{
  "model_key": "qwen_37_plus",
  "display_name": "Qwen 3.7 Plus",
  "provider": "qwen",
  "evaluation_model_ids": [],
  "thinking_effort": "max",
  "configuration_note": "Qwen 3.7 Plus answered the 50 tasks in three rollouts through OpenRouter's chat completions route (qwen/qwen3.7-plus) at maximum reasoning effort. Requests set temperature to 0 and max_tokens to 131,072, the model's output limit. Each request was one user message holding only the question text and its figure: no title, headings or system prompt. Answers cut off at the output limit were re-run; every attempt is counted in tokens and cost. Answers were graded by GPT-6 Luna at maximum reasoning effort. Cost uses OpenRouter's list price for Qwen 3.7 Plus on 2026-11-10 ($0.32 input, $0.064 cached input, $1.28 output per 1M tokens).",
  "mode": "direct_qa",
  "summary": {
    "rollout_count": 3,
    "answer_count": 150,
    "scores": {
      "overall": {
        "gpt_6_luna_max": {
          "response_count": 150,
          "correct_count": 86,
          "incorrect_count": 64,
          "partial_credit_count": 49,
          "zero_count": 15,
          "mean_score_0_to_4": 2.8733333333333335,
          "score_percent": 71.83333333333334,
          "score_distribution": {
            "0": 15,
            "1": 21,
            "2": 18,
            "3": 10,
            "4": 86
          }
        },
        "active": {
          "response_count": 150,
          "correct_count": 86,
          "incorrect_count": 64,
          "partial_credit_count": 49,
          "zero_count": 15,
          "mean_score_0_to_4": 2.8733333333333335,
          "score_percent": 71.83333333333334,
          "score_distribution": {
            "0": 15,
            "1": 21,
            "2": 18,
            "3": 10,
            "4": 86
          }
        }
      },
      "part1": {
        "gpt_6_luna_max": {
          "response_count": 90,
          "correct_count": 68,
          "incorrect_count": 22,
          "partial_credit_count": 9,
          "zero_count": 13,
          "mean_score_0_to_4": 3.2444444444444445,
          "score_percent": 81.11111111111111,
          "score_distribution": {
            "0": 13,
            "1": 2,
            "2": 3,
            "3": 4,
            "4": 68
          }
        },
        "active": {
          "response_count": 90,
          "correct_count": 68,
          "incorrect_count": 22,
          "partial_credit_count": 9,
          "zero_count": 13,
          "mean_score_0_to_4": 3.2444444444444445,
          "score_percent": 81.11111111111111,
          "score_distribution": {
            "0": 13,
            "1": 2,
            "2": 3,
            "3": 4,
            "4": 68
          }
        }
      },
      "part2": {
        "gpt_6_luna_max": {
          "response_count": 60,
          "correct_count": 18,
          "incorrect_count": 42,
          "partial_credit_count": 40,
          "zero_count": 2,
          "mean_score_0_to_4": 2.316666666666667,
          "score_percent": 57.91666666666667,
          "score_distribution": {
            "0": 2,
            "1": 19,
            "2": 15,
            "3": 6,
            "4": 18
          }
        },
        "active": {
          "response_count": 60,
          "correct_count": 18,
          "incorrect_count": 42,
          "partial_credit_count": 40,
          "zero_count": 2,
          "mean_score_0_to_4": 2.316666666666667,
          "score_percent": 57.91666666666667,
          "score_distribution": {
            "0": 2,
            "1": 19,
            "2": 15,
            "3": 6,
            "4": 18
          }
        }
      }
    },
    "by_rollout": {
      "1": {
        "response_count": 50,
        "correct_count": 28,
        "incorrect_count": 22,
        "partial_credit_count": 16,
        "zero_count": 6,
        "mean_score_0_to_4": 2.76,
        "score_percent": 69.0,
        "score_distribution": {
          "0": 6,
          "1": 8,
          "2": 6,
          "3": 2,
          "4": 28
        }
      },
      "2": {
        "response_count": 50,
        "correct_count": 31,
        "incorrect_count": 19,
        "partial_credit_count": 14,
        "zero_count": 5,
        "mean_score_0_to_4": 2.96,
        "score_percent": 74.0,
        "score_distribution": {
          "0": 5,
          "1": 6,
          "2": 6,
          "3": 2,
          "4": 31
        }
      },
      "3": {
        "response_count": 50,
        "correct_count": 27,
        "incorrect_count": 23,
        "partial_credit_count": 19,
        "zero_count": 4,
        "mean_score_0_to_4": 2.9,
        "score_percent": 72.5,
        "score_distribution": {
          "0": 4,
          "1": 7,
          "2": 6,
          "3": 6,
          "4": 27
        }
      }
    },
    "tokens": {
      "response_count": 150,
      "usage_record_count": 150,
      "complete_usage_count": 150,
      "missing_usage_count": 0,
      "missing_cached_input_count": 0,
      "complete": true,
      "totals": {
        "cached_input_tokens": 5760,
        "input_tokens": 208356,
        "output_tokens": 1236916,
        "total_tokens": 1445272
      },
      "known_totals": {
        "cached_input_tokens": 5760,
        "input_tokens": 208356,
        "output_tokens": 1236916,
        "total_tokens": 1445272
      }
    },
    "by_rollout_part": {
      "part1": {
        "1": {
          "response_count": 30,
          "correct_count": 23,
          "incorrect_count": 7,
          "partial_credit_count": 2,
          "zero_count": 5,
          "mean_score_0_to_4": 3.1666666666666665,
          "score_percent": 79.16666666666666,
          "score_distribution": {
            "0": 5,
            "1": 1,
            "2": 1,
            "4": 23
          }
        },
        "2": {
          "response_count": 30,
          "correct_count": 23,
          "incorrect_count": 7,
          "partial_credit_count": 3,
          "zero_count": 4,
          "mean_score_0_to_4": 3.2666666666666666,
          "score_percent": 81.66666666666667,
          "score_distribution": {
            "0": 4,
            "1": 1,
            "2": 1,
            "3": 1,
            "4": 23
          }
        },
        "3": {
          "response_count": 30,
          "correct_count": 22,
          "incorrect_count": 8,
          "partial_credit_count": 4,
          "zero_count": 4,
          "mean_score_0_to_4": 3.3,
          "score_percent": 82.5,
          "score_distribution": {
            "0": 4,
            "2": 1,
            "3": 3,
            "4": 22
          }
        }
      },
      "part2": {
        "1": {
          "response_count": 20,
          "correct_count": 5,
          "incorrect_count": 15,
          "partial_credit_count": 14,
          "zero_count": 1,
          "mean_score_0_to_4": 2.15,
          "score_percent": 53.75,
          "score_distribution": {
            "0": 1,
            "1": 7,
            "2": 5,
            "3": 2,
            "4": 5
          }
        },
        "2": {
          "response_count": 20,
          "correct_count": 8,
          "incorrect_count": 12,
          "partial_credit_count": 11,
          "zero_count": 1,
          "mean_score_0_to_4": 2.5,
          "score_percent": 62.5,
          "score_distribution": {
            "0": 1,
            "1": 5,
            "2": 5,
            "3": 1,
            "4": 8
          }
        },
        "3": {
          "response_count": 20,
          "correct_count": 5,
          "incorrect_count": 15,
          "partial_credit_count": 15,
          "zero_count": 0,
          "mean_score_0_to_4": 2.3,
          "score_percent": 57.49999999999999,
          "score_distribution": {
            "1": 7,
            "2": 5,
            "3": 3,
            "4": 5
          }
        }
      }
    }
  },
  "answers": [
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Doubling L and W on MOSFET Intrinsic Gain\n\n## Result: The intrinsic gain **doubles**.\n\n---\n\n## Step-by-Step Derivation\n\nThe intrinsic gain of a MOSFET is:\n\n$$A_v = g_m \\cdot r_o$$\n\n### 1. Transconductance ($g_m$)\n\n$$g_m = \\mu_n C_{ox} \\frac{W}{L} V_{ov}$$\n\nWhen both $W$ and $L$ are doubled, the ratio $W/L$ **remains unchanged**. Assuming the same overdrive voltage $V_{ov}$:\n\n$$g_m \\rightarrow g_m \\quad \\text{(unchanged)}$$\n\n### 2. Output Resistance ($r_o$)\n\n$$r_o = \\frac{1}{\\lambda I_D}$$\n\nThe channel-length modulation parameter $\\lambda$ is inversely proportional to $L$:\n\n$$\\lambda \\propto \\frac{1}{L}$$\n\nSince $W/L$ is unchanged, the drain current $I_D$ is also unchanged. Therefore:\n\n$$\\lambda \\rightarrow \\frac{\\lambda}{2} \\quad \\Rightarrow \\quad r_o \\rightarrow 2r_o \\quad \\text{(doubles)}$$\n\n### 3. Intrinsic Gain\n\n$$A_v = g_m \\cdot r_o \\rightarrow g_m \\cdot 2r_o = 2A_v$$\n\n---\n\n## Intuitive Summary\n\n| Parameter | Effect | Reason |\n|-----------|--------|--------|\n| $W/L$ | Unchanged | Both scale by 2× |\n| $I_D$ | Unchanged | $W/L$ and $V_{ov}$ unchanged |\n| $g_m$ | Unchanged | Depends on $W/L$ and $V_{ov}$ |\n| $\\lambda$ | Halved | $\\lambda \\propto 1/L$ |\n| $r_o$ | Doubled | $r_o \\propto L/I_D$ |\n| **$A_v$** | **Doubles** | $A_v = g_m \\cdot r_o$ |\n\n> **Key insight:** Doubling $L$ increases the Early voltage $V_A$ (since $V_A \\propto L$), which directly boosts $r_o$ and hence the intrinsic gain, while $g_m$ stays constant because the $W/L$ ratio is preserved.",
        "format": "markdown",
        "sha256": "1d19d3b002bb5714205f9fb3b733ac602d8449473eba9978828d2ebe69409547"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly explains that at fixed overdrive, doubling both dimensions leaves gm and ID approximately unchanged, while longer L reduces λ and approximately doubles ro, so intrinsic gain approximately doubles.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 1691,
        "total_tokens": 1721,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1175,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 1691,
        "total_tokens": 1721,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1175,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Doubling W and L on MOSFET Intrinsic Gain\n\n## Short Answer\n**The intrinsic gain doubles.**\n\n---\n\n## Derivation\n\nThe intrinsic gain of a MOSFET is:\n\n$$A_v = \\frac{g_m}{g_{ds}} = g_m \\cdot r_o$$\n\nLet's examine how each parameter scales when we double both $W$ and $L$ (keeping bias voltages constant, so $V_{ov} = V_{GS} - V_{th}$ is unchanged).\n\n### 1. Transconductance ($g_m$)\n\n$$g_m = \\mu C_{ox} \\frac{W}{L} V_{ov}$$\n\nSince both $W$ and $L$ are doubled, the ratio $W/L$ **remains unchanged**, so:\n\n$$g_m \\rightarrow g_m \\quad \\text{(no change)}$$\n\n### 2. Output Resistance ($r_o$)\n\n$$r_o = \\frac{1}{g_{ds}} = \\frac{V_A}{I_D} = \\frac{V_A' \\cdot L}{I_D}$$\n\nwhere $V_A' \\cdot L$ is the Early voltage (proportional to $L$).\n\nThe drain current is:\n\n$$I_D = \\frac{1}{2}\\mu C_{ox}\\frac{W}{L}V_{ov}^2$$\n\nSince $W/L$ is unchanged and $V_{ov}$ is constant, $I_D$ **remains unchanged**.\n\nHowever, $L$ doubles, so:\n\n$$r_o \\rightarrow 2\\,r_o \\quad \\text{(doubles)}$$\n\n### 3. Intrinsic Gain\n\n$$A_v = g_m \\cdot r_o \\rightarrow g_m \\cdot 2r_o = 2A_v$$\n\n---\n\n## Key Insight\n\nThe intrinsic gain can be expressed as:\n\n$$\\boxed{A_v = \\frac{2\\,V_A'\\,L}{V_{ov}}}$$\n\nThis shows that $A_v$ is **directly proportional to $L$** and **independent of $W$**. Therefore:\n\n| Change | Effect on $A_v$ |\n|---|---|\n| Double $W$ only | No change |\n| Double $L$ only | Doubles |\n| Double both $W$ and $L$ | **Doubles** |\n\n> **Physical intuition:** Doubling $L$ reduces channel-length modulation (larger Early voltage), which increases $r_o$ without affecting $g_m$ (since $W/L$ is preserved). This directly boosts the gain.",
        "format": "markdown",
        "sha256": "5eb403704394392431ceca32571d14b797a1c4a390814b6d0d9c532f6c33766a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that at fixed overdrive, doubling both dimensions leaves gm and ID approximately unchanged while doubling ro, so intrinsic gain doubles. The assumptions and scaling are consistent with the golden solution.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2252,
        "total_tokens": 2282,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1684,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2252,
        "total_tokens": 2282,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1684,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-001-double-length-and-width-mosfet-its-intrinsic",
      "part": "part1",
      "question_number": 1,
      "question": "If we double the length and width of a MOSFET, what happens to its intrinsic gain?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Effect of Doubling W and L on MOSFET Intrinsic Gain\n\n## Short Answer\nThe intrinsic gain **doubles**.\n\n---\n\n## Derivation\n\nThe intrinsic gain of a MOSFET is:\n\n$$A_v = g_m \\cdot r_o$$\n\nLet's analyze how each term changes when both $W$ and $L$ are doubled (i.e., $W \\to 2W$, $L \\to 2L$).\n\n### 1. Transconductance ($g_m$)\n\n$$g_m = \\sqrt{2 \\mu C_{ox} \\frac{W}{L} I_D}$$\n\nSince both $W$ and $L$ are doubled, the ratio $W/L$ **remains unchanged**. Assuming the bias current $I_D$ is held constant:\n\n$$g_m \\to g_m \\quad \\text{(no change)}$$\n\n### 2. Output Resistance ($r_o$)\n\n$$r_o = \\frac{V_A}{I_D} \\propto \\frac{L}{I_D}$$\n\nThe Early voltage $V_A$ is directly proportional to $L$. Since $L$ doubles and $I_D$ is constant:\n\n$$r_o \\to 2r_o \\quad \\text{(doubles)}$$\n\n### 3. Intrinsic Gain\n\n$$A_v = g_m \\cdot r_o \\to g_m \\cdot 2r_o = 2A_v$$\n\n---\n\n## Intuitive Summary\n\n| Parameter | Expression | Effect of doubling W & L |\n|-----------|-----------|--------------------------|\n| $W/L$ | — | Unchanged |\n| $g_m$ | $\\propto \\sqrt{W/L}$ | Unchanged |\n| $r_o$ | $\\propto L$ | Doubles |\n| **$A_v$** | $g_m \\cdot r_o$ | **Doubles** |\n\n> **Key insight:** Doubling $W$ and $L$ together preserves the $W/L$ ratio (and thus $g_m$), but the longer channel reduces channel-length modulation, increasing $r_o$ proportionally with $L$. The net result is a **2× increase** in intrinsic gain.",
        "format": "markdown",
        "sha256": "e4d4ea42f293f0657754c30fcf5e28af2b5835f71bf2b6b7d17caf900ceee963"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that doubling both dimensions preserves W/L and gm at the stated bias, while the longer channel approximately doubles ro, so intrinsic gain doubles. The constant-current assumption is consistent with the golden solution's constant-overdrive condition here.",
          "golden_solution_sha256": "b623efa74b67c0787641e221f1d6de9d7318205927fbcd9490d3ed132b5450df",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2003,
        "total_tokens": 2033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1527,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2003,
        "total_tokens": 2033,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1527,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Transconductance vs. Overdrive Voltage\n\n**Student A is correct** — for a given MOSFET (fixed W/L), the transconductance $g_m$ increases as the overdrive voltage $V_{OV}$ increases.\n\n## The Key Equation\n\nIn saturation, the drain current is:\n\n$$I_D = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}V_{OV}^2$$\n\nTransconductance is defined as $g_m = \\frac{\\partial I_D}{\\partial V_{GS}}$, which gives:\n\n$$\\boxed{g_m = \\mu_n C_{ox}\\frac{W}{L}V_{OV}}$$\n\nThis shows $g_m$ is **directly proportional** to $V_{OV}$. As you increase $V_{GS}$ (and thus $V_{OV}$), $g_m$ increases linearly.\n\n## Important Caveat — Fixed Current\n\nThere is a common source of confusion. If you rewrite $g_m$ as:\n\n$$g_m = \\frac{2I_D}{V_{OV}}$$\n\nit *looks* like $g_m$ decreases with $V_{OV}$. But this form is used when comparing **different transistors biased at the same drain current** $I_D$. In that scenario, a larger $V_{OV}$ means a smaller $W/L$, which reduces $g_m$.\n\n## Summary\n\n| Condition | Relationship | Who's right? |\n|---|---|---|\n| Fixed device (fixed $W/L$), increasing $V_{GS}$ | $g_m \\propto V_{OV}$ | **Student A** |\n| Fixed $I_D$, comparing different $W/L$ | $g_m \\propto 1/V_{OV}$ | Student B |\n\nSince the question simply asks about increasing the overdrive voltage of a MOSFET (implying a single device with increasing $V_{GS}$), **Student A is correct**.",
        "format": "markdown",
        "sha256": "7d418b12f8c887d0076ee0d077260dd0d8e05e6631894817a74bab8c9a0367a4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A as right for a fixed W/L, derives that gm increases linearly with VOV, and accurately explains the fixed-ID condition under which Student B’s claim applies.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1859,
        "total_tokens": 1901,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1859,
        "total_tokens": 1901,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Transconductance vs. Overdrive Voltage\n\n**Student A is correct** — for a given MOSFET (fixed W/L), the transconductance $g_m$ increases as the overdrive voltage $V_{OV}$ increases.\n\n## The Key Equation\n\nIn saturation, the drain current is:\n\n$$I_D = \\frac{1}{2}\\mu_n C_{ox}\\frac{W}{L}V_{OV}^2$$\n\nTransconductance is defined as $g_m = \\frac{\\partial I_D}{\\partial V_{GS}}$, which gives:\n\n$$\\boxed{g_m = \\mu_n C_{ox}\\frac{W}{L}V_{OV}}$$\n\nThis shows $g_m$ is **directly proportional** to $V_{OV}$. As you increase $V_{GS}$ (and thus $V_{OV}$), $g_m$ increases linearly.\n\n## Important Caveat — Fixed Current\n\nThere is a common source of confusion. If you rewrite $g_m$ as:\n\n$$g_m = \\frac{2I_D}{V_{OV}}$$\n\nThis shows that **at a fixed drain current** $I_D$, increasing $V_{OV}$ (by choosing a smaller W/L device) actually *decreases* $g_m$. This is a critical insight in analog design: for a given power budget (fixed $I_D$), you maximize $g_m$ by operating at a **low** overdrive voltage.\n\n## Summary\n\n| Condition | Relationship | Who's right? |\n|---|---|---|\n| Fixed device (W/L constant), increasing $V_{OV}$ | $g_m \\propto V_{OV}$ | **Student A** |\n| Fixed bias current $I_D$, increasing $V_{OV}$ | $g_m \\propto 1/V_{OV}$ | **Student B** |\n\nSince the question doesn't specify a fixed current, the most natural reading is a single device with increasing $V_{GS}$, making **Student A correct**.",
        "format": "markdown",
        "sha256": "9e28e045a295a66239207764277f79d9573583b674c36ec4274e1c2fdcfa083b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A for fixed W/L and explains that ID rises with VOV, making gm increase. The fixed-current caveat is also accurate.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1869,
        "total_tokens": 1911,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1869,
        "total_tokens": 1911,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1431,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-002-student-says-transconductance-mosfet-goes-up-as",
      "part": "part1",
      "question_number": 2,
      "question": "Student A says the transconductance of a MOSFET goes up as the overdrive voltage increases. Student B says it goes down. Who is correct?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "## Student A is correct.\n\nHere's why, using the standard long-channel MOSFET model in saturation.\n\n### The Key Equations\n\nThe drain current in saturation is:\n\n$$I_D = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} V_{OV}^2$$\n\nTransconductance is defined as $g_m = \\frac{\\partial I_D}{\\partial V_{GS}}$. Taking the derivative:\n\n$$\\boxed{g_m = \\mu_n C_{ox} \\frac{W}{L} V_{OV}}$$\n\nThis shows that **$g_m$ is directly proportional to $V_{OV}$**. As the overdrive voltage increases, $g_m$ increases linearly.\n\n### Where Student B Might Get Confused\n\nThere is an alternative expression for $g_m$:\n\n$$g_m = \\frac{2I_D}{V_{OV}}$$\n\nAt a glance, it looks like $g_m$ should *decrease* as $V_{OV}$ increases (since $V_{OV}$ is in the denominator). But this is a trap — **$I_D$ is not independent of $V_{OV}$**. Since $I_D \\propto V_{OV}^2$, substituting that in gives:\n\n$$g_m = \\frac{2 \\cdot \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} V_{OV}^2}{V_{OV}} = \\mu_n C_{ox} \\frac{W}{L} V_{OV}$$\n\nThe $V_{OV}^2$ in the numerator (from $I_D$) more than cancels the $V_{OV}$ in the denominator, leaving a net linear increase.\n\n### Bottom Line\n\n| Expression | What it tells you |\n|---|---|\n| $g_m = \\mu_n C_{ox} \\frac{W}{L} V_{OV}$ | $g_m \\uparrow$ as $V_{OV} \\uparrow$ ✅ |\n| $g_m = \\frac{2I_D}{V_{OV}}$ | Misleading if you forget $I_D$ also changes |\n\n**Student A is correct.** Increasing the overdrive voltage increases the transconductance.",
        "format": "markdown",
        "sha256": "be5750f770f5c7aa41dc421b3cdb88553b58dcb7eac437383bbb44d531549296"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies Student A and derives that, for fixed W/L, gm is proportional to VOV because ID rises as VOV squared. The explanation also addresses why 2ID/VOV does not imply a decrease.",
          "golden_solution_sha256": "e805626814432e31b3628b4bf4073fa0c2304a7c8ea8bad4f0422be86c312f74",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1335,
        "total_tokens": 1377,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 843,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 42,
        "output_tokens": 1335,
        "total_tokens": 1377,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 843,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Small-Signal Model: PMOS vs. NMOS\n\n## Short Answer\n\n**Yes**, the small-signal equivalent circuit topology of a PMOS device is **identical** to that of an NMOS device.\n\n---\n\n## The Small-Signal Model (Hybrid-π)\n\nFor **both** NMOS and PMOS, the small-signal model consists of:\n\n```\n        G ──────┬──── C_gd ─────┬───── D\n                │               │\n               C_gs         g_m·v_gs\n                │           (current source)\n               ─┴─              │\n                │               │\n        B ──────┴──── g_mb·v_bs ┘───── S\n                        │\n                       r_o\n                        │\n                        S\n```\n\nThe governing equation is the same for both:\n\n$$i_d = g_m \\, v_{gs} + g_{mb} \\, v_{bs} + \\frac{v_{ds}}{r_o}$$\n\n---\n\n## Why Are They Identical?\n\nThe small-signal model is derived by **linearizing** the large-signal drain current equation around a DC operating point using partial derivatives. Since both devices follow the same functional form of the current equation (just with different voltage polarities), the resulting incremental model has the **same structure**.\n\n---\n\n## What *Does* Differ?\n\nWhile the **topology** is identical, the **parameter values** differ due to device physics:\n\n| Parameter | NMOS | PMOS |\n|-----------|------|------|\n| **Transconductance** $g_m$ | Higher (μ_n ≈ 2–3× μ_p) | Lower for same W/L and I_D |\n| **Mobility** | μ_n (electrons) | μ_p (holes), typically 2–3× smaller |\n| **Body connection** | Usually tied to GND | Usually tied to V_DD |\n| **DC bias polarities** | V_GS > 0, V_DS > 0 | V_GS < 0, V_DS < 0 |\n\n---\n\n## Key Takeaway\n\n> The small-signal model is a **linearized, incremental** representation. The signs of the DC voltages and currents are absorbed into the definitions of the small-signal parameters (which are all treated as **positive** quantities). As a result, you can use the **exact same circuit diagram and equations** for both NMOS and PMOS — only the numerical values of $g_m$, $r_o$, $g_{mb}$, and the parasitic capacitances will differ.",
        "format": "markdown",
        "sha256": "860a65b0bb155faf31438e0bddfb7b458dafb548ab5314161d86b58611aa7f34"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that the PMOS small-signal model has the same form/topology as the NMOS model. The golden solution explicitly grants full credit for this conclusion; further polarity detail is not required.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2101,
        "total_tokens": 2131,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1536,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2101,
        "total_tokens": 2131,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1536,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Small-Signal Model: PMOS vs. NMOS\n\n## Short Answer\n\n**Yes.** The small-signal equivalent circuit of a PMOS transistor is **identical in topology and form** to that of an NMOS transistor. The same model applies to both, with the same polarity conventions for all controlled sources.\n\n---\n\n## The Identical Small-Signal Model\n\nFor both NMOS and PMOS, the low-frequency small-signal model consists of:\n\n```\n        G               D\n        │               │\n        │               │\n        │    ┌──────┐   │\n        ├────┤  r_o ├────┤\n        │    └──┬───┘   │\n        │       │       │\n        │    g_m·v_gs   │\n        │       │       │\n        │    g_mb·v_bs  │  (if body effect is included)\n        │       │       │\n        │       ▼       │\n        │               │\n        └───────┬───────┘\n                │\n                S\n```\n\nThe small-signal drain current is:\n\n$$i_d = g_m \\, v_{gs} + g_{mb} \\, v_{bs} + \\frac{v_{ds}}{r_o}$$\n\nThis equation has **exactly the same form** for both NMOS and PMOS.\n\n---\n\n## Why Are They Identical?\n\nThe small-signal parameters are defined as partial derivatives of the drain current $I_D$ evaluated at the DC operating point:\n\n| Parameter | Definition |\n|-----------|-----------|\n| $g_m$ | $\\partial I_D / \\partial V_{GS}$ |\n| $g_{mb}$ | $\\partial I_D / \\partial V_{BS}$ |\n| $r_o$ | $(\\partial I_D / \\partial V_{DS})^{-1}$ |\n\nWhen you carry out these derivatives for the PMOS large-signal equations (using the standard terminal voltage conventions $V_{GS} = V_G - V_S$, $V_{DS} = V_D - V_S$, etc.), the signs work out such that **all three parameters are positive** for both device types. The resulting linearized model therefore has the same structure and the same reference directions.\n\n---\n\n## What *Does* Differ?\n\nOnly the **numerical values** of the parameters differ, due to physical differences:\n\n| Parameter | NMOS | PMOS |\n|-----------|------|------|\n| $g_m$ | $\\mu_n C_{ox} \\frac{W}{L} V_{OV}$ | $\\mu_p C_{ox} \\frac{W}{L} |V_{OV}|$ |\n| Carrier mobility | $\\mu_n \\approx 2\\text{–}3 \\times \\mu_p$ | Lower → lower $g_m$ for same $W/L$ |\n| $r_o$ | $\\frac{1}{\\lambda_n I_D}$ | $\\frac{1}{\\lambda_p I_D}$ |\n| Parasitic capacitances | Depend on n-substrate junctions | Depend on p-well/n-well junctions |\n\n---\n\n## Practical Significance\n\nThis equivalence is extremely powerful:\n\n- **Unified analysis techniques** — You can apply the same small-signal analysis methods (KCL, KVL, test-source methods) to circuits containing both NMOS and PMOS devices without changing your approach.\n- **CMOS circuit design** — In CMOS amplifiers, current mirrors, and logic gates, you simply replace each transistor with its small-signal model and solve the resulting linear circuit, treating NMOS and PMOS devices identically.\n- **Intuitive design** — A designer can reason about a PMOS stage using the same mental framework as an NMOS stage, just with different parameter values.",
        "format": "markdown",
        "sha256": "0535b38336ebe8fa7b88ae913512a8345b28c7d1f07ccd193de4e8e88c22526e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly says the PMOS model has the same form as the NMOS model, which the golden solution explicitly awards full credit.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 8360,
        "total_tokens": 8390,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7533,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 8360,
        "total_tokens": 8390,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7533,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-003-small-signal-model-pmos-device-identical-nmos",
      "part": "part1",
      "question_number": 3,
      "question": "Is the small-signal model of a PMOS device identical to that of an NMOS device?",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Small-Signal Model: PMOS vs. NMOS\n\n## Short Answer\n\n**Yes**, the small-signal model of a PMOS transistor is **identical in topology and sign convention** to that of an NMOS transistor, provided the same terminal voltage and current reference directions are used.\n\n---\n\n## Why They Are Identical\n\nThe small-signal model is derived by linearizing the large-signal equations around a DC operating point using partial derivatives. When consistent sign conventions are applied (e.g., drain current $i_d$ defined as flowing **into** the drain, and voltages defined as $v_{gs} = v_g - v_s$, etc.), both devices yield the same model:\n\n```\n        G\n        │\n   ┌────┴────┐\n   │  C_gs   │\n   │         │\n   B──┤ g_mb·v_bs\n   │  │      │\n   │  ▼      │\n   │  ┌──┐   │\n   │  │  │ g_m·v_gs\n   │  │  │   │\n   │  ▼  │   │\n   │  └──┘   │\n   │    │    │\n   │   r_o   │\n   │    │    │\n   └────┴────┘\n        │\n        D\n```\n\n### Key Parameters (same form for both)\n\n| Parameter | Definition | Sign |\n|-----------|-----------|------|\n| $g_m$ | $\\partial I_D / \\partial V_{GS}$ | **Positive** for both |\n| $g_{mb}$ | $\\partial I_D / \\partial V_{BS}$ | **Positive** for both |\n| $r_o$ | $1 / (\\lambda I_D)$ | **Positive** for both |\n\n---\n\n## What *Does* Differ\n\nWhile the **model structure** is identical, the **parameter values** differ due to physical and biasing differences:\n\n- **Transconductance ($g_m$)**: Typically lower for PMOS because hole mobility ($\\mu_p$) is roughly **2–3× lower** than electron mobility ($\\mu_n$).\n- **Output resistance ($r_o$)**: Depends on the specific operating point and channel-length modulation parameter $\\lambda$.\n- **Parasitic capacitances**: Junction capacitances differ due to different doping profiles and physical layout (e.g., PMOS in an n-well).\n\n---\n\n## Common Source of Confusion\n\nIn practice, many textbooks and designers use **different current/voltage conventions** for PMOS (e.g., defining $I_{SD}$ from source to drain, or using $v_{sg}$ instead of $v_{gs}$). When this happens, the dependent source may appear to flip direction, creating the **illusion** of a different model. However, this is purely a notational choice — the underlying linearized model is the same.\n\n> **Bottom line:** If you define $i_d$, $v_{gs}$, $v_{ds}$, and $v_{bs}$ with the same reference directions for both devices, the small-signal equivalent circuits are **exactly the same**.",
        "format": "markdown",
        "sha256": "04d4bc4a2216f2d5d3453940265c7647321535ac566c9f6ad101d25de058c56b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly states that the PMOS small-signal model has the same form as the NMOS model, which the golden solution explicitly awards full credit; differences in parameter values do not change that conclusion.",
          "golden_solution_sha256": "ad8a01fc96398ca5ab0993a444ff64ba0cfcb88738d2a52872ea47f671e0635e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2731,
        "total_tokens": 2761,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 30,
        "output_tokens": 2731,
        "total_tokens": 2761,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2048,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis and the sketch description for $I_X$ versus $V_X$.\n\n**Circuit Analysis:**\n1.  **Component Identification:** The circuit contains an NMOS transistor ($M_1$) with its source connected to ground.\n2.  **Configuration:** The gate is connected directly to the drain. This is known as a **diode-connected transistor**.\n3.  **Voltages:**\n    *   The source voltage $V_S = 0$ V (ground).\n    *   The drain voltage $V_D = V_X$ (connected to the positive terminal of the source).\n    *   The gate voltage $V_G = V_X$ (connected to the drain).\n    *   Therefore, $V_{GS} = V_X$ and $V_{DS} = V_X$.\n4.  **Region of Operation:**\n    *   For an NMOS transistor to be ON, we need $V_{GS} > V_{TH}$ (Threshold Voltage). So, $V_X > V_{TH}$.\n    *   The condition for saturation is $V_{DS} \\ge V_{GS} - V_{TH}$.\n    *   Substituting the values: $V_X \\ge V_X - V_{TH}$, which simplifies to $V_{TH} \\ge 0$. Since $V_{TH}$ is positive for an enhancement-mode NMOS, this condition is always satisfied when the transistor is ON.\n    *   Thus, the transistor operates in the **saturation region** for all $V_X > V_{TH}$.\n\n**Current Equation:**\nThe current $I_X$ flowing into the drain is given by the saturation current equation for a MOSFET:\n$$I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{TH})^2 (1 + \\lambda V_{DS})$$\n\nSubstituting $V_{GS} = V_X$ and $V_{DS} = V_X$:\n$$I_X = \\frac{1}{2} k' \\frac{W}{L} (V_X - V_{TH})^2 (1 + \\lambda V_X)$$\n*(where $k' = \\mu_n C_{ox}$)*\n\nIgnoring channel length modulation ($\\lambda \\approx 0$) for a simple sketch:\n$$I_X \\approx \\frac{1}{2} k' \\frac{W}{L} (V_X - V_{TH})^2 \\quad \\text{for } V_X \\ge V_{TH}$$\n$$I_X = 0 \\quad \\text{for } V_X < V_{TH}$$\n\n**Sketch Description:**\nThe graph of $I_X$ versus $V_X$ will look like a quadratic curve (parabola) starting at the threshold voltage.\n\n*   **X-axis:** $V_X$\n*   **Y-axis:** $I_X$\n*   **Region 1 ($V_X < V_{TH}$):** The current $I_X$ is approximately **0**. The graph is a flat line along the horizontal axis.\n*   **Region 2 ($V_X \\ge V_{TH}$):** The current $I_X$ increases quadratically. The curve starts at $(V_{TH}, 0)$ and curves upwards like a parabola ($y = x^2$).\n\n**Visual Representation:**\n\n```text\n  I_X\n  ^\n  |\n  |                  /\n  |                /\n  |              /\n  |            /\n  |          /\n  |________/___________> V_X\n  0       V_TH\n```\n\n*   The flat line is from $V_X = -\\infty$ (or 0) to $V_X = V_{TH}$.\n*   The curve rises sharply after $V_{TH}$.",
        "format": "markdown",
        "sha256": "31dd6f90c91b2584d5f15feb55cae9d7883d308f0121a5a4cb81bc746858a4cd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, gives approximately zero current below threshold, and describes the quadratic rise above threshold. The added square-law and saturation reasoning are consistent with the golden solution.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 3905,
        "total_tokens": 4852,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3054,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 3905,
        "total_tokens": 4852,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3054,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis and the sketch of $I_X$ versus $V_X$.\n\n**Circuit Analysis:**\n1.  **Configuration:** The NMOS transistor $M_1$ has its Gate connected to its Drain. This is known as a **diode-connected transistor**.\n2.  **Voltages:**\n    *   The Source is grounded, so $V_S = 0$.\n    *   The Drain is connected to the positive terminal of the voltage source $V_X$, so $V_D = V_X$.\n    *   Since the Gate is connected to the Drain, $V_G = V_D = V_X$.\n    *   Therefore, $V_{GS} = V_X$ and $V_{DS} = V_X$.\n3.  **Operating Region:**\n    *   For an NMOS transistor to be in the saturation region, the condition is $V_{DS} \\ge V_{GS} - V_{TH}$.\n    *   Substituting the values: $V_X \\ge V_X - V_{TH}$, which simplifies to $V_{TH} \\ge 0$. Assuming a standard enhancement-mode NMOS ($V_{TH} > 0$), this condition is always met as long as the transistor is on.\n    *   Therefore, the transistor operates in the **saturation region** (or cutoff).\n\n**I-V Relationship:**\n*   **Cutoff Region ($V_X < V_{TH}$):** The transistor is off, so no current flows.\n    $$I_X = 0$$\n*   **Saturation Region ($V_X \\ge V_{TH}$):** The current follows the square-law equation for a MOSFET in saturation (ignoring channel length modulation for simplicity):\n    $$I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_X - V_{TH})^2$$\n\n**Sketch Description:**\nThe graph of $I_X$ versus $V_X$ will look like a rectified parabola.\n*   For $V_X$ from $0$ to $V_{TH}$, the current $I_X$ is **0**.\n*   At $V_X = V_{TH}$, the current starts to flow.\n*   For $V_X > V_{TH}$, the current increases quadratically (parabolic shape).\n\n**Sketch:**\n\n```\n  I_X\n  ^\n  |\n  |          /\n  |        /\n  |      /\n  |    /\n  |  /\n  |/\n  +-------------------> V_X\n  0    V_TH\n```\n\n**(More detailed sketch representation):**\n\n1.  Draw the horizontal axis as $V_X$ and the vertical axis as $I_X$.\n2.  Mark a point $V_{TH}$ on the $V_X$ axis.\n3.  Draw a flat line along the $V_X$ axis from $0$ to $V_{TH}$ (indicating $I_X = 0$).\n4.  Starting from $V_{TH}$, draw a curve that goes up and to the right with an increasing slope (a parabola shape, $y \\propto x^2$).\n\nHere is a generated plot representing this relationship:\n\n**Graph:**\n*   **X-axis:** $V_X$\n*   **Y-axis:** $I_X$\n*   **Curve:** Flat at 0 until $V_{TH}$, then curves upward like a parabola.\n\n$$ I_X = \\begin{cases} 0 & \\text{for } V_X < V_{TH} \\\\ \\frac{1}{2} k_n (V_X - V_{TH})^2 & \\text{for } V_X \\ge V_{TH} \\end{cases} $$\n*(where $k_n = \\mu_n C_{ox} \\frac{W}{L}$)*",
        "format": "markdown",
        "sha256": "7277bc519ae849de6f798ffe37349478d249d8e8483a5f34fd6ab32c01f6e846"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, explains that it is in saturation when on, and gives approximately zero current below threshold with a quadratic rise above it.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 2486,
        "total_tokens": 3433,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1633,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 2486,
        "total_tokens": 3433,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1633,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-004-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 4,
      "question": "Sketch IX versus VX in the circuit in the figure.",
      "figures": [
        "tasks/part1-004-sketch-ix-versus-vx/figure-01.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis and the sketch of $I_X$ versus $V_X$.\n\n**Circuit Analysis:**\n1.  **Component Identification:** The circuit contains an NMOS transistor ($M_1$) with its Gate connected to its Drain. This configuration is known as a **diode-connected transistor**.\n2.  **Voltages:**\n    *   The Source is connected to ground ($V_S = 0$).\n    *   The Drain and Gate are connected to the positive terminal of the voltage source $V_X$. Therefore, $V_D = V_G = V_X$.\n    *   This means $V_{GS} = V_X$ and $V_{DS} = V_X$.\n3.  **Region of Operation:**\n    *   For an NMOS transistor to be in the **saturation region**, the condition is $V_{DS} \\ge V_{GS} - V_{TH}$.\n    *   Substituting the values from this circuit: $V_X \\ge V_X - V_{TH}$, which simplifies to $V_{TH} \\ge 0$.\n    *   Assuming this is a standard enhancement-mode NMOS transistor (indicated by the broken channel line in the symbol), the threshold voltage $V_{TH}$ is positive. Therefore, the condition for saturation is always met whenever the transistor is turned on ($V_{GS} > V_{TH}$).\n    *   The transistor is in the **cutoff region** (off) when $V_{GS} < V_{TH}$, i.e., $V_X < V_{TH}$.\n\n**Current-Voltage Relationship:**\n*   **For $V_X < V_{TH}$:** The transistor is off, so no current flows.\n    $$I_X = 0$$\n*   **For $V_X \\ge V_{TH}$:** The transistor is in saturation. The current is given by the square-law equation (ignoring channel length modulation for a basic sketch):\n    $$I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_X - V_{TH})^2$$\n    This shows that $I_X$ is proportional to the square of $(V_X - V_{TH})$.\n\n**Sketch Description:**\nThe graph of $I_X$ versus $V_X$ will look like a parabola that starts at the threshold voltage $V_{TH}$.\n\n1.  **X-axis ($V_X$):** From $0$ to $V_{TH}$, the current $I_X$ is zero (flat line on the axis).\n2.  **At $V_X = V_{TH}$:** The current starts to flow.\n3.  **For $V_X > V_{TH}$:** The curve rises quadratically (parabolic shape), curving upwards.\n\n**Sketch:**\n\n```text\n  I_X\n   ^\n   |\n   |                  /\n   |                 /\n   |                /\n   |               /\n   |              /\n   |             /\n   |            /\n   |___________/___________> V_X\n              V_TH\n```\n\n*   The flat line on the horizontal axis represents the cutoff region ($0 < V_X < V_{TH}$).\n*   The curved line starting at $V_{TH}$ represents the saturation region, following a parabolic curve $I_X \\propto (V_X - V_{TH})^2$.",
        "format": "markdown",
        "sha256": "deeddfa5c9136b4ae55b4cd178e3042aa1af98198d7f54fc872111b0c4e1dae1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the diode-connected NMOS, explains that it is off below threshold and in saturation above threshold, and gives the expected quadratic rise in current.",
          "golden_solution_sha256": "769af5ac610bb7825c7abce92bf56d510d018662cbce83d47eef1dee2597750d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 3470,
        "total_tokens": 4417,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 947,
        "output_tokens": 3470,
        "total_tokens": 4417,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2718,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch $I_X$ versus $V_X$, we first need to analyze the circuit to determine the operating regions of the MOSFET $M_1$.\n\n**1. Circuit Analysis:**\n*   **Transistor Type:** The symbol indicates an NMOS transistor.\n*   **Gate Voltage ($V_G$):** Connected to $V_X$, so $V_G = V_X$.\n*   **Source Voltage ($V_S$):** Connected to ground, so $V_S = 0$ V.\n*   **Drain Voltage ($V_D$):** Connected to the positive terminal of a 1 V source, so $V_D = 1$ V.\n\nFrom these, we can determine the terminal voltages:\n*   Gate-Source Voltage: $V_{GS} = V_G - V_S = V_X$.\n*   Drain-Source Voltage: $V_{DS} = V_D - V_S = 1$ V.\n\n**2. Regions of Operation:**\nThe current $I_X$ is the drain current $I_D$. The behavior depends on the value of $V_X$ relative to the threshold voltage $V_{TH}$.\n\n*   **Cutoff Region ($V_X < V_{TH}$):**\n    The transistor is off because $V_{GS} < V_{TH}$.\n    $$I_X = 0$$\n\n*   **Saturation Region ($V_{TH} \\le V_X \\le V_{TH} + V_{DS}$):**\n    The transistor is on ($V_{GS} > V_{TH}$) and in saturation because $V_{DS} \\ge V_{GS} - V_{TH}$ (i.e., $1 \\text{ V} \\ge V_X - V_{TH}$).\n    Condition: $V_{TH} \\le V_X \\le V_{TH} + 1$.\n    The current equation is:\n    $$I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{TH})^2 = \\frac{1}{2} k' \\frac{W}{L} (V_X - V_{TH})^2$$\n    This is a parabolic curve.\n\n*   **Triode (Linear) Region ($V_X > V_{TH} + V_{DS}$):**\n    The transistor is in the linear region because $V_{DS} < V_{GS} - V_{TH}$ (i.e., $1 \\text{ V} < V_X - V_{TH}$).\n    Condition: $V_X > V_{TH} + 1$.\n    The current equation is:\n    $$I_X = \\mu_n C_{ox} \\frac{W}{L} \\left[ (V_{GS} - V_{TH})V_{DS} - \\frac{1}{2}V_{DS}^2 \\right]$$\n    Substituting $V_{DS} = 1$ V:\n    $$I_X = k' \\frac{W}{L} \\left[ (V_X - V_{TH})(1) - 0.5(1)^2 \\right] = k' \\frac{W}{L} (V_X - V_{TH} - 0.5)$$\n    This is a linear equation (straight line) with a positive slope.\n\n**3. Sketch Description:**\nThe plot of $I_X$ versus $V_X$ will have three distinct sections:\n1.  **For $V_X < V_{TH}$:** A flat line along the horizontal axis ($I_X = 0$).\n2.  **For $V_{TH} \\le V_X \\le V_{TH} + 1$:** A parabola starting from zero at $V_X = V_{TH}$ and increasing quadratically.\n3.  **For $V_X > V_{TH} + 1$:** A straight line with a constant positive slope, continuing from the parabola. The transition is smooth.\n\n**Sketch:**\n\n```\n  I_X\n  ^\n  |\n  |                                  /  (Linear Region)\n  |                                /\n  |                              /\n  |                            /\n  |                          /  (Saturation Region - Parabolic)\n  |                        /\n  |                      /\n  |____________________/___________> V_X\n  0                  V_TH      V_TH + 1\n```\n\n*   **$0$ to $V_{TH}$**: $I_X = 0$.\n*   **$V_{TH}$ to $V_{TH} + 1$**: $I_X$ increases as a square function (parabola).\n*   **$> V_{TH} + 1$**: $I_X$ increases linearly.",
        "format": "markdown",
        "sha256": "dd5e2125a51e0b0d4d91956fc3ac06c4c7fe75aa668597639a9b737e4d63ac7b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the cutoff, saturation, and triode regions and gives the appropriate quadratic-to-linear current trend with the transition at $V_X=V_{TH}+1\\,\\text{V}$.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 5104,
        "total_tokens": 6208,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4066,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 5104,
        "total_tokens": 6208,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4066,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch the relationship between $I_X$ and $V_X$, we need to analyze the operation of the NMOS transistor $M_1$ in the given circuit.\n\n**1. Circuit Analysis:**\n*   **Gate Voltage ($V_G$):** Connected to $V_X$, so $V_G = V_X$.\n*   **Source Voltage ($V_S$):** Connected to ground, so $V_S = 0$ V.\n*   **Drain Voltage ($V_D$):** Connected to the positive terminal of the 1 V source, so $V_D = 1$ V.\n*   **Current ($I_X$):** This is the drain current $I_D$ flowing into the drain.\n\nFrom these, we determine the terminal voltages:\n*   $V_{GS} = V_G - V_S = V_X$\n*   $V_{DS} = V_D - V_S = 1$ V\n\n**2. Regions of Operation:**\nLet $V_{TH}$ be the threshold voltage of the NMOS transistor. The transistor operates in three regions depending on $V_X$:\n\n*   **Cutoff Region ($V_X < V_{TH}$):**\n    The gate-source voltage is less than the threshold voltage ($V_{GS} < V_{TH}$). The transistor is off.\n    $$I_X = 0$$\n\n*   **Saturation Region ($V_{TH} \\le V_X \\le V_{TH} + 1$ V):**\n    The transistor is on ($V_{GS} > V_{TH}$) and the drain-source voltage is greater than or equal to the overdrive voltage ($V_{DS} \\ge V_{GS} - V_{TH}$).\n    Condition: $1 \\text{ V} \\ge V_X - V_{TH} \\Rightarrow V_X \\le V_{TH} + 1 \\text{ V}$.\n    The current equation is:\n    $$I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{TH})^2 = \\frac{1}{2} k (V_X - V_{TH})^2$$\n    (where $k = \\mu_n C_{ox} \\frac{W}{L}$)\n    This is a **parabolic** curve.\n\n*   **Triode (Linear) Region ($V_X > V_{TH} + 1$ V):**\n    The transistor is on and the drain-source voltage is less than the overdrive voltage ($V_{DS} < V_{GS} - V_{TH}$).\n    Condition: $1 \\text{ V} < V_X - V_{TH} \\Rightarrow V_X > V_{TH} + 1 \\text{ V}$.\n    The current equation is:\n    $$I_X = \\mu_n C_{ox} \\frac{W}{L} \\left[ (V_{GS} - V_{TH})V_{DS} - \\frac{1}{2}V_{DS}^2 \\right]$$\n    Substituting values ($V_{DS} = 1$):\n    $$I_X = k \\left[ (V_X - V_{TH})(1) - \\frac{1}{2}(1)^2 \\right] = k (V_X - V_{TH} - 0.5)$$\n    This is a **linear** equation (straight line) with respect to $V_X$.\n\n**3. Sketch Description:**\n\n*   **X-axis:** $V_X$\n*   **Y-axis:** $I_X$\n*   **From $V_X = -\\infty$ to $V_{TH}$:** The graph is a flat line on the x-axis ($I_X = 0$).\n*   **From $V_X = V_{TH}$ to $V_X = V_{TH} + 1$:** The graph is a parabola starting from zero and increasing quadratically.\n*   **For $V_X > V_{TH} + 1$:** The graph becomes a straight line with a constant positive slope, continuing smoothly from the parabola.\n\n**Sketch:**\n\n```\n  I_X\n  ^\n  |\n  |                                  /  (Linear Region)\n  |                                /\n  |                              /\n  |                            /\n  |                          /  (Saturation Region - Parabola)\n  |                        /\n  |                      /\n  |                    /\n  |__________________/____________________> V_X\n                 V_TH      V_TH + 1\n```\n\n**Detailed Plot:**\n\n1.  **$V_X < V_{TH}$**: $I_X = 0$.\n2.  **$V_{TH} < V_X < V_{TH} + 1$**: $I_X$ increases as a square function $(V_X - V_{TH})^2$.\n3.  **$V_X > V_{TH} + 1$**: $I_X$ increases linearly. The transition at $V_X = V_{TH} + 1$ is smooth because the slope of the parabola at that point matches the slope of the linear line.",
        "format": "markdown",
        "sha256": "0f89c899d1298dd3e9a6f272e1b0125f025f8109b566c854b21fa929bc34cf68"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies cutoff, the quadratic saturation-region rise up to V_X = V_TH + 1 V, and the roughly linear triode-region rise beyond it, with consistent equations and a smooth transition.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 4573,
        "total_tokens": 5677,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3455,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 4573,
        "total_tokens": 5677,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3455,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-005-sketch-ix-versus-vx",
      "part": "part1",
      "question_number": 5,
      "question": "Sketch IX versus VX in the circuit shown in the figure.",
      "figures": [
        "tasks/part1-005-sketch-ix-versus-vx/figure-02.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To sketch the relationship between $I_X$ and $V_X$, we need to analyze the operation of the NMOS transistor $M_1$ in the given circuit.\n\n**1. Circuit Analysis**\n*   **Gate Voltage ($V_G$):** Connected to $V_X$, so $V_{GS} = V_X - 0 = V_X$.\n*   **Drain Voltage ($V_D$):** Connected to the positive terminal of the 1 V source, so $V_{DS} = 1 \\text{ V} - 0 = 1 \\text{ V}$.\n*   **Source Voltage ($V_S$):** Connected to ground, so $V_S = 0 \\text{ V}$.\n*   **Current ($I_X$):** This is the drain current $I_D$ flowing into the drain.\n\n**2. Regions of Operation**\nThe behavior of the NMOS transistor depends on the relationship between $V_{GS}$ (which is $V_X$) and the threshold voltage $V_{TH}$, as well as $V_{DS}$ (which is fixed at 1 V).\n\n*   **Cutoff Region:**\n    *   Condition: $V_{GS} < V_{TH} \\Rightarrow V_X < V_{TH}$.\n    *   The transistor is off.\n    *   **Current:** $I_X = 0$.\n\n*   **Saturation Region:**\n    *   Condition: $V_{GS} > V_{TH}$ and $V_{DS} \\ge V_{GS} - V_{TH}$.\n    *   Substituting values: $V_X > V_{TH}$ and $1 \\ge V_X - V_{TH} \\Rightarrow V_X \\le V_{TH} + 1$.\n    *   So, for **$V_{TH} < V_X \\le V_{TH} + 1$**, the transistor is in saturation.\n    *   **Current Equation:** $I_X = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_{GS} - V_{TH})^2 = \\frac{1}{2} k (V_X - V_{TH})^2$.\n    *   This is a **parabolic** relationship where current increases quadratically with $V_X$.\n\n*   **Triode (Linear) Region:**\n    *   Condition: $V_{GS} > V_{TH}$ and $V_{DS} < V_{GS} - V_{TH}$.\n    *   Substituting values: $1 < V_X - V_{TH} \\Rightarrow V_X > V_{TH} + 1$.\n    *   So, for **$V_X > V_{TH} + 1$**, the transistor is in the triode region.\n    *   **Current Equation:** $I_X = \\mu_n C_{ox} \\frac{W}{L} \\left[ (V_{GS} - V_{TH})V_{DS} - \\frac{1}{2}V_{DS}^2 \\right]$.\n    *   Substituting $V_{DS} = 1$: $I_X = k \\left[ (V_X - V_{TH})(1) - 0.5 \\right] = k(V_X - V_{TH} - 0.5)$.\n    *   This is a **linear** relationship where current increases linearly with $V_X$.\n\n**3. Sketch Description**\nThe plot of $I_X$ versus $V_X$ will have the following characteristics:\n*   **X-axis:** $V_X$\n*   **Y-axis:** $I_X$\n*   **From $V_X = 0$ to $V_X = V_{TH}$:** The current is zero (flat line on the x-axis).\n*   **From $V_X = V_{TH}$ to $V_X = V_{TH} + 1$:** The current follows a parabolic curve ($I_X \\propto (V_X - V_{TH})^2$).\n*   **For $V_X > V_{TH} + 1$:** The current becomes a straight line with a constant positive slope. The transition from the parabola to the line is smooth.\n\n**Sketch:**\n\n```text\n  I_X\n  ^\n  |\n  |                                  /  (Linear Region)\n  |                                /\n  |                              /\n  |                            /\n  |                          /  (Saturation Region - Parabolic)\n  |                        /\n  |                      /\n  |                    /\n  |__________________/____________________> V_X\n  0                 V_TH            V_TH + 1\n  (Cutoff)\n```\n\n**Summary of the plot:**\n1.  **Flat line** at $I_X=0$ until $V_X$ reaches the threshold voltage $V_{TH}$.\n2.  **Parabolic curve** starting at $V_{TH}$ and ending at $V_{TH} + 1$ V.\n3.  **Straight line** with a positive slope for $V_X > V_{TH} + 1$ V.",
        "format": "markdown",
        "sha256": "8648bf1238e18f7082fddc7a64b17c55a3f5bcd9a36d571adc6c7c2228b85de3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the cutoff, quadratic saturation rise up to VTH + 1 V, and roughly linear triode-region rise beyond it, matching the required sketch.",
          "golden_solution_sha256": "da000995f2032c3caf224acfa4963413c96cebf89a3cc792e76c3a444d327ffc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 5081,
        "total_tokens": 6185,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3960,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1104,
        "output_tokens": 5081,
        "total_tokens": 6185,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3960,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided:\n\n1.  **Identify the Device:** The symbol represents a MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor). Specifically, the arrow on the terminal pointing inward towards the channel indicates it is an **N-channel MOSFET (NMOS)**. The separated gate plate (the vertical line on the left with a gap) confirms it is a MOSFET rather than a JFET.\n\n2.  **Analyze the Connections:**\n    *   The **Gate** (left terminal) is connected to ground ($0\\text{ V}$).\n    *   The **Source** (bottom-right terminal, typically the one connected to the lower potential in an NMOS) is connected to ground ($0\\text{ V}$).\n    *   Therefore, the Gate-to-Source voltage is **$V_{GS} = 0\\text{ V}$**.\n    *   The current $I_X$ is entering the Drain (top terminal).\n\n3.  **Determine Operation Mode:**\n    *   **Enhancement-mode NMOS (Standard):** For a standard enhancement-mode NMOS, the threshold voltage ($V_{th}$) is positive ($V_{th} > 0$). Since $V_{GS} = 0\\text{ V}$, which is less than $V_{th}$, the transistor is in the **cutoff region**. It acts as an open switch, and the current $I_X$ would be approximately zero. In this case, it does not act as a useful non-zero current source.\n    *   **Depletion-mode NMOS:** For a depletion-mode NMOS, the threshold voltage is negative ($V_{th} < 0$). Since $V_{GS} = 0\\text{ V}$, which is greater than $V_{th}$ ($0 > \\text{negative number}$), the transistor is **ON**. If the voltage at the top terminal (Drain) is sufficiently high such that $V_{DS} \\ge V_{GS} - V_{th}$ (i.e., $V_{DS} \\ge -V_{th}$), the transistor operates in the **saturation region**. In saturation, the drain current is approximately constant ($I_D \\approx I_{DSS}$), independent of $V_{DS}$.\n\n**Conclusion:**\nYes, the device **can** act as a current source, but **only if it is a depletion-mode NMOS transistor**. In that configuration (with $V_{GS} = 0$), it acts as a constant current source providing a current $I_{DSS}$. If it is a standard enhancement-mode NMOS, it is turned off and conducts no current.",
        "format": "markdown",
        "sha256": "3ecf22fd356b8b4ab2978912d322af7cb3844174e472fd9063db533c2723e594"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies M1 as an NMOS and misreads its connections, then concludes the drawn device can act as a current source. It misses that M1 is a diode-connected PMOS with low small-signal impedance.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 10430,
        "total_tokens": 10855,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9851,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 10430,
        "total_tokens": 10855,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9851,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided:\n\n**Yes, the device can act as a current source, provided it is a depletion-mode MOSFET.**\n\nHere is the detailed analysis:\n\n1.  **Identify the Device and Connections:**\n    *   The symbol represents a MOSFET (labeled $M_1$).\n    *   The **Gate** (left terminal) is connected to ground ($V_G = 0$).\n    *   The **Source** (bottom-right terminal, assuming standard NMOS orientation where source is at lower potential) is connected to ground ($V_S = 0$).\n    *   This sets the gate-to-source voltage **$V_{GS} = 0$ V**.\n    *   The current $I_X$ flows into the top terminal (Drain).\n\n2.  **Determine the Mode of Operation:**\n    *   **If it is an Enhancement-mode MOSFET (most common):** The threshold voltage $V_{th}$ is positive. Since $V_{GS} = 0 < V_{th}$, the transistor is in the **cutoff region**. It would be turned off, and $I_X$ would be approximately zero. In this case, it does not act as a useful current source.\n    *   **If it is a Depletion-mode MOSFET:** The symbol shows a solid vertical line for the channel, which is the standard schematic symbol for a depletion-mode device (enhancement mode typically has a broken or dashed line). For a depletion-mode NMOS, the threshold voltage $V_{th}$ is negative. Since $V_{GS} = 0 > V_{th}$, the transistor is **ON**.\n\n3.  **Current Source Behavior:**\n    *   For a depletion-mode MOSFET with $V_{GS} = 0$, the device conducts a specific saturation current often denoted as $I_{DSS}$.\n    *   If the voltage at the top terminal (Drain) is high enough such that $V_{DS} \\ge V_{GS} - V_{th}$ (which simplifies to $V_{DS} \\ge |V_{th}|$), the transistor operates in the **saturation region**.\n    *   In the saturation region, the drain current $I_X$ is relatively constant and independent of the drain voltage $V_{DS}$ (ignoring channel length modulation).\n    *   Therefore, under these conditions, the device acts as a **constant current source**.\n\n**Conclusion:**\nAssuming the solid channel line indicates a **depletion-mode MOSFET**, the configuration with $V_{GS}=0$ is a standard circuit used to create a constant current source. If it were a standard enhancement-mode MOSFET, it would be turned off. Given the specific symbol style, the answer is **Yes**.",
        "format": "markdown",
        "sha256": "9df35b9c2a153931c725abcc2c50f36d91f7913f0918278da2cd8cedf20b88b0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly concludes that the device can act as a current source and misreads the topology. M1 is a diode-connected PMOS with its gate and drain grounded; it presents low impedance (about 1/gm), not a constant-current output.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 14545,
        "total_tokens": 14970,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13942,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 14545,
        "total_tokens": 14970,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13942,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-006-device-act-as-current-source",
      "part": "part1",
      "question_number": 6,
      "question": "Can the device shown in the figure act as a current source?",
      "figures": [
        "tasks/part1-006-device-act-as-current-source/figure-03.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided:\n\n1.  **Identify the Device:** The symbol represents a MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor), labeled $M_1$. The arrow on the terminal pointing towards the channel indicates that it is an **N-channel** device (NMOS).\n\n2.  **Analyze the Connections:**\n    *   The **Gate** (the vertical plate on the left) is connected to **Ground** ($0\\text{ V}$).\n    *   The **Source** (the bottom-right terminal) is connected to **Ground** ($0\\text{ V}$).\n    *   The current $I_X$ is flowing into the Drain (top terminal).\n\n3.  **Determine the Gate-Source Voltage ($V_{GS}$):**\n    Since both the Gate and the Source are connected to ground, the voltage difference between them is:\n    $$V_{GS} = V_G - V_S = 0\\text{ V} - 0\\text{ V} = 0\\text{ V}$$\n\n4.  **Determine the Operating Region:**\n    *   For a standard **enhancement-mode NMOS** transistor (which is the most common type), the threshold voltage ($V_{th}$) is positive ($V_{th} > 0$).\n    *   For the transistor to turn on and conduct current, we need $V_{GS} > V_{th}$.\n    *   Since $V_{GS} = 0\\text{ V}$, which is less than $V_{th}$, the transistor is in the **cutoff region** (it is turned off).\n\n**Conclusion:**\nNo, the device shown in the figure cannot act as a useful current source. Because $V_{GS} = 0$, the enhancement-mode NMOS transistor is in the cutoff region, meaning no current flows ($I_X \\approx 0$). It effectively acts as an open circuit.\n\n*(Note: If the device were a **depletion-mode** NMOS, which has a negative threshold voltage, it would be turned on at $V_{GS}=0$ and could act as a constant current source. However, without specific indication, MOSFETs are typically assumed to be enhancement-mode.)*",
        "format": "markdown",
        "sha256": "ef9f47e47a7370a7a491befb91360fe9a7df7d1fd1c24328ff4894a34fe3e5bd"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misidentifies M1 as an NMOS and misreads its terminals. The drawn device is a diode-connected PMOS whose low impedance (about 1/gm) prevents it from acting as a current source; the candidate’s cutoff explanation is incorrect.",
          "golden_solution_sha256": "20b0fcb71c5ac038622c26f3ac86aaf2af15f4064029312681192c8362271780",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 8767,
        "total_tokens": 9192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 425,
        "output_tokens": 8767,
        "total_tokens": 9192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit's function.\n\n### 1. Component Identification\n*   **Transistor ($M_1$):** This is a **PMOS transistor**. We can identify this by the arrow on the source terminal pointing inward towards the channel. Additionally, the source terminal (top) is connected towards the positive supply ($V_{DD}$), which is the standard orientation for a PMOS device.\n    *   **Source (S):** The top terminal, connected to resistor $R_S$.\n    *   **Gate (G):** The left terminal, connected to input $V_{in}$.\n    *   **Drain (D):** The bottom terminal, connected to resistor $R_D$ and output $V_{out}$.\n*   **Resistors:**\n    *   **$R_S$:** This is the **Source Resistor**. It is connected between the source of the transistor and the supply voltage $V_{DD}$. It acts as a source degeneration resistor.\n    *   **$R_D$:** This is the **Drain Resistor** (or load resistor). It is connected between the drain of the transistor and ground.\n*   **Terminals:**\n    *   **$V_{in}$:** Input voltage applied to the Gate.\n    *   **$V_{out}$:** Output voltage taken from the Drain.\n    *   **$V_{DD}$:** Positive DC supply voltage.\n\n### 2. Circuit Configuration\nThis circuit is a **Common Source Amplifier** with **source degeneration**.\n*   It is \"Common Source\" because the input is applied to the Gate and the output is taken from the Drain (the Source is the common terminal for the AC signal path, although here it's connected to a resistor rather than directly to a rail, it acts as the reference).\n*   The resistor $R_S$ provides negative feedback, known as source degeneration.\n\n### 3. Circuit Operation & Analysis\n\n**DC Behavior (Biasing):**\n*   For the PMOS transistor to turn ON and conduct current, the Gate voltage ($V_{in}$) must be lower than the Source voltage by at least the threshold voltage magnitude ($|V_{th}|$). That is, $V_{SG} > |V_{th}|$.\n*   When $V_{in}$ is low (close to 0V), the transistor turns ON. Current flows from $V_{DD}$, through $R_S$, through the transistor ($M_1$), and through $R_D$ to ground.\n*   When $V_{in}$ is high (close to $V_{DD}$), the transistor turns OFF ($V_{SG} \\approx 0$). No current flows, and $V_{out}$ is pulled down to 0V through $R_D$.\n\n**AC Behavior (Amplification):**\n*   **Inverting Amplifier:** This circuit acts as an inverting amplifier.\n    *   If $V_{in}$ **decreases** (becomes more negative relative to the source), the source-gate voltage $V_{SG}$ increases. This increases the drain current $I_D$.\n    *   An increased current $I_D$ flowing through $R_D$ creates a larger voltage drop across it. Since $V_{out} = I_D \\times R_D$, the output voltage $V_{out}$ **increases**.\n    *   Conversely, if $V_{in}$ increases, $I_D$ decreases, and $V_{out}$ decreases.\n    *   Therefore, the output is 180° out of phase with the input.\n\n**Voltage Gain:**\nThe presence of the source resistor $R_S$ reduces the overall voltage gain compared to a simple common source amplifier, but it improves the linearity and stability of the circuit. The approximate small-signal voltage gain ($A_v$) is given by:\n\n$$A_v \\approx -\\frac{g_m R_D}{1 + g_m R_S}$$\n\nWhere $g_m$ is the transconductance of the MOSFET. If $g_m R_S \\gg 1$, the gain simplifies to approximately $-R_D / R_S$, making the gain dependent primarily on the ratio of the resistors rather than the transistor's properties.",
        "format": "markdown",
        "sha256": "4d115cf24ea5209712a5691ac1e46d44c4c2a8d804db8a2e6302e5ade3499faa"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the inverting gain −gm RD/(1 + gm RS), satisfying the full-credit rule.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 4627,
        "total_tokens": 5824,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3702,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 4627,
        "total_tokens": 5824,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3702,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit's function.\n\n### 1. Component Identification\n*   **$M_1$**: This is a MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor).\n    *   *Note on Symbol:* The symbol shows an arrow on the top terminal pointing towards the channel. In standard symbols, an arrow pointing in indicates an N-channel (NMOS) device, while an arrow pointing out indicates a P-channel (PMOS) device. However, the circuit topology and labels suggest a PMOS configuration (explained below).\n*   **$R_S$**: A resistor connected between the supply voltage $V_{DD}$ and the top terminal of the transistor. The label \"$S$\" typically stands for **Source**.\n*   **$R_D$**: A resistor connected between the bottom terminal of the transistor and Ground. The label \"$D$\" typically stands for **Drain**.\n*   **$V_{in}$**: The input voltage applied to the Gate of the transistor.\n*   **$V_{out}$**: The output voltage taken from the node between the transistor and resistor $R_D$.\n*   **$V_{DD}$**: The positive power supply voltage.\n\n### 2. Circuit Configuration\nBased on the labels and connections, this circuit is a **Common Source Amplifier with Source Degeneration**.\n\n*   **Transistor Type:** Although the arrow direction might suggest an NMOS, the placement of the resistors strongly implies a **PMOS** transistor.\n    *   The resistor labeled $R_S$ (Source Resistor) is connected to the positive supply $V_{DD}$. In a PMOS transistor, the Source is the terminal at the highest potential.\n    *   The resistor labeled $R_D$ (Drain Resistor) is connected to Ground. In a PMOS transistor, the Drain is at the lower potential.\n    *   Current flows from the Source (top) to the Drain (bottom).\n\n*   **Topology:**\n    *   **Input:** Applied to the Gate.\n    *   **Output:** Taken from the Drain.\n    *   **Common Terminal:** The Source is connected to the supply (AC ground), making this a \"Common Source\" configuration. The resistor $R_S$ provides \"source degeneration\" (negative feedback).\n\n### 3. Circuit Operation\nThis circuit functions as an **inverting amplifier**.\n\n*   **DC Bias:** Current flows from $V_{DD}$, through $R_S$, through the transistor $M_1$, and through $R_D$ to ground.\n*   **Signal Operation:**\n    *   When the input voltage **$V_{in}$ decreases** (becomes lower relative to $V_{DD}$), the Source-Gate voltage ($V_{SG}$) increases. This turns the PMOS transistor **ON** more strongly.\n    *   Increased current flows through the transistor and through $R_D$.\n    *   According to Ohm's law ($V = I \\cdot R$), the voltage drop across $R_D$ increases, causing **$V_{out}$ to increase**.\n    *   Conversely, if **$V_{in}$ increases**, the transistor turns off, current decreases, and **$V_{out}$ decreases**.\n    *   Therefore, a change in input produces an opposite change in output (Inverting).\n\n### 4. Small-Signal Gain\nThe approximate small-signal voltage gain ($A_v$) for this configuration (ignoring the transistor's output resistance $r_o$) is given by:\n\n$$A_v = \\frac{V_{out}}{V_{in}} \\approx -\\frac{g_m R_D}{1 + g_m R_S}$$\n\nWhere:\n*   $g_m$ is the transconductance of the MOSFET.\n*   The negative sign indicates the **inverting** nature of the amplifier.\n*   The resistor $R_S$ reduces the overall gain but improves the linearity and stability of the amplifier (this is the effect of source degeneration). If $R_S$ were 0, the gain would be simply $-g_m R_D$.",
        "format": "markdown",
        "sha256": "aa4396aad9e14bc8464f77c155b3b9826f837dae86db0561f5239b596fb6e33a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the inverting gain −gmRD/(1 + gmRS), matching the full-credit rule.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 11403,
        "total_tokens": 12600,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10506,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 11403,
        "total_tokens": 12600,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10506,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-007-pmos-common-source-source-degeneration",
      "part": "part1",
      "question_number": 7,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-007-pmos-common-source-source-degeneration/figure-04.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit's function.\n\n### 1. Circuit Identification\nThe circuit shown is a **PMOS Common-Source Amplifier with Source Degeneration**.\n\n*   **Transistor ($M_1$):** The symbol indicates a **PMOS** transistor. We can identify this because the arrow on the source terminal (the top terminal) points inward towards the channel. Additionally, the source is connected towards the positive supply voltage ($V_{DD}$), which is the standard configuration for a PMOS device.\n*   **Configuration:** The input ($V_{in}$) is applied to the **Gate**, and the output ($V_{out}$) is taken from the **Drain**. This topology defines a Common-Source amplifier.\n\n### 2. Component Breakdown\n*   **$V_{DD}$:** The positive DC supply voltage.\n*   **$R_S$ (Source Resistor):** Connected between the supply $V_{DD}$ and the source of the transistor. In amplifier design, this is known as a **degeneration resistor**. It provides negative feedback, which stabilizes the gain, increases linearity, and increases the input/output impedance, though it reduces the overall voltage gain.\n*   **$R_D$ (Drain Resistor):** Connected between the drain of the transistor and ground. This acts as the **load resistor**, converting the drain current into an output voltage ($V_{out}$).\n*   **$V_{in}$:** The input signal voltage applied to the gate.\n*   **$V_{out}$:** The output signal voltage measured at the drain node.\n\n### 3. DC Operation (Biasing)\n*   **Current Path:** DC current flows from the positive supply $V_{DD}$, through resistor $R_S$, into the Source of the PMOS transistor, out of the Drain, through resistor $R_D$, and finally to Ground.\n*   **Turn-on Condition:** For a PMOS transistor to conduct (turn ON), the Source-Gate voltage ($V_{SG}$) must be greater than the threshold voltage magnitude ($|V_{th}|$).\n    *   $V_S \\approx V_{DD} - I_D R_S$\n    *   $V_G = V_{in}$\n    *   Therefore, $V_{in}$ must be sufficiently lower than the source voltage for the transistor to be active.\n\n### 4. Small-Signal Analysis (Amplifier Behavior)\nThis circuit acts as an inverting voltage amplifier.\n\n*   **Gain Formula:** The small-signal voltage gain ($A_v$) can be approximated as:\n    $$A_v = \\frac{V_{out}}{V_{in}} \\approx \\frac{-g_m R_D}{1 + g_m R_S}$$\n    *(Where $g_m$ is the transconductance of the transistor).*\n\n*   **Inversion:** The negative sign in the gain formula indicates a **180-degree phase shift** (inversion).\n    *   If $V_{in}$ **increases** (becomes more positive), the gate-source voltage $V_{SG}$ decreases ($V_S - V_G$). This reduces the current $I_D$ flowing through the transistor. Consequently, the voltage drop across $R_D$ decreases, so $V_{out}$ **decreases**.\n    *   If $V_{in}$ **decreases**, the transistor turns on harder, current increases, and $V_{out}$ **increases**.\n\n*   **Effect of $R_S$:** The resistor $R_S$ reduces the gain (the denominator $1 + g_m R_S$ makes the fraction smaller) but makes the amplifier more linear and stable against variations in transistor parameters. If $g_m R_S \\gg 1$, the gain simplifies to approximately $-R_D / R_S$, making it dependent only on the resistor ratio.",
        "format": "markdown",
        "sha256": "6874a8c05ffb5a3054d857fc24f8a73705dae154cc0bd55d30bc672222676833"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS common-source stage with source degeneration and gives the inverting gain −gm RD/(1 + gm RS), satisfying the full-credit rule.",
          "golden_solution_sha256": "cd8fcec5f92210366117d02bce0f4174b55a012666155b3dfc965be2c669f3a3",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 5740,
        "total_tokens": 6937,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4901,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1197,
        "output_tokens": 5740,
        "total_tokens": 6937,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4901,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the configuration:\n\n### 1. Circuit Identification\nThis circuit is a **Common Drain Amplifier**, also widely known as a **Source Follower**.\n\n*   **Transistor ($M_1$):** It is an N-channel MOSFET (NMOS). We can identify this because the arrow on the source terminal points outward (away from the gate/channel).\n*   **Input ($V_{in}$):** Applied to the **Gate** of the transistor.\n*   **Output ($V_{out}$):** Taken from the **Source** of the transistor.\n*   **Drain:** Connected directly to the supply voltage $V_{DD}$ (which acts as an AC ground).\n*   **Resistor ($R_S$):** A source degeneration resistor connected between the source and ground.\n\n### 2. Operation Principle\nIn this configuration, the output voltage at the source \"follows\" the input voltage at the gate.\n*   When $V_{in}$ increases, the gate-to-source voltage ($V_{GS}$) increases, turning the transistor on harder.\n*   This increases the drain current ($I_D$), which flows through the resistor $R_S$.\n*   The increased current causes a larger voltage drop across $R_S$, raising $V_{out}$.\n*   As $V_{out}$ rises, it reduces the $V_{GS}$ (since $V_{GS} = V_{in} - V_{out}$), creating a negative feedback loop that stabilizes the circuit.\n\nThe relationship is approximately:\n$$V_{out} \\approx V_{in} - V_{GS(th)}$$\n(where $V_{GS(th)}$ is the threshold voltage plus a small overdrive voltage).\n\n### 3. Key Characteristics (Small-Signal Analysis)\n\n*   **Voltage Gain ($A_v$):**\n    The voltage gain is slightly less than unity (1).\n    $$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m R_S}{1 + g_m R_S}$$\n    Since $g_m R_S$ is typically large, the fraction is close to 1. Therefore, **$A_v \\approx 1$**. The output signal is in phase with the input signal (non-inverting).\n\n*   **Input Impedance ($Z_{in}$):**\n    Looking into the gate of a MOSFET, the impedance is extremely high (ideally infinite) because the gate is insulated from the channel.\n    **$Z_{in} \\approx \\infty$**\n\n*   **Output Impedance ($Z_{out}$):**\n    Looking into the source terminal, the impedance is low. It is roughly the parallel combination of the resistor $R_S$ and the inverse of the transconductance ($1/g_m$).\n    **$Z_{out} \\approx R_S \\parallel \\frac{1}{g_m} \\approx \\frac{1}{g_m}$** (assuming $R_S$ is large).\n\n### 4. Applications\nDue to its high input impedance and low output impedance, this circuit is primarily used as a **Voltage Buffer**.\n*   **Impedance Matching:** It can connect a high-impedance source (like a sensor or previous amplifier stage) to a low-impedance load (like a speaker or transmission line) without loading down the source.\n*   **Level Shifting:** It shifts the DC voltage level down by approximately $V_{GS}$.",
        "format": "markdown",
        "sha256": "d2077733cb5a4a521cb8459fb143f413cfcd3821f57b6e2eba716d93f328fe8e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain expression. The output-resistance discussion is also consistent with the circuit.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2506,
        "total_tokens": 3445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1750,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2506,
        "total_tokens": 3445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1750,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the configuration and its characteristics.\n\n### 1. Circuit Identification\n*   **Topology:** This circuit is a **Common Drain Amplifier**, widely known as a **Source Follower**.\n*   **Active Component:** The component labeled $M_1$ is an **N-channel MOSFET (NMOS)**. We can identify it as an NMOS because the arrow on the source terminal points outward (away from the channel). The broken vertical line indicates it is an enhancement-mode transistor.\n*   **Configuration:**\n    *   **Input ($V_{in}$):** Applied to the **Gate**.\n    *   **Output ($V_{out}$):** Taken from the **Source**.\n    *   **Drain:** Connected directly to the supply voltage $V_{DD}$ (which is an AC ground).\n\n### 2. Circuit Operation\nIn this configuration, the output voltage at the source \"follows\" the input voltage at the gate, hence the name \"Source Follower.\"\n\n*   **DC Analysis:** For the transistor to conduct, the gate-source voltage ($V_{GS}$) must be greater than the threshold voltage ($V_{th}$).\n    $$V_{GS} = V_{in} - V_{out}$$\n    Therefore, the output voltage is:\n    $$V_{out} = V_{in} - V_{GS}$$\n    Since $V_{GS}$ is relatively constant (typically around $V_{th}$ plus a small overdrive voltage), the DC output voltage is slightly lower than the input voltage. This circuit acts as a **level shifter**, shifting the voltage down by approximately $V_{GS}$.\n\n*   **AC Analysis (Small Signal):**\n    *   **Voltage Gain ($A_v$):** The voltage gain is slightly less than unity (1).\n        $$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m R_S}{1 + g_m R_S}$$\n        Where $g_m$ is the transconductance of the MOSFET. Since $g_m R_S$ is typically large, the fraction approaches 1.\n        $$A_v \\approx 1$$\n    *   **Phase:** The output is in phase with the input (non-inverting).\n\n### 3. Key Characteristics\n*   **High Input Impedance:** Looking into the gate of the MOSFET, the impedance is extremely high (ideally infinite) because the gate is insulated from the channel. This means the circuit draws negligible current from the input source.\n*   **Low Output Impedance:** Looking into the source terminal, the output impedance is low.\n    $$Z_{out} \\approx \\frac{1}{g_m} \\parallel R_S$$\n    This allows the circuit to drive low-impedance loads effectively.\n\n### 4. Applications\nDue to its high input impedance and low output impedance with a gain of approximately 1, this circuit is primarily used as a **Voltage Buffer**. It is used to isolate a high-impedance source (like a sensor or a previous amplifier stage) from a low-impedance load, preventing the load from affecting the source signal.",
        "format": "markdown",
        "sha256": "43265d31cda272826f9445b8eea584eace57e105be342a4cf496418aef4ca7de"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain, gm RS/(1 + gm RS). The supplementary output-resistance and buffer discussion is also consistent with the circuit.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2967,
        "total_tokens": 3906,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2278,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2967,
        "total_tokens": 3906,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2278,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-008-source-follower",
      "part": "part1",
      "question_number": 8,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-008-source-follower/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the configuration:\n\n### 1. Circuit Identification\nThis circuit is a **Common Drain Amplifier**, also widely known as a **Source Follower**.\n\n*   **Transistor ($M_1$):** It is an N-channel MOSFET (NMOS). We can identify this because the arrow on the source terminal points outward (away from the gate/channel).\n*   **Input ($V_{in}$):** Applied to the **Gate** of the transistor.\n*   **Output ($V_{out}$):** Taken from the **Source** of the transistor.\n*   **Drain:** Connected directly to the supply voltage $V_{DD}$ (which acts as an AC ground).\n*   **Resistor ($R_S$):** A source degeneration resistor connected between the source and ground.\n\n### 2. Operation Principle\nIn this configuration, the output voltage at the source \"follows\" the input voltage at the gate.\n*   When $V_{in}$ increases, the gate-to-source voltage ($V_{GS}$) increases, turning the transistor on harder.\n*   This increases the drain current ($I_D$), which flows through the resistor $R_S$.\n*   The increased current causes a larger voltage drop across $R_S$, raising $V_{out}$.\n*   As $V_{out}$ rises, it reduces the $V_{GS}$ (since $V_{GS} = V_{in} - V_{out}$), creating a negative feedback loop that stabilizes the circuit.\n\nThe relationship is approximately:\n$$V_{out} \\approx V_{in} - V_{GS(th)}$$\n(where $V_{GS(th)}$ is the threshold voltage plus a small overdrive voltage).\n\n### 3. Key Characteristics (Small-Signal Analysis)\n\n*   **Voltage Gain ($A_v$):**\n    The voltage gain is slightly less than unity (1).\n    $$A_v = \\frac{v_{out}}{v_{in}} = \\frac{g_m R_S}{1 + g_m R_S}$$\n    Since $g_m R_S$ is typically large, the fraction is close to 1. Therefore, $V_{out} \\approx V_{in}$.\n\n*   **Input Impedance ($Z_{in}$):**\n    Looking into the gate of a MOSFET, the impedance is extremely high (theoretically infinite at low frequencies) because the gate is insulated from the channel. This makes it an excellent load for previous stages.\n\n*   **Output Impedance ($Z_{out}$):**\n    Looking into the source terminal, the output impedance is low.\n    $$Z_{out} \\approx \\frac{1}{g_m} \\parallel R_S$$\n    This low output impedance allows the circuit to drive heavy loads.\n\n*   **Phase Shift:**\n    The output is in phase with the input (non-inverting amplifier).\n\n### 4. Applications\nDue to its high input impedance and low output impedance, this circuit is primarily used as a **Voltage Buffer**.\n*   **Impedance Matching:** It connects a high-impedance source (like a sensor or another amplifier stage) to a low-impedance load (like a speaker or a transmission line) without loading down the source.\n*   **Level Shifting:** It can be used to shift DC voltage levels down by the value of $V_{GS}$.",
        "format": "markdown",
        "sha256": "8952f2850153dcb41d614630385ce28204954af5962e22392f21db07bdf43824"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and gives its positive, less-than-unity gain as gm·RS/(1 + gm·RS). The supplemental output-resistance analysis is also consistent with the stated assumptions.",
          "golden_solution_sha256": "8f23ff232475a4bec79b12629414fe11fc7b9c6e9609b2ebcfc0e4ed2a0839d7",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2488,
        "total_tokens": 3427,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1749,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 939,
        "output_tokens": 2488,
        "total_tokens": 3427,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1749,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit's operation.\n\n### 1. Component Identification\n*   **$V_{DD}$**: The positive DC supply voltage rail.\n*   **$R_D$**: A resistor connected to the supply rail. In MOSFET circuits, this is typically the **Drain Resistor** or load resistor.\n*   **$M_1$**: An **NMOS transistor**. We can identify it as an NMOS because the arrow on the source terminal (the bottom terminal with the triangle) points outward/away from the channel, which is the standard symbol for an N-channel enhancement-mode MOSFET.\n*   **$V_{in}$**: The input voltage terminal.\n*   **$V_{out}$**: The output voltage terminal.\n\n### 2. Circuit Topology and Connections\nBy tracing the connections to the transistor $M_1$:\n*   **Gate (G)**: The terminal on the right (the isolated plate) is connected via a wire to the $V_{DD}$ rail. So, $V_G = V_{DD}$.\n*   **Drain (D)**: The top terminal is connected to the resistor $R_D$ and the output node $V_{out}$.\n*   **Source (S)**: The bottom terminal (with the arrow) is connected to the input $V_{in}$.\n\nThis configuration, where the input is applied to the Source, the output is taken from the Drain, and the Gate is held at a fixed potential (AC ground), is known as a **Common Gate Amplifier**.\n\n### 3. Circuit Analysis\n\n**DC Biasing and Operation:**\n*   The gate voltage is fixed at $V_{DD}$.\n*   The source voltage is $V_{in}$.\n*   The gate-to-source voltage is $V_{GS} = V_G - V_S = V_{DD} - V_{in}$.\n*   For the NMOS transistor to be turned ON (conducting current), we need $V_{GS} > V_{th}$ (threshold voltage). This implies $V_{DD} - V_{in} > V_{th}$, or **$V_{in} < V_{DD} - V_{th}$**.\n\n**Signal Behavior (Small Signal Analysis):**\n*   **Input-Output Relationship**:\n    *   If $V_{in}$ **increases**: The gate-to-source voltage $V_{GS}$ ($V_{DD} - V_{in}$) **decreases**.\n    *   A decrease in $V_{GS}$ causes the drain current $I_D$ to **decrease**.\n    *   The output voltage is given by $V_{out} = V_{DD} - I_D R_D$. Since $I_D$ decreases, the voltage drop across the resistor ($I_D R_D$) decreases.\n    *   Consequently, $V_{out}$ **increases** (moves closer to $V_{DD}$).\n*   **Gain**: Since an increase in input leads to an increase in output, this is a **non-inverting** amplifier. The small-signal voltage gain ($A_v$) is approximately $g_m R_D$ (where $g_m$ is the transconductance), which is positive.\n\n**Large Signal / Digital Behavior:**\n*   **If $V_{in}$ is Low (e.g., 0V)**: $V_{GS} = V_{DD}$, which is large. The transistor is strongly ON. Current flows from $V_{DD}$ through $R_D$ and the transistor to $V_{in}$. $V_{out}$ will be pulled down close to $V_{in}$ (assuming the transistor acts as a low resistance in the linear region).\n*   **If $V_{in}$ is High (e.g., $V_{DD}$)**: $V_{GS} = 0$. The transistor is OFF (cutoff). No current flows ($I_D \\approx 0$). There is no voltage drop across $R_D$, so $V_{out} = V_{DD}$.\n*   In this sense, the circuit acts as a **non-inverting buffer** (Low in $\\rightarrow$ Low out; High in $\\rightarrow$ High out).\n\n### Summary\nThe circuit is a **Common Gate NMOS amplifier** (or buffer). It features a **non-inverting** voltage gain, low input impedance (looking into the source), and is biased by tying the gate to the supply rail $V_{DD}$.",
        "format": "markdown",
        "sha256": "77dd1c259bc14338c04ab007037eb9023871e046283ee823bda3c9deef89c2f8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, AC-grounded gate, and common-gate topology, with the correct non-inverting gain and low input impedance. The informal “buffer” label and large-signal discussion do not undermine the essential analysis.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 10037,
        "total_tokens": 10942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9060,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 10037,
        "total_tokens": 10942,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9060,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Component Identification\n*   **$V_{DD}$**: This represents the positive DC power supply voltage.\n*   **$R_D$**: This is a resistor connected to the drain of the transistor, acting as a load resistor.\n*   **$M_1$**: This is an **N-channel MOSFET (NMOS)**. We can identify it as an NMOS because the arrow on the source terminal points inward towards the channel (indicating the direction from the p-type body to the n-type channel).\n*   **$V_{in}$**: The input voltage signal.\n*   **$V_{out}$**: The output voltage signal.\n\n### 2. Circuit Configuration\nBy tracing the connections, we can determine the configuration of the amplifier:\n*   **Gate (G):** Connected directly to $V_{DD}$. This fixes the gate at a constant DC potential. In AC analysis, $V_{DD}$ is considered an AC ground, so the gate is effectively grounded for signals.\n*   **Source (S):** Connected to the input signal $V_{in}$.\n*   **Drain (D):** Connected to the output $V_{out}$ and the resistor $R_D$.\n\nSince the input is applied to the source and the output is taken from the drain, with the gate being the common terminal (AC ground), this circuit is a **Common-Gate (CG) Amplifier**.\n\n### 3. Circuit Operation & Analysis\n\n**DC Biasing:**\nFor the NMOS transistor $M_1$ to be turned ON (conducting current), the Gate-Source voltage ($V_{GS}$) must be greater than the threshold voltage ($V_{th}$).\n$$V_{GS} = V_{Gate} - V_{Source} = V_{DD} - V_{in}$$\nSo, the condition for conduction is:\n$$V_{DD} - V_{in} > V_{th} \\quad \\Rightarrow \\quad V_{in} < V_{DD} - V_{th}$$\nThis means the input voltage $V_{in}$ must be sufficiently lower than the supply voltage for the transistor to operate.\n\n**Signal Behavior (Qualitative):**\n1.  If the input voltage **$V_{in}$ increases**:\n    *   The Gate-Source voltage $V_{GS}$ ($V_{DD} - V_{in}$) **decreases**.\n    *   This causes the drain current $I_D$ flowing through the transistor to **decrease**.\n    *   The voltage drop across the resistor $R_D$ ($V_{R_D} = I_D \\cdot R_D$) **decreases**.\n    *   Since $V_{out} = V_{DD} - V_{R_D}$, a smaller voltage drop means **$V_{out}$ increases**.\n2.  Conversely, if **$V_{in}$ decreases**, **$V_{out}$ decreases**.\n\n**Conclusion:** The output voltage moves in the same direction as the input voltage. Therefore, this is a **non-inverting amplifier**.\n\n### 4. Key Characteristics (Small-Signal Model)\n*   **Voltage Gain ($A_v$):** The voltage gain is positive and approximately equal to $g_m R_D$ (where $g_m$ is the transconductance of the transistor).\n    $$A_v \\approx g_m R_D$$\n*   **Input Impedance ($R_{in}$):** The input impedance looking into the source is low, approximately $1/g_m$. This makes it suitable for matching low-impedance sources.\n*   **Output Impedance ($R_{out}$):** The output impedance is relatively high, approximately equal to $R_D$ (ignoring the transistor's output resistance $r_o$).\n*   **Current Gain:** The current gain is approximately unity ($1$). It acts as a **current buffer**, taking a current from a low-impedance source and delivering it to a high-impedance load.\n\n### Summary\nThis circuit is a **Common-Gate NMOS Amplifier**. It provides non-inverting voltage gain, has low input impedance, and is often used in high-frequency applications (because it avoids the Miller effect capacitance multiplication) or as a current buffer in cascode configurations.",
        "format": "markdown",
        "sha256": "f17938b1c043c8c62b096b15cdf33bc9de66a023f92cad4d8e46ad26d7c38f1a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-driven common-gate topology, explains the non-inverting response, and gives the key approximations Rin ≈ 1/gm and Av ≈ +gmRD. The additional bias and application comments do not undermine the essential analysis.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 7778,
        "total_tokens": 8683,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6848,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 7778,
        "total_tokens": 8683,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6848,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-009-common-gate-source-input",
      "part": "part1",
      "question_number": 9,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-009-common-gate-source-input/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the configuration, components, and operation.\n\n### 1. Circuit Identification\nThis circuit is a **Common Gate Amplifier** (also known as a Common Gate Stage).\n\n*   **Input ($V_{in}$):** Applied to the **Source** terminal of the transistor.\n*   **Output ($V_{out}$):** Taken from the **Drain** terminal.\n*   **Gate:** Connected to the supply voltage $V_{DD}$. In AC analysis, a DC voltage source is considered a ground, so the Gate is at **AC ground**. This confirms the \"Common Gate\" configuration.\n\n### 2. Component Analysis\n*   **$M_1$ (MOSFET):**\n    *   The symbol shows a transistor with the gate isolated from the channel.\n    *   **Terminal Identification:** The terminal with the arrow is the Source (connected to $V_{in}$). The terminal connected to the resistor $R_D$ is the Drain. The terminal connected to the right vertical line (going to $V_{DD}$) is the Gate.\n    *   **Type:** Although the arrow pointing inward typically denotes a PMOS in some simplified symbols (or the bulk connection in NMOS), for this circuit to function as a standard amplifier with $V_{in} < V_{DD}$, $M_1$ is most likely an **NMOS transistor**.\n        *   *Reasoning:* For an NMOS, $V_{GS} = V_{Gate} - V_{Source} = V_{DD} - V_{in}$. If $V_{in}$ is lower than $V_{DD}$, $V_{GS}$ is positive, turning the transistor ON. If it were a PMOS, with Gate at $V_{DD}$ and Source at $V_{in}$ (where $V_{in} < V_{DD}$), the transistor would be turned OFF ($V_{SG} < 0$).\n*   **$R_D$:** This is the **Drain Resistor** (or load resistor). It converts the drain current into an output voltage.\n*   **$V_{DD}$:** The positive DC supply voltage.\n\n### 3. Circuit Operation (Qualitative)\nAssuming $M_1$ is an NMOS transistor:\n1.  **Biasing:** The Gate is held at a constant high voltage ($V_{DD}$).\n2.  **Input Effect:** When the input voltage $V_{in}$ (at the Source) **increases**:\n    *   The Gate-Source voltage $V_{GS} = V_{DD} - V_{in}$ **decreases**.\n    *   A lower $V_{GS}$ causes the drain current $I_D$ flowing through the transistor to **decrease**.\n3.  **Output Effect:** The output voltage is determined by the voltage drop across the resistor: $V_{out} = V_{DD} - I_D R_D$.\n    *   Since the current $I_D$ decreases, the voltage drop across $R_D$ ($I_D R_D$) decreases.\n    *   Therefore, $V_{out}$ **increases** (moves closer to $V_{DD}$).\n4.  **Conclusion:** An increase in input leads to an increase in output. This is a **non-inverting amplifier**.\n\n### 4. Small-Signal Characteristics\nFor small AC signals, the circuit has the following properties:\n\n*   **Voltage Gain ($A_v$):**\n    The voltage gain is positive (non-inverting) and is approximately:\n    $$A_v = \\frac{v_{out}}{v_{in}} \\approx g_m R_D$$\n    *(where $g_m$ is the transconductance of the MOSFET)*.\n\n*   **Input Impedance ($R_{in}$):**\n    Looking into the source terminal, the input impedance is low:\n    $$R_{in} \\approx \\frac{1}{g_m}$$\n    This makes the circuit suitable for matching low-impedance sources (like a current source).\n\n*   **Output Impedance ($R_{out}$):**\n    Looking into the drain terminal, the output impedance is relatively high, dominated by the resistor $R_D$ (in parallel with the transistor's output resistance $r_o$):\n    $$R_{out} \\approx R_D$$\n\n### 5. Applications\nThis Common Gate configuration is frequently used in:\n*   **High-frequency amplifiers:** Because the input and output are isolated by the grounded gate, there is no Miller effect (capacitive feedback from output to input is minimized), allowing for better high-frequency response.\n*   **Current Buffers:** Due to its low input impedance and high output impedance, it can accept a current signal at the input and deliver it to a high-impedance load at the output.\n*   **Cascode Amplifiers:** It is often stacked on top of a Common Source amplifier to improve gain and bandwidth.",
        "format": "markdown",
        "sha256": "354d4be7f657c1e9474f661c1c45c5619ca24720177b4d12350350b406552954"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-input common-gate stage, gate AC ground, low input resistance near 1/gm, and positive gain near gmRD. The output-resistance approximation and extra application comments do not affect the essential analysis.",
          "golden_solution_sha256": "1b3a848197667846074404db3b3d8871ff2129384f8d686f3624e0319ea90d69",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 9769,
        "total_tokens": 10674,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 905,
        "output_tokens": 9769,
        "total_tokens": 10674,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit topology.\n\n### 1. Component Identification\n*   **$M_1$**: A MOSFET transistor. Based on the standard orientation where the drain is connected to the positive supply ($V_{DD}$) and the source is towards the ground, this is likely an **NMOS** transistor. The arrow on the source terminal pointing inward is a symbol convention sometimes used for PMOS, but in the context of this topology (Drain to $V_{DD}$), it functions as an NMOS in a standard amplifier configuration. (Note: If it were a PMOS, the source would typically be at the top connected to $V_{DD}$).\n*   **$R_D$**: A drain resistor connected between the supply voltage $V_{DD}$ and the drain of the transistor. It acts as the load resistor, converting the drain current changes into voltage changes at the output.\n*   **$C_1$**: A coupling capacitor. It blocks DC components from the input source $V_{in}$ while allowing AC signals to pass through to the circuit.\n*   **$V_{DD}$**: The positive DC power supply rail.\n*   **$V_b$**: A DC bias voltage connected to the gate of the transistor. This sets the operating point (quiescent point) of the transistor. Since it is a constant DC voltage, it acts as an **AC ground**.\n*   **$V_{in}$**: The AC input voltage source.\n*   **$V_{out}$**: The output voltage node, taken from the drain of the transistor.\n\n### 2. Circuit Topology: Common Gate Amplifier\nThe circuit configuration is characteristic of a **Common Gate (CG) Amplifier**. Here's why:\n*   **Gate**: The gate terminal is connected to a fixed DC bias voltage $V_b$. For AC signal analysis, a constant DC voltage source is considered a short to ground. Therefore, the gate is at **AC ground**. This is the \"Common\" terminal.\n*   **Input**: The input signal $V_{in}$ is coupled via capacitor $C_1$ to the **Source** terminal of the transistor.\n*   **Output**: The output $V_{out}$ is taken from the **Drain** terminal.\n\n### 3. Circuit Analysis & Anomaly\nThere is a significant detail in the schematic that affects the analysis: **The source terminal is connected directly to ground.**\n\n**Literal Interpretation (As Drawn):**\n*   The source of the transistor is hard-wired to ground ($V_S = 0$).\n*   The input $V_{in}$ is connected via $C_1$ to this grounded node. This means the AC input signal is effectively shorted to ground.\n*   The gate is at a fixed potential $V_b$.\n*   Since $V_S = 0$ and $V_G = V_b$, the gate-source voltage $V_{GS} = V_b$ is constant.\n*   Consequently, the drain current $I_D$ is constant, and the output voltage $V_{out} = V_{DD} - I_D R_D$ is a constant DC value.\n*   **Result**: The circuit would have **zero voltage gain** for the signal $V_{in}$. The input signal does not modulate the transistor.\n\n**Intended Interpretation (Standard Common Gate Stage):**\nIn textbook examples of a Common Gate amplifier, the source is usually connected to a **current source** (or a large resistor) that goes to ground, rather than a direct short. This bias element sets the DC current but presents a high impedance to the AC signal, allowing the input voltage $V_{in}$ to modulate the source voltage.\n\nAssuming the ground symbol at the bottom represents a bias current source (which is an open circuit for AC signals) or is a drawing simplification for the negative rail with an implicit impedance:\n\n*   **DC Analysis**:\n    *   The transistor is biased by $V_b$. Assuming it's in saturation, $I_D = \\frac{1}{2} \\mu_n C_{ox} \\frac{W}{L} (V_b - V_{TH})^2$ (assuming source is at approx 0V DC).\n    *   $V_{out, DC} = V_{DD} - I_D R_D$.\n\n*   **AC Small-Signal Analysis**:\n    *   The gate is grounded ($v_g = 0$).\n    *   The input signal $v_{in}$ is applied to the source ($v_s = v_{in}$).\n    *   The gate-source voltage is $v_{gs} = v_g - v_s = 0 - v_{in} = -v_{in}$.\n    *   The drain current is $i_d = g_m v_{gs} = -g_m v_{in}$.\n    *   The output voltage is $v_{out} = -i_d R_D = -(-g_m v_{in}) R_D = g_m R_D v_{in}$.\n\n**Key Characteristics (assuming functional Common Gate topology):**\n*   **Voltage Gain ($A_v$)**: $A_v = \\frac{v_{out}}{v_{in}} \\approx g_m R_D$. The gain is **positive**, meaning the output is **non-inverting** (in phase with the input).\n*   **Input Impedance ($R_{in}$)**: Looking into the source, the impedance is low, approximately $1/g_m$.\n*   **Output Impedance ($R_{out}$)**: Looking into the drain, the impedance is high, approximately $R_D$ (ignoring the transistor's output resistance $r_o$).\n*   **Application**: Common gate amplifiers are often used for their good high-frequency response (due to the absence of the Miller effect) and as current buffers (low input impedance, high output impedance).",
        "format": "markdown",
        "sha256": "aab241aa9390887fc6bd626840c0da3f8df3c064fc8d4d397262bf58e54f52ae"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly identifies that the source is hard-shorted to ground, so the input is shorted and the as-drawn circuit has ideally zero gain. The common-gate gain discussion is explicitly conditional on a different, functional topology.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 13736,
        "total_tokens": 15192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12458,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 13736,
        "total_tokens": 15192,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12458,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the configuration and its operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **Common Gate (CG) Amplifier**.\n\n*   **Transistor ($M_1$):** Based on the topology (Drain connected towards the positive supply $V_{DD}$ and Source connected towards ground), $M_1$ is an **NMOS transistor**. Although the arrow symbol can vary by convention, in this configuration (Source at the bottom, Drain at the top), it functions as an NMOS.\n*   **Input:** The input signal $V_{\\text{in}}$ is applied to the **Source** terminal of the transistor through the coupling capacitor $C_1$.\n*   **Output:** The output voltage $V_{\\text{out}}$ is taken from the **Drain** terminal.\n*   **Gate:** The Gate is connected to a fixed DC bias voltage $V_b$. In AC analysis, a fixed DC voltage source acts as an AC ground. Since the input is at the source and output is at the drain, and the gate is common (grounded for AC), this confirms the **Common Gate** topology.\n\n### 2. DC Analysis (Biasing)\n*   **Capacitor $C_1$:** Acts as an open circuit for DC signals.\n*   **Source Terminal:** The source of $M_1$ is connected directly to ground (indicated by the ground symbol below the transistor node). Therefore, the DC source voltage $V_S = 0\\text{ V}$.\n*   **Gate Terminal:** The gate is held at a constant bias voltage $V_b$. For the NMOS transistor to be turned on and operating in the saturation region, we must have $V_b > V_{\\text{TH}}$ (where $V_{\\text{TH}}$ is the threshold voltage).\n*   **Drain Current ($I_D$):** The transistor conducts a DC current determined by the overdrive voltage:\n    $$I_D = \\frac{1}{2} \\mu_n C_{\\text{ox}} \\frac{W}{L} (V_b - V_{\\text{TH}})^2$$\n*   **Output DC Voltage ($V_{\\text{out, DC}}$):** The DC voltage at the output is determined by the voltage drop across the drain resistor $R_D$:\n    $$V_{\\text{out, DC}} = V_{DD} - I_D R_D$$\n\n### 3. AC Analysis (Small Signal)\n*   **Capacitor $C_1$:** Acts as a short circuit for AC signals (assuming the frequency is high enough).\n*   **Power Supply $V_{DD}$:** Acts as an AC ground.\n*   **Signal Path:**\n    *   The input voltage $v_{\\text{in}}$ appears at the source terminal ($v_s = v_{\\text{in}}$). *Note: The schematic shows a direct ground connection at the source node. In a practical Common Gate amplifier, this ground would typically be a current source or resistor to set the bias, and the input would drive the node. If the source is hard-grounded as drawn, the AC input would be shorted to ground. Assuming standard Common Gate operation where the input modulates the source voltage:*\n    *   The gate is at AC ground ($v_g = 0$).\n    *   The gate-to-source voltage is $v_{gs} = v_g - v_s = 0 - v_{\\text{in}} = -v_{\\text{in}}$.\n*   **Voltage Gain ($A_v$):**\n    The small-signal drain current is $i_d = g_m v_{gs} = -g_m v_{\\text{in}}$.\n    This current flows from the drain to the source. At the output node (Drain), the current flows down through the transistor, which means it is drawn from the resistor $R_D$ (connected to AC ground).\n    $$v_{\\text{out}} = -i_d R_D = -(-g_m v_{\\text{in}}) R_D = g_m R_D v_{\\text{in}}$$\n    $$A_v = \\frac{v_{\\text{out}}}{v_{\\text{in}}} = g_m R_D$$\n    *(Ignoring channel length modulation $r_o$)*.\n    The gain is **positive**, meaning the output is **in-phase** with the input. This is a characteristic feature of Common Gate amplifiers.\n\n### 4. Impedance Characteristics\n*   **Input Impedance ($R_{\\text{in}}$):** Looking into the source terminal, the impedance is low, approximately $1/g_m$. This makes it suitable for matching low-impedance sources (like cables).\n*   **Output Impedance ($R_{\\text{out}}$):** Looking into the drain terminal, the impedance is high, approximately $R_D$ (or $R_D \\parallel r_o$ if considering transistor output resistance).\n\n### Summary\nThis is a **Common Gate NMOS Amplifier**. It provides a non-inverting voltage gain of approximately $g_m R_D$, has a low input impedance, and a relatively high output impedance. It is often used for high-frequency applications or as a current buffer.\n\n*(Note on the schematic: The direct ground connection at the source node alongside the input capacitor $C_1$ is technically a short circuit for the AC input signal in an ideal schematic. In a functional circuit, that ground connection would typically be replaced by a bias current source or resistor, or the input $V_{\\text{in}}$ would be connected directly without the capacitor if the source was meant to be grounded for DC but driven by a current source.)*",
        "format": "markdown",
        "sha256": "44e9b3688dbbed190774700071d6dd9e14de404fbe47a3d0454465111697775d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly notices that the source is directly grounded and even states that this shorts the AC input, but then analyzes the circuit as if that short were absent and concludes the gain is approximately gmRD. The ideal gain as drawn is zero.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 15681,
        "total_tokens": 17137,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14436,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 15681,
        "total_tokens": 17137,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14436,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-010-source-input-shorted-to-ground",
      "part": "part1",
      "question_number": 10,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-010-source-input-shorted-to-ground/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the configuration, components, and operation.\n\n### 1. Circuit Identification and Topology\nThe circuit shown is a **MOSFET Amplifier**. Specifically, the topology resembles a **Common Gate Amplifier**.\n\n*   **Input ($V_{in}$)**: The input signal is coupled via capacitor $C_1$ to the **Source** terminal of the transistor $M_1$ (the bottom terminal with the arrow).\n*   **Output ($V_{out}$)**: The output is taken from the **Drain** terminal (the top terminal connected to $R_D$).\n*   **Gate ($V_b$)**: The Gate is connected to a fixed DC bias voltage $V_b$. In AC analysis, a fixed DC voltage source acts as an AC ground.\n\nSince the input is applied to the source, the output is taken from the drain, and the gate is common (at AC ground), this is the structure of a **Common Gate** configuration.\n\n### 2. Component Analysis\n*   **$M_1$**: This is a MOSFET.\n    *   *Symbol Note*: The arrow on the source terminal points inward towards the channel. In many standard conventions (like Razavi), this indicates a **PMOS** transistor. However, the biasing connections (Drain to positive $V_{DD}$, Source to Ground) are typical for an **NMOS** transistor. For a PMOS to operate normally, the Source should be at the highest potential ($V_{DD}$). Assuming standard operation with a positive supply $V_{DD}$, it is highly likely that $M_1$ is intended to be an **NMOS** transistor (where the arrow might represent the bulk connection or is drawn in a specific style). The analysis below assumes an NMOS for functional consistency.\n*   **$R_D$**: Drain resistor. It acts as the load resistor, converting the drain current into an output voltage.\n*   **$C_1$**: Coupling capacitor. It blocks DC components from the input source $V_{in}$ while allowing AC signals to pass.\n*   **$V_{DD}$**: Positive DC supply voltage.\n*   **$V_b$**: Gate bias voltage. It sets the DC operating point of the transistor.\n\n### 3. DC Analysis (Bias Point)\n*   The capacitor $C_1$ acts as an open circuit for DC signals.\n*   The Source terminal of $M_1$ is connected directly to ground (indicated by the ground symbol at the bottom center). Therefore, $V_S = 0$ V.\n*   The Gate voltage is $V_G = V_b$.\n*   The Gate-Source voltage is $V_{GS} = V_b - 0 = V_b$.\n*   Assuming $V_b > V_{th}$ (threshold voltage), the transistor is turned ON and operates in the saturation region (typically desired for amplifiers).\n*   The drain current $I_D$ is determined by the transistor parameters and $V_{GS}$.\n*   The output DC voltage is:\n    $$V_{out} = V_{DD} - I_D R_D$$\n\n### 4. AC Analysis (Small Signal)\n**As drawn in the schematic:**\nThere is a critical issue with the schematic as drawn. The Source terminal is connected directly to ground.\n*   The input $V_{in}$ is connected via $C_1$ to the Source node.\n*   Since the Source node is grounded, the AC input signal is effectively shorted to ground.\n*   The source voltage $v_s$ remains 0 V (AC ground).\n*   The gate voltage $v_g$ is 0 V (AC ground, since $V_b$ is DC).\n*   Therefore, $v_{gs} = v_g - v_s = 0$.\n*   The transistor generates no AC current, and the voltage gain is **zero**.\n\n**Intended Function (Common Gate Amplifier):**\nIt is highly likely that this diagram is intended to represent a functional **Common Gate Amplifier**, where the ground symbol at the source node represents a high-impedance current source (tail current) or the input is meant to drive the source directly without a short to ground. Assuming a functional Common Gate stage:\n\n*   **Signal Path**: The input $v_{in}$ appears at the source ($v_s = v_{in}$). The gate is at AC ground ($v_g = 0$).\n*   **Gate-Source Voltage**: $v_{gs} = v_g - v_s = 0 - v_{in} = -v_{in}$.\n*   **Drain Current**: $i_d = g_m v_{gs} = -g_m v_{in}$.\n*   **Output Voltage**: $v_{out} = -i_d R_D = -(-g_m v_{in}) R_D = g_m R_D v_{in}$.\n*   **Voltage Gain ($A_v$)**:\n    $$A_v = \\frac{v_{out}}{v_{in}} = g_m R_D$$\n    The gain is positive, meaning the Common Gate amplifier is **non-inverting**.\n\n*   **Input Impedance ($R_{in}$)**: Looking into the source terminal, the impedance is low, approximately $1/g_m$.\n*   **Output Impedance ($R_{out}$)**: Looking into the drain terminal, the impedance is approximately $R_D$ (or $R_D || r_o$ considering channel length modulation).\n\n### Summary\nThe circuit is a **Common Gate Amplifier** topology.\n*   **DC Bias**: Sets the transistor in saturation with $V_{GS} = V_b$.\n*   **AC Gain**: Ideally $g_m R_D$ (non-inverting).\n*   **Note**: As strictly drawn, the source is shorted to ground, which would short out the input signal and result in zero gain. For the circuit to work as an amplifier, the connection from the source node to ground should be a current source or resistor, not a direct short, or the input should be applied differently.",
        "format": "markdown",
        "sha256": "076b045b48777c7b741f2ac8d7fc3c2b7bf26b4a8aa9d9fc4ad9d4cd94bafbe0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It explicitly notices that the source is hard-shorted to ground and concludes that the input is shorted, giving ideally zero gain as drawn. Its separate discussion of the intended common-gate stage does not alter that correct conclusion.",
          "golden_solution_sha256": "4fa501e147a166a71d6aa33565bbe693318d65c0c8c788e7a5087eb13c71d3ea",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 17828,
        "total_tokens": 19284,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16502,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1456,
        "output_tokens": 17828,
        "total_tokens": 19284,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16502,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, we can determine the number of poles by analyzing the independent energy storage elements (capacitors) in the small-signal model.\n\n1.  **Identify the capacitors:** The circuit contains four capacitors: $C_{GS}$, $C_{GD}$, $C_{DB}$, and $C_{SB}$.\n2.  **Analyze the connections:**\n    *   The MOSFET $M_1$ is in a common-source configuration because its source terminal is connected directly to ground.\n    *   **$C_{GS}$**: Connected between the gate and the source (ground). This capacitor is active.\n    *   **$C_{GD}$**: Connected between the gate and the drain. This capacitor is active and provides feedback.\n    *   **$C_{DB}$**: Connected between the drain and the bulk/substrate (ground). This capacitor is active.\n    *   **$C_{SB}$**: Connected between the source and the bulk/substrate. Since the source is connected to ground and the bottom of the capacitor is connected to ground, this capacitor is shorted out (connected between ground and ground). It does not affect the circuit dynamics and does not contribute a pole.\n3.  **Determine the number of independent state variables:**\n    *   We have three active capacitors: $C_{GS}$, $C_{GD}$, and $C_{DB}$.\n    *   These capacitors form a loop: Ground $\\rightarrow$ $C_{GS}$ $\\rightarrow$ Gate Node $\\rightarrow$ $C_{GD}$ $\\rightarrow$ Drain Node $\\rightarrow$ $C_{DB}$ $\\rightarrow$ Ground.\n    *   Because of this capacitor loop, the voltages across the capacitors are not all independent. Specifically, the voltage across $C_{GD}$ is the difference between the voltage across $C_{GS}$ (gate voltage) and the voltage across $C_{DB}$ (drain voltage).\n    *   The number of poles is equal to the number of independent energy storage elements. With 3 capacitors and 1 independent loop constraint, the number of poles is $3 - 1 = 2$.\n\nAlternatively, performing nodal analysis at the Gate and Drain nodes yields a system of two first-order differential equations, which results in a second-order characteristic equation (denominator of the transfer function). A second-order system has **2 poles**.\n\n**Answer:** The circuit has **2** poles.",
        "format": "markdown",
        "sha256": "06fb3d2095f063c6af0f3221f0af05a3c2e95d4ad9d82986f72be9a52e0cfef7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes there are two poles and justifies this by noting that CSB is shorted out and the three remaining capacitor voltages have only two independent degrees of freedom.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 4404,
        "total_tokens": 5976,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3875,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 4404,
        "total_tokens": 5976,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3875,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, we can determine the number of poles by analyzing the independent energy storage elements (capacitors) and the circuit topology.\n\n1.  **Identify the circuit configuration:** The circuit is a Common-Source amplifier using an NMOS transistor ($M_1$). The input is applied to the gate through a resistor $R_S$, and the output is taken from the drain. The source terminal is connected directly to ground.\n\n2.  **Identify the capacitors:**\n    *   $C_{GS}$: Connected between the gate and ground (since the source is grounded).\n    *   $C_{GD}$: Connected between the gate and the drain (feedback capacitor).\n    *   $C_{DB}$: Connected between the drain and ground (assuming the bulk is grounded).\n    *   $C_{SB}$: Connected between the source and ground. Since the source is already connected directly to ground, this capacitor is shorted out (connected from ground to ground) and does not affect the circuit's frequency response.\n\n3.  **Determine the number of independent nodes:**\n    The circuit has two main dynamic nodes where voltage can vary with frequency:\n    *   **Node 1 (Gate):** The junction of $R_S$, $C_{GS}$, $C_{GD}$, and the gate of $M_1$.\n    *   **Node 2 (Drain/Output):** The junction of $R_D$, $C_{GD}$, $C_{DB}$, and the drain of $M_1$.\n\n4.  **Calculate the number of poles:**\n    Although there are three active capacitors ($C_{GS}$, $C_{GD}$, $C_{DB}$), they form a loop (Gate $\\rightarrow$ Drain $\\rightarrow$ Ground $\\rightarrow$ Gate). In circuit theory, a loop consisting entirely of capacitors reduces the number of independent state variables by one.\n    Alternatively, using nodal analysis, we would write KCL equations for the Gate node and the Drain node. This results in a system of two linear equations, leading to a characteristic polynomial of degree 2 (a quadratic equation in $s$).\n\n    Therefore, the transfer function will have a denominator of the form $as^2 + bs + c$, which corresponds to **2 poles**.\n\n**Answer:** The circuit has **2** poles.",
        "format": "markdown",
        "sha256": "4fb89b3500828e9fba4e330877da5ebb23ad794b37726c1c698151d46d23d080"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that CSB is shorted because the source is grounded, and that CGS, CGD, and CDB yield only two independent capacitor voltages, so the circuit has two poles.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 5179,
        "total_tokens": 6751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4672,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 5179,
        "total_tokens": 6751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4672,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-011-many-poles-have",
      "part": "part1",
      "question_number": 11,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-011-many-poles-have/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the step-by-step determination of the number of poles:\n\n1.  **Identify Energy Storage Elements:** The circuit contains capacitors which are energy storage elements. The capacitors shown are $C_{GS}$, $C_{GD}$, $C_{DB}$, and $C_{SB}$.\n2.  **Analyze Circuit Connections:**\n    *   The source of the MOSFET $M_1$ is connected directly to ground.\n    *   The capacitor $C_{SB}$ is connected from the source node to ground. Since the source is already at ground potential, $C_{SB}$ is shorted out and does not affect the circuit's dynamic behavior.\n    *   This leaves three active capacitors: $C_{GS}$ (gate-to-source/ground), $C_{GD}$ (gate-to-drain), and $C_{DB}$ (drain-to-bulk/ground).\n3.  **Determine Independent Nodes:** The circuit has two main dynamic nodes where voltage can vary with time due to the capacitors:\n    *   **The Gate Node:** Connected to $R_S$, $C_{GS}$, and $C_{GD}$.\n    *   **The Drain Node (Output):** Connected to $R_D$, $C_{GD}$, and $C_{DB}$.\n4.  **Count Poles:**\n    *   Generally, the number of poles corresponds to the number of independent energy storage elements.\n    *   While there are 3 capacitors ($C_{GS}, C_{GD}, C_{DB}$), they form a loop (Gate $\\rightarrow$ Drain $\\rightarrow$ Ground $\\rightarrow$ Gate). In circuit theory, a loop consisting only of capacitors reduces the number of independent state variables by one.\n    *   Alternatively, using nodal analysis, we can write KCL equations for the Gate node ($V_g$) and the Drain node ($V_d$). This results in a system of two linear differential equations. The characteristic equation (denominator of the transfer function) will be a second-order polynomial in $s$ (i.e., $as^2 + bs + c = 0$).\n    *   A second-order system has **2 poles**.\n\nTherefore, the circuit has **2** poles.",
        "format": "markdown",
        "sha256": "6378bf32873c7b47c707964cecebd12f0ed86e4f0d4fd89e166ab1abdce28206"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies that CSB is shorted because the source is grounded, and that CGS, CGD, and CDB form a capacitor loop with only two independent state variables, yielding two poles.",
          "golden_solution_sha256": "d6e2d72c604ae3c83e7b25306ecb7ec85736574c7dd1a3f26a206b697a6dabfe",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 3179,
        "total_tokens": 4751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2687,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1572,
        "output_tokens": 3179,
        "total_tokens": 4751,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2687,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification\nThe circuit shown is a **MOSFET Amplifier**, specifically configured as a **Common Gate (CG) Amplifier** with a feedback biasing network.\n\n### 2. Component Breakdown\n*   **$M_1$**: An N-channel MOSFET (NMOS). The symbol indicates the source terminal is at the bottom (connected to $V_{in}$) and the drain terminal is at the top.\n*   **$R_D$**: The drain load resistor, connected between the power supply ($V_{DD}$) and the drain of the transistor.\n*   **$R_1$ and $R_2$**: Resistors forming a voltage divider network connected to the gate of the transistor.\n*   **$V_{DD}$**: The DC power supply voltage.\n*   **$V_{in}$**: The input signal terminal, connected to the source of the MOSFET.\n*   **$V_{out}$**: The output signal terminal, connected to the drain of the MOSFET.\n*   **Ground**: The reference potential at the bottom of the circuit.\n\n### 3. Circuit Configuration: Common Gate\nThe topology is identified as a **Common Gate** configuration because:\n*   **Input ($V_{in}$)** is applied to the **Source** terminal.\n*   **Output ($V_{out}$)** is taken from the **Drain** terminal.\n*   The **Gate** terminal is the common reference point (though in this specific circuit, it's not directly grounded but biased via a network).\n\n### 4. Biasing and Feedback Analysis\nThe gate of the MOSFET is not connected to a fixed DC voltage source. Instead, it is biased using a feedback network consisting of $R_1$ and $R_2$.\n*   **Voltage Divider:** Resistors $R_1$ and $R_2$ form a divider between the output node (Drain) and Ground.\n*   **Gate Voltage ($V_G$):** The voltage at the gate is determined by the output voltage:\n    $$V_G = V_{out} \\cdot \\frac{R_2}{R_1 + R_2}$$\n*   **Negative Feedback (DC Stability):** This configuration provides negative feedback to stabilize the DC operating point (Q-point).\n    *   If the drain current ($I_D$) increases (due to temperature or component variation), the voltage drop across $R_D$ increases.\n    *   This causes the output voltage ($V_{out} = V_{DD} - I_D R_D$) to decrease.\n    *   Consequently, the gate voltage ($V_G$) decreases.\n    *   Since the source voltage is fixed (by the DC component of $V_{in}$), the gate-to-source voltage ($V_{GS} = V_G - V_S$) decreases.\n    *   A lower $V_{GS}$ reduces the drain current $I_D$, counteracting the initial increase. This makes the bias point stable.\n\n### 5. Operational Characteristics\n*   **Voltage Gain:** The Common Gate amplifier is a **non-inverting** amplifier. An increase in source voltage ($V_{in}$) decreases $V_{GS}$ (since $V_{GS} = V_G - V_{in}$), which decreases $I_D$. A decrease in $I_D$ leads to a smaller voltage drop across $R_D$, causing $V_{out}$ to rise. Thus, $V_{in}$ and $V_{out}$ are in phase.\n*   **Input Impedance:** Common gate amplifiers typically have a **low input impedance** (looking into the source), which is approximately $1/g_m$ (where $g_m$ is the transconductance). The feedback network will modify this value.\n*   **Output Impedance:** The output impedance is relatively high, primarily determined by $R_D$ in parallel with the output resistance of the transistor ($r_o$).\n*   **Frequency Response:** Common gate configurations are known for good high-frequency performance because they do not suffer from the Miller effect (capacitive multiplication) that limits Common Source amplifiers.\n\n### Summary\nThis circuit is a **self-biased Common Gate MOSFET amplifier**. It takes an input signal at the source, amplifies it without inverting the phase, and outputs it at the drain. The resistors $R_1$ and $R_2$ provide a feedback mechanism that stabilizes the DC operating point of the transistor.",
        "format": "markdown",
        "sha256": "870e4cc1d2bab27479e38b073cabe091fab065604d5815dde09cec4b6d2cbfcf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-to-gate divider feedback, and negative feedback, and recognizes the non-inverting response. The full-credit rule does not require a closed-loop gain expression; the peripheral impedance and frequency-response comments do not undermine the essential analysis.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 8499,
        "total_tokens": 9840,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7518,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 8499,
        "total_tokens": 9840,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7518,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components, topology, and operation.\n\n### 1. Component Identification\n*   **$M_1$**: An N-channel MOSFET (NMOS). The terminal connected to $V_{in}$ is the **Source**, the terminal connected to the output node is the **Drain**, and the terminal connected to the resistor network is the **Gate**.\n*   **$R_D$**: A drain resistor connected to the power supply $V_{DD}$. It acts as the load resistor for the amplifier.\n*   **$R_1$ and $R_2$**: These resistors form a voltage divider network. They provide bias to the Gate and create a feedback loop from the output to the input.\n*   **$V_{DD}$**: The DC power supply voltage.\n*   **$V_{in}$**: The input signal, applied to the Source of the MOSFET.\n*   **$V_{out}$**: The output signal, taken from the Drain of the MOSFET.\n\n### 2. Circuit Topology\nThis circuit is configured as a **Common-Gate Amplifier** with **negative feedback**.\n*   **Input**: Applied to the Source ($V_{in}$).\n*   **Output**: Taken from the Drain ($V_{out}$).\n*   **Common Terminal**: The Gate is the common terminal in a standard Common-Gate setup, but here it is not grounded. Instead, it is held at a potential determined by the feedback network.\n\nSpecifically, this topology mimics a **Non-Inverting Operational Amplifier** circuit.\n*   The Source acts like the non-inverting input (+) of an op-amp.\n*   The Gate acts like the inverting input (-) of an op-amp.\n*   The resistors $R_1$ and $R_2$ form the feedback network similar to the gain-setting resistors in a non-inverting op-amp configuration.\n\n### 3. Operation Analysis\n\n**DC Biasing (Operating Point):**\nThe resistors $R_1$ and $R_2$ provide a self-biasing mechanism. The voltage at the Gate ($V_G$) is a fraction of the Drain voltage ($V_D$ or $V_{out}$):\n$$V_G = V_{out} \\cdot \\frac{R_2}{R_1 + R_2}$$\nThis creates negative feedback that stabilizes the DC operating point. If the drain current $I_D$ increases, the voltage drop across $R_D$ increases, causing $V_{out}$ to drop. This drops $V_G$, which reduces the Gate-Source voltage ($V_{GS}$), thereby reducing $I_D$ and stabilizing the circuit.\n\n**AC Signal Operation (Amplification):**\n1.  **Input Increase**: If the input voltage $V_{in}$ (at the Source) increases, the Gate-Source voltage $V_{GS} = V_G - V_S$ decreases (assuming $V_G$ doesn't change instantly).\n2.  **Current Change**: A decrease in $V_{GS}$ causes the drain current $I_D$ flowing through the MOSFET to decrease.\n3.  **Output Change**: Since $V_{out} = V_{DD} - I_D R_{effective}$, a decrease in current $I_D$ leads to a smaller voltage drop across $R_D$, causing the output voltage $V_{out}$ to **increase**.\n4.  **Feedback**: The increase in $V_{out}$ is fed back to the Gate through $R_1$, raising $V_G$. This partially counteracts the initial change, confirming negative feedback.\n\nSince an increase in $V_{in}$ leads to an increase in $V_{out}$, the amplifier is **non-inverting**.\n\n### 4. Voltage Gain\nAssuming the open-loop gain of the stage ($g_m R_D$) is large, the closed-loop voltage gain ($A_v$) is determined primarily by the feedback resistors $R_1$ and $R_2$, similar to a non-inverting op-amp:\n\n$$A_v = \\frac{V_{out}}{V_{in}} \\approx 1 + \\frac{R_1}{R_2}$$\n\n**Summary:**\nThe circuit functions as a **non-inverting voltage amplifier**. It takes an input signal at the source, amplifies it, and outputs it at the drain with a gain set by the ratio of resistors $R_1$ and $R_2$. The feedback network stabilizes the gain and the DC bias point.",
        "format": "markdown",
        "sha256": "bc22f02e697042eb62f16d4f34783b92ca5a7f1dca24d1280ba34437286e1c5c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-to-gate divider feedback, negative-feedback action, non-inverting response, and large-loop-gain result of approximately 1 + R1/R2.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 7923,
        "total_tokens": 9264,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6930,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 7923,
        "total_tokens": 9264,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6930,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-012-source-input-resistive-feedback",
      "part": "part1",
      "question_number": 12,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-012-source-input-resistive-feedback/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components, topology, and function.\n\n### 1. Component Identification\n*   **$M_1$**: An N-channel MOSFET (NMOS). The arrow on the source terminal indicates the type (pointing out/away typically denotes NMOS, though the symbol is stylized). The terminal connected to $V_{in}$ is the Source, the terminal connected to the output node is the Drain, and the central terminal is the Gate.\n*   **$R_D$**: A drain resistor connected to the supply voltage $V_{DD}$. It acts as a load resistor converting the drain current into an output voltage.\n*   **$R_1$ and $R_2$**: These resistors form a voltage divider network.\n*   **$V_{DD}$**: The positive DC supply voltage.\n*   **$V_{in}$**: The input voltage signal applied to the Source of the transistor.\n*   **$V_{out}$**: The output voltage taken from the Drain of the transistor.\n\n### 2. Circuit Topology\nThis circuit is a **MOSFET amplifier with negative feedback**. Specifically, it resembles a **Common Gate** configuration modified with feedback, but functionally it operates very similarly to a **Non-Inverting Operational Amplifier**.\n\n*   **Input**: Applied to the Source terminal ($V_{in}$).\n*   **Output**: Taken from the Drain terminal ($V_{out}$).\n*   **Feedback**: There is a feedback path from the output ($V_{out}$) to the Gate of the transistor through the resistor network $R_1$ and $R_2$.\n    *   $R_1$ connects the Output node to the Gate.\n    *   $R_2$ connects the Gate to Ground.\n    *   This sets the Gate voltage $V_G$ as a fraction of the output voltage: $V_G = V_{out} \\cdot \\frac{R_2}{R_1 + R_2}$.\n\n### 3. Circuit Analysis & Operation\nThe circuit uses **negative feedback** to stabilize the gain. Here is the step-by-step operation:\n\n1.  **Initial Change**: Suppose the input voltage $V_{in}$ increases.\n2.  **Gate-Source Voltage ($V_{GS}$)**: Since $V_{GS} = V_G - V_{in}$, an increase in $V_{in}$ causes $V_{GS}$ to decrease (assuming $V_G$ hasn't changed yet).\n3.  **Drain Current ($I_D$)**: For an NMOS transistor, a decrease in $V_{GS}$ leads to a decrease in the drain current $I_D$.\n4.  **Output Voltage ($V_{out}$)**: The output voltage is determined by $V_{out} = V_{DD} - I_D \\cdot R_D$. Since $I_D$ decreases, the voltage drop across $R_D$ decreases, causing **$V_{out}$ to increase**.\n5.  **Feedback**: The increase in $V_{out}$ is fed back to the Gate through the divider $R_1, R_2$, causing $V_G$ to increase.\n6.  **Stabilization**: The increase in $V_G$ increases $V_{GS}$ ($V_{GS} = V_G - V_{in}$), which counteracts the initial decrease. This confirms it is a negative feedback loop.\n\n### 4. Gain Calculation\nBecause of the high gain of the transistor and the negative feedback, the circuit will try to keep the Gate-Source voltage $V_{GS}$ constant (specifically, close to the threshold voltage for operation, or effectively creating a \"virtual short\" concept similar to op-amps where $V_G \\approx V_{in}$ if the open-loop gain is very high).\n\nIf we assume the loop gain is high, then $V_G \\approx V_{in}$.\nUsing the voltage divider equation for the Gate:\n$$V_G = V_{out} \\cdot \\frac{R_2}{R_1 + R_2}$$\n\nSubstituting $V_{in}$ for $V_G$:\n$$V_{in} \\approx V_{out} \\cdot \\frac{R_2}{R_1 + R_2}$$\n\nRearranging for the voltage gain ($A_v = V_{out} / V_{in}$):\n$$A_v = \\frac{V_{out}}{V_{in}} \\approx \\frac{R_1 + R_2}{R_2} = 1 + \\frac{R_1}{R_2}$$\n\n### Conclusion\nThis circuit functions as a **Non-Inverting Amplifier**.\n*   The output signal is in phase with the input signal.\n*   The voltage gain is determined primarily by the ratio of the feedback resistors $R_1$ and $R_2$, approximately equal to **$1 + \\frac{R_1}{R_2}$**.",
        "format": "markdown",
        "sha256": "70344bfbcd650fd6a98b7668d73f9c48554b9c120b4a2204aed4baa1c7e49e46"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source input, output-to-gate divider feedback, and negative-feedback operation. Its high-loop-gain estimate of the non-inverting gain, 1 + R1/R2, is also correct.",
          "golden_solution_sha256": "c4eb57e96a0e70ff6aa718bcfd4e80be89f93bd2bf97d638ee206a2ecd64f575",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 7448,
        "total_tokens": 8789,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6368,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1341,
        "output_tokens": 7448,
        "total_tokens": 8789,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6368,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the circuit:\n\n### 1. Circuit Identification\nThis circuit is an **NMOS Source Follower** (also known as a **Common Drain Amplifier**) with an **active current source load**.\n\n### 2. Component Breakdown\n*   **Transistor $M_1$ (Driver):**\n    *   **Type:** NMOS (indicated by the arrow pointing outwards on the source terminal).\n    *   **Configuration:** Common Drain. The input $V_{in}$ is applied to the Gate, the Drain is connected to the supply voltage $V_{DD}$, and the output $V_{out}$ is taken from the Source.\n*   **Transistor $M_2$ (Load):**\n    *   **Type:** NMOS.\n    *   **Configuration:** It acts as a **constant current source**. Its Gate is connected to a fixed bias voltage $V_b$, its Source is connected to Ground, and its Drain is connected to the output node.\n\n### 3. Circuit Operation\n*   **Biasing:** The transistor $M_2$ is biased by the constant voltage $V_b$. Assuming $M_2$ is in the saturation region ($V_b > V_{th}$ and $V_{out} > V_b - V_{th}$), it will conduct a constant current, let's call it $I_{bias}$.\n*   **Current Flow:** Since $M_1$ and $M_2$ are in series, the same current $I_{bias}$ must flow through $M_1$.\n*   **Voltage Relationship:** For $M_1$ to conduct this constant current $I_{bias}$, its Gate-Source voltage ($V_{GS1}$) must remain roughly constant.\n    *   We know that $V_{GS1} = V_{in} - V_{out}$.\n    *   Therefore, $V_{out} = V_{in} - V_{GS1}$.\n*   **Function:** The output voltage $V_{out}$ \"follows\" the input voltage $V_{in}$, but is shifted down by a DC voltage drop equal to $V_{GS1}$ (which is approximately $V_{th} + V_{overdrive}$).\n\n### 4. Key Characteristics\n*   **Voltage Gain ($A_v$):** The voltage gain is slightly less than unity (1). Ideally, $A_v \\approx 1$. In reality, due to the **body effect** (since the source of $M_1$ is not at ground potential, its threshold voltage changes) and finite output resistance, the gain is given approximately by:\n    $$A_v \\approx \\frac{g_{m1}}{g_{m1} + g_{mb1}}$$\n    where $g_{m1}$ is the transconductance of $M_1$ and $g_{mb1}$ is the body-effect transconductance. Since $g_{mb1}$ is a fraction of $g_{m1}$, the gain is typically around 0.8 to 0.9.\n*   **Input Impedance:** Very high (ideally infinite at low frequencies) because the input is connected to the gate of a MOSFET.\n*   **Output Impedance:** Low. The output impedance is roughly $1/g_{m1}$ (in parallel with the output resistances of the transistors). This makes the circuit an excellent **voltage buffer**, capable of driving low-impedance loads without significant signal loss.\n\n### 5. Summary\nThis circuit is primarily used as a **voltage buffer** to isolate a high-impedance source from a low-impedance load, or as a **level shifter** to shift the DC voltage level down by approximately $V_{GS}$.",
        "format": "markdown",
        "sha256": "6d29816439cccb00cea5c9000070081ff72f96318f213263ba92bbf850d67149"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as its NMOS current-source load, and gives the positive, slightly sub-unity gain with body-effect reasoning. The output-resistance approximation is somewhat simplified, but this does not affect the essential answer.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 4111,
        "total_tokens": 5077,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3287,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 4111,
        "total_tokens": 5077,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3287,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and its functionality.\n\n### 1. Circuit Identification\nThe circuit shown is a **Source Follower** (also known as a **Common Drain Amplifier**) with an **active current source load**.\n\n### 2. Component Analysis\n*   **Transistors ($M_1$ and $M_2$):** Both symbols represent **NMOS** transistors. We can identify this by the arrow on the source terminal pointing outward (away from the channel/gate).\n*   **$M_1$ (Top Transistor):**\n    *   **Gate:** Connected to the input voltage $V_{in}$.\n    *   **Drain:** Connected to the supply voltage $V_{DD}$.\n    *   **Source:** Connected to the output node $V_{out}$.\n    *   **Configuration:** This is a **Common Drain** configuration because the drain is at a fixed AC potential ($V_{DD}$ is an AC ground) and the output is taken from the source.\n*   **$M_2$ (Bottom Transistor):**\n    *   **Gate:** Connected to a constant bias voltage $V_b$.\n    *   **Drain:** Connected to the output node $V_{out}$.\n    *   **Source:** Connected to Ground.\n    *   **Configuration:** Since the gate voltage $V_b$ is constant, $M_2$ acts as a **constant current source** (or active load), assuming it is biased in the saturation region.\n\n### 3. Circuit Operation\n*   **DC Bias:** The transistor $M_2$ is biased by the constant voltage $V_b$. This sets a constant drain current $I_D$ flowing through the branch (from $V_{DD}$ to Ground).\n*   **Signal Path:** The input signal $V_{in}$ is applied to the gate of $M_1$. As $V_{in}$ changes, the current through $M_1$ tries to change. However, since $M_2$ forces a relatively constant current, the voltage at the source ($V_{out}$) must adjust to maintain that current.\n*   **Voltage Relationship:** For an NMOS transistor to conduct, the gate-source voltage ($V_{GS}$) must be greater than the threshold voltage ($V_{th}$). Therefore:\n    $$V_{GS1} = V_{in} - V_{out}$$\n    Rearranging for the output voltage:\n    $$V_{out} = V_{in} - V_{GS1}$$\n    Since the current is roughly constant (set by $M_2$), $V_{GS1}$ is approximately constant. Thus, the output voltage $V_{out}$ \"follows\" the input voltage $V_{in}$, shifted down by a constant DC value ($V_{GS1}$).\n\n### 4. Key Characteristics\n*   **Voltage Gain:** The small-signal voltage gain ($A_v$) is slightly less than unity (1). Ideally, $A_v \\approx 1$. It is a non-inverting amplifier.\n*   **Impedance:**\n    *   **Input Impedance:** Very high (looking into the gate of a MOSFET).\n    *   **Output Impedance:** Low (looking into the source of the transistor, roughly $1/g_m$).\n*   **Function:** This circuit is typically used as a **voltage buffer**. It can drive low-impedance loads without loading down the input signal source. It is also used as a **level shifter** to shift the DC level of a signal down by $V_{GS}$.\n\n### 5. Limitations\n*   **Output Swing:** The output voltage cannot reach the full supply rail $V_{DD}$. The maximum output voltage is approximately $V_{in(max)} - V_{th}$. If $V_{in}$ goes up to $V_{DD}$, the max $V_{out}$ is $V_{DD} - V_{GS}$. This is often referred to as a \"threshold drop.\"",
        "format": "markdown",
        "sha256": "4d321d4074510261b6a95fc5bdc113b7f8601e4c2e9dee5583a8cb7279a38ad0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower with M2 as the NMOS current-source load, and gives a positive, slightly-less-than-unity gain. The omitted body-effect and output-resistance refinements are not essential.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 3940,
        "total_tokens": 4906,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3057,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 3940,
        "total_tokens": 4906,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3057,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-013-source-follower-current-source-load",
      "part": "part1",
      "question_number": 13,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-013-source-follower-current-source-load/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and its function.\n\n### 1. Circuit Identification\nThis circuit is an **NMOS Source Follower** (also known as a **Common Drain Amplifier**) with an **active current source load**.\n\n### 2. Component Breakdown\n*   **Transistor $M_1$ (Driver):**\n    *   **Type:** NMOS transistor (indicated by the arrow pointing outwards on the source terminal).\n    *   **Configuration:** Common Drain. The Drain is connected to the supply voltage ($V_{DD}$), the Gate is the input ($V_{in}$), and the Source is the output ($V_{out}$).\n    *   **Role:** This is the main amplifying transistor. It acts as a buffer, passing the input voltage to the output with a slight drop.\n\n*   **Transistor $M_2$ (Load):**\n    *   **Type:** NMOS transistor.\n    *   **Configuration:** The Gate is connected to a constant bias voltage ($V_b$), the Drain is connected to the output node, and the Source is connected to Ground.\n    *   **Role:** This transistor acts as a **constant current source** (active load). By holding $V_b$ constant (and assuming $V_b > V_{th}$), $M_2$ is biased in the saturation region and draws a constant current from the node $V_{out}$ to ground.\n\n### 3. Circuit Operation\n*   **Biasing:** The voltage $V_b$ sets a constant current $I_{bias}$ flowing through the series combination of $M_1$ and $M_2$.\n    $$I_{D2} \\approx \\frac{1}{2} \\mu_n C_{ox} \\left(\\frac{W}{L}\\right)_2 (V_b - V_{th2})^2$$\n*   **Signal Path:** Since $M_1$ and $M_2$ are in series, the current flowing through $M_1$ must equal the current flowing through $M_2$ ($I_{D1} = I_{D2} = I_{bias}$).\n*   **Input-Output Relationship:** Because the current $I_{D1}$ is constant, the gate-to-source voltage of $M_1$ ($V_{GS1}$) remains roughly constant.\n    $$V_{GS1} = V_{in} - V_{out} \\approx \\text{constant}$$\n    Therefore, the output voltage follows the input voltage:\n    $$V_{out} = V_{in} - V_{GS1}$$\n    Where $V_{GS1} = V_{th1} + V_{overdrive}$.\n\n### 4. Key Characteristics\n*   **Voltage Gain:** The voltage gain is slightly less than unity (1). Ideally, $A_v \\approx 1$. In reality, due to the body effect (since the source of $M_1$ is not at ground potential) and finite output resistance, the gain is typically around 0.8 to 0.9.\n    $$A_v = \\frac{g_{m1}}{g_{m1} + g_{mb1} + g_{ds1} + g_{ds2}}$$\n*   **Input Impedance:** Very high (infinite at low frequencies), as the input is connected to the gate of a MOSFET.\n*   **Output Impedance:** Low. The output impedance is approximately $1/g_{m1}$ (parallel with the output resistances of the transistors). This makes the circuit excellent for driving low-impedance loads.\n*   **Level Shifting:** The circuit shifts the DC level of the input signal down by $V_{GS1}$. This is often used in multi-stage amplifiers to shift voltage levels between stages.\n\n### Summary\nThe circuit acts as a **voltage buffer**. It takes a high-impedance input signal ($V_{in}$) and provides a low-impedance output signal ($V_{out}$) that closely tracks the input, shifted down by a constant voltage drop ($V_{GS}$).",
        "format": "markdown",
        "sha256": "c5d1165e32bce27aa90c50566f217ea00b5e9861451149f79679327c7f5723de"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower and M2 as the NMOS current-source load, and gives a positive gain slightly below unity with a suitable small-signal expression.",
          "golden_solution_sha256": "9c0eaf5035e4eafe98a151f1035fd6512be41f7b78831b9e6cd3dd9618a8eb67",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 3235,
        "total_tokens": 4201,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2335,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 966,
        "output_tokens": 3235,
        "total_tokens": 4201,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2335,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the components and its operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter). It is the fundamental building block of digital logic circuits.\n\n### 2. Component Analysis\n*   **$M_1$ (Bottom Transistor):** This is an **NMOS** (N-channel Metal-Oxide-Semiconductor) transistor. We can identify it by the arrow on the source terminal pointing outward (away from the channel). Its source is connected to Ground.\n*   **$M_2$ (Top Transistor):** This is a **PMOS** (P-channel Metal-Oxide-Semiconductor) transistor. We can identify it by the arrow on the source terminal pointing inward (towards the channel). Its source is connected to the supply voltage, $V_{DD}$.\n\n### 3. Connections\n*   **Input ($V_{in}$):** The gates of both transistors ($M_1$ and $M_2$) are connected together to the input signal $V_{in}$.\n*   **Output ($V_{out}$):** The drains of both transistors are connected together to form the output node $V_{out}$.\n\n### 4. Operation Analysis\nThe circuit operates as a logical NOT gate. Here is how it behaves for different input states:\n\n**Case 1: Input is Low ($V_{in} = 0$ V / Logic 0)**\n*   **NMOS ($M_1$):** The gate-to-source voltage ($V_{GS}$) is 0 V. Since this is below the threshold voltage, $M_1$ is **OFF** (acts as an open switch).\n*   **PMOS ($M_2$):** The source-to-gate voltage ($V_{SG}$) is $V_{DD}$. Since this is greater than the magnitude of the threshold voltage, $M_2$ is **ON** (acts as a closed switch).\n*   **Result:** The output $V_{out}$ is connected to $V_{DD}$ through the conducting PMOS transistor. Therefore, **$V_{out} \\approx V_{DD}$ (Logic 1)**.\n\n**Case 2: Input is High ($V_{in} = V_{DD}$ / Logic 1)**\n*   **NMOS ($M_1$):** The gate-to-source voltage ($V_{GS}$) is $V_{DD}$. Since this is above the threshold voltage, $M_1$ is **ON** (acts as a closed switch).\n*   **PMOS ($M_2$):** The source-to-gate voltage ($V_{SG}$) is 0 V ($V_{DD} - V_{DD}$). Since this is below the threshold magnitude, $M_2$ is **OFF** (acts as an open switch).\n*   **Result:** The output $V_{out}$ is connected to Ground through the conducting NMOS transistor. Therefore, **$V_{out} \\approx 0$ V (Logic 0)**.\n\n### 5. Summary\n*   **Logic Function:** Inverter (NOT gate). If Input is 0, Output is 1. If Input is 1, Output is 0.\n*   **Key Advantage:** In a steady state (when the input is stable at either 0 or 1), one of the transistors is always OFF. This means there is no direct path for current to flow from $V_{DD}$ to Ground, resulting in **very low static power consumption**.",
        "format": "markdown",
        "sha256": "0c3ed9d879c50f2ee86d0643da96dc45c479d195fbc6afb59463c5421986e33f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, its NMOS pull-down and PMOS pull-up, their connections, and the complementary logic operation with no static current at logic levels.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 2616,
        "total_tokens": 2858,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1837,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 2616,
        "total_tokens": 2858,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1837,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis:\n\n**1. Circuit Identification**\nThe circuit shown is a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter). It is the fundamental building block of digital logic circuits.\n\n**2. Components**\n*   **$M_1$ (Bottom Transistor):** This is an **NMOS** transistor. Its source is connected to ground, and its gate is connected to the input $V_{in}$.\n*   **$M_2$ (Top Transistor):** This is a **PMOS** transistor. Its source is connected to the power supply $V_{DD}$, and its gate is connected to the input $V_{in}$.\n\n**3. Circuit Configuration**\n*   The gates of both transistors are tied together to form the input node ($V_{in}$).\n*   The drains of both transistors are tied together to form the output node ($V_{out}$).\n*   This creates a \"push-pull\" configuration where the PMOS acts as a pull-up device and the NMOS acts as a pull-down device.\n\n**4. Operation Analysis**\n\nThe circuit operates based on the input voltage level ($V_{in}$):\n\n*   **Case 1: Input is Low ($V_{in} \\approx 0$ V)**\n    *   **NMOS ($M_1$):** The gate-to-source voltage ($V_{GS}$) is 0 V, which is less than the threshold voltage. Therefore, $M_1$ is **OFF** (open circuit).\n    *   **PMOS ($M_2$):** The source-to-gate voltage ($V_{SG}$) is $V_{DD}$, which is greater than the magnitude of the threshold voltage. Therefore, $M_2$ is **ON** (closed switch).\n    *   **Result:** The output $V_{out}$ is connected to $V_{DD}$. So, **$V_{out} = V_{DD}$ (Logic High / 1)**.\n\n*   **Case 2: Input is High ($V_{in} \\approx V_{DD}$)**\n    *   **NMOS ($M_1$):** The gate-to-source voltage ($V_{GS}$) is $V_{DD}$, which is greater than the threshold voltage. Therefore, $M_1$ is **ON** (closed switch).\n    *   **PMOS ($M_2$):** The source-to-gate voltage ($V_{SG}$) is 0 V. Therefore, $M_2$ is **OFF** (open circuit).\n    *   **Result:** The output $V_{out}$ is connected to Ground. So, **$V_{out} = 0$ V (Logic Low / 0)**.\n\n**5. Summary Truth Table**\n\n| Input ($V_{in}$) | Output ($V_{out}$) | Logic Function |\n| :--- | :--- | :--- |\n| 0 (Low) | $V_{DD}$ (High) | NOT 0 = 1 |\n| 1 (High) | 0 (Low) | NOT 1 = 0 |\n\n**6. Key Characteristics**\n*   **Logic Function:** It performs the logical NOT operation ($Y = \\bar{A}$).\n*   **Low Static Power Consumption:** In either steady state (input is fully high or fully low), one of the transistors is always OFF. This prevents a direct current path from $V_{DD}$ to Ground, meaning almost zero power is consumed when the circuit is not switching.\n*   **Rail-to-Rail Output:** The output voltage swings fully from 0 V to $V_{DD}$.",
        "format": "markdown",
        "sha256": "1404512e7b619767cae1584e3a77f5728ac0df9af3348fbd42e428edab8c2f19"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, its NMOS pull-down and PMOS pull-up, and its inverting operation at both logic levels.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 1898,
        "total_tokens": 2140,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1090,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 1898,
        "total_tokens": 2140,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1090,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-014-cmos-inverter",
      "part": "part1",
      "question_number": 14,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-014-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis:\n\n**1. Circuit Identification**\nThe circuit shown is a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter). It is the fundamental building block of digital logic circuits.\n\n**2. Components**\n*   **$M_1$:** This is an **NMOS** transistor (N-channel MOSFET). You can identify it by the arrow on the source terminal pointing outward. Its source is connected to Ground.\n*   **$M_2$:** This is a **PMOS** transistor (P-channel MOSFET). You can identify it by the arrow on the source terminal pointing inward (and the bubble at the gate, though the bubble is sometimes omitted in simplified symbols, the arrow direction is key). Its source is connected to the power supply $V_{DD}$.\n\n**3. Connections**\n*   **Input ($V_{in}$):** The gates of both transistors ($M_1$ and $M_2$) are connected together to the input voltage $V_{in}$.\n*   **Output ($V_{out}$):** The drains of both transistors are connected together to form the output node $V_{out}$.\n\n**4. Operation Analysis**\nThe circuit works by switching the transistors on and off based on the input voltage.\n\n*   **Case 1: Input is Low ($V_{in} = 0$ V)**\n    *   **$M_1$ (NMOS):** The gate-to-source voltage ($V_{GS}$) is 0 V. Since this is below the threshold voltage, $M_1$ is **OFF** (open circuit).\n    *   **$M_2$ (PMOS):** The source-to-gate voltage ($V_{SG}$) is $V_{DD}$. Since this is greater than the magnitude of the threshold voltage, $M_2$ is **ON** (closed switch).\n    *   **Result:** The output $V_{out}$ is connected to $V_{DD}$ through $M_2$. Therefore, **$V_{out} = V_{DD}$ (Logic High)**.\n\n*   **Case 2: Input is High ($V_{in} = V_{DD}$)**\n    *   **$M_1$ (NMOS):** The gate-to-source voltage ($V_{GS}$) is $V_{DD}$. Since this is above the threshold voltage, $M_1$ is **ON** (closed switch).\n    *   **$M_2$ (PMOS):** The source-to-gate voltage ($V_{SG}$) is 0 V. Since this is below the threshold magnitude, $M_2$ is **OFF** (open circuit).\n    *   **Result:** The output $V_{out}$ is connected to Ground through $M_1$. Therefore, **$V_{out} = 0$ V (Logic Low)**.\n\n**5. Summary**\n*   **Logic Function:** NOT gate (Inverter).\n    *   Input 0 $\\rightarrow$ Output 1\n    *   Input 1 $\\rightarrow$ Output 0\n*   **Key Advantage:** In steady state (when the input is constant at either 0 or $V_{DD}$), one of the transistors is always off. This means there is no direct path from $V_{DD}$ to Ground, resulting in **very low static power consumption**.",
        "format": "markdown",
        "sha256": "0f730fcce63eeac8a6f7d0adb2f2a420ebc29b42340c0170f8647773191d28bf"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the CMOS inverter, its NMOS pull-down and PMOS pull-up, and explains the complementary switching and logic levels. Full credit is warranted.",
          "golden_solution_sha256": "840046eac3d7c03b675f1189f0c155481e30a0dabe801adc9eba216a9a4a04f4",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 1779,
        "total_tokens": 2021,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1034,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 1779,
        "total_tokens": 2021,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1034,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit topology shown in the figure, this is a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter).\n\nAlthough the schematic symbols for both transistors ($M_1$ and $M_2$) are drawn as NMOS transistors (indicated by the arrow pointing outward from the source), the configuration—two transistors in series between power ($V_{DD}$) and ground, with gates tied together and output taken from the middle—is the standard topology for a CMOS inverter. In a correct CMOS schematic, the top transistor ($M_1$) would be a PMOS device.\n\nHere is the analysis assuming the standard CMOS Inverter functionality:\n\n### 1. Circuit Components\n*   **$M_1$ (Top Transistor):** Acts as the **Pull-Up Network (PUN)**. In a CMOS inverter, this is a **PMOS** transistor. Its source is connected to $V_{DD}$ and its drain to the output.\n*   **$M_2$ (Bottom Transistor):** Acts as the **Pull-Down Network (PDN)**. This is an **NMOS** transistor. Its drain is connected to the output and its source to Ground.\n*   **$V_{in}$:** The input voltage applied to the gates of both transistors.\n*   **$V_{out}$:** The output voltage.\n\n### 2. Operation Analysis\nThe circuit functions as a logical NOT gate (Inverter).\n\n*   **Case 1: Input is Low ($V_{in} = 0$ V)**\n    *   **$M_2$ (NMOS):** The gate-source voltage $V_{GS} = 0$. Since this is less than the threshold voltage ($V_{th}$), $M_2$ is **OFF** (open circuit).\n    *   **$M_1$ (PMOS):** The source-gate voltage $V_{SG} = V_{DD} - 0 = V_{DD}$. Since this is greater than the magnitude of the threshold voltage ($|V_{tp}|$), $M_1$ is **ON** (closed circuit).\n    *   **Result:** The output $V_{out}$ is connected to $V_{DD}$.\n    *   **Logic:** Input 0 $\\rightarrow$ Output 1 ($V_{DD}$).\n\n*   **Case 2: Input is High ($V_{in} = V_{DD}$)**\n    *   **$M_2$ (NMOS):** The gate-source voltage $V_{GS} = V_{DD}$. Since $V_{DD} > V_{th}$, $M_2$ is **ON** (closed circuit).\n    *   **$M_1$ (PMOS):** The source-gate voltage $V_{SG} = V_{DD} - V_{DD} = 0$. Since this is less than $|V_{tp}|$, $M_1$ is **OFF** (open circuit).\n    *   **Result:** The output $V_{out}$ is connected to Ground.\n    *   **Logic:** Input 1 $\\rightarrow$ Output 0 (GND).\n\n### 3. Key Characteristics\n*   **Logic Function:** $V_{out} = \\text{NOT}(V_{in})$.\n*   **Power Consumption:** Ideally, there is **zero static power consumption**. In either steady state (High or Low), one of the transistors is always OFF, preventing a direct current path from $V_{DD}$ to Ground. Current only flows briefly during switching.\n*   **Output Swing:** The output swings \"rail-to-rail,\" meaning it goes fully from 0 V to $V_{DD}$.\n\n---\n**Note on Literal Interpretation:**\nIf the diagram is interpreted strictly as drawn (two NMOS transistors):\n*   When $V_{in}$ is Low, both transistors are OFF, leaving $V_{out}$ floating (undefined state).\n*   When $V_{in}$ is High, both transistors turn ON, creating a direct path from $V_{DD}$ to Ground (short circuit), causing high power consumption and an undefined output voltage determined by the ratio of the transistor resistances. This confirms that the diagram is intended to represent a CMOS Inverter.",
        "format": "markdown",
        "sha256": "425c626bc0693439b07bd8d4d0c95d10dce13edb4feedc5132bb7be975cebcf2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer treats the circuit as a conventional complementary CMOS inverter and assigns the upper device a PMOS role. The actual circuit has two NMOS devices, with the upper acting as a source follower and the lower as a pull-down; the stated inverter behavior and literal two-NMOS analysis are incorrect.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 8985,
        "total_tokens": 9227,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 8985,
        "total_tokens": 9227,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit topology shown in the figure, here is an analysis.\n\n### 1. Circuit Identification\nThe circuit shown is the standard topology for a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter). It consists of two MOSFET transistors, $M_1$ and $M_2$, connected in series between the power supply ($V_{DD}$) and ground.\n\n*   **$M_1$ (Top Transistor):** This acts as the **pull-up** network. In a standard CMOS inverter, this is a **PMOS** transistor. (Note: While the schematic symbol shows an arrow pointing outward which typically denotes an NMOS, the position connected to $V_{DD}$ in this complementary configuration implies it functions as the PMOS device).\n*   **$M_2$ (Bottom Transistor):** This acts as the **pull-down** network. This is an **NMOS** transistor.\n\n### 2. Circuit Operation\nThe circuit operates as a digital logic gate (specifically a NOT gate) based on the input voltage $V_{in}$.\n\n**Case A: Input is LOW ($V_{in} \\approx 0$ V)**\n*   **$M_2$ (NMOS):** The gate-to-source voltage $V_{GS} = 0$ V. Since this is less than the threshold voltage ($V_{th}$), the transistor is **OFF** (acts as an open switch).\n*   **$M_1$ (PMOS):** The source-to-gate voltage $V_{SG} = V_{DD} - 0 = V_{DD}$. Since this is greater than the magnitude of the threshold voltage ($|V_{th}|$), the transistor is **ON** (acts as a closed switch).\n*   **Result:** The output $V_{out}$ is connected to $V_{DD}$.\n    *   **$V_{out} = \\text{HIGH}$ (Logic 1)**\n\n**Case B: Input is HIGH ($V_{in} \\approx V_{DD}$)**\n*   **$M_2$ (NMOS):** The gate-to-source voltage $V_{GS} = V_{DD}$. Since this is greater than $V_{th}$, the transistor is **ON**.\n*   **$M_1$ (PMOS):** The source-to-gate voltage $V_{SG} = V_{DD} - V_{DD} = 0$ V. Since this is less than $|V_{th}|$, the transistor is **OFF**.\n*   **Result:** The output $V_{out}$ is connected to Ground.\n    *   **$V_{out} = \\text{LOW}$ (Logic 0)**\n\n### 3. Summary of Function\n*   **Logic Function:** Inverter (NOT Gate).\n    *   If Input is 0, Output is 1.\n    *   If Input is 1, Output is 0.\n    *   Equation: $V_{out} = \\overline{V_{in}}$\n\n### 4. Key Characteristics\n*   **High Input Impedance:** The gates of the MOSFETs are insulated, meaning the circuit draws almost zero current from the input source ($V_{in}$).\n*   **Low Static Power Consumption:** In either steady state (High or Low), one of the transistors is always OFF. This prevents a direct current path from $V_{DD}$ to Ground, minimizing power usage.\n*   **Rail-to-Rail Output:** The output voltage swings fully from 0 V to $V_{DD}$.\n\n---\n**Note on Schematic Symbols:**\nStrictly speaking, the arrow symbols on both transistors point outward, which is the standard symbol for **NMOS** transistors. If interpreted literally as two NMOS transistors:\n*   $M_1$ would be a \"source follower\" (Drain at $V_{DD}$, Source at $V_{out}$).\n*   $M_2$ would be a \"common source\" switch (Drain at $V_{out}$, Source at GND).\n*   In this specific \"all-NMOS\" configuration, when $V_{in}$ is High, both turn on. $M_2$ pulls the output down strongly, while $M_1$ tries to pull it up weakly (limited to $V_{in} - V_{th}$). The output would go Low. When $V_{in}$ is Low, both are off, and the output would be floating (High-Z). This is less common than the CMOS interpretation above.",
        "format": "markdown",
        "sha256": "a9978cc6778c87f4f65d05a459950b0169a0ad11955382934d8c475fc75dc0d8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The main analysis misidentifies the upper NMOS as a PMOS and treats the circuit as an ordinary CMOS inverter, which the scoring gate explicitly assigns 0. The later all-NMOS note does not resolve that contradiction.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 13875,
        "total_tokens": 14117,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12873,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 13875,
        "total_tokens": 14117,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12873,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-015-malformed-cmos-inverter",
      "part": "part1",
      "question_number": 15,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-015-malformed-cmos-inverter/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit topology and standard electronic symbols, here is an analysis of the circuit.\n\n### 1. Circuit Identification\nThe circuit shown is a **CMOS Inverter** (Complementary Metal-Oxide-Semiconductor Inverter). It is the fundamental building block of digital logic circuits.\n\nAlthough the schematic symbols for both transistors ($M_1$ and $M_2$) show arrows pointing outward (which typically denotes NMOS transistors), the topology—where the top transistor is connected to the positive supply ($V_{DD}$) and the bottom transistor to ground, with their gates tied together—is the standard configuration for a complementary pair. In this context:\n*   **$M_1$** functions as a **PMOS** transistor (Pull-up network).\n*   **$M_2$** functions as an **NMOS** transistor (Pull-down network).\n\n### 2. Component Analysis\n*   **$M_1$ (Top Transistor):** This is the load transistor. In a CMOS inverter, this is a PMOS device. Its source is connected to $V_{DD}$ and its drain is connected to the output $V_{out}$.\n*   **$M_2$ (Bottom Transistor):** This is the driver transistor. It is an NMOS device. Its drain is connected to the output $V_{out}$ and its source is connected to Ground.\n*   **Input ($V_{in}$):** Connected to the gates of both transistors.\n*   **Output ($V_{out}$):** Taken from the common node between the drain of $M_1$ and the drain of $M_2$.\n\n### 3. Circuit Operation\nThe circuit operates as a logical NOT gate (Inverter).\n\n*   **Case 1: Input is Low ($V_{in} \\approx 0$ V)**\n    *   **$M_2$ (NMOS):** The gate-source voltage $V_{GS} = 0$ V. Since this is less than the threshold voltage ($V_{th}$), $M_2$ is **OFF** (acts as an open switch).\n    *   **$M_1$ (PMOS):** The source-gate voltage $V_{SG} = V_{DD} - 0 = V_{DD}$. Since this is greater than the magnitude of the threshold voltage ($|V_{tp}|$), $M_1$ is **ON** (acts as a closed switch).\n    *   **Result:** The output $V_{out}$ is connected to $V_{DD}$.\n    *   **$V_{out} = V_{DD}$ (Logic High)**.\n\n*   **Case 2: Input is High ($V_{in} \\approx V_{DD}$)**\n    *   **$M_2$ (NMOS):** The gate-source voltage $V_{GS} = V_{DD}$. Since $V_{GS} > V_{th}$, $M_2$ is **ON** (acts as a closed switch).\n    *   **$M_1$ (PMOS):** The source-gate voltage $V_{SG} = V_{DD} - V_{DD} = 0$ V. Since this is less than $|V_{tp}|$, $M_1$ is **OFF** (acts as an open switch).\n    *   **Result:** The output $V_{out}$ is connected to Ground.\n    *   **$V_{out} = 0$ V (Logic Low)**.\n\n### 4. Summary of Characteristics\n*   **Logic Function:** $V_{out} = \\text{NOT } V_{in}$ (Inverter).\n*   **Input Impedance:** Very high (since the gates of MOSFETs are insulated, drawing almost zero DC current).\n*   **Output Impedance:** Low (in either state, one transistor is fully on, providing a strong drive to the output).\n*   **Power Consumption:** Ideally zero static power dissipation. In steady state (either High or Low), one of the transistors is always OFF, preventing a direct current path from $V_{DD}$ to Ground.\n\n*(Note: If strictly interpreted as two NMOS transistors due to the arrow symbols, the circuit would suffer from \"shoot-through\" current when $V_{in}$ is high, as both transistors would turn on simultaneously, creating a path from $V_{DD}$ to Ground and resulting in poor logic levels. However, the topology strongly indicates a standard CMOS inverter.)*",
        "format": "markdown",
        "sha256": "89cd2a624f7391cc902d3516335f715cc7b5df9941522a554bf0f5456c01584b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the upper transistor as PMOS and analyzes the circuit as an ordinary CMOS inverter. The golden solution makes correct identification of both devices as NMOS non-negotiable.",
          "golden_solution_sha256": "b598ce9b14c47387d9b8d874c626add0f845d3b4bc6f5ad44a431e7ddf11ad3d",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 17913,
        "total_tokens": 18155,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16935,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 242,
        "output_tokens": 17913,
        "total_tokens": 18155,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16935,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the components and the circuit's function.\n\n### 1. Component Identification\n*   **$M_1$ (Bottom Transistor):** This is an **NMOS transistor**. We can identify it by the arrow on the source terminal pointing outward (away from the channel).\n    *   **Source:** Connected to Ground.\n    *   **Gate:** Connected to the input voltage, $V_{in}$.\n    *   **Drain:** Connected to the output node, $V_{out}$.\n*   **$M_2$ (Top Transistor):** This is a **PMOS transistor**. We can identify it by the arrow on the source terminal pointing inward (towards the channel).\n    *   **Source:** Connected to the supply voltage, $V_{DD}$.\n    *   **Gate:** Connected to the Drain (the node between $M_1$ and $M_2$).\n    *   **Drain:** Connected to the output node, $V_{out}$.\n\n### 2. Circuit Configuration\nThis circuit is a **Common-Source Amplifier with a Diode-Connected Load**. It can also be viewed as a type of logic inverter.\n\n*   **Driver Stage:** $M_1$ acts as the driver or input device in a common-source configuration.\n*   **Active Load:** $M_2$ acts as the load. Because its gate is connected directly to its drain, it is **\"diode-connected.\"**\n\n### 3. Circuit Analysis & Operation\n\nThis circuit can be analyzed from two perspectives: Digital (Logic) and Analog (Amplifier).\n\n#### A. Digital Logic Perspective (Inverter)\nThe circuit functions as an inverter (NOT gate), but it is a \"ratioed\" logic family, meaning the output voltage levels depend on the relative sizes of the transistors.\n\n*   **When $V_{in}$ is Low (Logic 0):**\n    *   $M_1$ is OFF (cutoff) because $V_{GS} < V_{th}$.\n    *   $M_2$ turns ON and pulls the output voltage $V_{out}$ up.\n    *   However, because $M_2$ is diode-connected, it will stop conducting when the source-gate voltage $V_{SG}$ drops to its threshold voltage $|V_{tp}|$.\n    *   Therefore, the maximum output voltage is **$V_{out(max)} = V_{DD} - |V_{tp}|$**. This is a \"degraded\" high logic level (it doesn't reach the full $V_{DD}$).\n\n*   **When $V_{in}$ is High (Logic 1):**\n    *   $M_1$ turns ON strongly.\n    *   Current flows from $V_{DD}$ through $M_2$ and $M_1$ to ground.\n    *   $M_1$ pulls $V_{out}$ down towards ground. The final low voltage level ($V_{OL}$) is determined by the ratio of the \"strength\" (transconductance parameter $k$ or $\\beta$) of $M_1$ versus $M_2$. For a good logic low, $M_1$ must be much larger/stronger than $M_2$.\n\n#### B. Analog Perspective (Amplifier)\nIn analog circuit design, this configuration is commonly used as a gain stage.\n\n*   **Small-Signal Model:** The diode-connected PMOS ($M_2$) acts as a small-signal resistor with a resistance of approximately $1/g_{m2}$ (where $g_{m2}$ is the transconductance of $M_2$).\n*   **Voltage Gain:** The circuit amplifies the input signal $V_{in}$. The small-signal voltage gain ($A_v$) is given by:\n    $$A_v \\approx -\\frac{g_{m1}}{g_{m2}}$$\n    *(The negative sign indicates a 180-degree phase shift, i.e., inversion).*\n*   Substituting the formula for transconductance ($g_m \\propto \\sqrt{W/L}$), the gain is roughly proportional to the square root of the ratio of the transistor sizes:\n    $$A_v \\approx -\\sqrt{\\frac{\\mu_n (W/L)_1}{\\mu_p (W/L)_2}}$$\n\n### Summary\nThe figure shows an **NMOS inverter/amplifier with a diode-connected PMOS load**.\n*   **Function:** It inverts the input signal ($V_{in}$).\n*   **Key Characteristic:** The output high level is limited to $V_{DD} - |V_{threshold}|$ due to the diode connection of the load transistor $M_2$.\n*   **Usage:** It is often used in analog integrated circuits as a compact amplifier stage or in specific digital logic families where full CMOS (complementary) logic is not used.",
        "format": "markdown",
        "sha256": "5ce5902e4026156bcaebc7424e8d6725b05ec023fd7def4774a66448e643633a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the inverting gain −gm1/gm2, including the square-law form. The large-signal high-level remark is optional and not penalized by the golden solution.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 4139,
        "total_tokens": 4720,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3059,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 4139,
        "total_tokens": 4720,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3059,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification\nThe circuit consists of two MOSFET transistors:\n*   **$M_1$ (Bottom):** An **NMOS** transistor (indicated by the arrow pointing outwards on the source). It acts as the driver or input stage. Its source is connected to ground, and its gate receives the input voltage $V_{in}$.\n*   **$M_2$ (Top):** A **PMOS** transistor (indicated by the arrow pointing inwards on the source). It acts as the active load. Its source is connected to the supply voltage $V_{DD}$. Crucially, its gate is connected to its drain. This configuration is known as a **diode-connected transistor**.\n\nThe output voltage $V_{out}$ is taken from the common drain node connecting the two transistors.\n\n### 2. Circuit Topology\nThis circuit is a **Common-Source Amplifier with a Diode-Connected Active Load**. It can also function as a logic inverter (specifically, a saturated-load inverter), though with some limitations compared to a standard CMOS inverter.\n\n### 3. Analysis of Transistor Operating Regions\n\n**For Transistor $M_2$ (PMOS Load):**\n*   The gate is connected to the drain, so $V_{G2} = V_{D2} = V_{out}$.\n*   The source is at $V_{DD}$.\n*   Therefore, the source-gate voltage is $V_{SG2} = V_{DD} - V_{out}$ and the source-drain voltage is $V_{SD2} = V_{DD} - V_{out}$.\n*   For a PMOS to be in saturation, the condition is $V_{SD} \\ge V_{SG} - |V_{tp}|$.\n*   Substituting the values: $(V_{DD} - V_{out}) \\ge (V_{DD} - V_{out}) - |V_{tp}|$, which simplifies to $0 \\ge -|V_{tp}|$. This is always true.\n*   **Conclusion:** As long as $M_2$ is turned on ($V_{SG} > |V_{tp}|$), it is **always in the saturation region**.\n\n**For Transistor $M_1$ (NMOS Driver):**\n*   **Cutoff:** If $V_{in} < V_{tn}$ (threshold voltage), $M_1$ is off.\n*   **Saturation:** If $V_{in} > V_{tn}$ and $V_{out} \\ge V_{in} - V_{tn}$.\n*   **Triode (Linear):** If $V_{in} > V_{tn}$ and $V_{out} < V_{in} - V_{tn}$.\n\n### 4. Small-Signal Analysis (Amplifier Application)\nIf this circuit is biased such that both transistors are conducting (acting as an amplifier):\n\n*   **Load Impedance:** A diode-connected transistor acts like a small-signal resistor. Looking into the drain of $M_2$, the equivalent resistance is approximately $1/g_{m2}$ (where $g_{m2}$ is the transconductance of $M_2$).\n*   **Voltage Gain ($A_v$):** The circuit is a common-source amplifier with a load resistance of roughly $1/g_{m2}$.\n    $$A_v = \\frac{v_{out}}{v_{in}} \\approx -g_{m1} \\times \\left( \\frac{1}{g_{m2}} \\right) = -\\frac{g_{m1}}{g_{m2}}$$\n*   **Gain Characteristic:** Since $g_m = \\sqrt{2\\mu C_{ox} (W/L) I_D}$, and both transistors share the same drain current $I_D$, the gain simplifies to:\n    $$A_v \\approx -\\sqrt{\\frac{\\mu_n (W/L)_1}{\\mu_p (W/L)_2}}$$\n    This means the gain is determined by the physical dimensions (aspect ratios) of the transistors and is relatively independent of the bias current.\n\n### 5. Large-Signal Analysis (Logic Inverter Application)\nIf used as a digital logic gate:\n\n*   **Input Low ($V_{in} = 0$ V):** $M_1$ is OFF. No current flows through the branch. $M_2$ will pull $V_{out}$ up until it turns off. $M_2$ turns off when $V_{SG} = |V_{tp}|$.\n    *   $V_{DD} - V_{out} = |V_{tp}| \\Rightarrow V_{out} = V_{DD} - |V_{tp}|$.\n    *   The output is a \"High\" logic level, but it is degraded by the threshold voltage of the PMOS. It does not reach the full $V_{DD}$.\n\n*   **Input High ($V_{in} = V_{DD}$):** $M_1$ is ON (strongly). $M_2$ is also ON. $M_1$ pulls $V_{out}$ down towards ground. The final low voltage level depends on the ratio of the sizes of $M_1$ and $M_2$. For a good logic '0', $M_1$ must be made much larger (wider) than $M_2$.\n\n### Summary\nThe figure shows an **NMOS common-source stage with a diode-connected PMOS load**.\n*   **Key Feature:** The load transistor ($M_2$) is always in saturation.\n*   **Primary Use:** It is commonly used as a basic amplifier stage in integrated circuits where the gain is set by the ratio of transistor sizes ($\\sqrt{(W/L)_1 / (W/L)_2}$).",
        "format": "markdown",
        "sha256": "25bf0718fa5ea6a890a1627ed717e6e2e0c5915dcbb9c9065f8a5ce397f1a471"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-source NMOS stage with a diode-connected PMOS load and gives the accepted inverting gain, including the square-law sizing relation. The large-signal threshold-level simplification is explicitly permitted by the golden solution.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 5296,
        "total_tokens": 5877,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4006,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 5296,
        "total_tokens": 5877,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4006,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-016-common-source-diode-connected-load",
      "part": "part1",
      "question_number": 16,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-016-common-source-diode-connected-load/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the components and its function:\n\n### 1. Component Identification\n*   **$M_1$ (Bottom Transistor):** This is an **NMOS transistor**. We can identify it by the arrow on the source terminal pointing outwards (away from the channel). Its source is connected to ground, and its gate is connected to the input voltage $V_{in}$.\n*   **$M_2$ (Top Transistor):** This is a **PMOS transistor**. We can identify it by the arrow on the source terminal pointing inwards (towards the channel). Its source is connected to the supply voltage $V_{DD}$.\n\n### 2. Circuit Configuration\n*   **Driver Stage ($M_1$):** The NMOS transistor $M_1$ acts as the driver. It is controlled by the input signal $V_{in}$.\n*   **Active Load ($M_2$):** The PMOS transistor $M_2$ acts as the load. Crucially, its **gate is connected to its drain** (the node labeled $V_{out}$). This configuration is known as a **diode-connected transistor**.\n\n### 3. Circuit Function: Inverter (NOT Gate)\nThis circuit functions as a logic inverter, but with specific characteristics due to the diode-connected load. It is often referred to as an **active-load inverter** or a **diode-connected load inverter**.\n\n**Operation Analysis:**\n\n*   **When Input $V_{in}$ is Low (Logic 0):**\n    *   $M_1$ (NMOS) is turned **OFF** (cutoff region) because $V_{GS} < V_{th}$.\n    *   Current cannot flow to ground.\n    *   $M_2$ (PMOS) acts to pull the output voltage $V_{out}$ up towards $V_{DD}$.\n    *   However, because $M_2$ is diode-connected ($V_{SG} = V_{SD}$), it will turn off when the source-gate voltage drops below its threshold voltage ($|V_{tp}|$).\n    *   Therefore, the output high voltage ($V_{OH}$) will not reach the full $V_{DD}$. It will stop at **$V_{DD} - |V_{tp}|$**.\n\n*   **When Input $V_{in}$ is High (Logic 1, e.g., $V_{DD}$):**\n    *   $M_1$ (NMOS) is turned **ON**. It creates a low-resistance path to ground, trying to pull $V_{out}$ down to 0V.\n    *   $M_2$ (PMOS) is also ON because $V_{out}$ is low, making $V_{SG}$ large ($V_{DD} - V_{out} \\approx V_{DD}$).\n    *   Current flows from $V_{DD}$ through $M_2$ and $M_1$ to ground.\n    *   The final output voltage ($V_{OL}$) will be a low value close to 0V, but not exactly 0V. The exact voltage is determined by the ratio of the sizes (Width/Length) of the two transistors. This is a form of **ratioed logic**.\n\n### Summary\nThis is a **CMOS inverter variant with a diode-connected PMOS load**.\n*   **Logic Function:** NOT gate (Inverter).\n*   **Key Characteristic:** Unlike a standard CMOS inverter (where the PMOS gate is connected to $V_{in}$), this circuit cannot pull the output all the way to $V_{DD}$ due to the threshold voltage drop across the diode-connected $M_2$.",
        "format": "markdown",
        "sha256": "bbaa17a792023dc7148bf83f8523162b3dd67496ba4ae876ef74d19f01672897"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the NMOS common-source stage and diode-connected PMOS load, but omits the key small-signal inverting gain, such as −gm1/gm2. The output-level discussion is secondary and does not replace that analysis.",
          "golden_solution_sha256": "890a218dd592ccc44d29c47d073a2630294c84b195016d665cdb5f09108c1fc5",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 3736,
        "total_tokens": 4317,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 581,
        "output_tokens": 3736,
        "total_tokens": 4317,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2922,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the components and the circuit's function.\n\n### 1. Component Identification\n*   **Transistors:** The circuit contains two MOSFETs labeled $M_1$ and $M_2$.\n*   **Type:** The schematic symbol shows the arrow on the source terminal pointing **inward** towards the channel. In standard electronic symbols, an inward-pointing arrow on the source indicates a **PMOS** transistor. (Conversely, an outward-pointing arrow would indicate an NMOS transistor).\n    *   Therefore, both $M_1$ and $M_2$ are **PMOS transistors**.\n\n### 2. Circuit Configuration\n*   **Transistor $M_2$ (Driver):**\n    *   **Source:** Connected to the supply voltage $V_{DD}$.\n    *   **Gate:** Connected to the input voltage $V_{in}$.\n    *   **Drain:** Connected to the output node $V_{out}$.\n    *   This configuration acts as a switch or driver controlled by the input. Since the source is at a fixed high potential ($V_{DD}$), this is effectively a common-source configuration for a PMOS device.\n\n*   **Transistor $M_1$ (Load):**\n    *   **Source:** The terminal with the arrow is the source. In this orientation, the top terminal (connected to $V_{out}$) is the source because it is at a higher potential than the bottom terminal.\n    *   **Gate:** Connected to Ground ($0\\text{ V}$).\n    *   **Drain:** The bottom terminal is connected to Ground.\n    *   Since the Gate and the Drain (bottom terminal) are both connected to Ground, $M_1$ is a **diode-connected PMOS transistor**. It acts as an active load (a non-linear resistor) pulling the output towards ground.\n\n### 3. Circuit Operation\nThis circuit functions as a **Logic Inverter (NOT gate)**, specifically a type of ratioed logic or active-load inverter using PMOS technology.\n\n*   **Case 1: Input is Low ($V_{in} \\approx 0\\text{ V}$)**\n    *   For $M_2$: The source-gate voltage $V_{SG} = V_{DD} - 0 = V_{DD}$. Since $V_{DD} > |V_{th}|$ (threshold voltage), $M_2$ turns **ON**. It conducts current from $V_{DD}$ to $V_{out}$, pulling the output voltage high.\n    *   For $M_1$: As $V_{out}$ rises, the source-gate voltage $V_{SG} = V_{out} - 0 = V_{out}$ increases. Once $V_{out} > |V_{th}|$, $M_1$ turns **ON** and conducts current to ground.\n    *   **Result:** The output $V_{out}$ settles at a high logic level (Logic 1). The exact voltage is determined by the balance of currents between $M_2$ and $M_1$ (ratioed logic), but it will be close to $V_{DD}$.\n\n*   **Case 2: Input is High ($V_{in} \\approx V_{DD}$)**\n    *   For $M_2$: The source-gate voltage $V_{SG} = V_{DD} - V_{DD} = 0$. Since $0 < |V_{th}|$, $M_2$ turns **OFF**. It stops conducting current from the supply.\n    *   For $M_1$: Assuming $V_{out}$ was previously high, $M_1$ is ON ($V_{SG} = V_{out} > |V_{th}|$). It discharges the output node $V_{out}$ to ground.\n    *   As $V_{out}$ drops below $|V_{th}|$, $M_1$ turns **OFF**.\n    *   **Result:** The output $V_{out}$ settles at a low logic level (Logic 0, approx $0\\text{ V}$).\n\n### Summary\nThe circuit is a **PMOS Inverter** with an active load.\n*   **Input:** $V_{in}$\n*   **Output:** $V_{out}$\n*   **Function:** $V_{out} = \\text{NOT}(V_{in})$ (Logic Inversion). When $V_{in}$ is Low, $V_{out}$ is High. When $V_{in}$ is High, $V_{out}$ is Low.",
        "format": "markdown",
        "sha256": "1f85dcc3b085ec520dd9ccb56321a46b1a169cccae3a013ade52ed3aea21735f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies both PMOS devices, M2 as the common-source input device, and M1 as a diode-connected PMOS load. However, it misses the gm/gm gain and incorrectly claims M1 can pull the output to 0 V, treating the circuit as a conventional logic inverter rather than recognizing the limited pull-down.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 14954,
        "total_tokens": 16328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13950,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 14954,
        "total_tokens": 16328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13950,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components and the circuit's function.\n\n### 1. Component Identification\nThe circuit consists of two MOSFET transistors, labeled **$M_1$** and **$M_2$**.\n*   **Symbols:** The transistors are depicted with a vertical bar (channel), a gate terminal, and an arrow on the channel/terminal pointing inwards. In standard schematic symbols where the arrow is on the source terminal, an arrow pointing **inward** indicates a **PMOS** (P-channel) transistor.\n*   **Terminals:**\n    *   **$M_2$ (Top Transistor):** The top terminal is connected to $V_{DD}$ (Source), the gate to $V_{in}$, and the bottom terminal to $V_{out}$ (Drain).\n    *   **$M_1$ (Bottom Transistor):** The top terminal is connected to $V_{out}$ (Source, assuming $V_{out} > 0$), the gate to Ground, and the bottom terminal to Ground (Drain).\n\n### 2. Circuit Configuration\n*   **Driver Transistor ($M_2$):** This is a PMOS transistor configured as a switch or common-source amplifier. Its source is at the supply voltage $V_{DD}$, and it is controlled by the input voltage $V_{in}$.\n*   **Load Transistor ($M_1$):** This is also a PMOS transistor. Notice that its **Gate** and **Drain** (bottom terminal) are both connected to Ground. This configuration is known as a **diode-connected transistor**. It acts as an active load (a non-linear resistor) that pulls the output node towards ground when conducting.\n\n### 3. Circuit Operation\nThe circuit functions as a logic gate, specifically an **Inverter (NOT gate)**, although with specific voltage levels due to the diode-connected load.\n\n*   **Case 1: Input is Low ($V_{in} \\approx 0$ V)**\n    *   For $M_2$ (PMOS): $V_{SG} = V_{DD} - 0 = V_{DD}$. Since $V_{SG} > |V_{th}|$, **$M_2$ turns ON**. It creates a low-resistance path from $V_{DD}$ to $V_{out}$, pulling the output voltage high.\n    *   For $M_1$ (PMOS): As $V_{out}$ rises, $V_{SG}$ for $M_1$ increases ($V_{SG} = V_{out} - 0$). $M_1$ will turn on and conduct current to ground, but since $M_2$ is strongly pulling up, $V_{out}$ will settle at a high voltage (close to $V_{DD}$, minus some drop due to the current balance).\n    *   **Result:** $V_{out}$ is **High**.\n\n*   **Case 2: Input is High ($V_{in} \\approx V_{DD}$)**\n    *   For $M_2$ (PMOS): $V_{SG} = V_{DD} - V_{DD} = 0$. Since $V_{SG} < |V_{th}|$, **$M_2$ turns OFF**. It disconnects $V_{out}$ from $V_{DD}$.\n    *   For $M_1$ (PMOS): Assuming $V_{out}$ was previously high, $V_{SG} = V_{out} > |V_{th}|$, so **$M_1$ is ON**. It pulls charge from the output node to ground, discharging $V_{out}$.\n    *   The voltage $V_{out}$ will drop until $M_1$ turns off (when $V_{out} \\approx |V_{th}|$).\n    *   **Result:** $V_{out}$ is **Low** (approximately $|V_{th}|$).\n\n### Conclusion\nThe circuit acts as a **Logic Inverter (NOT gate)**.\n*   When $V_{in}$ is Low, $V_{out}$ is High.\n*   When $V_{in}$ is High, $V_{out}$ is Low.\n\n*Note: This specific topology (PMOS driver with a diode-connected PMOS load) is a form of \"ratioed logic\" or an active-load amplifier stage. The low output voltage will not be exactly 0V but will be around the threshold voltage $|V_{th}|$ of the transistor $M_1$.*",
        "format": "markdown",
        "sha256": "574ea656b3c522807607517b35cb46c9008ae4f944f287b2fba346dc6c8dd9df"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies both PMOS devices, M2 as the common-source input device, and M1 as a diode-connected PMOS load, with sensible DC inversion behavior. It does not establish the key small-signal gm/gm gain or an equivalent current-balance explanation of that gain, so it falls short of full credit.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 20746,
        "total_tokens": 22120,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19753,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 20746,
        "total_tokens": 22120,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19753,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-017-pmos-input-invalid-pulldown",
      "part": "part1",
      "question_number": 17,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-017-pmos-input-invalid-pulldown/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis:\n\n### 1. Component Identification\nThe circuit consists of two MOSFET transistors, labeled **$M_1$** and **$M_2$**.\n*   **Symbol Analysis:** The arrow on the transistor symbol points inward towards the channel. In standard schematic symbols, an arrow pointing inward on the source terminal indicates a **PMOS transistor**. (Conversely, an outward arrow would indicate an NMOS).\n*   Therefore, both $M_1$ and $M_2$ are **PMOS transistors**.\n\n### 2. Circuit Configuration\n*   **Transistor $M_2$ (Top):**\n    *   **Source:** Connected to $V_{DD}$ (the highest potential, which is the source for a PMOS).\n    *   **Gate:** Connected to the input voltage $V_{in}$.\n    *   **Drain:** Connected to the output node $V_{out}$.\n    *   **Role:** This acts as the **driver transistor** or a switch controlled by the input.\n\n*   **Transistor $M_1$ (Bottom):**\n    *   **Source:** The terminal with the arrow is the source. Here, it is the top terminal connected to $V_{out}$.\n    *   **Gate:** Connected to Ground.\n    *   **Drain:** The bottom terminal is connected to Ground.\n    *   **Role:** Since the Gate and the Drain are both connected to Ground (the same potential), $M_1$ is a **diode-connected PMOS transistor**. It acts as an **active load** (specifically, a nonlinear resistor or current sink).\n\n### 3. Circuit Function: PMOS Inverter (Ratioed Logic)\nThis circuit configuration is a type of logic inverter, specifically using PMOS technology with a saturated/diode-connected load.\n\n**Operation Analysis:**\n\n*   **Case 1: Input is Low ($V_{in} \\approx 0\\text{ V}$)**\n    *   For $M_2$: The source-gate voltage $V_{SG} = V_{DD} - 0 = V_{DD}$. Assuming $V_{DD} > |V_{th}|$ (threshold voltage), **$M_2$ turns ON**. It tries to pull $V_{out}$ up to $V_{DD}$.\n    *   For $M_1$: As $V_{out}$ rises, the source-gate voltage $V_{SG} = V_{out} - 0 = V_{out}$. Once $V_{out} > |V_{th}|$, **$M_1$ turns ON** and starts conducting current to ground.\n    *   **Result:** There is a \"fight\" between the pull-up transistor ($M_2$) and the pull-down load ($M_1$). The output voltage $V_{out}$ will settle at a high logic level (Logic '1'). The exact voltage depends on the ratio of the sizes (Width/Length) of the two transistors. Typically, $M_2$ is made much larger than $M_1$ so that $V_{out}$ is close to $V_{DD}$. Note that in this state, there is a static current flowing from $V_{DD}$ to Ground, which consumes power.\n\n*   **Case 2: Input is High ($V_{in} \\approx V_{DD}$)**\n    *   For $M_2$: The source-gate voltage $V_{SG} = V_{DD} - V_{DD} = 0$. Since $V_{SG} < |V_{th}|$, **$M_2$ turns OFF**. It acts as an open switch.\n    *   For $M_1$: If $V_{out}$ was previously high, $V_{SG} = V_{out} > |V_{th}|$, so **$M_1$ is ON**. It discharges the output node $V_{out}$ to Ground.\n    *   **Result:** $V_{out}$ drops towards $0\\text{ V}$. Once $V_{out}$ drops below $|V_{th}|$, $M_1$ turns off. The output is at a low logic level (Logic '0').\n\n### Summary\nThe circuit functions as a **NOT gate (Inverter)**.\n*   **$V_{in} = \\text{Low} \\rightarrow V_{out} = \\text{High}$**\n*   **$V_{in} = \\text{High} \\rightarrow V_{out} = \\text{Low}$**\n\nIt is a **ratioed logic circuit** because the \"High\" output level is determined by the relative conductance of $M_1$ and $M_2$, rather than being a full rail-to-rail swing like in a standard CMOS inverter.",
        "format": "markdown",
        "sha256": "b15c5f5c95ea949b772666ca58826ce6ffee557d65c316fb586ccc1f7816d6a0"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly identifies both PMOS devices, M2’s input-controlled common-source connections, and M1 as a diode-connected PMOS load; its current-contention explanation also gives the inverse trend. However, it omits the gm/gm gain explanation and overstates M1’s ability to pull Vout to ground, so the inverter analysis is incomplete.",
          "golden_solution_sha256": "b9bd40d93897263d8f8ec48e8a570180ddbbc0962f905b31861c1d4b96315bc9",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 17636,
        "total_tokens": 19010,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16581,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1374,
        "output_tokens": 17636,
        "total_tokens": 19010,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16581,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the step-by-step derivation to find the output resistance $R_{out}$.\n\n**1. Circuit Analysis**\n*   The circuit consists of two PMOS transistors, $M_1$ and $M_2$, connected in series (stacked).\n*   The source of $M_2$ is connected to $V_{DD}$ (AC ground).\n*   The gate of $M_2$ is connected to a constant bias voltage $V_{b2}$ (AC ground).\n*   The drain of $M_2$ is connected to the source of $M_1$ at node $X$.\n*   The gate of $M_1$ is connected to a constant bias voltage $V_{b1}$ (AC ground).\n*   We are looking for the resistance $R_{out}$ looking into the drain of $M_1$.\n\n**2. Small-Signal Model**\nTo find the output resistance, we analyze the small-signal equivalent circuit.\n*   **For $M_2$:** Since its source ($V_{DD}$) and gate ($V_{b2}$) are connected to AC ground, the transistor $M_2$ acts simply as a resistor $r_{o2}$ (its output resistance) connected from node $X$ to ground. The dependent current source $g_{m2}v_{sg2}$ is zero because $v_{sg2} = 0$.\n*   **For $M_1$:** The source of $M_1$ is connected to node $X$. Therefore, the source of $M_1$ sees a resistance $R_S = r_{o2}$ to ground. We are looking into the drain of $M_1$.\n\n**3. Calculation**\nThis configuration is equivalent to a transistor ($M_1$) with source degeneration resistance $R_S = r_{o2}$. The formula for the output resistance looking into the drain of a MOSFET with a source resistance $R_S$ is:\n\n$$R_{out} = r_{o1} + R_S + (g_{m1} + g_{mb1})r_{o1}R_S$$\n\nSubstituting $R_S = r_{o2}$:\n\n$$R_{out} = r_{o1} + r_{o2} + (g_{m1} + g_{mb1})r_{o1}r_{o2}$$\n\nWhere:\n*   $g_{m1}$ is the transconductance of $M_1$.\n*   $g_{mb1}$ is the body-effect transconductance of $M_1$ (often neglected if the body is connected to the source, but for a PMOS in an n-well process, the body is usually at $V_{DD}$, so body effect exists).\n*   $r_{o1}$ and $r_{o2}$ are the output resistances (channel-length modulation resistances) of $M_1$ and $M_2$ respectively.\n\n**Approximation**\nTypically, the term $(g_{m1} + g_{mb1})r_{o1}r_{o2}$ is much larger than $r_{o1} + r_{o2}$. Therefore, the output resistance can be approximated as:\n\n$$R_{out} \\approx (g_{m1} + g_{mb1})r_{o1}r_{o2}$$\n\nIf the body effect is neglected ($g_{mb1} = 0$), the expression simplifies to the standard cascode output resistance formula:\n\n$$R_{out} \\approx g_{m1}r_{o1}r_{o2}$$",
        "format": "markdown",
        "sha256": "6ec632c69221830ae939cf0444a729a5eb01da3c2984f48f0e0b68b18873471b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the PMOS stack, treats M1 as the cascode device, and gives the full output-resistance expression and appropriate approximation.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 10044,
        "total_tokens": 12182,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9237,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 10044,
        "total_tokens": 12182,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9237,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To find the output resistance $R_{\\text{out}}$ looking into the drain of transistor $M_1$, we can perform a small-signal analysis.\n\n**1. Circuit Analysis:**\n*   The circuit consists of two PMOS transistors, $M_2$ and $M_1$, stacked in series.\n*   $V_{DD}$, $V_{b1}$, and $V_{b2}$ are DC voltage sources, which act as AC grounds in small-signal analysis.\n*   We are looking for the resistance looking into the drain of $M_1$ (indicated by the arrow for $R_{\\text{out}}$).\n\n**2. Small-Signal Model:**\n*   **Transistor $M_2$:** The source is connected to $V_{DD}$ (AC ground) and the gate is connected to $V_{b2}$ (AC ground). Since the source-gate voltage $v_{sg2} = 0$ in small-signal, the dependent current source $g_{m2}v_{sg2}$ is zero. Therefore, looking into the drain of $M_2$ (at node $X$), we simply see the output resistance of the transistor, $r_{o2}$.\n*   **Transistor $M_1$:** The source of $M_1$ is connected to node $X$. From the analysis of $M_2$, the resistance at node $X$ to AC ground is $r_{o2}$. So, $M_1$ has a source degeneration resistance $R_S = r_{o2}$. The gate is connected to $V_{b1}$ (AC ground).\n\n**3. Calculation:**\nThe output resistance looking into the drain of a MOS transistor with a source resistance $R_S$ is given by the formula:\n$$R_{\\text{out}} = r_o + (1 + g_m r_o)R_S$$\n*(Note: If body effect is considered, $g_m$ is replaced by $(g_m + g_{mb})$)*.\n\nSubstituting the parameters for $M_1$ ($r_{o1}, g_{m1}$) and the source resistance $R_S = r_{o2}$:\n$$R_{\\text{out}} = r_{o1} + (1 + g_{m1} r_{o1}) r_{o2}$$\n$$R_{\\text{out}} = r_{o1} + r_{o2} + g_{m1} r_{o1} r_{o2}$$\n\nAssuming that the intrinsic gain $g_{m1} r_{o1} \\gg 1$, the term $g_{m1} r_{o1} r_{o2}$ dominates.\n\n**Final Answer:**\n$$R_{\\text{out}} \\approx g_{m1} r_{o1} r_{o2}$$\n\n(If body effect is included for $M_1$, the expression becomes $R_{\\text{out}} \\approx (g_{m1} + g_{mb1}) r_{o1} r_{o2}$).",
        "format": "markdown",
        "sha256": "d2c43d335849cb2c0cf413173fdf3ac447c3998ecb52c5cf2aa9914e736c3191"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, M1 as the cascode, and derives the correct output-resistance expression and approximation. Body effect is handled appropriately as optional.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 9151,
        "total_tokens": 11289,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8465,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 9151,
        "total_tokens": 11289,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8465,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-018-find-rout",
      "part": "part1",
      "question_number": 18,
      "question": "Find Rout in the figure.",
      "figures": [
        "tasks/part1-018-find-rout/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the step-by-step derivation to find the output resistance $R_{out}$.\n\n**1. Circuit Analysis**\nThe circuit shows two PMOS transistors, $M_1$ and $M_2$, stacked in series. This configuration is known as a **cascode** structure.\n*   **$M_2$**: The source is connected to $V_{DD}$ (AC ground) and the gate is connected to a bias voltage $V_{b2}$ (AC ground).\n*   **$M_1$**: The source is connected to the drain of $M_2$ (node $X$) and the gate is connected to a bias voltage $V_{b1}$ (AC ground).\n*   **$R_{out}$**: We are looking for the resistance looking into the drain of $M_1$.\n\n**2. Small-Signal Analysis**\nTo find $R_{out}$, we determine the small-signal resistance looking into the drain of $M_1$.\n\n*   **Step A: Resistance at Node X**\n    First, look into the drain of $M_2$ (node $X$) from the perspective of $M_1$'s source.\n    Since the source and gate of $M_2$ are connected to AC ground ($V_{DD}$ and $V_{b2}$ are constant DC voltages), the small-signal voltage $v_{gs2} = 0$. Consequently, the dependent current source $g_{m2}v_{gs2}$ is zero.\n    Therefore, looking into the drain of $M_2$, we simply see its output resistance, **$r_{o2}$**.\n\n*   **Step B: Resistance looking into Drain of $M_1$**\n    Now, the circuit can be modeled as transistor $M_1$ with a source degeneration resistance $R_S = r_{o2}$.\n    The formula for the output resistance looking into the drain of a MOSFET with a source resistance $R_S$ is:\n    $$R_{out} = r_{o1} + R_S + g_{m1}r_{o1}R_S$$\n    (Note: If the body effect is considered, $g_{m1}$ is replaced by $(g_{m1} + g_{mb1})$).\n\n    Substituting $R_S = r_{o2}$:\n    $$R_{out} = r_{o1} + r_{o2} + g_{m1}r_{o1}r_{o2}$$\n\n**3. Approximation**\nIn most practical MOSFET circuits, the intrinsic gain $g_{m}r_{o} \\gg 1$. Therefore, the term $g_{m1}r_{o1}r_{o2}$ dominates the expression.\n\n$$R_{out} \\approx g_{m1}r_{o1}r_{o2}$$\n\n**Final Answer:**\nThe output resistance is approximately:\n$$R_{out} \\approx g_{m1} r_{o1} r_{o2}$$\n\n(Or more precisely: $R_{out} = r_{o1} + r_{o2} + g_{m1}r_{o1}r_{o2}$)",
        "format": "markdown",
        "sha256": "b311a3a4558a37b273f2215525a8ce1b7388bf03eaa7fbdfb9c179d3250af3cb"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, assigns the cascode role to M1, and gives the correct output-resistance expression and approximation. Omitting body effect is allowed.",
          "golden_solution_sha256": "0e58951a444fd5eb5a81c93c3c94eef4ae9b6f921b6512a0c0fecf7f946efcb1",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 8473,
        "total_tokens": 10611,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7752,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2138,
        "output_tokens": 8473,
        "total_tokens": 10611,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7752,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, transistors $M_1$ and $M_2$ are **PMOS** transistors. This is indicated by the arrow on the source terminal pointing inward towards the channel, and the fact that the top transistor ($M_2$) has its source connected to the highest potential, $V_{DD}$.\n\nTo ensure that a PMOS transistor operates in the **saturation region** (also known as the active region), two conditions must be met:\n\n1.  **The transistor must be turned on (Strong Inversion):**\n    The source-gate voltage magnitude must exceed the threshold voltage magnitude.\n    $$V_{SG} > |V_{TH}|$$\n    For $M_2$:\n    $$V_{DD} - V_{b2} > |V_{THP}|$$\n\n2.  **The drain-source voltage must be large enough to pinch off the channel at the drain end:**\n    The magnitude of the source-drain voltage ($V_{SD}$) must be greater than or equal to the \"overdrive voltage\" ($V_{SG} - |V_{TH}|$).\n    $$V_{SD} \\ge V_{SG} - |V_{TH}|$$\n\n**Applying this to $M_2$:**\n\n*   **Source Voltage ($V_S$):** $V_{DD}$\n*   **Gate Voltage ($V_G$):** $V_{b2}$\n*   **Drain Voltage ($V_D$):** $V_X$ (the voltage at node X)\n\nSubstitute these into the saturation inequality:\n$$V_{SD2} \\ge V_{SG2} - |V_{THP}|$$\n$$(V_{DD} - V_X) \\ge (V_{DD} - V_{b2}) - |V_{THP}|$$\n\nSimplifying the inequality by canceling $V_{DD}$ from both sides:\n$$-V_X \\ge -V_{b2} - |V_{THP}|$$\n$$V_X \\le V_{b2} + |V_{THP}|$$\n\n**Conclusion:**\nTo ensure $M_2$ is in saturation, the voltage at node **X** ($V_X$) must be less than or equal to the gate bias voltage $V_{b2}$ plus the magnitude of the threshold voltage $|V_{THP}|$.\n\nAlternatively, you can state that the voltage drop across $M_2$ ($V_{DD} - V_X$) must be at least equal to its overdrive voltage ($V_{OV} = V_{DD} - V_{b2} - |V_{THP}|$).",
        "format": "markdown",
        "sha256": "40d79776cd571c36c6a825113a9fe1c356e5daa6fee51dd709b6c712dceb3b34"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies both devices as PMOS and gives M2's saturation condition in terms of VX and Vb2, but misses the essential relation VX = Vb1 + |VGS1| and therefore does not give the required condition on Vb1.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 5560,
        "total_tokens": 7666,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4984,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 5560,
        "total_tokens": 7666,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4984,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, **M2** is a PMOS transistor. To ensure it operates in the **saturation region** (also known as the active region), the following condition must be met regarding its terminal voltages:\n\nThe magnitude of the source-drain voltage ($V_{SD}$) must be greater than or equal to the magnitude of the overdrive voltage ($V_{OV} = V_{SG} - |V_{TH}|$).\n\nMathematically, for a PMOS transistor:\n$$V_{SD} \\ge V_{SG} - |V_{TH}|$$\n\nApplying this to transistor **M2**:\n*   **Source ($S$):** Connected to $V_{DD}$\n*   **Gate ($G$):** Connected to $V_{b2}$\n*   **Drain ($D$):** Connected to node $X$ (voltage $V_X$)\n\nSo, the voltages are:\n*   $V_{SG2} = V_{DD} - V_{b2}$\n*   $V_{SD2} = V_{DD} - V_X$\n\nSubstituting these into the saturation condition:\n$$V_{DD} - V_X \\ge (V_{DD} - V_{b2}) - |V_{TH2}|$$\n\nSimplifying the inequality (subtracting $V_{DD}$ from both sides and multiplying by -1, which flips the inequality sign):\n$$V_X \\le V_{b2} + |V_{TH2}|$$\n\n**In summary:**\nTo ensure M2 is in saturation, the voltage at node **X** ($V_X$) must be less than or equal to **$V_{b2} + |V_{TH2}|$**.\n\nPhysically, this means the drain voltage ($V_X$) must be low enough so that the voltage drop across the transistor ($V_{DD} - V_X$) is at least equal to its overdrive voltage ($V_{DD} - V_{b2} - |V_{TH2}|$). If $V_X$ rises too close to $V_{DD}$, M2 will enter the triode (linear) region.",
        "format": "markdown",
        "sha256": "db5d753605a2e68b773507f504a74a4450845e07809c3c935ed5adbd88f45bb1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M2 as PMOS and gives its saturation condition in terms of VX and Vb2, but misses that VX is set by Vb1 and therefore does not give the required condition on Vb1.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 7409,
        "total_tokens": 9515,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6939,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 7409,
        "total_tokens": 9515,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6939,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-019-ensure-m2-saturation",
      "part": "part1",
      "question_number": 19,
      "question": "How do we ensure that M2 is in saturation in the figure?",
      "figures": [
        "tasks/part1-019-ensure-m2-saturation/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, transistors $M_1$ and $M_2$ are PMOS transistors stacked in series. $M_2$ is the top transistor with its source connected to $V_{DD}$.\n\nTo ensure that a PMOS transistor operates in the **saturation region**, the source-drain voltage ($V_{SD}$) must be greater than or equal to the overdrive voltage ($V_{SG} - |V_{th}|$). Alternatively, this can be stated as the drain voltage being low enough relative to the gate voltage: $V_D \\le V_G + |V_{th}|$.\n\nApplying this to transistor $M_2$:\n\n1.  **Identify Terminals:**\n    *   Source ($S_2$): Connected to $V_{DD}$.\n    *   Gate ($G_2$): Connected to bias voltage $V_{b2}$.\n    *   Drain ($D_2$): Connected to node $X$ (voltage $V_X$).\n\n2.  **Saturation Condition:**\n    $$V_{SD2} \\ge V_{SG2} - |V_{thp2}|$$\n    where $|V_{thp2}|$ is the magnitude of the threshold voltage for $M_2$.\n\n3.  **Substitute Voltages:**\n    *   $V_{SD2} = V_{DD} - V_X$\n    *   $V_{SG2} = V_{DD} - V_{b2}$\n\n    So, the inequality becomes:\n    $$V_{DD} - V_X \\ge (V_{DD} - V_{b2}) - |V_{thp2}|$$\n\n4.  **Simplify:**\n    $$-V_X \\ge -V_{b2} - |V_{thp2}|$$\n    $$V_X \\le V_{b2} + |V_{thp2}|$$\n\n**Conclusion:**\nTo ensure $M_2$ is in saturation, the voltage at node $X$ ($V_X$) must be less than or equal to the gate bias voltage $V_{b2}$ plus the threshold voltage magnitude $|V_{thp}|$.\n\nIn terms of circuit design, since $V_X$ is the source voltage of $M_1$ (i.e., $V_X = V_{b1} + V_{SG1}$), this condition implies a relationship between the bias voltages $V_{b1}$ and $V_{b2}$. Specifically, $V_{b2}$ must be chosen high enough (close to $V_{DD}$) such that:\n$$V_{b2} \\ge V_X - |V_{thp2}|$$\nOr, substituting $V_X \\approx V_{b1} + |V_{thp1}| + V_{ov1}$ (where $V_{ov1}$ is the overdrive voltage of M1):\n$$V_{b2} \\ge V_{b1} + V_{ov1} + (|V_{thp1}| - |V_{thp2}|)$$\nAssuming matched transistors ($|V_{thp1}| = |V_{thp2}|$), the condition simplifies to **$V_{b2} \\ge V_{b1} + V_{ov1}$**. This ensures that the voltage drop across $M_2$ is sufficient to keep it in saturation.",
        "format": "markdown",
        "sha256": "e873d8a05eda010170789f1f37b6880c248468480ed374093b97a4922739391e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies both devices as PMOS, gives M2’s saturation condition, and relates VX to Vb1. The resulting matched-device condition, Vb2 − Vb1 ≥ M1’s overdrive, is equivalent to the golden solution.",
          "golden_solution_sha256": "519fe1851b4fd9a0e83d2b184c82583260701cb7382ec5e7c6bdd728b4cc9a0f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 6856,
        "total_tokens": 8962,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6107,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2106,
        "output_tokens": 6856,
        "total_tokens": 8962,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6107,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology, operation, and characteristics.\n\n### 1. Circuit Identification\nThe circuit shown is a **Cascode Amplifier** (specifically, a telescopic cascode stage) with an active current source load. It is a fundamental building block in analog CMOS design, widely used to achieve high voltage gain and high output impedance.\n\n### 2. Component Breakdown\n*   **$M_1$ (Input Transistor):** This is an NMOS transistor configured as a **Common-Source (CS)** amplifier. Its gate receives the input signal $V_{in}$. It is responsible for converting the input voltage into a small-signal drain current ($g_{m1}v_{in}$).\n*   **$M_2$ (Cascode Transistor):** This is an NMOS transistor configured as a **Common-Gate (CG)** stage. Its gate is connected to a constant DC bias voltage $V_{b1}$. It sits \"on top\" of $M_1$.\n*   **$I_1$ (Active Load):** This is a constant current source connected to the supply voltage $V_{DD}$. It acts as the load for the amplifier. In a real integrated circuit, this would typically be implemented using a PMOS transistor biased in saturation, which provides a high output resistance.\n*   **Node $X$:** This is the intermediate node connecting the drain of $M_1$ and the source of $M_2$.\n\n### 3. Circuit Operation\n*   **Signal Path:** The input signal $V_{in}$ modulates the current flowing through transistor $M_1$. Because $M_1$ and $M_2$ are in series, this current variation is passed through $M_2$ to the output node $V_{out}$.\n*   **Current Constraint:** The DC current flowing through the branch is set by the current source $I_1$ (and the biasing of $M_1$). For the circuit to operate as an amplifier, the transistors must be biased in the saturation region.\n*   **Role of $M_2$:** The cascode transistor $M_2$ holds the voltage at node $X$ (the drain of $M_1$) relatively constant. Since the gate of $M_2$ is at a fixed AC ground potential ($V_{b1}$), the source of $M_2$ (node $X$) presents a low impedance to the drain of $M_1$.\n\n### 4. Key Characteristics & Analysis\n\n**A. High Output Impedance**\nThe primary advantage of the cascode structure is a significant increase in output impedance.\n*   Looking down into the drain of $M_2$ (from node $V_{out}$), the output resistance is boosted by the intrinsic gain of $M_2$.\n*   $R_{out, cascode} \\approx g_{m2} r_{o2} r_{o1}$ (where $g_m$ is transconductance and $r_o$ is output resistance).\n*   The total output resistance at $V_{out}$ is the parallel combination of the cascode resistance and the output resistance of the current source $I_1$ (let's call it $R_{I1}$).\n    $$R_{total} = R_{I1} \\parallel (g_{m2} r_{o2} r_{o1})$$\n\n**B. High Voltage Gain**\nBecause the output impedance is very high, the voltage gain is significantly larger than that of a simple common-source amplifier.\n*   The transconductance of the entire cascode stage is approximately equal to that of the input transistor, $G_m \\approx g_{m1}$.\n*   The voltage gain $A_v$ is given by:\n    $$A_v = -G_m \\times R_{total} \\approx -g_{m1} [R_{I1} \\parallel (g_{m2} r_{o2} r_{o1})]$$\n*   If the current source $I_1$ is ideal (infinite resistance), the gain becomes extremely high: $A_v \\approx -g_{m1} g_{m2} r_{o1} r_{o2}$.\n\n**C. Reduced Miller Effect (High Bandwidth)**\nIn a standard common-source amplifier, the gate-drain capacitance ($C_{gd}$) of the transistor is multiplied by the gain (Miller effect), creating a large effective input capacitance that limits bandwidth.\n*   In this cascode circuit, the drain of $M_1$ (node $X$) is held at a relatively constant AC potential by the common-gate transistor $M_2$.\n*   This minimizes the voltage swing at the drain of $M_1$, effectively eliminating the Miller multiplication of $C_{gd1}$. This allows the amplifier to operate at much higher frequencies.\n\n### Summary\nThis circuit is a **high-gain, high-output-impedance amplifier**. It is designed to take a small input voltage signal at $V_{in}$ and produce a large amplified voltage signal at $V_{out}$, with improved frequency response compared to a single-transistor amplifier.",
        "format": "markdown",
        "sha256": "aa39bd8b6f9eba23cc7f6269eeee179b70c48dd5145e8508d39e1adb970ed8d3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression. The overstatement that node X is held nearly constant does not override the golden solution’s full-credit rule.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 5589,
        "total_tokens": 6654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4463,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 5589,
        "total_tokens": 6654,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4463,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology, operation, and characteristics.\n\n### 1. Circuit Identification\nThe circuit shown is an **NMOS Cascode Amplifier** with an ideal current source load.\n*   **$M_1$**: This is the input transistor configured as a **Common-Source (CS)** stage.\n*   **$M_2$**: This is the cascode transistor configured as a **Common-Gate (CG)** stage.\n*   **$I_1$**: This is an ideal current source acting as the active load.\n\n### 2. Circuit Operation\n*   **DC Path**: Current flows from the supply voltage $V_{DD}$, through the current source $I_1$, into the output node $V_{out}$, down through the drain-source of $M_2$, through the drain-source of $M_1$, and finally to ground.\n*   **Biasing**:\n    *   **$V_{in}$**: This is the input voltage. For the amplifier to work, $V_{in}$ must include a DC bias component sufficient to turn on $M_1$ and establish a drain current equal to $I_1$ (assuming saturation).\n    *   **$V_{b1}$**: This is a constant DC bias voltage applied to the gate of $M_2$. Its purpose is to keep $M_2$ turned on and in the saturation region. It sets the DC voltage at node $X$.\n\n### 3. Small-Signal Analysis\nThis circuit is designed to amplify small AC voltage signals applied at $V_{in}$.\n\n*   **Signal Path**:\n    1.  An input voltage signal $v_{in}$ at the gate of $M_1$ creates a small-signal drain current $i_{d1} = g_{m1}v_{in}$.\n    2.  This current flows into the source of the cascode transistor $M_2$. Since the gate of $M_2$ is at AC ground (constant DC bias $V_{b1}$), $M_2$ acts as a current buffer. It passes this current to its drain with a gain of approximately unity (ignoring body effect and output resistance for a moment).\n    3.  The current flows into the output node. Since the load is an ideal current source (infinite impedance), this small-signal current develops a large voltage swing at $V_{out}$.\n\n*   **Voltage Gain ($A_v$)**:\n    The voltage gain is given by $A_v = -G_m R_{out}$.\n    *   **Transconductance ($G_m$)**: The effective transconductance of the cascode stage is approximately that of the input transistor, $g_{m1}$.\n    *   **Output Resistance ($R_{out}$)**: The cascode structure significantly boosts the output impedance looking into the drain of $M_2$. The resistance looking down into the drain of $M_2$ is approximately $R_{down} \\approx g_{m2}r_{o2}r_{o1}$ (where $r_{o}$ is the output resistance of the transistors). The resistance looking up into the ideal current source is infinite ($\\infty$).\n    *   Therefore, the total output resistance is $R_{out} \\approx g_{m2}r_{o2}r_{o1}$.\n    *   **Gain Equation**:\n        $$A_v \\approx -g_{m1} (g_{m2} r_{o2} r_{o1})$$\n    This represents a very high voltage gain, roughly the square of the intrinsic gain ($g_m r_o$) of a single transistor.\n\n### 4. Key Advantages\n1.  **High Output Impedance**: The stacking of $M_2$ on top of $M_1$ creates a high impedance node at $V_{out}$, which is essential for achieving high voltage gain.\n2.  **Reduced Miller Effect**: In a simple common-source amplifier, the gate-drain capacitance ($C_{gd}$) is multiplied by the gain (Miller effect), limiting bandwidth. In this cascode circuit, the drain of $M_1$ (node $X$) is connected to the source of a common-gate transistor ($M_2$). The impedance at node $X$ is low (approximately $1/g_{m2}$). Consequently, the voltage gain from the gate of $M_1$ to node $X$ is small (approx -1), which minimizes the Miller multiplication of $C_{gd1}$. This results in a **higher bandwidth** and better frequency response compared to a simple common-source amplifier.\n3.  **Shielding**: $M_2$ shields the input transistor $M_1$ from large voltage swings at the output $V_{out}$, reducing the effect of channel-length modulation on the input stage.\n\n### 5. Constraints (Headroom)\nFor both transistors to remain in saturation (which is required for amplification):\n*   $V_X$ (voltage at node X) must be at least $V_{GS1} - V_{TH1}$ (overdrive voltage of $M_1$).\n*   $V_{out}$ must be at least $V_X + (V_{GS2} - V_{TH2})$.\nThis means the cascode stack requires more voltage headroom (minimum $V_{out}$) than a single transistor amplifier, which can be a limitation in low-voltage designs.",
        "format": "markdown",
        "sha256": "33584e036bca568482ffaa843b518c09e98c59499ea2be50d1952df57eff69e4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain expression. The node-X swing claim is inaccurate, but the golden solution’s full-credit rule applies.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 5316,
        "total_tokens": 6381,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 5316,
        "total_tokens": 6381,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-020-nmos-cascode-gain-stage",
      "part": "part1",
      "question_number": 20,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-020-nmos-cascode-gain-stage/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology, components, and operation.\n\n### 1. Circuit Identification\nThis circuit is a **Cascode Amplifier** (specifically an NMOS cascode) with an ideal current source load.\n\n### 2. Component Breakdown\n*   **$M_1$ (Input Transistor):** This is an NMOS transistor configured as a common-source amplifier. Its gate receives the input signal $V_{in}$, and its source is connected to ground. It is the primary transconductance device that converts the input voltage into a current.\n*   **$M_2$ (Cascode Transistor):** This is an NMOS transistor stacked on top of $M_1$. Its gate is connected to a fixed DC bias voltage, $V_{b1}$. It acts as a \"cascode\" device.\n*   **$I_1$ (Active Load):** This is an ideal current source connected to the supply rail $V_{DD}$. It provides the bias current for the circuit and acts as a load with theoretically infinite impedance.\n*   **$V_{out}$:** The output voltage is taken at the drain of $M_2$.\n*   **Node $X$:** The connection point between the drain of $M_1$ and the source of $M_2$.\n\n### 3. Circuit Operation & Analysis\n\n**DC Biasing:**\nFor the circuit to function as an amplifier, both transistors must be in the saturation region.\n*   The current source $I_1$ forces a specific current through the branch.\n*   The input DC bias voltage at $V_{in}$ must be set such that $M_1$ conducts this current $I_1$.\n*   The bias voltage $V_{b1}$ must be set high enough to keep $M_2$ turned on and in saturation ($V_{b1} > V_X + V_{TH}$).\n\n**Small-Signal Analysis (AC):**\n*   **Function:** The circuit amplifies the input voltage $V_{in}$.\n*   **Transconductance:** The input transistor $M_1$ generates a small-signal current $i_d = g_{m1} \\cdot v_{in}$.\n*   **Output Impedance ($R_{out}$):** The key feature of the cascode structure is its very high output impedance. Looking into the drain of $M_2$, the resistance is approximately:\n    $$R_{out} \\approx g_{m2} r_{o2} r_{o1}$$\n    (where $g_m$ is transconductance and $r_o$ is output resistance of the transistors). This is much larger than the output resistance of a simple common-source amplifier ($r_{o1}$).\n*   **Voltage Gain ($A_v$):** Since the load is an ideal current source (infinite impedance), the total impedance at the output node is dominated by the cascode stack's output resistance.\n    $$A_v = \\frac{V_{out}}{V_{in}} \\approx -g_{m1} \\cdot R_{out} \\approx -g_{m1} (g_{m2} r_{o2} r_{o1})$$\n    This results in a very high voltage gain, often referred to as the \"intrinsic gain\" squared.\n\n### 4. Key Advantages\n1.  **High Gain:** Due to the high output impedance provided by the cascode stacking ($M_2$ boosting the impedance of $M_1$).\n2.  **Reduced Miller Effect:** In a simple common-source amplifier, the capacitance between the gate and drain ($C_{gd}$) is multiplied by the gain, limiting bandwidth. In this cascode circuit, the drain of $M_1$ (Node $X$) is held at a relatively constant AC potential (a low-impedance node roughly equal to $1/g_{m2}$). This minimizes the voltage swing at the drain of $M_1$, significantly reducing the Miller effect and improving the high-frequency response (bandwidth).\n3.  **Shielding:** $M_2$ shields the input transistor $M_1$ from voltage fluctuations at the output node $V_{out}$.\n\n### 5. Disadvantages / Constraints\n*   **Voltage Headroom:** Stacking two transistors ($M_1$ and $M_2$) plus the current source requires a higher supply voltage ($V_{DD}$) to keep all devices in saturation. The minimum output voltage required is roughly $V_{out, min} \\approx V_{eff1} + V_{eff2}$ (where $V_{eff} = V_{GS} - V_{TH}$).",
        "format": "markdown",
        "sha256": "ce960d342c856107167ab832a959c5f85f614aa17e7dc8877983588e9ea78f92"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-source NMOS and M2 as the common-gate NMOS cascode, and gives the equivalent ideal-load gain. The node-X swing claim is imprecise, but the full-credit rule applies.",
          "golden_solution_sha256": "fa3ce3c10c3d0bf6258738fc6e9b064c896064cb851cd7f79a50e2fe2b3c822b",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 3991,
        "total_tokens": 5056,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2968,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1065,
        "output_tokens": 3991,
        "total_tokens": 5056,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2968,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**.\n\nHere is the breakdown of why:\n\n1.  **Stacked Transistors:** The circuit features two transistors, $M_1$ and $M_2$, stacked in series.\n2.  **Common-Source Stage ($M_1$):** The bottom transistor $M_1$ has its source connected to ground and its gate connected to the input signal $V_{in}$. This configuration acts as a common-source amplifier.\n3.  **Common-Gate Stage ($M_2$):** The top transistor $M_2$ has its gate connected to a constant bias voltage $V_{b1}$ and its source connected to the drain of $M_1$. This configuration acts as a common-gate amplifier.\n\nA **cascode amplifier** is defined precisely by this combination: a common-source stage feeding into a common-gate stage. This structure is used to increase gain, improve bandwidth, and reduce the Miller effect compared to a simple common-source amplifier.",
        "format": "markdown",
        "sha256": "c86bb039e2307480ac43f3639ddbf9fb7f3285c8d1264095c8dbb6e29285df13"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The circuit is not a cascode: M1 is a PMOS source follower, not a common-source stage. The answer misidentifies M1's connections and incorrectly concludes that the structure provides cascode behavior.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 893,
        "total_tokens": 2019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 893,
        "total_tokens": 2019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**.\n\nHere is the breakdown of why:\n\n1.  **Stacked Transistors:** The circuit features two transistors, $M_1$ and $M_2$, stacked in series.\n2.  **Common-Source Stage ($M_1$):** The bottom transistor $M_1$ has its source connected to ground and its gate connected to the input signal $V_{in}$. This configuration acts as a common-source amplifier.\n3.  **Common-Gate Stage ($M_2$):** The top transistor $M_2$ has its gate connected to a constant bias voltage $V_{b1}$ and its source connected to the drain of $M_1$. This configuration acts as a common-gate amplifier.\n\nA cascode amplifier is defined precisely by this combination: a common-source stage driving a common-gate stage. This structure is used to increase gain, bandwidth, and output impedance while reducing the Miller effect.",
        "format": "markdown",
        "sha256": "bb674f21bcd997234dac2859dc9f04cdf4a38d1ef6c35ce38a57648c9239b1a9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source stage, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 885,
        "total_tokens": 2011,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 885,
        "total_tokens": 2011,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-021-cascode-structure",
      "part": "part1",
      "question_number": 21,
      "question": "Is the circuit shown in the figure a cascode structure?",
      "figures": [
        "tasks/part1-021-cascode-structure/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit shown in the figure is a **cascode structure**.\n\nHere is the breakdown of why:\n\n1.  **Stacked Transistors:** The circuit features two transistors, $M_1$ and $M_2$, stacked in series.\n2.  **Common-Source Stage ($M_1$):** The bottom transistor $M_1$ has its source connected to ground and its gate connected to the input signal $V_{in}$. This configuration acts as a common-source amplifier.\n3.  **Common-Gate Stage ($M_2$):** The top transistor $M_2$ has its gate connected to a constant bias voltage $V_{b1}$ and its source connected to the drain of $M_1$. This configuration acts as a common-gate amplifier.\n\nA cascode amplifier is defined precisely by this combination: a common-source stage feeding into a common-gate stage. This structure is used to increase gain, bandwidth, and output impedance while reducing the Miller effect.",
        "format": "markdown",
        "sha256": "f69fb54d41efb2e477ec8bdb6957dfd699014e408f4636a510cda5933edd7252"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly calls the circuit a cascode. M1 is a PMOS source follower with its drain grounded, not a common-source stage, so the structure lacks cascode resistance boosting.",
          "golden_solution_sha256": "7f9e0f88c009a8a25ec2184287032d702e4ac63736a803d1b8f3b4092778054c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 886,
        "total_tokens": 2012,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1126,
        "output_tokens": 886,
        "total_tokens": 2012,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 669,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# The Miller Effect in a Cascode Amplifier\n\n## The Miller Effect — A Quick Recap\n\nIn a single common-source (or common-emitter) amplifier, the gate-drain capacitance **C_gd** bridges the input and the inverted output. Because the output voltage swings by **A_v × ΔV_in** in the opposite direction, the voltage *across* C_gd changes by **(1 + |A_v|) × ΔV_in**. This makes C_gd appear at the input as a much larger capacitance:\n\n$$C_{in,\\text{Miller}} = C_{gd} \\times (1 + |A_v|)$$\n\nThis multiplied capacitance creates a dominant low-frequency pole, severely limiting bandwidth.\n\n---\n\n## The Cascode Structure\n\nA cascode stacks two transistors:\n\n- **M1** — Common-source (input) transistor\n- **M2** — Common-gate (output) transistor, with its gate tied to a fixed bias voltage (AC ground)\n\nThe input is at the gate of M1, and the output is at the drain of M2.\n\n---\n\n## Why the Miller Effect Is Suppressed\n\nThe key is to look at the **gain across the feedback capacitor of the input transistor M1**, which is C_gd1.\n\n### 1. The gain of the first stage (M1) is only ≈ −1\n\nThe drain of M1 connects to the **source** of M2. The common-gate transistor M2 presents a very low input impedance at its source:\n\n$$R_{in,M2} \\approx \\frac{1}{g_{m2}}$$\n\nSo the voltage gain from the gate of M1 to the drain of M1 is:\n\n$$A_{v1} = -g_{m1} \\times \\frac{1}{g_{m2}} \\approx -1 \\quad (\\text{if } g_{m1} \\approx g_{m2})$$\n\n### 2. Miller multiplication is minimal\n\nSince the gain across M1 is only about **−1**, the Miller-multiplied capacitance at the input becomes:\n\n$$C_{in,\\text{Miller}} = C_{gd1} \\times (1 + |A_{v1}|) \\approx C_{gd1} \\times 2$$\n\nCompare this to a single common-source stage where |A_v| could be 50–100+, making the effective input capacitance **tens of times larger**.\n\n### 3. C_gd2 is not Miller-multiplied either\n\nThe second transistor M2 has its own C_gd2, but its gate is tied to **AC ground**. Therefore, C_gd2 simply appears as a capacitance from the output node to ground — there is no Miller multiplication because one terminal of the capacitor is at a fixed AC potential.\n\n---\n\n## Summary\n\n| | Common-Source | Cascode |\n|---|---|---|\n| Gain across C_gd1 | Large (−g_m · R_D) | ≈ −1 |\n| Miller factor (1 + \\|A_v\\|) | Very large (e.g., 50–100) | ≈ 2 |\n| Effective input capacitance | C_gs + C_gd(1 + \\|A_v\\|) | C_gs + 2·C_gd |\n| Bandwidth | Severely limited | Much higher |\n\n**In essence:** The cascode \"shields\" the input transistor from the high output voltage swing. The common-gate transistor M2 absorbs the large output voltage variation, keeping the drain voltage of M1 nearly constant. With almost no voltage swing across C_gd1, there is almost no Miller multiplication, and the input pole moves to a much higher frequency.",
        "format": "markdown",
        "sha256": "4dc5aba6fb085c3950a7779f3e59a242cd47a065ad5eae203e1e64620babbae7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance M1-drain/M2-source node and derives a gain across Cgd1 of about −1, giving roughly 2× rather than the large common-source Miller factor. The closing claim of almost no swing/Miller effect overstates the reduction, but the golden solution treats this as a minor flaw.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 1519,
        "total_tokens": 1543,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 714,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 1519,
        "total_tokens": 1543,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 714,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why the Miller Effect Is Less Pronounced in a Cascode\n\n## The Miller Effect in a Single Common-Source Stage\n\nIn a single common-source (CS) amplifier, the parasitic gate-drain capacitance **C_gd** bridges the input (gate) and the output (drain). Because the output voltage is an inverted, amplified copy of the input, the voltage *across* C_gd is much larger than the input voltage alone. This causes the effective input capacitance to be multiplied:\n\n$$C_{\\text{in, Miller}} = C_{gd} \\times (1 + |A_v|)$$\n\nwhere $A_v = -g_m r_o$ can be very large (e.g., −50 to −100). This massive capacitance creates a dominant low-frequency pole, severely limiting bandwidth.\n\n---\n\n## The Cascode Structure\n\nA cascode stacks two transistors:\n\n| Transistor | Configuration | Role |\n|---|---|---|\n| **M1** (bottom) | Common-Source (CS) | Receives the input signal at its gate |\n| **M2** (top) | Common-Gate (CG) | Its gate is tied to a fixed bias (AC ground); output is taken from its drain |\n\nThe critical internal node is **Node X** — the drain of M1, which is also the source of M2.\n\n---\n\n## Why the Miller Effect Is Suppressed\n\n### 1. The gain of M1 is very small (~1)\n\nM1's load is not a high impedance like $r_o$, but rather the **low input impedance of M2** (a common-gate stage), which is approximately:\n\n$$R_{\\text{load, M1}} \\approx \\frac{1}{g_{m2}}$$\n\nSo the voltage gain of the first stage (from gate of M1 to Node X) is:\n\n$$A_{v1} = \\frac{V_X}{V_{in}} \\approx -g_{m1} \\times \\frac{1}{g_{m2}} \\approx -1$$\n\nSince the gain across M1 is only about **−1**, the Miller multiplication of $C_{gd1}$ is minimal:\n\n$$C_{\\text{in, Miller}} = C_{gd1} \\times (1 + |A_{v1}|) \\approx C_{gd1} \\times (1 + 1) = 2\\,C_{gd1}$$\n\nCompare this to a single CS stage where the factor could be $1 + 50 = 51$. The input capacitance is dramatically smaller.\n\n### 2. C_gd2 does not experience Miller multiplication at all\n\nFor the top transistor M2, $C_{gd2}$ connects between:\n- **Drain** → the output node\n- **Gate** → AC ground (fixed bias voltage)\n\nSince one terminal of $C_{gd2}$ is at **AC ground**, there is no Miller multiplication. It simply appears as a parasitic capacitance at the output node, where it has little effect on the input-referred bandwidth.\n\n---\n\n## Summary\n\n| | Single CS Stage | Cascode |\n|---|---|---|\n| Gain across $C_{gd}$ | $-g_m r_o$ (large) | $\\approx -1$ (M1 only) |\n| Miller multiplication of $C_{gd1}$ | $\\times (1 + g_m r_o)$ — **huge** | $\\times (1 + 1) = 2$ — **negligible** |\n| $C_{gd2}$ | N/A | No Miller effect (gate at AC ground) |\n| **Resulting bandwidth** | **Low** | **High** |\n\n**In essence:** The cascode \"shields\" the input from the output by breaking the overall high gain into two stages. The first stage (M1) sees only a small voltage swing at its drain (Node X), so the Miller multiplication of $C_{gd1}$ is almost eliminated. The second stage (M2) provides the high voltage gain, but its $C_{gd2}$ is grounded at one terminal and cannot feed back to the input. The result is a high-gain amplifier with the bandwidth of a single transistor.",
        "format": "markdown",
        "sha256": "afc9ae65e414bab56cb733f361d004a6bdb3bd4b83f6b608e232ab2732160f12"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the low-impedance M1-drain/M2-source node and the resulting gain of about −1 across Cgd1, giving a Miller factor of roughly 2 rather than the full-stage gain. Calling the effect negligible or almost eliminated slightly overstates the reduction, but this is a minor flaw.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 2004,
        "total_tokens": 2028,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1079,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 2004,
        "total_tokens": 2028,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1079,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-022-explain-why-miller-effect-less-pronounced-cascode",
      "part": "part1",
      "question_number": 22,
      "question": "Explain why the Miller effect is less pronounced in a cascode.",
      "figures": [],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "# Why the Miller Effect Is Less Pronounced in a Cascode\n\n## The Miller Effect in a Single Common-Source Stage\n\nIn a simple common-source (CS) amplifier, the gate-drain capacitance **C_gd** bridges the input (gate) and the output (drain). Because the stage has a large inverting voltage gain **A_v = −g_m · R_D**, the Miller effect multiplies this capacitance at the input:\n\n$$C_{in,\\text{Miller}} = C_{gd} \\cdot (1 + |A_v|) = C_{gd} \\cdot (1 + g_m R_D)$$\n\nThis large effective capacitance creates a dominant low-frequency pole, severely limiting bandwidth.\n\n---\n\n## The Cascode Structure\n\nA cascode stacks two transistors:\n\n- **M1** — Common-source (input) transistor\n- **M2** — Common-gate (output) transistor, with its gate held at a fixed bias\n\nThe critical node is the **drain of M1**, which is also the **source of M2**.\n\n---\n\n## The Key Insight: Low Gain at the Internal Node\n\nThe Miller multiplication depends on the voltage gain **across the capacitor in question**. For the input transistor M1, the relevant capacitance is **C_gd1**, which sits between the gate of M1 (input) and the drain of M1 (internal node).\n\nThe voltage gain from the gate of M1 to its drain is:\n\n$$A_{v1} = -g_{m1} \\cdot R_{\\text{source of M2}}$$\n\nThe common-gate transistor M2 presents a very **low input impedance** at its source:\n\n$$R_{\\text{source of M2}} \\approx \\frac{1}{g_{m2}}$$\n\nTherefore:\n\n$$A_{v1} \\approx -g_{m1} \\cdot \\frac{1}{g_{m2}} \\approx -1$$\n\n(assuming matched transistors where $g_{m1} \\approx g_{m2}$)\n\n---\n\n## Result: Minimal Miller Multiplication\n\nSince the gain across C_gd1 is only about **unity**, the Miller-multiplied input capacitance becomes:\n\n$$C_{in,\\text{Miller}} = C_{gd1} \\cdot (1 + |A_{v1}|) \\approx C_{gd1} \\cdot (1 + 1) = 2\\,C_{gd1}$$\n\nCompare this to a single CS stage where the factor could be **50–100×** or more. The cascode reduces the Miller multiplication from a huge number down to just **2**.\n\n---\n\n## What About C_gd2?\n\nThe second transistor M2 does have a large voltage gain from its source to its drain, so C_gd2 *does* experience Miller multiplication. However, C_gd2 is connected between the **output node** and the low-impedance source of M2 — **not** the input. Its Miller effect appears at the output, where it has a much smaller impact on the overall bandwidth because the output node typically has a lower impedance or is not the bandwidth-limiting node.\n\n---\n\n## Summary\n\n| | Common-Source | Cascode |\n|---|---|---|\n| Gain across C_gd1 | $-g_m R_D$ (large) | $\\approx -1$ (unity) |\n| Miller factor | $1 + g_m R_D$ (large) | $\\approx 2$ (small) |\n| Input capacitance | Greatly increased | Barely increased |\n| Bandwidth | Severely limited | Much higher |\n\n**In essence:** The cascode \"shields\" the input from the output by inserting a common-gate stage that holds the drain of the input transistor at a nearly constant AC voltage. With almost no AC voltage swing across C_gd1, there is almost no Miller multiplication, and the input pole is pushed to a much higher frequency.",
        "format": "markdown",
        "sha256": "49a72b9b6bb85ceffa0603326480aa9cd46b7a288d7931a04dd06f34c1c66826"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "The central explanation is correct: M2 presents a low impedance at M1’s drain, giving roughly unity gain there and about a 2× Miller factor for Cgd1. However, the conclusion overstates this as almost no swing across Cgd1, and the optional Cgd2 discussion misidentifies its terminals; Cgd2 connects M2’s gate to its drain, not its source to the output.",
          "golden_solution_sha256": "0d298300029d3b4545999675d8ec4b4c83532fca89fa9878f9898848f75f534f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 1552,
        "total_tokens": 1576,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 24,
        "output_tokens": 1552,
        "total_tokens": 1576,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology and its operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **Common Source Amplifier with an Active Load**. This is a fundamental building block in analog integrated circuit design, often used as a gain stage in operational amplifiers.\n\n### 2. Component Analysis\n*   **$M_1$ (Top Transistor):**\n    *   **Type:** Based on the symbol (arrow pointing inward towards the channel), this is a **PMOS** transistor.\n    *   **Configuration:** Its source is connected to the supply voltage $V_{DD}$, and its gate is connected to a constant bias voltage $V_{b2}$.\n    *   **Function:** Because the gate voltage $V_{b2}$ is fixed, $M_1$ operates as a **constant current source** (also known as an active load). It provides a high impedance load for the amplifier, which allows for high voltage gain.\n\n*   **$M_2$ (Bottom Transistor):**\n    *   **Type:** While the symbol is slightly stylized, in this standard configuration, this is typically an **NMOS** transistor acting as the driver. (Note: If the arrow is interpreted as pointing inward like $M_1$, it would be a PMOS, creating a source-follower configuration, but the Common Source topology is the standard interpretation for this layout).\n    *   **Configuration:** Its gate is connected to the input signal $V_{in}$. Its source is connected to a bias voltage $V_{b1}$ (which is likely ground or a negative supply rail, serving as the common terminal). Its drain is connected to the output node.\n    *   **Function:** This is the amplifying device. It converts the input voltage variations into current variations.\n\n*   **$V_{out}$:** The output voltage is taken at the drain of $M_2$ (which is also the drain of $M_1$).\n\n### 3. Circuit Operation\n*   **DC Bias:** The transistor $M_1$ is biased by $V_{b2}$ to conduct a specific constant current, $I_{bias}$. This current flows through $M_2$. The input DC level at $V_{in}$ is set such that $M_2$ also conducts this same current $I_{bias}$, establishing the DC operating point at $V_{out}$.\n*   **AC Signal (Amplification):** When a small AC signal is applied to $V_{in}$, it modulates the gate-source voltage ($V_{GS}$) of $M_2$. This changes the conductance of $M_2$.\n    *   Since $M_1$ acts as a stiff current source (high impedance), it tries to keep the current constant.\n    *   Therefore, the small changes in current caused by $M_2$ result in large voltage swings at the high-impedance node $V_{out}$.\n\n### 4. Key Characteristics\n*   **Voltage Gain ($A_v$):** The circuit provides high voltage gain. The small-signal voltage gain is approximately:\n    $$A_v \\approx -g_{m2} (r_{o1} \\parallel r_{o2})$$\n    Where:\n    *   $g_{m2}$ is the transconductance of the input transistor $M_2$.\n    *   $r_{o1}$ and $r_{o2}$ are the output resistances (due to channel length modulation) of $M_1$ and $M_2$, respectively.\n    *   The negative sign indicates that the amplifier is **inverting** (a positive change at input leads to a negative change at output).\n\n*   **Input Impedance:** Very high (ideally infinite), as the input is connected to the gate of a MOSFET.\n*   **Output Impedance:** High, determined by the parallel combination of the output resistances of the two transistors ($r_{o1} \\parallel r_{o2}$).\n\n### Summary\nThis is a high-gain, inverting amplifier stage where $M_2$ acts as the transconductance amplifier and $M_1$ acts as a high-impedance active load to maximize the gain.",
        "format": "markdown",
        "sha256": "73ea992a40d67da004dad8c58718963532632dc3bbf843d01bf0acc7ef6c5b6b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer places Vin at the gate of M2 and identifies the circuit as an inverting common-source stage. The actual circuit is common-gate, with Vin at M2's source, so its topology, gain polarity, and input resistance are all misidentified.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 20035,
        "total_tokens": 21028,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 20035,
        "total_tokens": 21028,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 19113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the topology and its operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **Common Gate Amplifier with an Active Load**. It consists of two MOSFET transistors, $M_1$ and $M_2$.\n\n### 2. Component Analysis\n\n*   **Transistor $M_1$ (PMOS Active Load):**\n    *   **Symbol:** The arrow on the source terminal points inward (towards the channel), which is the standard symbol for a **PMOS** transistor.\n    *   **Connections:**\n        *   **Source:** Connected to the supply voltage $V_{DD}$.\n        *   **Gate:** Connected to a constant bias voltage $V_{b2}$.\n        *   **Drain:** Connected to the output node $V_{out}$.\n    *   **Function:** Since the gate voltage $V_{b2}$ is constant, $M_1$ operates as a **constant current source** (assuming it is in saturation). This configuration is known as an \"active load.\" It provides a high impedance at the output node, which is desirable for achieving high voltage gain.\n\n*   **Transistor $M_2$ (NMOS Driver):**\n    *   **Symbol:** The structure at the bottom (parallel lines) represents the gate oxide capacitor, indicating the gate terminal. The arrow on the terminal connected to $V_{in}$ likely represents the source/bulk terminal. Given the circuit topology (drain connected to the PMOS load), this must be an **NMOS** transistor to sink current. (Note: In some schematic conventions, the arrow on the bulk terminal points inward for an NMOS).\n    *   **Connections:**\n        *   **Gate:** Connected to a constant bias voltage $V_{b1}$. This sets the DC operating point and acts as an AC ground.\n        *   **Source:** Connected to the input signal $V_{in}$.\n        *   **Drain:** Connected to the output node $V_{out}$ (common node with $M_1$).\n    *   **Function:** This is the amplifying device. Because the input is applied to the source and the gate is held at a fixed bias, it is in a **Common Gate** configuration.\n\n### 3. Circuit Operation\n\n*   **DC Bias:**\n    *   $M_1$ sets a reference current $I_{bias}$ determined by $V_{DD}$, $V_{b2}$, and the transistor parameters.\n    *   $M_2$ must conduct this same current. The bias voltage $V_{b1}$ and the DC level of $V_{in}$ are chosen to keep $M_2$ in the saturation region. Current flows from $V_{DD}$, through $M_1$, to the node $V_{out}$, and then through $M_2$ to the input source $V_{in}$.\n\n*   **AC Signal (Small Signal Analysis):**\n    *   **Input:** The signal $v_{in}$ is applied to the source of $M_2$.\n    *   **Output:** The amplified signal $v_{out}$ is taken at the drain.\n    *   **Gain:** The Common Gate amplifier is a **non-inverting** amplifier. When the input voltage $V_{in}$ increases, the source-gate voltage $V_{GS}$ decreases ($V_G$ is fixed), which reduces the drain current. A reduction in current flowing through the active load $M_1$ causes less voltage drop across it, raising the output voltage $V_{out}$.\n    *   **Voltage Gain ($A_v$):** The approximate small-signal voltage gain is given by:\n        $$A_v \\approx g_{m2} (r_{o1} \\parallel r_{o2})$$\n        where $g_{m2}$ is the transconductance of $M_2$, and $r_{o1}, r_{o2}$ are the output resistances of $M_1$ and $M_2$ respectively.\n\n### 4. Key Characteristics\n*   **Low Input Impedance:** The input impedance looking into the source of $M_2$ is approximately $1/g_{m2}$. This makes it suitable for matching with low-impedance sources (like cables).\n*   **High Output Impedance:** The output impedance is high, determined by the parallel combination of the output resistances of the two transistors ($r_{o1} \\parallel r_{o2}$).\n*   **Non-inverting:** The output signal is in phase with the input signal.\n*   **Good High-Frequency Response:** Common gate stages are often used in high-frequency applications (like RF amplifiers) because they avoid the Miller effect capacitance multiplication seen in Common Source amplifiers.",
        "format": "markdown",
        "sha256": "32b63e9a2a75ae7686f0fb4451a94e5af2547ad33065ccc3eb764308719e6c3a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate NMOS stage with a PMOS current-source load, places the input at M2’s source, and gives the non-inverting gain and low input resistance. The stated gain matches the required approximation.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 17115,
        "total_tokens": 18108,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16069,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 17115,
        "total_tokens": 18108,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 16069,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-023-common-gate-pmos-load",
      "part": "part1",
      "question_number": 23,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-023-common-gate-pmos-load/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the topology and its operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **Common Source Amplifier with an Active Load** (specifically, a PMOS current source load). This is a fundamental building block in analog CMOS integrated circuit design, used to achieve high voltage gain.\n\n### 2. Component Analysis\n\n*   **Transistor $M_1$ (PMOS Active Load):**\n    *   **Type:** The symbol shows the arrow pointing inward on the source terminal (connected to $V_{DD}$), which identifies it as a **PMOS** transistor.\n    *   **Configuration:**\n        *   **Source:** Connected to the supply voltage $V_{DD}$.\n        *   **Gate:** Connected to a constant bias voltage $V_{b2}$.\n        *   **Drain:** Connected to the output node $V_{out}$.\n    *   **Function:** Since the gate voltage $V_{b2}$ is constant, $M_1$ is biased to operate in the saturation region. It acts as a **constant current source** (or active load). This provides a very high small-signal output resistance ($r_{o1}$), which is crucial for achieving high voltage gain.\n\n*   **Transistor $M_2$ (NMOS Driver):**\n    *   **Type:** Although the symbol is drawn slightly non-standardly, in this topology (pull-down network), it functions as an **NMOS** transistor.\n    *   **Configuration:**\n        *   **Gate:** Connected to the input signal $V_{in}$. (The line from $V_{in}$ leads to the gate structure).\n        *   **Source:** Connected to the bias voltage $V_{b1}$ (which is typically Ground or $V_{SS}$).\n        *   **Drain:** Connected to the output node $V_{out}$.\n    *   **Function:** This is the amplifying device. It converts the input voltage variations at the gate into current variations flowing through the channel.\n\n### 3. Circuit Operation\n\n*   **Biasing:**\n    *   $V_{b2}$ sets the DC bias current for the entire stage. The current flowing through $M_1$ is determined by this voltage.\n    *   $V_{b1}$ sets the source potential of $M_2$. If $V_{b1} = 0$ (Ground), it's a standard configuration.\n    *   The DC operating point is established where the current sourced by $M_1$ equals the current sunk by $M_2$.\n\n*   **Signal Amplification:**\n    *   When the input voltage $V_{in}$ increases, the gate-source voltage ($V_{GS}$) of $M_2$ increases.\n    *   This causes $M_2$ to conduct more current (attempting to pull more current from the node $V_{out}$ to $V_{b1}$).\n    *   Since $M_1$ acts as a constant current source, it cannot supply this extra current instantly. Consequently, the output node $V_{out}$ is discharged, causing the output voltage to drop.\n    *   Conversely, if $V_{in}$ decreases, $M_2$ conducts less current, and the constant current from $M_1$ charges the output node, causing $V_{out}$ to rise.\n    *   This results in an **inverting amplifier** (180° phase shift).\n\n### 4. Key Characteristics\n\n*   **Voltage Gain ($A_v$):**\n    The circuit provides high voltage gain because the load is a high-impedance current source rather than a simple resistor. The small-signal voltage gain is approximately:\n    $$A_v \\approx -g_{m2} (r_{o1} \\parallel r_{o2})$$\n    Where:\n    *   $g_{m2}$ is the transconductance of the input transistor $M_2$.\n    *   $r_{o1}$ and $r_{o2}$ are the output resistances (channel length modulation resistances) of $M_1$ and $M_2$, respectively.\n    *   The negative sign indicates the phase inversion.\n\n*   **Input Impedance:** Very high (looking into the gate of $M_2$).\n*   **Output Impedance:** High ($r_{o1} \\parallel r_{o2}$).",
        "format": "markdown",
        "sha256": "5aa6f918f5135e7064d5f0eebf2e8ec5f17bc6a0a23c1013d0c6e0f378835039"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It places Vin at M2's gate and identifies a common-source stage, but the circuit is a common-gate NMOS stage with Vin at M2's source; its gain is non-inverting and its input resistance is low.",
          "golden_solution_sha256": "bef1a8379b057bee5021488ff4aa65884dec1cb905b95a6d1d764f0128473407",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 14893,
        "total_tokens": 15886,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13925,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 993,
        "output_tokens": 14893,
        "total_tokens": 15886,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13925,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, we can determine the number of poles by analyzing the independent energy storage elements (capacitors) and the nodes in the small-signal model.\n\n1.  **Identify the Circuit Topology:** The circuit shows a MOSFET amplifier. $M_1$ is an NMOS transistor configured as a common-source amplifier (source is grounded). $M_2$ is a PMOS transistor acting as an active load. The gate of $M_2$ is connected to a DC bias (indicated by the ground symbol on the left, which represents an AC ground), and its source is connected to $V_{DD}$ (AC ground).\n\n2.  **Identify the Nodes:**\n    *   **Input Node (Gate of $M_1$):** Let's call the voltage at this node $V_x$. This node is connected to $V_{in}$ through resistor $R_S$.\n    *   **Output Node (Drain of $M_1$ and Drain of $M_2$):** This is labeled $V_{out}$. Let's call the voltage $V_y$.\n\n3.  **Analyze Capacitors:**\n    *   **$C_{GS}$:** Connected between the gate of $M_1$ ($V_x$) and ground.\n    *   **$C_{GD}$:** Connected between the gate of $M_1$ ($V_x$) and the drain of $M_1$ ($V_y$).\n    *   **$C_{DB}$:** Connected between the drain of $M_1$ ($V_y$) and ground.\n    *   **$C_{GD2}$:** Connected between the gate of $M_2$ (AC ground) and the drain of $M_2$ ($V_y$). Effectively, this is a capacitor from $V_y$ to ground.\n    *   **$C_{DB2}$:** Connected between the drain of $M_2$ ($V_y$) and $V_{DD}$ (AC ground). Effectively, this is a capacitor from $V_y$ to ground.\n\n4.  **Determine Independent State Variables:**\n    *   At the output node ($V_y$), the capacitors $C_{DB}$, $C_{GD2}$, and $C_{DB2}$ are all connected in parallel to AC ground. They can be combined into a single equivalent output capacitance $C_{out} = C_{DB} + C_{GD2} + C_{DB2}$.\n    *   At the input node ($V_x$), we have $C_{GS}$ to ground and $C_{GD}$ connecting to the output node.\n    *   The voltage across $C_{GD}$ is dependent on the voltages at the input and output nodes ($V_x - V_y$).\n    *   Therefore, the circuit dynamics are determined by the voltages at two independent nodes: the input node (Gate of $M_1$) and the output node (Drain of $M_1$).\n\nSince there are two independent nodes with capacitance, the transfer function of the circuit will be of the second order (denominator will be a quadratic polynomial in $s$).\n\n**Conclusion:**\nThe circuit has **2** poles. One pole is associated with the input node (formed by $R_S$ and the input capacitance) and the other pole is associated with the output node (formed by the output resistance and the total output capacitance).",
        "format": "markdown",
        "sha256": "89e397a5d1936d26e19875db4c925ba5cea7b00031b5fae0bafd734e8fc14f92"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the two independent dynamic nodes—the M1 gate and output—and assigns the capacitors to the appropriate nodes, yielding two poles.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 9605,
        "total_tokens": 11064,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 9605,
        "total_tokens": 11064,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8854,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the number of poles in the circuit, we need to identify the number of independent energy storage elements (capacitors) that can store charge independently. This is equivalent to finding the number of independent nodes in the small-signal model that have capacitance associated with them.\n\n1.  **Identify the nodes:**\n    *   **Input Node (Gate of $M_1$):** Let's call this node $X$. It is connected to $V_{in}$ through resistor $R_S$.\n    *   **Output Node (Drain of $M_1$ and Drain of $M_2$):** Let's call this node $Y$ (labeled $V_{out}$).\n    *   **AC Ground:** The source of $M_1$, the gate of $M_2$ (connected to the ground symbol), and the supply rails (top battery symbols) are all at AC ground.\n\n2.  **Analyze the capacitors and their connections:**\n    *   **$C_{GS}$:** Connected between the Gate of $M_1$ (Node $X$) and Ground.\n    *   **$C_{GD}$:** Connected between the Gate of $M_1$ (Node $X$) and the Drain of $M_1$ (Node $Y$).\n    *   **$C_{DB}$:** Connected between the Drain of $M_1$ (Node $Y$) and Ground.\n    *   **$C_{DB2}$:** Connected between the Drain of $M_2$ (Node $Y$) and the supply rail (AC Ground).\n    *   **$C_{GD2}$:** Connected between the Gate of $M_2$ and the Drain of $M_2$ (Node $Y$). Since the Gate of $M_2$ is connected to ground, this capacitor is effectively connected between Node $Y$ and Ground.\n\n3.  **Simplify the circuit:**\n    *   At the output node ($V_{out}$), the capacitors $C_{DB}$, $C_{DB2}$, and $C_{GD2}$ are all connected in parallel to ground. They can be combined into a single equivalent capacitor $C_{out} = C_{DB} + C_{DB2} + C_{GD2}$.\n    *   At the input node (Gate of $M_1$), we have capacitor $C_{GS}$ to ground.\n    *   There is a feedback capacitor $C_{GD}$ connecting the input node and the output node.\n\n4.  **Count the poles:**\n    *   The circuit effectively has two main nodes with capacitance: the input node (Gate of $M_1$) and the output node (Drain of $M_1$).\n    *   A circuit with two independent dynamic nodes (nodes with capacitance) will have a second-order transfer function.\n    *   Therefore, there are **2 poles**.\n\nOne pole is primarily associated with the input node (determined by $R_S$ and the input capacitance), and the other pole is primarily associated with the output node (determined by the output resistance of the amplifier stage and the total output capacitance). The capacitor $C_{GD}$ couples these two nodes but does not add a third pole.\n\n**Answer:** 2",
        "format": "markdown",
        "sha256": "940a2c919933d3b80de2ba3ea956779ebef9b81777babe544a293e1962d7137b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the two dynamic nodes—the gate of M1 and the output—and assigns the capacitors to the proper nodes. It correctly concludes that CGD couples the nodes without adding a third pole.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 8619,
        "total_tokens": 10078,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 8619,
        "total_tokens": 10078,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-024-many-poles-have",
      "part": "part1",
      "question_number": 24,
      "question": "How many poles does the circuit shown in the figure have?",
      "figures": [
        "tasks/part1-024-many-poles-have/figure-18.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, we can determine the number of poles by analyzing the independent energy storage elements (capacitors) and the nodes in the small-signal model.\n\n1.  **Identify the Nodes:**\n    *   **Input Node (Gate of $M_1$):** This node is connected to the input voltage $V_{in}$ through resistor $R_S$. It has a capacitance $C_{GS}$ to ground and a capacitance $C_{GD}$ connecting it to the output node.\n    *   **Output Node ($V_{out}$, Drain of $M_1$ and $M_2$):** This node connects the drain of $M_1$ and the drain of $M_2$.\n    *   **Ground/AC Ground Nodes:** The source of $M_1$, the source of $M_2$ (connected to VDD, which is AC ground), and the gate of $M_2$ (connected to a bias voltage/ground) are all at AC ground.\n\n2.  **Analyze Capacitors:**\n    *   $C_{GS}$: Connected between the input node (Gate of $M_1$) and ground.\n    *   $C_{GD}$: Connected between the input node (Gate of $M_1$) and the output node ($V_{out}$).\n    *   $C_{DB}$: Connected between the output node and ground.\n    *   $C_{DB2}$: Connected between the output node (Drain of $M_2$) and AC ground (VDD).\n    *   $C_{GD2}$: Connected between the gate of $M_2$ (which is at AC ground) and the drain of $M_2$ (output node). So, it is effectively between the output node and ground.\n\n3.  **Simplify the Circuit:**\n    *   The capacitors $C_{DB}$, $C_{DB2}$, and $C_{GD2}$ are all connected in parallel between the output node $V_{out}$ and ground. They can be combined into a single equivalent load capacitance $C_L = C_{DB} + C_{DB2} + C_{GD2}$.\n    *   The circuit effectively consists of two main nodes with capacitance: the input node (Gate of $M_1$) and the output node ($V_{out}$).\n    *   The capacitor $C_{GD}$ couples these two nodes.\n\n4.  **Determine the Order of the System:**\n    *   The circuit has two independent dynamic nodes (the gate of $M_1$ and the drain of $M_1$).\n    *   Writing the nodal equations for these two nodes will result in a system of two linear differential equations.\n    *   The characteristic equation (denominator of the transfer function) will be a quadratic polynomial in $s$ (i.e., $as^2 + bs + c = 0$).\n    *   A quadratic equation has two roots, which correspond to the poles of the system.\n\nTherefore, the circuit has **2** poles.",
        "format": "markdown",
        "sha256": "5dda8264edde4fec1e0b710d987a4bf701b1275a792b3e071c0f056fedb61972"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the two dynamic nodes—the M1 gate and output—and assigns the capacitors to the appropriate nodes, yielding two poles.",
          "golden_solution_sha256": "a186c7d78b22ed309b07c9b6c97e61997ddf23f0ee23de6faa3536cb2c682d8c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 10464,
        "total_tokens": 11923,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9788,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1459,
        "output_tokens": 10464,
        "total_tokens": 11923,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9788,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components, topology, and functionality.\n\n### 1. Component Identification\n*   **$V_{DD}$**: The positive power supply voltage.\n*   **$R_D$**: A drain resistor acting as a load.\n*   **$M_1$ and $M_2$**: Two N-channel MOSFETs (NMOS transistors). We can identify them as NMOS because the arrow on the source terminal points outward.\n*   **$V_{in}$**: The input voltage signal.\n*   **$V_{out}$**: The output voltage signal.\n\n### 2. Circuit Topology\nThe circuit is configured as a **resistive-load NMOS inverter** with a specific modification: the pull-down network consists of two transistors stacked in series.\n\n*   **Stacked Transistors:** Transistors $M_1$ and $M_2$ are connected in series. The source of the top transistor ($M_2$) is connected to the drain of the bottom transistor ($M_1$).\n*   **Common Gate Drive:** The gates of both $M_1$ and $M_2$ are tied together and connected to the input voltage $V_{in}$.\n*   **Load:** The drain of the top transistor ($M_2$) is connected to $V_{DD}$ through the resistor $R_D$. The output $V_{out}$ is taken from this node.\n*   **Ground:** The source of the bottom transistor ($M_1$) is connected to ground.\n\n### 3. Functional Analysis\n\nThis circuit can be analyzed from both digital and analog perspectives.\n\n#### A. Digital Logic Perspective (Inverter / NOT Gate)\nThe circuit functions as a logic inverter, but with a \"weaker\" pull-down network due to the series transistors.\n\n*   **Input Low ($V_{in} < V_{th}$):**\n    *   When the input voltage is below the threshold voltage ($V_{th}$), both transistors $M_1$ and $M_2$ are in the **cutoff region** (OFF).\n    *   No current flows through the resistor $R_D$ ($I_D \\approx 0$).\n    *   Therefore, there is no voltage drop across $R_D$, and **$V_{out} \\approx V_{DD}$** (Logic High).\n\n*   **Input High ($V_{in} > V_{th}$):**\n    *   When the input voltage is high, both transistors turn **ON**.\n    *   Current flows from $V_{DD}$, through $R_D$, through $M_2$, through $M_1$, to ground.\n    *   The transistors act as a closed switch (with some on-resistance). The output voltage drops towards ground.\n    *   **$V_{out} \\approx 0$ V** (Logic Low), assuming the on-resistance of the transistors is much smaller than $R_D$.\n\n**Note on Series Connection:** Connecting two transistors in series effectively increases the total channel length ($L_{total} \\approx L_1 + L_2$). This increases the on-resistance of the pull-down path compared to a single transistor. This might be done to handle higher voltages (stacking increases breakdown voltage) or to model a long-channel device.\n\n#### B. Analog Perspective (Amplifier)\nThe circuit acts as a **Common-Source Amplifier**.\n\n*   **Gain:** The voltage gain $A_v$ is approximately $-g_{m(eff)} \\cdot R_D$ (ignoring output resistance of the transistors for simplicity).\n*   **Effect of Stacking:**\n    *   Because the transistors are in series and driven by the same gate voltage, the effective transconductance ($g_m$) of the stack is lower than that of a single wide transistor.\n    *   The output impedance of the transistor stack is higher, which can improve the amplifier's linearity and output swing in certain designs.\n    *   **Body Effect:** For transistor $M_2$, the source is not at ground potential (it's at the drain potential of $M_1$). Assuming the substrate is grounded, $M_2$ will experience the **body effect**, which increases its threshold voltage ($V_{th}$). This makes $M_2$ harder to turn on than $M_1$.\n\n### Summary\nThe circuit is a **stacked NMOS inverter**. It takes an input $V_{in}$ and produces an inverted output $V_{out}$. The use of two series transistors ($M_1, M_2$) with common gates effectively creates a single transistor with a longer channel length, which increases the resistance of the pull-down path and the breakdown voltage capability.",
        "format": "markdown",
        "sha256": "16033dfe4b7f3f74be838f4098dac98e0ec875a56d7ae8993be693a27ba1c6bc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate series NMOS pair and states that it behaves like a transistor with effective channel length approximately L1 + L2, matching the essential answer.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 6381,
        "total_tokens": 7512,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5329,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 6381,
        "total_tokens": 7512,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5329,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of its components, topology, and function.\n\n### 1. Circuit Identification\nThe circuit is a **Resistive-Load NMOS Inverter** with a specific pull-down network configuration. It consists of a passive load (resistor) and an active pull-down network made of two transistors.\n\n### 2. Component Breakdown\n*   **$V_{DD}$**: The positive power supply voltage.\n*   **$R_D$**: A load resistor connected between the power supply and the output node.\n*   **$M_1$ and $M_2$**: Two N-channel MOSFETs (NMOS transistors).\n    *   **$M_1$**: The bottom transistor. Its source is connected to ground, and its gate is connected to the input $V_{in}$.\n    *   **$M_2$**: The top transistor. Its drain is connected to the output node, and its gate is also connected to the input $V_{in}$.\n*   **$V_{in}$**: The input voltage signal.\n*   **$V_{out}$**: The output voltage signal.\n\n### 3. Topology Analysis\n*   **Series Connection (Stacking):** The transistors $M_1$ and $M_2$ are connected in series (stacked). The drain of $M_1$ is connected to the source of $M_2$.\n*   **Gate Connection:** The gates of both transistors ($M_1$ and $M_2$) are tied together and connected to the input $V_{in}$. This means both transistors are driven by the same control signal.\n\n### 4. Circuit Operation\nThe circuit operates as a switch controlled by $V_{in}$:\n\n*   **Case 1: Input is Low ($V_{in} < V_{th}$)**\n    *   When the input voltage is below the threshold voltage ($V_{th}$) of the transistors, both $M_1$ and $M_2$ are in the **Cutoff region (OFF)**.\n    *   No current flows from $V_{DD}$ to ground ($I_D = 0$).\n    *   Consequently, there is no voltage drop across the resistor $R_D$.\n    *   **Output:** $V_{out} = V_{DD}$ (Logic High).\n\n*   **Case 2: Input is High ($V_{in} > V_{th}$)**\n    *   When the input voltage is high, both transistors turn **ON**.\n    *   Current flows from $V_{DD}$, through $R_D$, through the series combination of $M_2$ and $M_1$, to ground.\n    *   This current creates a voltage drop across $R_D$ ($V_{drop} = I \\cdot R_D$).\n    *   Assuming the on-resistance of the transistors is much smaller than $R_D$, the output voltage is pulled down close to ground.\n    *   **Output:** $V_{out} \\approx 0$ V (Logic Low).\n\n### 5. Functional Conclusion\n*   **Logic Function:** The circuit acts as a **NOT gate (Inverter)**.\n    *   Input Low $\\rightarrow$ Output High\n    *   Input High $\\rightarrow$ Output Low\n    *   Boolean expression: $V_{out} = \\overline{V_{in}}$\n\n*   **Equivalent Transistor:** Connecting two identical MOSFETs in series with their gates tied together is electrically equivalent to a single MOSFET with a **longer channel length** ($L_{total} = L_1 + L_2$). This configuration increases the total on-resistance of the pull-down path compared to a single transistor, which would result in a slower discharge of the output node or a higher \"low\" output voltage level if $R_D$ is not sufficiently large. Additionally, due to the **body effect**, the threshold voltage of the top transistor ($M_2$) will be higher than that of the bottom transistor ($M_1$) because the source of $M_2$ is at a potential higher than ground.",
        "format": "markdown",
        "sha256": "99f0875915a70c929f8ac8ca608d8947895ec4320b40b95828046e50032fdcc5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the series NMOS devices with tied gates and states that they approximate a single device with effective channel length L1 + L2. The inverter discussion and body-effect note do not undermine this central conclusion.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 4746,
        "total_tokens": 5877,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3832,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 4746,
        "total_tokens": 5877,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3832,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-025-series-nmos-effective-long-channel",
      "part": "part1",
      "question_number": 25,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-025-series-nmos-effective-long-channel/figure-19.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification\nThe circuit is a **Resistive-Load NMOS Inverter** (or Common-Source Amplifier) with a specific modification: the pull-down network consists of **two NMOS transistors ($M_1$ and $M_2$) connected in series** (stacked), with their gates tied together.\n\n### 2. Component Breakdown\n*   **$V_{DD}$**: The positive power supply voltage.\n*   **$R_D$**: The drain resistor (load resistor). It acts as a pull-up device.\n*   **$M_1$ and $M_2$**: Two N-channel MOSFETs (NMOS).\n    *   **$M_1$**: The bottom transistor. Its source is connected to ground.\n    *   **$M_2$**: The top transistor. Its source is connected to the drain of $M_1$.\n*   **$V_{in}$**: The input voltage signal.\n*   **$V_{out}$**: The output voltage signal, taken at the drain of $M_2$.\n\n### 3. Connectivity Analysis\n*   **Series Connection:** The transistors $M_1$ and $M_2$ are stacked in series. The current path flows from $V_{DD}$, through $R_D$, through the Drain-Source of $M_2$, through the Drain-Source of $M_1$, to Ground.\n*   **Gate Connection:** The gates of both $M_1$ and $M_2$ are connected together to the input node $V_{in}$. This is a crucial detail. It means both transistors receive the same gate drive voltage.\n\n### 4. Circuit Operation\n\nThis circuit functions primarily as an **Inverter (NOT gate)** in digital logic or an **inverting amplifier** in analog applications.\n\n*   **Case 1: Input Low ($V_{in} < V_{th}$)**\n    *   When the input voltage is below the threshold voltage ($V_{th}$) of the transistors, both $M_1$ and $M_2$ are in the **Cutoff region** (OFF).\n    *   No current flows through the resistor $R_D$ ($I_D \\approx 0$).\n    *   Therefore, there is no voltage drop across $R_D$.\n    *   **Output:** $V_{out} \\approx V_{DD}$ (Logic High).\n\n*   **Case 2: Input High ($V_{in} > V_{th}$)**\n    *   When the input voltage is high, both transistors turn **ON**.\n    *   Current flows from $V_{DD}$ through $R_D$ and the series combination of $M_2$ and $M_1$ to ground.\n    *   This creates a voltage drop across $R_D$, pulling $V_{out}$ down towards ground.\n    *   **Output:** $V_{out}$ becomes low (Logic Low), determined by the voltage divider formed by $R_D$ and the on-resistance of the stacked transistors ($R_{DS(on), M1} + R_{DS(on), M2}$).\n\n### 5. Analysis of the \"Stacked\" Configuration\nConnecting two transistors in series with their gates tied together creates a \"super-transistor\" effect. Here are the implications:\n\n*   **Effective Channel Length:** The two transistors behave like a single MOSFET with an effective channel length roughly equal to the sum of the individual lengths ($L_{eff} \\approx L_1 + L_2$).\n*   **Reduced Current Drive:** Because the effective channel length is longer, the drain current ($I_D$) for a given $V_{in}$ will be lower than if a single transistor were used. The top transistor $M_2$ has a source voltage higher than ground (let's call it $V_x$), so its gate-source voltage is $V_{GS2} = V_{in} - V_x$, which is less than $V_{GS1} = V_{in}$. This makes $M_2$ the \"bottleneck\" limiting the current.\n*   **Higher Output Resistance:** The stacked configuration increases the output resistance of the pull-down network. In analog terms, this can lead to higher gain if used as an amplifier, although the resistive load $R_D$ dominates here.\n*   **Stack Effect (Leakage Reduction):** In digital circuits, stacking transistors is a common technique to reduce subthreshold leakage current. Even if one transistor is weakly on, the voltage at the intermediate node rises, reducing the $V_{GS}$ of the other transistor, effectively turning it off harder.\n*   **Voltage Handling:** Stacking transistors allows the circuit to handle higher voltages. The voltage drop from $V_{out}$ to Ground is shared between $M_1$ and $M_2$, preventing breakdown in high-voltage applications.\n\n### Summary\nThe circuit is an **NMOS Inverter** where the switching element is a **stack of two NMOS transistors**.\n*   **Logic Function:** $V_{out} = \\text{NOT}(V_{in})$ (approximately).\n*   **Key Characteristic:** The series connection acts like a single transistor with a longer channel, resulting in lower current drive and higher resistance compared to a standard single-transistor inverter.",
        "format": "markdown",
        "sha256": "da184d4cfc4a9a65a1cf9f8a2d50be4ca887e43c58fc0c47ab187ac1399fa6b4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the common-gate series NMOS stack and states the essential result that its effective channel length is approximately L1 + L2. The inverter and secondary stack-effect discussion does not undermine that central conclusion.",
          "golden_solution_sha256": "f4c42a319616e7d942081a3389417d0f1c64822932dcec21eebd003d9f6660ad",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 5952,
        "total_tokens": 7083,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4765,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1131,
        "output_tokens": 5952,
        "total_tokens": 7083,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4765,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology, components, and operation.\n\n### 1. Circuit Identification\nThe circuit shown is a **MOSFET Differential Pair** (also known as a source-coupled pair). Specifically, it is configured as a **single-ended input, single-ended output amplifier**.\n\n### 2. Component Analysis\n*   **Transistors ($M_1$ and $M_2$):** These are NMOS transistors. We can deduce this because their sources are connected together to a current source ($I_1$) that goes to ground. For current to flow from the positive supply ($V_{DD}$) down to ground, the transistors must be N-channel devices (current flows from Drain to Source).\n*   **Current Source ($I_1$):** This is the \"tail current source.\" It provides a constant bias current $I_1$ to the common source node of the two transistors. This forces the sum of the drain currents to be constant: $I_{D1} + I_{D2} = I_1$.\n*   **Resistor ($R_D$):** This is the load resistor connected to the drain of $M_2$. It converts the drain current of $M_2$ into an output voltage.\n*   **Inputs:**\n    *   **$V_{in}$:** The signal input applied to the gate of $M_1$.\n    *   **$V_b$:** A DC bias voltage applied to the gate of $M_2$. This sets the operating point of the circuit.\n*   **Output ($V_{out}$):** The output voltage is taken at the drain of $M_2$.\n\n### 3. Circuit Operation\nThe circuit works by \"steering\" the tail current $I_1$ between the two branches ($M_1$ and $M_2$) based on the difference in gate voltages.\n\n*   **Current Steering:**\n    *   If **$V_{in} > V_b$**: Transistor $M_1$ turns on more strongly than $M_2$. Consequently, $M_1$ takes more of the tail current ($I_{D1}$ increases), and $M_2$ takes less ($I_{D2}$ decreases).\n    *   If **$V_{in} < V_b$**: Transistor $M_2$ turns on more strongly. $I_{D2}$ increases and $I_{D1}$ decreases.\n\n*   **Output Voltage Relationship:**\n    The output voltage is determined by the voltage drop across $R_D$:\n    $$V_{out} = V_{DD} - I_{D2} \\cdot R_D$$\n\n    *   When $V_{in}$ increases, $I_{D2}$ decreases. This reduces the voltage drop across $R_D$, causing **$V_{out}$ to increase** (move closer to $V_{DD}$).\n    *   Therefore, this configuration acts as a **non-inverting amplifier**.\n\n### 4. Small-Signal Analysis (Gain)\nThis circuit can be analyzed in two equivalent ways:\n\n**Method A: As a Differential Pair**\nFor a balanced differential pair with single-ended output, the small-signal voltage gain $A_v$ is half the gain of a common-source stage:\n$$A_v \\approx \\frac{g_m R_D}{2}$$\n*(where $g_m$ is the transconductance of the transistors, assuming $M_1$ and $M_2$ are matched).*\n\n**Method B: As a Cascade (Source Follower + Common Gate)**\n*   **Stage 1 ($M_1$):** Acts as a **Source Follower** (Common Drain). It buffers the input voltage $V_{in}$ to the common source node. The gain of this stage is approximately $1/2$ (because it is driving the low input impedance of the next stage, $1/g_m$).\n*   **Stage 2 ($M_2$):** Acts as a **Common Gate** amplifier. The signal at the source is amplified by the factor $g_m R_D$.\n*   **Total Gain:** $A_v \\approx (1/2) \\cdot (g_m R_D) = \\frac{g_m R_D}{2}$.\n\n### Summary\nThis is a fundamental building block in analog electronics, often found in the input stage of Operational Amplifiers (Op-Amps). It amplifies the difference between the input signal $V_{in}$ and the reference bias $V_b$ with a non-inverting gain of approximately $\\frac{g_m R_D}{2}$.",
        "format": "markdown",
        "sha256": "f37717adc7b428cd5c6759183cd837bbe6c8889bfd278b64231c10f2f05859f3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-coupled pair with M2 biased at Vb and output at its drain, and gives the correct non-inverting gain of approximately gmRD/2.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 7185,
        "total_tokens": 9019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6183,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 7185,
        "total_tokens": 9019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6183,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification and Components\nThe circuit is a MOSFET amplifier configuration consisting of:\n*   **Two NMOS Transistors ($M_1$ and $M_2$):** The arrows on the source terminals point outward (away from the channel), which is the standard symbol for NMOS transistors. They share a common source node.\n*   **Resistor ($R_D$):** A drain load resistor connected to $V_{DD}$.\n*   **Current Source ($I_1$):** A tail current source connected to ground, biasing the pair.\n*   **Terminals:**\n    *   $V_{in}$: Signal input at the gate of $M_1$.\n    *   $V_b$: DC bias voltage at the gate of $M_2$.\n    *   $V_{out}$: Output voltage at the drain of $M_2$.\n    *   $V_{DD}$: Positive power supply.\n\n### 2. Topology Analysis\nThis circuit can be viewed as a cascade of two amplifier stages or a specific configuration of a differential pair:\n*   **Stage 1 ($M_1$): Common-Drain (Source Follower).** The input is at the gate, the drain is connected to AC ground ($V_{DD}$), and the output is taken from the source. This stage provides a high input impedance and a voltage gain slightly less than unity.\n*   **Stage 2 ($M_2$): Common-Gate Amplifier.** The input is effectively at the source (driven by $M_1$), the gate is held at a fixed DC potential ($V_b$, which is AC ground), and the output is at the drain.\n\nTogether, this forms a **Common-Drain – Common-Gate (CD-CG)** cascade.\n\n### 3. DC Analysis (Biasing)\n*   The tail current source $I_1$ forces the sum of the drain currents of the two transistors to be constant (assuming saturation region operation):\n    $$I_{D1} + I_{D2} = I_1$$\n*   The output DC voltage is determined by the current through $M_2$:\n    $$V_{out} = V_{DD} - I_{D2} R_D$$\n*   For the circuit to work properly, both transistors must be in the saturation region. $V_b$ is chosen to set the appropriate DC operating point for $M_2$.\n\n### 4. AC Analysis (Small-Signal Operation)\nLet's trace the signal to determine the function and gain:\n1.  **Input Increase:** If the input voltage $V_{in}$ increases, the gate-source voltage of $M_1$ ($V_{GS1}$) tends to increase.\n2.  **Source Follower Action:** $M_1$ conducts more current, pulling the common source node voltage ($V_S$) up. The voltage at the source follows the input: $V_S \\approx V_{in} - V_{GS1(th)}$.\n3.  **Common-Gate Action:** The gate of $M_2$ is fixed at $V_b$. As the source voltage $V_S$ rises, the gate-source voltage of $M_2$ ($V_{GS2} = V_b - V_S$) **decreases**.\n4.  **Output Response:** A decrease in $V_{GS2}$ causes the drain current $I_{D2}$ to decrease. Consequently, the voltage drop across the resistor $R_D$ decreases ($V_{drop} = I_{D2}R_D$).\n5.  **Final Output:** Since $V_{out} = V_{DD} - I_{D2}R_D$, a decrease in current leads to an **increase** in $V_{out}$.\n\n**Conclusion:** The circuit acts as a **Non-Inverting Amplifier**.\n\n### 5. Voltage Gain Derivation\nUsing small-signal models (assuming ideal current source $I_1$ and ignoring output resistance $r_o$ for simplicity):\n\n*   **At the common source node ($V_S$):** The current from $M_1$ must equal the current into $M_2$ (since the tail current source has infinite AC impedance).\n    $$g_{m1}(V_{in} - V_S) = g_{m2}(V_S - 0)$$  *(Note: For $M_2$, $V_{gs} = 0 - V_S = -V_S$, but current direction considerations lead to this balance)*.\n    Actually, a more precise KCL at the source node (sum of currents leaving = 0):\n    $$-g_{m1}(V_{in} - V_S) - g_{m2}(0 - V_S) = 0$$\n    $$g_{m1}V_{in} = V_S(g_{m1} + g_{m2})$$\n    $$V_S = V_{in} \\frac{g_{m1}}{g_{m1} + g_{m2}}$$\n\n*   **At the output node ($V_{out}$):** The current through $R_D$ is driven by the drain current of $M_2$.\n    $$V_{out} = - (I_{d2}) R_D$$\n    The small signal drain current of $M_2$ (flowing from drain to source) is $i_{d2} = g_{m2}V_{gs2} = g_{m2}(0 - V_S) = -g_{m2}V_S$.\n    Wait, the current flows from $V_{DD}$ through $R_D$ into the drain. So $V_{out} = 0 - i_{d2\\_leaving} R_D$?\n    Let's use the standard formula for a Common-Gate stage gain with input $V_S$: $V_{out} = g_{m2} R_D V_S$ (Non-inverting relative to source input? No, CG is non-inverting from source to drain. If source goes up, $V_{gs}$ goes down, $I_d$ goes down, $V_{out}$ goes up. Yes, non-inverting).\n    $$V_{out} = g_{m2} R_D V_S$$\n\n*   **Total Gain ($A_v$):**\n    $$A_v = \\frac{V_{out}}{V_{in}} = \\left( \\frac{g_{m1}}{g_{m1} + g_{m2}} \\right) (g_{m2} R_D)$$\n    $$A_v = \\frac{g_{m1} g_{m2} R_D}{g_{m1} + g_{m2}}$$\n\nIf the transistors are identical ($g_{m1} = g_{m2} = g_m$), the gain simplifies to:\n$$A_v = \\frac{1}{2} g_m R_D$$\n\n### Summary\nThis circuit is a **non-inverting amplifier** with high input impedance (due to the MOSFET gate input). It combines the buffering capability of a source follower ($M_1$) with the gain and frequency response benefits of a common-gate stage ($M_2$). This topology is often used in high-frequency applications because it minimizes the Miller effect capacitance at the input.",
        "format": "markdown",
        "sha256": "ad9fdc86337bee1a1e8d023f2d89da032eda92c4c3310621caba32aead2a9d87"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as a source follower driving M2 in common-gate, and gives the correct non-inverting gain. Minor sign-convention hesitation in the derivation is resolved by the final result.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 11185,
        "total_tokens": 13019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9576,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 11185,
        "total_tokens": 13019,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9576,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-026-source-follower-drives-common-gate",
      "part": "part1",
      "question_number": 26,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-026-source-follower-drives-common-gate/figure-20.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the topology, components, and operation.\n\n### 1. Circuit Topology and Components\nThe circuit shown is a **MOSFET Differential Pair** (also known as a long-tailed pair) configured with a single-ended input and a single-ended output.\n\n*   **Transistors ($M_1, M_2$):** These are NMOS transistors. Their sources are tied together, which is the characteristic structure of a differential pair.\n    *   **$M_1$:** Acts as the input transistor. Its gate is connected to the input signal $V_{\\text{in}}$, and its drain is connected directly to the power supply $V_{DD}$.\n    *   **$M_2$:** Acts as the amplifying transistor (common-gate configuration relative to the signal at the source). Its gate is connected to a fixed bias voltage $V_b$, and its drain is connected to the output node.\n*   **Current Source ($I_1$):** This is an ideal current source connected to the common source node of the transistors and ground. It acts as a **tail current source**, setting the total bias current for the circuit ($I_{D1} + I_{D2} \\approx I_1$).\n*   **Resistor ($R_D$):** This is the drain load resistor for transistor $M_2$. It converts the drain current of $M_2$ into an output voltage.\n*   **Terminals:**\n    *   $V_{DD}$: Positive power supply rail.\n    *   $V_{\\text{in}}$: Input voltage signal.\n    *   $V_b$: Bias voltage (reference voltage).\n    *   $V_{\\text{out}}$: Output voltage.\n\n### 2. Circuit Operation\nThis circuit functions as a **differential amplifier**. It amplifies the difference between the input voltage $V_{\\text{in}}$ and the reference bias voltage $V_b$.\n\n**DC Analysis (Biasing):**\nThe tail current source $I_1$ forces the sum of the drain currents of the two transistors to be constant (ignoring channel length modulation):\n$$I_{D1} + I_{D2} = I_1$$\nThe distribution of this current between $M_1$ and $M_2$ depends on the difference between their gate voltages ($V_{\\text{in}}$ and $V_b$).\n\n**AC Analysis (Small Signal Operation):**\nThe circuit operates by \"steering\" the tail current $I_1$ between the two branches based on the input voltage.\n\n1.  **Input Increase ($V_{\\text{in}} \\uparrow$):**\n    *   When $V_{\\text{in}}$ increases relative to $V_b$, the gate-source voltage of $M_1$ ($V_{GS1}$) effectively increases.\n    *   This causes $M_1$ to conduct more current ($I_{D1}$ increases).\n    *   Since the total current $I_1$ is fixed, the current through $M_2$ must decrease ($I_{D2}$ decreases).\n    *   The output voltage is given by $V_{\\text{out}} = V_{DD} - I_{D2}R_D$.\n    *   As $I_{D2}$ decreases, the voltage drop across $R_D$ decreases, causing **$V_{\\text{out}}$ to increase**.\n\n2.  **Input Decrease ($V_{\\text{in}} \\downarrow$):**\n    *   When $V_{\\text{in}}$ decreases, $M_1$ conducts less current.\n    *   More current is steered to $M_2$ ($I_{D2}$ increases).\n    *   The voltage drop across $R_D$ increases, causing **$V_{\\text{out}}$ to decrease**.\n\n### 3. Function and Gain\n*   **Function:** The circuit acts as a **non-inverting amplifier**. The output signal is in phase with the input signal $V_{\\text{in}}$.\n*   **Gain:** Assuming the transistors are matched ($g_{m1} = g_{m2} = g_m$), the small-signal voltage gain $A_v$ is approximately:\n    $$A_v = \\frac{v_{\\text{out}}}{v_{\\text{in}}} \\approx \\frac{1}{2} g_m R_D$$\n    *(Note: The factor of $1/2$ arises because the input signal is split between the two transistors at the common source node. $M_1$ acts somewhat like a source follower driving the source of $M_2$, which acts as a common-gate amplifier.)*\n\n### Summary\nThis is a single-ended output differential amplifier stage. It takes an input signal $V_{\\text{in}}$, compares it against a reference $V_b$, and produces an amplified, non-inverted output voltage at $V_{\\text{out}}$.",
        "format": "markdown",
        "sha256": "3c41b86f3ad3fc31759a99dccd26800e3cad7c74c30e106186a6d6494e795205"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-coupled differential pair (equivalently, a source follower driving a common-gate stage), gives the right current-steering and non-inverting behavior, and states the matched-device gain of approximately gm RD/2.",
          "golden_solution_sha256": "5f76b34ca8287a0570c6f002e2eadb7a24e8054bf59e90b39e7d140a788b3c2c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 9974,
        "total_tokens": 11808,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8873,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1834,
        "output_tokens": 9974,
        "total_tokens": 11808,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8873,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To explain why the output impedance of this circuit can be inductive, we need to analyze the small-signal impedance looking into the output node $V_{\\text{out}}$.\n\nThe circuit consists of a source follower transistor $M_1$ with a series gate resistance $R_S$, and a current source load $M_2$. The output impedance $Z_{\\text{out}}$ is the parallel combination of the impedance looking down into the drain of $M_2$ (which is roughly $r_{o2}$, a large resistance) and the impedance looking up into the source of $M_1$.\n\nThe inductive behavior arises primarily from the impedance looking into the source of $M_1$.\n\n### 1. Small-Signal Model Analysis\nLet's determine the impedance looking into the source of $M_1$, denoted as $Z_s$. We apply a test voltage $V_x$ at the source (node $V_{\\text{out}}$) and measure the resulting current $I_x$ flowing into the source terminal.\n\n*   **Gate Circuit:** The gate of $M_1$ is connected to ground (since $V_{\\text{in}}$ is grounded for impedance calculation) through the resistor $R_S$. There is a parasitic gate-source capacitance $C_{gs}$.\n*   **Voltage at Gate ($V_g$):** The voltage $V_x$ at the source is coupled to the gate through $C_{gs}$. The gate voltage is determined by the voltage divider formed by $C_{gs}$ and $R_S$:\n    $$V_g = V_x \\frac{R_S}{R_S + \\frac{1}{sC_{gs}}} = V_x \\frac{s R_S C_{gs}}{1 + s R_S C_{gs}}$$\n*   **Gate-Source Voltage ($V_{gs}$):**\n    $$V_{gs} = V_g - V_x = V_x \\left( \\frac{s R_S C_{gs}}{1 + s R_S C_{gs}} - 1 \\right) = -V_x \\frac{1}{1 + s R_S C_{gs}}$$\n\n### 2. Calculating the Impedance\nThe current $I_x$ flowing into the source terminal consists of the current through the capacitor $C_{gs}$ minus the current from the dependent current source $g_m V_{gs}$ (which flows from drain to source, i.e., into the source node).\n\nUsing Kirchhoff's Current Law (KCL) at the source node:\n$$I_x = I_{C_{gs}} - I_{g_m}$$\n$$I_x = (V_x - V_g)sC_{gs} - g_m V_{gs}$$\n\nSubstituting the expressions for $V_g$ and $V_{gs}$:\n$$I_x = V_x \\left( \\frac{sC_{gs}}{1 + s R_S C_{gs}} \\right) - g_m \\left( \\frac{-V_x}{1 + s R_S C_{gs}} \\right)$$\n$$I_x = V_x \\frac{sC_{gs} + g_m}{1 + s R_S C_{gs}}$$\n\nThe impedance looking into the source is $Z_s = V_x / I_x$:\n$$Z_s = \\frac{1 + s R_S C_{gs}}{g_m + s C_{gs}}$$\n\n### 3. Identifying the Inductive Component\nTo see the inductive nature, we can rewrite this expression for frequencies where $s C_{gs} \\ll g_m$ (below the pole frequency):\n$$Z_s \\approx \\frac{1}{g_m} (1 + s R_S C_{gs}) \\left( 1 - s \\frac{C_{gs}}{g_m} \\right)$$\n$$Z_s \\approx \\frac{1}{g_m} \\left( 1 + s R_S C_{gs} - s \\frac{C_{gs}}{g_m} \\right)$$\n$$Z_s \\approx \\frac{1}{g_m} + s \\left[ \\frac{C_{gs}}{g_m} \\left( R_S - \\frac{1}{g_m} \\right) \\right]$$\n\nThis equation is in the form of a resistor in series with an inductor: $Z = R + sL$.\n*   **Resistance:** $R = 1/g_m$\n*   **Inductance:** $L = \\frac{C_{gs}}{g_m} (R_S - \\frac{1}{g_m})$\n\n### Conclusion\nThe output impedance behaves inductively if the equivalent inductance $L$ is positive. This occurs when:\n$$R_S > \\frac{1}{g_m}$$\n\n**Physical Intuition:**\nThe resistor $R_S$ and the capacitor $C_{gs}$ create a time delay (phase shift) in the feedback from the source to the gate. When the output voltage changes, the gate voltage cannot change instantaneously due to the $R_S C_{gs}$ time constant. This delay causes the transistor's current response to lag behind the voltage change in a way that mimics the behavior of an inductor (where voltage leads current).\n\nThis phenomenon is often called **\"source follower peaking\"** or inductive output impedance. It can cause instability or ringing when the circuit drives a capacitive load, as the inductive output impedance and the load capacitance form an LC resonant tank.",
        "format": "markdown",
        "sha256": "6f3909ee5bd5c82e34e1355dc67e6f6a883ed2e0172518be3460473e8b8a213e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source-follower topology, derives the correct output-impedance expression, and shows that its low-frequency expansion has positive inductance when R_S > 1/g_m. The explanation is consistent with the gate-source capacitance and includes appropriate assumptions.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8593,
        "total_tokens": 9928,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7411,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8593,
        "total_tokens": 9928,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7411,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a **source follower** (common-drain amplifier) formed by transistor $M_1$, loaded by a current source formed by transistor $M_2$. The output is taken at the source of $M_1$.\n\nThe output impedance of this circuit can exhibit **inductive behavior** due to the interaction between the gate resistance $R_S$ and the gate-source capacitance $C_{gs}$ of transistor $M_1$.\n\nHere is the step-by-step explanation:\n\n### 1. Small-Signal Analysis of the Source Follower\nTo find the output impedance, we look into the node $V_{out}$ (the source of $M_1$). We can model the impedance looking into the source of $M_1$, denoted as $Z_{source}$.\n\n*   **Low Frequencies:** At low frequencies (or DC), the capacitor $C_{gs}$ acts as an open circuit. The gate of $M_1$ is effectively connected to ground through $R_S$ (since $V_{in}$ is set to 0 for impedance calculation). The impedance looking into the source of a MOSFET with its gate grounded is approximately **$1/g_{m1}$** (where $g_{m1}$ is the transconductance). This is a small resistive value.\n\n*   **High Frequencies:** As frequency increases, the impedance of the capacitor $C_{gs}$ decreases. The capacitor begins to couple the changing voltage at the source ($V_{out}$) to the gate.\n    *   Ideally, if $C_{gs}$ were a perfect short, the gate voltage $V_g$ would follow the source voltage $V_{out}$ exactly.\n    *   If $V_g = V_{out}$, then the gate-source voltage $V_{gs} = V_g - V_{out} = 0$.\n    *   With $V_{gs} = 0$, the dependent current source $g_{m1}V_{gs}$ inside the transistor produces zero current. The transistor effectively \"turns off\" for small signals.\n    *   Consequently, the impedance looking into the source becomes very large (approaching the value of $R_S$ or the output resistance $r_o$).\n\n### 2. The Inductive Effect\nAn inductor is characterized by an impedance that **increases with frequency** ($Z_L = j\\omega L$).\n\nIn this circuit, the output impedance transitions from a low value ($\\approx 1/g_{m1}$) at low frequencies to a high value at high frequencies. This rising impedance profile mimics the behavior of an inductor.\n\nMathematically, the impedance looking into the source can be approximated as:\n$$Z_{out} \\approx \\frac{1}{g_{m1}} + s \\left( \\frac{R_S C_{gs}}{g_{m1}} \\right)$$\nThis equation represents a resistor ($1/g_{m1}$) in series with an inductor ($L_{eq} = \\frac{R_S C_{gs}}{g_{m1}}$).\n\n### Summary\nThe inductive behavior arises because the **gate resistance $R_S$** and **gate-source capacitance $C_{gs}$** create a time delay. When the output voltage $V_{out}$ changes rapidly, the gate voltage $V_g$ cannot follow immediately. This delay reduces the negative feedback effect of the source follower at higher frequencies, causing the effective output impedance to rise, which is characteristic of an inductor.\n\nThis effect is often significant in high-speed circuits and can cause peaking or instability (ringing) if the output drives a capacitive load, forming an LC tank circuit.",
        "format": "markdown",
        "sha256": "1ec251eec4148a89119ba0fac82b16c76dc35be8d63eea01faa454450096b61a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the source follower and explains the rise from about 1/gm at low frequency to about RS at high frequency as Cgs shorts gate to source, yielding inductive behavior. The equivalent-inductance formula is approximate and omits a term, but the golden solution’s full-credit rule applies.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8334,
        "total_tokens": 9669,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7544,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8334,
        "total_tokens": 9669,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7544,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-027-explain-why-output-impedance-be-inductive",
      "part": "part1",
      "question_number": 27,
      "question": "Explain why the output impedance of the circuit shown in the figure can be inductive.",
      "figures": [
        "tasks/part1-027-explain-why-output-impedance-be-inductive/figure-21.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a **Source Follower** (Common Drain amplifier) formed by transistor $M_1$, loaded by a current source $M_2$. The output is taken at the source of $M_1$.\n\nThe output impedance of this circuit can appear inductive due to the presence of the gate resistor $R_S$ and the parasitic capacitances of the transistor $M_1$ (specifically $C_{gs}$ and $C_{gd}$).\n\nHere is the step-by-step explanation:\n\n### 1. Small-Signal Analysis\nTo find the output impedance $Z_{out}$, we look into the node $V_{out}$ (the source of $M_1$). We can model the transistor $M_1$ with its transconductance $g_m$ and gate-source capacitance $C_{gs}$. We assume the input $V_{in}$ is grounded for impedance calculation.\n\nThe impedance looking into the source of a MOSFET is generally low, approximately $1/g_m$ at low frequencies. However, the resistor $R_S$ at the gate changes this behavior at higher frequencies.\n\n### 2. Derivation of Impedance\nLet's apply a test voltage $V_x$ at the output node $V_{out}$ and measure the current $I_x$ flowing into it.\n*   The gate voltage $V_g$ is determined by the voltage divider formed by the impedance of $C_{gs}$ and the resistor $R_S$ (ignoring $C_{gd}$ for simplicity). Since the input is grounded, $R_S$ connects the gate to ground.\n    $$V_g = V_x \\frac{R_S}{R_S + \\frac{1}{sC_{gs}}} = V_x \\frac{s C_{gs} R_S}{1 + s C_{gs} R_S}$$\n*   The gate-source voltage is $V_{gs} = V_g - V_x$.\n    $$V_{gs} = V_x \\left( \\frac{s C_{gs} R_S}{1 + s C_{gs} R_S} - 1 \\right) = V_x \\frac{-1}{1 + s C_{gs} R_S}$$\n*   The current $I_x$ entering the source node consists of the current through the capacitor $C_{gs}$ and the dependent current source $g_m V_{gs}$.\n    $$I_x = (V_x - V_g)sC_{gs} - g_m V_{gs}$$\n    Since $(V_x - V_g) = -V_{gs}$, we have:\n    $$I_x = -V_{gs}(sC_{gs} + g_m) = V_x \\frac{g_m + sC_{gs}}{1 + s C_{gs} R_S}$$\n\nThe output impedance $Z_{out} = V_x / I_x$ is:\n$$Z_{out} = \\frac{1 + s C_{gs} R_S}{g_m + s C_{gs}}$$\n\n### 3. Identifying the Inductive Term\nWe can rewrite this expression for frequencies where $s C_{gs} \\ll g_m$ (which is true for frequencies well below the transistor's cutoff frequency $\\omega_T$):\n\n$$Z_{out} \\approx \\frac{1}{g_m} (1 + s C_{gs} R_S) = \\frac{1}{g_m} + s \\left( \\frac{C_{gs} R_S}{g_m} \\right)$$\n\nThis equation has the form of a resistor in series with an inductor:\n$$Z = R_{eq} + s L_{eq}$$\nWhere:\n*   $R_{eq} = \\frac{1}{g_m}$\n*   $L_{eq} = \\frac{C_{gs} R_S}{g_m}$\n\n### 4. Physical Intuition\n*   **Low Frequencies:** The capacitor $C_{gs}$ is an open circuit. The gate is effectively at AC ground (through $R_S$). The circuit acts like a standard source follower with output impedance $\\approx 1/g_m$.\n*   **High Frequencies:** As frequency increases, the capacitor $C_{gs}$ starts to conduct. The changing voltage at the source ($V_{out}$) couples to the gate. Because of the resistor $R_S$, the gate voltage cannot change instantly; there is a delay (phase shift).\n*   **Inductive Behavior:** This delay means that the feedback mechanism (which normally keeps the output impedance low) becomes less effective at higher frequencies. The impedance magnitude starts to increase with frequency ($\\frac{d|Z|}{d\\omega} > 0$). An impedance that increases with frequency is the defining characteristic of an inductor ($Z_L = j\\omega L$).\n\n**Conclusion:**\nThe interaction between the gate resistance $R_S$ and the gate-source capacitance $C_{gs}$ creates a zero in the output impedance function. This causes the output impedance to rise with frequency in a specific range, behaving like an inductor with inductance $L \\approx \\frac{R_S C_{gs}}{g_m}$. This effect is often called \"source follower inductance\" and can cause peaking or ringing in the circuit's frequency response.",
        "format": "markdown",
        "sha256": "3abf9b7986d0a76a3f22fef07c07646b77514218e29960ef14c9a19a7e1e614a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies the source follower and derives the correct output-impedance expression. However, it omits the condition RS > 1/gm and the high-frequency limit Zout ≈ RS, and its inductance approximation omits the −Cgs/gm² contribution, so it overstates when the impedance is inductive.",
          "golden_solution_sha256": "8c59f914b88c1f25c100ef0914c7e54f6c3e86c55b273ac88a1c45724902d303",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8963,
        "total_tokens": 10298,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7828,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1335,
        "output_tokens": 8963,
        "total_tokens": 10298,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7828,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification and Topology\n*   **Components**: The circuit consists of two NMOS transistors ($M_1$ and $M_2$), a resistor ($R_{D1}$), a DC voltage supply ($V_{DD}$), and a current source ($I_{in}$).\n*   **Topology**: The circuit features a **cross-coupled** configuration.\n    *   The gate of $M_1$ is connected to the drain of $M_2$ (Node $X$).\n    *   The gate of $M_2$ is connected to the drain of $M_1$ (Node $V_{out}$).\n    *   This structure creates a feedback loop between the two stages.\n\n### 2. Feedback Analysis\nTo determine the nature of the circuit, we trace the signal path around the loop to check for positive or negative feedback.\n\n*   **Stage 1 ($M_1$):** This is a common-source amplifier with a resistive load $R_{D1}$.\n    *   If the voltage at node $X$ ($V_{GS1}$) **increases**, the current $I_{D1}$ increases.\n    *   Consequently, the voltage drop across $R_{D1}$ increases, causing $V_{out}$ to **decrease**.\n    *   **Gain:** Inverting ($A_1 < 0$).\n\n*   **Stage 2 ($M_2$):** This acts as a common-source stage where the input is at the gate ($V_{out}$) and the output is at the drain (Node $X$). The load is the current source $I_{in}$ (which has high impedance).\n    *   If $V_{out}$ ($V_{GS2}$) **increases**, the transistor $M_2$ turns on harder and draws more current ($I_{D2}$).\n    *   Since the current source $I_{in}$ provides a fixed current into node $X$, and $M_2$ pulls current from node $X$ to ground, an increase in $I_{D2}$ will pull the voltage at node $X$ **down**.\n    *   **Gain:** Inverting ($A_2 < 0$).\n\n*   **Loop Gain**: The total loop gain is the product of the two stages: $A_{loop} = A_1 \\times A_2 = (-) \\times (-) = (+)$.\n    *   Since the loop gain is positive, the circuit employs **positive feedback**.\n\n### 3. Circuit Function\nCircuits with positive feedback and high gain typically act as **bistable multivibrators (latches)** or **Schmitt triggers**. This circuit has two stable operating states and one unstable (metastable) state. It will \"latch\" into one of the two stable states depending on initial conditions or noise.\n\n### 4. Operating States\n\n**State 1: $V_{out}$ is High ($\\approx V_{DD}$)**\n*   **Condition**: $M_1$ is OFF, $M_2$ is ON.\n*   **Analysis**:\n    *   If $V_{out} \\approx V_{DD}$, the gate voltage of $M_2$ is high, turning $M_2$ ON strongly.\n    *   $M_2$ operates in the triode (linear) region to sink the current $I_{in}$ from node $X$. This keeps the voltage at node $X$ ($V_X$) very low.\n    *   Since $V_X$ (which is $V_{GS1}$) is low (below the threshold voltage $V_{TH1}$), $M_1$ is turned OFF.\n    *   With $M_1$ OFF, no current flows through $R_{D1}$, so $V_{out} = V_{DD} - 0 = V_{DD}$.\n    *   **This state is consistent and stable.**\n\n**State 2: $V_{out}$ is Low ($\\approx 0$ V)**\n*   **Condition**: $M_1$ is ON, $M_2$ is OFF.\n*   **Analysis**:\n    *   If $V_{out}$ is low (near ground), the gate voltage of $M_2$ is low, turning $M_2$ OFF ($I_{D2} \\approx 0$).\n    *   The current source $I_{in}$ pushes current into node $X$. With no path to ground through $M_2$, the voltage $V_X$ rises.\n    *   As $V_X$ rises above the threshold voltage $V_{TH1}$, $M_1$ turns ON strongly.\n    *   $M_1$ acts as a low resistance path to ground, pulling $V_{out}$ down towards 0 V.\n    *   **This state is consistent and stable.** (Note: In a real circuit, $V_X$ would rise until limited by leakage or breakdown, keeping $M_1$ fully on).\n\n**Metastable Point (Unstable Equilibrium)**\nThere is a theoretical DC operating point where both transistors are in saturation.\n*   From KCL at node $X$: $I_{D2} = I_{in}$. This sets $V_{out} = V_{TH2} + \\sqrt{\\frac{2I_{in}}{k'_2(W/L)_2}}$.\n*   From KCL at node $V_{out}$: $I_{D1} = \\frac{V_{DD} - V_{out}}{R_{D1}}$. This sets $V_X = V_{TH1} + \\sqrt{\\frac{2I_{D1}}{k'_1(W/L)_1}}$.\n*   Any small perturbation (noise) will drive the circuit away from this point towards one of the two stable states described above.\n\n### Summary\nThe circuit is a **bistable latch** (or Schmitt trigger) formed by cross-coupling two inverting stages.\n*   It converts the input current $I_{in}$ and circuit parameters into a digital output $V_{out}$ (either High or Low).\n*   A large $I_{in}$ tends to drive the circuit to State 2 ($V_{out}$ Low) by charging node $X$.\n*   A small $I_{in}$ allows the circuit to settle in State 1 ($V_{out}$ High).",
        "format": "markdown",
        "sha256": "304ef5238b50acc4084e8320ab9eb8a9d23da1904d43f05f1689f5ddc1cac074"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate connection to Vout, the positive-feedback loop through M1 and M2, and the resulting unstable/metastable operating point and latching behavior. The precise input-resistance formula is not required for full credit.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 11391,
        "total_tokens": 13077,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9969,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 11391,
        "total_tokens": 13077,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9969,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Component Identification\n*   **$V_{DD}$**: DC power supply voltage.\n*   **$R_{D1}$**: A drain resistor acting as a load.\n*   **$M_1$**: An NMOS transistor.\n*   **$M_2$**: An NMOS transistor.\n*   **$I_{in}$**: An ideal DC current source.\n*   **$V_{out}$**: The output voltage node.\n*   **$X$**: An internal node connecting the gate of $M_1$ and the drain of $M_2$.\n\n### 2. Circuit Topology Analysis\nThe circuit can be decomposed into two stages that are cross-coupled:\n\n*   **Stage 1 (Inverter 1):** Consists of transistor **$M_1$** and resistor **$R_{D1}$**.\n    *   **Input:** Node $X$ (Gate of $M_1$).\n    *   **Output:** Node $V_{out}$ (Drain of $M_1$).\n    *   **Operation:** This is a common-source amplifier with a resistive load, which functions as an inverter.\n        *   If voltage at $X$ is **High** ($> V_{th}$), $M_1$ turns ON, conducting current through $R_{D1}$, causing $V_{out}$ to drop (**Low**).\n        *   If voltage at $X$ is **Low**, $M_1$ turns OFF, and $V_{out}$ is pulled up to $V_{DD}$ through $R_{D1}$ (**High**).\n\n*   **Stage 2 (Inverter 2):** Consists of transistor **$M_2$** and current source **$I_{in}$**.\n    *   **Input:** Node $V_{out}$ (Gate of $M_2$).\n    *   **Output:** Node $X$ (Drain of $M_2$).\n    *   **Operation:** This is a common-source amplifier with an active current source load, which also functions as an inverter.\n        *   If voltage at $V_{out}$ is **High**, $M_2$ turns ON. It sinks current from node $X$ to ground. Since $I_{in}$ is a fixed current pushing into node $X$, if $M_2$ is strong enough, it pulls node $X$ **Low**.\n        *   If voltage at $V_{out}$ is **Low**, $M_2$ turns OFF. The current source $I_{in}$ pushes current into node $X$ with no path to ground (since the gate of $M_1$ is high impedance), causing the voltage at $X$ to rise (**High**).\n\n### 3. Feedback and Function\nThe output of Stage 1 ($V_{out}$) is connected to the input of Stage 2, and the output of Stage 2 ($X$) is connected to the input of Stage 1.\n*   Stage 1 is inverting ($X \\uparrow \\Rightarrow V_{out} \\downarrow$).\n*   Stage 2 is inverting ($V_{out} \\uparrow \\Rightarrow X \\downarrow$).\n\nTwo inversions in a loop create **positive feedback**. A circuit with two cross-coupled inverters forms a **Bistable Latch** (or a memory cell, similar to an SRAM cell).\n\n### 4. Stable States\nBecause of the positive feedback, the circuit has two stable operating points (states):\n\n*   **State A (Logic High at Output):**\n    *   $V_{out} \\approx V_{DD}$ (High).\n    *   This turns **$M_2$ ON**. $M_2$ pulls node $X$ down to a low voltage (determined by $I_{in}$ and the on-resistance of $M_2$).\n    *   Since $X$ is Low, **$M_1$ is OFF**.\n    *   With $M_1$ OFF, no current flows through $R_{D1}$, so $V_{out}$ stays at $V_{DD}$. This state is self-sustaining.\n\n*   **State B (Logic Low at Output):**\n    *   $V_{out} \\approx 0$ V (Low).\n    *   This turns **$M_2$ OFF**.\n    *   With $M_2$ OFF, the current source $I_{in}$ charges node $X$ up towards $V_{DD}$ (High).\n    *   Since $X$ is High, **$M_1$ turns ON** strongly.\n    *   $M_1$ pulls $V_{out}$ down to near ground. This state is also self-sustaining.\n\n### Conclusion\nThe circuit is a **bistable latch** (memory element). It will settle into one of two stable states depending on initial conditions (power-up state) or noise. It stores 1 bit of information.\n*   If $V_{out}$ is high, it represents a stored '1'.\n*   If $V_{out}$ is low, it represents a stored '0'.",
        "format": "markdown",
        "sha256": "420edb4f020b4e3630c5ca693e6ea668923b1ac99f35354575094860c1f91726"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate connection to Vout, the positive-feedback loop through M1 and M2, and the resulting latching/bistable behavior. These satisfy the golden solution’s full-credit rule.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 12299,
        "total_tokens": 13985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11147,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 12299,
        "total_tokens": 13985,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11147,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-028-current-input-positive-feedback",
      "part": "part1",
      "question_number": 28,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-028-current-input-positive-feedback/figure-22.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of its topology, operation, and function.\n\n### 1. Circuit Components and Topology\nThe circuit consists of the following components:\n*   **$M_1$ and $M_2$**: Two NMOS transistors.\n*   **$R_{D1}$**: A load resistor connected to the supply voltage $V_{DD}$.\n*   **$I_{in}$**: An input DC current source.\n*   **$V_{DD}$**: The positive power supply.\n\n**Connections:**\n*   **Stage 1 ($M_1$):** Transistor $M_1$ is configured as a **Common-Source amplifier**. Its gate is connected to node **X**, its source is grounded, and its drain is connected to the output node **$V_{out}$** (via resistor $R_{D1}$). This stage acts as an inverter: a high voltage at X turns $M_1$ on, pulling $V_{out}$ low.\n*   **Stage 2 ($M_2$):** Transistor $M_2$ is also configured as a Common-Source stage. Its gate is connected to **$V_{out}$**, its source is grounded, and its drain is connected to node **X**. The current source $I_{in}$ is connected to node X, acting as an active load or input driver. This stage also acts as an inverter: a high voltage at $V_{out}$ turns $M_2$ on, pulling node X low.\n\n### 2. Feedback Analysis\nThe circuit forms a closed loop:\n1.  The output **$V_{out}$** is fed to the gate of **$M_2$**.\n2.  The drain of **$M_2$** (node **X**) is fed to the gate of **$M_1$**.\n3.  The drain of **$M_1$** is the output **$V_{out}$**.\n\nSince both stages ($M_1$ and $M_2$) are common-source amplifiers, each provides a $180^{\\circ}$ phase shift (inversion).\n*   Inversion 1: $V_{out} \\rightarrow$ Node X (via $M_2$)\n*   Inversion 2: Node X $\\rightarrow V_{out}$ (via $M_1$)\n\nTwo inversions in a loop result in **Positive Feedback** ($180^{\\circ} + 180^{\\circ} = 360^{\\circ}$).\n\n### 3. Circuit Function: Bistable Latch / Schmitt Trigger\nDue to the positive feedback, this circuit acts as a **bistable latch** or a **Schmitt trigger** (a comparator with hysteresis). It has two stable states and will regenerate any small difference to one of the rails.\n\nThe state of the circuit depends on the magnitude of the input current **$I_{in}$**.\n\n**State 1: Low $I_{in}$ (Output High)**\n*   If $I_{in}$ is small, the voltage at node **X** is low.\n*   Since $V_X$ (Gate of $M_1$) is low, **$M_1$ is OFF**.\n*   With $M_1$ off, no current flows through $R_{D1}$, so **$V_{out} \\approx V_{DD}$** (High).\n*   Since $V_{out}$ is High, the Gate of $M_2$ is High, turning **$M_2$ ON**.\n*   $M_2$ conducts the current $I_{in}$ to ground. This is a consistent, stable state.\n\n**State 2: High $I_{in}$ (Output Low)**\n*   If $I_{in}$ is large, it forces the voltage at node **X** to rise (since it pushes current into the high-impedance gate of $M_1$ and the drain of $M_2$).\n*   As $V_X$ rises, **$M_1$ turns ON**.\n*   $M_1$ draws current through $R_{D1}$, causing **$V_{out}$ to drop**.\n*   As $V_{out}$ drops, the Gate voltage of $M_2$ decreases, turning **$M_2$ OFF**.\n*   With $M_2$ off, it can no longer sink the current $I_{in}$, causing $V_X$ to rise even further. This positive feedback loop drives $M_1$ fully ON and $M_2$ fully OFF.\n*   Result: **$V_{out} \\approx 0$** (Low) and **$V_X$ is High**.\n\n### Summary\nThis circuit is a **current-controlled latch** or **regenerative comparator**.\n*   It converts the analog input current $I_{in}$ into a digital output voltage $V_{out}$.\n*   The positive feedback provides **hysteresis**, making the switching sharp and noise-immune.\n*   **Low $I_{in}$** $\\rightarrow$ $V_{out} = V_{DD}$ (Logic High).\n*   **High $I_{in}$** $\\rightarrow$ $V_{out} \\approx 0$ (Logic Low).",
        "format": "markdown",
        "sha256": "618662586943f377f1db5e6952121ee23b3009012afee3ad65e8c2e9451ada64"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M2’s gate as connected to Vout, describes the positive-feedback loop, and recognizes the resulting bistable/latching behavior, satisfying the golden solution’s full-credit rule.",
          "golden_solution_sha256": "966942e01d767dcc8afc948021623863d816cf7567c0ad0be0b855267f6da7e8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 12392,
        "total_tokens": 14078,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11225,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1686,
        "output_tokens": 12392,
        "total_tokens": 14078,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11225,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification\nThis circuit is a **Transimpedance Amplifier (TIA)**. Its primary function is to convert an input current signal ($I_{\\text{in}}$) into an output voltage signal ($V_{\\text{out}}$). This topology is commonly used in optical communication receivers (to amplify current from a photodiode) and various sensor interfaces.\n\n### 2. Component Breakdown\n*   **Input:** An ideal current source $I_{\\text{in}}$.\n*   **Amplifier Core:** A two-stage amplifier consisting of two NMOS transistors, $M_1$ and $M_2$.\n    *   **$M_1$ (Common-Gate Stage):** The gate is connected to a fixed bias voltage $V_b$. The input signal is applied to the source, and the output is taken from the drain (node $X$).\n    *   **$M_2$ (Common-Source Stage):** The gate is connected to node $X$ (the output of the first stage). The source is grounded, and the output is taken from the drain.\n*   **Load Resistors:** $R_{D1}$ and $R_{D2}$ act as the load resistors for the respective transistor stages, converting drain currents into voltages.\n*   **Feedback Network:** The resistor $R_F$ connects the output node ($V_{\\text{out}}$) back to the input node (source of $M_1$).\n\n### 3. Signal Path and Polarity Analysis\nTo understand the operation, let's trace the signal polarity:\n1.  **Input Increase:** Suppose the input current $I_{\\text{in}}$ increases. This causes the voltage at the source of $M_1$ to rise.\n2.  **Stage 1 ($M_1$):** Since the gate voltage $V_b$ is fixed, an increase in source voltage decreases the gate-source voltage ($V_{GS1}$). This reduces the drain current of $M_1$. Consequently, the voltage drop across $R_{D1}$ decreases, causing the voltage at node $X$ to **rise**.\n3.  **Stage 2 ($M_2$):** The rise in voltage at node $X$ (which is the gate of $M_2$) increases $V_{GS2}$. This increases the drain current of $M_2$. Consequently, the voltage drop across $R_{D2}$ increases, causing the output voltage $V_{\\text{out}}$ to **fall**.\n\n**Conclusion:** The amplifier chain is **inverting** (an increase in input leads to a decrease in output).\n\n### 4. Feedback Analysis\n*   **Topology:** The circuit uses **Shunt-Shunt Feedback** (also known as Voltage-Current feedback).\n    *   **Shunt at Output:** The feedback resistor samples the output voltage ($V_{\\text{out}}$).\n    *   **Shunt at Input:** The feedback current is mixed with the input current at the input node.\n*   **Negative Feedback:** Since the amplifier is inverting, when $V_{\\text{out}}$ drops (due to an increase in input), the potential difference across $R_F$ changes such that current is drawn away from the input node (or less current is supplied to it), opposing the initial voltage rise. This confirms it is negative feedback.\n\n### 5. Circuit Characteristics\n*   **Transimpedance Gain:** For a high-gain amplifier with shunt-shunt feedback, the closed-loop gain is determined primarily by the feedback resistor.\n    $$V_{\\text{out}} \\approx -I_{\\text{in}} \\cdot R_F$$\n    The negative sign indicates the 180-degree phase shift (inversion) derived in step 3.\n*   **Input Impedance:** Shunt feedback at the input significantly reduces the input impedance. The input impedance of a common-gate stage is already low ($\\approx 1/g_m$), and the feedback reduces it further by a factor of $(1 + \\text{Loop Gain})$. This is ideal for a current input, as it prevents the input voltage from swinging wildly.\n*   **Output Impedance:** Shunt sampling at the output reduces the output impedance, making $V_{\\text{out}}$ a stiff voltage source.\n\n### Summary\nThe circuit is a high-gain, inverting Transimpedance Amplifier. It uses a Common-Gate ($M_1$) followed by a Common-Source ($M_2$) amplifier to provide gain, with a feedback resistor $R_F$ setting the conversion ratio from current to voltage ($V_{\\text{out}}/I_{\\text{in}} \\approx -R_F$).",
        "format": "markdown",
        "sha256": "cf5d2ae2daab77b27e8c99825d977e596054859de6980c347a19dc8effab79c9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as feedback from Vout to the input node. The negative-feedback polarity, approximate −RF transimpedance, and low input resistance are also correctly described.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 5420,
        "total_tokens": 7327,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4378,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 5420,
        "total_tokens": 7327,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4378,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis:\n\n### 1. Circuit Identification\nThis circuit is a **Transresistance Amplifier** (also known as a current-to-voltage converter). It takes an input current ($I_{\\text{in}}$) and produces an output voltage ($V_{\\text{out}}$). The circuit utilizes **shunt-shunt feedback** (voltage sampling, current mixing) through the resistor $R_F$.\n\n### 2. Component Breakdown & Topology\nThe circuit consists of a two-stage amplifier core with a feedback network:\n\n*   **Stage 1 ($M_1$): Common-Gate Amplifier**\n    *   Transistor $M_1$ is an NMOS transistor.\n    *   Its gate is connected to a fixed bias voltage $V_b$ (AC ground).\n    *   The input signal (current) is applied to its source terminal.\n    *   The output of this stage is taken at the drain (node $X$).\n    *   $R_{D1}$ acts as the load resistor for this stage.\n\n*   **Stage 2 ($M_2$): Common-Source Amplifier**\n    *   Transistor $M_2$ is an NMOS transistor.\n    *   Its gate is connected to node $X$ (the output of the first stage).\n    *   Its source is connected to ground.\n    *   The final output $V_{\\text{out}}$ is taken at the drain.\n    *   $R_{D2}$ acts as the load resistor for this stage.\n\n*   **Feedback Network ($R_F$)**\n    *   The resistor $R_F$ connects the output node ($V_{\\text{out}}$) back to the input node (source of $M_1$).\n    *   This creates a negative feedback loop. Specifically, it is **shunt-shunt feedback**, which lowers both the input and output impedances of the amplifier.\n\n### 3. Signal Analysis and Gain\nLet's trace the signal to understand the operation and derive the gain:\n\n1.  **Open-Loop Gain:**\n    *   **$M_1$ (Common-Gate):** A voltage increase at the source of $M_1$ decreases $V_{GS1}$, reducing the drain current $I_{D1}$. This causes the voltage at node $X$ ($V_X = V_{DD} - I_{D1}R_{D1}$) to **increase**. So, the gain from the source of $M_1$ to node $X$ is positive (non-inverting), approximately $A_{v1} \\approx g_{m1}R_{D1}$.\n    *   **$M_2$ (Common-Source):** An increase in voltage at node $X$ (gate of $M_2$) increases $V_{GS2}$, increasing drain current $I_{D2}$. This causes the output voltage ($V_{\\text{out}} = V_{DD} - I_{D2}R_{D2}$) to **decrease**. So, the gain from node $X$ to $V_{\\text{out}}$ is negative (inverting), approximately $A_{v2} \\approx -g_{m2}R_{D2}$.\n    *   **Total Open-Loop Voltage Gain ($A_v$):** The cascade of a non-inverting stage and an inverting stage results in a large negative gain from the input node (source of $M_1$) to $V_{\\text{out}}$.\n    $$A_v \\approx -(g_{m1}R_{D1})(g_{m2}R_{D2})$$\n\n2.  **Feedback Action:**\n    *   Assume the input current $I_{\\text{in}}$ increases. This tends to raise the voltage at the source of $M_1$.\n    *   Due to the high inverting gain of the amplifier chain, $V_{\\text{out}}$ will drop significantly.\n    *   The feedback resistor $R_F$ is connected between $V_{\\text{out}}$ and the input node. As $V_{\\text{out}}$ drops, current flows from the input node towards $V_{\\text{out}}$ through $R_F$ (opposing the current $i_{RF}$ direction shown if $V_{out} < V_{in}$, or simply drawing current away from the input node).\n    *   This action counteracts the initial voltage rise at the input node, confirming **negative feedback**.\n\n3.  **Closed-Loop Gain (Transresistance):**\n    *   In a shunt-shunt feedback configuration with high loop gain, the input node acts as a **virtual ground**. The voltage at the source of $M_1$ stays relatively constant.\n    *   Consequently, almost all the input current $I_{\\text{in}}$ is forced to flow through the feedback resistor $R_F$.\n    *   The current flows from the input node to $V_{\\text{out}}$ (since $V_{\\text{out}}$ will be negative relative to the virtual ground for a positive $I_{\\text{in}}$).\n    *   Using Ohm's law across $R_F$:\n        $$V_{\\text{out}} - V_{\\text{in\\_node}} \\approx -I_{\\text{in}} R_F$$\n    *   Since $V_{\\text{in\\_node}} \\approx 0$ (virtual ground):\n        $$V_{\\text{out}} \\approx -I_{\\text{in}} R_F$$\n\n### 4. Summary\n*   **Function:** Current-to-Voltage Converter (Transresistance Amplifier).\n*   **Gain:** The transresistance gain is approximately **$-R_F$** (Volts/Ampere). The negative sign indicates that a positive input current results in a negative output voltage.\n*   **Impedance:** The shunt-shunt feedback topology results in **low input impedance** and **low output impedance**, making it ideal for interfacing with current sources and driving voltage loads.",
        "format": "markdown",
        "sha256": "0c9f02aed4d751dedcda44019b45ca609b9157dc423d4e25f97197358366cfad"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as negative feedback from Vout to the input node, forming a transimpedance amplifier. The stated −RF gain and low input impedance are consistent with the solution.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 10621,
        "total_tokens": 12528,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9278,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 10621,
        "total_tokens": 12528,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9278,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-029-feedback-transimpedance-amplifier",
      "part": "part1",
      "question_number": 29,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-029-feedback-transimpedance-amplifier/figure-23.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is a detailed analysis of the topology, operation, and function of the circuit.\n\n### 1. Circuit Overview\nThis circuit is a **two-stage MOSFET amplifier with negative feedback**. Specifically, it is configured as a **Transresistance Amplifier** (also known as a Transimpedance Amplifier or TIA), which converts an input current ($I_{in}$) into an output voltage ($V_{out}$).\n\n### 2. Stage-by-Stage Analysis\n\nThe circuit consists of two amplification stages cascaded together:\n\n*   **Stage 1: Common-Gate Amplifier ($M_1$)**\n    *   **Configuration:** Transistor $M_1$ has its gate connected to a fixed bias voltage $V_b$ (AC ground). The input signal (current $I_{in}$) is applied to the source terminal, and the output is taken from the drain (node $X$). This is a Common-Gate (CG) configuration.\n    *   **Function:** A Common-Gate stage provides a **non-inverting** voltage gain from source to drain. If the voltage at the source increases, $V_{GS}$ decreases, reducing the drain current. This reduces the voltage drop across $R_{D1}$, causing the voltage at node $X$ ($V_X$) to increase.\n    *   **Gain:** The voltage gain from the source of $M_1$ to node $X$ is approximately $A_{v1} \\approx g_{m1} R_{D1}$.\n\n*   **Stage 2: Common-Source Amplifier ($M_2$)**\n    *   **Configuration:** Transistor $M_2$ has its source grounded, its gate connected to node $X$ (the output of the first stage), and its drain connected to the output node $V_{out}$. This is a Common-Source (CS) configuration.\n    *   **Function:** A Common-Source stage provides an **inverting** voltage gain. If the voltage at node $X$ increases, $V_{GS2}$ increases, increasing the drain current. This increases the voltage drop across $R_{D2}$, causing $V_{out}$ to decrease.\n    *   **Gain:** The voltage gain from node $X$ to $V_{out}$ is approximately $A_{v2} \\approx -g_{m2} (R_{D2} || R_F)$.\n\n### 3. Feedback Analysis\n\n*   **Feedback Element:** The resistor $R_F$ connects the output node ($V_{out}$) back to the input node (source of $M_1$).\n*   **Polarity:** The first stage is non-inverting and the second stage is inverting. Therefore, the total open-loop gain from the input node to $V_{out}$ is **negative** (inverting).\n*   **Feedback Type:** Since the feedback signal is connected in parallel (shunt) with the input and samples the output voltage in parallel (shunt), this is a **Shunt-Shunt Feedback** topology.\n*   **Negative Feedback:** Because the amplifier is inverting, feeding the output back to the input creates negative feedback. For example, if $I_{in}$ increases, it tends to raise the input voltage. This leads to a drop in $V_{out}$. The drop in $V_{out}$ draws current away from the input node through $R_F$ (since $i_{RF}$ flows from right to left in the diagram, a lower $V_{out}$ reduces this current or reverses it), counteracting the initial increase.\n\n### 4. Circuit Function and Gain\n\nThis circuit acts as a **Current-to-Voltage Converter**.\n\n*   **Virtual Ground:** Due to the high loop gain of the amplifier and the negative feedback, the input node (source of $M_1$) is held at a relatively constant AC voltage (a \"virtual ground\"). The gate is fixed at $V_b$, so the feedback works to keep the source voltage close to a DC bias point determined by $V_b$ and the threshold voltage.\n*   **Transresistance Gain:** Because the input node is a virtual ground, almost all the input current $I_{in}$ is forced to flow through the feedback resistor $R_F$.\n    *   Current equation at input node: $I_{in} \\approx \\frac{0 - V_{out}}{R_F}$ (assuming input voltage is approx 0 AC).\n    *   Therefore, **$V_{out} \\approx -I_{in} R_F$**.\n\nThe transresistance gain ($R_m = V_{out} / I_{in}$) is approximately **$-R_F$**.\n\n### 5. Impedance Characteristics\n*   **Input Impedance:** The shunt feedback at the input significantly **lowers the input impedance**. This is desirable for a current amplifier (TIA) as it allows the input current source to drive the circuit easily. The input impedance is roughly $R_{in} \\approx \\frac{1}{g_{m1}} || \\frac{R_F}{1 + |A_{loop}|}$.\n*   **Output Impedance:** The shunt feedback at the output (voltage sampling) significantly **lowers the output impedance**, making it a better voltage source. The output impedance is roughly $R_{out} \\approx \\frac{R_{D2}}{1 + |A_{loop}|}$.",
        "format": "markdown",
        "sha256": "04ca15bdc1f00ed03e8e9df3454afd85f3f1e89c62dcf8bc9c55c728c124ce1c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate input device, M2 as the common-source stage driven by X, and RF as feedback from Vout to the input node, forming a negative-feedback transimpedance amplifier. The stated high-loop-gain result of approximately −RF is also correct.",
          "golden_solution_sha256": "3de185b163e9067ba58585d0a347eecc50f9da3dc36d0d1a8e05a54adcc11752",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 7984,
        "total_tokens": 9891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6808,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1907,
        "output_tokens": 7984,
        "total_tokens": 9891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6808,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the components, topology, and function.\n\n### 1. Component Identification\n*   **Transistors**:\n    *   **$M_1$**: An **NMOS** transistor. The arrow on the source terminal points outward.\n        *   **Source**: Connected to the common input node (bottom center).\n        *   **Gate**: Connected to the bias voltage $V_b$.\n        *   **Drain**: Connected to the output node $V_{\\text{out}}$.\n    *   **$M_2$**: A **PMOS** transistor. The arrow on the source terminal points inward (towards the channel).\n        *   **Source**: Connected to the supply rail $V_{DD}$.\n        *   **Gate**: Connected to the common input node (bottom center).\n        *   **Drain**: Connected to the output node $V_{\\text{out}}$.\n*   **Current Sources**:\n    *   **$I_{\\text{in}}$**: An input current source pushing current upwards into the input node.\n    *   **Unlabeled Sink**: A current source (circle with downward arrow) pulling current from the input node to ground. Let's call this $I_{\\text{tail}}$.\n    *   **$I_1$**: A current source pulling current from $V_{DD}$ down to the output node $V_{\\text{out}}$.\n\n### 2. Circuit Topology\nThe circuit can be described as a **Transimpedance Amplifier** (Current-to-Voltage Converter) with a specific feedback structure, often resembling a regulated cascode or a shunt-feedback stage.\n\n*   **Input Node ($V_x$)**: The node connecting the sources/gates of the transistors and the input currents.\n    *   $V_x$ is the voltage at the junction of $I_{\\text{in}}$, the tail current sink, the Gate of $M_2$, and the Source of $M_1$.\n*   **Output Node ($V_{\\text{out}}$)**: The node connecting the drains of the transistors and the load current source $I_1$.\n\n### 3. Circuit Operation Analysis\n\n**DC Bias and KCL Equations:**\nLet $V_x$ be the voltage at the input node and $V_{\\text{out}}$ be the output voltage.\n\n*   **At the Input Node ($V_x$)**:\n    The current $I_{\\text{in}}$ enters the node, the tail current $I_{\\text{tail}}$ leaves, and the current through $M_1$ ($I_{D1}$) flows from Drain to Source (entering the node).\n    $$I_{\\text{in}} + I_{D1} = I_{\\text{tail}} \\quad \\Rightarrow \\quad I_{D1} = I_{\\text{tail}} - I_{\\text{in}}$$\n    *(Note: This assumes $M_1$ is conducting current from $V_{\\text{out}}$ to $V_x$.)*\n\n*   **At the Output Node ($V_{\\text{out}}$)**:\n    The current $I_1$ enters from the top, the current through $M_2$ ($I_{D2}$) enters from the top (since it's a PMOS with source at $V_{DD}$), and the current $I_{D1}$ leaves through $M_1$.\n    $$I_1 + I_{D2} = I_{D1}$$\n\n**Qualitative Behavior:**\n1.  **Input Effect**: If the input current $I_{\\text{in}}$ increases:\n    *   The voltage $V_x$ at the input node tends to rise.\n2.  **Transistor Response**:\n    *   **$M_2$ (PMOS)**: The source is at $V_{DD}$ and gate is at $V_x$. As $V_x$ rises, the source-gate voltage $V_{SG} = V_{DD} - V_x$ decreases. This causes $M_2$ to turn off slightly, reducing $I_{D2}$.\n    *   **$M_1$ (NMOS)**: The gate is at fixed bias $V_b$ and source is at $V_x$. As $V_x$ rises, the gate-source voltage $V_{GS} = V_b - V_x$ decreases. This causes $M_1$ to turn off slightly, reducing its current capability $I_{D1}$.\n3.  **Output Voltage ($V_{\\text{out}}$)**:\n    *   From the KCL equation $I_1 + I_{D2} = I_{D1}$, we can see that the circuit balances the currents.\n    *   Since $I_{D1}$ is largely determined by $V_{GS1}$ (which depends on $V_x$), and $V_x$ is determined by the input current balance, the circuit converts the input current $I_{\\text{in}}$ into a specific operating point for the transistors.\n    *   $V_{\\text{out}}$ will adjust to satisfy the current requirements of $M_1$ (specifically maintaining saturation if designed as an amplifier).\n\n### 4. Summary\nThis circuit acts as a **current-controlled voltage source** or a specific stage in an analog IC (like a bias circuit or amplifier input stage).\n*   **$M_1$** acts as a **Common-Gate** amplifier stage (input at source, output at drain) with a fixed gate bias.\n*   **$M_2$** acts as an **active load** or feedback element (Common-Source configuration driven by the input node voltage).\n*   The combination creates a feedback loop where the input current modulates the gate of the PMOS load ($M_2$) and the source of the NMOS driver ($M_1$), stabilizing the output voltage $V_{\\text{out}}$ based on the input current $I_{\\text{in}}$.",
        "format": "markdown",
        "sha256": "32b0d3aa89be2dd338892b74856ab0c802d290c3373f4599f5d2e96a7b2a7cfe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misreads M2’s connections: its gate is driven by Vout and its drain feeds the input node, not the other way around. This misses the central feedback loop and the circuit’s low input resistance/current-buffer behavior.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 18891,
        "total_tokens": 20667,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17554,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 18891,
        "total_tokens": 20667,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 17554,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of the topology and its operation.\n\n### 1. Component Identification\n*   **Transistors:**\n    *   **$M_1$**: An **NMOS** transistor. The arrow on the source terminal points outward (away from the channel).\n    *   **$M_2$**: A **PMOS** transistor. The arrow on the source terminal points inward (towards the channel).\n*   **Sources:**\n    *   **$I_{\\text{in}}$**: An input current source pushing current upwards from ground.\n    *   **Downward Current Source (unlabeled, let's call it $I_{\\text{bias}}$)**: A bias current source pulling current downwards to ground.\n    *   **$I_1$**: A constant current source pulling current from $V_{DD}$ to the output node $V_{\\text{out}}$.\n*   **Terminals:**\n    *   **$V_{DD}$**: Positive supply voltage.\n    *   **$V_b$**: A constant bias voltage applied to the gate of $M_1$.\n    *   **$V_{\\text{out}}$**: The output voltage node.\n\n### 2. Circuit Topology\nThe circuit can be broken down into two main stages sharing a common input node (let's call the node connecting the current sources, the gate of $M_2$, and the source of $M_1$ as **Node X**).\n\n*   **Input Stage (Node X):**\n    *   The net current entering Node X is $I_{\\text{net}} = I_{\\text{in}} - I_{\\text{bias}}$.\n    *   Since the gate of $M_2$ draws negligible current, this net current must flow into the source of transistor $M_1$.\n    *   Therefore, the drain current of $M_1$ is set by the input: $I_{D1} \\approx I_{\\text{in}} - I_{\\text{bias}}$.\n\n*   **Transistor $M_1$ (Common-Gate Configuration):**\n    *   $M_1$ has its gate fixed at $V_b$ and its source at Node X.\n    *   It acts as a **common-gate amplifier** or a current buffer. It passes the current from the input node to the output node ($V_{\\text{out}}$).\n    *   The voltage at Node X ($V_X$) is determined by the current $I_{D1}$ and the bias $V_b$:\n        $$V_X = V_b - V_{GS1} = V_b - \\left( V_{th,n} + \\sqrt{\\frac{2 I_{D1}}{\\mu_n C_{ox} (W/L)_1}} \\right)$$\n    *   As $I_{\\text{in}}$ increases, $I_{D1}$ increases, which requires a larger $V_{GS1}$, causing $V_X$ to decrease.\n\n*   **Transistor $M_2$ (Common-Source Configuration):**\n    *   $M_2$ is a PMOS transistor with its source connected to $V_{DD}$ and its gate connected to Node X.\n    *   It acts as a **common-source amplifier** driven by the voltage at Node X.\n    *   The source-gate voltage is $V_{SG2} = V_{DD} - V_X$.\n    *   As $I_{\\text{in}}$ increases $\\rightarrow$ $V_X$ decreases $\\rightarrow$ $V_{SG2}$ increases $\\rightarrow$ $M_2$ turns on harder, increasing its drain current $I_{D2}$.\n\n*   **Output Node ($V_{\\text{out}}$):**\n    *   The drains of $M_1$ and $M_2$ are connected together at $V_{\\text{out}}$.\n    *   Current $I_1$ flows into this node from $V_{DD}$.\n    *   Current $I_{D2}$ (from PMOS $M_2$) flows into this node.\n    *   Current $I_{D1}$ (into NMOS $M_1$) flows out of this node.\n    *   The node $V_{\\text{out}}$ is a high-impedance node (sum of output resistances $r_{o1} || r_{o2}$).\n\n### 3. Circuit Function\nThis circuit functions as a **Transimpedance Amplifier** (Current-to-Voltage Converter) with high gain.\n\n*   **Operation:** An input current $I_{\\text{in}}$ creates a voltage change at Node X. This voltage change modulates the current $I_{D2}$ through $M_2$.\n*   **Current Summation:** At the output node, the currents sum up. The net current charging the output capacitance (or flowing into a load) is:\n    $$I_{\\text{out\\_node}} = I_1 + I_{D2} - I_{D1}$$\n*   **Gain Mechanism:**\n    *   An increase in $I_{\\text{in}}$ causes $I_{D1}$ to increase directly (gain of 1).\n    *   Simultaneously, the drop in $V_X$ causes $I_{D2}$ to increase (gain of $g_{m2}/g_{m1}$).\n    *   The total change in current at the high-impedance output node is $\\Delta I \\approx \\Delta I_{\\text{in}} (\\frac{g_{m2}}{g_{m1}} - 1)$.\n    *   This current difference develops a large voltage swing at $V_{\\text{out}}$ across the output impedance ($r_{o1} || r_{o2}$).\n\n**Summary:** The circuit takes a current input $I_{\\text{in}}$ and produces a voltage output $V_{\\text{out}}$. It combines a common-gate stage ($M_1$) to sense the input current and a common-source stage ($M_2$) to provide additional gain, summing their effects at the output node.",
        "format": "markdown",
        "sha256": "fa3fd8c9aba550e901c428c0abb31e308dfe9ec38aa5c80a31480801f2195129"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "It misconnects M2: its gate is driven by Vout and its drain feeds the input node, not vice versa. This misses the central feedback loop and incorrectly describes a high-gain, high-output-impedance stage instead of the low-input-resistance current-feedback buffer.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 16854,
        "total_tokens": 18630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15485,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 16854,
        "total_tokens": 18630,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15485,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part1-030-pmos-current-input-feedback",
      "part": "part1",
      "question_number": 30,
      "question": "Analyze the circuit shown in the figure.",
      "figures": [
        "tasks/part1-030-pmos-current-input-feedback/figure-24.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of its components, topology, and function.\n\n### 1. Component Identification\n*   **Transistors:**\n    *   **$M_1$**: An **NMOS** transistor. The arrow on the source terminal points outward. Its source is connected to the central node (let's call it $V_x$), its drain is connected to the output node $V_{out}$, and its gate is connected to a bias voltage $V_b$.\n    *   **$M_2$**: A **PMOS** transistor. The arrow on the source terminal points inward. Its source is connected to $V_{DD}$, its drain is connected to the central node $V_x$, and its gate is connected to the output node $V_{out}$.\n*   **Current Sources:**\n    *   **$I_1$**: A constant current source pulling current from $V_{DD}$ to the output node $V_{out}$.\n    *   **$I_{in}$**: An input current source injecting current from ground into the central node $V_x$.\n    *   **Unlabeled Current Source**: A constant current sink (downward arrow) drawing current from the central node $V_x$ to ground. Let's denote this as $I_{bias}$.\n\n### 2. Circuit Topology and Connections\n*   **Node $V_{out}$**: This is the output voltage node. It connects the current source $I_1$, the drain of $M_1$, and the gate of $M_2$.\n*   **Node $V_x$ (Central Node)**: This is the input node where the signal current $I_{in}$ is applied. It connects the drain of $M_2$, the source of $M_1$, the input current source $I_{in}$, and the bias current sink $I_{bias}$.\n*   **Feedback Loop**: The circuit features a negative feedback loop. The output voltage $V_{out}$ controls the gate of $M_2$. $M_2$'s drain current affects the voltage at node $V_x$, which in turn controls the current through $M_1$ (since $M_1$'s source is at $V_x$), ultimately affecting $V_{out}$.\n\n### 3. Circuit Operation Analysis\n\n**DC Operating Point:**\n*   **Current through $M_1$**: Looking at the output node $V_{out}$, the current $I_1$ flows into the node. Since the gate of $M_2$ draws negligible current, all of $I_1$ must flow down through the drain of $M_1$ to its source. Therefore, $I_{D1} = I_1$.\n*   **Voltage at Node $V_x$**: Since $I_{D1}$ is fixed at $I_1$ and the gate voltage $V_b$ is constant, the gate-source voltage $V_{GS1}$ of transistor $M_1$ is roughly constant (assuming saturation).\n    $$V_{GS1} = V_b - V_x \\approx \\text{constant}$$\n    This means the voltage at node $V_x$ is regulated to a constant value: $V_x \\approx V_b - V_{th,n} - V_{ov,1}$. This creates a **virtual ground** (or a constant voltage potential) at the input node.\n\n**Signal Analysis (Transimpedance Function):**\n*   **KCL at Node $V_x$**: The sum of currents entering the node equals the sum of currents leaving.\n    *   Entering: $I_{in}$ (from source), $I_{D2}$ (from PMOS $M_2$, flowing Source to Drain), $I_{D1}$ (from NMOS $M_1$, flowing Drain to Source).\n    *   Leaving: $I_{bias}$ (downward current source).\n    *   Equation: $I_{in} + I_{D2} + I_{D1} = I_{bias}$.\n*   Substituting $I_{D1} = I_1$:\n    $$I_{D2} = I_{bias} - I_1 - I_{in}$$\n*   This equation shows that the current through transistor $M_2$ ($I_{D2}$) is directly modulated by the input current $I_{in}$. Specifically, an increase in $I_{in}$ causes a decrease in $I_{D2}$.\n*   **Output Voltage**: The current $I_{D2}$ through the PMOS transistor $M_2$ is determined by its source-gate voltage $V_{SG2} = V_{DD} - V_{out}$.\n    $$I_{D2} \\propto (V_{DD} - V_{out} - |V_{th,p}|)^2$$\n    If $I_{in}$ increases, $I_{D2}$ decreases. For the current to decrease, the overdrive voltage $(V_{DD} - V_{out} - |V_{th,p}|)$ must decrease, which implies that **$V_{out}$ must increase** (move closer to $V_{DD}$).\n\n### 4. Conclusion\nThis circuit functions as a **Transimpedance Amplifier** (Current-to-Voltage Converter).\n\n*   **Input**: Current $I_{in}$.\n*   **Output**: Voltage $V_{out}$.\n*   **Mechanism**: The negative feedback through $M_2$ keeps the input node voltage $V_x$ constant (low input impedance). The input current forces a change in the current through $M_2$, which translates to a change in the gate voltage of $M_2$ (which is $V_{out}$).\n*   **Gain**: For small signals, the transimpedance gain is approximately $1/g_{m2}$ (where $g_{m2}$ is the transconductance of $M_2$).\n    $$ \\frac{v_{out}}{i_{in}} \\approx \\frac{1}{g_{m2}} $$",
        "format": "markdown",
        "sha256": "8f4b41d45ad9b6addd609d3ca14fa377efd2435b8059f83dfc83e3dd3496e7a8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M1 as the common-gate NMOS and M2 as the PMOS feedback device driven by Vout, traces feedback to the input node, and gives the low input impedance and vout/iin ≈ 1/gm2. This meets the golden solution’s full-credit rule.",
          "golden_solution_sha256": "81b07f946459ec3d1a0c51926785b2333e0320bb99c892d5929e040324abeaf8",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 12298,
        "total_tokens": 14074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10972,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1776,
        "output_tokens": 12298,
        "total_tokens": 14074,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10972,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes, the circuit fails to oscillate if the capacitors become arbitrarily large.**\n\nHere is the step-by-step analysis:\n\n1.  **Identify the Circuit:** The figure shows a **ring oscillator** composed of three inverters (NOT gates) connected in a loop. The capacitors $C_L$ represent the load capacitance at each node.\n\n2.  **Mechanism of Oscillation:** A ring oscillator with an odd number of stages (like 3) is inherently unstable. If the input to the first inverter is low (0), the output of the third inverter will eventually become high (1), which feeds back to the input, causing the state to flip. This continuous flipping creates an oscillation.\n\n3.  **Role of Capacitors:** The capacitors $C_L$ determine the speed of the circuit. The time it takes for an inverter to switch its output (propagation delay, $t_p$) is largely determined by the time required to charge or discharge the load capacitor. The relationship is approximately $t_p \\propto R \\cdot C_L$, where $R$ is the effective resistance of the inverter's transistors.\n\n4.  **Frequency of Oscillation:** The period of oscillation ($T$) is the sum of the propagation delays through all stages (twice, for a full cycle of high and low). For a 3-stage ring oscillator, $T \\approx 6 \\cdot t_p$. Therefore, the frequency of oscillation is $f = 1/T \\propto 1/(R \\cdot C_L)$.\n\n5.  **Limit of Large Capacitance:** As the capacitance $C_L$ becomes arbitrarily large ($C_L \\rightarrow \\infty$):\n    *   The time constant $\\tau = R \\cdot C_L$ approaches infinity.\n    *   The propagation delay $t_p$ approaches infinity.\n    *   The frequency of oscillation $f$ approaches zero.\n\n**Conclusion:**\nIf the capacitors are infinitely large, the voltage at the nodes cannot change in any finite amount of time (since $I = C \\frac{dV}{dt}$, for a finite current $I$ and infinite $C$, $\\frac{dV}{dt} = 0$). The circuit will effectively be \"frozen\" in its initial state (or a metastable state) and will not switch, meaning it **fails to oscillate**.",
        "format": "markdown",
        "sha256": "e3b26947982c407e06833759bd92dd2d4ae2d443aa77df67156bb8e121975750"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly notes that increasing all three capacitances increases delay and lowers frequency, but it concludes that the ring fails to oscillate. The central result is that it continues oscillating at a lower frequency; the golden solution caps this contrary conclusion at 1.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 5357,
        "total_tokens": 7170,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4840,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 5357,
        "total_tokens": 7170,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4840,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis:\n\n**Answer: No, the circuit does not fail to oscillate.**\n\n**Explanation:**\n\n1.  **Circuit Identification:** The circuit shown is a **Ring Oscillator**. It consists of an odd number of inverters (three NOT gates) connected in a closed loop. This configuration is inherently unstable because the logic level at the input is constantly inverted and fed back, causing the circuit to flip states continuously.\n\n2.  **Role of Capacitors ($C_L$):** The capacitors labeled $C_L$ represent load capacitance at the output of each inverter. In a real circuit, every node has some capacitance to ground. These capacitors, combined with the output resistance of the inverters ($R_{out}$), create an RC time constant ($\\tau = R_{out} \\cdot C_L$) for each stage. This time constant determines how fast the voltage at each node can change (propagation delay).\n\n3.  **Effect of Increasing Capacitance:** The frequency of oscillation ($f$) for a ring oscillator is inversely proportional to the total delay around the loop.\n    $$f \\approx \\frac{1}{2 \\cdot N \\cdot t_p}$$\n    where $N$ is the number of stages (3) and $t_p$ is the propagation delay of each stage. Since the delay $t_p$ is proportional to the time constant $\\tau$ (and thus proportional to $C_L$), increasing the capacitance increases the delay.\n    $$f \\propto \\frac{1}{C_L}$$\n\n4.  **Conclusion:** If the capacitors become arbitrarily large, the time constant becomes very large, and the propagation delay increases significantly. Consequently, the **frequency of oscillation will decrease** (approaching zero). However, as long as the capacitors are finite values, the voltage will eventually change, causing the inverters to switch states. Therefore, the circuit will continue to oscillate, just at a very low frequency. It would only \"fail\" to oscillate in the theoretical limit where the capacitance is infinite ($C_L = \\infty$), effectively freezing the circuit.",
        "format": "markdown",
        "sha256": "b58eefbc6eeea60f40856e64e9293984d4f1c41ac9b980c68d4db7224eb3eba8"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the ring continues oscillating at a lower frequency, with increasing load capacitance increasing stage delay and reducing frequency. This matches the full-credit rule.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 7828,
        "total_tokens": 9641,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7363,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 7828,
        "total_tokens": 9641,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7363,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large",
      "part": "part2",
      "question_number": 1,
      "question": "Does the circuit in the figure fail to oscillate if the three capacitors become arbitrarily large?",
      "figures": [
        "tasks/part2-001-fail-oscillate-three-capacitors-become-arbitrarily-large/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the analysis:\n\n**1. Identification of the Circuit**\nThe circuit shown is a **Ring Oscillator**. It consists of an odd number of inverters (three, in this case) connected in a closed loop. The output of the last inverter is fed back to the input of the first. This topology is inherently unstable and produces a continuous oscillating signal. The capacitors labeled $C_L$ represent load capacitances at each node.\n\n**2. Role of the Capacitors**\nThe capacitors $C_L$, in combination with the output resistance of the inverters (let's call it $R_{out}$), create an RC time constant ($\\tau = R_{out} C_L$). This time constant determines the propagation delay of each inverter stage. It takes time for the capacitor to charge or discharge to the switching threshold of the next inverter.\n\n**3. Effect of Increasing Capacitance**\nThe frequency of oscillation ($f$) for a ring oscillator is inversely proportional to the propagation delay of the stages.\n$$f \\approx \\frac{1}{2 \\cdot N \\cdot t_{pd}}$$\nwhere $N$ is the number of stages (3) and $t_{pd}$ is the delay per stage (proportional to $R_{out} C_L$).\n\nTherefore, as the capacitors $C_L$ become larger:\n*   The time constant $\\tau$ increases.\n*   The propagation delay $t_{pd}$ increases.\n*   The frequency of oscillation $f$ decreases.\n\n**4. Does it fail to oscillate?**\n**No, the circuit does not fail to oscillate.**\n\nHere is the theoretical justification:\n*   **Phase Condition:** For oscillation to occur, the total phase shift around the loop must be $360^{\\circ}$ (or $0^{\\circ}$). The three inverters provide a DC phase shift of $3 \\times 180^{\\circ} = 540^{\\circ}$ (which is effectively $180^{\\circ}$). The RC networks formed by the inverters and capacitors provide additional phase lag. Oscillation occurs at the specific frequency where the RC networks provide the remaining $180^{\\circ}$ of phase shift. This frequency is $\\omega = \\frac{\\sqrt{3}}{R C_L}$. This frequency exists for any finite value of $C_L$.\n*   **Gain Condition:** The loop gain must be at least 1. At the oscillation frequency derived above, the gain of each stage is determined by the DC gain of the inverter ($A_0$). Specifically, the magnitude of the gain per stage is $A_0 / 2$. The total loop gain is $(A_0/2)^3$. As long as the inverter's DC gain $A_0 \\ge 2$ (which is true for standard logic gates), the circuit will oscillate. This condition is independent of the capacitor value.\n\n**Conclusion**\nWhile making the capacitors \"arbitrarily large\" will cause the frequency of oscillation to approach zero (making the oscillation extremely slow), the circuit will theoretically continue to oscillate for any finite capacitance value. It does not stop oscillating; it just slows down.",
        "format": "markdown",
        "sha256": "b735d6ee170d4555a68f91705098385c74d8cc85f30f63c21839d30222f74fd6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that the ring continues oscillating while its frequency decreases as the three capacitances increase. The delay and small-signal phase/gain arguments support the conclusion.",
          "golden_solution_sha256": "382bd8dbcc1993e2438bdfd3faf5268719f050e1964cb818b2278171cb2c25bf",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 9552,
        "total_tokens": 11365,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8843,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1813,
        "output_tokens": 9552,
        "total_tokens": 11365,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8843,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the analysis of the ring oscillator circuit:\n\n1.  **Oscillation Frequency:** The circuit is a 3-stage ring oscillator. The oscillation frequency $f_{osc}$ is inversely proportional to the delay of each stage. The delay $t_d$ is proportional to the load capacitance $C_L$ (specifically $t_d \\approx 0.69 R_{on} C_L$). Therefore, $f_{osc} \\propto \\frac{1}{C_L}$. If the capacitors are doubled ($2C_L$), the oscillation frequency is halved ($f_{osc}/2$).\n\n2.  **Phase Noise Scaling:** The phase noise $\\mathcal{L}(\\Delta f)$ of a ring oscillator (in the $1/f^2$ region dominated by thermal noise) can be approximated by the relationship:\n    $$ \\mathcal{L}(\\Delta f) \\propto \\frac{f_{osc}^2}{P_{diss}} $$\n    where $P_{diss}$ is the power dissipation.\n    *   The dynamic power dissipation is $P_{diss} = C_{total} V^2 f_{osc} = 3 C_L V^2 f_{osc}$.\n    *   Since $f_{osc} \\propto 1/C_L$, the power dissipation $P_{diss} \\propto C_L \\cdot (1/C_L) = \\text{constant}$. The power consumption remains roughly the same.\n    *   Therefore, the phase noise is primarily proportional to the square of the oscillation frequency: $\\mathcal{L}(\\Delta f) \\propto f_{osc}^2$.\n\n3.  **Calculation:**\n    Since the frequency is halved ($f_{osc}' = f_{osc} / 2$), the phase noise becomes:\n    $$ \\mathcal{L}'(\\Delta f) \\propto \\left( \\frac{f_{osc}}{2} \\right)^2 = \\frac{1}{4} f_{osc}^2 $$\n    This means the phase noise power decreases by a factor of 4.\n\nIn decibels, this corresponds to a reduction of $10 \\log_{10}(1/4) \\approx -6 \\text{ dB}$.\n\n**Answer:** The phase noise decreases by a factor of 4 (or improves by 6 dB).",
        "format": "markdown",
        "sha256": "c747784ec9a84718b5db8eb91a4a88410477b9fd58194a32120159bd3e8ab8e7"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and gives a fourfold phase-noise decrease (about 6 dB), consistent with the full-credit rule.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 11432,
        "total_tokens": 13243,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 11432,
        "total_tokens": 13243,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10904,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, which shows a 3-stage ring oscillator with load capacitors $C_L$, here is the analysis of what happens to the phase noise if the capacitors are doubled:\n\n1.  **Oscillation Frequency Decreases:**\n    The oscillation frequency ($f_{osc}$) of a ring oscillator is inversely proportional to the delay of each stage. The delay is primarily determined by the RC time constant of the inverter driving the load capacitor ($t_d \\propto R_{on} C_L$).\n    $$f_{osc} \\approx \\frac{1}{2 N t_d} \\propto \\frac{1}{C_L}$$\n    If the capacitors $C_L$ are doubled, the delay doubles, and the **oscillation frequency is halved**.\n\n2.  **Phase Noise Decreases:**\n    The phase noise $\\mathcal{L}(\\Delta f)$ at an offset frequency $\\Delta f$ for a ring oscillator is generally proportional to the square of the oscillation frequency (in the $1/f^2$ thermal noise region). A common approximation (derived from Leeson's model or specific ring oscillator analysis) is:\n    $$\\mathcal{L}(\\Delta f) \\propto \\frac{1}{P_{diss}} \\left( \\frac{f_{osc}}{Q \\Delta f} \\right)^2$$\n    *   **Power ($P_{diss}$):** The dynamic power dissipation is $P = C_{total} V_{DD}^2 f_{osc}$. Since $C_{total}$ doubles and $f_{osc}$ halves, the power consumption remains roughly **constant**.\n    *   **Quality Factor ($Q$):** For a ring oscillator with RC-dominated delays, the effective Q factor is largely determined by the number of stages and the phase shift per stage (60 degrees for a 3-stage ring), making it roughly **independent** of the specific R and C values.\n    *   **Frequency ($f_{osc}$):** As established, $f_{osc}$ is halved.\n\n    Substituting these into the proportionality:\n    $$\\mathcal{L}(\\Delta f) \\propto (f_{osc})^2 \\propto \\left(\\frac{1}{C_L}\\right)^2$$\n    Since $f_{osc}$ becomes $1/2$ of its original value, the phase noise term $(f_{osc})^2$ becomes $(1/2)^2 = 1/4$.\n\n**Conclusion:**\nIf the three capacitors are doubled, the **phase noise decreases** (improves). Specifically, it decreases by a factor of 4, which corresponds to a reduction of **6 dB**.\n\nIntuitively, larger capacitors store more energy ($E \\propto C V^2$), making the oscillator signal more robust against noise perturbations, although this comes at the cost of a lower oscillation frequency.",
        "format": "markdown",
        "sha256": "4db44139925211ea66f02b0168b32857cef651e43c65ad93d153712314a64d20"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly states that doubling the capacitors halves the oscillation frequency and reduces phase noise by a factor of four (6 dB) at a fixed offset, consistent with the full-credit rule.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 10909,
        "total_tokens": 12720,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 10909,
        "total_tokens": 12720,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-002-phase-noise-three-capacitors-doubled",
      "part": "part2",
      "question_number": 2,
      "question": "What happens to the phase noise if the three capacitors in the figure are doubled?",
      "figures": [
        "tasks/part2-002-phase-noise-three-capacitors-doubled/figure-05.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the analysis of the ring oscillator circuit:\n\n1.  **Oscillation Frequency:** The circuit is a 3-stage ring oscillator. The oscillation frequency $f_{osc}$ is inversely proportional to the delay of each stage. The delay is determined by the time constant $\\tau = R_{on}C_L$, where $R_{on}$ is the effective resistance of the inverters.\n    *   If $C_L$ is doubled, the delay of each stage doubles.\n    *   Consequently, the oscillation frequency $f_{osc}$ is **halved** ($f_{new} = f_{old} / 2$).\n\n2.  **Power Dissipation:** The dynamic power dissipation of the oscillator is given by $P \\approx C_{total} V_{DD}^2 f_{osc}$. Since the total capacitance is proportional to $C_L$ and $f_{osc}$ is inversely proportional to $C_L$, the power dissipation remains roughly **constant** ($P \\propto C_L \\cdot \\frac{1}{C_L} = \\text{const}$).\n\n3.  **Phase Noise:** The phase noise $\\mathcal{L}(\\Delta f)$ of a ring oscillator (dominated by thermal noise) is generally proportional to the square of the oscillation frequency divided by the power dissipation (or proportional to $1/C_L^2$ based on charge swing arguments).\n    *   Using the proportionality $\\mathcal{L}(\\Delta f) \\propto \\frac{f_{osc}^2}{P_{diss}}$:\n    *   Since $P_{diss}$ is constant and $f_{osc}$ is halved, the phase noise becomes proportional to $(1/2)^2 = 1/4$.\n    *   Alternatively, using the relationship $\\mathcal{L}(\\Delta f) \\propto \\frac{1}{C_L^2}$ (derived from the Hajimiri-Lee model where phase noise is inversely proportional to the square of the maximum charge swing $q_{max} = C_L V_{swing}$): doubling $C_L$ reduces the phase noise by a factor of $2^2 = 4$.\n\n**Conclusion:**\nIf the three capacitors are doubled, the phase noise **decreases by a factor of 4** (or **improves by 6 dB**). This is because the larger capacitors increase the energy stored in the oscillator (larger charge swing), making it more robust against noise perturbations, despite the lower operating frequency.",
        "format": "markdown",
        "sha256": "736d60ba225d480c82e699f84c1cf4d0cced91bc5cd51c289a4074915ced1212"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that doubling the capacitors halves the oscillation frequency and reduces phase noise by a factor of four (about 6 dB), with a supporting frequency-squared argument.",
          "golden_solution_sha256": "c8a3a6ddcab3a54151ffe61cb3e809a6731a66beda02e9f8898ea9c435318b06",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 6051,
        "total_tokens": 7862,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5502,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1811,
        "output_tokens": 6051,
        "total_tokens": 7862,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5502,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit will fail to oscillate if $C_L$ becomes arbitrarily large.\n\nHere is the step-by-step analysis:\n\n1.  **Circuit Identification:** The circuit consists of three inverters connected in a ring loop. This is a standard **ring oscillator**. Normally, an odd number of inverters in a loop creates an unstable system that oscillates because there is no stable DC state (if the input is 0, the output is 1, which feeds back to make the input 1, creating a contradiction).\n\n2.  **Role of Propagation Delay:** For a ring oscillator to oscillate, there must be a sufficient phase shift around the loop. The three inverters provide a $180^\\circ$ phase shift (inversion) at low frequencies. To achieve the $360^\\circ$ (or $0^\\circ$) total phase shift required for positive feedback and oscillation, the reactive components (capacitances) must provide an additional $180^\\circ$ of phase lag. This phase lag comes from the propagation delays of the inverters.\n\n3.  **Effect of $C_L$:** The capacitor $C_L$ is connected to the output of the first inverter. It creates a low-pass filter with the output resistance of the inverter, introducing a pole at a frequency $\\omega_p = 1/(R_{out}C_L)$.\n    *   As $C_L$ increases, this pole moves to a lower frequency.\n    *   This significantly increases the propagation delay of the first stage.\n\n4.  **Stability Analysis (Barkhausen Criterion):** For oscillation to sustain, the loop gain must be at least 1 at the frequency where the total phase shift is $360^\\circ$.\n    *   With a very large $C_L$, the first stage acts as a dominant pole with a very low cutoff frequency.\n    *   At the frequency where the other two stages (and the first stage's pole) provide the necessary $180^\\circ$ of additional phase lag, the gain of the first stage will be heavily attenuated (rolled off) because the frequency is much higher than its new, very low cutoff frequency.\n    *   Consequently, the total loop gain drops below 1.\n\n5.  **Result:** When the loop gain falls below 1, the oscillation condition is no longer met. The circuit becomes stable and will settle at a metastable DC operating point, typically around $V_{DD}/2$ (the switching threshold of the inverters). In this state, all inverters act as linear amplifiers, and the circuit consumes static power but does not oscillate.\n\nTherefore, if $C_L$ is arbitrarily large, the circuit **fails to oscillate**.",
        "format": "markdown",
        "sha256": "809a0c6e62d9b85ab817b4d6eb3729d75c734bd353a7b18434bd5bc6c3a20e77"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large capacitance on one node can stop oscillation and explains the dominant pole, gain roll-off, and failure of the Barkhausen condition. The DC-settling details are secondary and do not undermine the essential answer.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 9863,
        "total_tokens": 11581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 9863,
        "total_tokens": 11581,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9276,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit will fail to oscillate if $C_L$ becomes arbitrarily large.\n\n**Reasoning:**\n\n1.  **Circuit Identification:** The circuit shown is a ring oscillator consisting of three inverters connected in a loop. Normally, an odd number of inverters in a loop creates an unstable system that oscillates because the total phase shift is $180^\\circ$ (from the three inversions) plus additional phase shift from delays, leading to positive feedback at a specific frequency.\n\n2.  **Role of $C_L$:** The capacitor $C_L$ is connected to the output of the first inverter. This creates a low-pass filter (an RC circuit) with the output resistance of the inverter. This adds a significant time constant ($\\tau = R \\cdot C_L$) and a pole to the transfer function of that stage.\n\n3.  **Barkhausen Stability Criterion:** For a circuit to oscillate, the loop gain must be at least 1 ($|A\\beta| \\ge 1$) and the total phase shift around the loop must be $360^\\circ$ (or $0^\\circ$) at the oscillation frequency.\n    *   The three inverters provide a static phase shift of $3 \\times 180^\\circ = 540^\\circ$, which is equivalent to $180^\\circ$.\n    *   To reach $360^\\circ$, the reactive components (capacitors) must provide an additional $180^\\circ$ of phase lag.\n    *   As $C_L$ becomes arbitrarily large, the pole frequency of the first stage ($\\omega_p = 1/RC_L$) approaches zero. This stage acts like an integrator, contributing up to $90^\\circ$ of phase lag. The other two stages contribute the remaining required phase lag.\n    *   However, at the frequency where the total phase shift reaches $360^\\circ$, the magnitude of the gain for the first stage will be extremely low because the frequency is much higher than its pole frequency ($\\omega \\gg 1/RC_L$). The gain drops as $1/(\\omega C_L)$.\n    *   Consequently, the total loop gain drops below 1.\n\n4.  **Stability Analysis:** Mathematically, if you linearize the inverters around their switching threshold (metastable point), the characteristic equation of the system shows that for a sufficiently large time constant $\\tau_1$ (proportional to $C_L$), the roots of the system move to the left half of the complex plane. This means the system becomes **stable**. Instead of oscillating, the circuit voltages will settle to a steady DC value (approximately $V_{DD}/2$), and the oscillation will stop (or fail to start).\n\nIn practical terms, the capacitor would take so long to charge and discharge through the inverter's resistance that leakage currents and noise would dominate, preventing the voltage from ever crossing the switching threshold of the next inverter.",
        "format": "markdown",
        "sha256": "a5fbd6af6c8f4d20eac5334294b4fe0090f871bbc19d541fa8d7bb7e91c4b68b"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large load capacitance on one node can stop oscillation, explaining that its dominant low-frequency pole causes excessive loop-gain roll-off so the Barkhausen condition fails. The secondary stability discussion does not undermine the essential answer.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 9610,
        "total_tokens": 11328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8961,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 9610,
        "total_tokens": 11328,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8961,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-003-fail-oscillate-cl-becomes-arbitrarily-large",
      "part": "part2",
      "question_number": 3,
      "question": "Does the circuit in the figure fail to oscillate if CL becomes arbitrarily large?",
      "figures": [
        "tasks/part2-003-fail-oscillate-cl-becomes-arbitrarily-large/figure-06.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the circuit fails to oscillate if $C_L$ becomes arbitrarily large.\n\n**Reasoning:**\n\n1.  **Circuit Type:** The circuit shown is a ring oscillator consisting of three inverters (NOT gates) connected in a loop. Normally, an odd number of inverters in a feedback loop creates an unstable system that oscillates because the total phase shift around the loop reaches $360^{\\circ}$ (or $0^{\\circ}$) at some frequency, satisfying the Barkhausen criterion for oscillation. The three inversions provide $180^{\\circ}$ of phase shift, and the propagation delays of the gates provide the additional $180^{\\circ}$ required.\n\n2.  **Effect of $C_L$:** The capacitor $C_L$ is connected to the node between the first and second inverter. This creates an RC low-pass filter with the output resistance of the first inverter. This adds a pole to the system's transfer function at a frequency $\\omega_p = \\frac{1}{R_{out}C_L}$.\n\n3.  **Phase Shift Condition:** For the circuit to oscillate, the total loop phase shift must be a multiple of $360^{\\circ}$.\n    *   The three inverters contribute $180^{\\circ}$ (due to signal inversion).\n    *   The RC network formed by $C_L$ can contribute a maximum of $90^{\\circ}$ of phase lag.\n    *   The remaining phase shift (at least $90^{\\circ}$) must come from the intrinsic delays (parasitic poles) of the inverters.\n\n4.  **Gain Condition:** As $C_L$ becomes arbitrarily large, the pole frequency $\\omega_p$ approaches zero. This means the gain of the loop starts rolling off at a very low frequency.\n    *   By the time the frequency is high enough for the intrinsic inverter delays to provide the necessary additional phase shift to reach the oscillation condition (total $360^{\\circ}$), the signal has been heavily attenuated by the large capacitor.\n    *   Mathematically, the loop gain magnitude is proportional to $\\frac{1}{\\omega R C_L}$. As $C_L \\to \\infty$, the loop gain drops below 1 at the frequency where the phase condition would be met.\n\n5.  **Stability:** With a very large $C_L$, the circuit behaves like a stable negative feedback amplifier. The large capacitor slows down the transitions so much that the \"regenerative\" switching action is suppressed. The circuit will settle at a metastable DC equilibrium point (approximately $V_{DD}/2$), where the input and output voltages balance out, and will not oscillate.",
        "format": "markdown",
        "sha256": "a1024ddc9ba3cdd85c66476ff949aff6ebdac408e7713fba9be488cb5551a18d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes that arbitrarily large capacitance on one node can stop oscillation, explaining that its dominant pole causes gain roll-off so the loop cannot meet the Barkhausen condition. The approximate pole and time-domain descriptions are consistent with the essential answer.",
          "golden_solution_sha256": "f6dd3ed123c88a59472f7a76de74df7e33b3e73498632bd24bc1ea808e4efcbc",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 12127,
        "total_tokens": 13845,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11541,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1718,
        "output_tokens": 12127,
        "total_tokens": 13845,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11541,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, which is a **3-stage CMOS ring oscillator**, here is the step-by-step analysis of what happens when the widths of the NMOS and PMOS devices are doubled:\n\n1.  **Effect on Current and Capacitance:**\n    *   Doubling the width ($W$) of the transistors doubles their drive current ($I_D \\propto W$).\n    *   Doubling the width also doubles the parasitic capacitances at the nodes (gate capacitance, drain capacitance, etc., so $C \\propto W$).\n\n2.  **Effect on Oscillation Frequency:**\n    *   The oscillation frequency of a ring oscillator is roughly inversely proportional to the delay of each stage ($f \\approx 1 / (2 \\cdot N \\cdot t_d)$).\n    *   The delay $t_d$ is proportional to $C / I$ (time to charge/discharge the capacitor).\n    *   Since both $C$ and $I$ double, the ratio $C/I$ remains constant. Therefore, the **oscillation frequency remains roughly unchanged**.\n\n3.  **Effect on Power Consumption:**\n    *   The power consumption is $P = I \\cdot V_{DD}$. Since the current $I$ doubles and $V_{DD}$ is constant, the **power consumption doubles**.\n\n4.  **Effect on Phase Noise:**\n    *   Phase noise ($\\mathcal{L}$) in oscillators is generally inversely proportional to the signal power (or carrier power) for a given topology and frequency offset. A common approximation is $\\mathcal{L} \\propto \\frac{kT}{P}$.\n    *   Alternatively, looking at the noise charge: The maximum charge swing $q_{max} = C \\cdot V_{swing}$ doubles (since $C$ doubles). The phase noise is inversely proportional to $q_{max}^2$ (which quadruples). The thermal noise current power is proportional to $g_m$ (which doubles). So, Phase Noise $\\propto \\frac{\\text{Noise Current}}{q_{max}^2} \\propto \\frac{2}{4} = \\frac{1}{2}$.\n\n**Conclusion:**\nBecause the power consumption doubles while the frequency stays the same, the signal-to-noise ratio improves. Specifically, the **phase noise decreases by a factor of 2 (improves by 3 dB)**.",
        "format": "markdown",
        "sha256": "8aee3689025b40a97a788089500e6c429357450541e97ec5f2dafd88155cba49"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes about a 3 dB phase-noise reduction. Its scaling argument captures the key result: node charge-swing squared grows by four while device noise power grows by two, giving half the noise-to-signal ratio.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 2913,
        "total_tokens": 5445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2390,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 2913,
        "total_tokens": 5445,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2390,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, which is a **3-stage CMOS ring oscillator**, here is the analysis of what happens when the widths of the NMOS and PMOS devices are doubled:\n\n1.  **Frequency remains constant:** The oscillation frequency of a ring oscillator is determined by the delay of each stage, which is roughly proportional to $C_L / I_D$ (Load Capacitance divided by Drive Current).\n    *   Doubling the width ($W$) doubles the drive current ($I_D \\propto W$).\n    *   Doubling the width also doubles the parasitic capacitances ($C_L \\propto W$).\n    *   Since both the numerator and denominator double, the delay per stage remains roughly the same, and the **oscillation frequency ($f_0$) stays approximately constant**.\n\n2.  **Power consumption increases:** The total current drawn from the supply doubles, so the power dissipation ($P = I \\cdot V_{DD}$) doubles.\n\n3.  **Phase Noise decreases:** Phase noise in a ring oscillator is generally inversely proportional to the power dissipation (or the device size) for a given frequency. A common approximation for phase noise $\\mathcal{L}(\\Delta f)$ is:\n    $$ \\mathcal{L}(\\Delta f) \\propto \\frac{k T}{C V_{swing}^2} $$\n    *   Since the capacitance $C$ doubles (due to doubled widths), the denominator increases by a factor of 2.\n    *   Alternatively, looking at it through signal-to-noise ratio: the thermal noise voltage power is inversely proportional to $g_m$ (which doubles), so the noise power is halved. The signal swing remains the same. Thus, the Signal-to-Noise Ratio (SNR) improves.\n\n**Conclusion:**\nDoubling the widths of the devices will **reduce the phase noise by a factor of 2** (or approximately **3 dB**). The oscillator will consume more power but operate at roughly the same frequency with better phase noise performance.",
        "format": "markdown",
        "sha256": "cb30cdf43fae2430a3f7765cefc5f570b3a7a2e9ebb938fcc8e2c60a1350a9bc"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly predicts about a 3 dB phase-noise reduction, with the node-capacitance scaling that supports this result; the frequency and power trends are also consistent with the golden solution.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 4304,
        "total_tokens": 6836,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3867,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 4304,
        "total_tokens": 6836,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3867,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-004-double-widths-nmos-and-pmos-devices-phase",
      "part": "part2",
      "question_number": 4,
      "question": "If we double the widths of the NMOS and PMOS devices in the figure, what happens to the phase noise?",
      "figures": [
        "tasks/part2-004-double-widths-nmos-and-pmos-devices-phase/figure-07.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, this is a **3-stage ring oscillator** composed of CMOS inverters.\n\nTo determine the effect of doubling the widths ($W$) of the NMOS and PMOS devices on the phase noise, we can analyze the scaling of the relevant circuit parameters:\n\n1.  **Transconductance ($g_m$) and Current ($I_D$):** The transconductance and the drain current of a MOSFET are proportional to its width ($W$). Therefore, doubling the width doubles the $g_m$ and the current $I_D$ ($g_m \\rightarrow 2g_m$, $I_D \\rightarrow 2I_D$).\n2.  **Capacitance ($C$):** The parasitic capacitances at the nodes (gate capacitance of the next stage and drain capacitance of the current stage) are also proportional to the width $W$. Therefore, doubling the width doubles the total load capacitance ($C \\rightarrow 2C$).\n3.  **Oscillation Frequency ($f_0$):** The delay of each inverter stage is roughly proportional to $C / g_m$ (or $C \\cdot V / I$). Since both capacitance and current/transconductance double, the delay remains constant. Consequently, the oscillation frequency $f_0$ remains unchanged.\n4.  **Noise Voltage:** The thermal noise current spectral density is proportional to $g_m$ ($\\overline{i_n^2} \\propto g_m$). The noise voltage spectral density at the output node is roughly $\\overline{v_n^2} \\approx \\overline{i_n^2} / g_m^2 \\propto 1/g_m$. Since $g_m$ doubles, the noise voltage power is halved.\n5.  **Slew Rate:** The slew rate ($dV/dt$) is proportional to $I_D / C$. Since both current and capacitance double, the slew rate remains constant.\n6.  **Phase Noise:** Phase noise is fundamentally related to timing jitter, which is the ratio of noise voltage to slew rate ($\\text{Jitter} \\propto v_n / \\text{SlewRate}$). Since the slew rate is constant and the noise voltage power is halved, the timing jitter variance is halved.\n\nSince phase noise power is proportional to the jitter variance, halving the jitter variance reduces the phase noise power by a factor of 2.\n\nIn decibels (dB), this change is:\n$$ 10 \\log_{10}(1/2) \\approx -3 \\text{ dB} $$\n\n**Answer:** The phase noise **decreases by 3 dB**.",
        "format": "markdown",
        "sha256": "25c5403f1e4ffa9ee8b038485dac46c6f7b21218178d595ab332e53f63289e03"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly concludes a 3 dB reduction and gives a consistent scaling argument: width doubles the thermal-noise current PSD and node capacitance, while frequency and slew rate remain roughly constant, yielding half the jitter variance. It does not incorrectly claim that wider devices reduce thermal noise.",
          "golden_solution_sha256": "f9299196b0b81aa8f665614cd6e16eba9d8392f73cfe6422876d92d225ddc94e",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 4060,
        "total_tokens": 6592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3487,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2532,
        "output_tokens": 4060,
        "total_tokens": 6592,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3487,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance $R_X$ seen looking into the supply node of the ring oscillator, we analyze the circuit at its metastable DC operating point (the equilibrium point where the oscillation would stop if there were no noise, typically $V_{in} = V_{out} = V_{DD}/2$).\n\n**1. Circuit Analysis:**\nThe circuit consists of three identical inverters connected in a ring. The supply node (top rail) is connected to the $V_{DD}$ terminal of all three inverters. The ground node is connected to the $V_{SS}$ terminal of all three inverters.\n\n**2. Small-Signal Model of an Inverter:**\nConsider a single CMOS inverter biased at $V_{in} = V_{out} = V_{DD}/2$. At this point, both the NMOS and PMOS transistors are in saturation.\nLet $g_m$ be the transconductance of the transistors (assuming symmetry, $g_{mn} = g_{mp} = g_m$).\nWhen a small-signal voltage $v_x$ is applied to the supply node:\n*   The source of the PMOS is at $v_x$.\n*   The gate is at $v_{in}$.\n*   The source-gate voltage is $v_{sg} = v_x - v_{in}$.\n*   The small-signal current flowing into the supply node (source of PMOS) is approximately $i_s \\approx g_m v_{sg} = g_m(v_x - v_{in})$. (Ignoring output resistance $r_o$ for simplicity as $g_m r_o \\gg 1$).\n\n**3. Feedback Effect in the Ring:**\nIn the ring oscillator configuration, the inputs are driven by the outputs of the previous stages.\n$v_{out} = -A v_{in} + \\frac{A}{2} v_x$ (where $A$ is the large open-loop gain of the inverter).\nDue to the high gain and the ring structure (loop gain $-A^3$), the internal nodes tend to follow the common-mode shift of the supply.\nSolving the system of equations for the three stages:\n$v_{in1} = v_{out3}$, $v_{in2} = v_{out1}$, $v_{in3} = v_{out2}$.\nWe find that for a large gain $A$, the small-signal voltage at the input and output of each inverter is approximately half of the supply perturbation:\n$v_{in} \\approx v_{out} \\approx \\frac{v_x}{2}$.\n\n**4. Calculating Resistance:**\nSubstitute $v_{in} \\approx v_x/2$ into the current equation for one inverter:\n$i_{s,1} \\approx g_m (v_x - \\frac{v_x}{2}) = \\frac{g_m v_x}{2}$.\n\nThe small-signal resistance of one inverter looking into the supply node is:\n$R_{inv} = \\frac{v_x}{i_{s,1}} = \\frac{v_x}{g_m v_x / 2} = \\frac{2}{g_m}$.\n\n**5. Total Resistance:**\nSince the three inverters are connected in parallel to the supply node, the total resistance $R_X$ is the parallel combination of the three individual resistances:\n$R_X = R_{inv} \\parallel R_{inv} \\parallel R_{inv} = \\frac{R_{inv}}{3}$.\n\n$R_X = \\frac{1}{3} \\left( \\frac{2}{g_m} \\right) = \\frac{2}{3g_m}$.\n\n**Answer:**\nThe small-signal resistance seen looking into the supply node is approximately **$\\frac{2}{3g_m}$**, where $g_m$ is the transconductance of the transistors in the inverters (assuming symmetric NMOS and PMOS devices). If $G_m$ represents the total transconductance of an inverter stage ($G_m = g_{mn} + g_{mp} = 2g_m$), then $R_X = \\frac{4}{3G_m}$.",
        "format": "markdown",
        "sha256": "86db42d370d1953d0b08b2f21410a307be090cc4d3cb739c6e77ebff13c7ed37"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer analyzes only the static metastable point and gives a gm-based resistance, missing the oscillation-driven charging and discharging of the load capacitances that sets the supply resistance. The golden solution assigns this static-analysis answer 1.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 13424,
        "total_tokens": 15953,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12508,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 13424,
        "total_tokens": 15953,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12508,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance $R_X$ looking into the supply node of the ring oscillator, we analyze the small-signal model of the circuit.\n\n**1. Circuit Analysis**\nThe circuit consists of three identical CMOS inverters connected in a ring.\n*   The supply node (where $R_X$ is measured) is connected to the sources of the PMOS transistors in all three inverters.\n*   The inputs and outputs are connected in a feedback loop: Output of Inverter 1 $\\rightarrow$ Input of Inverter 2 $\\rightarrow$ Output of Inverter 2 $\\rightarrow$ Input of Inverter 3 $\\rightarrow$ Output of Inverter 3 $\\rightarrow$ Input of Inverter 1.\n*   We assume the inverters are biased at their metastable point (switching threshold), where both NMOS and PMOS transistors are in saturation. We assume symmetry: $g_{mn} = g_{mp} = g_m$ and $r_{on} = r_{op} = r_o$.\n\n**2. Small-Signal Model of a Single Inverter**\nLet $v_x$ be the small-signal voltage at the supply node.\nFor a single inverter stage with input $v_{in}$ and output $v_{out}$:\n*   The PMOS source is at $v_x$, gate at $v_{in}$, drain at $v_{out}$.\n*   The NMOS source is at ground (0), gate at $v_{in}$, drain at $v_{out}$.\n\nApplying Kirchhoff's Current Law (KCL) at the output node (assuming the load is the high-impedance gate of the next stage, so no current flows out):\nThe current flowing from the supply through the PMOS must equal the current flowing to ground through the NMOS.\n$$i_{PMOS} = i_{NMOS}$$\n$$g_m(v_x - v_{in}) + \\frac{v_x - v_{out}}{r_o} = g_m(v_{in} - 0) + \\frac{v_{out} - 0}{r_o}$$\n\nRearranging terms to group $v_{in}$ and $v_{out}$:\n$$g_m v_x + \\frac{v_x}{r_o} = 2g_m v_{in} + \\frac{2v_{out}}{r_o}$$\n$$v_x \\left(g_m + \\frac{1}{r_o}\\right) = 2 \\left( g_m v_{in} + \\frac{v_{out}}{r_o} \\right)$$\nLet $g_o = 1/r_o$. Then:\n$$g_m v_{in} + g_o v_{out} = \\frac{1}{2} v_x (g_m + g_o) \\quad \\text{--- (Equation 1)}$$\n\n**3. Current Drawn from Supply**\nThe small-signal current $i_{stage}$ drawn from the supply node by one inverter flows into the source of the PMOS transistor:\n$$i_{stage} = g_m(v_x - v_{in}) + g_o(v_x - v_{out})$$\n$$i_{stage} = v_x(g_m + g_o) - (g_m v_{in} + g_o v_{out})$$\n\nSubstituting Equation 1 into this expression:\n$$i_{stage} = v_x(g_m + g_o) - \\frac{1}{2} v_x (g_m + g_o)$$\n$$i_{stage} = \\frac{1}{2} v_x (g_m + g_o)$$\n\n**4. Total Resistance**\nSince there are three identical inverters connected in parallel to the supply node, the total current $i_x$ is:\n$$i_x = 3 \\times i_{stage} = \\frac{3}{2} v_x (g_m + g_o)$$\n\nThe small-signal resistance $R_X$ is the ratio of the test voltage to the total current:\n$$R_X = \\frac{v_x}{i_x} = \\frac{v_x}{\\frac{3}{2} v_x (g_m + g_o)} = \\frac{2}{3(g_m + g_o)}$$\n\nAssuming $g_m \\gg g_o$ (which is typical for MOS transistors), the resistance simplifies to:\n$$R_X \\approx \\frac{2}{3g_m}$$\n\n**Answer:**\nThe small-signal resistance seen looking into the supply node is **$\\frac{2}{3(g_m + g_o)}$** or approximately **$\\frac{2}{3g_m}$**, where $g_m$ and $g_o$ ($1/r_o$) are the transconductance and output conductance of the transistors in the inverters (assuming symmetric NMOS and PMOS devices).",
        "format": "markdown",
        "sha256": "eb63309839ac34c122ea5383843929ddfcbf08819d2088df2e3b87eaf5d3a050"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer derives a static gm-based resistance, approximately 2/(3gm), and ignores the oscillation-driven charging and discharging of the load capacitances that sets the supply resistance.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 13369,
        "total_tokens": 15898,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12307,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 13369,
        "total_tokens": 15898,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12307,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-005-determine-small-signal-resistance-seen-looking-into",
      "part": "part2",
      "question_number": 5,
      "question": "Determine the small-signal resistance seen looking into the supply node of the ring oscillator in the figure.",
      "figures": [
        "tasks/part2-005-determine-small-signal-resistance-seen-looking-into/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To determine the small-signal resistance $R_X$ seen looking into the supply node of the ring oscillator, we analyze the circuit at its DC operating point (the metastable equilibrium point) using a small-signal model.\n\n**1. Circuit Analysis and Operating Point**\nThe circuit is a 3-stage ring oscillator composed of inverters. For a CMOS ring oscillator, the unstable DC equilibrium point (where small-signal analysis is typically performed) occurs when the input and output of each inverter are at $V_{DD}/2$. At this point, both the NMOS and PMOS transistors in each inverter are in saturation.\n\n**2. Small-Signal Model**\nLet's model each inverter stage. The supply node is connected to the source of the PMOS transistor in each inverter. The ground node is connected to the source of the NMOS transistor.\n*   Let $g_m$ be the transconductance of the transistors (assuming symmetric inverters where $g_{mn} = g_{mp} = g_m$).\n*   Let $r_o$ be the output resistance of the transistors.\n\nWe apply a small test voltage $v_x$ at the supply node. We want to find the resulting current $i_x$ flowing into the node, such that $R_X = v_x / i_x$.\n\n**3. Common-Mode Response**\nSince the supply voltage $v_x$ is applied to all three stages simultaneously, this is a common-mode perturbation. Due to the symmetry of the ring oscillator, the voltages at the internal nodes (inputs and outputs of the inverters) will all change by the same amount, let's call it $v$.\nSo, $v_{in,1} = v_{in,2} = v_{in,3} = v_{out,1} = v_{out,2} = v_{out,3} = v$.\n\nFor a single inverter stage, the small-signal output voltage $v_{out}$ is related to the input $v_{in}$ and supply $v_x$ by:\n$$v_{out} \\approx \\frac{A_0 + 1}{2} v_x - A_0 v_{in}$$\nwhere $A_0 = g_m r_o$ is the intrinsic gain.\nSubstituting the common-mode condition $v_{out} = v_{in} = v$:\n$$v = \\frac{A_0 + 1}{2} v_x - A_0 v$$\n$$v(1 + A_0) = v_x \\frac{A_0 + 1}{2}$$\n$$v = \\frac{v_x}{2}$$\nThis means that for a small change $v_x$ in the supply, the internal node voltages change by $v_x/2$.\n\n**4. Calculating Current and Resistance**\nThe current $i_x$ drawn from the supply node flows into the sources of the three PMOS transistors.\nFor one PMOS transistor:\n*   Source voltage $v_s = v_x$\n*   Gate voltage $v_g = v = v_x/2$\n*   Drain voltage $v_d = v = v_x/2$\n\nThe small-signal current $i_p$ flowing into the source of the PMOS is:\n$$i_p = g_m (v_s - v_g) + \\frac{v_s - v_d}{r_o}$$\n$$i_p = g_m \\left(v_x - \\frac{v_x}{2}\\right) + \\frac{v_x - v_x/2}{r_o}$$\n$$i_p = g_m \\frac{v_x}{2} + \\frac{v_x}{2 r_o} = \\frac{v_x}{2} \\left(g_m + \\frac{1}{r_o}\\right)$$\n\nSince there are 3 identical inverters connected in parallel to the supply node, the total current $i_x$ is:\n$$i_x = 3 i_p = \\frac{3 v_x}{2} \\left(g_m + \\frac{1}{r_o}\\right)$$\n\nThe small-signal resistance $R_X$ is:\n$$R_X = \\frac{v_x}{i_x} = \\frac{2}{3 \\left(g_m + \\frac{1}{r_o}\\right)}$$\n\nAssuming $g_m \\gg 1/r_o$ (which is typical for MOS transistors, $g_m r_o \\gg 1$), the resistance simplifies to:\n$$R_X \\approx \\frac{2}{3 g_m}$$\n\n**Answer:**\nThe small-signal resistance seen looking into the supply node is approximately **$\\frac{2}{3g_m}$** (where $g_m$ is the transconductance of the PMOS transistor in each inverter). If considering the total transconductance of the inverter stage $G_m \\approx 2g_m$, it can be written as $\\frac{4}{3G_m}$. More precisely, it is $\\frac{2}{3(g_m + g_{ds})}$.",
        "format": "markdown",
        "sha256": "faa6a8acb47917593cf349581ee85f14daf338f40cd6fe46ac512e7463fe8dd4"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer analyzes only the static metastable operating point and concludes with the gm-based resistance 2/(3gm), missing the dominant oscillation-driven charging and discharging of the load capacitances.",
          "golden_solution_sha256": "567a4e1905413cda5af92a626cb359563db923ba665d1835ff2377a534cd5d21",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 12140,
        "total_tokens": 14669,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11037,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2529,
        "output_tokens": 12140,
        "total_tokens": 14669,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 11037,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the answer changes significantly.\n\nHere is the detailed explanation:\n\n1.  **Validity of the Formula (The Metastable Point):**\n    The formula $R_X \\approx \\frac{1}{3} (\\frac{1}{g_{mn}} + \\frac{1}{g_{mp}})$ is derived based on the assumption that each inverter is biased at its **metastable point** (the unstable DC equilibrium where $V_{in} = V_{out} \\approx V_{DD}/2$).\n    *   At this specific DC bias point, if you apply a small common-signal perturbation to the supply node, the symmetry of the ring forces the small-signal voltages at the inputs and outputs to be equal ($v_{in} = v_{out}$).\n    *   Under this condition ($v_{in} = v_{out}$), the MOS transistors effectively act as **diode-connected** devices. The small-signal resistance of a diode-connected MOS is $1/g_m$.\n    *   Since the PMOS and NMOS are in series between supply and ground, the resistance of one branch is $1/g_{mp} + 1/g_{mn}$.\n    *   With three inverters in parallel, the total resistance is indeed $\\frac{1}{3} (1/g_{mn} + 1/g_{mp})$.\n\n2.  **During Oscillation (Large-Signal Regime):**\n    When the circuit oscillates, it is no longer at the metastable DC point. The voltages are swinging rail-to-rail (large signals).\n    *   **Transistors Switching:** The transistors are constantly switching between cutoff (off) and triode/linear (on) regions. They are not sitting in saturation where the small-signal parameter $g_m$ is defined and constant.\n    *   **Phase Shift:** The condition $V_{in} = V_{out}$ is no longer true. In a 3-stage ring oscillator, the outputs are $120^\\circ$ out of phase with each other. The input of one inverter is the output of the previous one, so the \"diode-connected\" assumption ($v_{in} = v_{out}$ for the same inverter) is invalid.\n    *   **Effective Impedance:** The impedance seen looking into the supply node during oscillation is dominated by the **dynamic current** required to charge and discharge the load capacitances of the inverters. The effective resistance would be closer to $R_{eff} \\approx \\frac{V_{DD}}{I_{avg}}$, where $I_{avg} \\approx 3 \\cdot C_L V_{DD} f_{osc}$ (plus short-circuit current). This is fundamentally different from the small-signal $1/g_m$ resistance.\n\n**Conclusion:**\nThe computed value $R_X$ represents the small-signal impedance at the **unstable startup bias point**. Once the circuit oscillates, the operating point changes dynamically, the \"diode-connected\" assumption fails, and the effective resistance seen by the supply changes completely.",
        "format": "markdown",
        "sha256": "d54f83724ee80c591455394d7b02e19e523a82514e55a305a9b528106bb9b5ee"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies capacitive charging and discharging as the oscillating supply-current mechanism and gives RX ≈ 1/(3 CL fosc). But it claims the resistance changes significantly without comparing this result to the static estimate; the key conclusion is that RX remains on the order of the MOS on-resistance, not much higher.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2613,
        "output_tokens": 8194,
        "total_tokens": 10807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7530,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2613,
        "output_tokens": 8194,
        "total_tokens": 10807,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7530,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the answer changes.\n\nHere is the detailed reasoning:\n\n1.  **Validity of the Formula:** The formula $R_X \\approx \\frac{1}{3} (\\frac{1}{g_{mn}} + \\frac{1}{g_{mp}})$ is derived based on a **small-signal linearization around the metastable DC operating point**.\n    *   At this specific DC bias point (where $V_{in} = V_{out} \\approx V_{DD}/2$ for all inverters), the circuit is in equilibrium (though unstable).\n    *   Due to symmetry, a small perturbation at the supply node $V_{DD}$ affects all three stages equally. This maintains the condition $v_{in} \\approx v_{out}$ for the small-signal variations.\n    *   When $v_{in} = v_{out}$, a CMOS inverter effectively behaves like a diode-connected NMOS in series with a diode-connected PMOS. The resistance of this branch is $r_{on} + r_{op} \\approx \\frac{1}{g_{mn}} + \\frac{1}{g_{mp}}$.\n    *   Since there are three such branches in parallel (one for each inverter), the total resistance is divided by 3.\n\n2.  **Why it Changes During Oscillation:**\n    *   **Large-Signal Behavior:** Oscillation is a large-signal phenomenon. The voltages at the nodes swing rail-to-rail (from 0 to $V_{DD}$). The transistors are not biased in the saturation region with constant transconductances $g_{mn}$ and $g_{mp}$. Instead, they switch between cutoff, saturation, and triode (linear) regions. Therefore, the parameters $g_{mn}$ and $g_{mp}$ in the formula are no longer constant or representative of the device state.\n    *   **Loss of \"Diode-Connected\" Condition:** The derivation relies on the inverter input being equal to its output ($V_{in} = V_{out}$). In a ring oscillator, the input of one stage is the output of the previous stage. For oscillation to occur, there must be a phase shift around the loop (specifically, a total phase shift of $360^\\circ$, which implies $180^\\circ$ from the inversion and $180^\\circ$ from the delay of the 3 stages). Consequently, $V_{in} \\neq V_{out}$; they are significantly different signals (phase-shifted and large-swing). The inverters do not behave as diode-connected devices.\n    *   **Time-Varying Impedance:** During oscillation, the resistance seen looking into the supply node becomes time-varying. For example, when the PMOS devices are fully on (inputs low), the resistance is very low (dominated by the on-resistance $R_{on}$ in the triode region). When PMOS devices are off, the resistance is very high.\n\nIn summary, the formula applies only to the unstable equilibrium point. Once the circuit oscillates, the operating conditions change drastically, and the small-signal resistance is no longer described by that static equation. An \"effective\" resistance during oscillation is better described by the dynamic power consumption $P = C_{load} V_{DD}^2 f$, leading to an effective resistance $R_{eff} \\approx \\frac{V_{DD}}{I_{avg}} = \\frac{1}{3 C_{load} f}$ (roughly), which is fundamentally different.",
        "format": "markdown",
        "sha256": "3dca5417dec3d0ca8a6757d06f8073235608d4c4df628d3c67737f6a808105ac"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It identifies the oscillatory capacitive-current mechanism and gives the equivalent result RX ≈ 1/(3 Cload f), but does not show that this remains on the order of the MOS on-resistance or inverse transconductance. Its claim that the effective resistance is fundamentally different leaves the key magnitude comparison unresolved.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 2304,
        "input_tokens": 2613,
        "output_tokens": 9312,
        "total_tokens": 11925,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8548,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 2304,
        "input_tokens": 2613,
        "output_tokens": 9312,
        "total_tokens": 11925,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8548,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-006-oscillates-change",
      "part": "part2",
      "question_number": 6,
      "question": "For the ring oscillator in the figure, somebody computes the small-signal resistance `RX`\nseen looking into the supply node as\n\n```text\nRX ~= (1/3) (1/gmn + 1/gmp)\n```\n\nwhere `gmn` and `gmp` are the transconductances of the NMOS and PMOS devices in each\ninverter, because each inverter behaves as two diode-connected devices in series.\n\nIf the circuit oscillates, does this answer change?",
      "figures": [
        "tasks/part2-006-oscillates-change/figure-08.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "**Yes, the answer changes.**\n\nHere is the detailed explanation of why:\n\n1.  **Validity of the Formula (The Metastable Point):**\n    The formula $R_X \\approx \\frac{1}{3} (\\frac{1}{g_{mn}} + \\frac{1}{g_{mp}})$ is derived by assuming the inverters are biased at their **metastable DC operating point**.\n    *   In a ring oscillator, the unstable equilibrium occurs when the input voltage equals the output voltage for all stages ($V_{in} = V_{out} \\approx V_{DD}/2$).\n    *   At this specific bias point, for each inverter, the gate is connected to the drain (since $V_{in} = V_{out}$).\n    *   This configuration makes both the NMOS and PMOS transistors effectively **diode-connected** (operating in saturation with $V_{GS} = V_{DS}$).\n    *   The small-signal resistance of a diode-connected transistor is approximately $1/g_m$. Since the PMOS and NMOS are in series from supply to ground, the resistance of one inverter is $1/g_{mp} + 1/g_{mn}$.\n    *   With three inverters in parallel connected to the supply node, the total resistance is divided by 3.\n\n2.  **During Oscillation (Large-Signal Regime):**\n    *   When the circuit oscillates, it is no longer sitting at the metastable DC point. The voltages are swinging rail-to-rail (large-signal operation).\n    *   The transistors are constantly switching between **cutoff** (OFF) and **triode/linear** (ON) regions. They are not permanently in the saturation region where the $g_m$ parameter used in the formula is defined.\n    *   Consequently, the instantaneous resistance looking into the supply node becomes **time-varying**. At any given moment, some transistors are OFF (infinite resistance) and some are ON (low resistance, $R_{on}$).\n\n3.  **Effective Resistance:**\n    If you are looking for an equivalent resistance during oscillation (e.g., for power supply noise analysis), it is better modeled by the effective resistance related to dynamic power consumption:\n    $$R_{eff} \\approx \\frac{V_{DD}}{I_{avg}} = \\frac{V_{DD}^2}{P_{dynamic}}$$\n    where $P_{dynamic} \\approx 3 \\cdot C_{load} \\cdot V_{DD}^2 \\cdot f_{osc}$. This value is generally different from the small-signal resistance calculated at the switching threshold.\n\n**Summary:** The formula provided is only correct for the small-signal impedance at the unstable DC equilibrium point. Once the circuit starts oscillating, the operating point changes dynamically, and the simple resistive model based on $g_m$ at the threshold is no longer valid.",
        "format": "markdown",
        "sha256": "4218b0cf78e59e021a88607c503d1b567deae09396b9c8f6614f4de52785f61d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It identifies the dynamic capacitive-power mechanism, which implies an effective resistance of about 1/(3 fosc Cload), but it does not compare that resistance with the static estimate or show that it remains on the order of the MOS on-resistance. Saying it is generally different leaves the key conclusion unresolved.",
          "golden_solution_sha256": "41b3aba626dbabae7c16266607298d97003b7365b7c8eebf62086ccaef8b74fa",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 2304,
        "input_tokens": 2613,
        "output_tokens": 5167,
        "total_tokens": 7780,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4531,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 2304,
        "input_tokens": 2613,
        "output_tokens": 5167,
        "total_tokens": 7780,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4531,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a dynamic comparator or latch (specifically, a variation of a StrongARM latch or a dynamic regenerative latch).\n\n1.  **Identify the role of M7:** Transistor $M_7$ acts as the tail switch (or current source) for the input differential pair ($M_1$ and $M_2$). It is controlled by the clock signal $CK$. When $CK$ is high, $M_7$ turns on, connecting the common source node of $M_1$ and $M_2$ to ground.\n\n2.  **Effect of increasing width ($W_7$):** Increasing the width of a MOSFET decreases its on-resistance ($R_{on}$). Therefore, as the width of $M_7$ increases, it becomes a better switch with lower resistance to ground.\n\n3.  **Impact on Input Pair ($M_1, M_2$):**\n    *   With a lower resistance at the tail ($M_7$), the voltage at the common source node of $M_1$ and $M_2$ (let's call it $V_S$) will be closer to ground (0 V).\n    *   This increases the gate-source voltage ($V_{GS} = V_{in} - V_S$) of the input transistors $M_1$ and $M_2$ (assuming $V_{in}$ is fixed).\n    *   A higher $V_{GS}$ leads to a higher drain current ($I_D$) and, crucially, a higher transconductance ($g_m$) for the input pair. The transconductance $g_m$ is proportional to $\\sqrt{I_D}$ (in saturation) or directly related to the overdrive voltage.\n\n4.  **Impact on Voltage Gain:**\n    *   The \"initial voltage gain\" of this circuit refers to the amplification provided by the input stage before the regenerative latch (cross-coupled pairs $M_3/M_4$ and $M_5/M_6$) fully takes over.\n    *   The small-signal voltage gain is generally proportional to the transconductance of the input pair ($g_{m1,2}$) multiplied by the load impedance.\n    *   Since increasing the width of $M_7$ increases the transconductance $g_{m1,2}$ (by allowing more current to flow and increasing the overdrive voltage), the initial voltage gain increases.\n\n**Answer:** The initial voltage gain **increases**.",
        "format": "markdown",
        "sha256": "306f1b6633ec0c5b1b334f40f746531c311de62c5fe6b5a14d22c501268a86ce"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer gives the opposite trend: widening M7 increases tail current and lowers the initial gain because the gain factor scales roughly as gm/ICM, with gm growing more slowly than current. It correctly identifies M7 as the tail device, but its on-resistance argument misses the dominant mechanism.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 16088,
        "total_tokens": 18603,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15547,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 16088,
        "total_tokens": 18603,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15547,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the step-by-step explanation of what happens to the initial voltage gain as the width of transistor $M_7$ increases:\n\n1.  **Identify the Role of M7:** Transistor $M_7$ acts as a tail switch (or current source switch) for the input differential pair formed by $M_1$ and $M_2$. It is controlled by the clock signal $CK$. When $CK$ is high, $M_7$ turns on, connecting the common source node of $M_1$ and $M_2$ to ground.\n\n2.  **Effect of Increasing Width on Resistance:** The on-resistance ($R_{on}$) of a MOSFET acting as a switch is inversely proportional to its width ($W$). Therefore, as the width of $M_7$ increases, its on-resistance decreases ($R_{on7} \\downarrow$).\n\n3.  **Effect on Tail Node Voltage:** During the evaluation phase (when $CK$ is high), current flows from the nodes $P$ and $Q$ through $M_1$ and $M_2$ into the tail node and then through $M_7$ to ground. The voltage at the common source node (tail node) is approximately $V_{tail} \\approx I_{total} \\times R_{on7}$. Since $R_{on7}$ decreases, the voltage at the tail node decreases (it gets closer to ground potential).\n\n4.  **Effect on Input Transistors ($M_1, M_2$):** The gate-source voltage ($V_{GS}$) of the input transistors $M_1$ and $M_2$ is given by $V_{GS} = V_{in} - V_{tail}$. As $V_{tail}$ decreases, the effective $V_{GS}$ for $M_1$ and $M_2$ increases.\n\n5.  **Effect on Transconductance ($g_m$):** The transconductance ($g_m$) of a MOSFET is directly related to its overdrive voltage ($V_{GS} - V_{TH}$) and bias current. An increase in $V_{GS}$ leads to an increase in the drain current and consequently an increase in the transconductance $g_{m1,2}$ of the input pair.\n\n6.  **Effect on Voltage Gain:** The initial voltage gain of the differential stage is proportional to the transconductance of the input pair ($A_v \\approx g_{m1,2} \\times R_{load}$). Since $g_{m1,2}$ increases, the initial voltage gain increases.\n\n**Conclusion:**\nAs the width of $M_7$ increases, the initial voltage gain **increases**. This is because a wider $M_7$ provides a lower resistance path to ground, which increases the effective gate-source voltage and transconductance of the input differential pair ($M_1, M_2$).",
        "format": "markdown",
        "sha256": "35bebdc1103056d38a92e3ea3d6f8b70461400be25651c3cc566d60dc39f3ec6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer reaches the opposite trend: widening M7 increases tail current and decreases the initial gain, rather than increasing it. It correctly recognizes M7 as the tail device, but treats it as a simple resistor and misses the dominant current and gm/ICM effect.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 7605,
        "total_tokens": 10120,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6967,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 7605,
        "total_tokens": 10120,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6967,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-007-initial-voltage-gain-as-width-m7-increases",
      "part": "part2",
      "question_number": 7,
      "question": "In the circuit shown in the figure, what happens to the initial voltage gain as the width of M7 increases?",
      "figures": [
        "tasks/part2-007-initial-voltage-gain-as-width-m7-increases/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a dynamic latch comparator (specifically, a variation of a StrongARM latch or a clocked regenerative comparator).\n\n1.  **Identify the role of M7:** Transistor $M_7$ acts as the tail switch for the input differential pair formed by $M_1$ and $M_2$. It is controlled by the clock signal $CK$. When $CK$ is high, $M_7$ turns on, connecting the common source of $M_1$ and $M_2$ to ground, enabling the evaluation phase.\n\n2.  **Analyze the effect of Width ($W$) on Resistance:** The on-resistance ($R_{on}$) of a MOSFET in the triode region (which acts as a switch) is inversely proportional to its width ($W$). Therefore, as the width of $M_7$ increases, its on-resistance decreases ($R_{on7} \\downarrow$).\n\n3.  **Impact on Input Pair ($M_1, M_2$):**\n    *   During the evaluation phase, current flows from nodes $P$ and $Q$ through $M_1$ and $M_2$ and then through $M_7$ to ground.\n    *   The voltage at the common source node of $M_1$ and $M_2$ (let's call it $V_S$) is determined by the current flowing through $M_7$ and its resistance: $V_S \\approx I_{total} \\times R_{on7}$.\n    *   If $R_{on7}$ is large (small $W_7$), $V_S$ will be higher, which reduces the effective gate-source voltage ($V_{GS} = V_{in} - V_S$) of the input transistors $M_1$ and $M_2$.\n    *   As $W_7$ increases, $R_{on7}$ decreases, causing $V_S$ to drop closer to ground (0 V). This increases the effective $V_{GS}$ for $M_1$ and $M_2$.\n\n4.  **Impact on Transconductance and Gain:**\n    *   A higher $V_{GS}$ for $M_1$ and $M_2$ increases their drain current and, crucially, their transconductance ($g_m$).\n    *   The initial voltage gain of the comparator stage is proportional to the transconductance of the input pair ($g_{m1,2}$). Specifically, the input voltage difference is converted into a current difference $\\Delta I = g_m \\Delta V_{in}$. This current difference discharges the nodes $P$ and $Q$ at different rates, creating the initial voltage difference that triggers the regenerative latch.\n    *   Since increasing $W_7$ leads to a higher $g_m$ for the input pair, the circuit can generate a larger differential signal for the same input voltage difference.\n\n**Conclusion:**\nAs the width of $M_7$ increases, its on-resistance decreases, which improves the biasing of the input differential pair ($M_1, M_2$) by lowering the common-source voltage. This increases the transconductance of the input stage, thereby **increasing** the initial voltage gain.",
        "format": "markdown",
        "sha256": "4120c86b1f32eb8d281fd64b19144ab791a5aa0e129e4e79ccad1ba148dff5d6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly identifies M7 as the tail device, but reaches the opposite trend. A wider M7 increases tail current, and the initial gain decreases; the on-resistance/source-voltage argument misses this dominant effect.",
          "golden_solution_sha256": "3be19d840ea0028f994c70cfd93497080016f88968540a82c98a00f03980212f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 10266,
        "total_tokens": 12781,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9557,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 10266,
        "total_tokens": 12781,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9557,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, which represents a dynamic comparator (specifically a StrongARM latch topology), here is the analysis:\n\n1.  **Circuit Operation**: The circuit consists of an input differential pair ($M_1, M_2$) and a cross-coupled latch ($M_3, M_4$). During the evaluation phase (when the clock $CK$ enables the tail transistor $M_7$), the input voltages $V_{in1}$ and $V_{in2}$ control the current flowing through $M_1$ and $M_2$. This current discharges the capacitance at nodes **P** and **Q**.\n\n2.  **Voltage Development at P and Q**: The voltage difference developed between nodes P and Q is determined by the difference in discharge currents and the capacitance at these nodes.\n    $$ \\Delta V_{PQ} = V_P - V_Q \\approx \\frac{(I_{D1} - I_{D2})}{C_{PQ}} \\cdot t $$\n    Since the current difference is proportional to the input voltage difference ($I_{D1} - I_{D2} = g_m \\cdot \\Delta V_{in}$), we can write:\n    $$ \\Delta V_{PQ} \\approx \\frac{g_m \\cdot \\Delta V_{in}}{C_{PQ}} \\cdot t $$\n\n3.  **Effect of Capacitance**: The \"initial voltage gain\" can be thought of as the ratio of the developed voltage difference at the internal nodes (P, Q) to the input voltage difference ($\\Delta V_{in}$) during the initial phase of operation. From the equation above, this gain is proportional to $\\frac{1}{C_{PQ}}$.\n\n4.  **Conclusion**: If you **increase the capacitance** at nodes P and Q, the rate at which the voltage difference develops decreases. Consequently, for a given input and time, the voltage swing at these nodes will be smaller. This reduces the driving signal for the subsequent regenerative latch stage ($M_3, M_4$).\n\nTherefore, the initial voltage gain **decreases**.",
        "format": "markdown",
        "sha256": "46c8a92d1006af0d6e373916c5f9205ecb9b47b5b8682f53bdaba8057507fcbe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The inverse-capacitance slope is correct at a fixed time, but the answer misses that the amplification phase lasts proportionally longer as capacitance increases, so the initial gain remains approximately unchanged. Its central conclusion is wrong.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 7569,
        "total_tokens": 10084,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7108,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 7569,
        "total_tokens": 10084,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7108,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the step-by-step reasoning:\n\n1.  **Identify the Circuit:** The figure shows a dynamic latch comparator, specifically a topology similar to the **StrongARM latch**. It consists of an input differential pair ($M_1, M_2$), a tail switch ($M_7$), and a regenerative latch formed by cross-coupled transistors ($M_3, M_4$ and $M_5, M_6$).\n\n2.  **Understand the Operation:**\n    *   **Reset Phase:** When $CK$ is low, the switches $S_1-S_4$ are ON, precharging nodes $X, Y, P,$ and $Q$ to $V_{DD}$. $M_7$ is OFF.\n    *   **Evaluation Phase:** When $CK$ goes high, $M_7$ turns ON and the switches turn OFF. The input differential pair ($M_1, M_2$) begins to discharge nodes $P$ and $Q$ towards ground. The rate of discharge depends on the input voltages $V_{in1}$ and $V_{in2}$.\n\n3.  **Analyze Initial Voltage Gain:**\n    *   The \"initial voltage gain\" refers to the gain of the circuit during the early part of the evaluation phase, before the positive feedback (regeneration) of the cross-coupled pairs fully takes over.\n    *   During this initial phase, the input transistors $M_1$ and $M_2$ act as transconductors, converting the input voltage difference ($\\Delta V_{in}$) into a current difference ($\\Delta I = g_m \\cdot \\Delta V_{in}$).\n    *   This current flows into the capacitance at nodes $P$ and $Q$ (let's call it $C_{P,Q}$).\n    *   The voltage change at these nodes is given by $\\Delta V = \\frac{1}{C} \\int I \\, dt$. For a short initial time $\\Delta t$, the voltage difference developed between nodes $P$ and $Q$ is approximately $\\Delta V_{PQ} \\approx \\frac{\\Delta I \\cdot \\Delta t}{C_{P,Q}}$.\n    *   Substituting the current expression: $\\Delta V_{PQ} \\approx \\frac{g_m \\cdot \\Delta V_{in} \\cdot \\Delta t}{C_{P,Q}}$.\n    *   The initial voltage gain $A_v$ can be approximated as the ratio $\\frac{\\Delta V_{PQ}}{\\Delta V_{in}} \\approx \\frac{g_m \\cdot \\Delta t}{C_{P,Q}}$.\n\n4.  **Effect of Increasing Capacitance:**\n    *   From the relationship derived above ($A_v \\propto \\frac{1}{C_{P,Q}}$), it is clear that the voltage gain is inversely proportional to the capacitance at nodes $P$ and $Q$.\n    *   Increasing the capacitance $C_{P,Q}$ increases the total load at the drains of the input pair. This means it takes more charge (and thus more time) to change the voltage at these nodes.\n    *   Consequently, for a given input signal and time interval, the voltage swing at nodes $P$ and $Q$ will be smaller.\n\n**Conclusion:**\nIf we increase the capacitance at nodes P and Q, the **initial voltage gain decreases**. The larger capacitance slows down the voltage discharge at these nodes, resulting in a smaller voltage difference developed for a given input difference.",
        "format": "markdown",
        "sha256": "730758708395bdb7675b5b77ff861b8588cd75484f4486c4e315fe8b8ce1a9d1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The conclusion is wrong: the initial gain remains essentially unchanged. The answer considers voltage developed over a fixed time, but the larger capacitance also lengthens the amplification phase proportionally, canceling the reduced voltage slope. It correctly notes that capacitance slows the transient, but misses the defining gain result.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 5888,
        "total_tokens": 8403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 5888,
        "total_tokens": 8403,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5113,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-008-initial-voltage-gain-increase-capacitance-at-nodes",
      "part": "part2",
      "question_number": 8,
      "question": "In the figure, what happens to the initial voltage gain if we increase the capacitance at nodes P and Q?",
      "figures": [
        "tasks/part2-008-initial-voltage-gain-increase-capacitance-at-nodes/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the step-by-step reasoning:\n\n1.  **Identify the Circuit:** The figure shows a dynamic comparator, specifically a topology similar to the **StrongARM latch**. It consists of an input differential pair ($M_1, M_2$), a tail switch ($M_7$), and a regenerative latch formed by cross-coupled transistors ($M_3, M_4$ and $M_5, M_6$).\n\n2.  **Analyze the Operation at Nodes P and Q:**\n    *   During the evaluation phase (when $CK$ is high), the tail transistor $M_7$ turns on, and the input transistors $M_1$ and $M_2$ conduct current based on the input voltages $V_{in1}$ and $V_{in2}$.\n    *   Nodes P and Q are initially precharged (likely to $V_{DD}$ via switches $S_1, S_2$). When evaluation starts, the currents from $M_1$ and $M_2$ discharge the capacitance at nodes P and Q.\n    *   The voltage at these nodes drops at a rate determined by the current and the capacitance: $\\frac{dV}{dt} = \\frac{I}{C}$.\n\n3.  **Determine the Initial Voltage Gain:**\n    *   The \"initial voltage gain\" refers to the amplification of the input voltage difference ($V_{in1} - V_{in2}$) into a voltage difference at the internal nodes ($\\Delta V_{PQ} = V_P - V_Q$) before the strong regenerative feedback (latching) takes over.\n    *   The differential current generated by the input pair is $\\Delta I = g_m (V_{in1} - V_{in2})$, where $g_m$ is the transconductance of $M_1$ and $M_2$.\n    *   This current difference discharges the capacitances $C_P$ and $C_Q$ at nodes P and Q. The resulting voltage difference develops over time $t$ as:\n        $$ \\Delta V_{PQ}(t) \\approx \\frac{\\Delta I}{C} \\cdot t = \\frac{g_m (V_{in1} - V_{in2})}{C} \\cdot t $$\n    *   The effective initial voltage gain $A_v$ at a given time $t$ is the ratio of the developed voltage difference to the input voltage difference:\n        $$ A_v = \\frac{\\Delta V_{PQ}}{V_{in1} - V_{in2}} \\approx \\frac{g_m \\cdot t}{C} $$\n\n4.  **Effect of Increasing Capacitance:**\n    *   From the equation above, the initial voltage gain is inversely proportional to the capacitance $C$ at nodes P and Q.\n    *   If you **increase the capacitance** at nodes P and Q, the denominator increases.\n    *   This means the nodes will discharge more slowly, resulting in a smaller voltage difference $\\Delta V_{PQ}$ for the same input difference and time duration.\n\n**Conclusion:**\nIf we increase the capacitance at nodes P and Q, the **initial voltage gain decreases**. This is because the larger capacitance slows down the rate at which the voltage difference is developed at these intermediate nodes, reducing the signal amplitude passed to the subsequent regenerative stage.",
        "format": "markdown",
        "sha256": "73ecdb625c1a74f5bc835b11af29bda8fb459cd35855d03f80dc00346cb80e21"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer correctly notes that larger capacitance reduces the voltage slew rate at a fixed time, but it misses that the amplification phase lasts proportionally longer before regeneration. These effects cancel, so the initial gain is approximately unchanged, not decreased.",
          "golden_solution_sha256": "181f6e0ce2e77c4df0e1602f9ce1b8891080eeecdff293462f41c7d6d66c5590",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 5938,
        "total_tokens": 8453,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5194,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2515,
        "output_tokens": 5938,
        "total_tokens": 8453,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5194,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a dynamic latch (or a clocked comparator/sense amplifier). To determine the effect of increasing the widths of transistors $M_5$ and $M_6$, we need to analyze their role and the parasitic effects.\n\n1.  **Role of M5 and M6:** $M_5$ and $M_6$ form a cross-coupled PMOS pair. They act as the pull-up devices for the latch. During the regeneration phase, they help pull the output nodes ($X$ and $Y$, which are $V_{out}$) to $V_{DD}$. Specifically, if node $X$ drops, $M_6$ turns on and pulls node $Y$ up.\n\n2.  **Capacitance Effect:** Increasing the width ($W$) of MOS transistors increases their gate and drain parasitic capacitances. Since the gates and drains of $M_5$ and $M_6$ are connected to nodes $X$ and $Y$ (the output nodes), increasing their widths significantly increases the total capacitance at these nodes ($C_X$ and $C_Y$).\n\n3.  **Impact on Speed:**\n    *   **Precharge Phase:** When $CK$ is low, switches $S_3$ and $S_4$ (and potentially others) precharge nodes $X$ and $Y$ to $V_{DD}$. A larger capacitance at these nodes means it takes longer to charge them, increasing the precharge time.\n    *   **Evaluation/Regeneration Phase:** When the latch evaluates, the NMOS transistors $M_3$ and $M_4$ (driven by the input pair $M_1, M_2$) attempt to pull nodes $X$ and $Y$ down. The larger capacitance from wider $M_5$ and $M_6$ makes it harder and slower for $M_3$ and $M_4$ to discharge these nodes.\n    *   **Fighting Effect:** During the initial stage of evaluation, as the voltages at $X$ and $Y$ start to drop, the PMOS transistors $M_5$ and $M_6$ begin to turn on (since their source is at $V_{DD}$ and their gates are at the dropping nodes). They try to pull the nodes back up, fighting the discharge action of $M_3$ and $M_4$. Larger $M_5$ and $M_6$ transistors will fight more strongly, further slowing down the initial voltage divergence required to trigger the positive feedback regeneration.\n\nAlthough larger transistors have higher transconductance ($g_m$) which can theoretically speed up the final regeneration step ($\\tau \\approx C/g_m$), the increase in capacitance ($C$) is proportional. The dominant effect in such dynamic circuits is usually the increased capacitive load on the internal nodes, which slows down the voltage transitions.\n\nTherefore, the speed **degrades**.\n\n**Answer:** The speed degrades. Increasing the widths of $M_5$ and $M_6$ increases the parasitic capacitance at nodes $X$ and $Y$ (the output nodes). This larger capacitance takes longer to charge during the precharge phase and longer to discharge during the evaluation phase, thereby increasing the overall delay and reducing the speed of the circuit. Additionally, larger PMOS devices will more strongly oppose the initial discharge of the nodes by the NMOS pair ($M_3, M_4$).",
        "format": "markdown",
        "sha256": "dc34a3bc0555cf96499bbe546bff95562c306da0396c020e49bfba865fc5377e"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It identifies the cross-coupled PMOS devices and the real capacitance cost of widening them, but concludes that speed degrades. The initial effect is faster regeneration because increased pull-up strength dominates the added capacitance; capacitance limits the benefit only at larger widths.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 15435,
        "total_tokens": 17949,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14682,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 15435,
        "total_tokens": 17949,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 14682,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the step-by-step evaluation:\n\n1.  **Identify the Circuit:** The figure shows a dynamic latch (often used as a sense amplifier or a high-speed comparator). It consists of an input differential pair ($M_1, M_2$), a tail switch ($M_7$), a cross-coupled NMOS pair ($M_3, M_4$), and a cross-coupled PMOS pair ($M_5, M_6$). The transistors $S_1-S_4$ are used for precharging.\n\n2.  **Identify the Role of M5 and M6:** Transistors $M_5$ and $M_6$ form the PMOS part of the regenerative latch (cross-coupled pair). Their function is to provide positive feedback and pull the output nodes ($X$ and $Y$, which form $V_{out}$) up to $V_{DD}$ during the regeneration phase.\n\n3.  **Analyze the Effect of Increasing Width ($W$):**\n    *   **Transconductance ($g_m$):** Increasing the width of $M_5$ and $M_6$ increases their transconductance ($g_{m5,6}$). The speed of the regeneration phase is determined by the time constant $\\tau \\approx \\frac{C_L}{g_{m3,4} + g_{m5,6}}$, where $C_L$ is the total capacitance at the output nodes.\n    *   **Regeneration Speed:** A higher total transconductance ($g_{m3,4} + g_{m5,6}$) in the denominator reduces the time constant $\\tau$. This means the latch will regenerate (switch states) faster. Since PMOS transistors typically have lower mobility than NMOS transistors ($\\mu_p < \\mu_n$), the PMOS pair ($M_5, M_6$) is often the weaker link in the regeneration process. Strengthening them by increasing their width helps balance the rise and fall times and speeds up the overall decision process.\n    *   **Capacitance Trade-off:** While increasing the width also increases the parasitic capacitance at nodes $X$ and $Y$ (which would tend to slow things down), the increase in drive strength ($g_m$) usually dominates, especially if there is a significant load capacitance at the output. In the context of latch design, increasing the size of the cross-coupled pair is a standard method to improve regeneration speed.\n\n**Conclusion:**\nIncreasing the widths of M5 and M6 increases the transconductance of the PMOS regenerative pair. This strengthens the positive feedback loop, reduces the regeneration time constant, and allows the output to switch faster. Therefore, the **speed improves**.\n\n(Note: There is a limit; if the widths are increased too much, the added parasitic capacitance and the longer precharge time required for the larger nodes could eventually degrade the maximum clock frequency, but the primary effect on the latch regeneration speed is an improvement.)",
        "format": "markdown",
        "sha256": "d3119f3dda4f0220a18e28ecadeafa0f209ee7e5aa6c6a77a2ddcfa05a9cda1d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies M5/M6 as the cross-coupled PMOS regenerative devices, says widening initially improves speed by strengthening regeneration, and notes that added parasitic capacitance eventually limits the benefit. The approximate time-constant discussion is not exact but does not undermine the essential conclusion.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 10680,
        "total_tokens": 13194,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10026,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 10680,
        "total_tokens": 13194,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10026,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-009-increase-widths-m5-and-m6-speed-improve",
      "part": "part2",
      "question_number": 9,
      "question": "If we increase the widths of M5 and M6 in the figure, does the speed improve or degrade?",
      "figures": [
        "tasks/part2-009-increase-widths-m5-and-m6-speed-improve/figure-09.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the answer:\n\n**The speed degrades.**\n\n**Reasoning:**\n1.  **Increased Parasitic Capacitance:** Transistors M5 and M6 are connected to the critical high-impedance nodes X and Y (which are the output nodes $V_{out}$). Increasing their widths ($W$) significantly increases the parasitic capacitance at these nodes (drain-to-bulk capacitance) and the gate capacitance loading the opposite nodes (since the gates are cross-coupled).\n2.  **Precharge Time:** During the precharge phase (when CK is low), the switches $S_3$ and $S_4$ (and potentially others) must charge nodes X and Y to $V_{DD}$. A larger capacitance at these nodes increases the RC time constant for charging, thereby increasing the precharge time and limiting the maximum clock frequency.\n3.  **Regeneration Time Constant:** The speed of the latch during the evaluation phase is determined by the regeneration time constant $\\tau \\approx C_{total} / (g_{m,n} + g_{m,p})$. While increasing the width of M5 and M6 increases their transconductance ($g_{m,p}$), it also increases the total capacitance ($C_{total}$) proportionally. Since the mobility of holes (PMOS) is lower than that of electrons (NMOS), the ratio $g_m/C$ for the PMOS devices is generally lower than for the NMOS devices. Therefore, adding more PMOS capacitance tends to increase the overall time constant or, at best, offers diminishing returns while definitely slowing down the precharge phase.\n\nIn summary, the increased capacitive load on the internal nodes outweighs the benefit of increased drive strength, leading to a degradation in speed.",
        "format": "markdown",
        "sha256": "784703ba2cfc8190f6a19b7fe5525246b60b4b37aae1cbe6dddc2a7e8c8eaa1a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer recognizes that wider M5/M6 add capacitance and increase transconductance, but reaches the opposite initial speed trend. The regenerative-strength benefit initially dominates; added capacitance limits improvement only at larger widths.",
          "golden_solution_sha256": "5eed0194a609e5504312082df6fe7d71e18f6abfa8d0ff1bc1936ac8f33e2388",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 9528,
        "total_tokens": 12042,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9143,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2514,
        "output_tokens": 9528,
        "total_tokens": 12042,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9143,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "The circuit shown is a dynamic logic circuit, specifically resembling a **TSPC (True Single Phase Clock)** latch or flip-flop structure, configured in a feedback loop (likely a divide-by-2 counter or ring oscillator element).\n\nTo determine the effect of increasing the widths of the clocked transistors (the transistors with gates connected to $CK$ and $\\overline{CK}$), we need to consider the trade-offs between resistance and capacitance:\n\n1.  **Resistance ($R$):** Increasing the width ($W$) of a transistor decreases its on-resistance ($R_{on} \\propto 1/W$). Since the clocked transistors are in series with the logic transistors (the top PMOS controlled by $Z$/$X$ and the bottom NMOS $M_1$), reducing their resistance would theoretically speed up the charging and discharging of nodes $X$ and $Y$.\n\n2.  **Capacitance ($C$):** Increasing the width of a transistor increases its parasitic capacitances (gate capacitance $C_g$, drain capacitance $C_d$, source capacitance $C_s$).\n    *   **Clock Load:** The gate capacitance of the clocked transistors is connected directly to the clock signals ($CK$ and $\\overline{CK}$). Increasing the width significantly increases the load on the clock distribution network. This can slow down the clock edges (increase rise/fall times), which degrades the overall circuit speed and can cause timing issues.\n    *   **Node Capacitance:** The drain/source capacitances of the clocked transistors are connected to the internal nodes (between the series transistors) and the output nodes ($X$ and $Y$).\n        *   The internal node capacitance must be charged/discharged through the logic transistors (e.g., $M_1$). If the logic transistors are the bottleneck (have higher resistance), adding more capacitance to the internal nodes will slow down the circuit.\n        *   The capacitance at nodes $X$ and $Y$ increases. The delay $\\tau \\approx R_{total} C_{total}$. While $R_{total}$ decreases slightly, $C_{total}$ increases. In many dynamic logic designs, the parasitic capacitance increase outweighs the resistance reduction, especially because the logic transistors ($M_1$) limit the current.\n\n**Conclusion:**\nIn high-speed dynamic circuit design, clocked transistors are typically kept to minimum size to minimize clock load and parasitic capacitance. Increasing their widths adds significant capacitive load to the clock and the dynamic nodes, which generally **degrades** the speed (maximum operating frequency) of the circuit.\n\n**Answer:** The speed **degrades**.",
        "format": "markdown",
        "sha256": "1fd4d347632b0afba57b0538ee1fcbb29f5fde9b85d6e931deb5a4541b1bd4e5"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The answer recognizes that widening lowers on-resistance and adds capacitance, but concludes that speed generally degrades. The key result is that speed improves initially as clocked-device resistance falls, with added capacitance limiting or potentially reversing the benefit at larger widths.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 12658,
        "total_tokens": 14353,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12067,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 12658,
        "total_tokens": 14353,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12067,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the analysis of the circuit, which appears to be a TSPC (True Single Phase Clock) latch or a similar dynamic logic structure (specifically forming a ring oscillator or flip-flop with feedback):\n\n**The speed improves.**\n\nHere is the reasoning:\n1.  **Reduced Resistance:** The clocked transistors (those with gates connected to $CK$ and $\\overline{CK}$) are in series with the logic transistors (like $M_1$ and the top PMOS devices). In a MOSFET, increasing the channel width ($W$) decreases the on-resistance ($R_{on} \\propto 1/W$).\n2.  **Faster Switching:** By reducing the resistance of the clocked transistors, the total resistance of the charging and discharging paths for the internal nodes ($X$ and $Y$) is reduced. This allows the nodes to charge and discharge more quickly ($I = V/R$, so higher current leads to faster $dV/dt$).\n3.  **Propagation Delay:** The propagation delay of the circuit stages is roughly proportional to $R_{eq} \\cdot C_{load}$. While increasing the width does increase the parasitic drain capacitance (self-loading), the reduction in resistance typically dominates for the series path, leading to a decrease in the time constant and thus an improvement in speed (higher maximum operating frequency).\n\n*Note: In a real-world design, there is a trade-off. Increasing the width too much will increase the capacitive load on the clock signal ($CK$) and the internal nodes significantly, which can eventually degrade performance due to clock skew or excessive parasitic capacitance. However, generally, sizing up series transistors from a minimum size improves speed.*",
        "format": "markdown",
        "sha256": "d04e6a459205ddb458b3e7f6a6ef2df3ce62d3c059554ac80a443b6596266f60"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly says widening the clocked transistors improves speed by reducing their on-resistance, while added capacitance at the latch nodes eventually limits or can reverse the benefit.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 12453,
        "total_tokens": 14148,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12079,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 12453,
        "total_tokens": 14148,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 12079,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-010-speed-improve-or-degrade-increase-widths-clocked",
      "part": "part2",
      "question_number": 10,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-010-speed-improve-or-degrade-increase-widths-clocked/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the analysis of the circuit, which appears to be a dynamic logic circuit (specifically resembling a C2MOS latch or a TSPC flip-flop structure), here is the evaluation:\n\n**The speed degrades.**\n\n**Reasoning:**\n1.  **Parasitic Capacitance at Internal Nodes:** The clocked transistors (those with gates connected to $CK$ and $\\overline{CK}$) are connected directly to the internal dynamic nodes $X$ and $Y$. Increasing the width ($W$) of these transistors increases their drain diffusion capacitance. This adds significant parasitic capacitance to nodes $X$ and $Y$.\n2.  **Increased Time Constant:** The speed of the circuit is determined by how fast nodes $X$ and $Y$ can charge and discharge. The delay is proportional to the product of resistance and capacitance ($\\tau \\approx R \\cdot C$). While increasing the width reduces the ON-resistance ($R$) of the clocked transistors, it increases the capacitance ($C$) at the node. In dynamic circuits, the parasitic capacitance at the dynamic node is often a critical factor. The increase in capacitance often outweighs the benefit of reduced resistance, especially because the logic transistors (like $M_1$) are in series and their resistance remains unchanged, becoming the bottleneck.\n3.  **Clock Load:** Increasing the width of the clocked transistors also increases the gate capacitance seen by the clock signals ($CK$ and $\\overline{CK}$). This increases the load on the clock distribution network, potentially slowing down the clock edges, which can further degrade the overall performance and speed of the circuit.\n\nTherefore, increasing the widths of the clocked transistors generally leads to a degradation in speed due to the increased parasitic capacitance at the critical internal nodes.",
        "format": "markdown",
        "sha256": "d06dda79b86c9e83e637837b40c2eed7397e7b5f4cf7b3df57783cac1c36ad54"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that wider clocked transistors reduce on-resistance but concludes that speed degrades. The expected trend is an initial speed improvement, with added node capacitance limiting or eventually reversing the benefit.",
          "golden_solution_sha256": "93d9b522d441668a699cc09168ad1991cf00bb982a5ad716cae0b7c7bec7c4fd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 11091,
        "total_tokens": 12786,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1695,
        "output_tokens": 11091,
        "total_tokens": 12786,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10692,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the structure in the figure provides quadrature outputs.\n\n**Analysis:**\n1.  **Circuit Identification:** The circuit shown is a **True Single Phase Clock (TSPC) divide-by-2 circuit**. It consists of two dynamic logic latches (the left and right blocks) and an inverter ($\\text{Inv}_3$) forming a feedback loop.\n2.  **Operation:**\n    *   The circuit acts as a frequency divider, producing an output frequency that is half of the input clock frequency ($f_{out} = f_{CK} / 2$).\n    *   The left block (producing node $X$) and the right block (producing node $Y$) are clocked on opposite phases of the input clock ($CK$ and $\\overline{CK}$).\n    *   Specifically, one stage is transparent/active during the high phase of $CK$, and the other during the low phase. This creates a master-slave configuration.\n3.  **Phase Relationship:**\n    *   Because the two stages are triggered on opposite edges of the input clock (e.g., rising edge for one, falling edge for the other), there is a time delay of half an input clock period ($T_{CK}/2$) between the transitions at node $X$ and node $Y$.\n    *   The period of the output signal (at $X$ or $Y$) is $T_{out} = 2 \\cdot T_{CK}$.\n    *   The phase difference $\\phi$ between $X$ and $Y$ is calculated as:\n        $$ \\phi = \\frac{\\text{Time Delay}}{T_{out}} \\times 360^{\\circ} = \\frac{T_{CK} / 2}{2 \\cdot T_{CK}} \\times 360^{\\circ} = \\frac{1}{4} \\times 360^{\\circ} = 90^{\\circ} $$\n4.  **Conclusion:** The signals at nodes **$X$** and **$Y$** (and consequently $Z$, which is the inverse of $Y$) are separated by 90 degrees. Therefore, the circuit generates quadrature outputs. Typically, $X$ and $Y$ (or $X$ and $Z$) would be used as the quadrature signals ($I$ and $Q$).",
        "format": "markdown",
        "sha256": "b4ca951d9ed955ff10f7f2b874db2fa227790739b70989939db189ee0eeec27d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the nominal divide-by-two quadrature from the half-period spacing, but omits the Inv3 delay and unequal latch loading that make the outputs non-ideal; it also misidentifies the topology as TSPC rather than C2MOS.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 6698,
        "total_tokens": 8377,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6182,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 6698,
        "total_tokens": 8377,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6182,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the structure in the figure provides quadrature outputs.\n\n**Reasoning:**\nThe circuit shown is a **True Single Phase Clock (TSPC)** based frequency divider, specifically configured as a **quadrature generator** (or a divide-by-2 circuit with quadrature outputs).\n\n1.  **Circuit Topology:** It consists of two cascaded dynamic latches (the left block producing node $X$ and the right block producing node $Y$) followed by an inverter ($\\text{Inv}_3$) producing node $Z$. There is a feedback loop from $Z$ to the input of the first latch.\n2.  **Operation:** This configuration acts like a 2-stage Johnson counter (twisted ring counter).\n    *   The first latch (left) samples the feedback signal $Z$ on one phase of the clock.\n    *   The second latch (right) samples the output of the first latch ($X$) on the opposite phase of the clock.\n3.  **Phase Relationship:**\n    *   The output signal at node $Y$ (and its inverse $Z$) has a frequency of $f_{CK}/2$.\n    *   The internal node $X$ transitions on one clock edge, while node $Y$ transitions on the opposite clock edge.\n    *   Since the period of the output signal is $2 \\times T_{CK}$, a time delay of $T_{CK}/2$ (half a clock period) between the transitions of $X$ and $Y$ corresponds to a phase shift of $\\frac{T_{CK}/2}{2 T_{CK}} \\times 360^{\\circ} = 90^{\\circ}$.\n    *   Therefore, the signal at node **$X$** and the signal at node **$Y$** (or $Z$) are **90 degrees out of phase**, which is the definition of quadrature.\n\nSo, nodes $X$ and $Y$ (or $X$ and $Z$) provide the quadrature outputs.",
        "format": "markdown",
        "sha256": "380b38032be5be1345c32b630af9ac4503bc8643124425879c12709cf3424b2d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the nominal divide-by-two quadrature from the opposite-phase latch transitions, but omits both sources of nonideal phase error: Inv3 delay and unequal latch loading. It therefore overstates the outputs as quadrature without qualification.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 7218,
        "total_tokens": 8897,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 7218,
        "total_tokens": 8897,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6775,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-011-structure-provide-quadrature-outputs",
      "part": "part2",
      "question_number": 11,
      "question": "Does the structure in the figure provide quadrature outputs?",
      "figures": [
        "tasks/part2-011-structure-provide-quadrature-outputs/figure-10.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, the structure in the figure provides quadrature outputs.\n\n**Analysis:**\nThe circuit is a divide-by-2 frequency divider constructed using C2MOS (Clocked CMOS) latches. It consists of two latch stages and an inverter ($Inv_3$) in a feedback loop.\n\n1.  **Left Stage (controlled by $CK$ and $\\overline{CK}$):** When $CK$ is high, this stage is transparent and acts as an inverter for the feedback signal $Z$. So, $X = \\overline{Z}$. When $CK$ is low, the node $X$ holds its state.\n2.  **Right Stage (controlled by $CK$ and $\\overline{CK}$):** When $CK$ is low (and $\\overline{CK}$ is high), this stage is transparent and acts as an inverter for the signal $X$. So, $Y = \\overline{X}$. When $CK$ is high, the node $Y$ holds its state.\n3.  **Inverter Stage:** The output $Z$ is the inverse of $Y$, so $Z = \\overline{Y}$.\n\n**Waveform Behavior:**\nLet's trace the signals over one full clock cycle (period $T$):\n*   **Phase 1 ($CK=1$):** The left stage updates $X$ to $\\overline{Z}$. The right stage holds $Y$.\n*   **Phase 2 ($CK=0$):** The left stage holds $X$. The right stage updates $Y$ to $\\overline{X}$, and consequently $Z$ updates to $\\overline{Y} = X$.\n\nThis creates a sequence where the output signals toggle at half the clock frequency ($f_{out} = f_{CK}/2$).\n*   Signal **$X$** is a square wave with a 50% duty cycle.\n*   Signal **$Y$** (and its inverse **$Z$**) is also a square wave with a 50% duty cycle.\n*   The transition of $Y$ occurs a half-clock cycle after the transition of $X$. Since the total period of the output signal is two clock cycles ($2T$), a delay of $T/2$ corresponds to a phase shift of:\n    $$ \\text{Phase Shift} = \\frac{T/2}{2T} \\times 360^{\\circ} = \\frac{1}{4} \\times 360^{\\circ} = 90^{\\circ} $$\n\nTherefore, the signals at nodes **$X$** and **$Y$** (or **$X$** and **$Z$**) are 90 degrees out of phase, which means they are **quadrature outputs**. This circuit is commonly used as a quadrature clock generator.",
        "format": "markdown",
        "sha256": "55561a2c851e18fbaca53fe15f318c8c069014fcbb3f0e44d532b892095f3174"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly identifies the nominal divide-by-two quadrature from the latches switching half an input period apart, but omits both reasons the outputs are not exactly in quadrature: Inv3 delay and unequal latch loading.",
          "golden_solution_sha256": "a208e36107d3c6d3d835e897ccf309733e82f6921b41cd2eef1a21949e70e6f6",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 7806,
        "total_tokens": 9485,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7191,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1679,
        "output_tokens": 7806,
        "total_tokens": 9485,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7191,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, the speed **improves**.\n\nHere is the step-by-step reasoning:\n\n1.  **Identify the Circuit:** The figure shows a Clocked CMOS (C2MOS) latch or flip-flop structure. It consists of logic blocks controlled by clock signals ($CK$ and $\\overline{CK}$). The transistors connected directly to the clock signals (the top PMOS and bottom NMOS transistors in each branch) are the \"clocked transistors.\"\n\n2.  **Role of Clocked Transistors:** These transistors act as switches that connect the internal logic gates to the power supply ($V_{DD}$) and ground (GND) during specific phases of the clock cycle. They are in series with the logic transistors.\n\n3.  **Effect of Increasing Width:**\n    *   **Resistance:** The on-resistance ($R_{on}$) of a MOSFET is inversely proportional to its width ($W$). Therefore, increasing the width of the clocked transistors decreases their resistance.\n    *   **Current Drive:** Lower resistance allows more current to flow through the transistors. This means the circuit can charge or discharge the internal node capacitances faster.\n    *   **Delay:** The propagation delay of the circuit is largely determined by the RC time constant ($\\tau \\approx R \\cdot C$). By reducing the resistance ($R$) of the series path (clocked transistor + logic transistor), the time it takes to switch the output state is reduced.\n\n**Conclusion:**\nBy increasing the widths of the clocked transistors, you reduce the series resistance in the charging and discharging paths. This allows the nodes to switch faster, thereby **improving the speed** (reducing the propagation delay) of the circuit.\n\n*(Note: While speed improves, there is a trade-off. Increasing the width also increases the capacitive load on the clock signal lines ($CK$ and $\\overline{CK}$), which requires more power to drive the clock.)*",
        "format": "markdown",
        "sha256": "6c446b51cf915e51dec7479df61e0dfd22f9a932c34bbbafe67c010b92274a03"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that widening the clocked transistors improves speed because it reduces their on-resistance. It omits the charge-sharing effect and the topology-specific explanation that added capacitance has little effect on the data path.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1704,
        "output_tokens": 3385,
        "total_tokens": 5089,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2947,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1704,
        "output_tokens": 3385,
        "total_tokens": 5089,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 2947,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the answer:\n\n**The speed improves.**\n\n**Reasoning:**\n1.  **Identify the Clocked Transistors:** The clocked transistors are the four transistors controlled by the clock signals $CK$ and $\\overline{CK}$ (the top PMOS transistors connected to $V_{DD}$ and the bottom NMOS transistors connected to Ground).\n2.  **Role in Circuit:** These transistors act as switches in series with the logic transistors (the inner cross-coupled pair). They enable or disable the current path from the power supply ($V_{DD}$) or ground to the output nodes.\n3.  **Effect of Increasing Width:**\n    *   **Reduced Resistance:** The on-resistance ($R_{on}$) of a MOSFET is inversely proportional to its width ($W$). By increasing the width of the clocked transistors, you decrease their resistance.\n    *   **Increased Drive Current:** A wider transistor can conduct more current ($I_{ds} \\propto W$).\n    *   **Faster Switching:** The speed of a digital circuit is largely determined by how fast it can charge and discharge the capacitive nodes (RC delay). Since the total resistance of the charging/discharging path is reduced ($R_{total} = R_{clocked} + R_{logic}$), the time constant ($\\tau = R \\cdot C$) decreases. This allows the nodes to switch states faster, reducing the propagation delay.\n\n**Note:** While the data path speed improves, increasing the width also increases the gate capacitance, which puts a heavier load on the clock driver ($CK$ and $\\overline{CK}$ signals). However, in the context of the logic circuit's switching speed, the reduction in series resistance leads to an improvement.",
        "format": "markdown",
        "sha256": "0132f1b894ab515181a7ad39e7dc3e31efd8ac58176943ede5285a96c8880497"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that widening the clocked transistors improves speed by reducing their series on-resistance. It omits charge sharing, which degrades the swing and limits the benefit.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 1152,
        "input_tokens": 1704,
        "output_tokens": 5870,
        "total_tokens": 7574,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5471,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 1152,
        "input_tokens": 1704,
        "output_tokens": 5870,
        "total_tokens": 7574,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5471,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-012-repeat-question-10-for-topology",
      "part": "part2",
      "question_number": 12,
      "question": "In the circuit shown in the figure, does the speed improve or degrade if we increase the widths of the clocked transistors?",
      "figures": [
        "tasks/part2-012-repeat-question-10-for-topology/figure-11.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, here is the evaluation:\n\n**Circuit Identification:**\nThe circuit shown is a **C2MOS (Clock-CMOS) latch** (or a similar dynamic latch structure like a TSPC latch variant). It consists of two clocked inverters connected in a loop with a static inverter at the output. The transistors controlled by $CK$ and $\\overline{CK}$ are the \"clocked transistors.\" They act as switches to enable or disable the inverters during specific clock phases.\n\n**Analysis of Increasing Width:**\n1.  **Resistance Reduction:** The clocked transistors are connected in series with the logic transistors (the inner transistors whose gates are driven by the signal). The total resistance of the pull-up or pull-down path is the sum of the resistance of the clocked transistor ($R_{clk}$) and the logic transistor ($R_{logic}$).\n    *   Increasing the width ($W$) of a MOS transistor decreases its on-resistance ($R_{on} \\propto 1/W$).\n    *   Therefore, increasing the width of the clocked transistors reduces the total series resistance ($R_{total} = R_{clk} + R_{logic}$).\n\n2.  **Delay Reduction (Speed Improvement):** The speed of the circuit (specifically the propagation delay) is largely determined by the time it takes to charge or discharge the load capacitance ($C_L$) at the output nodes. The delay $\\tau$ is approximately proportional to $R_{total} \\times C_L$.\n    *   Since $R_{total}$ decreases, the time constant decreases, allowing the nodes to switch faster. This **improves** the speed.\n\n3.  **Capacitance Penalty (Secondary Effect):** Increasing the width also increases the parasitic capacitances (gate capacitance and diffusion capacitance).\n    *   The gate capacitance increases the load on the clock signal ($CK, \\overline{CK}$), which can slow down the clock edges if the clock driver is weak.\n    *   The diffusion capacitance at the internal nodes (between the clocked and logic transistors) increases. However, in the Elmore delay model, the term associated with this internal node ($R_{clk} \\times C_{internal}$) remains roughly constant because $R_{clk}$ decreases by the same factor that $C_{internal}$ increases.\n    *   The dominant term for the output node delay is $(R_{clk} + R_{logic}) \\times C_L$. Since $R_{clk}$ decreases, this term decreases significantly.\n\n**Conclusion:**\nGenerally, increasing the widths of the clocked transistors **improves** the speed of the circuit because it reduces the series resistance in the charging/discharging paths, allowing for faster switching of the output nodes. (Note: This holds true up to a point; if the transistors become too large, the increased capacitive load on the clock signal could eventually become a bottleneck, but the primary effect on the logic path is an improvement).\n\n**Answer:** The speed **improves**.",
        "format": "markdown",
        "sha256": "1d48b445e2f1c019cfb5725fdc215ac891e696eafc50c956e2672791bc910867"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly concludes that widening the clocked transistors improves speed by reducing their series resistance. It omits the key charge-sharing effect that degrades the swing, so it does not earn full credit.",
          "golden_solution_sha256": "318c27e5f5623103c64ba9716043fb25f88281b2efa86f52761064364631036f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1704,
        "output_tokens": 11414,
        "total_tokens": 13118,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10747,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1704,
        "output_tokens": 11414,
        "total_tokens": 13118,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 10747,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the arrangement:\n\n**1. Component Identification**\n*   **Switches:** There are two switches labeled **$CK$** and **$\\overline{CK}$**. These represent complementary switches, likely transmission gates or pass transistors controlled by a clock signal. When $CK$ is closed (conducting), $\\overline{CK}$ is open (non-conducting), and vice versa.\n*   **Inverters:** There are three triangular symbols with circles at their tips, representing inverters (NOT gates). The first one is labeled **$Inv_1$**.\n*   **Feedback Loop:** The output of the final inverter is connected via a wire back to the input of the first switch ($CK$), forming a closed loop.\n\n**2. Circuit Topology**\nThe circuit consists of a ring of three inverters. Normally, an odd number of inverters connected in a loop creates a **ring oscillator** that oscillates freely. However, this loop is interrupted by two switches controlled by a clock.\n\n**3. Operational Analysis**\nThe circuit operates in two phases based on the clock signal:\n\n*   **Phase 1: $CK$ is High (Closed), $\\overline{CK}$ is Low (Open)**\n    *   The switch $CK$ closes, connecting the feedback output to the input of $Inv_1$.\n    *   $Inv_1$ inverts the input signal. If the current output is $Q$, the output of $Inv_1$ becomes $\\overline{Q}$.\n    *   The switch $\\overline{CK}$ is open, breaking the connection to the rest of the chain. The value $\\overline{Q}$ is effectively stored at the node between $Inv_1$ and the $\\overline{CK}$ switch (in a real circuit, this is held by parasitic capacitance).\n    *   The second and third inverters are isolated from the new input, so the final output $Q$ remains unchanged (holding its previous state).\n\n*   **Phase 2: $CK$ is Low (Open), $\\overline{CK}$ is High (Closed)**\n    *   The switch $CK$ opens, isolating the input.\n    *   The switch $\\overline{CK}$ closes, passing the stored value ($\\overline{Q}$) to the input of the second inverter.\n    *   The signal passes through the second inverter (becoming $Q$) and then the third inverter (becoming $\\overline{Q}$).\n    *   The new output at the end of the chain is now $\\overline{Q}$.\n\n**4. Conclusion**\nSince the output flips from $Q$ to $\\overline{Q}$ after one full clock cycle (a high phase followed by a low phase), the circuit acts as a **Toggle Flip-Flop (T-FF)** or a **Divide-by-2 Frequency Divider**.\n\n*   **Function:** For every two clock pulses (one full period of the control signal), the output completes one full cycle.\n*   **Summary:** It is a dynamic logic circuit that toggles its state on each clock cycle, effectively dividing the input clock frequency by 2.",
        "format": "markdown",
        "sha256": "55e604b8d7c10a5893848b29b2ef068e5a0040d309c685bca9e736b64c362bae"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the arrangement as a dynamic divide-by-two/toggle circuit. Its detailed inverter-path description is secondary under the golden solution’s full-credit rule.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 5155,
        "total_tokens": 6239,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4457,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 5155,
        "total_tokens": 6239,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4457,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the arrangement:\n\n**1. Component Identification:**\n*   **Inverters (NOT gates):** There are three triangular symbols with a circle at the tip, representing inverters. The first one is labeled **Inv₁**.\n*   **Switches:** There are two switches labeled **CK** and **$\\overline{CK}$** (CK bar). The bar notation indicates that these are complementary switches controlled by a clock signal. When **CK** is closed (logic high), **$\\overline{CK}$** is open (logic low), and vice versa.\n*   **Feedback Loop:** A wire connects the output of the last inverter back to the input of the first switch, forming a closed loop.\n\n**2. Circuit Topology:**\nThe circuit is a loop containing an odd number of inverters (three). In digital logic, a loop with an odd number of inverters creates a **Ring Oscillator** because the signal is constantly inverted, leading to instability and oscillation. However, the presence of the switches modifies this behavior.\n\n**3. Operational Analysis:**\nThe circuit operates in two phases determined by the clock signals:\n\n*   **Phase 1: CK is High (Closed), $\\overline{CK}$ is Low (Open)**\n    *   The first switch (**CK**) closes, allowing the signal from the feedback loop (the output of the last inverter) to pass into **Inv₁**.\n    *   **Inv₁** inverts this signal.\n    *   The second switch (**$\\overline{CK}$**) is open, so the signal stops here. The inverted value is effectively \"sampled\" or held at this node (in a real CMOS circuit, this would be held by parasitic capacitance).\n    *   The rest of the circuit (the last two inverters) is isolated from the input and holds its previous state.\n\n*   **Phase 2: CK is Low (Open), $\\overline{CK}$ is High (Closed)**\n    *   The first switch opens.\n    *   The second switch (**$\\overline{CK}$**) closes, passing the sampled inverted signal from the previous phase into the chain of the remaining two inverters.\n    *   The signal passes through the second and third inverters. Since two inverters in series act as a buffer (non-inverting), the signal polarity relative to the intermediate node is preserved, but relative to the very beginning, the total chain has performed 3 inversions.\n    *   The final output is the inverse of the original input.\n\n**4. Conclusion:**\n*   **Logic Function:** The total path through the loop contains 3 inverters. Therefore, the output fed back is the logical inverse of the current state ($Q_{new} = \\overline{Q_{old}}$).\n*   **Behavior:** Because the state flips (toggles) every time a full clock cycle completes (Phase 1 then Phase 2), this circuit functions as a **Toggle Flip-Flop (T-Flip-Flop)** or a **Divide-by-2 Frequency Divider**.\n*   **Summary:** It is a dynamic logic circuit that toggles its output state on every clock cycle. If the input clock frequency is $f$, the output signal at the loop will toggle at a frequency of $f/2$.",
        "format": "markdown",
        "sha256": "274d12a98d768cf6e6517b25fc7bc656ceabc509e8af16cf7a206b0965a701e9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies the arrangement as a dynamic divide-by-two and describes clocked sampling/holding and output toggling at half the input frequency. The imprecise inverter-path details are secondary.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 6339,
        "total_tokens": 7423,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5627,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 6339,
        "total_tokens": 7423,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5627,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-013-dynamic-latch-divide-by-two",
      "part": "part2",
      "question_number": 13,
      "question": "Analyze the arrangement in the figure.",
      "figures": [
        "tasks/part2-013-dynamic-latch-divide-by-two/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the provided circuit diagram, here is an analysis of the arrangement:\n\n**1. Component Identification**\n*   **Inverters (NOT Gates):** There are three triangular symbols with a circle at the tip, representing inverters. The first one is explicitly labeled **Inv₁**.\n*   **Switches:** There are two switches labeled **CK** and **$\\overline{CK}$** (CK bar). The bar notation indicates that these are complementary switches controlled by a clock signal. When CK is closed (logic high), $\\overline{CK}$ is open (logic low), and vice versa. This suggests a two-phase non-overlapping clock system.\n*   **Feedback Loop:** A wire connects the output of the final inverter back to the input of the first switch (CK), creating a closed loop.\n\n**2. Logical Analysis**\nTo understand the circuit's behavior, we can trace the signal through the loop:\n*   The signal starts at the output of the last inverter.\n*   It passes through the **CK** switch.\n*   It goes through **Inv₁** (1st inversion).\n*   It passes through the **$\\overline{CK}$** switch.\n*   It goes through the second inverter (2nd inversion).\n*   It goes through the third inverter (3rd inversion).\n*   The result is fed back to the start.\n\nSince there are **three inverters** (an odd number) in the loop, the total logic function is an inversion. If the input is $Q$, the feedback signal will be $\\overline{Q}$ (NOT Q). In digital logic, a loop with an odd number of inversions creates an unstable state that leads to oscillation (a Ring Oscillator).\n\n**3. Operational Phases**\nThe switches control the timing of this oscillation, effectively turning it into a clocked dynamic circuit.\n\n*   **Phase 1: CK is High (Closed), $\\overline{CK}$ is Low (Open)**\n    *   The feedback signal from the end of the chain is connected to the input of **Inv₁**.\n    *   **Inv₁** inverts this signal.\n    *   The output of **Inv₁** is now \"stuck\" or held at the open switch $\\overline{CK}$ (likely stored on parasitic capacitance in a real dynamic circuit). The rest of the chain is isolated.\n\n*   **Phase 2: CK is Low (Open), $\\overline{CK}$ is High (Closed)**\n    *   The connection from the feedback loop is broken.\n    *   The stored signal from **Inv₁** is now allowed to pass through the closed $\\overline{CK}$ switch.\n    *   The signal travels through the remaining two inverters. Since two inverters in series act as a non-inverting buffer (logic-wise), the signal at the end of the chain will be the inverse of the value sampled in Phase 1.\n    *   Specifically: If the initial output was $0$, Phase 1 creates a $1$ at the intermediate node. Phase 2 passes this $1$ through two inverters ($1 \\rightarrow 0 \\rightarrow 1$). Wait, let's re-trace carefully.\n        *   Let Output = 0.\n        *   Phase 1: Input to Inv₁ is 0. Output of Inv₁ is 1.\n        *   Phase 2: Input to 2nd Inv is 1. Output of 2nd Inv is 0. Output of 3rd Inv is 1.\n        *   New Output = 1.\n    *   The state has toggled from 0 to 1.\n\n**Conclusion**\nThis arrangement is a **dynamic ring oscillator** or a **clocked toggle circuit** (functioning like a T-flip-flop or divide-by-2 counter).\n\n*   Because the loop contains an odd number of inversions, the circuit wants to oscillate.\n*   The complementary switches ($CK$ and $\\overline{CK}$) gate this oscillation, forcing the circuit to update its state only once per full clock cycle (one CK phase + one $\\overline{CK}$ phase).\n*   The output frequency will be half the frequency of the clock signal controlling the switches ($f_{out} = f_{ck} / 2$).",
        "format": "markdown",
        "sha256": "031991b810e67412699e57b7704099c3936e8d047d9b49d710ceea1b0f0af64a"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "It correctly concludes that the clocked dynamic circuit toggles and divides the input frequency by two, and describes sampling and holding. However, calling it an odd-inverter ring oscillator and claiming that this causes instability mischaracterizes the circuit’s operation.",
          "golden_solution_sha256": "f425c26bf4178562557e147f38673688c0fa91f97a1c7cad9ab3d6417d10545f",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 5353,
        "total_tokens": 6437,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1084,
        "output_tokens": 5353,
        "total_tokens": 6437,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4419,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram, which appears to be a ring oscillator (a chain of inverters with feedback), here is how the red inverter affects the performance:\n\n1.  **Increases Oscillation Frequency:** The red inverter is connected in parallel with the first stage (the path containing the switch $CK$ and the black inverter $\\text{Inv}_1$). By providing a parallel path for the signal, it effectively reduces the propagation delay of that stage. In a ring oscillator, the frequency is inversely proportional to the total delay of the loop ($f \\approx \\frac{1}{2 \\cdot N \\cdot t_{pd}}$). Reducing the delay of one stage decreases the total period, thereby **increasing the oscillation frequency**.\n\n2.  **Increases Drive Strength:** The red inverter acts as an additional driver for the node between $\\text{Inv}_1$ and the second switch. When both the red inverter and the black inverter (when the switch is closed) are active, they provide more current to charge and discharge the load capacitance of the next stage. This faster charging/discharging leads to faster switching times.\n\n3.  **Increases Power Consumption:** Adding an extra inverter that switches continuously adds to the dynamic power consumption of the circuit ($P = C V^2 f$). There is also the static power consideration if there are any leakage currents, but primarily the dynamic power increases due to the extra gate capacitance being switched.\n\n4.  **Bypass Function (depending on switch state):** If the switch $CK$ is open, the main path through $\\text{Inv}_1$ is broken. However, the red inverter maintains a connection from the input node to the next stage. This ensures that the signal can still propagate through the red inverter to the rest of the chain (assuming $\\overline{CK}$ is closed), potentially allowing the oscillator to run in a different mode or frequency even when the primary switch is open.\n\n**Summary:** The primary effect is to **reduce the delay** of the first stage, which results in a **higher oscillation frequency** for the circuit.",
        "format": "markdown",
        "sha256": "ccf228e79e1e6f02ede8e9c5dbe68d0831e935c6f6fab0049574d9986aa5803c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that the red inverter provides a bypass path that can improve speed, but miscasts the divider as a ring oscillator and misses the key low-frequency drawback: the unclocked branch can overpower the latch and raise the minimum usable clock frequency. Its claim that the inverters simply add drive also overlooks their contention.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 5499,
        "total_tokens": 6436,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 5499,
        "total_tokens": 6436,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5051,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of how the red inverter affects performance:\n\n**1. Circuit Identification**\nThe circuit depicts a **Ring Oscillator**. It consists of a loop of inverters (an odd number of inverting stages is required for oscillation). The switches labeled $CK$ and $\\overline{CK}$ suggest this is a controlled or gated oscillator, possibly used in a Phase-Locked Loop (PLL) or as a voltage-controlled oscillator (VCO) where the delay is modulated.\n\n**2. Connection of the Red Inverter**\nThe red inverter is connected in **parallel** with the first stage of the circuit. Specifically:\n*   Its input is connected to the node before the first switch ($CK$).\n*   Its output is connected to the node after the first black inverter ($Inv_1$).\n\nThis means the red inverter provides an alternative signal path that bypasses the first switch ($CK$) and runs parallel to the first inverter ($Inv_1$).\n\n**3. Effect on Performance**\n\n*   **Increased Oscillation Frequency (Speed):**\n    *   By placing an inverter in parallel with the existing path, you effectively increase the **drive strength** (current capability) of that stage. It is similar to making the inverter larger (wider transistors).\n    *   A stronger drive allows the node capacitance to charge and discharge faster, which reduces the **propagation delay** of that stage.\n    *   Since the frequency of a ring oscillator is inversely proportional to the total delay of the loop ($f \\approx \\frac{1}{2 \\cdot N \\cdot t_{delay}}$), reducing the delay of one stage will **increase the overall oscillation frequency**.\n\n*   **Bypassing Switch Resistance:**\n    *   If the switch labeled $CK$ represents a transistor (like a pass gate) with significant on-resistance, the red inverter provides a \"fast path\" that bypasses this resistance. This further reduces the delay for that stage.\n\n*   **Increased Power Consumption:**\n    *   Adding an extra inverter means there are more transistors switching states during each cycle. This increases the dynamic power consumption ($P = C \\cdot V^2 \\cdot f$) due to the additional capacitance being charged and discharged.\n\n*   **Improved Slew Rate / Reduced Jitter:**\n    *   The increased drive strength results in faster signal transitions (sharper edges). This can make the circuit less susceptible to noise, potentially reducing **jitter** (timing uncertainty) in the oscillator's output.\n\n**Summary**\nThe red inverter acts as a parallel driver that **speeds up the first stage**, thereby **increasing the frequency** of the oscillator, at the cost of **higher power consumption**.",
        "format": "markdown",
        "sha256": "2bdabdcdfa48e313302b4a8193d0595326a36ef32a2ef500b555c8ae12d57cd9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes that the red inverter provides a bypass path around the CK switch and Inv1, which can improve speed. But it mischaracterizes the circuit as a ring oscillator and the red inverter as a parallel-strengthening driver, and misses the key low-frequency drawback: the unclocked branch can fight the main path and raise the minimum usable clock frequency.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 6144,
        "total_tokens": 7081,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5545,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 6144,
        "total_tokens": 7081,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5545,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-014-red-inverter-b-affect-performance",
      "part": "part2",
      "question_number": 14,
      "question": "How does the red inverter in the figure affect the performance?",
      "figures": [
        "tasks/part2-014-red-inverter-b-affect-performance/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is an analysis of how the red inverter affects the performance:\n\n**1. Circuit Identification**\nThe circuit shown is a **ring oscillator**, which consists of an odd number of inverters connected in a loop (feedback path). Ring oscillators are commonly used to generate clock signals, and their frequency is determined by the propagation delay of the inverters in the chain.\n\n**2. Connection of the Red Inverter**\nThe red inverter is connected in **parallel** with the first stage of the oscillator (specifically, in parallel with the series combination of the switch $CK$ and the inverter $Inv_1$).\n*   **Input:** It takes the signal from the node before the switch $CK$.\n*   **Output:** It drives the node after $Inv_1$ (before the switch $\\overline{CK}$).\n\n**3. Effect on Performance**\n\n*   **Reduced Propagation Delay (Increased Speed):**\n    When the switch $CK$ is closed, the red inverter and the black inverter ($Inv_1$) are effectively in parallel. This configuration increases the total drive strength (current capability) driving the output node.\n    *   Two inverters in parallel can charge and discharge the load capacitance faster than a single inverter.\n    *   This reduces the propagation delay ($t_{pd}$) of this specific stage.\n\n*   **Increased Oscillation Frequency:**\n    The frequency of a ring oscillator is inversely proportional to the total delay of the loop ($f \\approx \\frac{1}{2 \\cdot N \\cdot t_{pd}}$).\n    *   Since the red inverter reduces the delay of the first stage, the total loop delay decreases.\n    *   Consequently, the **oscillation frequency increases**.\n\n*   **Increased Power Consumption:**\n    Adding an extra inverter that switches continuously increases the dynamic power consumption of the circuit ($P = C V^2 f$). There is also increased capacitance at the input node (loading the previous stage) and the output node.\n\n*   **Operational Redundancy / Path Selection:**\n    The switches $CK$ and $\\overline{CK}$ suggest this is a controllable circuit (like a Voltage Controlled Oscillator or a dynamic logic circuit).\n    *   If the switch $CK$ is **open** (disabled), the path through $Inv_1$ is broken. The red inverter ensures that there is still an active inversion path from the input to the output of this stage. This allows the ring oscillator to continue functioning (through the path: Red Inverter $\\rightarrow$ Switch $\\overline{CK}$ $\\rightarrow$ next inverters), likely at a lower base frequency.\n    *   If the switch $CK$ is **closed**, the red inverter works alongside $Inv_1$ to boost performance (speed).\n\n**Summary**\nThe red inverter primarily acts to **decrease the delay** of the first stage, which **increases the overall oscillation frequency** of the circuit. It also provides a necessary signal path when the switch $CK$ is open, ensuring the oscillator remains functional.",
        "format": "markdown",
        "sha256": "8fcd31e22da90f2374e38468f33e6ba1784dd37d8b7b6c81bf2db933655253e2"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It recognizes the bypass path and its high-speed benefit, but misidentifies the circuit as a ring oscillator and treats the unclocked branch as a useful path. It misses the key low-frequency drawback: the branch can corrupt division and raises the minimum usable clock frequency.",
          "golden_solution_sha256": "09f12aa6905fa83982420dcd1602844314d44b4575734bb31f92f5ccf31131d2",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 9317,
        "total_tokens": 10254,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8648,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 937,
        "output_tokens": 9317,
        "total_tokens": 10254,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8648,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, I **agree** with the answer provided. The statement accurately describes the function of the red inverter in the context of digital logic design, specifically regarding dynamic vs. static circuits.\n\nHere is a detailed breakdown of the actual role of the red inverter:\n\n### 1. It acts as a \"Keeper\" (Feedback Element)\nIn dynamic logic circuits, data is often stored as charge on a parasitic capacitor (a dynamic node). Over time, leakage currents will discharge this capacitor, causing the stored data (logic 0 or 1) to be lost.\n*   **Without the red inverter:** The circuit relies on the capacitance at the output of `Inv1` to hold its state when the switches change. This is a **dynamic** node. If the clock is too slow, the charge leaks away, and the data is corrupted.\n*   **With the red inverter:** The red inverter takes the output of `Inv1` and feeds it back to the input. This creates a path that actively drives the node to the correct logic level, \"keeping\" the state valid against leakage.\n\n### 2. It forms a Latch (Bistable Element)\nThe statement says it forms a \"cross-coupled latch.\" Let's trace the loop:\n*   When the switch controlled by **$CK$** is closed (logic high), the input of `Inv1` is connected to the output of the red inverter.\n*   The output of `Inv1` is connected to the input of the red inverter.\n*   This creates a loop: **`Inv1` $\\rightarrow$ Red Inverter $\\rightarrow$ Switch $\\rightarrow$ `Inv1`**.\n*   Since there are two inverters in the loop (an even number), the total feedback is positive (non-inverting). This creates a **bistable latch** (a memory element that can hold a 0 or a 1 indefinitely).\n\n### 3. It removes the minimum clock frequency requirement\n*   **Dynamic circuits** have a **minimum frequency** requirement. You must clock them fast enough to refresh the charge on the capacitors before leakage destroys the data.\n*   **Static circuits** (like the one created by adding the red inverter) use active feedback (transistors constantly fighting to maintain the voltage level) to hold the state. They do not rely on stored charge alone.\n*   Therefore, the circuit can hold its state even if the clock stops completely or runs very slowly. The \"minimum frequency\" constraint is removed.\n\n**Summary:** The red inverter converts a dynamic storage node into a static (or semi-static) latch by providing active feedback, ensuring data integrity regardless of clock speed.",
        "format": "markdown",
        "sha256": "cdac948503a0f47c0d4939716b45706c9a7eb992da9b2eb2c6b2db3834ec3516"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer misidentifies the red inverter as a cross-coupled keeper and invents a feedback connection. It misses the actual feedforward path, which can improve high-speed operation but overpower the latch at low clock rates and raise the minimum usable frequency.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 7242,
        "total_tokens": 8228,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6668,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 7242,
        "total_tokens": 8228,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 6668,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Yes, I **agree** with the answer provided. The statement accurately describes the function of the red inverter in the context of digital integrated circuit design, specifically for dynamic logic circuits.\n\nHere is a detailed breakdown of the actual role of the red inverter:\n\n**1. Context: Dynamic Logic and Leakage**\nThe circuit shown (without the red inverter) resembles a **dynamic latch** or a stage in a dynamic shift register.\n*   In dynamic circuits, data is often stored as electrical charge on a parasitic capacitor (a \"dynamic node\").\n*   This charge is not permanent; it leaks away over time due to subthreshold leakage currents in the transistors.\n*   To prevent data loss, the circuit must be \"refreshed\" or clocked frequently enough before the charge leaks away. This creates a **minimum clock frequency requirement**. If the clock is too slow (or stops), the data is lost.\n\n**2. The Role of the Red Inverter (The Keeper)**\nThe red inverter acts as a **keeper** (specifically, a static feedback keeper).\n*   **Feedback Loop:** It connects the output of `Inv1` back to the input side of the stage. Together with `Inv1`, it forms a loop of two inverters.\n*   **Bistable Element (Latch):** A loop of two inverters creates a positive feedback loop (since two inversions cancel out, making it non-inverting). This forms a bistable element, or a **latch**, which has two stable states (0 and 1).\n*   **Active Restoration:** Instead of relying solely on stored charge (which leaks), the red inverter actively drives the node to the correct logic level. If the voltage starts to drop due to leakage, the inverter loop detects this and drives it back up (or vice-versa).\n\n**3. Removing the Minimum Frequency Requirement**\n*   Because the red inverter actively maintains the logic state against leakage, the circuit no longer relies on the clock to refresh the data.\n*   The circuit effectively becomes a **static latch** (or semi-static). It can hold its state indefinitely as long as power is supplied.\n*   Therefore, the **minimum clock frequency requirement is removed** (the circuit can operate at 0 Hz, i.e., DC).\n\n**Summary**\nThe red inverter converts a dynamic storage node (which is volatile and time-dependent) into a static storage node (which is stable and time-independent) by providing a continuous feedback path that fights leakage currents.",
        "format": "markdown",
        "sha256": "4d0dc3b8f78b8ce83dc68df99c2ba11f4fe9e61e014e873facebde13f12f19a3"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 0,
          "is_full_credit": false,
          "rationale": "The answer incorrectly treats the red inverter as cross-coupled keeper feedback and claims it removes the minimum-frequency requirement. It is actually an unclocked feedforward branch that bypasses part of the latch path: it can improve high-speed operation but can overpower the intended latch behavior at low clock rates.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 8905,
        "total_tokens": 9891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8371,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 8905,
        "total_tokens": 9891,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 8371,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 0,
        "score_percent": 0,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-015-but-input-red-inverter-not-tied-output",
      "part": "part2",
      "question_number": 15,
      "question": "In the figure, somebody answers:\n\n> The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\n> This removes the minimum clock frequency requirement due to leakage.\n\nDo you agree with this answer? What is the actual role of the red inverter?",
      "figures": [
        "tasks/part2-015-but-input-red-inverter-not-tied-output/figure-12.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit analysis, I **do not agree** with the answer provided in the figure. The statement is partially correct about the structure but incorrect about the consequence (removing the minimum clock frequency requirement).\n\nHere is the detailed breakdown:\n\n### 1. Analysis of the Statement\n*   **\"The red inverter acts as a keeper, forming a cross-coupled latch with `Inv1`.\"**\n    *   **Partially True:** When the switch labeled $CK$ is closed, the red inverter and `Inv1` do form a feedback loop. The path is: Node (left) $\\rightarrow$ Switch $\\rightarrow$ `Inv1` $\\rightarrow$ Red Inverter $\\rightarrow$ Node (left). Since there are two inversions (`Inv1` and Red Inverter), this creates a positive feedback loop, which is a bistable latch (specifically, a static latch structure).\n*   **\"This removes the minimum clock frequency requirement due to leakage.\"**\n    *   **False:** The minimum clock frequency requirement is a characteristic of **dynamic circuits**, where data is stored as charge on a capacitor (a floating node) that leaks away over time. To remove this requirement, the circuit must be **static**, meaning it uses active feedback to hold the state indefinitely (DC stability).\n    *   In this circuit, the feedback loop contains the switch $CK$. When the switch $CK$ is **open** (e.g., when $CK=0$), the feedback loop is broken. The input to `Inv1` (the node between the first switch and `Inv1`) becomes a high-impedance (floating) node.\n    *   Because this node is floating during the open phase, it is a **dynamic node**. Charge leakage will eventually corrupt the data stored on this node. Therefore, the clock must cycle fast enough to refresh the data before it leaks away. The minimum frequency requirement **still exists**.\n\n### 2. The Actual Role of the Red Inverter\nThe red inverter acts as a **feedback element** that creates a **gated latch** during the active phase.\n\n*   **During the phase when $CK$ is high (Switch closed):** The red inverter and `Inv1` form a closed loop. This acts like a static latch that reinforces the current state. If this is a shift register or logic gate, the input signal (coming from the bottom wire) must be strong enough to override this feedback loop to change the state (contention).\n*   **During the phase when $CK$ is low (Switch open):** The loop is broken. The circuit relies on the capacitance of the input node of `Inv1` to hold the value temporarily (dynamic storage). The red inverter is disconnected from the storage node and cannot prevent leakage.\n\n**Conclusion:** The circuit is a **dynamic latch** (or dynamic shift register stage). The red inverter does not make it fully static because the feedback path is interrupted by the clock switch. Therefore, the minimum clock frequency requirement is **not** removed. To make it a true static latch (removing $f_{min}$), the feedback from the red inverter would need to be connected directly to the input of `Inv1` (bypassing the switch), or the switch would need to be part of a clocked inverter structure that maintains the loop (like in C2MOS logic).",
        "format": "markdown",
        "sha256": "3140b93bb43b45e927e594150540745102de7b4c6d67faf91a5175cabcf8e8c6"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It correctly rejects the claim that the minimum-frequency requirement is removed, but misreads the topology: the red inverter is not cross-coupled to Inv1 through CK. The essential feedforward bypass and its high-speed benefit/low-frequency failure mechanism are absent.",
          "golden_solution_sha256": "172cbb780508db2c8965d08eedaac49be4edfaf50993cf59fb05d5d161e1fa3c",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 14697,
        "total_tokens": 15683,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13985,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 986,
        "output_tokens": 14697,
        "total_tokens": 15683,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 13985,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the Noise Figure (NF) of the circuit while maintaining an input resistance $R_{in} = 50 \\, \\Omega$, we need to analyze the input impedance and the noise sources of the resistive feedback amplifier (specifically, a CMOS inverter with shunt-shunt feedback).\n\n**1. Input Impedance Analysis**\nThe circuit is a voltage amplifier with a feedback resistor $R_F$. The input impedance looking into the gate node (after the capacitor $C_1$) is determined by the Miller effect of the feedback resistor.\n$$R_{in} \\approx \\frac{R_F}{1 + |A_v|}$$\nwhere $A_v$ is the open-loop voltage gain of the CMOS inverter stage.\nThe gain is approximately:\n$$|A_v| \\approx (g_{m1} + g_{m2}) \\cdot R_{out}$$\nwhere $g_{m1}, g_{m2}$ are the transconductances of $M_1$ and $M_2$, and $R_{out} = r_{o1} || r_{o2}$ is the output resistance at the drain node.\n\nGiven the constraint $R_{in} = 50 \\, \\Omega$:\n$$50 = \\frac{R_F}{1 + (g_{m1} + g_{m2})R_{out}}$$\nThis implies that for a fixed $R_{in}$, if we increase $R_F$, we must proportionally increase the loop gain $(g_{m1} + g_{m2})R_{out}$.\n\n**2. Noise Figure Analysis**\nThe main noise sources contributing to the NF are:\n*   **Thermal noise of the feedback resistor $R_F$:** The noise current spectral density is $4kT/R_F$. Referred to the input, this noise contribution is inversely proportional to $R_F$. To minimize this, **$R_F$ should be as large as possible**.\n*   **Channel thermal noise of transistors $M_1$ and $M_2$:** The noise current spectral density is roughly $4kT\\gamma(g_{m1} + g_{m2})$. The noise figure contribution from the transistors is inversely proportional to the total transconductance $(g_{m1} + g_{m2})$. To minimize this, **$g_{m1} + g_{m2}$ should be as large as possible**.\n\n**3. Optimization Strategy**\nCombining the impedance constraint and the noise minimization goals:\n\n*   **Maximize $R_F$:** A larger feedback resistor reduces the thermal noise injected by the resistor itself.\n*   **Maximize Gain ($A_v$):** To keep $R_{in} = 50 \\, \\Omega$ while increasing $R_F$, the gain $|A_v| \\approx (g_{m1} + g_{m2})R_{out}$ must increase.\n*   **Maximize Transconductance ($g_m$):** Increasing $g_{m1} + g_{m2}$ helps satisfy the gain requirement and directly reduces the transistor noise contribution to the NF. This can be done by increasing the bias current or increasing the transistor widths ($W$).\n*   **Maximize Output Resistance ($R_{out}$):** Increasing the output resistance (by using longer channel lengths $L$ for $M_1$ and $M_2$) increases the gain. This allows you to use a larger $R_F$ for a given $g_m$, or achieve the required gain with less $g_m$ (saving power).\n\n**Summary of Steps to Optimize NF:**\n1.  **Choose the largest possible feedback resistor $R_F$** to minimize its thermal noise contribution.\n2.  **Increase the transconductance ($g_{m1} + g_{m2}$)** by sizing the transistors wider or increasing the bias current. This reduces the transistor channel noise.\n3.  **Increase the output resistance ($r_{o1}, r_{o2}$)** by using longer channel lengths for the transistors. This increases the open-loop gain, which is necessary to maintain the $50 \\, \\Omega$ input match when using a large $R_F$.\n\nIdeally, you want to maximize the intrinsic gain ($g_m r_o$) of the transistors. This allows $R_F$ to be very large (minimizing resistor noise) while the high $g_m$ minimizes the transistor noise, all while satisfying $R_{in} = R_F / (1 + g_m r_o) = 50 \\, \\Omega$. In the limit where $R_F \\to \\infty$ and $g_m \\to \\infty$ (with their ratio fixed by the impedance match), the NF approaches 0 dB (theoretical minimum).",
        "format": "markdown",
        "sha256": "35efaf73617a95ac4107e19f926cbb01d59521f286b3be211ccbbfe82843f59d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly recommends increasing gm and RF together to preserve the 50-Ω match, using finite output resistance/high loop gain so gm can exceed 1/Rs and the NF can fall below 1+γ toward 0 dB. The input-resistance expression is a high-gain approximation to the finite-ro relation, but it supports the correct optimization direction.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 16576,
        "total_tokens": 18608,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15535,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 16576,
        "total_tokens": 18608,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 15535,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the Noise Figure (NF) of the circuit shown (a resistive feedback amplifier using a CMOS inverter configuration) while maintaining an input resistance $R_{in} = 50 \\, \\Omega$, we need to analyze the input impedance and noise contributions of the components.\n\n### 1. Analysis of Input Impedance ($R_{in}$)\nThis circuit is a shunt-shunt feedback amplifier. The input impedance looking into the node after $C_1$ is approximately given by:\n$$R_{in} \\approx \\frac{R_F}{1 + |A_v|}$$\nwhere $A_v$ is the open-loop voltage gain of the CMOS inverter stage.\nThe gain $A_v$ is approximately:\n$$A_v \\approx -(g_{m1} + g_{m2}) (r_{o1} \\parallel r_{o2} \\parallel R_F)$$\nAssuming the loop gain is high ($|A_v| \\gg 1$) and $R_F$ is large compared to the output impedance, the input impedance simplifies to:\n$$R_{in} \\approx \\frac{1}{g_{m1} + g_{m2}}$$\n\n**Constraint:** To match $R_{in} = 50 \\, \\Omega$, we must set the total transconductance:\n$$g_{m1} + g_{m2} = \\frac{1}{50 \\, \\Omega} = 20 \\, \\text{mS}$$\n\n### 2. Analysis of Noise Figure (NF)\nThe total Noise Figure is determined by the noise contributions of the transistors ($M_1, M_2$) and the feedback resistor ($R_F$).\n*   **Transistor Noise:** The input-referred noise voltage squared due to the transistors is $\\overline{V_{n,M}^2} \\approx \\frac{4kT\\gamma}{g_{m1} + g_{m2}}$. Since $g_{m1} + g_{m2} = 1/R_{in} = 1/R_S$ (where $R_S=50\\Omega$ is the source resistance), the noise factor contribution from the transistors is roughly $\\gamma$ (the channel noise coefficient).\n*   **Resistor Noise:** The feedback resistor $R_F$ contributes thermal noise. Its contribution to the Noise Figure is inversely proportional to $R_F$ (approximately $\\frac{R_S}{R_F}$).\n\nThe approximate Noise Figure is:\n$$NF \\approx 1 + \\gamma + \\frac{R_S}{R_F}$$\n\n### 3. Optimization Steps\nTo minimize the NF, we must minimize $\\gamma$ and the term $\\frac{R_S}{R_F}$.\n\n**Step 1: Maximize $R_F$**\n*   To minimize the noise contribution from the feedback resistor, **$R_F$ should be as large as possible**.\n*   However, we must maintain $R_{in} = 50 \\, \\Omega$. From the equation $R_{in} \\approx \\frac{R_F}{1 + |A_v|}$, if we increase $R_F$, we must proportionally increase the gain $|A_v|$.\n\n**Step 2: Maximize Voltage Gain ($|A_v|$) via Output Impedance**\n*   Since $g_{m1} + g_{m2}$ is fixed at 20 mS, the only way to increase gain $|A_v| \\approx (g_{m1} + g_{m2})R_{out}$ is to increase the output resistance $R_{out} = r_{o1} \\parallel r_{o2}$.\n*   **Use long channel lengths ($L$) for $M_1$ and $M_2$.** The output resistance $r_o$ is proportional to channel length ($r_o \\propto L$). Long channels will provide the high gain needed to support a large $R_F$.\n\n**Step 3: Minimize Channel Noise Coefficient ($\\gamma$)**\n*   The parameter $\\gamma$ represents excess thermal noise in the channel. For long-channel devices, $\\gamma \\approx 2/3$. For short-channel devices, $\\gamma$ can be much larger (2 to 4).\n*   **Use long channel lengths ($L$) for $M_1$ and $M_2$** to keep $\\gamma$ close to the theoretical minimum of 2/3.\n\n**Step 4: Transistor Sizing ($W/L$)**\n*   You need to achieve $g_{m1} + g_{m2} = 20$ mS.\n*   Since $M_2$ is a PMOS device, it has lower mobility ($\\mu_p < \\mu_n$) than the NMOS $M_1$. To contribute equally to the transconductance (or to balance the design), $M_2$ typically needs a larger width ($W_2 > W_1$).\n*   Adjust the bias current $I_D$ and widths $W$ to achieve the target $g_m$ while keeping the devices in saturation.\n\n### Summary\nTo optimize for NF with $R_{in} = 50 \\, \\Omega$:\n1.  Set **$g_{m1} + g_{m2} = 20$ mS**.\n2.  Use **long channel lengths** for both transistors to minimize $\\gamma$ and maximize output resistance $r_o$.\n3.  Choose **$R_F$ as large as possible**. The high output resistance from the long channels will allow for high gain, which keeps $R_{in}$ at 50 $\\Omega$ even with a large $R_F$, thereby minimizing the resistor's noise contribution.",
        "format": "markdown",
        "sha256": "e43a80fb33646826a5396029599452670b617fccd327638cbb45f9fac137e660"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer fixes total gm at 1/Rs by assuming Rin ≈ 1/gm and therefore misses the key optimization: finite ro permits gm > 1/Rs while RF is increased to maintain the 50 Ω match, allowing NF below 1 + γ. Increasing ro and RF at fixed gm does not establish that result.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 10751,
        "total_tokens": 12783,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9495,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 10751,
        "total_tokens": 12783,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9495,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-016-optimize-for-nf-rin-must-remain-equal",
      "part": "part2",
      "question_number": 16,
      "question": "How do we optimize the circuit shown in the figure for the NF if Rin must remain equal to 50 Ohm?",
      "figures": [
        "tasks/part2-016-optimize-for-nf-rin-must-remain-equal/figure-13.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To optimize the Noise Figure (NF) of the circuit shown (a resistive feedback amplifier, often used as a wideband LNA) while maintaining an input impedance $R_{in} = 50 \\, \\Omega$, we need to analyze the relationship between the input impedance, the gain, and the noise sources.\n\n**1. Analysis of Input Impedance ($R_{in}$)**\nThe circuit consists of a CMOS inverter ($M_1$ and $M_2$) with a shunt-shunt feedback resistor $R_F$.\nThe input impedance looking into the amplifier (ignoring the coupling capacitor $C_1$) is determined by the Miller effect of the feedback resistor $R_F$. For an inverting amplifier with open-loop voltage gain $A_v$ (where $A_v$ is negative, so let's use magnitude $|A_v|$), the input resistance is approximately:\n$$R_{in} \\approx \\frac{R_F}{1 + |A_v|}$$\nThe open-loop gain $|A_v|$ is given by the total transconductance ($G_m = g_{m1} + g_{m2}$) multiplied by the output resistance ($R_{out} = r_{o1} \\parallel r_{o2}$):\n$$|A_v| \\approx (g_{m1} + g_{m2})(r_{o1} \\parallel r_{o2})$$\n\nGiven the constraint **$R_{in} = 50 \\, \\Omega$**, we have:\n$$50 \\approx \\frac{R_F}{1 + |A_v|} \\implies R_F \\approx 50(1 + |A_v|)$$\nThis tells us that to maintain a $50 \\, \\Omega$ input match, the feedback resistor $R_F$ must be proportional to the amplifier's gain.\n\n**2. Analysis of Noise Figure (NF)**\nThe main noise sources in this circuit are:\n*   Thermal noise of the source resistance ($R_S = 50 \\, \\Omega$).\n*   Thermal noise of the feedback resistor $R_F$.\n*   Channel thermal noise of transistors $M_1$ and $M_2$.\n\nThe Noise Figure ($F$) can be approximated as:\n$$NF \\approx 1 + \\frac{4 R_S}{R_F} + \\frac{\\gamma}{g_{m,total} R_S}$$\n*(Note: This is a simplified expression assuming high gain, where the noise of $R_F$ is the dominant resistor noise and $\\gamma$ is the transistor noise coefficient).*\n\n**3. Optimization Strategy**\nSubstitute the expression for $R_F$ ($R_F \\approx 50 |A_v|$) into the NF equation (assuming $|A_v| \\gg 1$):\n$$NF \\approx 1 + \\frac{4 R_S}{50 |A_v|} + \\frac{\\gamma}{(g_{m1} + g_{m2}) R_S}$$\nSince $R_S = 50 \\, \\Omega$:\n$$NF \\approx 1 + \\frac{4}{|A_v|} + \\frac{\\gamma}{50 (g_{m1} + g_{m2})}$$\n\nTo minimize the NF, we need to minimize the added noise terms. This leads to two main conclusions:\n\n1.  **Maximize the Open-Loop Gain ($|A_v|$):**\n    *   Looking at the term $\\frac{4}{|A_v|}$, increasing the gain reduces the noise contribution of the feedback resistor $R_F$.\n    *   Because $R_{in}$ is fixed at $50 \\, \\Omega$, a higher gain allows us to use a **larger $R_F$** ($R_F \\approx 50 |A_v|$). A larger resistor generates less thermal noise current ($4kT/R_F$), thereby improving the NF.\n\n2.  **Maximize the Transconductance ($g_{m1} + g_{m2}$):**\n    *   Looking at the term $\\frac{\\gamma}{50 (g_{m1} + g_{m2})}$, increasing the total transconductance reduces the noise contribution of the transistors.\n\n**Practical Steps to Optimize:**\n*   **Increase Channel Length ($L$):** Use longer channel lengths for $M_1$ and $M_2$. This increases the output resistance ($r_{o1}, r_{o2}$), which significantly boosts the open-loop gain $|A_v|$. This allows you to increase $R_F$ while keeping $R_{in} = 50 \\, \\Omega$, suppressing the noise from the feedback resistor.\n*   **Increase Transistor Width ($W$):** Increase the width of $M_1$ and $M_2$ to increase $g_m$. This directly reduces the transistor channel noise.\n*   **Increase $R_F$:** As a result of increasing the gain (via $L$ and $W$), you must increase the value of $R_F$ proportionally to maintain the $50 \\, \\Omega$ input match.\n\n**Summary:**\nTo optimize the NF, you should **maximize the gain of the core inverter stage ($M_1, M_2$)** by using long-channel devices (high $r_o$) and sufficient width (high $g_m$). This allows you to use a **large feedback resistor $R_F$**, which minimizes the noise contribution of the feedback network while satisfying the $R_{in} = 50 \\, \\Omega$ constraint.",
        "format": "markdown",
        "sha256": "b3ca920027bbe6ff33267d3a003c41f33ffd7267d693bca05dc2ba351548cb7d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "It correctly recommends increasing gm and RF together to reduce noise while preserving the 50 Ω match. Although its input-resistance and noise equations are approximate and omit the exact finite-ro relation, the matched gm/RF optimization is accepted by the golden full-credit rule.",
          "golden_solution_sha256": "6801650fd2054e7d374317849fcda2881c563a35f3d14b44d310d3d32f91b1cd",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 10335,
        "total_tokens": 12367,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2032,
        "output_tokens": 10335,
        "total_tokens": 12367,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 9123,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance of the circuit, we need to analyze the small-signal equivalent circuit, particularly focusing on the feedback network.\n\n**1. Circuit Analysis and Topology**\n*   The circuit consists of an input node $P$ connected to the gate of transistor $M_1$.\n*   There is a feedback resistor $R_F$ connecting the output node $V_{out}$ to the input node $P$.\n*   This configuration represents **shunt-shunt feedback** (voltage-current feedback), which is typical for transimpedance amplifiers. This type of feedback lowers the input impedance.\n\n**2. Small-Signal Gain Calculation**\nLet's determine the open-loop voltage gain $A_v = \\frac{v_{out}}{v_p}$ from the input node $P$ to the output node $V_{out}$.\n*   **Stage 1 ($M_1$):** $M_1$ is a common-source amplifier. The voltage at node $X$ (drain of $M_1$) is given by:\n    $$v_x = -g_{m1} R_{D1} v_p$$\n    (Assuming the impedance at node $X$ is dominated by $R_{D1}$ and the gate of $M_2$ is high impedance).\n\n*   **Stage 2 ($M_2, M_3$):** The transistors $M_2$ and $M_3$ along with the current source $I_{SS}$ form a second gain stage.\n    *   Looking at the topology, if we assume $M_2$ and $M_3$ act as a current mirror or active load stage that converts the voltage $v_x$ to an output current/voltage.\n    *   For the circuit to be stable with negative feedback (resistor from output to input), the overall gain $A_v$ must be negative (inverting).\n    *   Let's assume the second stage provides a gain $A_2$. A plausible interpretation is that $M_2$ acts as a common-source stage (inverting) or part of a cascode. However, a common configuration for such a block is a current mirror load where the signal is inverted again or passed through.\n    *   If we assume the standard inverting amplifier behavior for the whole chain:\n        $$v_{out} = A_v v_p$$\n    *   Based on the components, a likely gain expression (assuming $M_2, M_3$ provide a gain stage with effective transconductance and load $R_{D2}$) is:\n        $$A_v \\approx -g_{m1} R_{D1} (g_{m2} R_{D2})$$\n        (Note: The exact gain depends on the specific operation region of $M_2$ and $M_3$, but it is a large negative value, $A_v \\ll -1$).\n\n**3. Input Impedance Calculation (Miller Effect)**\nThe input impedance is determined by the parallel combination of the capacitor $C_{in}$ and the effective resistance looking into the node $P$.\n*   The resistor $R_F$ is connected between $P$ (voltage $v_p$) and $V_{out}$ (voltage $A_v v_p$).\n*   The current flowing through $R_F$ from the input is:\n    $$i_F = \\frac{v_p - v_{out}}{R_F} = \\frac{v_p - A_v v_p}{R_F} = \\frac{v_p (1 - A_v)}{R_F}$$\n*   The effective input resistance $R_{in}$ (labeled in the diagram) looking into the gate of $M_1$ is:\n    $$R_{in} = \\frac{v_p}{i_F} = \\frac{R_F}{1 - A_v}$$\n*   Since the amplifier is inverting ($A_v$ is negative), let $A_v = -|A_v|$. Then:\n    $$R_{in} = \\frac{R_F}{1 + |A_v|}$$\n    If the gain $|A_v|$ is large ($|A_v| \\gg 1$), then $R_{in} \\approx \\frac{R_F}{|A_v|}$.\n\n**4. Total Input Impedance**\nThe total input impedance $Z_{in}$ includes the capacitor $C_{in}$ in parallel with the effective resistance $R_{in}$.\n$$Z_{in} = R_{in} \\parallel \\frac{1}{s C_{in}} = \\frac{1}{s C_{in} + \\frac{1}{R_{in}}}$$\nSubstituting $R_{in}$:\n$$Z_{in} = \\frac{1}{s C_{in} + \\frac{1 - A_v}{R_F}}$$\n\n**Summary**\nThe input impedance is dominated by the Miller effect of the feedback resistor $R_F$.\n$$Z_{in} = \\frac{1}{s C_{in}} \\parallel \\left( \\frac{R_F}{1 - A_v} \\right)$$\nwhere $A_v = \\frac{v_{out}}{v_p}$ is the voltage gain from the gate of $M_1$ to $V_{out}$. Assuming a high gain inverting amplifier ($A_v \\ll 0$), the resistive part is approximately $\\frac{R_F}{|A_v|}$.\n\nIf we assume the gain is $A_v \\approx -g_{m1} g_{m2} R_{D1} R_{D2}$ (based on a two-stage cascade interpretation), then:\n$$R_{in} \\approx \\frac{R_F}{g_{m1} g_{m2} R_{D1} R_{D2}}$$\nAnd the total input impedance is:\n$$Z_{in} = \\frac{1}{s C_{in} + \\frac{1 + g_{m1} g_{m2} R_{D1} R_{D2}}{R_F}}$$",
        "format": "markdown",
        "sha256": "cf56a04f5aa704bd0b1a5bd246ea86485eb8d6286e1c4c26e6c7d93020842571"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies shunt feedback and the general Miller reduction of input resistance, but misses the exact output-side resistance term: the result should be (RF + RD2)/(1 + A0). Its gain expression is also not the specified unloaded gain.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 28300,
        "total_tokens": 28483,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26977,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 28300,
        "total_tokens": 28483,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 26977,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance of the circuit, we need to analyze the small-signal behavior of the amplifier. The circuit consists of an input stage with a feedback resistor $R_F$, which suggests a shunt-shunt feedback topology (transimpedance amplifier).\n\n**1. Circuit Analysis and Gain Calculation**\n\nLet $v_p$ be the small-signal voltage at the input node $P$ and $v_{out}$ be the voltage at the output node.\n\n*   **Stage 1 ($M_1$):** $M_1$ is a common-source amplifier. The input is at the gate ($P$) and the output is at the drain ($X$).\n    The small-signal voltage at $X$ is:\n    $$v_x = -g_{m1} R_{D1} v_p$$\n    (Assuming the input impedance of the next stage is very high).\n\n*   **Stage 2 ($M_2, M_3$):** The transistors $M_2$ and $M_3$ are connected to the current source $I_{SS}$ which is tied to $V_{DD}$. This configuration indicates that $M_2$ and $M_3$ form a PMOS differential pair (sources connected to the tail current source node).\n    *   The gate of $M_2$ is connected to $X$.\n    *   The gate of $M_3$ is connected to a bias voltage $V_b$ (AC ground).\n    *   The drain of $M_2$ is grounded.\n    *   The drain of $M_3$ is the output node $V_{out}$.\n\n    This is a differential pair with single-ended input ($v_x$) and single-ended output ($v_{out}$). The effective transconductance of this stage is $G_m = \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}$.\n    The current flowing into the output node from the differential pair is determined by the input voltage $v_x$. Since $v_x$ is applied to $M_2$ and $M_3$ gate is grounded:\n    $$i_{out} = G_m (0 - v_x) \\times (-1) \\text{ (direction consideration)}$$\n    More simply, a change in $v_x$ steers current. If $v_x$ decreases, $M_2$ conducts more, $M_3$ conducts less. Since $M_3$ pulls current from $V_{DD}$ to $V_{out}$ (PMOS source to drain), a decrease in $M_3$ current leads to a decrease in $V_{out}$.\n    The voltage gain from $X$ to $V_{out}$ is:\n    $$\\frac{v_{out}}{v_x} = - G_m (R_{D2} || R_F) = - \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}} (R_{D2} || R_F)$$\n    (Note: $R_F$ appears in parallel with $R_{D2}$ at the output node for the gain calculation).\n\n*   **Total Open-Loop Gain ($A_v$):**\n    Combining the stages:\n    $$A_v = \\frac{v_{out}}{v_p} = \\frac{v_{out}}{v_x} \\cdot \\frac{v_x}{v_p} = \\left[ - \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}} (R_{D2} || R_F) \\right] \\cdot [ -g_{m1} R_{D1} ]$$\n    $$A_v = g_{m1} R_{D1} (R_{D2} || R_F) \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}$$\n    Wait, let's check the sign again.\n    $v_p \\uparrow \\Rightarrow v_x \\downarrow$ (inverting).\n    $v_x \\downarrow$ (at PMOS gate) $\\Rightarrow V_{SG2} \\uparrow \\Rightarrow I_{D2} \\uparrow \\Rightarrow I_{D3} \\downarrow$.\n    $I_{D3} \\downarrow$ (current into $R_{D2}$) $\\Rightarrow v_{out} \\downarrow$.\n    So $v_p \\uparrow \\Rightarrow v_{out} \\downarrow$. The total gain $A_v$ is negative.\n    $$A_v = - g_{m1} R_{D1} (R_{D2} || R_F) \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}$$\n\n**2. Input Impedance Calculation**\n\nThe input impedance $Z_{in}$ is determined by the parallel combination of the capacitor $C_{in}$ and the equivalent resistance due to the feedback resistor $R_F$ (Miller effect).\n\nThe current $I_{in}$ entering node $P$ splits into the capacitor $C_{in}$ and the feedback resistor $R_F$:\n$$I_{in} = I_{C_{in}} + I_{R_F} = s C_{in} v_p + \\frac{v_p - v_{out}}{R_F}$$\n$$I_{in} = v_p \\left( s C_{in} + \\frac{1 - A_v}{R_F} \\right)$$\n\nThe input impedance $Z_{in} = v_p / I_{in}$ is:\n$$Z_{in} = \\frac{1}{s C_{in} + \\frac{1 - A_v}{R_F}}$$\n\nThis can be viewed as the parallel combination of $C_{in}$ and an equivalent input resistance $R_{in}$:\n$$R_{in} = \\frac{R_F}{1 - A_v}$$\n\nSince $A_v$ is negative and typically large in magnitude ($|A_v| \\gg 1$), $1 - A_v \\approx 1 + |A_v| \\approx |A_v|$.\n$$R_{in} \\approx \\frac{R_F}{|A_v|} = \\frac{R_F}{g_{m1} R_{D1} (R_{D2} || R_F) \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}}$$\n\nIf we assume $R_F \\gg R_{D2}$, then $R_{D2} || R_F \\approx R_{D2}$, and:\n$$R_{in} \\approx \\frac{R_F}{g_{m1} R_{D1} R_{D2} \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}}$$\n\n**Final Answer:**\nThe input impedance $Z_{in}$ is given by:\n$$Z_{in} = \\left( s C_{in} + \\frac{1 - A_v}{R_F} \\right)^{-1}$$\nwhere the voltage gain $A_v$ is:\n$$A_v = - g_{m1} R_{D1} (R_{D2} || R_F) \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}$$\nThe resistive part labeled $R_{in}$ in the diagram corresponds to:\n$$R_{in} = \\frac{R_F}{1 - A_v} \\approx \\frac{R_F}{g_{m1} R_{D1} (R_{D2} || R_F) \\frac{g_{m2}g_{m3}}{g_{m2}+g_{m3}}}$$",
        "format": "markdown",
        "sha256": "d7f6f40e184e8359caeff28060b2ad1e4badcca34a9a9404071bf9e27b6847b9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "It correctly identifies feedback/Miller action and the low input resistance, but uses a loaded gain with RD2||RF and omits the output-side resistance in the exact result. The required expression is Rin = (RF + RD2)/(1 + A0), with A0 defined as the unloaded amplifier gain; its stage-gain estimate is also not equivalent to that A0.",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 27117,
        "total_tokens": 27300,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25397,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 27117,
        "total_tokens": 27300,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 25397,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-017-compute-input-impedance",
      "part": "part2",
      "question_number": 17,
      "question": "Compute the input impedance of the circuit in the figure.",
      "figures": [
        "tasks/part2-017-compute-input-impedance/figure-14.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the input impedance of the circuit, we need to determine the equivalent impedance looking into the input node $P$. The circuit employs a feedback resistor $R_F$ connecting the output $V_{out}$ to the input $P$. This is a shunt-shunt feedback configuration.\n\n**1. Determine the Voltage Gain ($A_v$)**\n\nFirst, we analyze the small-signal voltage gain from the input node $P$ to the output node $V_{out}$. Let $v_p$ be the small-signal voltage at node $P$.\n\n*   **Stage 1 ($M_1$):** $M_1$ is a common-source amplifier. The voltage at node $X$ (drain of $M_1$) is:\n    $$v_x = -g_{m1} R_{D1} v_p$$\n    (assuming the input impedance of the next stage is high).\n\n*   **Stage 2 ($M_2$ and $M_3$):** The transistors $M_2$ and $M_3$ are connected to a constant current source $I_{SS}$. Thus, the sum of their drain currents is constant: $I_{D2} + I_{D3} = I_{SS}$. In small-signal terms, the changes in current must sum to zero:\n    $$i_{d2} + i_{d3} = 0 \\implies i_{d3} = -i_{d2}$$\n    \n    For $M_2$ (common-source with source grounded):\n    $$i_{d2} = g_{m2} v_x$$\n    \n    For $M_3$, the gate is connected to a constant bias $V_b$ (AC ground), and the source is at $V_{out}$. The gate-source voltage is $v_{gs3} = 0 - v_{out} = -v_{out}$. The drain current is:\n    $$i_{d3} = g_{m3} v_{gs3} = -g_{m3} v_{out}$$\n    (Note: This assumes the impedance at the common drain node is high enough that the current is primarily determined by the transconductance).\n\n    Equating the currents:\n    $$-g_{m3} v_{out} = -g_{m2} v_x \\implies v_{out} = \\frac{g_{m2}}{g_{m3}} v_x$$\n\n*   **Total Gain:** Substituting $v_x$:\n    $$v_{out} = \\frac{g_{m2}}{g_{m3}} (-g_{m1} R_{D1} v_p) = -\\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}} v_p$$\n    So, the voltage gain $A_v = \\frac{v_{out}}{v_p} = -\\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}}$.\n\n**2. Compute Input Impedance ($R_{in}$)**\n\nThe input impedance is determined by the feedback resistor $R_F$ and the Miller effect. The gate of $M_1$ draws no current (infinite impedance). Therefore, the input current $i_{in}$ flows entirely through $R_F$.\n\n$$i_{in} = \\frac{v_p - v_{out}}{R_F} = \\frac{v_p - A_v v_p}{R_F} = \\frac{v_p (1 - A_v)}{R_F}$$\n\nThe input resistance $R_{in}$ (looking into node $P$) is:\n$$R_{in} = \\frac{v_p}{i_{in}} = \\frac{R_F}{1 - A_v}$$\n\nSubstituting the expression for $A_v$:\n$$R_{in} = \\frac{R_F}{1 - \\left( -\\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}} \\right)} = \\frac{R_F}{1 + \\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}}}$$\n\nIf the loop gain is large ($\\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}} \\gg 1$), the input impedance can be approximated as:\n$$R_{in} \\approx \\frac{R_F g_{m3}}{g_{m1} g_{m2} R_{D1}}$$\n\nConsidering the capacitor $C_{in}$ in parallel with the input, the total input impedance $Z_{in}$ would be:\n$$Z_{in} = R_{in} \\parallel \\frac{1}{s C_{in}} = \\left( \\frac{R_F}{1 + \\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}}} \\right) \\parallel \\frac{1}{s C_{in}}$$\n\nHowever, typically the label $R_{in}$ refers to the equivalent resistance of the amplifier input.\n\n**Answer:**\nThe input impedance is approximately:\n$$R_{in} = \\frac{R_F}{1 + \\frac{g_{m1} g_{m2} R_{D1}}{g_{m3}}}$$\n(or $Z_{in} = R_{in} || \\frac{1}{sC_{in}}$ if the capacitor is included).",
        "format": "markdown",
        "sha256": "e6dec81bc12999a47724596144c3b9b2bb6fbea65d95cfd42be10ee627364abe"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "It recognizes that feedback through RF reduces the input resistance, but its M2/M3 gain analysis is incorrect and omits the output resistance RD2. The result RF/(1+...) misses the required exact expression (RF+RD2)/(1+A0).",
          "golden_solution_sha256": "d478f09ce99c16f2ada89711c88d0564aa20ae775a06fad0c89d6658dc32fb99",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 25297,
        "total_tokens": 25480,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24089,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 183,
        "output_tokens": 25297,
        "total_tokens": 25480,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 24089,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise resulting from the LDO's thermal noise $S_{th}$, we need to analyze how noise on the supply voltage ($V_{out}$) translates to phase fluctuations at the oscillator output. This phenomenon is known as **supply pushing**.\n\nHere is the step-by-step computation:\n\n### 1. Identify the Noise Transfer Mechanism\nThe LDO regulator produces an output voltage $V_{out}$ which powers the VCO. The thermal noise of the LDO, represented by a voltage noise spectral density $S_{th}$ (in $V^2/Hz$), appears directly on the supply rail $V_{out}$.\n\nIn the given circuit:\n*   The inductors $L_1$ act as DC shorts, so the DC voltage at the tank nodes $X$ and $Y$ is approximately equal to $V_{out}$.\n*   The varactors $M_{v1}$ and $M_{v2}$ (and the parasitic capacitances of transistors $M_1, M_2$) are connected to these nodes. Their capacitance depends on the voltage across them.\n*   Therefore, a fluctuation in $V_{out}$ changes the reverse bias voltage across the varactors, modulating their capacitance ($C_v$).\n*   Since the oscillation frequency $\\omega_0$ is determined by the tank inductance and capacitance ($\\omega_0 \\approx 1/\\sqrt{L C_{total}}$), a change in capacitance leads to a change in frequency.\n\n### 2. Define the Supply Pushing Factor ($K_{supply}$)\nWe define a sensitivity factor, often called the supply pushing gain, which relates changes in supply voltage to changes in oscillation frequency:\n\n$$K_{supply} = \\frac{\\partial \\omega_{out}}{\\partial V_{out}} \\quad \\text{[rad/s/V]}$$\n\nAlternatively, in Hz/V:\n$$K_{supply, Hz} = \\frac{\\partial f_{out}}{\\partial V_{out}}$$\n\nThis factor can be determined by simulating the VCO frequency while sweeping the supply voltage $V_{out}$.\n\n### 3. Relate Voltage Noise to Frequency Noise\nThe noise voltage $v_n(t)$ from the LDO causes an instantaneous frequency deviation $\\Delta \\omega(t)$:\n$$\\Delta \\omega(t) = K_{supply} \\cdot v_n(t)$$\n\nThe spectral density of this frequency noise, $S_{\\Delta \\omega}(f)$, is:\n$$S_{\\Delta \\omega}(f) = K_{supply}^2 \\cdot S_{th}(f)$$\n\n### 4. Convert Frequency Noise to Phase Noise\nPhase $\\phi(t)$ is the time integral of frequency $\\omega(t)$. In the frequency domain, integration corresponds to division by $j\\omega$ (where $\\omega = 2\\pi f_{offset}$ is the angular offset frequency from the carrier).\n\n$$\\phi(t) = \\int \\Delta \\omega(t) dt$$\n\nTaking the spectral density relationship (magnitude squared of the transfer function $1/j\\omega$):\n$$S_{\\phi}(f_{offset}) = \\frac{S_{\\Delta \\omega}(f_{offset})}{(2\\pi f_{offset})^2}$$\n\n### 5. Final Formula\nSubstituting the expression for frequency noise, we get the VCO output phase noise spectral density $S_{\\phi}(f_{offset})$:\n\n$$S_{\\phi}(f_{offset}) = \\frac{K_{supply}^2}{(2\\pi f_{offset})^2} S_{th}$$\n\nOr, using the pushing factor in Hz/V ($K_{supply, Hz}$):\n\n$$S_{\\phi}(f_{offset}) = \\frac{K_{supply, Hz}^2}{f_{offset}^2} S_{th}$$\n\n**Summary:**\nThe LDO thermal noise (which is typically white/flat) gets converted into frequency noise via the supply pushing effect. This frequency noise is then integrated to become phase noise, resulting in a **$1/f^2$** (or -20 dB/decade) slope in the phase noise spectrum close to the carrier.",
        "format": "markdown",
        "sha256": "7e2640af11f6b36021ac738ba4ca858b2c485cf4c60791be12a594ba39c0943c"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies supply pushing and derives the frequency-noise-to-phase-noise conversion with the expected 1/offset-frequency-squared dependence. It explains the direct varactor mechanism, but omits the explicit design insight that reducing KVCO reduces this noise conversion.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 6094,
        "total_tokens": 8641,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5178,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 6094,
        "total_tokens": 8641,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5178,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise caused by the LDO thermal noise $S_{th}$, we need to analyze how the supply voltage noise transfers to the oscillator's phase. This phenomenon is known as **supply pushing** or **AM-to-PM conversion**.\n\nHere is the step-by-step computation:\n\n### 1. Identify the Noise Transfer Mechanism\nThe LDO regulator produces an output voltage $V_{out}$ which powers the VCO. The thermal noise of the LDO, with spectrum $S_{th}$ (in $V^2/Hz$), appears as voltage fluctuations on the supply rail $V_{out}$.\n\nLooking at the schematic, the oscillation frequency is determined by the LC tank ($L_1$ and the capacitor banks/varactors). The varactors $M_{v1}$ and $M_{v2}$ (and potentially the switched capacitors in $B_1, B_2$) are voltage-dependent capacitors.\n*   The gates of $M_{v1}$ and $M_{v2}$ are connected to the oscillator nodes $X$ and $Y$.\n*   The DC voltage at nodes $X$ and $Y$ is approximately $V_{out}$ (since the inductors $L_1$ act as DC shorts).\n*   The other terminals of the varactors are connected to the control voltage $V_{cont}$.\n\nTherefore, the reverse bias voltage across the varactors is $V_{bias} \\approx V_{out} - V_{cont}$. Any noise on $V_{out}$ directly modulates this bias voltage, changing the capacitance, and thus modulating the oscillation frequency.\n\n### 2. Determine the Supply Pushing Factor ($K_{VDD}$)\nWe define the sensitivity of the oscillation frequency $\\omega_{osc}$ to the supply voltage $V_{out}$ as $K_{VDD}$:\n$$K_{VDD} = \\frac{\\partial \\omega_{osc}}{\\partial V_{out}}$$\n\nSince the bias voltage is $V_{out} - V_{cont}$, an increase in $V_{out}$ has the exact same effect on the varactor capacitance as a decrease in $V_{cont}$. Therefore, the magnitude of the supply sensitivity is approximately equal to the VCO tuning gain ($K_{VCO}$):\n$$|K_{VDD}| \\approx |K_{VCO}| = \\left| \\frac{\\partial \\omega_{osc}}{\\partial V_{cont}} \\right|$$\n\n*(Note: If $K_{VCO}$ is given in Hz/V, then $K_{VDD}$ is also in Hz/V. If in rad/s/V, then $K_{VDD}$ is in rad/s/V).*\n\n### 3. Calculate Frequency Noise Spectrum\nThe voltage noise $S_{th}$ is converted into frequency noise. The spectral density of the frequency fluctuations $S_{\\Delta f}(f)$ (in $Hz^2/Hz$) is:\n$$S_{\\Delta f}(f_{offset}) = K_{VCO}^2 \\cdot S_{th}(f_{offset})$$\n*(Assuming $K_{VCO}$ is in Hz/V)*.\n\n### 4. Convert Frequency Noise to Phase Noise\nPhase is the time integral of frequency ($\\phi(t) = 2\\pi \\int \\Delta f(t) dt$). In the frequency domain, integration corresponds to dividing the power spectral density by $(2\\pi f_{offset})^2$ (or simply $f_{offset}^2$ if working with Hz directly for the phase variance).\n\nThe phase noise spectral density $S_{\\phi}(f_{offset})$ (in $rad^2/Hz$) is:\n$$S_{\\phi}(f_{offset}) = \\frac{S_{\\Delta f}(f_{offset})}{f_{offset}^2} = \\frac{K_{VCO}^2 \\cdot S_{th}(f_{offset})}{f_{offset}^2}$$\n\n### 5. Final Result: Single-Sideband Phase Noise $\\mathcal{L}(f_{offset})$\nThe standard metric for phase noise, $\\mathcal{L}(f_{offset})$, is defined as half of the phase noise spectral density (single-sideband).\n\n$$ \\mathcal{L}(f_{offset}) = \\frac{1}{2} S_{\\phi}(f_{offset}) = \\frac{K_{VCO}^2 \\cdot S_{th}(f_{offset})}{2 f_{offset}^2} $$\n\n**Summary Formula:**\nIf $K_{VCO}$ is the VCO gain in **Hz/V** and $S_{th}$ is the LDO noise in **$V^2/Hz$**:\n$$ \\mathcal{L}(f_{offset}) \\approx \\frac{K_{VCO}^2 S_{th}}{2 f_{offset}^2} $$\n\nThis shows that the phase noise due to supply noise falls off at **20 dB/decade** (proportional to $1/f^2$) and is directly proportional to the square of the VCO gain ($K_{VCO}^2$). This is why low-noise LDOs and low-gain VCO designs are critical for low phase noise.",
        "format": "markdown",
        "sha256": "5bf3650b5ce62e1816dd952adcc0c733e41797f636bc26088ac661173af1d6ed"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 4,
          "is_full_credit": true,
          "rationale": "Correctly identifies supply pushing through the varactors, relates Kpush to KVCO, and converts the resulting frequency noise to SSB phase noise with the correct 1/f_offset² dependence. The AM-to-PM wording is imprecise, but the derivation uses the correct frequency-to-phase conversion.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 7069,
        "total_tokens": 9616,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5927,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 7069,
        "total_tokens": 9616,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5927,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 4,
        "score_percent": 100,
        "is_full_credit": true
      }
    },
    {
      "question_id": "part2-018-ldo-regulator-generates-thermal-noise-with-spectrum",
      "part": "part2",
      "question_number": 18,
      "question": "If the LDO regulator in the figure generates thermal noise with spectrum Sth, how do we compute the VCO output phase noise?",
      "figures": [
        "tasks/part2-018-ldo-regulator-generates-thermal-noise-with-spectrum/figure-15.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "To compute the VCO output phase noise resulting from the LDO thermal noise $S_{th}$, we need to analyze how supply voltage noise translates into phase noise. This process involves a mechanism known as **supply pushing** (or $V_{DD}$ pushing).\n\nHere is the step-by-step computation:\n\n### 1. Identify the Noise Source and Mechanism\nThe LDO regulator generates thermal noise with a power spectral density $S_{th}$ (units: $V^2/Hz$). This noise appears as voltage fluctuations on the supply rail $V_{out}$.\n\nIn this LC VCO circuit, the supply voltage $V_{out}$ is connected to the top of the inductors $L_1$. Since inductors act as DC shorts, the DC common-mode voltage at nodes $X$ and $Y$ is approximately equal to $V_{out}$.\n\nThis common-mode voltage appears across the varactors ($M_{v1}$, $M_{v2}$) and the capacitor banks ($B_1$, $B_2$). Specifically, the voltage across the varactors is roughly $V_{out} - V_{cont}$. Therefore, any noise on $V_{out}$ modulates the capacitance of the varactors, which in turn modulates the oscillation frequency.\n\n### 2. Determine the \"Pushing Gain\" ($K_{push}$)\nWe first define the sensitivity of the VCO frequency to the supply voltage, often called the pushing gain, $K_{push}$ (units: rad/s/V).\n\nThe oscillation frequency is given by:\n$$ \\omega_{out} = \\frac{1}{\\sqrt{L_1 C_{total}}} $$\nwhere $C_{total}$ is the total tank capacitance, which includes the varactor capacitance $C_{var}$. Since the varactor capacitance depends on the voltage across it ($V_{out} - V_{cont}$), we can find the sensitivity:\n\n$$ K_{push} = \\frac{\\partial \\omega_{out}}{\\partial V_{out}} = \\frac{\\partial \\omega_{out}}{\\partial C_{total}} \\cdot \\frac{\\partial C_{total}}{\\partial V_{out}} $$\n\nUsing the chain rule:\n$$ \\frac{\\partial \\omega_{out}}{\\partial C_{total}} = -\\frac{1}{2} \\frac{1}{\\sqrt{L_1} C_{total}^{3/2}} = -\\frac{\\omega_{out}}{2 C_{total}} $$\n$$ \\frac{\\partial C_{total}}{\\partial V_{out}} \\approx \\frac{\\partial C_{var}}{\\partial V} \\quad \\text{(slope of the varactor C-V curve)} $$\n\nSo, the pushing gain is:\n$$ K_{push} \\approx -\\frac{\\omega_{out}}{2 C_{total}} \\frac{\\partial C_{var}}{\\partial V} $$\n\n### 3. Convert Voltage Noise to Frequency Noise\nThe supply voltage noise $v_n(t)$ causes a frequency deviation $\\Delta \\omega(t) = K_{push} \\cdot v_n(t)$.\nConsequently, the spectral density of the frequency noise $S_{\\Delta \\omega}(f)$ is:\n$$ S_{\\Delta \\omega}(f) = K_{push}^2 \\cdot S_{th} $$\n\n### 4. Convert Frequency Noise to Phase Noise\nPhase $\\phi(t)$ is the time integral of frequency deviation $\\Delta \\omega(t)$. In the frequency domain (spectral density), integration corresponds to dividing by $\\omega^2$ (where $\\omega = 2\\pi f_{offset}$ is the offset frequency from the carrier).\n\nThe phase noise power spectral density $S_{\\phi}(f_{offset})$ is:\n$$ S_{\\phi}(f_{offset}) = \\frac{S_{\\Delta \\omega}(f_{offset})}{(2\\pi f_{offset})^2} = \\frac{K_{push}^2 \\cdot S_{th}}{(2\\pi f_{offset})^2} $$\n\n### 5. Final Phase Noise Calculation ($\\mathcal{L}$)\nThe single-sideband phase noise $\\mathcal{L}(f_{offset})$, typically expressed in dBc/Hz, is approximately half of the phase noise spectral density (for small phase deviations):\n\n$$ \\mathcal{L}(f_{offset}) \\approx \\frac{1}{2} S_{\\phi}(f_{offset}) = \\frac{K_{push}^2 \\cdot S_{th}}{2 (2\\pi f_{offset})^2} $$\n\n**Summary Formula:**\n$$ \\mathcal{L}(f_{offset}) = 10 \\log_{10} \\left( \\frac{1}{2} \\left( \\frac{\\partial \\omega_{out}}{\\partial V_{out}} \\right)^2 \\frac{S_{th}}{(2\\pi f_{offset})^2} \\right) \\text{ dBc/Hz} $$\n\nWhere $\\frac{\\partial \\omega_{out}}{\\partial V_{out}}$ is determined by the varactor sensitivity and tank parameters as derived in step 2.",
        "format": "markdown",
        "sha256": "91d2157903775fd25135857964f489c589b1315d5216d5407d3397cf5dc28313"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 3,
          "is_full_credit": false,
          "rationale": "Correctly identifies supply pushing, derives the frequency-noise conversion using Kpush, and applies FM-to-phase conversion with the expected 1/offset-frequency-squared dependence. It omits the explicit design insight that Kpush is closely related to KVCO and that reducing KVCO lowers this noise conversion.",
          "golden_solution_sha256": "f40f5d47fc68dc67261745b47ef8f93ebeabc96a5ea084c1e3fcf7bea12e1811",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 5410,
        "total_tokens": 7957,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4289,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2547,
        "output_tokens": 5410,
        "total_tokens": 7957,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4289,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 3,
        "score_percent": 75,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, which shows a cross-coupled LC oscillator with an added capacitor $C_T$ at the tail node $P$, here is the analysis of what happens to the phase noise:\n\n**The phase noise decreases (improves).**\n\nHere is the detailed explanation of why this happens:\n\n1.  **Filtering Tail Current Noise:** The tail current source $I_{SS}$ generates noise (both thermal noise and flicker/$1/f$ noise). This noise current flows into the impedance at the tail node $P$. Without the capacitor $C_T$, the impedance at this node is primarily the output resistance of the current source, which is typically high. This creates significant noise voltage fluctuations at node $P$. By adding $C_T$, you create a low-impedance path to ground for high-frequency noise components ($Z_{C_T} = 1/j\\omega C_T$). This shunts the noise current from the tail source to ground, preventing it from modulating the oscillator core.\n\n2.  **Suppressing the $2\\omega_0$ Voltage Swing:** In a differential cross-coupled oscillator, the tail node $P$ is a virtual ground for the fundamental oscillation frequency ($\\omega_0$). However, due to the switching action of the transistors $M_1$ and $M_2$, the voltage at node $P$ contains a large component at the second harmonic ($2\\omega_0$).\n    *   This large $2\\omega_0$ voltage swing modulates the non-linear parasitic capacitances of the transistors (like $C_{gs}$, $C_{db}$, etc.).\n    *   This modulation effectively changes the tank capacitance at twice the frequency, which can mix with the fundamental signal and cause frequency modulation (FM), leading to phase noise (a process known as AM-to-PM conversion).\n    *   Adding $C_T$ lowers the impedance at node $P$ specifically at $2\\omega_0$ and higher harmonics. This suppresses the voltage swing at the tail node, thereby reducing this modulation effect and the resulting phase noise.\n\n3.  **Reduction of $1/f$ Noise Upconversion:** The flicker noise ($1/f$ noise) from the tail current source is a major contributor to \"close-in\" phase noise (the $1/f^3$ region in the phase noise plot). The switching of the differential pair can upconvert this low-frequency noise to phase noise around the carrier. The capacitor $C_T$ helps to stabilize the tail node voltage and filter the noise currents, reducing this upconversion mechanism.\n\nIn summary, $C_T$ acts as a **tail filter**, reducing the impedance at the common source node for high-frequency noise and harmonics, which leads to a cleaner oscillation signal and **lower phase noise**.",
        "format": "markdown",
        "sha256": "dd0a688fd94c1bb2e1b311ff53c5854bb2b20689ad5e7d3ecd44079ed35d700d"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer claims a monotonic phase-noise improvement from filtering the tail node, missing the nonmonotonic effect and the class-C improvement and degradation mechanisms required by the golden solution.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 4955,
        "total_tokens": 7517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4352,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 4955,
        "total_tokens": 7517,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 4352,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, adding a capacitor $C_T$ to the tail node $P$ generally **decreases (improves) the phase noise**.\n\nHere is the detailed explanation of why this happens:\n\n1.  **Filtering Tail Current Noise:** The tail current source $I_{SS}$ is a significant source of noise (thermal noise and flicker noise). Without the capacitor $C_T$, this noise current flows through the finite output impedance of the current source, creating voltage fluctuations at the tail node $P$. These fluctuations can modulate the oscillation frequency and contribute to phase noise. Adding $C_T$ creates a low-impedance path to ground for high-frequency noise, effectively shunting the noise current away and stabilizing the voltage at node $P$.\n\n2.  **Suppressing $2\\omega_0$ Noise Folding:** In a differential cross-coupled oscillator, the transistors $M_1$ and $M_2$ switch the tail current back and forth at twice the oscillation frequency ($2\\omega_0$). Due to the periodic time-varying nature of the circuit (described by the Impulse Sensitivity Function or ISF), noise components around $2\\omega_0$ at the tail node are particularly dangerous. They get \"down-converted\" or folded into phase noise around the fundamental frequency $\\omega_0$.\n    *   The capacitor $C_T$ acts as a bypass capacitor. At the frequency $2\\omega_0$, the impedance of $C_T$ ($1 / j\\omega C_T$) is low.\n    *   This low impedance shorts the noise components at $2\\omega_0$ to ground, preventing them from modulating the tail node voltage and thus preventing them from being converted into phase noise.\n\n3.  **Reducing AM-to-PM Conversion:** Fluctuations at the tail node can cause amplitude modulation (AM) which, through non-linearities in the transistors (like gate-drain capacitance $C_{gd}$), gets converted into phase modulation (PM). By stabilizing the tail node voltage, $C_T$ reduces this AM-to-PM conversion mechanism.\n\nIn summary, $C_T$ acts as a filter for the noisy tail current source, specifically targeting the harmful noise components at $2\\omega_0$, resulting in a cleaner output signal with **lower phase noise**.",
        "format": "markdown",
        "sha256": "04ccc874cfc5d20f7c977c0ea4b9b30017db4fe6af4e871adcf6accc428b45d1"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer claims CT generally and unconditionally improves phase noise by filtering tail-node noise. The effect is nonmonotonic: CT can cause flicker-noise upconversion, enable a class-C phase-noise improvement, and cause low-frequency instability if too large.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 2238,
        "total_tokens": 4800,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1731,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 2238,
        "total_tokens": 4800,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 1731,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-019-add-ct-tail-node-as-phase-noise",
      "part": "part2",
      "question_number": 19,
      "question": "We add CT to the tail node, as in the figure. What happens to the phase noise?",
      "figures": [
        "tasks/part2-019-add-ct-tail-node-as-phase-noise/figure-16.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, which shows a cross-coupled LC oscillator with an added capacitor $C_T$ at the tail node $P$, here is the analysis of what happens to the phase noise:\n\n**The phase noise decreases (improves).**\n\nHere is the detailed explanation of why this happens:\n\n1.  **Filtering Tail Current Source Noise:** The tail current source $I_{SS}$ is a significant source of noise, including thermal noise and flicker ($1/f$) noise. Without $C_T$, the noise current from $I_{SS}$ flows into the common source node $P$, creating voltage fluctuations. These fluctuations modulate the gate-source voltages ($V_{GS}$) of transistors $M_1$ and $M_2$, which can translate into phase noise. Adding $C_T$ creates a low-impedance path to ground for these noise currents, effectively shunting them away and stabilizing the voltage at node $P$.\n\n2.  **Reduction of Flicker Noise Upconversion:** In CMOS oscillators, the $1/f$ noise from the tail current source is a major contributor to close-in phase noise (the noise close to the carrier frequency). This low-frequency noise modulates the bias current, which causes amplitude modulation (AM). Due to the nonlinearity of the circuit (specifically the time-varying capacitance of the transistors), this AM is converted into phase modulation (PM), a process known as AM-to-PM conversion or noise upconversion. The capacitor $C_T$ suppresses the voltage swing at the tail node (which normally occurs at $2\\omega_0$), thereby reducing this upconversion mechanism significantly.\n\n3.  **Suppression of $2\\omega_0$ Swing:** In a standard cross-coupled oscillator, the tail node $P$ experiences a large voltage swing at twice the oscillation frequency ($2\\omega_0$). Adding a large capacitor $C_T$ acts as a bypass, forcing the tail node to act more like an AC ground. This stabilizes the common-mode operating point and reduces the sensitivity of the oscillator to noise injected at the tail.\n\nIn summary, adding $C_T$ acts as a filter for the tail node, reducing the impact of the noisy current source $I_{SS}$ and leading to a **reduction in overall phase noise**, particularly in the $1/f^3$ region close to the carrier.",
        "format": "markdown",
        "sha256": "fc88c0a2fd0081d59d1341ae26dadeca1e0e49912bc83d262196789621c6c7b9"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The answer claims CT monotonically improves phase noise by filtering tail-node noise and ripple. It misses the nonmonotonic effect, including the class-C improvement and the mechanisms that can worsen phase noise.",
          "golden_solution_sha256": "30f6431c053d0ebf26268170667295ea7bd412e72a78ea0b3247e5803cbdfc8a",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 3691,
        "total_tokens": 6253,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3176,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 2562,
        "output_tokens": 3691,
        "total_tokens": 6253,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3176,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 1,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the estimation of the oscillation frequency:\n\n**1. Circuit Identification:**\nThe circuit consists of two identical **cross-coupled LC oscillators** stacked vertically.\n*   The top block has nodes $X_1$ and $Y_1$ with inductive loads.\n*   The bottom block has nodes $X_2$ and $Y_2$ with inductive loads.\n*   The two oscillators are coupled together through the outer transistors (the ones connected to current source $I_1$). The gates of the outer transistors in the top block are driven by the outputs of the bottom block ($X_2, Y_2$), and vice-versa.\n\nThis topology is a classic **quadrature LC oscillator** (or coupled LC oscillator), used to generate two signals with a 90-degree phase difference (I and Q signals).\n\n**2. Frequency Determination:**\nThe oscillation frequency of an LC oscillator is primarily determined by the resonant frequency of its LC tank circuit.\n*   **Inductance ($L$):** Represented by the coil symbols connected to the supply rail.\n*   **Capacitance ($C$):** Although no explicit capacitors are drawn, there is always parasitic capacitance at the oscillation nodes ($X_1, Y_1$ and $X_2, Y_2$). This includes the drain-to-bulk and gate-to-drain capacitances of the transistors, as well as the parasitic capacitance of the inductors. Let's denote the total capacitance at each node as $C$.\n\nFor a symmetric coupled LC oscillator system like this, the oscillation frequency locks to the natural resonant frequency of the individual LC tanks.\n\n**3. Formula:**\nThe angular frequency $\\omega_0$ is given by:\n$$ \\omega_0 = \\frac{1}{\\sqrt{LC}} $$\n\nTherefore, the oscillation frequency $f_{osc}$ in Hertz is estimated as:\n\n$$ f_{osc} \\approx \\frac{1}{2\\pi\\sqrt{LC}} $$\n\nwhere:\n*   $L$ is the inductance of the inductors.\n*   $C$ is the total equivalent capacitance at the nodes $X_1, Y_1$ (or $X_2, Y_2$).",
        "format": "markdown",
        "sha256": "29d42f617ae60e1a044fe97d7504d1129b9628aedf19ef96f0b6b255051de331"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 1,
          "is_full_credit": false,
          "rationale": "The uncoupled tank formula is correct, but the answer misses the essential coupling-induced frequency shift, Δω ≈ αω₀/(2Q), and incorrectly claims the coupled oscillator locks exactly at resonance.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 4284,
        "total_tokens": 5794,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3770,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 4284,
        "total_tokens": 5794,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 3770,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 1,
        "score_percent": 25,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 2,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit diagram provided, here is the estimation of the oscillation frequency:\n\n**1. Circuit Identification**\nThe circuit shown is a **quadrature LC oscillator**. It consists of two identical cross-coupled LC oscillators (the top block with nodes $X_1, Y_1$ and the bottom block with nodes $X_2, Y_2$) that are coupled together.\n*   **Core Oscillators:** Each block contains a cross-coupled NMOS pair (the central transistors) acting as a negative resistance generator to sustain oscillation, and inductors acting as the reactive load.\n*   **Coupling:** The outer transistors provide coupling between the two oscillators. The gates of the outer transistors in the top block are driven by the outputs of the bottom block ($X_2, Y_2$), and vice-versa. This specific topology (parallel coupling) forces the two oscillators to lock to the same frequency with a 90-degree phase difference (quadrature outputs).\n\n**2. Frequency Determination**\nThe oscillation frequency of an LC oscillator is primarily determined by the resonant frequency of its LC tank circuit.\n*   **Inductance ($L$):** Represented by the coil symbols connected to the supply rail.\n*   **Capacitance ($C$):** Although no explicit capacitors are drawn, there is inherent parasitic capacitance at the nodes $X_1, Y_1$ and $X_2, Y_2$ (due to the transistor drain/gate capacitances and wiring). Let's denote this total capacitance as $C$.\n\nFor a coupled LC oscillator system operating in quadrature mode, the oscillation frequency is approximately equal to the natural resonant frequency of the individual LC tanks.\n\n**3. Formula**\nThe angular frequency $\\omega_{osc}$ is given by:\n$$ \\omega_{osc} \\approx \\frac{1}{\\sqrt{LC}} $$\n\nThe frequency in Hertz ($f_{osc}$) is:\n$$ f_{osc} \\approx \\frac{1}{2\\pi\\sqrt{LC}} $$\n\nWhere:\n*   $L$ is the inductance of the inductors.\n*   $C$ is the total parasitic capacitance at the oscillation nodes ($X$ and $Y$).",
        "format": "markdown",
        "sha256": "df057bdeb3b7b6170227fbd0f8d0384fa75138a4d55d22529558e7b5329a4c25"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "Correctly gives the LC tank resonance as a baseline, but misses the essential coupling-induced frequency shift and incorrectly treats the oscillation frequency as approximately the uncoupled tank resonance.",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 5872,
        "total_tokens": 7382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5367,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 5872,
        "total_tokens": 7382,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 5367,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    },
    {
      "question_id": "part2-020-estimate-oscillation-frequency",
      "part": "part2",
      "question_number": 20,
      "question": "Estimate the oscillation frequency of the circuit in the figure.",
      "figures": [
        "tasks/part2-020-estimate-oscillation-frequency/figure-17.png"
      ],
      "rollout": 3,
      "configuration": {
        "model_id": null,
        "thinking_effort": "max",
        "api_model": "qwen/qwen3.7-plus",
        "route": "openrouter_chat_completions"
      },
      "answer": {
        "text": "Based on the circuit schematic provided, here is the estimation of the oscillation frequency:\n\n**1. Circuit Identification**\nThe circuit shown is a **Quadrature LC Oscillator** (also known as a coupled LC oscillator). It consists of two identical cross-coupled LC oscillators stacked vertically.\n*   **Top Block:** An LC oscillator with nodes $X_1$ and $Y_1$, inductive loads, a cross-coupled NMOS pair (biased by $I_{SS}$), and coupling transistors (biased by $I_1$).\n*   **Bottom Block:** An identical LC oscillator with nodes $X_2$ and $Y_2$.\n*   **Coupling:** The two oscillators are coupled together through the outer transistors. The gates of the outer transistors in the top block are connected to the outputs of the bottom block ($X_2, Y_2$), and vice-versa. This symmetric coupling forces the two oscillators to run at the same frequency but with a 90-degree phase difference (quadrature signals).\n\n**2. Frequency Determination**\nThe oscillation frequency of an LC oscillator is primarily determined by the resonant frequency of its LC tank circuit.\n*   **Inductance ($L$):** Represented by the spiral inductors connected to the supply rail.\n*   **Capacitance ($C$):** Although no explicit capacitors are drawn, there is a total parasitic capacitance at the nodes $X_1, Y_1$ and $X_2, Y_2$. This capacitance ($C_{total}$) includes the drain-bulk and gate-drain capacitances of the transistors, as well as the parasitic capacitance of the inductors.\n\n**3. Estimate**\nFor weak to moderate coupling (which is typical for this topology to maintain good phase noise and quadrature accuracy), the oscillation frequency is very close to the natural resonant frequency of the individual LC tanks.\n\nThe angular frequency $\\omega_{osc}$ is estimated as:\n$$ \\omega_{osc} \\approx \\frac{1}{\\sqrt{L C_{total}}} $$\n\nThe frequency in Hertz ($f_{osc}$) is:\n$$ f_{osc} \\approx \\frac{1}{2\\pi\\sqrt{L C_{total}}} $$\n\nWhere:\n*   $L$ is the inductance of the load inductors.\n*   $C_{total}$ is the total equivalent capacitance at the oscillation nodes ($X$ and $Y$).\n\n*Note: The coupling current $I_1$ introduces a small frequency shift relative to the ideal tank resonance, but $\\frac{1}{2\\pi\\sqrt{LC}}$ is the standard first-order estimate.*",
        "format": "markdown",
        "sha256": "a6526d428acb2349196e56f7439d7961606cf4a9fb2d3e873b84d712aec8425f"
      },
      "model_call_count": 1,
      "internet_or_tool_evidence": false,
      "source_experiment": "2026-11-09-question-only-rerun",
      "scores": {
        "gpt_6_luna_max": {
          "score_0_to_4": 2,
          "is_full_credit": false,
          "rationale": "The tank-resonance estimate is correct, and the answer acknowledges a coupling-induced shift, but it does not estimate that shift using the required coupling-dependent term (such as αω₀/(2Q)).",
          "golden_solution_sha256": "9fb09917ae8858f8003213ac52eae9cc4403612167903aff6685adcc43ddd686",
          "rubric_sha256": "7c95b8e3a1a51fcebb49a1ad05e777ad488f398109bed3af7814ed1709b67a54",
          "judge_model": "openai/gpt-6-luna"
        }
      },
      "tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 8139,
        "total_tokens": 9649,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7542,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "selected_response_tokens": {
        "cached_input_tokens": 0,
        "input_tokens": 1510,
        "output_tokens": 8139,
        "total_tokens": 9649,
        "cache_creation_input_tokens": null,
        "reasoning_output_tokens": 7542,
        "complete": true,
        "availability": "complete",
        "missing_fields": []
      },
      "attempt_count": 1,
      "active_score": {
        "policy": "gpt_6_luna_max",
        "score_0_to_4": 2,
        "score_percent": 50,
        "is_full_credit": false
      }
    }
  ]
}
