frequency.\n\n### Example:\nIf \\(L = 1 \\, \\mu\\text{H}\\) and \\(C = 1 \\, \\text{pF}\\), the oscillation frequency is:\n\n\\[\nf = \\frac{1}{2\\pi\\sqrt{(1 \\times 10^{-6})(1 \\times 10^{-12})}}\n\\]\n\n\\[\nf = \\frac{1}{2\\pi\\sqrt{10^{-18}}}\n\\]\n\n\\[\nf = \\frac{1}{2\\pi \\times 10^{-9}}\n\\]\n\n\\[\nf \\approx 159 \\, \\text{MHz}\n\\]\n\nIf you provide the specific values of \\(L\\) and \\(C\\), I can calculate the exact oscillation frequency for this circuit.",
        "format": "markdown",
        "sha256": "21ea89829b29c9139193ac43f02d64ef5a753996139ab28d7d00b70b49f4bbc1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly gives the uncoupled LC tank resonance as a starting point, but misses the essential coupling-induced frequency shift (approximately ±αω0/(2Q)). The arbitrary numerical example does not estimate the coupled oscillator’s frequency.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 405,
        "total_tokens": 1529,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 405,
        "total_tokens": 1529,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To estimate the oscillation frequency of the circuit shown, we need to analyze the LC tank circuit formed by the inductors and capacitors. The oscillation frequency of an LC circuit is given by:\n\n\\[\nf = \\frac{1}{2\\pi \\sqrt{L C}}\n\\]\n\nWhere:\n- \\(L\\) is the inductance of the inductors.\n- \\(C\\) is the capacitance of the capacitors.\n\n### Steps to Estimate the Oscillation Frequency:\n1. **Identify the LC Tank Circuit**: The inductors (\\(L\\)) and capacitors (\\(C\\)) in the circuit form the resonant LC tank circuit. The circuit oscillates at the resonant frequency of this tank.\n\n2. **Determine \\(L\\) and \\(C\\)**: The values of \\(L\\) and \\(C\\) are typically provided in the circuit specifications. If not, they must be measured or assumed based on the design.\n\n3. **Calculate the Frequency**: Substitute the values of \\(L\\) and \\(C\\) into the formula above to compute the oscillation frequency.\n\n### Example:\nIf the inductance \\(L = 10 \\, \\mu\\text{H}\\) and the capacitance \\(C = 1 \\, \\text{pF}\\), the oscillation frequency is:\n\n\\[\nf = \\frac{1}{2\\pi \\sqrt{(10 \\times 10^{-6})(1 \\times 10^{-12})}}\n\\]\n\n\\[\nf = \\frac{1}{2\\pi \\sqrt{10^{-17}}}\n\\]\n\n\\[\nf = \\frac{1}{2\\pi \\times 10^{-8.5}}\n\\]\n\n\\[\nf \\approx 1.59 \\, \\text{GHz}\n\\]\n\nThus, the oscillation frequency depends on the specific values of \\(L\\) and \\(C\\) in the circuit.",
        "format": "markdown",
        "sha256": "679a23fc241fb724aced17833296223985c626251833a80277438212ef4cfd28"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It gives the LC tank resonance as a baseline but misses the central coupling-induced frequency shift. Its illustrative numerical example is also incorrect, so the answer is only partially correct.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 398,
        "total_tokens": 1522,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1124,
        "output_tokens": 398,
        "total_tokens": 1522,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "default",
        "api_model": "openai/gpt-4o-2024-11-20",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To estimate the oscillation frequency of the circuit shown, we need to analyze the LC tank circuit formed by the inductors and capacitors. The oscillation frequency of an LC circuit is given by:\n\n\\[\nf = \\frac{1}{2\\pi \\sqrt{L C}}\n\\]\n\nWhere:\n- \\(L\\) is the inductance of the inductors.\n- \\(C\\) is the capacitance of the capacitors.\n\n### Steps to Estimate the Oscillation Frequency:\n1. **Identify the LC Tank Circuit**: The inductors (\\(L\\)) and capacitors (\\(C\\)) in the circuit form the resonant LC tank. The circuit appears to have two identical LC tanks (one for each stage), but the oscillation frequency will primarily depend on the values of \\(L\\) and \\(C\\) in each tank.\n\n2. **Assume Symmetry**: If the inductors and capacitors are identical in both stages, the oscillation frequency will be the same for both tanks.\n\n3. **Plug in Values**: If the values of \\(L\\) and \\(C\\) are known, substitute them into the formula to calculate the oscillation frequency. If the values are not provided, the frequency cannot be numerically determined but can still be expressed symbolically as:\n\n\\[\nf = \\frac{1}{2\\pi \\sqrt{L C}}\n\\]\n\n### Additional Notes:\n- The circuit shown is a differential oscillator, and the cross-coupled transistors provide the necessary negative resistance to sustain oscillations.\n- The current sources (\\(I_{SS}\\)) bias the transistors and ensure proper operation of the oscillator.\n\nIf you provide the values of \\(L\\) and \\(C\\), I can calculate the exact oscillation frequency for you.",
        "format": "markdown",
        "sha256": "5d6037c5be23672922acb992eb0e0151473d10438fd54bb130a9f6541062c20d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly gives the LC tank resonance as a baseline, but omits the essential coupling-induced frequency shift, so it does not estimate the circuit’s actual oscillation frequency.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 368,
        "total_tokens": 1492,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1024,
        "input_tokens": 1124,
        "output_tokens": 368,
        "total_tokens": 1492,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 0,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    }
  ]
}
